Skip to contentSkip to conversation

staging: iio: Single source header file reorganization

PATCH Superseded Sreya Mittal 2 participants 2 messages Feb 25, 2017

Subsystems (3)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 staging: iio: Single source header file reorganization

The contents of the header file are used only by this single source file. Move content into .c and remove .h.

---
 drivers/staging/iio/trigger/iio-trig-bfin-timer.c | 33 +++++++++++++++++------
 drivers/staging/iio/trigger/iio-trig-bfin-timer.h | 24 -----------------
 2 files changed, 25 insertions(+), 32 deletions(-)
 delete mode 100644 drivers/staging/iio/trigger/iio-trig-bfin-timer.h
drivers/staging/iio/trigger/iio-trig-bfin-timer.c +25 -8
index 4e0b4ee..f01462b 100644
@@ -5,21 +5,38 @@
  *
  */
 
+#include <asm/gptimers.h>
+#include <asm/portmux.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/delay.h>
-
-#include <asm/gptimers.h>
-#include <asm/portmux.h>
-
 #include <linux/iio/iio.h>
 #include <linux/iio/trigger.h>
 
-#include "iio-trig-bfin-timer.h"
+/**
+ *  * struct iio_bfin_timer_trigger_pdata - timer trigger platform data
+ *   * @output_enable: Enable external trigger pulse generation.
+ *    * @active_low: Whether the trigger pulse is active low.
+ *     * @duty_ns: Length of the trigger pulse in nanoseconds.
+ *      *
+ *       * This struct is used to configure the output pulse generation of the blackfin
+ *        * timer trigger. If output_enable is set to true an external trigger signal
+ *         * will generated on the pin corresponding to the timer. This is useful for
+ *          * converters which needs an external signal to start conversion. active_low and
+ *           * duty_ns are used to configure the type of the trigger pulse. If output_enable
+ *            * is set to false no external trigger pulse will be generated and active_low
+ *             * and duty_ns are ignored.
+ *              **/
+
+struct iio_bfin_timer_trigger_pdata {
+		bool output_enable;
+			bool active_low;
+				unsigned int duty_ns;
+};
 
 struct bfin_timer {
 	unsigned short id, bit;
drivers/staging/iio/trigger/iio-trig-bfin-timer.h deleted +0 -24
deleted file mode 100644
index c07321f..0000000
@@ -1,24 +0,0 @@
-#ifndef __IIO_BFIN_TIMER_TRIGGER_H__
-#define __IIO_BFIN_TIMER_TRIGGER_H__
-
-/**
- * struct iio_bfin_timer_trigger_pdata - timer trigger platform data
- * @output_enable: Enable external trigger pulse generation.
- * @active_low: Whether the trigger pulse is active low.
- * @duty_ns: Length of the trigger pulse in nanoseconds.
- *
- * This struct is used to configure the output pulse generation of the blackfin
- * timer trigger. If output_enable is set to true an external trigger signal
- * will generated on the pin corresponding to the timer. This is useful for
- * converters which needs an external signal to start conversion. active_low and
- * duty_ns are used to configure the type of the trigger pulse. If output_enable
- * is set to false no external trigger pulse will be generated and active_low
- * and duty_ns are ignored.
- **/
-struct iio_bfin_timer_trigger_pdata {
-	bool output_enable;
-	bool active_low;
-	unsigned int duty_ns;
-};
-
-#endif
Signature · 1 line
2.9.3
#1 lore raw
Quoted 4 lines · Sreya Mittal

The contents of the header file are used only by this single source file. Move content into .c and remove .h.

Hi,

In general the intend of the patch is correct, but it looks like something went wrong with the indention of the documentation.

[....]

Quoted 15 lines
drivers/staging/iio/trigger/iio-trig-bfin-timer.c +14 -1
-#include "iio-trig-bfin-timer.h"
+/**
+ *  * struct iio_bfin_timer_trigger_pdata - timer trigger platform data
+ *   * @output_enable: Enable external trigger pulse generation.
+ *    * @active_low: Whether the trigger pulse is active low.
+ *     * @duty_ns: Length of the trigger pulse in nanoseconds.
+ *      *
+ *       * This struct is used to configure the output pulse generation of the blackfin
+ *        * timer trigger. If output_enable is set to true an external trigger signal
+ *         * will generated on the pin corresponding to the timer. This is useful for
+ *          * converters which needs an external signal to start conversion. active_low and
+ *           * duty_ns are used to configure the type of the trigger pulse. If output_enable
+ *            * is set to false no external trigger pulse will be generated and active_low
+ *             * and duty_ns are ignored.
+ *              **/