ARM: dts: imx7d-sdb: Add sht11 Click Board support
Subsystems (3)
PATCH 1/1 ARM: dts: imx7d-sdb: Add sht11 Click Board support
The imx7d-sdb has a mickro bus connector that can be connected to a Sensirion SHT11 click board (temperature and humidity sensor):
https://shop.mikroe.com/click/sensors/sht1x
Add a new device tree file to describe such hardware.
Signed-off-by Marco Franchi <[email protected]>
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx7d-sdb-sht11.dts | 74 +++++++++++++++++++++++++++++++++++ 2 files changed, 75 insertions(+) create mode 100644 arch/arm/boot/dts/imx7d-sdb-sht11.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -458,6 +458,7 @@ dtb-$(CONFIG_SOC_IMX7D) += \ imx7d-nitrogen7.dtb \ imx7d-sbc-imx7.dtb \ imx7d-sdb.dtb \ + imx7d-sdb-sht11.dtb \ imx7s-colibri-eval-v3.dtb \ imx7s-warp.dtb dtb-$(CONFIG_SOC_LS1021A) += \
arch/arm/boot/dts/imx7d-sdb-sht11.dts new file +74 -0
74 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH 1/1 ARM: dts: imx7d-sdb: Add sht11 Click Board support
Quoted 77 lines · Marco Franchi
The imx7d-sdb has a mickro bus connector that can be connected to a Sensirion SHT11 click board (temperature and humidity sensor):
https://shop.mikroe.com/click/sensors/sht1x
Add a new device tree file to describe such hardware.
Signed-off-by Marco Franchi <[email protected]>--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx7d-sdb-sht11.dts | 74 +++++++++++++++++++++++++++++++++++ 2 files changed, 75 insertions(+) create mode 100644 arch/arm/boot/dts/imx7d-sdb-sht11.dtsarch/arm/boot/dts/Makefile +1
-0@@ -458,6 +458,7 @@ dtb-$(CONFIG_SOC_IMX7D) += \ imx7d-nitrogen7.dtb \ imx7d-sbc-imx7.dtb \ imx7d-sdb.dtb \ + imx7d-sdb-sht11.dtb \ imx7s-colibri-eval-v3.dtb \ imx7s-warp.dtb dtb-$(CONFIG_SOC_LS1021A) += \arch/arm/boot/dts/imx7d-sdb-sht11.dts new file +45
-0@@ -0,0 +1,74 @@ +/* + * Copyright (C) 2015 Freescale Semiconductor, Inc. + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "imx7d-sdb.dts" + +/ {
arch/arm/boot/dts/imx7d-sdb-sht11.dts line 55
Quoted 10 lines
arch/arm/boot/dts/imx7d-sdb-sht11.dts new file +10
-0+ sensor { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sensor>; + compatible = "sensirion,sht15"; + clk-gpios = <&gpio4 12 0>; + data-gpios = <&gpio4 13 0>; + vcc-supply = <®_sht15>; + }; + + reg_sht15: reg-sht15 {
'regulator-sht15' should be the recommended name.
I fixed it up and applied the patch.
Shawn
Quoted 27 lines
arch/arm/boot/dts/imx7d-sdb-sht11.dts new file +19
-0+ compatible = "regulator-fixed"; + regulator-name = "reg_sht15"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&i2c3 { + status = "disabled"; +}; + +&iomuxc { + pinctrl_sensor: sensorgrp { + fsl,pins = < + MX7D_PAD_I2C3_SDA__GPIO4_IO13 0x4000007f + MX7D_PAD_I2C3_SCL__GPIO4_IO12 0x4000007f + >; + }; +};Signature · 7 lines
2.7.4 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel at lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel