Kernel PSR Fix-ups
Subsystems (2)
cover Kernel PSR Fix-ups
These patches, along with an upcoming series for IGT, enable our PSR IGT tests to run reliably once again. The first change enables us to run the PSR tests on SKL and KBL RVP platforms, whose panels have too slow of a setup time when running in their preferred mode. The second fixes a minor problem with the way that we were initializing SRD_CTL that caused us to clobber a bit that we are not supposed to change in that register on SKL and KBL. The third change re-introduces some changes to our link training code to be less aggressive about changing link state for eDP, because PSR depends on the link state being the same at PSR exit as it was at PSR entry. The fourth change greatly increases the reliability of reading the sink CRC generated by the eDP panel.
Jim Bride (4):
drm/i915/edp: Allow alternate fixed mode for eDP if available. drm/i915/psr: Clean-up intel_enable_source_psr1() drm/i915/edp: Be less aggressive about changing link config on eDP drm/i915/psr: Account for sink CRC raciness on some panels
drivers/gpu/drm/i915/i915_debugfs.c | 14 +++- drivers/gpu/drm/i915/i915_reg.h | 4 ++ drivers/gpu/drm/i915/intel_dp.c | 95 +++++++++++++++++++++++---- drivers/gpu/drm/i915/intel_dp_link_training.c | 11 +++- drivers/gpu/drm/i915/intel_drv.h | 4 ++ drivers/gpu/drm/i915/intel_dsi.c | 2 +- drivers/gpu/drm/i915/intel_dvo.c | 2 +- drivers/gpu/drm/i915/intel_lvds.c | 3 +- drivers/gpu/drm/i915/intel_panel.c | 2 + drivers/gpu/drm/i915/intel_psr.c | 21 +++++- 10 files changed, 136 insertions(+), 22 deletions(-)
Signature · 6 lines
2.7.4 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 1/4 drm/i915/edp: Allow alternate fixed mode for eDP if available.
Some fixed resolution panels actually support more than one mode, with the only thing different being the refresh rate. Having this alternate mode available to us is desirable, because it allows us to test PSR on panels whose setup time at the preferred mode is too long. With this patch we allow the use of the alternate mode if it's available and it was specifically requested.
--- drivers/gpu/drm/i915/intel_dp.c | 34 +++++++++++++++++++++++++++++----- drivers/gpu/drm/i915/intel_drv.h | 2 ++ drivers/gpu/drm/i915/intel_dsi.c | 2 +- drivers/gpu/drm/i915/intel_dvo.c | 2 +- drivers/gpu/drm/i915/intel_lvds.c | 3 ++- drivers/gpu/drm/i915/intel_panel.c | 2 ++ 6 files changed, 37 insertions(+), 8 deletions(-)
drivers/gpu/drm/i915/intel_dp.c +29 -5
@@ -1637,6 +1637,19 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,return bpp; } +static bool intel_edp_compare_alt_mode (struct drm_display_mode *m1, +struct drm_display_mode *m2) +{ +return (m1->hdisplay == m2->hdisplay && + m1->hsync_start == m2->hsync_start && + m1->hsync_end == m2->hsync_end && + m1->htotal == m2->htotal && + m1->vdisplay == m2->vdisplay && + m1->vsync_start == m2->vsync_start && + m1->vsync_end == m2->vsync_end && + m1->vtotal == m2->vtotal); +} + bool intel_dp_compute_config(struct intel_encoder *encoder, struct intel_crtc_state *pipe_config,
@@ -1674,8 +1687,16 @@ intel_dp_compute_config(struct intel_encoder *encoder, pipe_config->has_audio = intel_dp->has_audio && port !=PORT_A ;if (is_edp (intel_dp) && intel_connector->panel.fixed_mode) { -intel_fixed_panel_mode (intel_connector->panel.fixed_mode, - adjusted_mode); +struct drm_display_mode *panel_mode = + intel_connector->panel.alt_fixed_mode; +struct drm_display_mode *req_mode = &pipe_config->base.mode; + +if (!intel_edp_compare_alt_mode (req_mode, panel_mode)) + panel_mode = intel_connector->panel.fixed_mode; + +drm_mode_debug_printmodeline (panel_mode); + +intel_fixed_panel_mode (panel_mode, adjusted_mode);if (INTEL_GEN (dev_priv) >=9 ) {int ret;
@@ -5829,6 +5850,7 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp,struct drm_device *dev = intel_encoder->base.dev;struct drm_i915_private *dev_priv =to_i915 (dev);struct drm_display_mode *fixed_mode =NULL ; +struct drm_display_mode *alt_fixed_mode =NULL ;struct drm_display_mode *downclock_mode =NULL ;bool has_dpcd;struct drm_display_mode *scan;
@@ -5884,13 +5906,14 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp, } intel_connector->edid = edid; -/* prefer fixed mode from EDID if available */ +/* prefer fixed mode from EDID if available, save an alt mode also */ list_for_each_entry (scan, &connector->probed_modes, head) {if ((scan->type &DRM_MODE_TYPE_PREFERRED )) { fixed_mode =drm_mode_duplicate (dev, scan); downclock_mode =intel_dp_drrs_init ( intel_connector, fixed_mode); -break ; + }else { + alt_fixed_mode =drm_mode_duplicate (dev, scan); } }
@@ -5927,7 +5950,8 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp, pipe_name(pipe)); } -intel_panel_init (&intel_connector->panel, fixed_mode, downclock_mode); +intel_panel_init (&intel_connector->panel, fixed_mode, alt_fixed_mode, + downclock_mode); intel_connector->panel.backlight.power = intel_edp_backlight_power;intel_panel_setup_backlight (connector, pipe);
drivers/gpu/drm/i915/intel_drv.h +2 -0
@@ -265,6 +265,7 @@ struct intel_encoder {struct intel_panel {struct drm_display_mode *fixed_mode; +struct drm_display_mode *alt_fixed_mode;struct drm_display_mode *downclock_mode;int fitting_mode;
@@ -1676,6 +1677,7 @@ void intel_overlay_reset(struct drm_i915_private *dev_priv);/* intel_panel.c */ int intel_panel_init (struct intel_panel *panel,struct drm_display_mode *fixed_mode, +struct drm_display_mode *alt_fixed_mode,struct drm_display_mode *downclock_mode);void intel_panel_fini (struct intel_panel *panel); void intel_fixed_panel_mode(const struct drm_display_mode *fixed_mode,
drivers/gpu/drm/i915/intel_dsi.c +1 -1
@@ -1852,7 +1852,7 @@ void intel_dsi_init(struct drm_i915_private *dev_priv) connector->display_info.width_mm = fixed_mode->width_mm; connector->display_info.height_mm = fixed_mode->height_mm; -intel_panel_init (&intel_connector->panel, fixed_mode,NULL ); +intel_panel_init (&intel_connector->panel, fixed_mode,NULL ,NULL );intel_panel_setup_backlight (connector,INVALID_PIPE );intel_dsi_add_properties (intel_connector);
drivers/gpu/drm/i915/intel_dvo.c +1 -1
@@ -554,7 +554,7 @@ void intel_dvo_init(struct drm_i915_private *dev_priv)*/ intel_panel_init (&intel_connector->panel,intel_dvo_get_current_mode (connector), -NULL ); +NULL ,NULL ); intel_dvo->panel_wants_dither = true; }
drivers/gpu/drm/i915/intel_lvds.c +2 -1
@@ -1181,7 +1181,8 @@ void intel_lvds_init(struct drm_i915_private *dev_priv) out:mutex_unlock (&dev->mode_config.mutex); -intel_panel_init (&intel_connector->panel, fixed_mode, downclock_mode); +intel_panel_init (&intel_connector->panel, fixed_mode,NULL , + downclock_mode);intel_panel_setup_backlight (connector,INVALID_PIPE ); lvds_encoder->is_dual_link =compute_is_dual_link_lvds (lvds_encoder);
drivers/gpu/drm/i915/intel_panel.c +2 -0
@@ -1801,11 +1801,13 @@ intel_panel_init_backlight_funcs(struct intel_panel *panel)int intel_panel_init (struct intel_panel *panel,struct drm_display_mode *fixed_mode, +struct drm_display_mode *alt_fixed_mode,struct drm_display_mode *downclock_mode) {intel_panel_init_backlight_funcs (panel); panel->fixed_mode = fixed_mode; + panel->alt_fixed_mode = alt_fixed_mode; panel->downclock_mode = downclock_mode;return 0 ;
Signature · 6 lines
2.7.4 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jani Nikula
maintainerRe: [PATCH 1/4] drm/i915/edp: Allow alternate fixed mode for eDP if available.
Quoted 6 lines · Jim Bride
Some fixed resolution panels actually support more than one mode, with the only thing different being the refresh rate. Having this alternate mode available to us is desirable, because it allows us to test PSR on panels whose setup time at the preferred mode is too long. With this patch we allow the use of the alternate mode if it's available and it was specifically requested.
All in all this feels like a hack. The generic solution would be to allow any mode to be set again.
A few specific comments inline.
BR,
Jani.
Quoted 22 lines
Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Jim Bride <[email protected]>--- drivers/gpu/drm/i915/intel_dp.c | 34 +++++++++++++++++++++++++++++----- drivers/gpu/drm/i915/intel_drv.h | 2 ++ drivers/gpu/drm/i915/intel_dsi.c | 2 +- drivers/gpu/drm/i915/intel_dvo.c | 2 +- drivers/gpu/drm/i915/intel_lvds.c | 3 ++- drivers/gpu/drm/i915/intel_panel.c | 2 ++ 6 files changed, 37 insertions(+), 8 deletions(-)drivers/gpu/drm/i915/intel_dp.c +2
-0@@ -1637,6 +1637,19 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,return bpp; } +static bool intel_edp_compare_alt_mode (struct drm_display_mode *m1, +struct drm_display_mode *m2)
drivers/gpu/drm/i915/intel_dp.c static int intel_dp_compute_bpp(struct intel_dp *intel_dp, · line 1651
Quoted 10 lines
drivers/gpu/drm/i915/intel_dp.c +10
-0+{ +return (m1->hdisplay == m2->hdisplay && + m1->hsync_start == m2->hsync_start && + m1->hsync_end == m2->hsync_end && + m1->htotal == m2->htotal && + m1->vdisplay == m2->vdisplay && + m1->vsync_start == m2->vsync_start && + m1->vsync_end == m2->vsync_end && + m1->vtotal == m2->vtotal); +}
See drm_mode_equal and friends.
Quoted 36 lines
drivers/gpu/drm/i915/intel_dp.c +12
-3+ bool intel_dp_compute_config(struct intel_encoder *encoder, struct intel_crtc_state *pipe_config,@@ -1674,8 +1687,16 @@ intel_dp_compute_config(struct intel_encoder *encoder, pipe_config->has_audio = intel_dp->has_audio && port !=PORT_A ;if (is_edp (intel_dp) && intel_connector->panel.fixed_mode) { -intel_fixed_panel_mode (intel_connector->panel.fixed_mode, - adjusted_mode); +struct drm_display_mode *panel_mode = + intel_connector->panel.alt_fixed_mode; +struct drm_display_mode *req_mode = &pipe_config->base.mode; + +if (!intel_edp_compare_alt_mode (req_mode, panel_mode)) + panel_mode = intel_connector->panel.fixed_mode; + +drm_mode_debug_printmodeline (panel_mode); + +intel_fixed_panel_mode (panel_mode, adjusted_mode);if (INTEL_GEN (dev_priv) >=9 ) {int ret;@@ -5829,6 +5850,7 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp,struct drm_device *dev = intel_encoder->base.dev;struct drm_i915_private *dev_priv =to_i915 (dev);struct drm_display_mode *fixed_mode =NULL ; +struct drm_display_mode *alt_fixed_mode =NULL ;struct drm_display_mode *downclock_mode =NULL ;bool has_dpcd;struct drm_display_mode *scan;@@ -5884,13 +5906,14 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp, } intel_connector->edid = edid; -/* prefer fixed mode from EDID if available */
drivers/gpu/drm/i915/intel_dp.c static bool intel_edp_init_connector(struct intel_dp *intel_dp, · line 5917
Quoted 10 lines
drivers/gpu/drm/i915/intel_dp.c +3
-1+/* prefer fixed mode from EDID if available, save an alt mode also */ list_for_each_entry (scan, &connector->probed_modes, head) {if ((scan->type &DRM_MODE_TYPE_PREFERRED )) { fixed_mode =drm_mode_duplicate (dev, scan); downclock_mode =intel_dp_drrs_init ( intel_connector, fixed_mode); -break ; + }else { + alt_fixed_mode =drm_mode_duplicate (dev, scan); }
This changes the fixed mode if there are more than one preferred mode. This will also leak all but the two modes.
