ARM: dts: imx: add Gateworks Ventana GW5903 support
Subsystems (3)
PATCH 1/1 ARM: dts: imx: add Gateworks Ventana GW5903 support
The Gateworks Ventana GW5903 is a single-board computer based on the NXP IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* 4GiB DDR3 DRAM
* 32GB eMMC
* 1x microSD connector
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* Inertial Module
* uBlox EMMY-W1 (bluetooth/nfc/802.11ac)
--- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/imx6dl-gw5903.dts | 55 +++ arch/arm/boot/dts/imx6q-gw5903.dts | 55 +++ arch/arm/boot/dts/imx6qdl-gw5903.dtsi | 660 ++++++++++++++++++++++++++++++++++ 4 files changed, 772 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-gw5903.dts create mode 100644 arch/arm/boot/dts/imx6q-gw5903.dts create mode 100644 arch/arm/boot/dts/imx6qdl-gw5903.dtsi
arch/arm/boot/dts/Makefile +2 -0
@@ -352,6 +352,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-gw551x.dtb \ imx6dl-gw552x.dtb \ imx6dl-gw553x.dtb \ + imx6dl-gw5903.dtb \ imx6dl-gw5904.dtb \ imx6dl-hummingboard.dtb \ imx6dl-icore.dtb \
@@ -396,6 +397,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-gw551x.dtb \ imx6q-gw552x.dtb \ imx6q-gw553x.dtb \ + imx6q-gw5903.dtb \ imx6q-gw5904.dtb \ imx6q-h100.dtb \ imx6q-hummingboard.dtb \
arch/arm/boot/dts/imx6dl-gw5903.dts new file +55 -0
55 lines not on this page · raw message
arch/arm/boot/dts/imx6q-gw5903.dts new file +55 -0
55 lines not on this page · raw message
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +660 -0
660 lines not on this page · raw message
Signature · 1 line
2.7.4
PATCH 1/1 ARM: dts: imx: add Gateworks Ventana GW5903 support
Quoted 217 lines · Tim Harvey
The Gateworks Ventana GW5903 is a single-board computer based on the NXP IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* 4GiB DDR3 DRAM
* 32GB eMMC
* 1x microSD connector
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* Inertial Module
* uBlox EMMY-W1 (bluetooth/nfc/802.11ac)Signed-off-by Tim Harvey <[email protected]>--- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/imx6dl-gw5903.dts | 55 +++ arch/arm/boot/dts/imx6q-gw5903.dts | 55 +++ arch/arm/boot/dts/imx6qdl-gw5903.dtsi | 660 ++++++++++++++++++++++++++++++++++ 4 files changed, 772 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-gw5903.dts create mode 100644 arch/arm/boot/dts/imx6q-gw5903.dts create mode 100644 arch/arm/boot/dts/imx6qdl-gw5903.dtsiarch/arm/boot/dts/Makefile +2
-0@@ -352,6 +352,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-gw551x.dtb \ imx6dl-gw552x.dtb \ imx6dl-gw553x.dtb \ + imx6dl-gw5903.dtb \ imx6dl-gw5904.dtb \ imx6dl-hummingboard.dtb \ imx6dl-icore.dtb \@@ -396,6 +397,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-gw551x.dtb \ imx6q-gw552x.dtb \ imx6q-gw553x.dtb \ + imx6q-gw5903.dtb \ imx6q-gw5904.dtb \ imx6q-h100.dtb \ imx6q-hummingboard.dtb \arch/arm/boot/dts/imx6dl-gw5903.dts new file +55
-0@@ -0,0 +1,55 @@ +/* + * Copyright 2017 Gateworks Corporation + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this file; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-gw5903.dtsi" + +/ { + model = "Gateworks Ventana i.MX6 Duallite/Solo GW5903"; + compatible = "gw,imx6dl-gw5903", "gw,ventana", "fsl,imx6dl"; +};arch/arm/boot/dts/imx6q-gw5903.dts new file +55
-0@@ -0,0 +1,55 @@ +/* + * Copyright 2017 Gateworks Corporation + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this file; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include "imx6qdl-gw5903.dtsi" + +/ { + model = "Gateworks Ventana i.MX6 Dual/Quad GW5903"; + compatible = "gw,imx6q-gw5903", "gw,ventana", "fsl,imx6q"; +};arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +42
-0@@ -0,0 +1,660 @@ +/* + * Copyright 2017 Gateworks Corporation + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this file; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 52
Quoted 10 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +10
-0+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/gpio/gpio.h> + +/ { + chosen { + bootargs = "console=ttymxc1,115200";
stdout-path please.
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 59
Quoted 7 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +7
-0+ }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = < + 0 /*1 2 3 4 5 6*/ 7 8 9
Why are 1 ~ 6 commented out?
Quoted 8 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +8
-0+ 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 77
Quoted 10 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +10
-0+ 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <94>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>;
It configures GPIO6_IO14 ...
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 81
Quoted 4 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +4
-0+ + led0: user1 { + label = "user1"; + gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; /* MX6_LOCLED# */
... it use gpio6_11 however?
Quoted 55 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +55
-0+ default-state = "off"; + }; + }; + + memory { + reg = <0x10000000 0x40000000>; + }; + + reg_5p0v: regulator-5p0v { + compatible = "regulator-fixed"; + regulator-name = "5P0V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_2p5v: regulator-2p5v { + compatible = "regulator-fixed"; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_usb_h1_vbus: regulator-usb-h1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 30 0>; + enable-active-high; + }; + + reg_usb_otg_vbus: regulator-usb-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_12p0: regulator-12p0v { + compatible = "regulator-fixed"; + regulator-name = "12P0V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>;
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 146
Quoted 10 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +10
-0+ gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + sound { + compatible = "fsl,imx-audio-tlv320"; + model = "imx-tlv320"; + ssi-controller = <&ssi1>; + audio-codec = <&tlv320aic3105>; + /* routing of sink, soruce */
s/soruce/source?
Quoted 20 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +20
-0+ audio-routing = + /* TLV320 LINE1L pin <-> Mic Jack connector */ + "LINE1L", "Mic Jack", + /* board Headphone Jack <-> HPOUT */ + "Headphone Jack", "HPLOUT", + "Headphone Jack", "HPROUT", + "Mic Jack", "Mic Bias"; + mux-int-port = <1>; + mux-ext-port = <6>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 176
Quoted 10 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +10
-0+ <&clks IMX6QDL_CLK_LDB_DI1_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL3_USB_OTG>, + <&clks IMX6QDL_CLK_PLL3_USB_OTG>; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii-id"; + pinctrl-assert-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>; /* PHY_EN */
Unsupported bindings?
Quoted 131 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +131
-0+ status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pca9555: gpio at 23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + eeprom1: eeprom at 50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + eeprom2: eeprom at 51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + eeprom3: eeprom at 52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + }; + + eeprom4: eeprom at 53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; + + dts1672: rtc at 68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + ltc3676: pmic at 3c { + compatible = "lltc,ltc3676"; + reg = <0x3c>; + interrupt-parent = <&gpio1>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>; + + regulators { + /* VDD_1P8 (1+R1/R2 = 2.505): Aud/eMMC/microSD/Touch */ + reg_1p8v: sw1 { + regulator-name = "vdd1p8"; + regulator-min-microvolt = <1033310>; + regulator-max-microvolt = <2004000>; + lltc,fb-voltage-divider = <301000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + /* VDD_DDR (1+R1/R2 = 2.105) */ + reg_vdd_ddr: sw2 { + regulator-name = "vddddr"; + regulator-min-microvolt = <868310>; + regulator-max-microvolt = <1684000>; + lltc,fb-voltage-divider = <221000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + }; + + /* VDD_ARM (1+R1/R2 = 1.635) */ + reg_vdd_arm: sw3 { + regulator-name = "vddarm"; + regulator-min-microvolt = <674400>; + regulator-max-microvolt = <1308000>; + lltc,fb-voltage-divider = <127000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + linux,phandle = <®_vdd_arm>; + }; + + /* VDD_SOC (1+R1/R2 = 1.635) */ + reg_vdd_soc: sw4 { + regulator-name = "vddsoc"; + regulator-min-microvolt = <674400>; + regulator-max-microvolt = <1308000>; + lltc,fb-voltage-divider = <127000 200000>; + regulator-ramp-delay = <7000>; + regulator-boot-on; + regulator-always-on; + linux,phandle = <®_vdd_soc>; + }; + + /* VDD_1P0 (1+R1/R2 = 1.38): */ + reg_1p0v: ldo2 { + regulator-name = "vdd1p0"; + regulator-min-microvolt = <1002777>; + regulator-max-microvolt = <1002777>; + lltc,fb-voltage-divider = <100000 261000>; + regulator-boot-on; + regulator-always-on; + }; + + /* VDD_HIGH (1+R1/R2 = 4.17) */ + reg_3p0v: ldo4 { + regulator-name = "vdd3p0"; + regulator-min-microvolt = <3023250>; + regulator-max-microvolt = <3023250>; + lltc,fb-voltage-divider = <634000 200000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default";
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 317
Quoted 10 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +10
-0+ pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + tlv320aic3105: codec at 18 { + compatible = "ti,tlv320aic3x"; + reg = <0x18>; + gpio-reset = <&gpio5 17 GPIO_ACTIVE_LOW>; + clocks = <&clks IMX6QDL_CLK_CKO>; + ai3x-micbias-vg = <2>; /* MICBIAS_2_5V */ + status = "okay";
The okay status shouldn't be needed for this node.
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 318
Quoted 1 line
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +1
-0+
We do not usually have newlines in middle of property list.
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 327
Quoted 9 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +9
-0+ /* Regulators */ + DRVDD-supply = <®_3p3v>; + AVDD-supply = <®_3p3v>; + IOVDD-supply = <®_3p3v>; + DVDD-supply = <®_1p8v>; + }; + + /* accelerometer */ + mma8653fc at 1d {
Node name should probably be accelerometer, so that the comment above can be saved.
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 334
Quoted 7 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +7
-0+ compatible = "fsl,mma8451"; + reg = <0x1d>; + interrupt-parent = <&gpio7>; + interrupts = <11 IRQ_TYPE_EDGE_RISING>; + interrupt-route = <1>; + position = <7>; + vdd-supply = <®_3p3v>;
Quite a few property cannot be found in bindings/iio/accel/mma8452.txt.
arch/arm/boot/dts/imx6qdl-gw5903.dtsi line 345
Quoted 11 lines
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +11
-0+ }; + + /* headphone detect */ + ts3a227e at 3b { + compatible = "ti,ts3a227e"; + reg = <0x3b>; + interrupt-parent = <&gpio5>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + ti,micbias = <4>; /* 2.5V micbias */ + }; +};
Shawn
Rob Herring
maintainerPATCH 1/1 ARM: dts: imx: add Gateworks Ventana GW5903 support
In reply to Tim HarveyQuoted 89 lines · Tim Harvey
The Gateworks Ventana GW5903 is a single-board computer based on the NXP IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* 4GiB DDR3 DRAM
* 32GB eMMC
* 1x microSD connector
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* Inertial Module
* uBlox EMMY-W1 (bluetooth/nfc/802.11ac)Signed-off-by Tim Harvey <[email protected]>--- arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/imx6dl-gw5903.dts | 55 +++ arch/arm/boot/dts/imx6q-gw5903.dts | 55 +++ arch/arm/boot/dts/imx6qdl-gw5903.dtsi | 660 ++++++++++++++++++++++++++++++++++ 4 files changed, 772 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-gw5903.dts create mode 100644 arch/arm/boot/dts/imx6q-gw5903.dts create mode 100644 arch/arm/boot/dts/imx6qdl-gw5903.dtsiarch/arm/boot/dts/Makefile +2
-0@@ -352,6 +352,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-gw551x.dtb \ imx6dl-gw552x.dtb \ imx6dl-gw553x.dtb \ + imx6dl-gw5903.dtb \ imx6dl-gw5904.dtb \ imx6dl-hummingboard.dtb \ imx6dl-icore.dtb \@@ -396,6 +397,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-gw551x.dtb \ imx6q-gw552x.dtb \ imx6q-gw553x.dtb \ + imx6q-gw5903.dtb \ imx6q-gw5904.dtb \ imx6q-h100.dtb \ imx6q-hummingboard.dtb \arch/arm/boot/dts/imx6dl-gw5903.dts new file +36
-0@@ -0,0 +1,55 @@ +/* + * Copyright 2017 Gateworks Corporation + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this file; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software.
arch/arm/boot/dts/imx6dl-gw5903.dts line 46
Quoted 10 lines
arch/arm/boot/dts/imx6dl-gw5903.dts new file +10
-0+ * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */
You can use SPDX tag here:
SPDX-License-Identifier: (GPL-2.0+ OR MIT)
While it says X11, this is really MIT license text as defined by SPDX.
PATCH 1/1 ARM: dts: imx: add Gateworks Ventana GW5903 support
Quoted 55 lines · Rob Herring
Quoted 42 lines
arch/arm/boot/dts/imx6dl-gw5903.dts new file +36
-0@@ -0,0 +1,55 @@ +/* + * Copyright 2017 Gateworks Corporation + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public + * License along with this file; if not, write to the Free + * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, + * MA 02110-1301 USA + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software.arch/arm/boot/dts/imx6dl-gw5903.dts line 46
Quoted 10 lines
arch/arm/boot/dts/imx6dl-gw5903.dts new file +10
-0+ * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */You can use SPDX tag here:
Quoted 3 lines
SPDX-License-Identifier: (GPL-2.0+ OR MIT)
While it says X11, this is really MIT license text as defined by SPDX.
Isn't it still controversial whether we should use SPDX tag or not?
https://lkml.org/lkml/2017/2/28/750
Shawn
PATCH v2 1/1 ARM: dts: imx: add Gateworks Ventana GW5903 support
In reply to Tim HarveyThe Gateworks Ventana GW5903 is a single-board computer based on the NXP IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* 4GiB DDR3 DRAM
* 32GB eMMC
* 1x microSD connector
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* Inertial Module
* uBlox EMMY-W1 (bluetooth/nfc/802.11ac)
---
v2:
- use stdout-path
- un-comment various brightness levels
- fix led gpio
- fix typo in comment
- remove unsupported bindings
- removed unnecessary status binding from i2c device node
- removed newline in property list
- name accelerometer node
arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/imx6dl-gw5903.dts | 55 +++ arch/arm/boot/dts/imx6q-gw5903.dts | 55 +++ arch/arm/boot/dts/imx6qdl-gw5903.dtsi | 654 ++++++++++++++++++++++++++++++++++ 4 files changed, 766 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-gw5903.dts create mode 100644 arch/arm/boot/dts/imx6q-gw5903.dts create mode 100644 arch/arm/boot/dts/imx6qdl-gw5903.dtsi
arch/arm/boot/dts/Makefile +2 -0
@@ -352,6 +352,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-gw551x.dtb \ imx6dl-gw552x.dtb \ imx6dl-gw553x.dtb \ + imx6dl-gw5903.dtb \ imx6dl-gw5904.dtb \ imx6dl-hummingboard.dtb \ imx6dl-icore.dtb \
@@ -396,6 +397,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-gw551x.dtb \ imx6q-gw552x.dtb \ imx6q-gw553x.dtb \ + imx6q-gw5903.dtb \ imx6q-gw5904.dtb \ imx6q-h100.dtb \ imx6q-hummingboard.dtb \
arch/arm/boot/dts/imx6dl-gw5903.dts new file +55 -0
55 lines not on this page · raw message
arch/arm/boot/dts/imx6q-gw5903.dts new file +55 -0
55 lines not on this page · raw message
arch/arm/boot/dts/imx6qdl-gw5903.dtsi new file +654 -0
654 lines not on this page · raw message
Signature · 1 line
2.7.4
Shawn Guo
AppliedPATCH v2 1/1 ARM: dts: imx: add Gateworks Ventana GW5903 support
Quoted 16 lines · Tim Harvey
The Gateworks Ventana GW5903 is a single-board computer based on the NXP IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* 4GiB DDR3 DRAM
* 32GB eMMC
* 1x microSD connector
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* Inertial Module
* uBlox EMMY-W1 (bluetooth/nfc/802.11ac)
Quoted 1 line
Signed-off-by Tim Harvey <[email protected]>
Applied, thanks.