arm: dts: imx7: sync with Linux
Subsystems (7)
Peng Fan
reviewerPATCH v2 1/12 arm: dts: imx7: sync with Linux
Sync with Linux commit 308ac756("Merge tag 'gpio-v4.11-3'").
Signed-off-by Peng Fan <[email protected]>
Cc Stefan Agner <[email protected]>
Cc Stefano Babic <[email protected]>
---
V2:
remove imx7.dtsi
arch/arm/dts/imx7-colibri.dts | 10 +- arch/arm/dts/imx7.dtsi | 194 ------- arch/arm/dts/imx7d-pinfunc.h | 111 ++-- arch/arm/dts/imx7d.dtsi | 140 +++++ arch/arm/dts/imx7s.dtsi | 999 ++++++++++++++++++++++++++++++++ include/dt-bindings/clock/imx7d-clock.h | 454 +++++++++++++++ 6 files changed, 1657 insertions(+), 251 deletions(-) delete mode 100644 arch/arm/dts/imx7.dtsi create mode 100644 arch/arm/dts/imx7d.dtsi create mode 100644 arch/arm/dts/imx7s.dtsi create mode 100644 include/dt-bindings/clock/imx7d-clock.h
arch/arm/dts/imx7-colibri.dts +5 -5
@@ -6,7 +6,7 @@ /dts-v1/; #include <dt-bindings/gpio/gpio.h> -#include "imx7.dtsi" +#include "imx7d.dtsi" / { model = "Toradex Colibri iMX7S/D";
@@ -83,15 +83,15 @@ &iomuxc_lpsr { pinctrl_i2c1: i2c1-grp { fsl,pins = < - MX7D_PAD_GPIO1_IO05__I2C1_SDA 0x4000007f - MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f + MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA 0x4000007f + MX7D_PAD_LPSR_GPIO1_IO04__I2C1_SCL 0x4000007f >; }; pinctrl_i2c1_gpio: i2c1-gpio-grp { fsl,pins = < - MX7D_PAD_GPIO1_IO05__GPIO1_IO5 0x4000007f - MX7D_PAD_GPIO1_IO04__GPIO1_IO4 0x4000007f + MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5 0x4000007f + MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4 0x4000007f >; }; };
arch/arm/dts/imx7.dtsi deleted +0 -194
194 lines not on this page · raw message
arch/arm/dts/imx7d-pinfunc.h +59 -52
123 lines not on this page · raw message
arch/arm/dts/imx7d.dtsi new file +140 -0
140 lines not on this page · raw message
arch/arm/dts/imx7s.dtsi new file +999 -0
999 lines not on this page · raw message
include/dt-bindings/clock/imx7d-clock.h new file +454 -0
454 lines not on this page · raw message
Signature · 1 line
2.6.2
Peng Fan
reviewerPATCH v2 2/12 arm: dts: imx7d-sdb add basic dts
Add basic dts for i.MX7D-SDB board.
Signed-off-by Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
V2:
Drop dts file from NXP vendor tree.
arch/arm/dts/Makefile | 3 ++- arch/arm/dts/imx7d-sdb.dts | 19 +++++++++++++++++++ configs/mx7dsabresd_defconfig | 3 ++- 3 files changed, 23 insertions(+), 2 deletions(-) create mode 100644 arch/arm/dts/imx7d-sdb.dts
arch/arm/dts/Makefile +2 -1
@@ -325,7 +325,8 @@ dtb-$(CONFIG_MX6) += imx6ull-14x14-evk.dtb \ imx6ul-isiot-nand.dtb \ imx6ul-opos6uldev.dtb -dtb-$(CONFIG_MX7) += imx7-colibri.dtb +dtb-$(CONFIG_MX7) += imx7-colibri.dtb \ + imx7d-sdb.dtb dtb-$(CONFIG_ARCH_MX7ULP) += imx7ulp-evk.dtb
arch/arm/dts/imx7d-sdb.dts new file +19 -0
@@ -0,0 +1,19 @@ +/* + * Copyright 2017 NXP + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/dts-v1/; + +#include "imx7d.dtsi" + +/ { + model = "Freescale i.MX7 SabreSD Board"; + compatible = "fsl,imx7d-sdb", "fsl,imx7d"; + + memory { + reg = <0x80000000 0x80000000>; + }; + +};
configs/mx7dsabresd_defconfig +2 -1
@@ -5,6 +5,7 @@ CONFIG_TARGET_MX7DSABRESD=y CONFIG_IMX_RDC=y CONFIG_IMX_BOOTAUX=y CONFIG_VIDEO=y +CONFIG_DEFAULT_DEVICE_TREE="imx7d-sdb" CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7dsabresd/imximage.cfg" CONFIG_BOOTDELAY=3 # CONFIG_CONSOLE_MUX is not set
@@ -32,6 +33,7 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_FAT=y +CONFIG_OF_CONTROL=y CONFIG_DFU_MMC=y CONFIG_DFU_RAM=y CONFIG_USB=y
@@ -44,4 +46,3 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="FSL" CONFIG_G_DNL_VENDOR_NUM=0x0525 CONFIG_G_DNL_PRODUCT_NUM=0xa4a5 -CONFIG_OF_LIBFDT=y
Signature · 1 line
2.6.2
Peng Fan
reviewerPATCH v2 3/12 arm: dts: imx7d-sdb: add spi gpio node
In reply to Peng FanAdd spi gpio node for 74LV595.
Signed-off-by Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
V2:
New
arch/arm/dts/imx7d-sdb.dts | 35 +++++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/arm/dts/imx7d-sdb.dts +35 -0
@@ -16,4 +16,39 @@ reg = <0x80000000 0x80000000>; }; + spi4 { + compatible = "spi-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1>; + status = "okay"; + gpio-sck = <&gpio1 13 0>; + gpio-mosi = <&gpio1 9 0>; + cs-gpios = <&gpio1 12 0>; + num-chipselects = <1>; + #address-cells = <1>; + #size-cells = <0>; + + gpio_spi: gpio_spi at 0 { + compatible = "fairchild,74hc595"; + gpio-controller; + #gpio-cells = <2>; + reg = <0>; + registers-number = <1>; + registers-default = /bits/ 8 <0x74>; /* Enable PERI_3V3, SENSOR_RST_B and HDMI_RST*/ + spi-max-frequency = <100000>; + }; + }; +}; + +&iomuxc { + imx7d-sdb { + pinctrl_spi1: spi1grp { + fsl,pins = < + MX7D_PAD_GPIO1_IO09__GPIO1_IO9 0x59 + MX7D_PAD_GPIO1_IO12__GPIO1_IO12 0x59 + MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x59 + >; + }; + }; + };
Signature · 1 line
2.6.2
Peng Fan
reviewerPATCH v2 4/12 arm: dts: imx7d-sdb: add regulator node for usb and mmc
In reply to Peng FanAdd regulator node for usb and mmc.
Signed-off-by Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
V2:
New
arch/arm/dts/imx7d-sdb.dts | 36 ++++++++++++++++++++++++++++++++++++ 1 file changed, 36 insertions(+)
arch/arm/dts/imx7d-sdb.dts +36 -0
@@ -38,6 +38,42 @@ spi-max-frequency = <100000>; }; }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_usb_otg1_vbus: regulator at 0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg2_vbus: regulator at 1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "usb_otg2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_sd1_vmmc: regulator at 3 { + compatible = "regulator-fixed"; + regulator-name = "VDD_SD1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>; + startup-delay-us = <200000>; + enable-active-high; + }; + }; }; &iomuxc {
Signature · 1 line
2.6.2
Peng Fan
reviewerPATCH v2 5/12 arm: dts: imx7d-sdb: add i2c support
In reply to Peng FanAdd i2c support.