Quoted 90 lines
drivers/gpu/drm/i915/intel_dp.c +2
-1}@@ -5927,7 +5950,8 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp, pipe_name(pipe)); } -intel_panel_init (&intel_connector->panel, fixed_mode, downclock_mode); +intel_panel_init (&intel_connector->panel, fixed_mode, alt_fixed_mode, + downclock_mode); intel_connector->panel.backlight.power = intel_edp_backlight_power;intel_panel_setup_backlight (connector, pipe);drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -265,6 +265,7 @@ struct intel_encoder {struct intel_panel {struct drm_display_mode *fixed_mode; +struct drm_display_mode *alt_fixed_mode;struct drm_display_mode *downclock_mode;int fitting_mode;@@ -1676,6 +1677,7 @@ void intel_overlay_reset(struct drm_i915_private *dev_priv);/* intel_panel.c */ int intel_panel_init (struct intel_panel *panel,struct drm_display_mode *fixed_mode, +struct drm_display_mode *alt_fixed_mode,struct drm_display_mode *downclock_mode);void intel_panel_fini (struct intel_panel *panel); void intel_fixed_panel_mode(const struct drm_display_mode *fixed_mode,drivers/gpu/drm/i915/intel_dsi.c +1
-1@@ -1852,7 +1852,7 @@ void intel_dsi_init(struct drm_i915_private *dev_priv) connector->display_info.width_mm = fixed_mode->width_mm; connector->display_info.height_mm = fixed_mode->height_mm; -intel_panel_init (&intel_connector->panel, fixed_mode,NULL ); +intel_panel_init (&intel_connector->panel, fixed_mode,NULL ,NULL );intel_panel_setup_backlight (connector,INVALID_PIPE );intel_dsi_add_properties (intel_connector);drivers/gpu/drm/i915/intel_dvo.c +1
-1@@ -554,7 +554,7 @@ void intel_dvo_init(struct drm_i915_private *dev_priv)*/ intel_panel_init (&intel_connector->panel,intel_dvo_get_current_mode (connector), -NULL ); +NULL ,NULL ); intel_dvo->panel_wants_dither = true; }drivers/gpu/drm/i915/intel_lvds.c +2
-1@@ -1181,7 +1181,8 @@ void intel_lvds_init(struct drm_i915_private *dev_priv) out:mutex_unlock (&dev->mode_config.mutex); -intel_panel_init (&intel_connector->panel, fixed_mode, downclock_mode); +intel_panel_init (&intel_connector->panel, fixed_mode,NULL , + downclock_mode);intel_panel_setup_backlight (connector,INVALID_PIPE ); lvds_encoder->is_dual_link =compute_is_dual_link_lvds (lvds_encoder);drivers/gpu/drm/i915/intel_panel.c +2
-0@@ -1801,11 +1801,13 @@ intel_panel_init_backlight_funcs(struct intel_panel *panel)int intel_panel_init (struct intel_panel *panel,struct drm_display_mode *fixed_mode, +struct drm_display_mode *alt_fixed_mode,struct drm_display_mode *downclock_mode) {intel_panel_init_backlight_funcs (panel); panel->fixed_mode = fixed_mode; + panel->alt_fixed_mode = alt_fixed_mode; panel->downclock_mode = downclock_mode;return 0 ;
Signature · 5 lines
Jani Nikula, Intel Open Source Technology Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 1/4] drm/i915/edp: Allow alternate fixed mode for eDP if available.
Quoted 10 lines · Jani Nikula
Quoted 6 lines · Jim Bride
Some fixed resolution panels actually support more than one mode, with the only thing different being the refresh rate. Having this alternate mode available to us is desirable, because it allows us to test PSR on panels whose setup time at the preferred mode is too long. With this patch we allow the use of the alternate mode if it's available and it was specifically requested.
All in all this feels like a hack. The generic solution would be to allow any mode to be set again.
To an extent, I agree with you. I did things this way in an attempt to change the current behavior as little as possible. Personally, I'd rather see us allow any supported mode to be set.
Quoted 25 lines
A few specific comments inline.
BR,
Jani.Quoted 20 lines
Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Jim Bride <[email protected]>--- drivers/gpu/drm/i915/intel_dp.c | 34 +++++++++++++++++++++++++++++----- drivers/gpu/drm/i915/intel_drv.h | 2 ++ drivers/gpu/drm/i915/intel_dsi.c | 2 +- drivers/gpu/drm/i915/intel_dvo.c | 2 +- drivers/gpu/drm/i915/intel_lvds.c | 3 ++- drivers/gpu/drm/i915/intel_panel.c | 2 ++ 6 files changed, 37 insertions(+), 8 deletions(-)drivers/gpu/drm/i915/intel_dp.c +0
-0@@ -1637,6 +1637,19 @@ static int intel_dp_compute_bpp(struct intel_dp *intel_dp,return bpp; }
Quoted 14 lines
drivers/gpu/drm/i915/intel_dp.c static int intel_dp_compute_bpp(struct intel_dp *intel_dp, · line 1651
Quoted 12 lines
drivers/gpu/drm/i915/intel_dp.c +12
-0+static bool intel_edp_compare_alt_mode (struct drm_display_mode *m1, +struct drm_display_mode *m2) +{ +return (m1->hdisplay == m2->hdisplay && + m1->hsync_start == m2->hsync_start && + m1->hsync_end == m2->hsync_end && + m1->htotal == m2->htotal && + m1->vdisplay == m2->vdisplay && + m1->vsync_start == m2->vsync_start && + m1->vsync_end == m2->vsync_end && + m1->vtotal == m2->vtotal); +}See
drm_mode_equaland friends.
I did. The problem is that I needed a comparison without vscan being involved (see drm_mode_equal_no_clocks_no_stereo(), where the actual comparison happens.) This seemed like the least disruptive way to do that comparison.
Quoted 36 lines
Quoted 36 lines
drivers/gpu/drm/i915/intel_dp.c +12
-2+ bool intel_dp_compute_config(struct intel_encoder *encoder, struct intel_crtc_state *pipe_config,@@ -1674,8 +1687,16 @@ intel_dp_compute_config(struct intel_encoder *encoder, pipe_config->has_audio = intel_dp->has_audio && port !=PORT_A ;if (is_edp (intel_dp) && intel_connector->panel.fixed_mode) { -intel_fixed_panel_mode (intel_connector->panel.fixed_mode, - adjusted_mode); +struct drm_display_mode *panel_mode = + intel_connector->panel.alt_fixed_mode; +struct drm_display_mode *req_mode = &pipe_config->base.mode; + +if (!intel_edp_compare_alt_mode (req_mode, panel_mode)) + panel_mode = intel_connector->panel.fixed_mode; + +drm_mode_debug_printmodeline (panel_mode); + +intel_fixed_panel_mode (panel_mode, adjusted_mode);if (INTEL_GEN (dev_priv) >=9 ) {int ret;@@ -5829,6 +5850,7 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp,struct drm_device *dev = intel_encoder->base.dev;struct drm_i915_private *dev_priv =to_i915 (dev);struct drm_display_mode *fixed_mode =NULL ; +struct drm_display_mode *alt_fixed_mode =NULL ;struct drm_display_mode *downclock_mode =NULL ;bool has_dpcd;struct drm_display_mode *scan;@@ -5884,13 +5906,14 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp, } intel_connector->edid = edid;
Quoted 14 lines
drivers/gpu/drm/i915/intel_dp.c static bool intel_edp_init_connector(struct intel_dp *intel_dp, · line 5917
Quoted 11 lines
drivers/gpu/drm/i915/intel_dp.c +3
-2-/* prefer fixed mode from EDID if available */ +/* prefer fixed mode from EDID if available, save an alt mode also */ list_for_each_entry (scan, &connector->probed_modes, head) {if ((scan->type &DRM_MODE_TYPE_PREFERRED )) { fixed_mode =drm_mode_duplicate (dev, scan); downclock_mode =intel_dp_drrs_init ( intel_connector, fixed_mode); -break ; + }else { + alt_fixed_mode =drm_mode_duplicate (dev, scan); }This changes the fixed mode if there are more than one preferred mode. This will also leak all but the two modes.
I wasn't aware there can be more than one preferred mode. I thought the whole idea was to have a way of designating one mode of many that would provide (at least in the opinion of the panel's makers) the mode that will provide the best user experience. FWIW, on the panels I've tested with I haven't seen more than two modes supported natively in any case. If we follow your earlier suggestion about just letting mode sets happen on all supported modes then all of this stuff goes away.
Jim
Quoted 86 lines
Quoted 86 lines
drivers/gpu/drm/i915/intel_dp.c +2
-1}@@ -5927,7 +5950,8 @@ static bool intel_edp_init_connector(struct intel_dp *intel_dp, pipe_name(pipe)); } -intel_panel_init (&intel_connector->panel, fixed_mode, downclock_mode); +intel_panel_init (&intel_connector->panel, fixed_mode, alt_fixed_mode, + downclock_mode); intel_connector->panel.backlight.power = intel_edp_backlight_power;intel_panel_setup_backlight (connector, pipe);drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -265,6 +265,7 @@ struct intel_encoder {struct intel_panel {struct drm_display_mode *fixed_mode; +struct drm_display_mode *alt_fixed_mode;struct drm_display_mode *downclock_mode;int fitting_mode;@@ -1676,6 +1677,7 @@ void intel_overlay_reset(struct drm_i915_private *dev_priv);/* intel_panel.c */ int intel_panel_init (struct intel_panel *panel,struct drm_display_mode *fixed_mode, +struct drm_display_mode *alt_fixed_mode,struct drm_display_mode *downclock_mode);void intel_panel_fini (struct intel_panel *panel); void intel_fixed_panel_mode(const struct drm_display_mode *fixed_mode,drivers/gpu/drm/i915/intel_dsi.c +1
-1@@ -1852,7 +1852,7 @@ void intel_dsi_init(struct drm_i915_private *dev_priv) connector->display_info.width_mm = fixed_mode->width_mm; connector->display_info.height_mm = fixed_mode->height_mm; -intel_panel_init (&intel_connector->panel, fixed_mode,NULL ); +intel_panel_init (&intel_connector->panel, fixed_mode,NULL ,NULL );intel_panel_setup_backlight (connector,INVALID_PIPE );intel_dsi_add_properties (intel_connector);drivers/gpu/drm/i915/intel_dvo.c +1
-1@@ -554,7 +554,7 @@ void intel_dvo_init(struct drm_i915_private *dev_priv)*/ intel_panel_init (&intel_connector->panel,intel_dvo_get_current_mode (connector), -NULL ); +NULL ,NULL ); intel_dvo->panel_wants_dither = true; }drivers/gpu/drm/i915/intel_lvds.c +2
-1@@ -1181,7 +1181,8 @@ void intel_lvds_init(struct drm_i915_private *dev_priv) out:mutex_unlock (&dev->mode_config.mutex); -intel_panel_init (&intel_connector->panel, fixed_mode, downclock_mode); +intel_panel_init (&intel_connector->panel, fixed_mode,NULL , + downclock_mode);intel_panel_setup_backlight (connector,INVALID_PIPE ); lvds_encoder->is_dual_link =compute_is_dual_link_lvds (lvds_encoder);drivers/gpu/drm/i915/intel_panel.c +1
-0@@ -1801,11 +1801,13 @@ intel_panel_init_backlight_funcs(struct intel_panel *panel)int intel_panel_init (struct intel_panel *panel,struct drm_display_mode *fixed_mode, +struct drm_display_mode *alt_fixed_mode,struct drm_display_mode *downclock_mode) {intel_panel_init_backlight_funcs (panel);
Quoted 8 lines
Quoted 5 lines
drivers/gpu/drm/i915/intel_panel.c +1
-0panel->fixed_mode = fixed_mode; + panel->alt_fixed_mode = alt_fixed_mode; panel->downclock_mode = downclock_mode;return 0 ;Signature · 1 line
Jani Nikula, Intel Open Source Technology Center
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 2/4 drm/i915/psr: Clean-up intel_enable_source_psr1()
In reply to Jim BrideOn SKL+ there is a bit in SRD_CTL that software is not supposed to modify, but we currently clobber that bit when we enable PSR. In order to preserve the value of that bit, go ahead and read SRD_CTL and do a field-wise setting of the various bits that we need to initialize before writing the register back out. Additionally, go ahead and explicitly disable single-frame update since we aren't currently supporting it.
v2: Do a field-wise init on EDP_PSR_MAX_SLEEP_TIME even though we
always set it to the max value. (Rodrigo)
--- drivers/gpu/drm/i915/i915_reg.h | 4 ++++ drivers/gpu/drm/i915/intel_psr.c | 21 +++++++++++++++++++-- 2 files changed, 23 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/i915_reg.h +4 -0
@@ -3584,18 +3584,22 @@ enum {#define EDP_PSR_MIN_LINK_ENTRY_TIME_4_LINES (1<<25)#define EDP_PSR_MIN_LINK_ENTRY_TIME_2_LINES (2<<25)#define EDP_PSR_MIN_LINK_ENTRY_TIME_0_LINES (3<<25) +#define EDP_PSR_MAX_SLEEP_TIME_MASK (0x1f<<20)#define EDP_PSR_MAX_SLEEP_TIME_SHIFT 20#define EDP_PSR_SKIP_AUX_EXIT (1<<12)#define EDP_PSR_TP1_TP2_SEL (0<<11)#define EDP_PSR_TP1_TP3_SEL (1<<11) +#define EDP_PSR_TP2_TP3_TIME_MASK (3<<8)#define EDP_PSR_TP2_TP3_TIME_500us (0<<8)#define EDP_PSR_TP2_TP3_TIME_100us (1<<8)#define EDP_PSR_TP2_TP3_TIME_2500us (2<<8)#define EDP_PSR_TP2_TP3_TIME_0us (3<<8) +#define EDP_PSR_TP1_TIME_MASK (0x3<<4)#define EDP_PSR_TP1_TIME_500us (0<<4)#define EDP_PSR_TP1_TIME_100us (1<<4)#define EDP_PSR_TP1_TIME_2500us (2<<4)#define EDP_PSR_TP1_TIME_0us (3<<4) +#define EDP_PSR_IDLE_FRAME_MASK (0xf<<0)#define EDP_PSR_IDLE_FRAME_SHIFT 0#define EDP_PSR_AUX_CTL _MMIO(dev_priv->psr_mmio_base + 0x10)
drivers/gpu/drm/i915/intel_psr.c +19 -2
@@ -280,17 +280,32 @@ static void intel_enable_source_psr1(struct intel_dp *intel_dp)* with the 5 or 6 idle patterns. */ uint32_t idle_frames =max (6 , dev_priv->vbt.psr.idle_frames); -uint32_t val =EDP_PSR_ENABLE ; +uint32_t val =I915_READ (EDP_PSR_CTL ); + val |=EDP_PSR_ENABLE ; + + val &= ~EDP_PSR_MAX_SLEEP_TIME_MASK ; val |= max_sleep_time <<EDP_PSR_MAX_SLEEP_TIME_SHIFT ; + + val &= ~EDP_PSR_IDLE_FRAME_MASK ; val |= idle_frames <<EDP_PSR_IDLE_FRAME_SHIFT ; + val &= ~EDP_PSR_MIN_LINK_ENTRY_TIME_MASK ;if (IS_HASWELL (dev_priv)) val |=EDP_PSR_MIN_LINK_ENTRY_TIME_8_LINES ; -if (dev_priv->psr.link_standby) +if (dev_priv->psr.link_standby) { val |=EDP_PSR_LINK_STANDBY ; +/* SFU should only be enabled with link standby, but for +* now we do not support it. */ + val &= ~BDW_PSR_SINGLE_FRAME ; + }else { + val &= ~EDP_PSR_LINK_STANDBY ; + val &= ~BDW_PSR_SINGLE_FRAME ; + } + + val &= ~EDP_PSR_TP1_TIME_MASK ;if (dev_priv->vbt.psr.tp1_wakeup_time >5 ) val |= EDP_PSR_TP1_TIME_2500us;else if (dev_priv->vbt.psr.tp1_wakeup_time >1 )
@@ -300,6 +315,7 @@ static void intel_enable_source_psr1(struct intel_dp *intel_dp)else val |= EDP_PSR_TP1_TIME_0us; + val &= ~EDP_PSR_TP2_TP3_TIME_MASK ;if (dev_priv->vbt.psr.tp2_tp3_wakeup_time >5 ) val |= EDP_PSR_TP2_TP3_TIME_2500us;else if (dev_priv->vbt.psr.tp2_tp3_wakeup_time >1 )
@@ -309,6 +325,7 @@ static void intel_enable_source_psr1(struct intel_dp *intel_dp)else val |= EDP_PSR_TP2_TP3_TIME_0us; + val &= ~EDP_PSR_TP1_TP3_SEL ;if (intel_dp_source_supports_hbr2 (intel_dp) &&drm_dp_tps3_supported (intel_dp->dpcd)) val |=EDP_PSR_TP1_TP3_SEL ;
Signature · 6 lines
2.7.4 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 2/4] drm/i915/psr: Clean-up intel_enable_source_psr1()
Quoted 66 lines · Jim Bride
On SKL+ there is a bit in
SRD_CTLthat software is not supposed to modify, but we currently clobber that bit when we enable PSR. In order to preserve the value of that bit, go ahead and readSRD_CTLand do a field-wise setting of the various bits that we need to initialize before writing the register back out. Additionally, go ahead and explicitly disable single-frame update since we aren't currently supporting it.v2: Do a field-wise init on
EDP_PSR_MAX_SLEEP_TIMEeven though we
always set it to the max value. (Rodrigo)Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Wayne Boyer <[email protected]>Signed-off-by Jim Bride <[email protected]>--- drivers/gpu/drm/i915/i915_reg.h | 4 ++++ drivers/gpu/drm/i915/intel_psr.c | 21 +++++++++++++++++++-- 2 files changed, 23 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/i915_reg.h +4
-0@@ -3584,18 +3584,22 @@ enum {#define EDP_PSR_MIN_LINK_ENTRY_TIME_4_LINES (1<<25)#define EDP_PSR_MIN_LINK_ENTRY_TIME_2_LINES (2<<25)#define EDP_PSR_MIN_LINK_ENTRY_TIME_0_LINES (3<<25) +#define EDP_PSR_MAX_SLEEP_TIME_MASK (0x1f<<20)#define EDP_PSR_MAX_SLEEP_TIME_SHIFT 20#define EDP_PSR_SKIP_AUX_EXIT (1<<12)#define EDP_PSR_TP1_TP2_SEL (0<<11)#define EDP_PSR_TP1_TP3_SEL (1<<11) +#define EDP_PSR_TP2_TP3_TIME_MASK (3<<8)#define EDP_PSR_TP2_TP3_TIME_500us (0<<8)#define EDP_PSR_TP2_TP3_TIME_100us (1<<8)#define EDP_PSR_TP2_TP3_TIME_2500us (2<<8)#define EDP_PSR_TP2_TP3_TIME_0us (3<<8) +#define EDP_PSR_TP1_TIME_MASK (0x3<<4)#define EDP_PSR_TP1_TIME_500us (0<<4)#define EDP_PSR_TP1_TIME_100us (1<<4)#define EDP_PSR_TP1_TIME_2500us (2<<4)#define EDP_PSR_TP1_TIME_0us (3<<4) +#define EDP_PSR_IDLE_FRAME_MASK (0xf<<0)#define EDP_PSR_IDLE_FRAME_SHIFT 0#define EDP_PSR_AUX_CTL _MMIO(dev_priv->psr_mmio_base + 0x10)drivers/gpu/drm/i915/intel_psr.c +6
-1@@ -280,17 +280,32 @@ static void intel_enable_source_psr1(struct intel_dp *intel_dp)* with the 5 or 6 idle patterns. */ uint32_t idle_frames =max (6 , dev_priv->vbt.psr.idle_frames); -uint32_t val =EDP_PSR_ENABLE ; +uint32_t val =I915_READ (EDP_PSR_CTL ); + val |=EDP_PSR_ENABLE ; + + val &= ~EDP_PSR_MAX_SLEEP_TIME_MASK ; val |= max_sleep_time <<EDP_PSR_MAX_SLEEP_TIME_SHIFT ; + + val &= ~EDP_PSR_IDLE_FRAME_MASK ; val |= idle_frames <<EDP_PSR_IDLE_FRAME_SHIFT ;
drivers/gpu/drm/i915/intel_psr.c static void intel_enable_source_psr1(struct intel_dp *intel_dp) · line 301
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +4
-1+ val &= ~EDP_PSR_MIN_LINK_ENTRY_TIME_MASK ;if (IS_HASWELL (dev_priv)) val |=EDP_PSR_MIN_LINK_ENTRY_TIME_8_LINES ; -if (dev_priv->psr.link_standby) +if (dev_priv->psr.link_standby) { val |=EDP_PSR_LINK_STANDBY ; +/* SFU should only be enabled with link standby, but for +* now we do not support it. */
/* goes to next line
drivers/gpu/drm/i915/intel_psr.c static void intel_enable_source_psr1(struct intel_dp *intel_dp) · line 305
Quoted 4 lines
drivers/gpu/drm/i915/intel_psr.c +4
-0+ val &= ~BDW_PSR_SINGLE_FRAME ; + }else { + val &= ~EDP_PSR_LINK_STANDBY ; + val &= ~BDW_PSR_SINGLE_FRAME ;
probably better to do this out of the if to avoid duplication. Comment above already explain it well.
with these feel free to use:
Quoted 29 lines
drivers/gpu/drm/i915/intel_psr.c +5
-1+ } + + val &= ~EDP_PSR_TP1_TIME_MASK ;if (dev_priv->vbt.psr.tp1_wakeup_time >5 ) val |= EDP_PSR_TP1_TIME_2500us;else if (dev_priv->vbt.psr.tp1_wakeup_time >1 )@@ -300,6 +315,7 @@ static void intel_enable_source_psr1(struct intel_dp *intel_dp)else val |= EDP_PSR_TP1_TIME_0us; + val &= ~EDP_PSR_TP2_TP3_TIME_MASK ;if (dev_priv->vbt.psr.tp2_tp3_wakeup_time >5 ) val |= EDP_PSR_TP2_TP3_TIME_2500us;else if (dev_priv->vbt.psr.tp2_tp3_wakeup_time >1 )@@ -309,6 +325,7 @@ static void intel_enable_source_psr1(struct intel_dp *intel_dp)else val |= EDP_PSR_TP2_TP3_TIME_0us; + val &= ~EDP_PSR_TP1_TP3_SEL ;if (intel_dp_source_supports_hbr2 (intel_dp) &&drm_dp_tps3_supported (intel_dp->dpcd)) val |=EDP_PSR_TP1_TP3_SEL ; --2.7.4
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 6 lines
Rodrigo Vivi Blog: http://blog.vivi.eng.br _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 3/4 drm/i915/edp: Be less aggressive about changing link config on eDP
In reply to Jim BrideThis set of changes has some history to them. There were several attempts to add what was called "fast link training" to i915, which actually wasn't fast link training as per the DP spec. These changes were
5fa836a9d859 ("drm/i915: DP link training optimization") 4e96c97742f4 ("drm/i915: eDP link training optimization")
which were eventually hand-reverted by
34511dce4 ("drm/i915: Revert DisplayPort fast link training feature")
in kernel 4.7-rc4. The eDP pieces of the above revert, however, had some very bad side-effects on PSR functionality on Skylake. The issue at hand is that when PSR exits i915 briefly emits TP1 followed by TP2/3 (depending on the original link configuration) in order to quickly get the source and sink back in synchronization across the link before handing control back to the i915. There's an assumption that none of the link configuration information has changed (and thus it's still valid) since the last full link training operation. The revert above was identified via a bisect as the cause of some of Skylake's PSR woes. This patch, largely based on
commit 4e96c97742f4201edf1b0f8e1b1b6b2ac6ff33e7
Author: Mika Kahola <[email protected]>
Date: Wed Apr 29 09:17:39 2015 +0300
drm/i915: eDP link training optimization
puts the eDP portions of this patch back in place. None of the flickering issues that spurred the revert have been seen, and I suspect the real culprits here were addressed by some of the recent link training changes that Manasi has implemented, and PSR on Skylake is definitely more happy with these changes in-place.
