configs: at91sam9x5ek: add development rootfs

PATCH New Ludovic Desroches 4 participants 17 messages Nov 3, 2016 – Mar 8, 2017 Arm/Microchip (AT91) SoC support

lore

Share & tools

lore

Ludovic Desroches

author

2016-11-03 14:08 UTC #0 lore raw

PATCH 1/4 configs: at91sam9x5ek: add development rootfs

Add development rootfs based on linux4sam_5.4 for at91sam9x5ek for both NAND flash and SD card.

Signed-off-by Ludovic Desroches <[email protected]>

---
 board/atmel/at91sam9x5ek_mmc/genimage.cfg  |  34 ++++++++++
 board/atmel/at91sam9x5ek_mmc/post-image.sh |  20 ++++++
 configs/at91sam9x5ek_dev_defconfig         |  99 ++++++++++++++++++++++++++++
 configs/at91sam9x5ek_mmc_dev_defconfig     | 102 +++++++++++++++++++++++++++++
 4 files changed, 255 insertions(+)
 create mode 100644 board/atmel/at91sam9x5ek_mmc/genimage.cfg
 create mode 100755 board/atmel/at91sam9x5ek_mmc/post-image.sh
 create mode 100644 configs/at91sam9x5ek_dev_defconfig
 create mode 100644 configs/at91sam9x5ek_mmc_dev_defconfig

board/atmel/at91sam9x5ek_mmc/genimage.cfg new file +34 -0

new file mode 100644
index 0000000..46c2dc9
@@ -0,0 +1,34 @@
+# Image for SD card boot on Atmel at91sam9x5ek boards
+#
+image boot.vfat {
+	vfat {
+		files = {
+			"zImage",
+			"at91sam9g15ek.dtb",
+			"at91sam9g25ek.dtb",
+			"at91sam9g35ek.dtb",
+			"at91sam9x25ek.dtb",
+			"at91sam9x35ek.dtb",
+			"boot.bin",
+			"u-boot.bin"
+		}
+	}
+	size = 16M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+		size = 512M
+	}
+}

board/atmel/at91sam9x5ek_mmc/post-image.sh new file +20 -0

new file mode 100755
index 0000000..b560fd3
@@ -0,0 +1,20 @@
+#!/bin/sh
+
+BOARD_DIR="$(dirname $0)"
+GENIMAGE_CFG="${BOARD_DIR}/genimage.cfg"
+GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
+
+rm -rf "${GENIMAGE_TMP}"
+
+echo --rootpath "${TARGET_DIR}"
+echo --tmppath "${GENIMAGE_TMP}"
+echo --inputpath "${BINARIES_DIR}"
+echo --outputpath "${BINARIES_DIR}"
+echo --config "${GENIMAGE_CFG}"
+
+genimage                               \
+	--rootpath "${TARGET_DIR}"     \
+	--tmppath "${GENIMAGE_TMP}"    \
+	--inputpath "${BINARIES_DIR}"  \
+	--outputpath "${BINARIES_DIR}" \
+	--config "${GENIMAGE_CFG}"

configs/at91sam9x5ek_dev_defconfig new file +99 -0

99 lines not on this page · raw message

configs/at91sam9x5ek_mmc_dev_defconfig new file +102 -0

102 lines not on this page · raw message

Signature · 1 line

2.9.0

Ludovic Desroches

author

2016-11-03 14:08 UTC #1 lore raw

PATCH 2/4 board: atmel: genimage: add 1M offset for FAT partition

Signed-off-by Ludovic Desroches <[email protected]>

---
 board/atmel/at91sam9x5ek_mmc/genimage.cfg     | 1 +
 board/atmel/sama5d2_xplained_mmc/genimage.cfg | 1 +
 board/atmel/sama5d3_xplained_mmc/genimage.cfg | 1 +
 board/atmel/sama5d4_xplained_mmc/genimage.cfg | 1 +
 4 files changed, 4 insertions(+)

board/atmel/at91sam9x5ek_mmc/genimage.cfg +1 -0

index 46c2dc9..b2be647 100644
@@ -24,6 +24,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {

board/atmel/sama5d2_xplained_mmc/genimage.cfg +1 -0

index b0ba22d..d3b7af5 100644
@@ -23,6 +23,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {

board/atmel/sama5d3_xplained_mmc/genimage.cfg +1 -0

index 32df453..277ce5f 100644
@@ -23,6 +23,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {

board/atmel/sama5d4_xplained_mmc/genimage.cfg +1 -0

index b23ebe4..70bb3e4 100644
@@ -24,6 +24,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {

Signature · 1 line

2.9.0

Thomas Petazzoni

2016-11-03 14:20 UTC #2 lore raw

PATCH 2/4 board: atmel: genimage: add 1M offset for FAT partition

Hello,

Quoted 1 line · Ludovic Desroches

Signed-off-by Ludovic Desroches <[email protected]>

An empty commit log is a bit strange. This really needs some explanation.