Signed-off-by Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
V2:
New
arch/arm/dts/imx7d-sdb.dts | 146 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 146 insertions(+)
arch/arm/dts/imx7d-sdb.dts +146 -0
@@ -85,6 +85,152 @@ MX7D_PAD_GPIO1_IO13__GPIO1_IO13 0x59 >; }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX7D_PAD_I2C1_SDA__I2C1_SDA 0x4000007f + MX7D_PAD_I2C1_SCL__I2C1_SCL 0x4000007f + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX7D_PAD_I2C2_SDA__I2C2_SDA 0x4000007f + MX7D_PAD_I2C2_SCL__I2C2_SCL 0x4000007f + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX7D_PAD_I2C3_SDA__I2C3_SDA 0x4000007f + MX7D_PAD_I2C3_SCL__I2C3_SCL 0x4000007f + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA 0x4000007f + MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL 0x4000007f + >; + }; }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic: pfuze3000 at 08 { + compatible = "fsl,pfuze3000"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1a { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + /* use sw1c_reg to align with pfuze100/pfuze200 */ + sw1c_reg: sw1b { + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1475000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1850000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1650000>; + regulator-boot-on; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen2_reg: vldo2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + regulator-always-on; + }; + + vgen3_reg: vccsd { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen4_reg: v33 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vldo4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; +&i2c4 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; };
Signature · 1 line
2.6.2
Peng Fan
reviewerPATCH v2 6/12 arm: dts: imx7d-sdb: add usdhc support
In reply to Peng FanAdd usdhc support
Signed-off-by Peng Fan <[email protected]>
---
V2:
New
arch/arm/dts/imx7d-sdb.dts | 73 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 73 insertions(+)
arch/arm/dts/imx7d-sdb.dts +73 -0
@@ -113,6 +113,55 @@ MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL 0x4000007f >; }; + + pinctrl_usdhc1_gpio: usdhc1_gpiogrp { + fsl,pins = < + MX7D_PAD_SD1_CD_B__GPIO5_IO0 0x59 /* CD */ + MX7D_PAD_SD1_WP__GPIO5_IO1 0x59 /* WP */ + MX7D_PAD_SD1_RESET_B__GPIO5_IO2 0x59 /* vmmc */ + MX7D_PAD_GPIO1_IO08__SD1_VSELECT 0x59 /* VSELECT */ + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX7D_PAD_SD1_CMD__SD1_CMD 0x59 + MX7D_PAD_SD1_CLK__SD1_CLK 0x19 + MX7D_PAD_SD1_DATA0__SD1_DATA0 0x59 + MX7D_PAD_SD1_DATA1__SD1_DATA1 0x59 + MX7D_PAD_SD1_DATA2__SD1_DATA2 0x59 + MX7D_PAD_SD1_DATA3__SD1_DATA3 0x59 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX7D_PAD_SD2_CMD__SD2_CMD 0x59 + MX7D_PAD_SD2_CLK__SD2_CLK 0x19 + MX7D_PAD_SD2_DATA0__SD2_DATA0 0x59 + MX7D_PAD_SD2_DATA1__SD2_DATA1 0x59 + MX7D_PAD_SD2_DATA2__SD2_DATA2 0x59 + MX7D_PAD_SD2_DATA3__SD2_DATA3 0x59 + MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21 0x19 /* WL_REG_ON */ + MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20 0x19 /* WL_HOST_WAKE */ + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX7D_PAD_SD3_CMD__SD3_CMD 0x59 + MX7D_PAD_SD3_CLK__SD3_CLK 0x19 + MX7D_PAD_SD3_DATA0__SD3_DATA0 0x59 + MX7D_PAD_SD3_DATA1__SD3_DATA1 0x59 + MX7D_PAD_SD3_DATA2__SD3_DATA2 0x59 + MX7D_PAD_SD3_DATA3__SD3_DATA3 0x59 + MX7D_PAD_SD3_DATA4__SD3_DATA4 0x59 + MX7D_PAD_SD3_DATA5__SD3_DATA5 0x59 + MX7D_PAD_SD3_DATA6__SD3_DATA6 0x59 + MX7D_PAD_SD3_DATA7__SD3_DATA7 0x59 + MX7D_PAD_SD3_STROBE__SD3_STROBE 0x19 + >; + }; }; };
@@ -234,3 +283,27 @@ pinctrl-0 = <&pinctrl_i2c4>; status = "okay"; }; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>; + cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; + vmmc-supply = <®_sd1_vmmc>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + non-removable; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + bus-width = <8>; + non-removable; + status = "okay"; +};
Signature · 1 line
2.6.2
Peng Fan
reviewerPATCH v2 7/12 spi: kconfig: add soft spi Kconfig entry
In reply to Peng FanAdd the Kconfig entry for SOFT_SPI which uses gpio to simulate the SPI signals. We use it for accessing 74x164 on some i.MX boards.
Signed-off-by Peng Fan <[email protected]>
Cc Jagan Teki <[email protected]>
Cc Stefano Babic <[email protected]>
---
V2:
None
drivers/spi/Kconfig | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/spi/Kconfig +6 -0
@@ -197,6 +197,12 @@ config OMAP3_SPI endif # if DM_SPI +config SOFT_SPI + bool "Soft SPI driver" + help + Enable Soft SPI driver. This driver is to use GPIO simulate + the SPI protocol. + config FSL_ESPI bool "Freescale eSPI driver" help
Signature · 1 line
2.6.2
PATCH v2 7/12 spi: kconfig: add soft spi Kconfig entry
Quoted 19 lines · Peng Fan
Add the
Kconfigentry forSOFT_SPIwhich uses gpio to simulate the SPI signals. We use it for accessing 74x164 on some i.MX boards.Signed-off-by Peng Fan <[email protected]>Cc Jagan Teki <[email protected]>Cc Stefano Babic <[email protected]>---
V2:
Nonedrivers/spi/Kconfig | 6 ++++++ 1 file changed, 6 insertions(+)drivers/spi/Kconfig +0
-0
drivers/spi/Kconfig config OMAP3_SPI · line 201
Quoted 5 lines
drivers/spi/Kconfig +2
-0@@ -197,6 +197,12 @@ config OMAP3_SPI endif # if DM_SPI +config SOFT_SPI + bool "Soft SPI driver"
Did you move this for dm-driven file? since we've two files with same config
drivers/spi/Kconfig config OMAP3_SPI · line 204
Quoted 3 lines
drivers/spi/Kconfig +3
-0+ help + Enable Soft SPI driver. This driver is to use GPIO simulate + the SPI protocol.
If possible please write few lines about this
thanks!
Signature · 4 lines
Jagan Teki Free Software Engineer | www.openedev.com U-Boot, Linux | Upstream Maintainer Hyderabad, India.
PATCH v2 7/12 spi: kconfig: add soft spi Kconfig entry
Quoted 21 lines · Jagan Teki
Quoted 20 lines · Peng Fan
Add the
Kconfigentry forSOFT_SPIwhich uses gpio to simulate the SPI signals. We use it for accessing 74x164 on some i.MX boards.Signed-off-by Peng Fan <[email protected]>Cc Jagan Teki <[email protected]>Cc Stefano Babic <[email protected]>---
V2:
Nonedrivers/spi/Kconfig | 6 ++++++ 1 file changed, 6 insertions(+)drivers/spi/Kconfig +0
-0@@ -197,6 +197,12 @@ config OMAP3_SPI
Quoted 6 lines
drivers/spi/Kconfig config OMAP3_SPI · line 201
Quoted 4 lines
drivers/spi/Kconfig +2
-0endif # if DM_SPI +config SOFT_SPI + bool "Soft SPI driver"Did you move this for dm-driven file? since we've two files with same config
This config is for dm and non-dm both.
Quoted 6 lines
drivers/spi/Kconfig config OMAP3_SPI · line 204
Quoted 4 lines
drivers/spi/Kconfig +3
-0+ help + Enable Soft SPI driver. This driver is to use GPIO simulate + the SPI protocol.If possible please write few lines about this
I understand this two line help message will trigger check patch warning, but I think this is clear to tell user what this option is.
Thanks,
Peng.
Quoted 11 lines
thanks!
Signature · 8 lines
Jagan Teki Free Software Engineer | www.openedev.com U-Boot, Linux | Upstream Maintainer Hyderabad, India. _______________________________________________ U-Boot mailing list U-Boot at lists.denx.de https://lists.denx.de/listinfo/u-boot
Peng Fan
reviewerPATCH v2 8/12 gpio: 74x164: make oe-pins optional
In reply to Peng FanMake oe-pins optional because some boards have fixed it to enable.
Signed-off-by Peng Fan <[email protected]>
Cc Simon Glass <[email protected]>
Cc Stefano Babic <[email protected]>
---
V2:
None
drivers/gpio/74x164_gpio.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/gpio/74x164_gpio.c +1 -2
@@ -156,8 +156,7 @@ static int gen_74x164_probe(struct udevice *dev) ret =gpio_request_by_name (dev,"oe-gpios" ,0 , &priv->oe,GPIOD_IS_OUT |GPIOD_IS_OUT_ACTIVE );if (ret) { -dev_err (dev,"No oe-pins property\n" ); - goto free_buf; +dev_dbg (dev,"No oe-pins property\n" ); } uc_priv->bank_name = str;
Signature · 1 line
2.6.2
PATCH v2 8/12 gpio: 74x164: make oe-pins optional
Quoted 5 lines · Peng Fan
Make oe-pins optional because some boards have fixed it to enable.
Signed-off-by Peng Fan <[email protected]>Cc Simon Glass <[email protected]>Cc Stefano Babic <[email protected]>
Quoted 7 lines
---
V2:
Nonedrivers/gpio/74x164_gpio.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
Reviewed-by Simon Glass <[email protected]>
Peng Fan
reviewerPATCH v2 9/12 imx: mx7dsabresd: enable more DM drivers
In reply to Peng FanEnable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO enabled. The 74x164 drivers needs SOFT_SPI and DM_GPIO enabled. So needs to enable them together.
Signed-off-by Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
V2:
None
board/freescale/mx7dsabresd/mx7dsabresd.c | 288 ++---------------------------- configs/mx7dsabresd_defconfig | 21 +++ include/configs/mx7dsabresd.h | 11 -- 3 files changed, 37 insertions(+), 283 deletions(-)
board/freescale/mx7dsabresd/mx7dsabresd.c +16 -272
@@ -31,17 +31,11 @@ DECLARE_GLOBAL_DATA_PTR;#define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | \ PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS) -#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \ - PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM) -#define ENET_PAD_CTRL (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)#define ENET_PAD_CTRL_MII (PAD_CTL_DSE_3P3V_32OHM)#define ENET_RX_PAD_CTRL (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM) -#define I2C_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \ - PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM) -#define LCD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_PU100KOHM | \ PAD_CTL_DSE_3P3V_49OHM)
@@ -54,23 +48,8 @@ DECLARE_GLOBAL_DATA_PTR; (PAD_CTL_HYS | PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_FAST)#define NAND_PAD_READY0_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU5KOHM) -#ifdef CONFIG_SYS_I2C_MXC -#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) -/* I2C1 for PMIC */ -static struct i2c_pads_info i2c_pad_info1 = { - .scl = { - .i2c_mode =MX7D_PAD_I2C1_SCL__I2C1_SCL |PC , - .gpio_mode =MX7D_PAD_I2C1_SCL__GPIO4_IO8 |PC , - .gp =IMX_GPIO_NR (4 ,8 ), - }, - .sda = { - .i2c_mode =MX7D_PAD_I2C1_SDA__I2C1_SDA |PC , - .gpio_mode =MX7D_PAD_I2C1_SDA__GPIO4_IO9 |PC , - .gp =IMX_GPIO_NR (4 ,9 ), - }, -}; -#endif +#ifdef CONFIG_MXC_SPI static iomux_v3_cfg_t const ecspi3_pads[] = {MX7D_PAD_SAI2_RX_DATA__ECSPI3_SCLK |MUX_PAD_CTRL (SPI_PAD_CTRL ), MX7D_PAD_SAI2_TX_SYNC__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
@@ -87,6 +66,7 @@ static void setup_spi(void) {imx_iomux_v3_setup_multiple_pads (ecspi3_pads,ARRAY_SIZE (ecspi3_pads)); } +#endif int dram_init (void ) {
@@ -104,34 +84,6 @@ static iomux_v3_cfg_t const uart1_pads[] = { MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), }; -static iomux_v3_cfg_t const usdhc1_pads[] = { -MX7D_PAD_SD1_CLK__SD1_CLK |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD1_CMD__SD1_CMD |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD1_DATA0__SD1_DATA0 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD1_DATA1__SD1_DATA1 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD1_DATA2__SD1_DATA2 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD1_DATA3__SD1_DATA3 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), - -MX7D_PAD_SD1_CD_B__GPIO5_IO0 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD1_RESET_B__GPIO5_IO2 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -}; - -static iomux_v3_cfg_t const usdhc3_emmc_pads[] = { -MX7D_PAD_SD3_CLK__SD3_CLK |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD3_CMD__SD3_CMD |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD3_DATA0__SD3_DATA0 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD3_DATA1__SD3_DATA1 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD3_DATA2__SD3_DATA2 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD3_DATA3__SD3_DATA3 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD3_DATA4__SD3_DATA4 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD3_DATA5__SD3_DATA5 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD3_DATA6__SD3_DATA6 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD3_DATA7__SD3_DATA7 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -MX7D_PAD_SD3_STROBE__SD3_STROBE |MUX_PAD_CTRL (USDHC_PAD_CTRL ), - -MX7D_PAD_SD3_RESET_B__GPIO6_IO11 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), -}; -static iomux_v3_cfg_t const usb_otg1_pads[] = {MX7D_PAD_GPIO1_IO05__USB_OTG1_PWR |MUX_PAD_CTRL (NO_PAD_CTRL ), };
@@ -140,94 +92,6 @@ static iomux_v3_cfg_t const usb_otg2_pads[] = { MX7D_PAD_UART3_CTS_B__USB_OTG2_PWR | MUX_PAD_CTRL(NO_PAD_CTRL), }; -#define IOX_SDI IMX_GPIO_NR(1, 9) -#define IOX_STCP IMX_GPIO_NR(1, 12) -#define IOX_SHCP IMX_GPIO_NR(1, 13) - -static iomux_v3_cfg_t const iox_pads[] = { -/* IOX_SDI */ -MX7D_PAD_GPIO1_IO09__GPIO1_IO9 |MUX_PAD_CTRL (NO_PAD_CTRL ), -/* IOX_STCP */ -MX7D_PAD_GPIO1_IO12__GPIO1_IO12 |MUX_PAD_CTRL (NO_PAD_CTRL ), -/* IOX_SHCP */ -MX7D_PAD_GPIO1_IO13__GPIO1_IO13 |MUX_PAD_CTRL (NO_PAD_CTRL ), -}; - -/* -* PCIE_DIS_B --> Q0 -* PCIE_RST_B --> Q1 -* HDMI_RST_B --> Q2 -* PERI_RST_B --> Q3 -* SENSOR_RST_B --> Q4 -* ENET_RST_B --> Q5 -* PERI_3V3_EN --> Q6 -* LCD_PWR_EN --> Q7 -*/ -enum qn { -PCIE_DIS_B , -PCIE_RST_B , -HDMI_RST_B , -PERI_RST_B , -SENSOR_RST_B , -ENET_RST_B , -PERI_3V3_EN , -LCD_PWR_EN , -}; - -enum qn_func { - qn_reset, - qn_enable, - qn_disable, -}; - -enum qn_level { - qn_low =0 , - qn_high =1 , -}; - -static enum qn_level seq[3 ][2 ] = { - {0 ,1 }, {1 ,1 }, {0 ,0 } -}; - -static enum qn_func qn_output[8 ] = { - qn_disable, qn_reset, qn_reset, qn_reset, qn_reset, qn_reset, qn_enable, - qn_disable -}; - -static void iox74lv_init (void ) -{ -int i; - -for (i =7 ; i >=0 ; i--) { -gpio_direction_output (IOX_SHCP ,0 ); -gpio_direction_output (IOX_SDI , seq[qn_output[i]][0 ]); -udelay (500 ); -gpio_direction_output (IOX_SHCP ,1 ); -udelay (500 ); - } - -gpio_direction_output (IOX_STCP ,0 ); -udelay (500 ); -/* -* shift register will be output to pins -*/ -gpio_direction_output (IOX_STCP ,1 ); - -for (i =7 ; i >=0 ; i--) { -gpio_direction_output (IOX_SHCP ,0 ); -gpio_direction_output (IOX_SDI , seq[qn_output[i]][1 ]); -udelay (500 ); -gpio_direction_output (IOX_SHCP ,1 ); -udelay (500 ); - } -gpio_direction_output (IOX_STCP ,0 ); -udelay (500 ); -/* -* shift register will be output to pins -*/ -gpio_direction_output (IOX_STCP ,1 ); -}; -#ifdef CONFIG_NAND_MXS static iomux_v3_cfg_t const gpmi_pads[] = { MX7D_PAD_SD3_DATA0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
@@ -306,11 +170,13 @@ static int setup_lcd(void)imx_iomux_v3_setup_multiple_pads (pwm_pads,ARRAY_SIZE (pwm_pads));/* Reset LCD */ +gpio_request (IMX_GPIO_NR (3 ,4 ),"lcd reset" );gpio_direction_output (IMX_GPIO_NR (3 ,4 ) ,0 );udelay (500 );gpio_direction_output (IMX_GPIO_NR (3 ,4 ) ,1 );/* Set Brightness to high */ +gpio_request (IMX_GPIO_NR (1 ,1 ),"lcd backlight" );gpio_direction_output (IMX_GPIO_NR (1 ,1 ) ,1 );return 0 ;
@@ -346,17 +212,6 @@ static void setup_iomux_uart(void)imx_iomux_v3_setup_multiple_pads (uart1_pads,ARRAY_SIZE (uart1_pads)); } -#ifdef CONFIG_FSL_ESDHC - -#define USDHC1_CD_GPIO IMX_GPIO_NR(5, 0) -#define USDHC1_PWR_GPIO IMX_GPIO_NR(5, 2) -#define USDHC3_PWR_GPIO IMX_GPIO_NR(6, 11) - -static struct fsl_esdhc_cfg usdhc_cfg[3 ] = { - {USDHC1_BASE_ADDR ,0 ,4 }, - {USDHC3_BASE_ADDR }, -}; -int board_mmc_get_env_dev (int devno) {if (devno ==2 )
@@ -365,7 +220,7 @@ int board_mmc_get_env_dev(int devno)return devno; } -static int mmc_map_to_kernel_blk (int dev_no) +int mmc_map_to_kernel_blk (int dev_no) {if (dev_no ==1 ) dev_no++;