--- drivers/gpu/drm/i915/intel_dp.c | 4 +++- drivers/gpu/drm/i915/intel_dp_link_training.c | 11 ++++++++++- drivers/gpu/drm/i915/intel_drv.h | 2 ++ 3 files changed, 15 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_dp.c +3 -1
@@ -106,7 +106,7 @@ static const int default_rates[] = { 162000, 270000, 540000 };* If a CPU or PCH DP output is attached to an eDP panel, this function * will return true, and false otherwise. */ -static bool is_edp (struct intel_dp *intel_dp) +bool is_edp (struct intel_dp *intel_dp) {struct intel_digital_port *intel_dig_port =dp_to_dig_port (intel_dp);
@@ -4690,6 +4690,7 @@ intel_dp_long_pulse(struct intel_connector *intel_connector) intel_dp->max_link_rate =intel_dp_max_common_rate (intel_dp); intel_dp->reset_link_params = false; + intel_dp->train_set_valid = false; }intel_dp_print_rates (intel_dp);
@@ -6052,6 +6053,7 @@ intel_dp_init_connector(struct intel_digital_port *intel_dig_port,intel_dp_set_source_rates (intel_dp); intel_dp->reset_link_params = true; + intel_dp->train_set_valid = false; intel_dp->pps_pipe =INVALID_PIPE ; intel_dp->active_pipe =INVALID_PIPE ;
drivers/gpu/drm/i915/intel_dp_link_training.c +10 -1
@@ -94,7 +94,8 @@ static bool intel_dp_reset_link_train(struct intel_dp *intel_dp, uint8_t dp_train_pat) { - memset(intel_dp->train_set, 0, sizeof(intel_dp->train_set)); +if (!intel_dp->train_set_valid) +memset (intel_dp->train_set,0 ,sizeof (intel_dp->train_set));intel_dp_set_signal_levels (intel_dp);return intel_dp_set_link_train (intel_dp, dp_train_pat); }
@@ -162,6 +163,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp) DP_TRAINING_PATTERN_1 | DP_LINK_SCRAMBLING_DISABLE)) {DRM_ERROR ("failed to enable link training\n" ); + intel_dp->train_set_valid = false;return false; }
@@ -174,21 +176,25 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp)if (!intel_dp_get_link_status (intel_dp, link_status)) {DRM_ERROR ("failed to get link status\n" ); + intel_dp->train_set_valid = false;return false; }if (drm_dp_clock_recovery_ok (link_status, intel_dp->lane_count)) {DRM_DEBUG_KMS ("clock recovery OK\n" ); + intel_dp->train_set_valid =is_edp (intel_dp);return true; }if (voltage_tries ==5 ) {DRM_DEBUG_KMS ("Same voltage tried 5 times\n" ); + intel_dp->train_set_valid = false;return false; }if (max_vswing_tries ==1 ) {DRM_DEBUG_KMS ("Max Voltage Swing reached\n" ); + intel_dp->train_set_valid = false;return false; }
@@ -198,6 +204,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp)intel_get_adjust_train (intel_dp, link_status);if (!intel_dp_update_link_train (intel_dp)) {DRM_ERROR ("failed to update link training\n" ); + intel_dp->train_set_valid = false;return false; }
@@ -256,6 +263,7 @@ intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp) training_pattern | DP_LINK_SCRAMBLING_DISABLE)) {DRM_ERROR ("failed to start channel equalization\n" ); + intel_dp->train_set_valid = false;return false; }
@@ -296,6 +304,7 @@ intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp)/* Try 5 times, else fail and try at lower BW */ if (tries ==5 ) {intel_dp_dump_link_status (link_status); + intel_dp->train_set_valid = false;DRM_DEBUG_KMS ("Channel equalization failed 5 times\n" ); }
drivers/gpu/drm/i915/intel_drv.h +2 -0
@@ -977,6 +977,7 @@ struct intel_dp {struct drm_dp_aux aux;enum intel_display_power_domain aux_power_domain;uint8_t train_set[4 ]; +bool train_set_valid;int panel_power_up_delay;int panel_power_down_delay;int panel_power_cycle_delay;
@@ -1551,6 +1552,7 @@ bool intel_dp_read_dpcd(struct intel_dp *intel_dp);bool __intel_dp_read_desc (struct intel_dp *intel_dp,struct intel_dp_desc *desc);bool intel_dp_read_desc (struct intel_dp *intel_dp); +bool is_edp (struct intel_dp *intel_dp);int intel_dp_link_required (int pixel_clock,int bpp);int intel_dp_max_data_rate (int max_link_clock,int max_lanes); bool intel_digital_port_connected(struct drm_i915_private *dev_priv,
Signature · 6 lines
2.7.4 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jani Nikula
maintainerRe: [PATCH 3/4] drm/i915/edp: Be less aggressive about changing link config on eDP
Quoted 27 lines · Jim Bride
This set of changes has some history to them. There were several attempts to add what was called "fast link training" to i915, which actually wasn't fast link training as per the DP spec. These changes were
5fa836a9d859("drm/i915: DP link training optimization")4e96c97742f4("drm/i915: eDP link training optimization")which were eventually hand-reverted by
34511dce4("drm/i915: Revert DisplayPort fast link training feature")in kernel 4.7-rc4. The eDP pieces of the above revert, however, had some very bad side-effects on PSR functionality on Skylake. The issue at hand is that when PSR exits i915 briefly emits TP1 followed by TP2/3 (depending on the original link configuration) in order to quickly get the source and sink back in synchronization across the link before handing control back to the i915. There's an assumption that none of the link configuration information has changed (and thus it's still valid) since the last full link training operation. The revert above was identified via a bisect as the cause of some of Skylake's PSR woes. This patch, largely based on
commit
4e96c97742f4201edf1b0f8e1b1b6b2ac6ff33e7
Author: Mika Kahola <[email protected]>
Date: Wed Apr 29 09:17:39 2015 +0300
drm/i915: eDP link training optimization
Quoted 5 lines
puts the eDP portions of this patch back in place. None of the flickering issues that spurred the revert have been seen, and I suspect the real culprits here were addressed by some of the recent link training changes that Manasi has implemented, and PSR on Skylake is definitely more happy with these changes in-place.
I'm weary of all the back and forth wrt PSR and DP, and wary of creating new ones. Would it make sense to restrict this patch to PSR?
BR,
Jani.
Quoted 134 lines
Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Manasi D Navare <[email protected]>Cc Mika Kahola <[email protected]>Fixes 34511dce4 ("drm/i915: Revert DisplayPort fast link training feature")Signed-off-by Jim Bride <[email protected]>--- drivers/gpu/drm/i915/intel_dp.c | 4 +++- drivers/gpu/drm/i915/intel_dp_link_training.c | 11 ++++++++++- drivers/gpu/drm/i915/intel_drv.h | 2 ++ 3 files changed, 15 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_dp.c +3
-1@@ -106,7 +106,7 @@ static const int default_rates[] = { 162000, 270000, 540000 };* If a CPU or PCH DP output is attached to an eDP panel, this function * will return true, and false otherwise. */ -static bool is_edp (struct intel_dp *intel_dp) +bool is_edp (struct intel_dp *intel_dp) {struct intel_digital_port *intel_dig_port =dp_to_dig_port (intel_dp);@@ -4690,6 +4690,7 @@ intel_dp_long_pulse(struct intel_connector *intel_connector) intel_dp->max_link_rate =intel_dp_max_common_rate (intel_dp); intel_dp->reset_link_params = false; + intel_dp->train_set_valid = false; }intel_dp_print_rates (intel_dp);@@ -6052,6 +6053,7 @@ intel_dp_init_connector(struct intel_digital_port *intel_dig_port,intel_dp_set_source_rates (intel_dp); intel_dp->reset_link_params = true; + intel_dp->train_set_valid = false; intel_dp->pps_pipe =INVALID_PIPE ; intel_dp->active_pipe =INVALID_PIPE ;drivers/gpu/drm/i915/intel_dp_link_training.c +10
-1@@ -94,7 +94,8 @@ static bool intel_dp_reset_link_train(struct intel_dp *intel_dp, uint8_t dp_train_pat) { - memset(intel_dp->train_set, 0, sizeof(intel_dp->train_set)); +if (!intel_dp->train_set_valid) +memset (intel_dp->train_set,0 ,sizeof (intel_dp->train_set));intel_dp_set_signal_levels (intel_dp);return intel_dp_set_link_train (intel_dp, dp_train_pat); }@@ -162,6 +163,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp) DP_TRAINING_PATTERN_1 | DP_LINK_SCRAMBLING_DISABLE)) {DRM_ERROR ("failed to enable link training\n" ); + intel_dp->train_set_valid = false;return false; }@@ -174,21 +176,25 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp)if (!intel_dp_get_link_status (intel_dp, link_status)) {DRM_ERROR ("failed to get link status\n" ); + intel_dp->train_set_valid = false;return false; }if (drm_dp_clock_recovery_ok (link_status, intel_dp->lane_count)) {DRM_DEBUG_KMS ("clock recovery OK\n" ); + intel_dp->train_set_valid =is_edp (intel_dp);return true; }if (voltage_tries ==5 ) {DRM_DEBUG_KMS ("Same voltage tried 5 times\n" ); + intel_dp->train_set_valid = false;return false; }if (max_vswing_tries ==1 ) {DRM_DEBUG_KMS ("Max Voltage Swing reached\n" ); + intel_dp->train_set_valid = false;return false; }@@ -198,6 +204,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp)intel_get_adjust_train (intel_dp, link_status);if (!intel_dp_update_link_train (intel_dp)) {DRM_ERROR ("failed to update link training\n" ); + intel_dp->train_set_valid = false;return false; }@@ -256,6 +263,7 @@ intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp) training_pattern | DP_LINK_SCRAMBLING_DISABLE)) {DRM_ERROR ("failed to start channel equalization\n" ); + intel_dp->train_set_valid = false;return false; }@@ -296,6 +304,7 @@ intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp)/* Try 5 times, else fail and try at lower BW */ if (tries ==5 ) {intel_dp_dump_link_status (link_status); + intel_dp->train_set_valid = false;DRM_DEBUG_KMS ("Channel equalization failed 5 times\n" ); }drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -977,6 +977,7 @@ struct intel_dp {struct drm_dp_aux aux;enum intel_display_power_domain aux_power_domain;uint8_t train_set[4 ]; +bool train_set_valid;int panel_power_up_delay;int panel_power_down_delay;int panel_power_cycle_delay;@@ -1551,6 +1552,7 @@ bool intel_dp_read_dpcd(struct intel_dp *intel_dp);bool __intel_dp_read_desc (struct intel_dp *intel_dp,struct intel_dp_desc *desc);bool intel_dp_read_desc (struct intel_dp *intel_dp); +bool is_edp (struct intel_dp *intel_dp);int intel_dp_link_required (int pixel_clock,int bpp);int intel_dp_max_data_rate (int max_link_clock,int max_lanes); bool intel_digital_port_connected(struct drm_i915_private *dev_priv,
Signature · 5 lines
Jani Nikula, Intel Open Source Technology Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 3/4] drm/i915/edp: Be less aggressive about changing link config on eDP
Quoted 28 lines · Jani Nikula
Quoted 27 lines · Jim Bride
This set of changes has some history to them. There were several attempts to add what was called "fast link training" to i915, which actually wasn't fast link training as per the DP spec. These changes were
5fa836a9d859("drm/i915: DP link training optimization")4e96c97742f4("drm/i915: eDP link training optimization")which were eventually hand-reverted by
34511dce4("drm/i915: Revert DisplayPort fast link training feature")in kernel 4.7-rc4. The eDP pieces of the above revert, however, had some very bad side-effects on PSR functionality on Skylake. The issue at hand is that when PSR exits i915 briefly emits TP1 followed by TP2/3 (depending on the original link configuration) in order to quickly get the source and sink back in synchronization across the link before handing control back to the i915. There's an assumption that none of the link configuration information has changed (and thus it's still valid) since the last full link training operation. The revert above was identified via a bisect as the cause of some of Skylake's PSR woes. This patch, largely based on
commit
4e96c97742f4201edf1b0f8e1b1b6b2ac6ff33e7
Author: Mika Kahola <[email protected]>
Date: Wed Apr 29 09:17:39 2015 +0300
drm/i915: eDP link training optimization
Quoted 8 lines
Quoted 5 lines
puts the eDP portions of this patch back in place. None of the flickering issues that spurred the revert have been seen, and I suspect the real culprits here were addressed by some of the recent link training changes that Manasi has implemented, and PSR on Skylake is definitely more happy with these changes in-place.