Thanks,

Thomas

Signature · 3 lines

Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Ludovic Desroches

author

2016-11-04 10:15 UTC #3 lore raw

PATCH 2/4 board: atmel: genimage: add 1M offset for FAT partition

With older SoCs and some SD cards, a 1024-bytes offset is needed to allow ROM code to read the content of the FAT partition. As it is usual to get a 1M bytes offset for the first partition, use this value to avoid boot issues.

Signed-off-by Ludovic Desroches <[email protected]>

---
 board/atmel/at91sam9x5ek_mmc/genimage.cfg     | 1 +
 board/atmel/sama5d2_xplained_mmc/genimage.cfg | 1 +
 board/atmel/sama5d3_xplained_mmc/genimage.cfg | 1 +
 board/atmel/sama5d4_xplained_mmc/genimage.cfg | 1 +
 4 files changed, 4 insertions(+)

board/atmel/at91sam9x5ek_mmc/genimage.cfg +1 -0

index 46c2dc9..b2be647 100644
@@ -24,6 +24,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {

board/atmel/sama5d2_xplained_mmc/genimage.cfg +1 -0

index b0ba22d..d3b7af5 100644
@@ -23,6 +23,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {

board/atmel/sama5d3_xplained_mmc/genimage.cfg +1 -0

index 32df453..277ce5f 100644
@@ -23,6 +23,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {

board/atmel/sama5d4_xplained_mmc/genimage.cfg +1 -0

index b23ebe4..70bb3e4 100644
@@ -24,6 +24,7 @@ image sdcard.img {
 		partition-type = 0xC
 		bootable = "true"
 		image = "boot.vfat"
+		offset = 1M
 	}
 
 	partition rootfs {

Signature · 1 line

2.9.0

Thomas Petazzoni

2016-11-04 10:47 UTC #4 lore raw

PATCH 2/4 board: atmel: genimage: add 1M offset for FAT partition

Hello,

Quoted 5 lines · Ludovic Desroches

With older SoCs and some SD cards, a 1024-bytes offset is needed to allow ROM code to read the content of the FAT partition. As it is usual to get a 1M bytes offset for the first partition, use this value to avoid boot issues.

Quoted 7 lines

Signed-off-by Ludovic Desroches <[email protected]>

---
 board/atmel/at91sam9x5ek_mmc/genimage.cfg     | 1 +
 board/atmel/sama5d2_xplained_mmc/genimage.cfg | 1 +
 board/atmel/sama5d3_xplained_mmc/genimage.cfg | 1 +
 board/atmel/sama5d4_xplained_mmc/genimage.cfg | 1 +
 4 files changed, 4 insertions(+)

I've applied to master, after removing the hunk changing board/atmel/at91sam9x5ek_mmc/genimage.cfg. Indeed, this file doesn't exist in master since I haven't committed your PATCH 1/4. It is indeed weird to:

1/ Have patches making fixes *after* patches adding new features in a
patch series. It should be the other way around.

2/ In PATCH 1/4, introduce a genimage.cfg file for the
at91sam9x5ek_mmc configuration that is wrong, and gets fixed in PATCH 2/4.

Anyway, this one is applied to master for SAMA5D{2,3,4}, we will handle 9x5EK separately.

Thanks!

Thomas

Signature · 3 lines

Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Ludovic Desroches

author

2016-11-04 13:01 UTC #5 lore raw

PATCH 2/4 board: atmel: genimage: add 1M offset for FAT partition

Quoted 21 lines · Thomas Petazzoni

Hello,
Quoted 5 lines · Ludovic Desroches
With older SoCs and some SD cards, a 1024-bytes offset is needed to allow ROM code to read the content of the FAT partition. As it is usual to get a 1M bytes offset for the first partition, use this value to avoid boot issues.
Quoted 7 lines
Signed-off-by Ludovic Desroches <[email protected]>
---
 board/atmel/at91sam9x5ek_mmc/genimage.cfg     | 1 +
 board/atmel/sama5d2_xplained_mmc/genimage.cfg | 1 +
 board/atmel/sama5d3_xplained_mmc/genimage.cfg | 1 +
 board/atmel/sama5d4_xplained_mmc/genimage.cfg | 1 +
 4 files changed, 4 insertions(+)
I've applied to master, after removing the hunk changing board/atmel/at91sam9x5ek_mmc/genimage.cfg. Indeed, this file doesn't exist in master since I haven't committed your PATCH 1/4. It is indeed weird to:

Quoted 7 lines

1/ Have patches making fixes *after* patches adding new features in a
patch series. It should be the other way around.
2/ In PATCH 1/4, introduce a genimage.cfg file for the
at91sam9x5ek_mmc configuration that is wrong, and gets fixed in PATCH 2/4.

Sorry, in fact patch 1/4 was done for linux4sam_5.4 but I didn't sent it because we had some issues with this release and we discovered the sd card boot issue when testing the linux4sam_5.5 release.

Quoted 2 lines

Anyway, this one is applied to master for SAMA5D{2,3,4}, we will handle 9x5EK separately.

Thanks

Ludovic

Quoted 8 lines

Thanks!

Thomas

Signature · 3 lines

Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Ludovic Desroches

author

2016-11-03 14:08 UTC #6 lore raw

PATCH 3/4 configs: atmel: xplained boards: bump to linux4sam_5.5

In reply to Ludovic Desroches

Bump at91bootstrap to v3.8.7, U-Boot to linux4sam_5.5, Linux to linux4sam_5.5 (based on v4.4.x).

Signed-off-by Ludovic Desroches <[email protected]>

---
 configs/atmel_sama5d2_xplained_mmc_defconfig     | 8 ++++----
 configs/atmel_sama5d2_xplained_mmc_dev_defconfig | 8 ++++----
 configs/atmel_sama5d3_xplained_defconfig         | 8 ++++----
 configs/atmel_sama5d3_xplained_dev_defconfig     | 8 ++++----
 configs/atmel_sama5d3_xplained_mmc_defconfig     | 8 ++++----
 configs/atmel_sama5d3_xplained_mmc_dev_defconfig | 8 ++++----
 configs/atmel_sama5d4_xplained_defconfig         | 8 ++++----
 configs/atmel_sama5d4_xplained_dev_defconfig     | 8 ++++----
 configs/atmel_sama5d4_xplained_mmc_defconfig     | 8 ++++----
 configs/atmel_sama5d4_xplained_mmc_dev_defconfig | 8 ++++----
 10 files changed, 40 insertions(+), 40 deletions(-)

configs/atmel_sama5d2_xplained_mmc_defconfig +4 -4

index 7eb969f..13086af 100644
@@ -3,12 +3,12 @@ BR2_cortex_a5=y
 BR2_ARM_ENABLE_NEON=y
 BR2_ARM_ENABLE_VFP=y
 BR2_ARM_INSTRUCTIONS_THUMB2=y
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 BR2_ROOTFS_POST_IMAGE_SCRIPT="board/atmel/sama5d2_xplained_mmc/post-image.sh"
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="sama5"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-sama5d2_xplained at91-sama5d2_xplained_pda4 at91-sama5d2_xplained_pda7 at91-sama5d2_xplained_pda7b"

@@ -17,13 +17,13 @@ BR2_TARGET_ROOTFS_EXT2_4=y
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.5"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="sama5d2_xplainedsd_uboot"
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="sama5d2_xplained_mmc"
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
 BR2_PACKAGE_HOST_GENIMAGE=y

configs/atmel_sama5d2_xplained_mmc_dev_defconfig +4 -4

index d7f4717..a225091 100644
@@ -6,7 +6,7 @@ BR2_ARM_ENABLE_VFP=y
 BR2_ARM_INSTRUCTIONS_THUMB2=y
 
 # Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 # Needed for some packages
 BR2_TOOLCHAIN_BUILDROOT_WCHAR=y
 # Needed for gdb

@@ -24,7 +24,7 @@ BR2_ROOTFS_POST_IMAGE_SCRIPT="board/atmel/sama5d2_xplained_mmc/post-image.sh"
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="sama5"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-sama5d2_xplained at91-sama5d2_xplained_pda4 at91-sama5d2_xplained_pda7 at91-sama5d2_xplained_pda7b"

@@ -89,13 +89,13 @@ BR2_TARGET_ROOTFS_EXT2_4=y
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.5"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="sama5d2_xplainedsd_uboot"
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="sama5d2_xplained_mmc"
 
 # Host packages

configs/atmel_sama5d3_xplained_defconfig +4 -4

index 480f2fd..307bbaa 100644
@@ -2,11 +2,11 @@ BR2_arm=y
 BR2_cortex_a5=y
 BR2_ARM_ENABLE_VFP=y
 BR2_ARM_INSTRUCTIONS_THUMB2=y
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="sama5"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-sama5d3_xplained at91-sama5d3_xplained_pda4 at91-sama5d3_xplained_pda7 at91-sama5d3_xplained_pda7b"

