ARM: dts: imx6: add ZII RDU2 boards
Subsystems (3)
PATCH v3 1/1 ARM: dts: imx6: add ZII RDU2 boards
This adds support for the Zodiac Inflight Innovations RDU2 board, which has both a Quad and a QuadPlus variant.
The board supports different panels, with the bootloader patching in the correct compatible, depending on the hardware configuration.
---
v2: correct touchscreen IRQ to level low.
v3: changes to incorporate Shawns review
--- arch/arm/boot/dts/Makefile | 4 +- arch/arm/boot/dts/imx6q-zii-rdu2.dts | 50 ++ arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 934 ++++++++++++++++++++++++++++++++ arch/arm/boot/dts/imx6qp-zii-rdu2.dts | 50 ++ 4 files changed, 1037 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/imx6q-zii-rdu2.dts create mode 100644 arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi create mode 100644 arch/arm/boot/dts/imx6qp-zii-rdu2.dts
arch/arm/boot/dts/Makefile +3 -1
@@ -425,9 +425,11 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-utilite-pro.dtb \ imx6q-wandboard.dtb \ imx6q-wandboard-revb1.dtb \ + imx6q-zii-rdu2.dtb \ imx6qp-nitrogen6_max.dtb \ imx6qp-sabreauto.dtb \ - imx6qp-sabresd.dtb + imx6qp-sabresd.dtb \ + imx6qp-zii-rdu2.dtb dtb-$(CONFIG_SOC_IMX6SL) += \ imx6sl-evk.dtb \ imx6sl-warp.dtb
arch/arm/boot/dts/imx6q-zii-rdu2.dts new file +50 -0
50 lines not on this page · raw message
arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi new file +934 -0
934 lines not on this page · raw message
arch/arm/boot/dts/imx6qp-zii-rdu2.dts new file +50 -0
50 lines not on this page · raw message
Signature · 1 line
2.11.0
PATCH v3 1/1 ARM: dts: imx6: add ZII RDU2 boards
Quoted 10 lines · Lucas Stach
This adds support for the Zodiac Inflight Innovations RDU2 board, which has both a Quad and a QuadPlus variant.
The board supports different panels, with the bootloader patching in the correct compatible, depending on the hardware configuration.
Signed-off-by Philipp Zabel <[email protected]>Signed-off-by Lucas Stach <[email protected]>Tested-by Nikita Yushchenko <[email protected]>Tested-by Chris Healy <[email protected]>
I applied it with a couple of small fix-up below.
<snip>
Review
Quoted 3 lines
+&sata {
(quoted diff) +2
-0+ status = "okay"; + target-supply = <®_3p3v_ssd>;
To keep it consistency with other nodes, I switched these two lines.
Quoted 1 line
+};
<snip>
Review
Quoted 2 lines
+&iomuxc {
(quoted diff) +1
-0+ pinctrl-names = "default";
There is no point to have this when we do not have pinctrl-0 thing, so I dropped it.
Shawn
Quoted 7 lines
arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi new file +7
-0+ + pinctrl_accel: accelgrp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__GPIO1_IO18 0x4001b000 + MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x4001b000 + >; + };