I'm weary of all the back and forth wrt PSR and DP, and wary of creating new ones. Would it make sense to restrict this patch to PSR?
Honestly, although it could be limited to PSR, I think it's beneficial to leave it in place as it is. For eDP, where panels generally only support a small number of native modes, I think we end up doing a lot of extra work by re-calculating all of the link information every time. Mika seems think it's pretty safe as well.
Jim
Quoted 131 lines
BR,
Jani.Quoted 126 lines
Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Manasi D Navare <[email protected]>Cc Mika Kahola <[email protected]>Fixes 34511dce4 ("drm/i915: Revert DisplayPort fast link training feature")Signed-off-by Jim Bride <[email protected]>--- drivers/gpu/drm/i915/intel_dp.c | 4 +++- drivers/gpu/drm/i915/intel_dp_link_training.c | 11 ++++++++++- drivers/gpu/drm/i915/intel_drv.h | 2 ++ 3 files changed, 15 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_dp.c +3
-1@@ -106,7 +106,7 @@ static const int default_rates[] = { 162000, 270000, 540000 };* If a CPU or PCH DP output is attached to an eDP panel, this function * will return true, and false otherwise. */ -static bool is_edp (struct intel_dp *intel_dp) +bool is_edp (struct intel_dp *intel_dp) {struct intel_digital_port *intel_dig_port =dp_to_dig_port (intel_dp);@@ -4690,6 +4690,7 @@ intel_dp_long_pulse(struct intel_connector *intel_connector) intel_dp->max_link_rate =intel_dp_max_common_rate (intel_dp); intel_dp->reset_link_params = false; + intel_dp->train_set_valid = false; }intel_dp_print_rates (intel_dp);@@ -6052,6 +6053,7 @@ intel_dp_init_connector(struct intel_digital_port *intel_dig_port,intel_dp_set_source_rates (intel_dp); intel_dp->reset_link_params = true; + intel_dp->train_set_valid = false; intel_dp->pps_pipe =INVALID_PIPE ; intel_dp->active_pipe =INVALID_PIPE ;drivers/gpu/drm/i915/intel_dp_link_training.c +10
-1@@ -94,7 +94,8 @@ static bool intel_dp_reset_link_train(struct intel_dp *intel_dp, uint8_t dp_train_pat) { - memset(intel_dp->train_set, 0, sizeof(intel_dp->train_set)); +if (!intel_dp->train_set_valid) +memset (intel_dp->train_set,0 ,sizeof (intel_dp->train_set));intel_dp_set_signal_levels (intel_dp);return intel_dp_set_link_train (intel_dp, dp_train_pat); }@@ -162,6 +163,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp) DP_TRAINING_PATTERN_1 | DP_LINK_SCRAMBLING_DISABLE)) {DRM_ERROR ("failed to enable link training\n" ); + intel_dp->train_set_valid = false;return false; }@@ -174,21 +176,25 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp)if (!intel_dp_get_link_status (intel_dp, link_status)) {DRM_ERROR ("failed to get link status\n" ); + intel_dp->train_set_valid = false;return false; }if (drm_dp_clock_recovery_ok (link_status, intel_dp->lane_count)) {DRM_DEBUG_KMS ("clock recovery OK\n" ); + intel_dp->train_set_valid =is_edp (intel_dp);return true; }if (voltage_tries ==5 ) {DRM_DEBUG_KMS ("Same voltage tried 5 times\n" ); + intel_dp->train_set_valid = false;return false; }if (max_vswing_tries ==1 ) {DRM_DEBUG_KMS ("Max Voltage Swing reached\n" ); + intel_dp->train_set_valid = false;return false; }@@ -198,6 +204,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp)intel_get_adjust_train (intel_dp, link_status);if (!intel_dp_update_link_train (intel_dp)) {DRM_ERROR ("failed to update link training\n" ); + intel_dp->train_set_valid = false;return false; }@@ -256,6 +263,7 @@ intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp) training_pattern | DP_LINK_SCRAMBLING_DISABLE)) {DRM_ERROR ("failed to start channel equalization\n" ); + intel_dp->train_set_valid = false;return false; }@@ -296,6 +304,7 @@ intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp)/* Try 5 times, else fail and try at lower BW */ if (tries ==5 ) {intel_dp_dump_link_status (link_status); + intel_dp->train_set_valid = false;DRM_DEBUG_KMS ("Channel equalization failed 5 times\n" ); }drivers/gpu/drm/i915/intel_drv.h +1
-0@@ -977,6 +977,7 @@ struct intel_dp {struct drm_dp_aux aux;enum intel_display_power_domain aux_power_domain;uint8_t train_set[4 ]; +bool train_set_valid;int panel_power_up_delay;int panel_power_down_delay;int panel_power_cycle_delay;
Quoted 11 lines
Quoted 8 lines
drivers/gpu/drm/i915/intel_drv.h +1
-0@@ -1551,6 +1552,7 @@ bool intel_dp_read_dpcd(struct intel_dp *intel_dp);bool __intel_dp_read_desc (struct intel_dp *intel_dp,struct intel_dp_desc *desc);bool intel_dp_read_desc (struct intel_dp *intel_dp); +bool is_edp (struct intel_dp *intel_dp);int intel_dp_link_required (int pixel_clock,int bpp);int intel_dp_max_data_rate (int max_link_clock,int max_lanes); bool intel_digital_port_connected(struct drm_i915_private *dev_priv,Signature · 1 line
Jani Nikula, Intel Open Source Technology Center
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 3/4] drm/i915/edp: Be less aggressive about changing link config on eDP
In reply to Jim BrideQuoted 36 lines · Jim Bride
This set of changes has some history to them. There were several attempts
to add what was called "fast link training" to i915, which actually wasn't
fast link training as per the DP spec. These changes were
5fa836a9d859("drm/i915: DP link training optimization")4e96c97742f4("drm/i915: eDP link training optimization")which were eventually hand-reverted by
34511dce4("drm/i915: Revert DisplayPort fast link training feature")in kernel 4.7-rc4. The eDP pieces of the above revert, however, had some
very bad side-effects on PSR functionality on Skylake. The issue at hand is that when PSR exits i915 briefly emits TP1 followed by TP2/3 (depending on the original link configuration) in order to quickly get
the source and sink back in synchronization across the link before handing
control back to the i915. There's an assumption that none of the link
configuration information has changed (and thus it's still valid) since the
last full link training operation. The revert above was identified via a
bisect as the cause of some of Skylake's PSR woes. This patch, largely
based oncommit
4e96c97742f4201edf1b0f8e1b1b6b2ac6ff33e7
Author: Mika Kahola <[email protected]>
Date: Wed Apr 29 09:17:39 2015 +0300
drm/i915: eDP link training optimization
Quoted 8 lines
puts the eDP portions of this patch back in place. None of the flickering
issues that spurred the revert have been seen, and I suspect the real culprits here were addressed by some of the recent link training changes
that Manasi has implemented, and PSR on Skylake is definitely more happy
with these changes in-place.
We reverted this back in the day due to bug reports we received from the community concerning flickering. However, you have to remember that during that time also the watermark work was ongoing. We couldn't pinpoint one issue or root cause that triggered these reported flickering cases. Therefore we decided to revert these optimizations. Personally, I feel that this would have been safe for eDP case.
Quoted 161 lines
Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Cc Manasi D Navare <[email protected]>Cc Mika Kahola <[email protected]>Fixes 34511dce4 ("drm/i915: Revert DisplayPort fast link trainingfeature")
Signed-off-by Jim Bride <[email protected]>---
drivers/gpu/drm/i915/intel_dp.c | 4 +++-drivers/gpu/drm/i915/intel_dp_link_training.c| 11 ++++++++++- drivers/gpu/drm/i915/intel_drv.h | 2 ++3 files changed, 15 insertions(+), 2 deletions(-)drivers/gpu/drm/i915/intel_dp.c +0
-0@@ -106,7 +106,7 @@ static const int default_rates[] = { 162000, 270000, 540000 }; * If a CPU or PCH DP output is attached to an eDP panel, thisfunction
* will return true, and false otherwise.
*/drivers/gpu/drm/i915/intel_dp.c +1
-1-static bool is_edp (struct intel_dp *intel_dp) +bool is_edp (struct intel_dp *intel_dp){
structintel_digital_port*intel_dig_port=dp_to_dig_port(intel_dp);drivers/gpu/drm/i915/intel_dp.c +0
-0@@ -4690,6 +4690,7 @@ intel_dp_long_pulse(struct intel_connector *intel_connector)
intel_dp->max_link_rate=intel_dp_max_common_rate(intel_dp);
intel_dp->reset_link_params= false;drivers/gpu/drm/i915/intel_dp.c +1
-0+ intel_dp->train_set_valid = false;}
intel_dp_print_rates(intel_dp);drivers/gpu/drm/i915/intel_dp.c +0
-0@@ -6052,6 +6053,7 @@ intel_dp_init_connector(structintel_digital_port *intel_dig_port, intel_dp_set_source_rates(intel_dp);
intel_dp->reset_link_params= true;drivers/gpu/drm/i915/intel_dp.c +1
-0+ intel_dp->train_set_valid = false;
intel_dp->pps_pipe=INVALID_PIPE;
intel_dp->active_pipe=INVALID_PIPE;drivers/gpu/drm/i915/intel_dp_link_training.c +2
-1@@ -94,7 +94,8 @@ static bool intel_dp_reset_link_train(struct intel_dp *intel_dp, uint8_t dp_train_pat) { -memset (intel_dp->train_set,0 ,sizeof (intel_dp->train_set)); +if (!intel_dp->train_set_valid) +memset (intel_dp->train_set,0 ,sizeof (intel_dp- >train_set)); intel_dp_set_signal_levels(intel_dp); return intel_dp_set_link_train(intel_dp, dp_train_pat);}
drivers/gpu/drm/i915/intel_dp_link_training.c +0
-0@@ -162,6 +163,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp)DP_TRAINING_PATTERN_1 |
DP_LINK_SCRAMBLING_DISABLE)) {
DRM_ERROR("failed to enable link training\n");drivers/gpu/drm/i915/intel_dp_link_training.c +1
-0+ intel_dp->train_set_valid = false;return false;
}drivers/gpu/drm/i915/intel_dp_link_training.c +0
-0@@ -174,21 +176,25 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp)
if (!intel_dp_get_link_status(intel_dp,link_status)) {
DRM_ERROR("failed to get link status\n");drivers/gpu/drm/i915/intel_dp_link_training.c +1
-0+ intel_dp->train_set_valid = false;return false;
}
if (drm_dp_clock_recovery_ok(link_status, intel_dp-Quoted 1 line
lane_count)) {
DRM_DEBUG_KMS("clock recovery OK\n");drivers/gpu/drm/i915/intel_dp_link_training.c +1
-0+ intel_dp->train_set_valid =
is_edp(intel_dp);
return true;
}
if (voltage_tries== 5) {DRM_DEBUG_KMS("Same voltage tried 5 times\n");drivers/gpu/drm/i915/intel_dp_link_training.c +1
-0+ intel_dp->train_set_valid = false;return false;
}
if (max_vswing_tries== 1) {DRM_DEBUG_KMS("Max Voltage Swing reached\n");drivers/gpu/drm/i915/intel_dp_link_training.c +1
-0+ intel_dp->train_set_valid = false;return false;
}drivers/gpu/drm/i915/intel_dp_link_training.c +0
-0@@ -198,6 +204,7 @@ intel_dp_link_training_clock_recovery(struct intel_dp *intel_dp) intel_get_adjust_train(intel_dp, link_status); if (!intel_dp_update_link_train(intel_dp)) {
DRM_ERROR("failed to update link training\n");drivers/gpu/drm/i915/intel_dp_link_training.c +1
-0+ intel_dp->train_set_valid = false;return false;
}drivers/gpu/drm/i915/intel_dp_link_training.c +0
-0@@ -256,6 +263,7 @@
intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp)
training_pattern |DP_LINK_SCRAMBLING_DISABLE)) {DRM_ERROR("failed to start channel equalization\n");drivers/gpu/drm/i915/intel_dp_link_training.c +1
-0+ intel_dp->train_set_valid = false;return false;
}drivers/gpu/drm/i915/intel_dp_link_training.c +0
-0@@ -296,6 +304,7 @@
intel_dp_link_training_channel_equalization(struct intel_dp *intel_dp)
/* Try 5 times, else fail and try at lower BW */ if (tries == 5) {intel_dp_dump_link_status(link_status);drivers/gpu/drm/i915/intel_dp_link_training.c +1
-0+ intel_dp->train_set_valid = false;
DRM_DEBUG_KMS("Channel equalization failed 5 times\n");
}drivers/gpu/drm/i915/intel_drv.h +2
-0@@ -977,6 +977,7 @@ struct intel_dp { struct drm_dp_aux aux; enum intel_display_power_domain aux_power_domain; uint8_t train_set[4]; +bool train_set_valid; int panel_power_up_delay; int panel_power_down_delay; int panel_power_cycle_delay;@@ -1551,6 +1552,7 @@ bool intel_dp_read_dpcd(struct intel_dp *intel_dp); bool __intel_dp_read_desc(struct intel_dp *intel_dp, struct intel_dp_desc *desc); bool intel_dp_read_desc(struct intel_dp *intel_dp); +bool is_edp (struct intel_dp *intel_dp); int intel_dp_link_required(int pixel_clock, int bpp); int intel_dp_max_data_rate(int max_link_clock, int max_lanes);bool intel_digital_port_connected(struct
drm_i915_private*dev_priv,
Signature · 6 lines
Mika Kahola - Intel OTC _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH 4/4 drm/i915/psr: Account for sink CRC raciness on some panels
In reply to Jim BrideAccording to the eDP spec, when the count field in TEST_SINK_MISC increments then the six bytes of sink CRC information in the DPCD should be valid. Unfortunately, this doesn't seem to be the case on some panels, and as a result we get some incorrect and inconsistent values from the sink CRC DPCD locations at times. This problem exhibits itself more on faster processors (relative failure rates HSW < SKL < KBL.) In order to try and account for this, we try a lot harder to read the sink CRC until we get consistent values twice in a row before returning what we read and delay for a time before trying to read. We still see some occasional failures, but reading the sink CRC is much more reliable, particularly on SKL and KBL, with these changes than without.
--- drivers/gpu/drm/i915/i915_debugfs.c | 14 +++++++-- drivers/gpu/drm/i915/intel_dp.c | 57 ++++++++++++++++++++++++++++++++----- 2 files changed, 61 insertions(+), 10 deletions(-)
drivers/gpu/drm/i915/i915_debugfs.c +11 -3
@@ -2718,7 +2718,7 @@ static int i915_sink_crc(struct seq_file *m, void *data)struct intel_connector *connector;struct drm_connector_list_iter conn_iter;struct intel_dp *intel_dp =NULL ; -int ret; +int ret, tries =6 ;u8 crc[6 ];drm_modeset_lock_all (dev);
@@ -2738,9 +2738,17 @@ static int i915_sink_crc(struct seq_file *m, void *data) intel_dp =enc_to_intel_dp (connector->base.state->best_encoder); - ret =intel_dp_sink_crc (intel_dp, crc); -if (ret) +memset (crc,0 ,6 ); +do { + ret =intel_dp_sink_crc (intel_dp, crc); +if (ret == -ETIMEDOUT ) +usleep_range (500 ,700 ); + }while ((ret == -ETIMEDOUT ) && --tries); + +if (ret !=0 ) { +seq_printf (m,"000000000000\n" ); goto out; + } seq_printf(m, "%02x%02x%02x%02x%02x%02x\n", crc[0], crc[1], crc[2],
drivers/gpu/drm/i915/intel_dp.c +50 -7
101 lines not on this page · raw message
Signature · 6 lines
2.7.4 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jani Nikula
maintainerRe: [PATCH 4/4] drm/i915/psr: Account for sink CRC raciness on some panels
Quoted 11 lines · Jim Bride
According to the eDP spec, when the count field in
TEST_SINK_MISCincrements then the six bytes of sink CRC information in the DPCD should be valid. Unfortunately, this doesn't seem to be the case on some panels, and as a result we get some incorrect and inconsistent values from the sink CRC DPCD locations at times. This problem exhibits itself more on faster processors (relative failure rates HSW < SKL < KBL.) In order to try and account for this, we try a lot harder to read the sink CRC until we get consistent values twice in a row before returning what we read and delay for a time before trying to read. We still see some occasional failures, but reading the sink CRC is much more reliable, particularly on SKL and KBL, with these changes than without.
Retrying seems like a good idea. But this patch retries up to 36 times if the two consecutive reads don't match, which is excessive.
The sleeps should probably be a separate change. Also not happy about the magic numbers there.
Also, there are plenty of what seem like unrelated changes. Whitespace, debug logging, error checking, etc.
BR,
Jani.
Quoted 151 lines
Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Jim Bride <[email protected]>--- drivers/gpu/drm/i915/i915_debugfs.c | 14 +++++++-- drivers/gpu/drm/i915/intel_dp.c | 57 ++++++++++++++++++++++++++++++++----- 2 files changed, 61 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/i915_debugfs.c +11
-3@@ -2718,7 +2718,7 @@ static int i915_sink_crc(struct seq_file *m, void *data)struct intel_connector *connector;struct drm_connector_list_iter conn_iter;struct intel_dp *intel_dp =NULL ; -int ret; +int ret, tries =6 ;u8 crc[6 ];drm_modeset_lock_all (dev);@@ -2738,9 +2738,17 @@ static int i915_sink_crc(struct seq_file *m, void *data) intel_dp =enc_to_intel_dp (connector->base.state->best_encoder); - ret =intel_dp_sink_crc (intel_dp, crc); -if (ret) +memset (crc,0 ,6 ); +do { + ret =intel_dp_sink_crc (intel_dp, crc); +if (ret == -ETIMEDOUT ) +usleep_range (500 ,700 ); + }while ((ret == -ETIMEDOUT ) && --tries); + +if (ret !=0 ) { +seq_printf (m,"000000000000\n" ); goto out; + } seq_printf(m, "%02x%02x%02x%02x%02x%02x\n", crc[0], crc[1], crc[2],drivers/gpu/drm/i915/intel_dp.c +50
-7@@ -3877,13 +3877,15 @@ static int intel_dp_sink_crc_stop(struct intel_dp *intel_dp)do {intel_wait_for_vblank (dev_priv, intel_crtc->pipe); - +usleep_range (16700 ,17000 );if (drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_SINK_MISC , &buf) <0 ) { +DRM_DEBUG_KMS ("Could not read TEST_SINK_MISC\n" ); ret = -EIO ; goto out; } count = buf &DP_TEST_COUNT_MASK ; +DRM_DEBUG_KMS ("PSR count is %d\n" , count); }while (--attempts && count);if (attempts ==0 ) {@@ -3928,6 +3930,8 @@ static int intel_dp_sink_crc_start(struct intel_dp *intel_dp) }intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16700 ,17000 ); +DRM_DEBUG_KMS ("PSR Successfully started sink CRC\n" );return 0 ; }@@ -3939,21 +3943,30 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc)u8 buf;int count, ret;int attempts =6 ; +u8 old_crc[6 ]; + +if (crc !=NULL ) +memset (crc,0 ,6 ); +else +return -ENOMEM ; ret =intel_dp_sink_crc_start (intel_dp); -if (ret) +if (ret) { +DRM_DEBUG_KMS ("Could not start sink crc; ret %d\n" , ret);return ret; + }do {intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16700 ,17000 );if (drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_SINK_MISC , &buf) <0 ) { +DRM_DEBUG_KMS ("Cound not read TEST_SINK_MISC\n" ); ret = -EIO ; goto stop; } count = buf &DP_TEST_COUNT_MASK ; - }while (--attempts && count ==0 );if (attempts ==0 ) {@@ -3962,11 +3975,41 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc) goto stop; } -if (drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_CRC_R_CR , crc,6 ) <0 ) { - ret = -EIO ; - goto stop; - } + attempts =6 ; +memset (old_crc,0xFF ,6 ); +do { +intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16500 ,17000 ); +if (drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_CRC_R_CR , + crc,6 ) <0 ) { +DRM_DEBUG_KMS ("Could not read sink crc\n" ); + ret = -EIO ; + goto stop; + } + +if (memcmp (old_crc, crc,6 ) ==0 ) { +DRM_DEBUG_KMS ("PSR Active: %3s Matching crc values found:" +"%02x%02x%02x%02x%02x%02x\n" , +yesno (dev_priv->psr.active), + crc[0 ], crc[1 ], crc[2 ], + crc[3 ], crc[4 ], crc[5 ]); + ret =0 ; + goto stop; + }else { +DRM_DEBUG_KMS ("PSR Active: %3s crc %02x%02x%02x%02x%02x%02x " +"doesn't match " +"previous %02x%02x%02x%02x%02x%02x\n" , +yesno (dev_priv->psr.active), + crc[0 ], crc[1 ], crc[2 ], + crc[3 ], crc[4 ], crc[5 ], + old_crc[0 ], old_crc[1 ], old_crc[2 ], + old_crc[3 ], old_crc[4 ], old_crc[5 ]); +memcpy (old_crc, crc,6 ); + } + }while (--attempts); +DRM_DEBUG_KMS ("Failed to get CRC after 6 attempts.\n" ); + ret = -ETIMEDOUT ; stop:intel_dp_sink_crc_stop (intel_dp);return ret;
Signature · 5 lines
Jani Nikula, Intel Open Source Technology Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/4] drm/i915/psr: Account for sink CRC raciness on some panels
Quoted 13 lines · Jani Nikula
Quoted 11 lines · Jim Bride
According to the eDP spec, when the count field in
TEST_SINK_MISCincrements then the six bytes of sink CRC information in the DPCD should be valid. Unfortunately, this doesn't seem to be the case on some panels, and as a result we get some incorrect and inconsistent values from the sink CRC DPCD locations at times. This problem exhibits itself more on faster processors (relative failure rates HSW < SKL < KBL.) In order to try and account for this, we try a lot harder to read the sink CRC until we get consistent values twice in a row before returning what we read and delay for a time before trying to read. We still see some occasional failures, but reading the sink CRC is much more reliable, particularly on SKL and KBL, with these changes than without.
Quoted 2 lines
Retrying seems like a good idea. But this patch retries up to 36 times if the two consecutive reads don't match, which is excessive.
I don't see where you're getting 36 from; the loop runs through six times.
Quoted 2 lines
The sleeps should probably be a separate change. Also not happy about the magic numbers there.
Looping w/o the sleeps doesn't make a ton of sense IMHO. The numbers were found experimentally on KBL, which seemed to more easily exercise the race that this patch is meant to address. Ideally the panels would not increment the counter until they were sure that the CRC data in the DPCD actually reflected reality. Unfortunately, this isn't what we're seeing. I will create a couple of #defines for the sleep values, at least, with some comments about them.
Quoted 2 lines
Also, there are plenty of what seem like unrelated changes. Whitespace, debug logging, error checking, etc.
I looked at this as refactoring the existing implementation, so I went ahead and added some debugging info; the error checking is part of the refactoring. Given the history of problems with this functionality that seemed warranted. I did notice one line of whitespace change that snuck in (where I missed that I removed a blank line.) I can take out the debug prints for the success cases if they seem excessive (and I'll restore the deleted blank line for the next version of the patch.)
Jim
Quoted 151 lines
BR,
Jani.Quoted 146 lines
Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Jim Bride <[email protected]>--- drivers/gpu/drm/i915/i915_debugfs.c | 14 +++++++-- drivers/gpu/drm/i915/intel_dp.c | 57 ++++++++++++++++++++++++++++++++----- 2 files changed, 61 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/i915_debugfs.c +11
-3@@ -2718,7 +2718,7 @@ static int i915_sink_crc(struct seq_file *m, void *data)struct intel_connector *connector;struct drm_connector_list_iter conn_iter;struct intel_dp *intel_dp =NULL ; -int ret; +int ret, tries =6 ;u8 crc[6 ];drm_modeset_lock_all (dev);@@ -2738,9 +2738,17 @@ static int i915_sink_crc(struct seq_file *m, void *data) intel_dp =enc_to_intel_dp (connector->base.state->best_encoder); - ret =intel_dp_sink_crc (intel_dp, crc); -if (ret) +memset (crc,0 ,6 ); +do { + ret =intel_dp_sink_crc (intel_dp, crc); +if (ret == -ETIMEDOUT ) +usleep_range (500 ,700 ); + }while ((ret == -ETIMEDOUT ) && --tries); + +if (ret !=0 ) { +seq_printf (m,"000000000000\n" ); goto out; + } seq_printf(m, "%02x%02x%02x%02x%02x%02x\n", crc[0], crc[1], crc[2],drivers/gpu/drm/i915/intel_dp.c +48
-7@@ -3877,13 +3877,15 @@ static int intel_dp_sink_crc_stop(struct intel_dp *intel_dp)do {intel_wait_for_vblank (dev_priv, intel_crtc->pipe); - +usleep_range (16700 ,17000 );if (drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_SINK_MISC , &buf) <0 ) { +DRM_DEBUG_KMS ("Could not read TEST_SINK_MISC\n" ); ret = -EIO ; goto out; } count = buf &DP_TEST_COUNT_MASK ; +DRM_DEBUG_KMS ("PSR count is %d\n" , count); }while (--attempts && count);if (attempts ==0 ) {@@ -3928,6 +3930,8 @@ static int intel_dp_sink_crc_start(struct intel_dp *intel_dp) }intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16700 ,17000 ); +DRM_DEBUG_KMS ("PSR Successfully started sink CRC\n" );return 0 ; }@@ -3939,21 +3943,30 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc)u8 buf;int count, ret;int attempts =6 ; +u8 old_crc[6 ]; + +if (crc !=NULL ) +memset (crc,0 ,6 ); +else +return -ENOMEM ; ret =intel_dp_sink_crc_start (intel_dp); -if (ret) +if (ret) { +DRM_DEBUG_KMS ("Could not start sink crc; ret %d\n" , ret);return ret; + }do {intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16700 ,17000 );if (drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_SINK_MISC , &buf) <0 ) { +DRM_DEBUG_KMS ("Cound not read TEST_SINK_MISC\n" ); ret = -EIO ; goto stop; } count = buf &DP_TEST_COUNT_MASK ; - }while (--attempts && count ==0 );if (attempts ==0 ) {@@ -3962,11 +3975,41 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc) goto stop; } -if (drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_CRC_R_CR , crc,6 ) <0 ) { - ret = -EIO ; - goto stop; - } + attempts =6 ; +memset (old_crc,0xFF ,6 ); +do { +intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16500 ,17000 ); +if (drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_CRC_R_CR , + crc,6 ) <0 ) { +DRM_DEBUG_KMS ("Could not read sink crc\n" ); + ret = -EIO ; + goto stop; + } + +if (memcmp (old_crc, crc,6 ) ==0 ) { +DRM_DEBUG_KMS ("PSR Active: %3s Matching crc values found:" +"%02x%02x%02x%02x%02x%02x\n" , +yesno (dev_priv->psr.active), + crc[0 ], crc[1 ], crc[2 ], + crc[3 ], crc[4 ], crc[5 ]); + ret =0 ; + goto stop; + }else { +DRM_DEBUG_KMS ("PSR Active: %3s crc %02x%02x%02x%02x%02x%02x " +"doesn't match " +"previous %02x%02x%02x%02x%02x%02x\n" , +yesno (dev_priv->psr.active), + crc[0 ], crc[1 ], crc[2 ], + crc[3 ], crc[4 ], crc[5 ], + old_crc[0 ], old_crc[1 ], old_crc[2 ], + old_crc[3 ], old_crc[4 ], old_crc[5 ]); +memcpy (old_crc, crc,6 ); + } + }while (--attempts);
Quoted 8 lines
Quoted 5 lines
drivers/gpu/drm/i915/intel_dp.c +2
-0+DRM_DEBUG_KMS ("Failed to get CRC after 6 attempts.\n" ); + ret = -ETIMEDOUT ; stop:intel_dp_sink_crc_stop (intel_dp);return ret;Signature · 1 line
Jani Nikula, Intel Open Source Technology Center
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Jani Nikula
maintainerRe: [PATCH 4/4] drm/i915/psr: Account for sink CRC raciness on some panels
Quoted 14 lines · Jim Bride
Quoted 13 lines · Jani Nikula
Quoted 11 lines · Jim Bride
According to the eDP spec, when the count field in
TEST_SINK_MISCincrements then the six bytes of sink CRC information in the DPCD should be valid. Unfortunately, this doesn't seem to be the case on some panels, and as a result we get some incorrect and inconsistent values from the sink CRC DPCD locations at times. This problem exhibits itself more on faster processors (relative failure rates HSW < SKL < KBL.) In order to try and account for this, we try a lot harder to read the sink CRC until we get consistent values twice in a row before returning what we read and delay for a time before trying to read. We still see some occasional failures, but reading the sink CRC is much more reliable, particularly on SKL and KBL, with these changes than without.
Quoted 4 lines
Quoted 2 lines
Retrying seems like a good idea. But this patch retries up to 36 times if the two consecutive reads don't match, which is excessive.
I don't see where you're getting 36 from; the loop runs through six times.
i915_sink_crc() calls intel_dp_sink_crc(), retrying on ETIMEDOUT. In turn, intel_dp_sink_crc() reads CRC, retrying on mismatched CRC and returning ETIMEDOUT to i915_sink_crc() on errors. Admittedly the loop in intel_dp_sink_crc() will always run at least twice to get two results to compare, so I guess it would be fair to say the combo tries CRC read up to 6 * 5 = 30 times.
Quoted 10 lines
Quoted 2 lines
The sleeps should probably be a separate change. Also not happy about the magic numbers there.
Looping w/o the sleeps doesn't make a ton of sense IMHO. The numbers were found experimentally on KBL, which seemed to more easily exercise the race that this patch is meant to address. Ideally the panels would not increment the counter until they were sure that the CRC data in the DPCD actually reflected reality. Unfortunately, this isn't what we're seeing. I will create a couple of #defines for the sleep values, at least, with some comments about them.
It's just that the magic sleeps are eerily close to a frame at 60 Hz. Did you try another vblank wait instead? Or maybe it's the sync to vblank that is the issue.
Quoted 11 lines
Quoted 2 lines
Also, there are plenty of what seem like unrelated changes. Whitespace, debug logging, error checking, etc.
I looked at this as refactoring the existing implementation, so I went ahead and added some debugging info; the error checking is part of the refactoring. Given the history of problems with this functionality that seemed warranted. I did notice one line of whitespace change that snuck in (where I missed that I removed a blank line.) I can take out the debug prints for the success cases if they seem excessive (and I'll restore the deleted blank line for the next version of the patch.)
The thing is, by now I'm looking at basically any sink visible functional changes to eDP, and PSR in particular, with the thought that this may have to be reverted due to regressions later. That has nothing to do with these patches, but rather our track record with eDP and PSR. (And that also says a lot about eDP sink quality in general.)
So I'd rather see the other changes split out so we have a smaller diff to revert, in case we have to revert. The pessimist does not get disappointed. And so far PSR hasn't given us any reasons for optimism.
BR,
Jani.
Quoted 163 lines
Jim
Quoted 159 lines
BR,
Jani.Quoted 151 lines
Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Jim Bride <[email protected]>--- drivers/gpu/drm/i915/i915_debugfs.c | 14 +++++++-- drivers/gpu/drm/i915/intel_dp.c | 57 ++++++++++++++++++++++++++++++++----- 2 files changed, 61 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/i915_debugfs.c +11
-3@@ -2718,7 +2718,7 @@ static int i915_sink_crc(struct seq_file *m, void *data)struct intel_connector *connector;struct drm_connector_list_iter conn_iter;struct intel_dp *intel_dp =NULL ; -int ret; +int ret, tries =6 ;u8 crc[6 ];drm_modeset_lock_all (dev);@@ -2738,9 +2738,17 @@ static int i915_sink_crc(struct seq_file *m, void *data) intel_dp =enc_to_intel_dp (connector->base.state->best_encoder); - ret =intel_dp_sink_crc (intel_dp, crc); -if (ret) +memset (crc,0 ,6 ); +do { + ret =intel_dp_sink_crc (intel_dp, crc); +if (ret == -ETIMEDOUT ) +usleep_range (500 ,700 ); + }while ((ret == -ETIMEDOUT ) && --tries); + +if (ret !=0 ) { +seq_printf (m,"000000000000\n" ); goto out; + } seq_printf(m, "%02x%02x%02x%02x%02x%02x\n", crc[0], crc[1], crc[2],drivers/gpu/drm/i915/intel_dp.c +50
-7@@ -3877,13 +3877,15 @@ static int intel_dp_sink_crc_stop(struct intel_dp *intel_dp)do {intel_wait_for_vblank (dev_priv, intel_crtc->pipe); - +usleep_range (16700 ,17000 );if (drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_SINK_MISC , &buf) <0 ) { +DRM_DEBUG_KMS ("Could not read TEST_SINK_MISC\n" ); ret = -EIO ; goto out; } count = buf &DP_TEST_COUNT_MASK ; +DRM_DEBUG_KMS ("PSR count is %d\n" , count); }while (--attempts && count);if (attempts ==0 ) {@@ -3928,6 +3930,8 @@ static int intel_dp_sink_crc_start(struct intel_dp *intel_dp) }intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16700 ,17000 ); +DRM_DEBUG_KMS ("PSR Successfully started sink CRC\n" );return 0 ; }@@ -3939,21 +3943,30 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc)u8 buf;int count, ret;int attempts =6 ; +u8 old_crc[6 ]; + +if (crc !=NULL ) +memset (crc,0 ,6 ); +else +return -ENOMEM ; ret =intel_dp_sink_crc_start (intel_dp); -if (ret) +if (ret) { +DRM_DEBUG_KMS ("Could not start sink crc; ret %d\n" , ret);return ret; + }do {intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16700 ,17000 );if (drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_SINK_MISC , &buf) <0 ) { +DRM_DEBUG_KMS ("Cound not read TEST_SINK_MISC\n" ); ret = -EIO ; goto stop; } count = buf &DP_TEST_COUNT_MASK ; - }while (--attempts && count ==0 );if (attempts ==0 ) {@@ -3962,11 +3975,41 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc) goto stop; } -if (drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_CRC_R_CR , crc,6 ) <0 ) { - ret = -EIO ; - goto stop; - } + attempts =6 ; +memset (old_crc,0xFF ,6 ); +do { +intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16500 ,17000 ); +if (drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_CRC_R_CR , + crc,6 ) <0 ) { +DRM_DEBUG_KMS ("Could not read sink crc\n" ); + ret = -EIO ; + goto stop; + } + +if (memcmp (old_crc, crc,6 ) ==0 ) { +DRM_DEBUG_KMS ("PSR Active: %3s Matching crc values found:" +"%02x%02x%02x%02x%02x%02x\n" , +yesno (dev_priv->psr.active), + crc[0 ], crc[1 ], crc[2 ], + crc[3 ], crc[4 ], crc[5 ]); + ret =0 ; + goto stop; + }else { +DRM_DEBUG_KMS ("PSR Active: %3s crc %02x%02x%02x%02x%02x%02x " +"doesn't match " +"previous %02x%02x%02x%02x%02x%02x\n" , +yesno (dev_priv->psr.active), + crc[0 ], crc[1 ], crc[2 ], + crc[3 ], crc[4 ], crc[5 ], + old_crc[0 ], old_crc[1 ], old_crc[2 ], + old_crc[3 ], old_crc[4 ], old_crc[5 ]); +memcpy (old_crc, crc,6 ); + } + }while (--attempts); +DRM_DEBUG_KMS ("Failed to get CRC after 6 attempts.\n" ); + ret = -ETIMEDOUT ; stop:intel_dp_sink_crc_stop (intel_dp);return ret;Signature · 1 line
Jani Nikula, Intel Open Source Technology Center
Signature · 5 lines
Jani Nikula, Intel Open Source Technology Center _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH 4/4] drm/i915/psr: Account for sink CRC raciness on some panels
Quoted 18 lines · Jani Nikula
Quoted 17 lines · Jim Bride
Quoted 15 lines · Jani Nikula
Quoted 11 lines · Jim Bride
According to the eDP spec, when the count field in
TEST_SINK_MISCincrements then the six bytes of sink CRC information in the DPCD should be valid. Unfortunately, this doesn't seem to be the case on some panels, and as a result we get some incorrect and inconsistent values from the sink CRC DPCD locations at times. This problem exhibits itself more on faster processors (relative failure rates HSW < SKL < KBL.) In order to try and account for this, we try a lot harder to read the sink CRC until we get consistent values twice in a row before returning what we read and delay for a time before trying to read. We still see some occasional failures, but reading the sink CRC is much more reliable, particularly on SKL and KBL, with these changes than without.Retrying seems like a good idea. But this patch retries up to 36 times if the two consecutive reads don't match, which is excessive.