@@ -373,102 +228,6 @@ static int mmc_map_to_kernel_blk(int dev_no)return dev_no; } -int board_mmc_getcd (struct mmc *mmc) -{ -struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; -int ret =0 ; - -switch (cfg->esdhc_base) { -case USDHC1_BASE_ADDR : - ret = !gpio_get_value (USDHC1_CD_GPIO ); -break ; -case USDHC3_BASE_ADDR : - ret =1 ;/* Assume uSDHC3 emmc is always present */ -break ; - } - -return ret; -} - -int board_mmc_init (bd_t *bis) -{ -int i, ret; -/* -* According to the board_mmc_init() the following map is done: -* (U-Boot device node) (Physical Port) -* mmc0 USDHC1 -* mmc2 USDHC3 (eMMC) -*/ -for (i =0 ; i <CONFIG_SYS_FSL_USDHC_NUM ; i++) { -switch (i) { -case 0 : -imx_iomux_v3_setup_multiple_pads ( - usdhc1_pads,ARRAY_SIZE (usdhc1_pads)); -gpio_request (USDHC1_CD_GPIO ,"usdhc1_cd" ); -gpio_direction_input (USDHC1_CD_GPIO ); -gpio_request (USDHC1_PWR_GPIO ,"usdhc1_pwr" ); -gpio_direction_output (USDHC1_PWR_GPIO ,0 ); -udelay (500 ); -gpio_direction_output (USDHC1_PWR_GPIO ,1 ); - usdhc_cfg[0 ].sdhc_clk =mxc_get_clock (MXC_ESDHC_CLK ); -break ; -case 1 : -imx_iomux_v3_setup_multiple_pads ( - usdhc3_emmc_pads,ARRAY_SIZE (usdhc3_emmc_pads)); -gpio_request (USDHC3_PWR_GPIO ,"usdhc3_pwr" ); -gpio_direction_output (USDHC3_PWR_GPIO ,0 ); -udelay (500 ); -gpio_direction_output (USDHC3_PWR_GPIO ,1 ); - usdhc_cfg[1 ].sdhc_clk =mxc_get_clock (MXC_ESDHC3_CLK ); -break ; -default : -printf ("Warning: you configured more USDHC controllers" -"(%d) than supported by the board\n" , i +1 ); -return -EINVAL ; - } - - ret =fsl_esdhc_initialize (bis, &usdhc_cfg[i]); -if (ret) -return ret; - } - -return 0 ; -} - -static int check_mmc_autodetect (void ) -{ -char *autodetect_str =getenv ("mmcautodetect" ); - -if ((autodetect_str !=NULL ) && - (strcmp (autodetect_str,"yes" ) ==0 )) { -return 1 ; - } - -return 0 ; -} - -static void mmc_late_init (void ) -{ -char cmd[32 ]; -char mmcblk[32 ]; -u32 dev_no =mmc_get_env_dev (); - -if (!check_mmc_autodetect ()) -return ; - -setenv_ulong ("mmcdev" , dev_no); - -/* Set mmcblk env */ -sprintf (mmcblk,"/dev/mmcblk%dp2 rootwait rw" , -mmc_map_to_kernel_blk (dev_no)); -setenv ("mmcroot" , mmcblk); - -sprintf (cmd,"mmc dev %d" , dev_no); -run_command (cmd,0 ); -} - -#endif -#ifdef CONFIG_FEC_MXC int board_eth_init (bd_t *bis) {
@@ -539,7 +298,6 @@ int board_early_init_f(void) {setup_iomux_uart (); -setup_i2c (0 ,CONFIG_SYS_I2C_SPEED ,0x7f , &i2c_pad_info1);imx_iomux_v3_setup_multiple_pads (usb_otg1_pads,ARRAY_SIZE (usb_otg1_pads)); imx_iomux_v3_setup_multiple_pads(usb_otg2_pads,
@@ -553,10 +311,6 @@ int board_init(void)/* address of boot parameters */ gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; -imx_iomux_v3_setup_multiple_pads (iox_pads,ARRAY_SIZE (iox_pads)); - -iox74lv_init (); -#ifdef CONFIG_FEC_MXC setup_fec ();#endif
@@ -580,29 +334,23 @@ int board_init(void)return 0 ; } -#ifdef CONFIG_POWER -#define I2C_PMIC 0 +#ifdef CONFIG_DM_PMIC int power_init_board (void ) { -struct pmic *p; -int ret; -unsigned int reg, rev_id; +struct udevice *dev; +int ret, dev_id, rev_id; - ret =power_pfuze3000_init (I2C_PMIC ); -if (ret) + ret =pmic_get ("pfuze3000" , &dev); +if (ret == -ENODEV ) +return 0 ; +if (ret !=0 )return ret; - p =pmic_get ("PFUZE3000" ); - ret =pmic_probe (p); -if (ret) -return ret; - -pmic_reg_read (p,PFUZE3000_DEVICEID , ®); -pmic_reg_read (p,PFUZE3000_REVID , &rev_id); -printf ("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n" , reg, rev_id); + dev_id =pmic_reg_read (dev,PFUZE3000_DEVICEID ); + rev_id =pmic_reg_read (dev,PFUZE3000_REVID ); +printf ("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n" , dev_id, rev_id); -/* disable Low Power Mode during standby mode */ -pmic_reg_write (p,PFUZE3000_LDOGCTL ,0x1 ); +pmic_clrsetbits (dev,PFUZE3000_LDOGCTL ,0 ,1 );return 0 ; }
@@ -612,10 +360,6 @@ int board_late_init(void) {struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR ; -#ifdef CONFIG_ENV_IS_IN_MMC -mmc_late_init (); -#endif -imx_iomux_v3_setup_multiple_pads (wdog_pads,ARRAY_SIZE (wdog_pads));set_wdog_reset (wdog);
configs/mx7dsabresd_defconfig +21 -0
@@ -29,13 +29,33 @@ CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y +CONFIG_CMD_PMIC=y +CONFIG_CMD_REGULATOR=y CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_FAT=y CONFIG_OF_CONTROL=y +# CONFIG_BLK is not set CONFIG_DFU_MMC=y CONFIG_DFU_RAM=y +CONFIG_DM_GPIO=y +CONFIG_DM_74X164=y +CONFIG_DM_I2C=y +CONFIG_DM_MMC=y +# CONFIG_DM_MMC_OPS is not set +CONFIG_SPI_FLASH=y +CONFIG_SPI_FLASH_EON=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX7=y +CONFIG_DM_PMIC=y +CONFIG_DM_PMIC_PFUZE100=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_PFUZE100=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_DM_SPI=y +CONFIG_SOFT_SPI=y CONFIG_USB=y CONFIG_USB_EHCI_HCD=y CONFIG_MXC_USB_OTG_HACTIVE=y
@@ -46,3 +66,4 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="FSL" CONFIG_G_DNL_VENDOR_NUM=0x0525 CONFIG_G_DNL_PRODUCT_NUM=0xa4a5 +CONFIG_ERRNO_STR=y
include/configs/mx7dsabresd.h +0 -11
@@ -34,20 +34,12 @@/* MMC Config*/ #define CONFIG_SYS_FSL_ESDHC_ADDR 0 -/* PMIC */ -#define CONFIG_POWER -#define CONFIG_POWER_I2C -#define CONFIG_POWER_PFUZE3000 -#define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08 -#undef CONFIG_BOOTM_NETBSD#undef CONFIG_BOOTM_PLAN9#undef CONFIG_BOOTM_RTEMS/* I2C configs */ -#define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ #define CONFIG_SYS_I2C_SPEED 100000#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
@@ -197,9 +189,6 @@#define CONFIG_ENV_SIZE SZ_8K#define CONFIG_ENV_IS_IN_MMC -/* MXC SPI driver support */ -#define CONFIG_MXC_SPI -/* * If want to use nand, define CONFIG_NAND_MXS and rework board * to support nand, since emmc has pin conflicts with nand
Signature · 1 line
2.6.2
PATCH v2 9/12 imx: mx7dsabresd: enable more DM drivers
Hi Peng,
Quoted 6 lines · Peng Fan
Enable more DM drivers. The imx I2C/MMC DM drivers needs
DM_GPIOenabled. The 74x164 drivers needsSOFT_SPIandDM_GPIOenabled. So needs to enable them together.Signed-off-by Peng Fan <[email protected]>Cc Stefano Babic <[email protected]>
Quoted 7 lines
---
V2:
Noneboard/freescale/mx7dsabresd/mx7dsabresd.c | 288 ++---------------------------- configs/mx7dsabresd_defconfig | 21 +++
This does not patch mx7dsabresd_secure_defconfig, that results then broken. I have just fixed in my local branch and I send a patch for it (I can just test build).
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
Peng Fan
reviewerPATCH v2 10/12 imx: mx7dsabresd: reset ENET_RST_B
In reply to Peng FanReset ENET_RST_B to make ENET function stable.
Since DM_GPIO enabled, we use "gpio_spi at 0_5" which corresponds to ENET_RST_B.
Signed-off-by Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
V2:
None
board/freescale/mx7dsabresd/mx7dsabresd.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
board/freescale/mx7dsabresd/mx7dsabresd.c +17 -0
@@ -232,6 +232,23 @@ int mmc_map_to_kernel_blk(int dev_no)int board_eth_init (bd_t *bis) {int ret; +unsigned int gpio; + + ret =gpio_lookup_name ("gpio_spi at 0_5" ,NULL ,NULL , &gpio); +if (ret) { +printf ("GPIO: 'gpio_spi at 0_5' not found\n" ); +return -ENODEV ; + } + + ret =gpio_request (gpio,"fec_rst" ); +if (ret && ret != -EBUSY ) { +printf ("gpio: requesting pin %u failed\n" , gpio); +return ret; + } + +gpio_direction_output (gpio,0 ); +udelay (500 ); +gpio_direction_output (gpio,1 );setup_iomux_fec ();
Signature · 1 line
2.6.2
Peng Fan
reviewerPATCH v2 11/12 imx: mx7dsabresd: switch to DM USB
In reply to Peng FanSwitch to use DM USB.
Signed-off-by Peng Fan <[email protected]>
--- board/freescale/mx7dsabresd/mx7dsabresd.c | 25 ------------------------- configs/mx7dsabresd_defconfig | 1 + include/configs/mx7dsabresd.h | 3 --- 3 files changed, 1 insertion(+), 28 deletions(-)
board/freescale/mx7dsabresd/mx7dsabresd.c +0 -25
@@ -23,8 +23,6 @@#include <i2c.h> #include <asm/imx-common/mxc_i2c.h> #include <asm/arch/crm_regs.h> -#include <usb.h> -#include <usb/ehci-ci.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -84,14 +82,6 @@ static iomux_v3_cfg_t const uart1_pads[] = { MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), }; -static iomux_v3_cfg_t const usb_otg1_pads[] = { -MX7D_PAD_GPIO1_IO05__USB_OTG1_PWR |MUX_PAD_CTRL (NO_PAD_CTRL ), -}; - -static iomux_v3_cfg_t const usb_otg2_pads[] = { -MX7D_PAD_UART3_CTS_B__USB_OTG2_PWR |MUX_PAD_CTRL (NO_PAD_CTRL ), -}; -#ifdef CONFIG_NAND_MXS static iomux_v3_cfg_t const gpmi_pads[] = { MX7D_PAD_SD3_DATA0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
@@ -315,11 +305,6 @@ int board_early_init_f(void) {setup_iomux_uart (); -imx_iomux_v3_setup_multiple_pads (usb_otg1_pads, -ARRAY_SIZE (usb_otg1_pads)); -imx_iomux_v3_setup_multiple_pads (usb_otg2_pads, -ARRAY_SIZE (usb_otg2_pads)); -return 0 ; }
@@ -403,13 +388,3 @@ int checkboard(void)return 0 ; } - -#ifdef CONFIG_USB_EHCI_MX7 -int board_usb_phy_mode (int port) -{ -if (port ==0 ) -return USB_INIT_DEVICE ; -else -return USB_INIT_HOST ; -} -#endif
configs/mx7dsabresd_defconfig +1 -0
@@ -57,6 +57,7 @@ CONFIG_DM_REGULATOR_GPIO=y CONFIG_DM_SPI=y CONFIG_SOFT_SPI=y CONFIG_USB=y +CONFIG_DM_USB=y CONFIG_USB_EHCI_HCD=y CONFIG_MXC_USB_OTG_HACTIVE=y CONFIG_USB_STORAGE=y
include/configs/mx7dsabresd.h +0 -3
@@ -221,12 +221,9 @@#define CONFIG_MMCROOT "/dev/mmcblk0p2"/* USDHC1 */ /* USB Configs */ -#define CONFIG_EHCI_HCD_INIT_AFTER_RESET #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) -#define CONFIG_MXC_USB_FLAGS 0 -#define CONFIG_USB_MAX_CONTROLLER_COUNT 2#define CONFIG_IMX_THERMAL
Signature · 1 line
2.6.2
Peng Fan
reviewerPATCH v2 12/12 imx: mx7dsabresd: add board revision check
In reply to Peng FanAdd board revision check
Signed-off-by Peng Fan <[email protected]>
--- board/freescale/mx7dsabresd/mx7dsabresd.c | 59 ++++++++++++++++++++++++++++++- 1 file changed, 58 insertions(+), 1 deletion(-)
board/freescale/mx7dsabresd/mx7dsabresd.c +58 -1
@@ -82,6 +82,48 @@ static iomux_v3_cfg_t const uart1_pads[] = { MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL), }; +#define BOARD_REV_C 0x300 +#define BOARD_REV_B 0x200 +#define BOARD_REV_A 0x100 + +static int mx7sabre_rev (void ) +{ +/* +* Get Board ID information from OCOTP_GP1[15:8] +* i.MX7D SDB RevA: 0x41 +* i.MX7D SDB RevB: 0x42 +*/ +struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR ; +struct fuse_bank *bank = &ocotp->bank[14 ]; +int reg =readl (&bank->fuse_regs[0 ]); +int ret; + +if (reg !=0 ) { +switch (reg >>8 &0x0F ) { +case 0x3 : + ret =BOARD_REV_C ; +break ; +case 0x02 : + ret =BOARD_REV_B ; +break ; +case 0x01 : +default : + ret =BOARD_REV_A ; +break ; + } + }else { +/* If the gp1 fuse is not burn, we have to use TO rev for the board rev */ +if (is_soc_rev (CHIP_REV_1_0 )) + ret =BOARD_REV_A ; +else if (is_soc_rev (CHIP_REV_1_1 )) + ret =BOARD_REV_B ; +else + ret =BOARD_REV_C ; + } + +return ret; +} +#ifdef CONFIG_NAND_MXS static iomux_v3_cfg_t const gpmi_pads[] = { MX7D_PAD_SD3_DATA0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
@@ -377,14 +419,29 @@ int board_late_init(void)int checkboard (void ) { +int rev =mx7sabre_rev ();char *mode; +char *revname;if (IS_ENABLED (CONFIG_ARMV7_BOOT_SEC_DEFAULT )) mode ="secure" ;else mode ="non-secure" ; -printf ("Board: i.MX7D SABRESD in %s mode\n" , mode); +switch (rev) { +case BOARD_REV_C : + revname ="C" ; +break ; +case BOARD_REV_B : + revname ="B" ; +break ; +case BOARD_REV_A : +default : + revname ="A" ; +break ; + } + +printf ("Board: i.MX7D SABRESD Rev%s in %s mode\n" , revname, mode);return 0 ; }
Signature · 1 line
2.6.2
Fabio Estevam
reviewerPATCH v2 12/12 imx: mx7dsabresd: add board revision check
board/freescale/mx7dsabresd/mx7dsabresd.c static iomux_v3_cfg_t const uart1_pads[] = { · line 94
Quoted 10 lines · Peng Fan
board/freescale/mx7dsabresd/mx7dsabresd.c +10
-0+#define BOARD_REV_C 0x300 +#define BOARD_REV_B 0x200 +#define BOARD_REV_A 0x100 + +static int mx7sabre_rev (void ) +{ +/* +* Get Board ID information from OCOTP_GP1[15:8] +* i.MX7D SDB RevA: 0x41 +* i.MX7D SDB RevB: 0x42
Isn't this versioning scheme shared with other NXP boards? If so, it would be better to put this in common code.
Peng Fan
reviewerPATCH v2 12/12 imx: mx7dsabresd: add board revision check
Hi Fabio,
Quoted 10 lines
-----Original Message-----
From: Fabio Estevam [mailto:festevam at gmail.com]
Sent: Monday, April 17, 2017 11:00 PM
To: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>; U-Boot-Denx <[email protected]>
Subject: Re: [U-Boot] [PATCH V2 12/12] imx: mx7dsabresd: add board revision checkOn Thu, Apr 13, 2017 at 3:10 AM, Peng Fan <[email protected]> wrote:
Quoted 13 lines
board/freescale/mx7dsabresd/mx7dsabresd.c static iomux_v3_cfg_t const uart1_pads[] = { · line 94
Quoted 10 lines
board/freescale/mx7dsabresd/mx7dsabresd.c +10
-0+#define BOARD_REV_C 0x300 +#define BOARD_REV_B 0x200 +#define BOARD_REV_A 0x100 + +static int mx7sabre_rev (void ) +{ +/* +* Get Board ID information from OCOTP_GP1[15:8] +* i.MX7D SDB RevA: 0x41 +* i.MX7D SDB RevB: 0x42 Isn't this versioning scheme shared with other NXP boards? If so, it would be better to put this in common code.
I prefer to keep the code here. There are board revision fuse for the boards from NXP, but this is not always true, I think.
Thanks,
Peng.
PATCH v2 12/12 imx: mx7dsabresd: add board revision check
Hi Peng,
Quoted 26 lines · Peng Fan
Hi Fabio,
Quoted 10 lines
-----Original Message-----
From: Fabio Estevam [mailto:festevam at gmail.com]
Sent: Monday, April 17, 2017 11:00 PM
To: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>; U-Boot-Denx <[email protected]>
Subject: Re: [U-Boot] [PATCH V2 12/12] imx: mx7dsabresd: add board revision checkOn Thu, Apr 13, 2017 at 3:10 AM, Peng Fan <[email protected]> wrote:
Quoted 13 lines
board/freescale/mx7dsabresd/mx7dsabresd.c static iomux_v3_cfg_t const uart1_pads[] = { · line 94
Quoted 10 lines
board/freescale/mx7dsabresd/mx7dsabresd.c +10
-0+#define BOARD_REV_C 0x300 +#define BOARD_REV_B 0x200 +#define BOARD_REV_A 0x100 + +static int mx7sabre_rev (void ) +{ +/* +* Get Board ID information from OCOTP_GP1[15:8] +* i.MX7D SDB RevA: 0x41 +* i.MX7D SDB RevB: 0x42 Isn't this versioning scheme shared with other NXP boards? If so, it would be better to put this in common code.
Quoted 2 lines
I prefer to keep the code here. There are board revision fuse for the boards from NXP, but this is not always true, I think.