@@ -17,12 +17,12 @@ BR2_TARGET_ROOTFS_UBI_SUBSIZE=2048
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.5"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="sama5d3_xplainednf_uboot"
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="sama5d3_xplained_nandflash"
 BR2_PACKAGE_HOST_SAM_BA=y

configs/atmel_sama5d3_xplained_dev_defconfig +4 -4

index d51a141..4905148 100644
@@ -5,7 +5,7 @@ BR2_ARM_ENABLE_VFP=y
 BR2_ARM_INSTRUCTIONS_THUMB2=y
 
 # Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 # Needed for some packages
 BR2_TOOLCHAIN_BUILDROOT_WCHAR=y
 # Needed for gdb

@@ -21,7 +21,7 @@ BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_EUDEV=y
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="sama5"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-sama5d3_xplained at91-sama5d3_xplained_pda4 at91-sama5d3_xplained_pda7 at91-sama5d3_xplained_pda7b"

@@ -88,13 +88,13 @@ BR2_TARGET_ROOTFS_UBI_SUBSIZE=2048
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.5"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="sama5d3_xplainednf_uboot"
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="sama5d3_xplained_nandflash"
 
 # Host packages

configs/atmel_sama5d3_xplained_mmc_defconfig +4 -4

index 14ca3f5..0a44dc7 100644
@@ -2,12 +2,12 @@ BR2_arm=y
 BR2_cortex_a5=y
 BR2_ARM_ENABLE_VFP=y
 BR2_ARM_INSTRUCTIONS_THUMB2=y
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 BR2_ROOTFS_POST_IMAGE_SCRIPT="board/atmel/sama5d3_xplained_mmc/post-image.sh"
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="sama5"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-sama5d3_xplained at91-sama5d3_xplained_pda4 at91-sama5d3_xplained_pda7 at91-sama5d3_xplained_pda7b"

@@ -16,13 +16,13 @@ BR2_TARGET_ROOTFS_EXT2_4=y
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.5"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="sama5d3_xplainedsd_uboot"
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="sama5d3_xplained_mmc"
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
 BR2_PACKAGE_HOST_GENIMAGE=y

configs/atmel_sama5d3_xplained_mmc_dev_defconfig +4 -4

index c45c2ce..1fc8452 100644
@@ -5,7 +5,7 @@ BR2_ARM_ENABLE_VFP=y
 BR2_ARM_INSTRUCTIONS_THUMB2=y
 
 # Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 # Needed for some packages
 BR2_TOOLCHAIN_BUILDROOT_WCHAR=y
 # Needed for gdb

@@ -23,7 +23,7 @@ BR2_ROOTFS_POST_IMAGE_SCRIPT="board/atmel/sama5d3_xplained_mmc/post-image.sh"
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="sama5"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-sama5d3_xplained at91-sama5d3_xplained_pda4 at91-sama5d3_xplained_pda7 at91-sama5d3_xplained_pda7b"

@@ -88,13 +88,13 @@ BR2_TARGET_ROOTFS_EXT2_4=y
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.5"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="sama5d3_xplainedsd_uboot"
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="sama5d3_xplained_mmc"
 
 # Host packages

configs/atmel_sama5d4_xplained_defconfig +4 -4

index 65313f3..5646723 100644
@@ -3,11 +3,11 @@ BR2_cortex_a5=y
 BR2_ARM_ENABLE_NEON=y
 BR2_ARM_ENABLE_VFP=y
 BR2_ARM_INSTRUCTIONS_THUMB2=y
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="sama5"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-sama5d4_xplained at91-sama5d4_xplained_hdmi at91-sama5d4_xplained_pda4 at91-sama5d4_xplained_pda7 at91-sama5d4_xplained_pda7b"

@@ -21,12 +21,12 @@ BR2_TARGET_ROOTFS_UBI_SUBSIZE=0
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.5"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="sama5d4_xplainednf_uboot_secure"
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="sama5d4_xplained_nandflash"
 BR2_PACKAGE_HOST_SAM_BA=y

configs/atmel_sama5d4_xplained_dev_defconfig +4 -4

index 7dadeca..b3dc815 100644
@@ -6,7 +6,7 @@ BR2_ARM_ENABLE_VFP=y
 BR2_ARM_INSTRUCTIONS_THUMB2=y
 
 # Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 # Needed for some packages
 BR2_TOOLCHAIN_BUILDROOT_WCHAR=y
 # Needed for gdb

@@ -22,7 +22,7 @@ BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_EUDEV=y
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="sama5"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-sama5d4_xplained at91-sama5d4_xplained_hdmi at91-sama5d4_xplained_pda4 at91-sama5d4_xplained_pda7 at91-sama5d4_xplained_pda7b"

@@ -92,13 +92,13 @@ BR2_TARGET_ROOTFS_UBI_SUBSIZE=0
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.5"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="sama5d4_xplainednf_uboot_secure"
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="sama5d4_xplained_nandflash"
 
 # Host packages

configs/atmel_sama5d4_xplained_mmc_defconfig +4 -4

index 7f93a82..03055cf 100644
@@ -3,12 +3,12 @@ BR2_cortex_a5=y
 BR2_ARM_ENABLE_NEON=y
 BR2_ARM_ENABLE_VFP=y
 BR2_ARM_INSTRUCTIONS_THUMB2=y
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 BR2_ROOTFS_POST_IMAGE_SCRIPT="board/atmel/sama5d4_xplained_mmc/post-image.sh"
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="sama5"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-sama5d4_xplained at91-sama5d4_xplained_hdmi at91-sama5d4_xplained_pda4 at91-sama5d4_xplained_pda7 at91-sama5d4_xplained_pda7b"

@@ -17,13 +17,13 @@ BR2_TARGET_ROOTFS_EXT2_4=y
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.5"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="sama5d4_xplainedsd_uboot_secure"
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="sama5d4_xplained_mmc"
 BR2_PACKAGE_HOST_DOSFSTOOLS=y
 BR2_PACKAGE_HOST_GENIMAGE=y

configs/atmel_sama5d4_xplained_mmc_dev_defconfig +4 -4

index 9e11efa..1d4cfcb 100644
@@ -6,7 +6,7 @@ BR2_ARM_ENABLE_VFP=y
 BR2_ARM_INSTRUCTIONS_THUMB2=y
 
 # Toolchain
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_1=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 # Needed for some packages
 BR2_TOOLCHAIN_BUILDROOT_WCHAR=y
 # Needed for gdb

@@ -24,7 +24,7 @@ BR2_ROOTFS_POST_IMAGE_SCRIPT="board/atmel/sama5d4_xplained_mmc/post-image.sh"
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="sama5"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91-sama5d4_xplained at91-sama5d4_xplained_hdmi at91-sama5d4_xplained_pda4 at91-sama5d4_xplained_pda7 at91-sama5d4_xplained_pda7b"

@@ -89,13 +89,13 @@ BR2_TARGET_ROOTFS_EXT2_4=y
 BR2_TARGET_AT91BOOTSTRAP3=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
 BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
-BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.5"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="sama5d4_xplainedsd_uboot_secure"
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.3"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_TARGET_UBOOT_BOARD_DEFCONFIG="sama5d4_xplained_mmc"
 
 # Host packages

Signature · 1 line

2.9.0

Thomas Petazzoni

Applied

2016-11-03 21:40 UTC #7 lore raw

PATCH 3/4 configs: atmel: xplained boards: bump to linux4sam_5.5

Hello,

Quoted 4 lines · Ludovic Desroches

Bump at91bootstrap to v3.8.7, U-Boot to linux4sam_5.5, Linux to linux4sam_5.5 (based on v4.4.x).
Signed-off-by Ludovic Desroches <[email protected]>

Quoted 12 lines

---
 configs/atmel_sama5d2_xplained_mmc_defconfig     | 8 ++++----
 configs/atmel_sama5d2_xplained_mmc_dev_defconfig | 8 ++++----
 configs/atmel_sama5d3_xplained_defconfig         | 8 ++++----
 configs/atmel_sama5d3_xplained_dev_defconfig     | 8 ++++----
 configs/atmel_sama5d3_xplained_mmc_defconfig     | 8 ++++----
 configs/atmel_sama5d3_xplained_mmc_dev_defconfig | 8 ++++----
 configs/atmel_sama5d4_xplained_defconfig         | 8 ++++----
 configs/atmel_sama5d4_xplained_dev_defconfig     | 8 ++++----
 configs/atmel_sama5d4_xplained_mmc_defconfig     | 8 ++++----
 configs/atmel_sama5d4_xplained_mmc_dev_defconfig | 8 ++++----
 10 files changed, 40 insertions(+), 40 deletions(-)

Applied to master, thanks.

Thomas

Signature · 3 lines

Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Ludovic Desroches

author

2016-11-03 14:08 UTC #8 lore raw

PATCH 4/4 configs: atmel: at91sam9x5ek: bump to linux4sam_5.5

In reply to Ludovic Desroches

Bump at91bootstrap to v3.8.7, U-Boot to linux4sam_5.5, Linux to linux4sam_5.5 (based on v4.4.x).

Signed-off-by Ludovic Desroches <[email protected]>

---
 configs/at91sam9x5ek_defconfig | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)

configs/at91sam9x5ek_defconfig +9 -5

index 79031b6..69f9e75 100644
@@ -1,11 +1,11 @@
 BR2_arm=y
 BR2_arm926t=y
-# Linux headers same as kernel, a 3.18 series
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_3_18=y
+# Linux headers same as kernel, a 4.4 series
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_4=y
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_GIT=y
 BR2_LINUX_KERNEL_CUSTOM_REPO_URL="https://github.com/linux4sam/linux-at91.git"
-BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="03329ca4cf6b94acc5c65b59b2d1f90fdeee0887"
+BR2_LINUX_KERNEL_CUSTOM_REPO_VERSION="linux4sam_5.5"
 BR2_LINUX_KERNEL_DEFCONFIG="at91_dt"
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="at91sam9g15ek at91sam9g25ek at91sam9g35ek at91sam9x25ek at91sam9x35ek"

@@ -14,10 +14,14 @@ BR2_TARGET_ROOTFS_UBIFS_LEBSIZE=0x1f000
 BR2_TARGET_ROOTFS_UBI=y
 BR2_TARGET_ROOTFS_UBI_SUBSIZE=2048
 BR2_TARGET_AT91BOOTSTRAP3=y
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_GIT=y
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_URL="https://github.com/linux4sam/at91bootstrap.git"
+BR2_TARGET_AT91BOOTSTRAP3_CUSTOM_REPO_VERSION="v3.8.7"
 BR2_TARGET_AT91BOOTSTRAP3_DEFCONFIG="at91sam9x5eknf_uboot"
 BR2_TARGET_UBOOT=y
-BR2_TARGET_UBOOT_BOARDNAME="at91sam9x5ek_nandflash"
+BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y
 BR2_TARGET_UBOOT_CUSTOM_GIT=y
 BR2_TARGET_UBOOT_CUSTOM_REPO_URL="https://github.com/linux4sam/u-boot-at91.git"
-BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="677f3c2340b72131beebace8e96cac17b9569887"
+BR2_TARGET_UBOOT_CUSTOM_REPO_VERSION="linux4sam_5.5"
+BR2_TARGET_UBOOT_BOARD_DEFCONFIG="at91sam9x5ek_nandflash"
 BR2_PACKAGE_HOST_SAM_BA=y

Signature · 1 line

2.9.0

Thomas Petazzoni

Applied

2016-11-03 21:40 UTC #9 lore raw

PATCH 4/4 configs: atmel: at91sam9x5ek: bump to linux4sam_5.5

Hello,

Quoted 7 lines · Ludovic Desroches

Bump at91bootstrap to v3.8.7, U-Boot to linux4sam_5.5, Linux to linux4sam_5.5 (based on v4.4.x).
Signed-off-by Ludovic Desroches <[email protected]>
---
 configs/at91sam9x5ek_defconfig | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)

Applied to master, thanks.

Thomas

Signature · 3 lines

Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Thomas Petazzoni

2016-11-04 10:48 UTC #10 lore raw

PATCH 1/4 configs: at91sam9x5ek: add development rootfs

In reply to Ludovic Desroches

Hello,

Quoted 9 lines · Ludovic Desroches

Add development rootfs based on linux4sam_5.4 for at91sam9x5ek for both NAND flash and SD card.
Signed-off-by Ludovic Desroches <[email protected]>
---
 board/atmel/at91sam9x5ek_mmc/genimage.cfg  |  34 ++++++++++
 board/atmel/at91sam9x5ek_mmc/post-image.sh |  20 ++++++
 configs/at91sam9x5ek_dev_defconfig         |  99 ++++++++++++++++++++++++++++
 configs/at91sam9x5ek_mmc_dev_defconfig     | 102 +++++++++++++++++++++++++++++

So after this patch, we would have:

at91sam9x5ek_defconfig
at91sam9x5ek_dev_defconfig
at91sam9x5ek_mmc_dev_defconfig

But no minimal MMC configuration.

That's a lot of configurations for a single board. Can we rationalize a bit, and chose one configuration only (either NAND or MMC), for which we have the minimal and dev configurations?

Thanks,

Thomas

Signature · 3 lines

Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Ludovic Desroches

author

2016-11-04 13:14 UTC #11 lore raw

PATCH 1/4 configs: at91sam9x5ek: add development rootfs

Quoted 19 lines · Thomas Petazzoni

Hello,
Quoted 9 lines · Ludovic Desroches
Add development rootfs based on linux4sam_5.4 for at91sam9x5ek for both NAND flash and SD card.
Signed-off-by Ludovic Desroches <[email protected]>
---
 board/atmel/at91sam9x5ek_mmc/genimage.cfg  |  34 ++++++++++
 board/atmel/at91sam9x5ek_mmc/post-image.sh |  20 ++++++
 configs/at91sam9x5ek_dev_defconfig         |  99 ++++++++++++++++++++++++++++
 configs/at91sam9x5ek_mmc_dev_defconfig     | 102 +++++++++++++++++++++++++++++
So after this patch, we would have:
at91sam9x5ek_defconfig
at91sam9x5ek_dev_defconfig
at91sam9x5ek_mmc_dev_defconfig

Quoted 6 lines

But no minimal MMC configuration.
That's a lot of configurations for a single board. Can we rationalize a bit, and chose one configuration only (either NAND or MMC), for which we have the minimal and dev configurations?

I have in mind, but maybe I am wrong since the conversion is not recent, you told me having several defconfigs for the same board won't be an issue. The concern was more about having a dev_defconfig.

Without a defconfig targetted to NAND or MMC, the customer will have to recompile the at91bootstrap and u-boot, this is something we would like to avoid. I think u-boot case could be handled because the difference is mainly about environment variables. Concerning at91bootstrap, it is more complex. If you have any suggestion to handle this case and so reducing the number of defconfig variants, I would be happy.

Thanks

Ludovic

Quoted 7 lines

Thanks,

Thomas

Signature · 3 lines

Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Alexandre Belloni

2016-11-04 13:37 UTC #12 lore raw

PATCH 1/4 configs: at91sam9x5ek: add development rootfs

Quoted 31 lines · Ludovic Desroches

Quoted 19 lines · Thomas Petazzoni
Hello,
Quoted 9 lines · Ludovic Desroches
Add development rootfs based on linux4sam_5.4 for at91sam9x5ek for both NAND flash and SD card.
Signed-off-by Ludovic Desroches <[email protected]>
---
 board/atmel/at91sam9x5ek_mmc/genimage.cfg  |  34 ++++++++++
 board/atmel/at91sam9x5ek_mmc/post-image.sh |  20 ++++++
 configs/at91sam9x5ek_dev_defconfig         |  99 ++++++++++++++++++++++++++++
 configs/at91sam9x5ek_mmc_dev_defconfig     | 102 +++++++++++++++++++++++++++++
So after this patch, we would have:
at91sam9x5ek_defconfig
at91sam9x5ek_dev_defconfig
at91sam9x5ek_mmc_dev_defconfig
Quoted 6 lines
But no minimal MMC configuration.
That's a lot of configurations for a single board. Can we rationalize a bit, and chose one configuration only (either NAND or MMC), for which we have the minimal and dev configurations?
I have in mind, but maybe I am wrong since the conversion is not recent, you told me having several defconfigs for the same board won't be an issue. The concern was more about having a dev_defconfig.

Quoted 7 lines

Without a defconfig targetted to NAND or MMC, the customer will have to recompile the at91bootstrap and u-boot, this is something we would like to avoid. I think u-boot case could be handled because the difference is mainly about environment variables. Concerning at91bootstrap, it is more complex. If you have any suggestion to handle this case and so reducing the number of defconfig variants, I would be happy.

I think the best would be to be able to merge defconfigs. So, you'd get one iminimal defconfig per machine plus only one for the development image.

Signature · 3 lines

Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Thomas Petazzoni

2016-11-04 13:53 UTC #13 lore raw

PATCH 1/4 configs: at91sam9x5ek: add development rootfs

In reply to Ludovic Desroches

Hello,

Quoted 7 lines · Ludovic Desroches

Quoted 3 lines
That's a lot of configurations for a single board. Can we rationalize a bit, and chose one configuration only (either NAND or MMC), for which we have the minimal and dev configurations?
I have in mind, but maybe I am wrong since the conversion is not recent, you told me having several defconfigs for the same board won't be an issue. The concern was more about having a dev_defconfig.

Well, the issue is the overall multiplication of defconfigs, so both the fact that you have separate defconfigs for MMC and NAND, and the fact that you want to have those "dev_defconfig" contribute to the multiplication of defconfigs.

Quoted 6 lines

Without a defconfig targetted to NAND or MMC, the customer will have to recompile the at91bootstrap and u-boot, this is something we would like to avoid. I think u-boot case could be handled because the difference is mainly about environment variables. Concerning at91bootstrap, it is more complex. If you have any suggestion to handle this case and so reducing the number of defconfig variants, I would be happy.

Is it possible to have a single at91bootstrap for both the NAND and MMC scenarios? I guess you can decide depending on the boot source whether you should load u-boot from NAND or from MMC. However, this means you need to have both the NAND code and MMC code compiled in the same at91bootstrap image. Maybe this makes the at91bootstrap image too big? I'm not sure what are the constraints of the ROM code in terms of first stage bootloader size on this SoC.

Thomas

Signature · 3 lines

Thomas Petazzoni, CTO, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Ludovic Desroches

author

2016-11-04 16:28 UTC #14 lore raw

PATCH 1/4 configs: at91sam9x5ek: add development rootfs

Quoted 24 lines · Thomas Petazzoni

Hello,
Quoted 7 lines · Ludovic Desroches
Quoted 3 lines
That's a lot of configurations for a single board. Can we rationalize a bit, and chose one configuration only (either NAND or MMC), for which we have the minimal and dev configurations?
I have in mind, but maybe I am wrong since the conversion is not recent, you told me having several defconfigs for the same board won't be an issue. The concern was more about having a dev_defconfig.
Well, the issue is the overall multiplication of defconfigs, so both the fact that you have separate defconfigs for MMC and NAND, and the fact that you want to have those "dev_defconfig" contribute to the multiplication of defconfigs.
Quoted 6 lines
Without a defconfig targetted to NAND or MMC, the customer will have to recompile the at91bootstrap and u-boot, this is something we would like to avoid. I think u-boot case could be handled because the difference is mainly about environment variables. Concerning at91bootstrap, it is more complex. If you have any suggestion to handle this case and so reducing the number of defconfig variants, I would be happy.

Quoted 7 lines

Is it possible to have a single at91bootstrap for both the NAND and MMC scenarios? I guess you can decide depending on the boot source whether you should load u-boot from NAND or from MMC. However, this means you need to have both the NAND code and MMC code compiled in the same at91bootstrap image. Maybe this makes the at91bootstrap image too big? I'm not sure what are the constraints of the ROM code in terms of first stage bootloader size on this SoC.

No, it is not possible to get a single at91bootstrap to manage several boot medias. The boot media selection is an exclusive choice. Removing this constraint rises two potential issues:
- the size, we may have a binary too big as you said for some SoCs (only 24KB)
- we need to decide at execution time the boot media but we have no guarantee that all components are on the same media.

Ludovic

Thomas Petazzoni

2017-03-07 20:59 UTC #15 lore raw

PATCH 1/4 configs: at91sam9x5ek: add development rootfs

In reply to Ludovic Desroches

Hello,

Quoted 4 lines · Ludovic Desroches

Add development rootfs based on linux4sam_5.4 for at91sam9x5ek for both NAND flash and SD card.
Signed-off-by Ludovic Desroches <[email protected]>

Quoted 10 lines

---
 board/atmel/at91sam9x5ek_mmc/genimage.cfg  |  34 ++++++++++
 board/atmel/at91sam9x5ek_mmc/post-image.sh |  20 ++++++
 configs/at91sam9x5ek_dev_defconfig         |  99 ++++++++++++++++++++++++++++
 configs/at91sam9x5ek_mmc_dev_defconfig     | 102 +++++++++++++++++++++++++++++
 4 files changed, 255 insertions(+)
 create mode 100644 board/atmel/at91sam9x5ek_mmc/genimage.cfg
 create mode 100755 board/atmel/at91sam9x5ek_mmc/post-image.sh
 create mode 100644 configs/at91sam9x5ek_dev_defconfig
 create mode 100644 configs/at91sam9x5ek_mmc_dev_defconfig

In the end, I've applied your commit. But before doing so, I've added a at91sam9x5ek_mmc_defconfig, i.e a minimal defconfig for the MMC configuration.

Please check that everything is still OK on your side.

Thanks!

Thomas

Signature · 3 lines

Thomas Petazzoni, CTO, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

Ludovic Desroches

2017-03-08 07:22 UTC #16 lore raw

PATCH 1/4 configs: at91sam9x5ek: add development rootfs

Hi,

Quoted 18 lines · Thomas Petazzoni

Hello,

Quoted 4 lines · Ludovic Desroches

Add development rootfs based on linux4sam_5.4 for at91sam9x5ek for both NAND flash and SD card.
Signed-off-by Ludovic Desroches <[email protected]>

Quoted 10 lines

---
 board/atmel/at91sam9x5ek_mmc/genimage.cfg  |  34 ++++++++++
 board/atmel/at91sam9x5ek_mmc/post-image.sh |  20 ++++++
 configs/at91sam9x5ek_dev_defconfig         |  99 ++++++++++++++++++++++++++++
 configs/at91sam9x5ek_mmc_dev_defconfig     | 102 +++++++++++++++++++++++++++++
 4 files changed, 255 insertions(+)
 create mode 100644 board/atmel/at91sam9x5ek_mmc/genimage.cfg
 create mode 100755 board/atmel/at91sam9x5ek_mmc/post-image.sh
 create mode 100644 configs/at91sam9x5ek_dev_defconfig
 create mode 100644 configs/at91sam9x5ek_mmc_dev_defconfig

Quoted 3 lines

In the end, I've applied your commit. But before doing so, I've added a at91sam9x5ek_mmc_defconfig, i.e a minimal defconfig for the MMC configuration.

Thanks to add it, it is in line with defconfigs provided for other boards.

Quoted 3 lines

Please check that everything is still OK on your side.

We have not release a new version of linux4sam yet, so it's ok.

Thanks

Ludovic

Quoted 4 lines

Thanks!
Thomas