Quoted 8 lines
Quoted 1 line
I don't see where you're getting 36 from; the loop runs through six times.
i915_sink_crc()callsintel_dp_sink_crc(), retrying on ETIMEDOUT. In turn,intel_dp_sink_crc()reads CRC, retrying on mismatched CRC and returning ETIMEDOUT toi915_sink_crc()on errors. Admittedly the loop inintel_dp_sink_crc()will always run at least twice to get two results to compare, so I guess it would be fair to say the combo tries CRC read up to 6 * 5 = 30 times.
I'll play around with making i915_sink_crc() a little less persistent and see what it does. The loop in intel_dp_sink_crc() frequently goes 3+ tries, so I'd prefer to keep that one as it is.
Quoted 11 lines
Quoted 10 lines
Quoted 2 lines
The sleeps should probably be a separate change. Also not happy about the magic numbers there.
Looping w/o the sleeps doesn't make a ton of sense IMHO. The numbers were found experimentally on KBL, which seemed to more easily exercise the race that this patch is meant to address. Ideally the panels would not increment the counter until they were sure that the CRC data in the DPCD actually reflected reality. Unfortunately, this isn't what we're seeing. I will create a couple of #defines for the sleep values, at least, with some comments about them.
Quoted 3 lines
It's just that the magic sleeps are eerily close to a frame at 60 Hz. Did you try another vblank wait instead? Or maybe it's the sync to vblank that is the issue.
This brings up an interesting point. IMHO relying on vblanks for PSR related stuff is a bad idea, at least while PSR is active. The reason I say this is that if PSR is active, then the link itself may or may not be active. We certainly shouldn't be sending frames of data, vblanks, or anything of that ilk. There's a patch series that Rodrigo wrote last August that I plan to write a IGT test case for (I wanted to see IGT working right for PSR tests in general before doing this) that basically makes sure that vblanks are disabled if PSR is active, and that enabling vblanks causes PSR to exit. Review feedback on that series was that it needed an IGT test. When thinking about this series, I've been toying with the idea of doing a sleep based on the time needed to render a frame + the appropriate blanking intervals instead of doing all of the vblank waits anyhow, at least for the sink CRC stuff since we need to get that data out while PSR is active. Now I'm wondering if we should go ahead and do that for all but the PSR exit case now, perhaps. Thoughts?
Quoted 18 lines
Quoted 11 lines
Quoted 2 lines
Also, there are plenty of what seem like unrelated changes. Whitespace, debug logging, error checking, etc.
I looked at this as refactoring the existing implementation, so I went ahead and added some debugging info; the error checking is part of the refactoring. Given the history of problems with this functionality that seemed warranted. I did notice one line of whitespace change that snuck in (where I missed that I removed a blank line.) I can take out the debug prints for the success cases if they seem excessive (and I'll restore the deleted blank line for the next version of the patch.)
The thing is, by now I'm looking at basically any sink visible functional changes to eDP, and PSR in particular, with the thought that this may have to be reverted due to regressions later. That has nothing to do with these patches, but rather our track record with eDP and PSR. (And that also says a lot about eDP sink quality in general.)
Quoted 3 lines
So I'd rather see the other changes split out so we have a smaller diff to revert, in case we have to revert. The pessimist does not get disappointed. And so far PSR hasn't given us any reasons for optimism.
Let me see what I can do. I might be able to at least split out some of the debug / error checking into a separate patch.
Jim
Quoted 160 lines
BR,
Jani.Quoted 155 lines
Jim
Quoted 151 lines
BR,
Jani.Quoted 146 lines
Cc Rodrigo Vivi <[email protected]>Cc Paulo Zanoni <[email protected]>Signed-off-by Jim Bride <[email protected]>--- drivers/gpu/drm/i915/i915_debugfs.c | 14 +++++++-- drivers/gpu/drm/i915/intel_dp.c | 57 ++++++++++++++++++++++++++++++++----- 2 files changed, 61 insertions(+), 10 deletions(-)drivers/gpu/drm/i915/i915_debugfs.c +11
-3@@ -2718,7 +2718,7 @@ static int i915_sink_crc(struct seq_file *m, void *data)struct intel_connector *connector;struct drm_connector_list_iter conn_iter;struct intel_dp *intel_dp =NULL ; -int ret; +int ret, tries =6 ;u8 crc[6 ];drm_modeset_lock_all (dev);@@ -2738,9 +2738,17 @@ static int i915_sink_crc(struct seq_file *m, void *data) intel_dp =enc_to_intel_dp (connector->base.state->best_encoder); - ret =intel_dp_sink_crc (intel_dp, crc); -if (ret) +memset (crc,0 ,6 ); +do { + ret =intel_dp_sink_crc (intel_dp, crc); +if (ret == -ETIMEDOUT ) +usleep_range (500 ,700 ); + }while ((ret == -ETIMEDOUT ) && --tries); + +if (ret !=0 ) { +seq_printf (m,"000000000000\n" ); goto out; + } seq_printf(m, "%02x%02x%02x%02x%02x%02x\n", crc[0], crc[1], crc[2],drivers/gpu/drm/i915/intel_dp.c +48
-7@@ -3877,13 +3877,15 @@ static int intel_dp_sink_crc_stop(struct intel_dp *intel_dp)do {intel_wait_for_vblank (dev_priv, intel_crtc->pipe); - +usleep_range (16700 ,17000 );if (drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_SINK_MISC , &buf) <0 ) { +DRM_DEBUG_KMS ("Could not read TEST_SINK_MISC\n" ); ret = -EIO ; goto out; } count = buf &DP_TEST_COUNT_MASK ; +DRM_DEBUG_KMS ("PSR count is %d\n" , count); }while (--attempts && count);if (attempts ==0 ) {@@ -3928,6 +3930,8 @@ static int intel_dp_sink_crc_start(struct intel_dp *intel_dp) }intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16700 ,17000 ); +DRM_DEBUG_KMS ("PSR Successfully started sink CRC\n" );return 0 ; }@@ -3939,21 +3943,30 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc)u8 buf;int count, ret;int attempts =6 ; +u8 old_crc[6 ]; + +if (crc !=NULL ) +memset (crc,0 ,6 ); +else +return -ENOMEM ; ret =intel_dp_sink_crc_start (intel_dp); -if (ret) +if (ret) { +DRM_DEBUG_KMS ("Could not start sink crc; ret %d\n" , ret);return ret; + }do {intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16700 ,17000 );if (drm_dp_dpcd_readb (&intel_dp->aux,DP_TEST_SINK_MISC , &buf) <0 ) { +DRM_DEBUG_KMS ("Cound not read TEST_SINK_MISC\n" ); ret = -EIO ; goto stop; } count = buf &DP_TEST_COUNT_MASK ; - }while (--attempts && count ==0 );if (attempts ==0 ) {@@ -3962,11 +3975,41 @@ int intel_dp_sink_crc(struct intel_dp *intel_dp, u8 *crc) goto stop; } -if (drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_CRC_R_CR , crc,6 ) <0 ) { - ret = -EIO ; - goto stop; - } + attempts =6 ; +memset (old_crc,0xFF ,6 ); +do { +intel_wait_for_vblank (dev_priv, intel_crtc->pipe); +usleep_range (16500 ,17000 ); +if (drm_dp_dpcd_read (&intel_dp->aux,DP_TEST_CRC_R_CR , + crc,6 ) <0 ) { +DRM_DEBUG_KMS ("Could not read sink crc\n" ); + ret = -EIO ; + goto stop; + } + +if (memcmp (old_crc, crc,6 ) ==0 ) { +DRM_DEBUG_KMS ("PSR Active: %3s Matching crc values found:" +"%02x%02x%02x%02x%02x%02x\n" , +yesno (dev_priv->psr.active), + crc[0 ], crc[1 ], crc[2 ], + crc[3 ], crc[4 ], crc[5 ]); + ret =0 ; + goto stop; + }else { +DRM_DEBUG_KMS ("PSR Active: %3s crc %02x%02x%02x%02x%02x%02x " +"doesn't match " +"previous %02x%02x%02x%02x%02x%02x\n" , +yesno (dev_priv->psr.active), + crc[0 ], crc[1 ], crc[2 ], + crc[3 ], crc[4 ], crc[5 ], + old_crc[0 ], old_crc[1 ], old_crc[2 ], + old_crc[3 ], old_crc[4 ], old_crc[5 ]); +memcpy (old_crc, crc,6 ); + } + }while (--attempts);
Quoted 11 lines
Quoted 8 lines
Quoted 8 lines
Quoted 5 lines
drivers/gpu/drm/i915/intel_dp.c +2
-0+DRM_DEBUG_KMS ("Failed to get CRC after 6 attempts.\n" ); + ret = -ETIMEDOUT ; stop:intel_dp_sink_crc_stop (intel_dp);return ret;Signature · 1 line
Jani Nikula, Intel Open Source Technology CenterSignature · 1 line
Jani Nikula, Intel Open Source Technology Center
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for Kernel PSR Fix-ups
In reply to Jim Bride== Series Details ==
== Series Details ==
Series: Kernel PSR Fix-ups
URL : https://patchwork.freedesktop.org/series/24049/
State : success
== Summary ==
Series 24049v1 Kernel PSR Fix-ups
https://patchwork.freedesktop.org/api/1.0/series/24049/revisions/1/mbox/
Test gem_exec_flush:
Subgroup basic-batch-kernel-default-uc:
fail -> PASS (fi-snb-2600) fdo#100007fdo#100007 https://bugs.freedesktop.org/show_bug.cgi?id=100007
fi-bdw-5557u total:278 pass:267 dwarn:0 dfail:0 fail:0 skip:11 time:432s fi-bdw-gvtdvm total:278 pass:256 dwarn:8 dfail:0 fail:0 skip:14 time:427s fi-bxt-j4205 total:278 pass:259 dwarn:0 dfail:0 fail:0 skip:19 time:508s fi-bxt-t5700 total:278 pass:258 dwarn:0 dfail:0 fail:0 skip:20 time:531s fi-byt-j1900 total:278 pass:254 dwarn:0 dfail:0 fail:0 skip:24 time:489s fi-byt-n2820 total:278 pass:250 dwarn:0 dfail:0 fail:0 skip:28 time:488s fi-hsw-4770 total:278 pass:262 dwarn:0 dfail:0 fail:0 skip:16 time:410s fi-hsw-4770r total:278 pass:262 dwarn:0 dfail:0 fail:0 skip:16 time:413s fi-ilk-650 total:278 pass:228 dwarn:0 dfail:0 fail:0 skip:50 time:416s fi-ivb-3520m total:278 pass:260 dwarn:0 dfail:0 fail:0 skip:18 time:480s fi-ivb-3770 total:278 pass:260 dwarn:0 dfail:0 fail:0 skip:18 time:476s fi-kbl-7500u total:278 pass:260 dwarn:0 dfail:0 fail:0 skip:18 time:456s fi-kbl-7560u total:278 pass:267 dwarn:1 dfail:0 fail:0 skip:10 time:577s fi-skl-6260u total:278 pass:268 dwarn:0 dfail:0 fail:0 skip:10 time:456s fi-skl-6700k total:278 pass:256 dwarn:4 dfail:0 fail:0 skip:18 time:456s fi-skl-6770hq total:278 pass:268 dwarn:0 dfail:0 fail:0 skip:10 time:489s fi-skl-gvtdvm total:278 pass:265 dwarn:0 dfail:0 fail:0 skip:13 time:428s fi-snb-2520m total:278 pass:250 dwarn:0 dfail:0 fail:0 skip:28 time:527s fi-snb-2600 total:278 pass:249 dwarn:0 dfail:0 fail:0 skip:29 time:402s
fi-bsw-n3050 failed to collect. IGT log at Patchwork_4633/fi-bsw-n3050/igt.log
fb550f86433515f36a0de161631541ec114581e3 drm-tip: 2017y-05m-05d-18h-33m-52s UTC integration manifest 46a8d3e drm/i915/psr: Account for sink CRC raciness on some panels
829bb88 drm/i915/edp: Be less aggressive about changing link config on eDP
a1d3407 drm/i915/psr: Clean-up intel_enable_source_psr1()
b74b07c drm/i915/edp: Allow alternate fixed mode for eDP if available.
== Logs ==
For more details see: https://intel-gfx-ci.01.org/CI/Patchwork_4633/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx