rpi-config: waveshare screen support

Add support for the Waveshare 1024x600 "C" Rev2.1 7" IPS Capacitive Touch Screen LCD with HDMI interface:

	http://www.waveshare.com/7inch-HDMI-LCD-C.htm
	http://www.waveshare.com/wiki/7inch_HDMI_LCD_(C)

This product works "out of the box" with the Raspberry Pi. Simply connect the provided HDMI and USB cables between the two devices. The touch<=>mouse integration works automatically.

Tested with a Raspberry Pi 3, with a 32-bit raspberrypi3 build.

Signed-off-by Trevor Woerner <[email protected]>

---
 README                                  | 13 ++++++++++---
 recipes-bsp/bootfiles/rpi-config_git.bb | 10 ++++++++++
 2 files changed, 20 insertions(+), 3 deletions(-)

README +10 -3

index 65a1e5f..c58bc99 100644
@@ -29,7 +29,8 @@ Contents:
     3.L. Enable SPI bus
     3.M. Enable I2C
     3.N. Enable PiTFT support
-    3.O. Enable UART support
+    3.O. Misc. display
+    3.P. Enable UART support
 4. Extra apps
     4.A. omxplayer
 5. Board Configuration

@@ -241,9 +242,15 @@ List of currently supported models:
     - pitft22
     - pitft28r
 
-3.O. Enable UART
-===============
+3.O. Misc. display
+==================
+If you would like to use the Waveshare "C" 1024×600, 7 inch Capacitive Touch
+Screen LCD, HDMI interface (http://www.waveshare.com/7inch-HDMI-LCD-C.htm)
+Rev 2.1, please set the following in your local.conf
+WAVESHARE_1024X600_C_2.1 = "1"
 
+3.P. Enable UART
+===============
 RaspberryPi 1, 2 and CM will have UART console enabled by default.
 
 RaspberryPi 3 does not have the UART enabled by default because this needs a

recipes-bsp/bootfiles/rpi-config_git.bb +10 -1

index 20ec343..8adc938 100644
@@ -110,6 +110,16 @@ do_deploy() {
         echo "# Enable VC4 Graphics" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
         echo "dtoverlay=vc4-kms-v3d,${VC4_CMA_SIZE}" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
     fi
+
+    # Waveshare "C" 1024x600 7" Rev2.1 IPS capacitive touch (http://www.waveshare.com/7inch-HDMI-LCD-C.htm)
+    if [ "${WAVESHARE_1024X600_C_2.1}" = "1" ]; then
+        echo "# Waveshare \"C\" 1024x600 7\" Rev2.1 IPS capacitive touch screen" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+        echo "max_usb_current=1" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+        echo "hdmi_group=2" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+        echo "hdmi_mode=87" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+        echo "hdmi_cvt 1024 600 60 6 0 0 0" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+        echo "hdmi_drive=1" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+    fi
 }
 
 do_deploy_append_raspberrypi3-64() {
--

2.12.0.rc1.48.g076c053

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

Add support for the Waveshare 1024x600 "C" Rev2.1 7" IPS Capacitive Touch Screen LCD with HDMI interface:

        http://www.waveshare.com/7inch-HDMI-LCD-C.htm
        http://www.waveshare.com/wiki/7inch_HDMI_LCD_(C)

This product works "out of the box" with the Raspberry Pi. Simply connect the provided HDMI and USB cables between the two devices. The touch<=>mouse integration works automatically.

Tested with a Raspberry Pi 3, with a 32-bit raspberrypi3 build.

Signed-off-by Trevor Woerner <[email protected]>

---
 README                                  | 13 ++++++++++---
 recipes-bsp/bootfiles/rpi-config_git.bb | 10 ++++++++++
 2 files changed, 20 insertions(+), 3 deletions(-)

README +5 -3

index 65a1e5f..c58bc99 100644
@@ -29,7 +29,8 @@ Contents:
     3.L. Enable SPI bus
     3.M. Enable I2C
     3.N. Enable PiTFT support
-    3.O. Enable UART support
+    3.O. Misc. display
+    3.P. Enable UART support
 4. Extra apps
     4.A. omxplayer
 5. Board Configuration

@@ -241,9 +242,15 @@ List of currently supported models:
     - pitft22
     - pitft28r
 
-3.O. Enable UART
-===============
+3.O. Misc. display
+==================
+If you would like to use the Waveshare "C" 1024×600, 7 inch Capacitive

Touch
+Screen LCD, HDMI interface (http://www.waveshare.com/7inch-HDMI-LCD-C.htm
)

README +4 -0

+Rev 2.1, please set the following in your local.conf
+WAVESHARE_1024X600_C_2.1 = "1"
 
+3.P. Enable UART
+===============
 RaspberryPi 1, 2 and CM will have UART console enabled by default.
 
 RaspberryPi 3 does not have the UART enabled by default because this

needs a

recipes-bsp/bootfiles/rpi-config_git.bb +0 -0

index 20ec343..8adc938 100644
@@ -110,6 +110,16 @@ do_deploy() {
         echo "# Enable VC4 Graphics" >> ${DEPLOYDIR}/bcm2835-

bootfiles/config.txt

         echo "dtoverlay=vc4-kms-v3d,${VC4_CMA_SIZE}" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt
fi

recipes-bsp/bootfiles/rpi-config_git.bb +2 -0

+
+    # Waveshare "C" 1024x600 7" Rev2.1 IPS capacitive touch (

http://www.waveshare.com/7inch-HDMI-LCD-C.htm)

recipes-bsp/bootfiles/rpi-config_git.bb +2 -0

+    if [ "${WAVESHARE_1024X600_C_2.1}" = "1" ]; then
+        echo "# Waveshare \"C\" 1024x600 7\" Rev2.1 IPS capacitive touch

screen" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "max_usb_current=1" >> ${DEPLOYDIR}/bcm2835-
bootfiles/config.txt

recipes-bsp/bootfiles/rpi-config_git.bb +3 -0

+        echo "hdmi_group=2" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+        echo "hdmi_mode=87" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+        echo "hdmi_cvt 1024 600 60 6 0 0 0" >> ${DEPLOYDIR}/bcm2835-

bootfiles/config.txt

recipes-bsp/bootfiles/rpi-config_git.bb +2 -1

+        echo "hdmi_drive=1" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+    fi
 }
 
 do_deploy_append_raspberrypi3-64() {
--

2.12.0.rc1.48.g076c053

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

Quoted 1 line · Trevor Woerner

Add support for the Waveshare 1024x600 "C" Rev2.1 7" IPS Capacitive

Touch

Quoted 6 lines

Screen LCD with HDMI interface:

        http://www.waveshare.com/7inch-HDMI-LCD-C.htm
        http://www.waveshare.com/wiki/7inch_HDMI_LCD_(C)

This product works "out of the box" with the Raspberry Pi. Simply

connect

Quoted 1 line

the provided HDMI and USB cables between the two devices. The

touch<=>mouse

Quoted 25 lines

integration works automatically.

Tested with a Raspberry Pi 3, with a 32-bit raspberrypi3 build.

Signed-off-by Trevor Woerner <[email protected]>

---
 README                                  | 13 ++++++++++---
 recipes-bsp/bootfiles/rpi-config_git.bb | 10 ++++++++++
 2 files changed, 20 insertions(+), 3 deletions(-)

README +2 -1

index 65a1e5f..c58bc99 100644
@@ -29,7 +29,8 @@ Contents:
     3.L. Enable SPI bus
     3.M. Enable I2C
     3.N. Enable PiTFT support
-    3.O. Enable UART support
+    3.O. Misc. display
+    3.P. Enable UART support
 4. Extra apps
     4.A. omxplayer
 5. Board Configuration

README List of currently supported models: · line 247

Quoted 8 lines

README +3 -2

@@ -241,9 +242,15 @@ List of currently supported models:
     - pitft22
     - pitft28r
 
-3.O. Enable UART
-===============
+3.O. Misc. display
+==================
+If you would like to use the Waveshare "C" 1024×600, 7 inch

Capacitive

Quoted 2 lines

Touch
+Screen LCD, HDMI interface

(http://www.waveshare.com/7inch-HDMI-LCD-C.htm

Quoted 24 lines

)

README +4 -0

+Rev 2.1, please set the following in your local.conf
+WAVESHARE_1024X600_C_2.1 = "1"
 
+3.P. Enable UART
+===============
 RaspberryPi 1, 2 and CM will have UART console enabled by default.
 
 RaspberryPi 3 does not have the UART enabled by default because this

needs a

recipes-bsp/bootfiles/rpi-config_git.bb +0 -0

index 20ec343..8adc938 100644
@@ -110,6 +110,16 @@ do_deploy() {
         echo "# Enable VC4 Graphics" >> ${DEPLOYDIR}/bcm2835-

bootfiles/config.txt

         echo "dtoverlay=vc4-kms-v3d,${VC4_CMA_SIZE}" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt
fi

recipes-bsp/bootfiles/rpi-config_git.bb +2 -0

+
+    # Waveshare "C" 1024x600 7" Rev2.1 IPS capacitive touch (

http://www.waveshare.com/7inch-HDMI-LCD-C.htm)

recipes-bsp/bootfiles/rpi-config_git.bb

Quoted 2 lines

recipes-bsp/bootfiles/rpi-config_git.bb +2 -0

+    if [ "${WAVESHARE_1024X600_C_2.1}" = "1" ]; then
+        echo "# Waveshare \"C\" 1024x600 7\" Rev2.1 IPS capacitive

touch

Quoted 4 lines

screen" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "max_usb_current=1" >> ${DEPLOYDIR}/bcm2835-
bootfiles/config.txt
+ echo "hdmi_group=2" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 1 line

+ echo "hdmi_mode=87" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 3 lines

+ echo "hdmi_cvt 1024 600 60 6 0 0 0" >> ${DEPLOYDIR}/bcm2835-
bootfiles/config.txt
+ echo "hdmi_drive=1" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 7 lines

+ fi
}

do_deploy_append_raspberrypi3-64() {
--
2.12.0.rc1.48.g076c053

Quoted 6 lines

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

After applying this commit the build fails with:

ERROR: rpi-config-git-r5 do_deploy: Function failed: do_deploy (log
file is
located at /home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/log.do_deploy.32154)
ERROR: Logfile of failure stored in:
/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/log.do_deploy.32154 Log data follows:
| DEBUG: Executing python function sstate_task_prefunc
| DEBUG: Removing manifest:
/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/deploy/images/raspberrypi3/bcm2835-bootfiles/config.txt | DEBUG: Removing manifest:
/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/deploy/images/raspberrypi3/bcm2835-bootfiles/

| DEBUG: Python function sstate_task_prefunc finished
| DEBUG: Executing shell function do_deploy
|

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/run.do_deploy.32154:
192:
/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/run.do_deploy.32154:
Bad substitution
| WARNING: exit code 2 from a shell command.
| ERROR: Function failed: do_deploy (log file is located at /home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/log.do_deploy.32154)
ERROR: Task (/home/gizero/work/smartliving/distro/repo-master/build-poky/conf/../../layers/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb:do_deploy) failed with exit code '1'
NOTE: Tasks Summary: Attempted 4857 tasks of which 4855 didn't need to
be
rerun and 1 failed.

Still to look at it closer... maybe related to some shell configuration on
my side?

Hi,

Quoted 104 lines · Andrea Galbusera

Quoted 1 line · Trevor Woerner

Add support for the Waveshare 1024x600 "C" Rev2.1 7" IPS Capacitive

Touch

Quoted 6 lines

Screen LCD with HDMI interface:

        http://www.waveshare.com/7inch-HDMI-LCD-C.htm
        http://www.waveshare.com/wiki/7inch_HDMI_LCD_(C)

This product works "out of the box" with the Raspberry Pi. Simply

connect

Quoted 1 line

the provided HDMI and USB cables between the two devices. The

touch<=>mouse

Quoted 25 lines

integration works automatically.

Tested with a Raspberry Pi 3, with a 32-bit raspberrypi3 build.

Signed-off-by Trevor Woerner <[email protected]>

---
 README                                  | 13 ++++++++++---
 recipes-bsp/bootfiles/rpi-config_git.bb | 10 ++++++++++
 2 files changed, 20 insertions(+), 3 deletions(-)

README +2 -1

index 65a1e5f..c58bc99 100644
@@ -29,7 +29,8 @@ Contents:
     3.L. Enable SPI bus
     3.M. Enable I2C
     3.N. Enable PiTFT support
-    3.O. Enable UART support
+    3.O. Misc. display
+    3.P. Enable UART support
 4. Extra apps
     4.A. omxplayer
 5. Board Configuration

README List of currently supported models: · line 247

Quoted 8 lines

README +3 -2

@@ -241,9 +242,15 @@ List of currently supported models:
     - pitft22
     - pitft28r
 
-3.O. Enable UART
-===============
+3.O. Misc. display
+==================
+If you would like to use the Waveshare "C" 1024×600, 7 inch

Capacitive

Quoted 2 lines

Touch
+Screen LCD, HDMI interface

(http://www.waveshare.com/7inch-HDMI-LCD-C.htm

Quoted 24 lines

)

README +4 -0

+Rev 2.1, please set the following in your local.conf
+WAVESHARE_1024X600_C_2.1 = "1"
 
+3.P. Enable UART
+===============
 RaspberryPi 1, 2 and CM will have UART console enabled by default.
 
 RaspberryPi 3 does not have the UART enabled by default because this

needs a

recipes-bsp/bootfiles/rpi-config_git.bb +0 -0

index 20ec343..8adc938 100644
@@ -110,6 +110,16 @@ do_deploy() {
         echo "# Enable VC4 Graphics" >> ${DEPLOYDIR}/bcm2835-

bootfiles/config.txt

         echo "dtoverlay=vc4-kms-v3d,${VC4_CMA_SIZE}" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt
fi

recipes-bsp/bootfiles/rpi-config_git.bb +2 -0

+
+    # Waveshare "C" 1024x600 7" Rev2.1 IPS capacitive touch (

http://www.waveshare.com/7inch-HDMI-LCD-C.htm)

recipes-bsp/bootfiles/rpi-config_git.bb

Quoted 2 lines

recipes-bsp/bootfiles/rpi-config_git.bb +2 -0

+    if [ "${WAVESHARE_1024X600_C_2.1}" = "1" ]; then
+        echo "# Waveshare \"C\" 1024x600 7\" Rev2.1 IPS capacitive

touch

Quoted 4 lines

screen" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "max_usb_current=1" >> ${DEPLOYDIR}/bcm2835-
bootfiles/config.txt
+ echo "hdmi_group=2" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 1 line

+ echo "hdmi_mode=87" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 3 lines

+ echo "hdmi_cvt 1024 600 60 6 0 0 0" >> ${DEPLOYDIR}/bcm2835-
bootfiles/config.txt
+ echo "hdmi_drive=1" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 7 lines

+ fi
}

do_deploy_append_raspberrypi3-64() {
--
2.12.0.rc1.48.g076c053

Quoted 6 lines

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

Quoted 6 lines

After applying this commit the build fails with:

ERROR: rpi-config-git-r5 do_deploy: Function failed: do_deploy (log file is
located at /home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/

raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/log.do_deploy.32154)

Quoted 2 lines

ERROR: Logfile of failure stored in:
/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/

raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/log.do_deploy.32154

Quoted 4 lines

Log data follows:
| DEBUG: Executing python function sstate_task_prefunc
| DEBUG: Removing manifest:
/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/deploy/

images/raspberrypi3/bcm2835-bootfiles/config.txt

Quoted 2 lines

| DEBUG: Removing manifest:
/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/deploy/

images/raspberrypi3/bcm2835-bootfiles/

Quoted 4 lines

| DEBUG: Python function sstate_task_prefunc finished
| DEBUG: Executing shell function do_deploy
|

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/

raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/run.do_deploy.32154:

Quoted 2 lines

192:
/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/

raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/run.do_deploy.32154:

Quoted 4 lines

Bad substitution
| WARNING: exit code 2 from a shell command.
| ERROR: Function failed: do_deploy (log file is located at /home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/

raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/log.do_deploy.32154)

Quoted 2 lines

ERROR: Task (/home/gizero/work/smartliving/distro/repo-master/build-poky/conf/../../

layers/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb:do_deploy)

Quoted 5 lines

failed with exit code '1'
NOTE: Tasks Summary: Attempted 4857 tasks of which 4855 didn't need to be
rerun and 1 failed.

Quoted 3 lines

Still to look at it closer... maybe related to some shell configuration on
my side?

That is strange. Do you get any additional information? Can't pick anything from the posted log.

Quoted 3 lines · Andrei Gherzan

Hi,

On 4 April 2017 09:48:32 BST, Andrea Galbusera <[email protected]>

Quoted 4 lines · wrote:

Quoted 4 lines

Quoted 1 line · Trevor Woerner

Add support for the Waveshare 1024x600 "C" Rev2.1 7" IPS

Capacitive

Quoted 46 lines

Quoted 46 lines

Touch

Quoted 6 lines

Screen LCD with HDMI interface:

        http://www.waveshare.com/7inch-HDMI-LCD-C.htm
        http://www.waveshare.com/wiki/7inch_HDMI_LCD_(C)

This product works "out of the box" with the Raspberry Pi. Simply

connect

Quoted 1 line

the provided HDMI and USB cables between the two devices. The

touch<=>mouse

Quoted 25 lines

integration works automatically.

Tested with a Raspberry Pi 3, with a 32-bit raspberrypi3 build.

Signed-off-by Trevor Woerner <[email protected]>

---
 README                                  | 13 ++++++++++---
 recipes-bsp/bootfiles/rpi-config_git.bb | 10 ++++++++++
 2 files changed, 20 insertions(+), 3 deletions(-)

README +2 -1

index 65a1e5f..c58bc99 100644
@@ -29,7 +29,8 @@ Contents:
     3.L. Enable SPI bus
     3.M. Enable I2C
     3.N. Enable PiTFT support
-    3.O. Enable UART support
+    3.O. Misc. display
+    3.P. Enable UART support
 4. Extra apps
     4.A. omxplayer
 5. Board Configuration

README List of currently supported models: · line 247

Quoted 8 lines

README +3 -2

@@ -241,9 +242,15 @@ List of currently supported models:
     - pitft22
     - pitft28r
 
-3.O. Enable UART
-===============
+3.O. Misc. display
+==================
+If you would like to use the Waveshare "C" 1024×600, 7 inch

Capacitive

Quoted 2 lines

Touch
+Screen LCD, HDMI interface

Quoted 8 lines

Quoted 8 lines

(http://www.waveshare.com/7inch-HDMI-LCD-C.htm

README List of currently supported models:

Quoted 7 lines

)

README +4 -0

+Rev 2.1, please set the following in your local.conf
+WAVESHARE_1024X600_C_2.1 = "1"
 
+3.P. Enable UART
+===============
 RaspberryPi 1, 2 and CM will have UART console enabled by

default.

Quoted 2 lines

Quoted 2 lines

Quoted 2 lines

RaspberryPi 3 does not have the UART enabled by default because

this

Quoted 9 lines

Quoted 9 lines

Quoted 9 lines

needs a

recipes-bsp/bootfiles/rpi-config_git.bb +0 -0

index 20ec343..8adc938 100644
@@ -110,6 +110,16 @@ do_deploy() {
         echo "# Enable VC4 Graphics" >> ${DEPLOYDIR}/bcm2835-

bootfiles/config.txt

Quoted 8 lines

Quoted 8 lines

recipes-bsp/bootfiles/rpi-config_git.bb

Quoted 8 lines

         echo "dtoverlay=vc4-kms-v3d,${VC4_CMA_SIZE}" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt
fi

recipes-bsp/bootfiles/rpi-config_git.bb +2 -0

+
+    # Waveshare "C" 1024x600 7" Rev2.1 IPS capacitive touch (

http://www.waveshare.com/7inch-HDMI-LCD-C.htm)

recipes-bsp/bootfiles/rpi-config_git.bb +2 -0

+    if [ "${WAVESHARE_1024X600_C_2.1}" = "1" ]; then
+        echo "# Waveshare \"C\" 1024x600 7\" Rev2.1 IPS

capacitive

Quoted 9 lines

Quoted 9 lines

touch

Quoted 4 lines

screen" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "max_usb_current=1" >> ${DEPLOYDIR}/bcm2835-
bootfiles/config.txt
+ echo "hdmi_group=2" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 1 line

+ echo "hdmi_mode=87" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 1 line

+ echo "hdmi_cvt 1024 600 60 6 0 0 0" >>

${DEPLOYDIR}/bcm2835-

Quoted 24 lines

Quoted 18 lines

Quoted 2 lines

bootfiles/config.txt
+ echo "hdmi_drive=1" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 7 lines

+ fi
}

do_deploy_append_raspberrypi3-64() {
--
2.12.0.rc1.48.g076c053

Quoted 6 lines

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

Quoted 5 lines

After applying this commit the build fails with:

ERROR: rpi-config-git-r5 do_deploy: Function failed: do_deploy (log file is
located at

Quoted 7 lines

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/ raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/log.do_deploy.32154)

Quoted 1 line

ERROR: Logfile of failure stored in:

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/

raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/log.do_deploy.32154

Quoted 26 lines

Quoted 3 lines

Log data follows:
| DEBUG: Executing python function sstate_task_prefunc | DEBUG: Removing manifest:

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/deploy/ images/raspberrypi3/bcm2835-bootfiles/config.txt

Quoted 1 line

| DEBUG: Removing manifest:

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/deploy/ images/raspberrypi3/bcm2835-bootfiles/

Quoted 3 lines

| DEBUG: Python function sstate_task_prefunc finished
| DEBUG: Executing shell function do_deploy
|

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/ raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/run.do_deploy.32154:

Quoted 1 line

192:

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/ raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/run.do_deploy.32154:

Quoted 3 lines

Bad substitution
| WARNING: exit code 2 from a shell command.
| ERROR: Function failed: do_deploy (log file is located at

Quoted 7 lines

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/ raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/log.do_deploy.32154)

Quoted 1 line

ERROR: Task

(/home/gizero/work/smartliving/distro/repo-master/build-poky/conf/../../

layers/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb:do_deploy)

Quoted 2 lines

Quoted 2 lines

failed with exit code '1'
NOTE: Tasks Summary: Attempted 4857 tasks of which 4855 didn't need

to

Quoted 4 lines

Quoted 4 lines

be
rerun and 1 failed.

Still to look at it closer... maybe related to some shell

configuration

Quoted 6 lines

Quoted 2 lines

on
my side?

That is strange. Do you get any additional information? Can't pick anything from the posted log.

I nailed it down to the the shell variable WAVESHARE_1024X600_C_2.1 that
the patch just introduced.

Quoting bash manpage:

name A word consisting only of alphanumeric characters and under‐
scores, and beginning with an alphabetic character or an under‐
score. Also referred to as an identifier.

Looks like a variable name cannot contain dots. Just replacing the offending '.' solves the issue.
If you agree I can send a patch that s/./_/

Strangely enough all may shells fail in evaluating the following statement.
Why don't you guys see the same behavior?

if [ "${WAVESHARE_1024X600_C_2.1}" = "1" ]; then echo "hello!"; fi

Quoted 193 lines · Andrea Galbusera

Quoted 3 lines · Andrei Gherzan

Hi,

On 4 April 2017 09:48:32 BST, Andrea Galbusera <[email protected]>

Quoted 4 lines · wrote:

Quoted 4 lines

Quoted 1 line · Trevor Woerner

Add support for the Waveshare 1024x600 "C" Rev2.1 7" IPS

Capacitive

Quoted 46 lines

Quoted 46 lines

Touch

Quoted 6 lines

Screen LCD with HDMI interface:

        http://www.waveshare.com/7inch-HDMI-LCD-C.htm
        http://www.waveshare.com/wiki/7inch_HDMI_LCD_(C)

This product works "out of the box" with the Raspberry Pi. Simply

connect

Quoted 1 line

the provided HDMI and USB cables between the two devices. The

touch<=>mouse

Quoted 25 lines

integration works automatically.

Tested with a Raspberry Pi 3, with a 32-bit raspberrypi3 build.

Signed-off-by Trevor Woerner <[email protected]>

---
 README                                  | 13 ++++++++++---
 recipes-bsp/bootfiles/rpi-config_git.bb | 10 ++++++++++
 2 files changed, 20 insertions(+), 3 deletions(-)

README +2 -1

index 65a1e5f..c58bc99 100644
@@ -29,7 +29,8 @@ Contents:
     3.L. Enable SPI bus
     3.M. Enable I2C
     3.N. Enable PiTFT support
-    3.O. Enable UART support
+    3.O. Misc. display
+    3.P. Enable UART support
 4. Extra apps
     4.A. omxplayer
 5. Board Configuration

README List of currently supported models: · line 247

Quoted 8 lines

README +3 -2

@@ -241,9 +242,15 @@ List of currently supported models:
     - pitft22
     - pitft28r
 
-3.O. Enable UART
-===============
+3.O. Misc. display
+==================
+If you would like to use the Waveshare "C" 1024×600, 7 inch

Capacitive

Quoted 2 lines

Touch
+Screen LCD, HDMI interface

Quoted 8 lines

Quoted 8 lines

(http://www.waveshare.com/7inch-HDMI-LCD-C.htm

README List of currently supported models:

Quoted 7 lines

)

README +4 -0

+Rev 2.1, please set the following in your local.conf
+WAVESHARE_1024X600_C_2.1 = "1"
 
+3.P. Enable UART
+===============
 RaspberryPi 1, 2 and CM will have UART console enabled by

default.

Quoted 2 lines

Quoted 2 lines

Quoted 2 lines

RaspberryPi 3 does not have the UART enabled by default because

this

Quoted 9 lines

Quoted 9 lines

Quoted 9 lines

needs a

recipes-bsp/bootfiles/rpi-config_git.bb +0 -0

index 20ec343..8adc938 100644
@@ -110,6 +110,16 @@ do_deploy() {
         echo "# Enable VC4 Graphics" >> ${DEPLOYDIR}/bcm2835-

bootfiles/config.txt

Quoted 8 lines

Quoted 8 lines

recipes-bsp/bootfiles/rpi-config_git.bb

Quoted 8 lines

         echo "dtoverlay=vc4-kms-v3d,${VC4_CMA_SIZE}" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt
fi

recipes-bsp/bootfiles/rpi-config_git.bb +2 -0

+
+    # Waveshare "C" 1024x600 7" Rev2.1 IPS capacitive touch (

http://www.waveshare.com/7inch-HDMI-LCD-C.htm)

recipes-bsp/bootfiles/rpi-config_git.bb +2 -0

+    if [ "${WAVESHARE_1024X600_C_2.1}" = "1" ]; then
+        echo "# Waveshare \"C\" 1024x600 7\" Rev2.1 IPS

capacitive

Quoted 9 lines

Quoted 9 lines

touch

Quoted 4 lines

screen" >> ${DEPLOYDIR}/bcm2835-bootfiles/config.txt
+ echo "max_usb_current=1" >> ${DEPLOYDIR}/bcm2835-
bootfiles/config.txt
+ echo "hdmi_group=2" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 1 line

+ echo "hdmi_mode=87" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 1 line

+ echo "hdmi_cvt 1024 600 60 6 0 0 0" >>

${DEPLOYDIR}/bcm2835-

Quoted 24 lines

Quoted 18 lines

Quoted 2 lines

bootfiles/config.txt
+ echo "hdmi_drive=1" >>

${DEPLOYDIR}/bcm2835-bootfiles/config.txt

Quoted 7 lines

+ fi
}

do_deploy_append_raspberrypi3-64() {
--
2.12.0.rc1.48.g076c053

Quoted 6 lines

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto

Quoted 5 lines

After applying this commit the build fails with:

ERROR: rpi-config-git-r5 do_deploy: Function failed: do_deploy (log file is
located at

Quoted 7 lines

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/ raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/log.do_deploy.32154)

Quoted 1 line

ERROR: Logfile of failure stored in:

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/

raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/temp/log.do_deploy.32154

Quoted 26 lines

Quoted 3 lines

Log data follows:
| DEBUG: Executing python function sstate_task_prefunc | DEBUG: Removing manifest:

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/deploy/ images/raspberrypi3/bcm2835-bootfiles/config.txt

Quoted 1 line

| DEBUG: Removing manifest:

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/deploy/ images/raspberrypi3/bcm2835-bootfiles/

Quoted 3 lines

| DEBUG: Python function sstate_task_prefunc finished
| DEBUG: Executing shell function do_deploy
|

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/ raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/run.do_deploy.32154:

Quoted 1 line

192:

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/ raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/run.do_deploy.32154:

Quoted 3 lines

Bad substitution
| WARNING: exit code 2 from a shell command.
| ERROR: Function failed: do_deploy (log file is located at

Quoted 7 lines

/home/gizero/work/smartliving/distro/repo-master/build-poky/tmp/work/ raspberrypi3-poky-linux-gnueabi/rpi-config/git-r5/ temp/log.do_deploy.32154)

Quoted 1 line

ERROR: Task

(/home/gizero/work/smartliving/distro/repo-master/build-poky/conf/../../

layers/meta-raspberrypi/recipes-bsp/bootfiles/rpi-config_git.bb:do_deploy)

Quoted 2 lines

Quoted 2 lines

failed with exit code '1'
NOTE: Tasks Summary: Attempted 4857 tasks of which 4855 didn't need

to

Quoted 4 lines

Quoted 4 lines

be
rerun and 1 failed.

Still to look at it closer... maybe related to some shell

configuration

Quoted 6 lines

Quoted 2 lines

on
my side?

That is strange. Do you get any additional information? Can't pick anything from the posted log.

I nailed it down to the the shell variable WAVESHARE_1024X600_C_2.1 that
the patch just introduced.

Quoting bash manpage:

name A word consisting only of alphanumeric characters and under‐
scores, and beginning with an alphabetic character or an under‐
score. Also referred to as an identifier.

Looks like a variable name cannot contain dots. Just replacing the offending '.' solves the issue.
If you agree I can send a patch that s/./_/

Quoted 5 lines

Strangely enough all may shells fail in evaluating the following statement.
Why don't you guys see the same behavior?

if [ "${WAVESHARE_1024X600_C_2.1}" = "1" ]; then echo "hello!"; fi

Right. Good catch. Fire a patch away. Thanks.

--
Andrei Gherzan
gpg: rsa4096/D4D94F67AD0E9640 | t: @agherzan

I see what happened... knowing that I needed those lines set, my bbappend didn't have the "if" line, it simply applied the lines without the check. The check was added when pushing upstream just in case somebody didn't want those lines in their config :-) I should have tested more extensively after adding the line.

Sorry!