Documentation: dt-bindings: Document bindings for Aspeed ADC
Subsystems (4)
PATCH v3 1/2 Documentation: dt-bindings: Document bindings for Aspeed ADC
---
Changes in v3:
- Consistently write hex contstants with lowercase letters
- Drop model numbers from description as same IP is used in every generation
Changes in v2:
- Rewritten as an IIO ADC device
.../devicetree/bindings/iio/adc/aspeed_adc.txt | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/adc/aspeed_adc.txt
Documentation/devicetree/bindings/iio/adc/aspeed_adc.txt new file +20 -0
@@ -0,0 +1,20 @@ +Aspeed ADC + +This device is a 10-bit converter for 16 voltage channels. All inputs are +single ended. + +Required properties: +- compatible: Should be "aspeed,ast2400-adc" or "aspeed,ast2500-adc" +- reg: memory window mapping address and length +- clocks: Input clock used to derive the sample clock. Expected to be the + SoC's APB clock. +- #io-channel-cells: Must be set to <1> to indicate channels are selected + by index. + +Example: + adc@1e6e9000 { + compatible = "aspeed,ast2400-adc"; + reg = <0x1e6e9000 0xb0>; + clocks = <&clk_apb>; + #io-channel-cells = <1>; + };
Signature · 1 line
2.12.1.500.gab5fba24ee-goog
PATCH v3 2/2 iio: Aspeed ADC
Aspeed BMC SoCs include a 16 channel, 10-bit ADC. Low and high threshold interrupts are supported by the hardware but are not currently implemented.
---
Changes in v3:
- Drop model numbers from description as same IP is used in every generation
- Remove unused macros
- Shorten macro prefix to just ASPEED_
- Remove extraneous whitespace
- Rename 2nd argument of ASPEED_CHAN() to clarify purpose
- Use existing macros in place of magic constants
- Remove unnecessary logging in failure conditions during probe
- Disable ADC hardware during remove()
- Add a NULL terminator to of_match_table
- Add per-model data to accomodate slight variations (vref, min/max sample rate)
- Added missing Kconfig depends on COMMON_CLK
Changes in v2:
- Rewritten as an IIO device
- Renamed register macros to describe the register's purpose
- Replaced awkward reading of 16-bit data registers with readw()
- Added Kconfig dependency on COMPILE_TEST
drivers/iio/adc/Kconfig | 11 ++ drivers/iio/adc/Makefile | 1 + drivers/iio/adc/aspeed_adc.c | 285 +++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 297 insertions(+) create mode 100644 drivers/iio/adc/aspeed_adc.c
drivers/iio/adc/Kconfig +11 -0
@@ -130,6 +130,17 @@ config AD799X To compile this driver as a module, choose M here: the module will be called ad799x. +config ASPEED_ADC + tristate "Aspeed ADC" + depends on ARCH_ASPEED || COMPILE_TEST + depends on COMMON_CLK + help + If you say yes here you get support for the ADC included in Aspeed + BMC SoCs. + + To compile this driver as a module, choose M here: the module will be + called aspeed_adc. + config AT91_ADC tristate "Atmel AT91 ADC" depends on ARCH_AT91
drivers/iio/adc/Makefile +1 -0
@@ -14,6 +14,7 @@ obj-$(CONFIG_AD7791) += ad7791.o obj-$(CONFIG_AD7793) += ad7793.o obj-$(CONFIG_AD7887) += ad7887.o obj-$(CONFIG_AD799X) += ad799x.o +obj-$(CONFIG_ASPEED_ADC) += aspeed_adc.o obj-$(CONFIG_AT91_ADC) += at91_adc.o obj-$(CONFIG_AT91_SAMA5D2_ADC) += at91-sama5d2_adc.o obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
drivers/iio/adc/aspeed_adc.c new file +285 -0
285 lines not on this page · raw message
Signature · 1 line
2.12.1.500.gab5fba24ee-goog