Anyway, there is "quite" same code for mx6 sabre:
static int mx6sabre_rev(void)
{
/*
* Get Board ID information from OCOTP_GP1[15:8]
* i.MX6Q ARD RevA: 0x01
* i.MX6Q ARD RevB: 0x02
*/
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
struct fuse_bank *bank = &ocotp->bank[4];
struct fuse_bank4_regs *fuse =
(struct fuse_bank4_regs *)bank->fuse_regs;
int reg = readl(&fuse->gp1);
int ret;
switch (reg >> 8 & 0x0F) {
case 0x02:
ret = BOARD_REV_B;
break;
case 0x01:
default:And the version number is simple an integer and we do not need to add defines - if we simply returns the read value (1,2,3,..), the code works even with future versions. Are you sure that this is not at least "sabre common code " ?
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
Peng Fan
reviewerPATCH v2 12/12 imx: mx7dsabresd: add board revision check
Hi Stefano,
Quoted 64 lines
-----Original Message-----
From: Stefano Babic [mailto:sbabic at denx.de]
Sent: Thursday, May 11, 2017 7:33 PM
To: Peng Fan <[email protected]>; Fabio Estevam <[email protected]>
Cc: Stefano Babic <[email protected]>; U-Boot-Denx <[email protected]>
Subject: Re: [U-Boot] [PATCH V2 12/12] imx: mx7dsabresd: add board revision checkHi Peng,
Quoted 27 lines · Peng Fan
Hi Fabio,
Quoted 11 lines
-----Original Message-----
From: Fabio Estevam [mailto:festevam at gmail.com]
Sent: Monday, April 17, 2017 11:00 PM
To: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>; U-Boot-Denx <[email protected]>
Subject: Re: [U-Boot] [PATCH V2 12/12] imx: mx7dsabresd: add board revision checkOn Thu, Apr 13, 2017 at 3:10 AM, Peng Fan <[email protected]> wrote:
Quoted 13 lines
board/freescale/mx7dsabresd/mx7dsabresd.c static iomux_v3_cfg_t const uart1_pads[] = { · line 94
Quoted 10 lines
board/freescale/mx7dsabresd/mx7dsabresd.c +10
-0+#define BOARD_REV_C 0x300 +#define BOARD_REV_B 0x200 +#define BOARD_REV_A 0x100 + +static int mx7sabre_rev (void ) +{ +/* +* Get Board ID information from OCOTP_GP1[15:8] +* i.MX7D SDB RevA: 0x41 +* i.MX7D SDB RevB: 0x42 Isn't this versioning scheme shared with other NXP boards? If so, it would be better to put this in common code.
Quoted 2 lines
I prefer to keep the code here. There are board revision fuse for the boards from NXP, but this is not always true, I think.
Anyway, there is "quite" same code for mx6 sabre:
static int
mx6sabre_rev(void){ /* * Get Board ID information from OCOTP_GP1[15:8] * i.MX6Q ARD RevA: 0x01 * i.MX6Q ARD RevB: 0x02 */ struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; struct fuse_bank *bank = &ocotp->bank[4]; struct fuse_bank4_regs *fuse = (struct fuse_bank4_regs *)bank->fuse_regs; int reg = readl(&fuse->gp1); int ret; switch (reg >> 8 & 0x0F) { case 0x02: ret = BOARD_REV_B; break; case 0x01: default:
Quoted 4 lines
And the version number is simple an integer and we do not need to add defines - if we simply returns the read value (1,2,3,..), the code works even with future versions. Are you sure that this is not at least "sabre common code " ?
Could I use a follow up patch to move the revision check to a common place? I would not send a whole V3 patch set if no more comments.
Thanks,
Peng.
Quoted 12 lines
Regards,
Stefano--
============================================================
=========
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
============================================================
=========
PATCH v2 12/12 imx: mx7dsabresd: add board revision check
In reply to Peng FanHi Peng,
Quoted 26 lines · Peng Fan
Hi Fabio,
Quoted 10 lines
-----Original Message-----
From: Fabio Estevam [mailto:festevam at gmail.com]
Sent: Monday, April 17, 2017 11:00 PM
To: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>; U-Boot-Denx <[email protected]>
Subject: Re: [U-Boot] [PATCH V2 12/12] imx: mx7dsabresd: add board revision checkOn Thu, Apr 13, 2017 at 3:10 AM, Peng Fan <[email protected]> wrote:
Quoted 13 lines
board/freescale/mx7dsabresd/mx7dsabresd.c static iomux_v3_cfg_t const uart1_pads[] = { · line 94
Quoted 10 lines
board/freescale/mx7dsabresd/mx7dsabresd.c +10
-0+#define BOARD_REV_C 0x300 +#define BOARD_REV_B 0x200 +#define BOARD_REV_A 0x100 + +static int mx7sabre_rev (void ) +{ +/* +* Get Board ID information from OCOTP_GP1[15:8] +* i.MX7D SDB RevA: 0x41 +* i.MX7D SDB RevB: 0x42 Isn't this versioning scheme shared with other NXP boards? If so, it would be better to put this in common code.
Quoted 3 lines
I prefer to keep the code here. There are board revision fuse for the boards from NXP, but this is not always true, I think.
Patches 1..11 are free of comments. I am merging them and I will send PR to Tom for inclusion after my build test. I will just let this last one out.
Regards,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
Peng Fan
reviewerPATCH v2 12/12 imx: mx7dsabresd: add board revision check
Quoted 11 lines
-----Original Message-----
From: Stefano Babic [mailto:sbabic at denx.de]
Sent: Thursday, May 18, 2017 4:20 PM
To: Peng Fan <[email protected]>; Fabio Estevam <[email protected]>
Cc: Stefano Babic <[email protected]>; U-Boot-Denx <[email protected]>
Subject: Re: [U-Boot] [PATCH V2 12/12] imx: mx7dsabresd: add board revision checkHi Peng,
Hi Stefano,
Quoted 29 lines · Peng Fan
Quoted 27 lines
Hi Fabio,
Quoted 24 lines
-----Original Message-----
From: Fabio Estevam [mailto:festevam at gmail.com]
Sent: Monday, April 17, 2017 11:00 PM
To: Peng Fan <[email protected]>
Cc: Stefano Babic <[email protected]>; U-Boot-Denx <[email protected]>
Subject: Re: [U-Boot] [PATCH V2 12/12] imx: mx7dsabresd: add board revision checkboard/freescale/mx7dsabresd/mx7dsabresd.c static iomux_v3_cfg_t const uart1_pads[] = { · line 94
Quoted 10 lines · Peng Fan
board/freescale/mx7dsabresd/mx7dsabresd.c +10
-0+#define BOARD_REV_C 0x300 +#define BOARD_REV_B 0x200 +#define BOARD_REV_A 0x100 + +static int mx7sabre_rev (void ) +{ +/* +* Get Board ID information from OCOTP_GP1[15:8] +* i.MX7D SDB RevA: 0x41 +* i.MX7D SDB RevB: 0x42 Isn't this versioning scheme shared with other NXP boards? If so, it would be better to put this in common code.
Quoted 6 lines
Quoted 3 lines
I prefer to keep the code here. There are board revision fuse for the boards from NXP, but this is not always true, I think.
Patches 1..11 are free of comments. I am merging them and I will send PR to Tom for inclusion after my build test. I will just let this last one out.
It is ok for me to let this out. Thanks.
Thanks,
Peng.
Quoted 13 lines
Regards,
Stefano--
============================================================
=========
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
============================================================
=========
PATCH v2 12/12 imx: mx7dsabresd: add board revision check
Quoted 4 lines · Peng Fan
Quoted 2 lines
Patches 1..11 are free of comments. I am merging them and I will send PR to Tom for inclusion after my build test. I will just let this last one out.
It is ok for me to let this out. Thanks.
ok - just check with patch I send today to fix the "secure" variant, then I could insert this to my PR.
Thanks,
Stefano
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v2 1/12 arm: dts: imx7: sync with Linux
In reply to Peng FanQuoted 9 lines · Peng Fan
Sync with Linux commit 308ac756("Merge tag 'gpio-v4.11-3'").
Signed-off-by Peng Fan <[email protected]>Cc Stefan Agner <[email protected]>Cc Stefano Babic <[email protected]>---
V2:
removeimx7.dtsi
Reviewed-by Stefano Babic <[email protected]>
Regards,
Stefano
Quoted 1,987 lines
arch/arm/dts/imx7-colibri.dts | 10 +- arch/arm/dts/imx7.dtsi | 194 ------- arch/arm/dts/imx7d-pinfunc.h | 111 ++-- arch/arm/dts/imx7d.dtsi | 140 +++++ arch/arm/dts/imx7s.dtsi | 999 ++++++++++++++++++++++++++++++++ include/dt-bindings/clock/imx7d-clock.h | 454 +++++++++++++++ 6 files changed, 1657 insertions(+), 251 deletions(-) delete mode 100644 arch/arm/dts/imx7.dtsi create mode 100644 arch/arm/dts/imx7d.dtsi create mode 100644 arch/arm/dts/imx7s.dtsi create mode 100644 include/dt-bindings/clock/imx7d-clock.harch/arm/dts/imx7-colibri.dts +5
-5@@ -6,7 +6,7 @@ /dts-v1/; #include <dt-bindings/gpio/gpio.h> -#include "imx7.dtsi" +#include "imx7d.dtsi" / { model = "Toradex Colibri iMX7S/D";@@ -83,15 +83,15 @@ &iomuxc_lpsr { pinctrl_i2c1: i2c1-grp { fsl,pins = < - MX7D_PAD_GPIO1_IO05__I2C1_SDA 0x4000007f - MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x4000007f + MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA 0x4000007f + MX7D_PAD_LPSR_GPIO1_IO04__I2C1_SCL 0x4000007f >; }; pinctrl_i2c1_gpio: i2c1-gpio-grp { fsl,pins = < - MX7D_PAD_GPIO1_IO05__GPIO1_IO5 0x4000007f - MX7D_PAD_GPIO1_IO04__GPIO1_IO4 0x4000007f + MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5 0x4000007f + MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4 0x4000007f >; }; };arch/arm/dts/imx7.dtsi deleted +0
-194@@ -1,194 +0,0 @@ -/* - * Copyright 2016 Toradex AG - * - * SPDX-License-Identifier: GPL-2.0+ or X11 - */ -#include "imx7d-pinfunc.h" -#include "skeleton.dtsi" - -/ { - aliases { - gpio0 = &gpio1; - gpio1 = &gpio2; - gpio2 = &gpio3; - gpio3 = &gpio4; - gpio4 = &gpio5; - gpio5 = &gpio6; - gpio6 = &gpio7; - i2c0 = &i2c1; - i2c1 = &i2c2; - i2c2 = &i2c3; - i2c3 = &i2c4; - serial0 = &uart1; - serial1 = &uart2; - serial2 = &uart3; - serial3 = &uart4; - serial4 = &uart5; - serial5 = &uart6; - serial6 = &uart7; - }; - - soc { - #address-cells = <1>; - #size-cells = <1>; - compatible = "simple-bus"; - ranges; - - aips1: aips-bus at 30000000 { - compatible = "fsl,aips-bus", "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x30000000 0x400000>; - ranges; - - gpio1: gpio at 30200000 { - compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; - reg = <0x30200000 0x10000>; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio2: gpio at 30210000 { - compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; - reg = <0x30210000 0x10000>; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio3: gpio at 30220000 { - compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; - reg = <0x30220000 0x10000>; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio4: gpio at 30230000 { - compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; - reg = <0x30230000 0x10000>; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio5: gpio at 30240000 { - compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; - reg = <0x30240000 0x10000>; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio6: gpio at 30250000 { - compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; - reg = <0x30250000 0x10000>; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio7: gpio at 30260000 { - compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; - reg = <0x30260000 0x10000>; - gpio-controller; - #gpio-cells = <2>; - }; - - iomuxc_lpsr: iomuxc-lpsr at 302c0000 { - compatible = "fsl,imx7d-iomuxc-lpsr"; - reg = <0x302c0000 0x10000>; - fsl,input-sel = <&iomuxc>; - }; - - iomuxc: iomuxc at 30330000 { - compatible = "fsl,imx7d-iomuxc"; - reg = <0x30330000 0x10000>; - }; - }; - - aips3: aips-bus at 30800000 { - compatible = "fsl,aips-bus", "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - reg = <0x30800000 0x400000>; - ranges; - - uart1: serial at 30860000 { - compatible = "fsl,imx7d-uart", - "fsl,imx6q-uart"; - reg = <0x30860000 0x10000>; - status = "disabled"; - }; - - uart2: serial at 30890000 { - compatible = "fsl,imx7d-uart", - "fsl,imx6q-uart"; - reg = <0x30890000 0x10000>; - status = "disabled"; - }; - - uart3: serial at 30880000 { - compatible = "fsl,imx7d-uart", - "fsl,imx6q-uart"; - reg = <0x30880000 0x10000>; - status = "disabled"; - }; - - i2c1: i2c at 30a20000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c"; - reg = <0x30a20000 0x10000>; - status = "disabled"; - }; - - i2c2: i2c at 30a30000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c"; - reg = <0x30a30000 0x10000>; - status = "disabled"; - }; - - i2c3: i2c at 30a40000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c"; - reg = <0x30a40000 0x10000>; - status = "disabled"; - }; - - i2c4: i2c at 30a50000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c"; - reg = <0x30a50000 0x10000>; - status = "disabled"; - }; - - uart4: serial at 30a60000 { - compatible = "fsl,imx7d-uart", - "fsl,imx6q-uart"; - reg = <0x30a60000 0x10000>; - status = "disabled"; - }; - - uart5: serial at 30a70000 { - compatible = "fsl,imx7d-uart", - "fsl,imx6q-uart"; - reg = <0x30a70000 0x10000>; - status = "disabled"; - }; - - uart6: serial at 30a80000 { - compatible = "fsl,imx7d-uart", - "fsl,imx6q-uart"; - reg = <0x30a80000 0x10000>; - status = "disabled"; - }; - - uart7: serial at 30a90000 { - compatible = "fsl,imx7d-uart", - "fsl,imx6q-uart"; - reg = <0x30a90000 0x10000>; - status = "disabled"; - }; - }; - }; -};arch/arm/dts/imx7d-pinfunc.h +59
-52@@ -1,7 +1,10 @@/* * Copyright (C) 2014-2015 Freescale Semiconductor, Inc. * -* SPDX-License-Identifier: GPL-2.0+ +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* */ #ifndef __DTS_IMX7D_PINFUNC_H@@ -12,57 +15,61 @@* <mux_reg conf_reg input_reg mux_mode input_val> */ -#define MX7D_PAD_GPIO1_IO00__GPIO1_IO0 0x0000 0x0030 0x0000 0x0 0x0 -#define MX7D_PAD_GPIO1_IO00__PWM4_OUT 0x0000 0x0030 0x0000 0x1 0x0 -#define MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_ANY 0x0000 0x0030 0x0000 0x2 0x0 -#define MX7D_PAD_GPIO1_IO00__WDOD1_WDOG_B 0x0000 0x0030 0x0000 0x3 0x0 -#define MX7D_PAD_GPIO1_IO00__WDOD1_WDOG__RST_B_DEB 0x0000 0x0030 0x0000 0x4 0x0 -#define MX7D_PAD_GPIO1_IO01__GPIO1_IO1 0x0004 0x0034 0x0000 0x0 0x0 -#define MX7D_PAD_GPIO1_IO01__PWM1_OUT 0x0004 0x0034 0x0000 0x1 0x0 -#define MX7D_PAD_GPIO1_IO01__CCM_ENET_REF_CLK3 0x0004 0x0034 0x0000 0x2 0x0 -#define MX7D_PAD_GPIO1_IO01__SAI1_MCLK 0x0004 0x0034 0x0000 0x3 0x0 -#define MX7D_PAD_GPIO1_IO01__ANATOP_24M_OUT 0x0004 0x0034 0x0000 0x4 0x0 -#define MX7D_PAD_GPIO1_IO01__OBSERVE0_OUT 0x0004 0x0034 0x0000 0x6 0x0 -#define MX7D_PAD_GPIO1_IO02__GPIO1_IO2 0x0008 0x0038 0x0000 0x0 0x0 -#define MX7D_PAD_GPIO1_IO02__PWM2_OUT 0x0008 0x0038 0x0000 0x1 0x0 -#define MX7D_PAD_GPIO1_IO02__CCM_ENET_REF_CLK1 0x0008 0x0038 0x0564 0x2 0x3 -#define MX7D_PAD_GPIO1_IO02__SAI2_MCLK 0x0008 0x0038 0x0000 0x3 0x0 -#define MX7D_PAD_GPIO1_IO02__CCM_CLKO1 0x0008 0x0038 0x0000 0x5 0x0 -#define MX7D_PAD_GPIO1_IO02__OBSERVE1_OUT 0x0008 0x0038 0x0000 0x6 0x0 -#define MX7D_PAD_GPIO1_IO02__USB_OTG1_ID 0x0008 0x0038 0x0734 0x7 0x3 -#define MX7D_PAD_GPIO1_IO03__GPIO1_IO3 0x000C 0x003C 0x0000 0x0 0x0 -#define MX7D_PAD_GPIO1_IO03__PWM3_OUT 0x000C 0x003C 0x0000 0x1 0x0 -#define MX7D_PAD_GPIO1_IO03__CCM_ENET_REF_CLK2 0x000C 0x003C 0x0570 0x2 0x3 -#define MX7D_PAD_GPIO1_IO03__SAI3_MCLK 0x000C 0x003C 0x0000 0x3 0x0 -#define MX7D_PAD_GPIO1_IO03__CCM_CLKO2 0x000C 0x003C 0x0000 0x5 0x0 -#define MX7D_PAD_GPIO1_IO03__OBSERVE2_OUT 0x000C 0x003C 0x0000 0x6 0x0 -#define MX7D_PAD_GPIO1_IO03__USB_OTG2_ID 0x000C 0x003C 0x0730 0x7 0x3 -#define MX7D_PAD_GPIO1_IO04__GPIO1_IO4 0x0010 0x0040 0x0000 0x0 0x0 -#define MX7D_PAD_GPIO1_IO04__USB_OTG1_OC 0x0010 0x0040 0x072C 0x1 0x1 -#define MX7D_PAD_GPIO1_IO04__FLEXTIMER1_CH4 0x0010 0x0040 0x0594 0x2 0x1 -#define MX7D_PAD_GPIO1_IO04__UART5_CTS_B 0x0010 0x0040 0x0710 0x3 0x4 -#define MX7D_PAD_GPIO1_IO04__I2C1_SCL 0x0010 0x0040 0x05D4 0x4 0x2 -#define MX7D_PAD_GPIO1_IO04__OBSERVE3_OUT 0x0010 0x0040 0x0000 0x6 0x0 -#define MX7D_PAD_GPIO1_IO05__GPIO1_IO5 0x0014 0x0044 0x0000 0x0 0x0 -#define MX7D_PAD_GPIO1_IO05__USB_OTG1_PWR 0x0014 0x0044 0x0000 0x1 0x0 -#define MX7D_PAD_GPIO1_IO05__FLEXTIMER1_CH5 0x0014 0x0044 0x0598 0x2 0x1 -#define MX7D_PAD_GPIO1_IO05__UART5_RTS_B 0x0014 0x0044 0x0710 0x3 0x5 -#define MX7D_PAD_GPIO1_IO05__I2C1_SDA 0x0014 0x0044 0x05D8 0x4 0x2 -#define MX7D_PAD_GPIO1_IO05__OBSERVE4_OUT 0x0014 0x0044 0x0000 0x6 0x0 -#define MX7D_PAD_GPIO1_IO06__GPIO1_IO6 0x0018 0x0048 0x0000 0x0 0x0 -#define MX7D_PAD_GPIO1_IO06__USB_OTG2_OC 0x0018 0x0048 0x0728 0x1 0x1 -#define MX7D_PAD_GPIO1_IO06__FLEXTIMER1_CH6 0x0018 0x0048 0x059C 0x2 0x1 -#define MX7D_PAD_GPIO1_IO06__UART5_RX_DATA 0x0018 0x0048 0x0714 0x3 0x4 -#define MX7D_PAD_GPIO1_IO06__I2C2_SCL 0x0018 0x0048 0x05DC 0x4 0x2 -#define MX7D_PAD_GPIO1_IO06__CCM_WAIT 0x0018 0x0048 0x0000 0x5 0x0 -#define MX7D_PAD_GPIO1_IO06__KPP_ROW4 0x0018 0x0048 0x0624 0x6 0x1 -#define MX7D_PAD_GPIO1_IO07__GPIO1_IO7 0x001C 0x004C 0x0000 0x0 0x0 -#define MX7D_PAD_GPIO1_IO07__USB_OTG2_PWR 0x001C 0x004C 0x0000 0x1 0x0 -#define MX7D_PAD_GPIO1_IO07__FLEXTIMER1_CH7 0x001C 0x004C 0x05A0 0x2 0x1 -#define MX7D_PAD_GPIO1_IO07__UART5_TX_DATA 0x001C 0x004C 0x0714 0x3 0x5 -#define MX7D_PAD_GPIO1_IO07__I2C2_SDA 0x001C 0x004C 0x05E0 0x4 0x2 -#define MX7D_PAD_GPIO1_IO07__CCM_STOP 0x001C 0x004C 0x0000 0x5 0x0 -#define MX7D_PAD_GPIO1_IO07__KPP_COL4 0x001C 0x004C 0x0604 0x6 0x1 +#define MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0 0x0000 0x0030 0x0000 0x0 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO00__PWM4_OUT 0x0000 0x0030 0x0000 0x1 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO00__WDOD1_WDOG_ANY 0x0000 0x0030 0x0000 0x2 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO00__WDOD1_WDOG_B 0x0000 0x0030 0x0000 0x3 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO00__WDOD1_WDOG__RST_B_DEB 0x0000 0x0030 0x0000 0x4 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1 0x0004 0x0034 0x0000 0x0 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO01__PWM1_OUT 0x0004 0x0034 0x0000 0x1 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO01__CCM_ENET_REF_CLK3 0x0004 0x0034 0x0000 0x2 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO01__SAI1_MCLK 0x0004 0x0034 0x0000 0x3 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO01__ANATOP_24M_OUT 0x0004 0x0034 0x0000 0x4 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO01__OBSERVE0_OUT 0x0004 0x0034 0x0000 0x6 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2 0x0008 0x0038 0x0000 0x0 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO02__PWM2_OUT 0x0008 0x0038 0x0000 0x1 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO02__CCM_ENET_REF_CLK1 0x0008 0x0038 0x0564 0x2 0x3 +#define MX7D_PAD_LPSR_GPIO1_IO02__SAI2_MCLK 0x0008 0x0038 0x0000 0x3 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO02__CCM_CLKO1 0x0008 0x0038 0x0000 0x5 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO02__OBSERVE1_OUT 0x0008 0x0038 0x0000 0x6 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO02__USB_OTG1_ID 0x0008 0x0038 0x0734 0x7 0x3 +#define MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3 0x000C 0x003C 0x0000 0x0 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO03__PWM3_OUT 0x000C 0x003C 0x0000 0x1 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO03__CCM_ENET_REF_CLK2 0x000C 0x003C 0x0570 0x2 0x3 +#define MX7D_PAD_LPSR_GPIO1_IO03__SAI3_MCLK 0x000C 0x003C 0x0000 0x3 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO03__CCM_CLKO2 0x000C 0x003C 0x0000 0x5 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO03__OBSERVE2_OUT 0x000C 0x003C 0x0000 0x6 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO03__USB_OTG2_ID 0x000C 0x003C 0x0730 0x7 0x3 +#define MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4 0x0010 0x0040 0x0000 0x0 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO04__USB_OTG1_OC 0x0010 0x0040 0x072C 0x1 0x1 +#define MX7D_PAD_LPSR_GPIO1_IO04__FLEXTIMER1_CH4 0x0010 0x0040 0x0594 0x2 0x1 +#define MX7D_PAD_LPSR_GPIO1_IO04__UART5_DCE_CTS 0x0010 0x0040 0x0000 0x3 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO04__UART5_DTE_RTS 0x0010 0x0040 0x0710 0x3 0x4 +#define MX7D_PAD_LPSR_GPIO1_IO04__I2C1_SCL 0x0010 0x0040 0x05D4 0x4 0x2 +#define MX7D_PAD_LPSR_GPIO1_IO04__OBSERVE3_OUT 0x0010 0x0040 0x0000 0x6 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5 0x0014 0x0044 0x0000 0x0 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO05__USB_OTG1_PWR 0x0014 0x0044 0x0000 0x1 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO05__FLEXTIMER1_CH5 0x0014 0x0044 0x0598 0x2 0x1 +#define MX7D_PAD_LPSR_GPIO1_IO05__UART5_DCE_RTS 0x0014 0x0044 0x0710 0x3 0x5 +#define MX7D_PAD_LPSR_GPIO1_IO05__UART5_DTE_CTS 0x0014 0x0044 0x0000 0x3 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA 0x0014 0x0044 0x05D8 0x4 0x2 +#define MX7D_PAD_LPSR_GPIO1_IO05__OBSERVE4_OUT 0x0014 0x0044 0x0000 0x6 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6 0x0018 0x0048 0x0000 0x0 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO06__USB_OTG2_OC 0x0018 0x0048 0x0728 0x1 0x1 +#define MX7D_PAD_LPSR_GPIO1_IO06__FLEXTIMER1_CH6 0x0018 0x0048 0x059C 0x2 0x1 +#define MX7D_PAD_LPSR_GPIO1_IO06__UART5_DCE_RX 0x0018 0x0048 0x0714 0x3 0x4 +#define MX7D_PAD_LPSR_GPIO1_IO06__UART5_DTE_TX 0x0018 0x0048 0x0000 0x3 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO06__I2C2_SCL 0x0018 0x0048 0x05DC 0x4 0x2 +#define MX7D_PAD_LPSR_GPIO1_IO06__CCM_WAIT 0x0018 0x0048 0x0000 0x5 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO06__KPP_ROW4 0x0018 0x0048 0x0624 0x6 0x1 +#define MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7 0x001C 0x004C 0x0000 0x0 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO07__USB_OTG2_PWR 0x001C 0x004C 0x0000 0x1 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO07__FLEXTIMER1_CH7 0x001C 0x004C 0x05A0 0x2 0x1 +#define MX7D_PAD_LPSR_GPIO1_IO07__UART5_DCE_TX 0x001C 0x004C 0x0000 0x3 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO07__UART5_DTE_RX 0x001C 0x004C 0x0714 0x3 0x5 +#define MX7D_PAD_LPSR_GPIO1_IO07__I2C2_SDA 0x001C 0x004C 0x05E0 0x4 0x2 +#define MX7D_PAD_LPSR_GPIO1_IO07__CCM_STOP 0x001C 0x004C 0x0000 0x5 0x0 +#define MX7D_PAD_LPSR_GPIO1_IO07__KPP_COL4 0x001C 0x004C 0x0604 0x6 0x1#define MX7D_PAD_GPIO1_IO08__GPIO1_IO8 0x0014 0x026C 0x0000 0x0 0x0#define MX7D_PAD_GPIO1_IO08__SD1_VSELECT 0x0014 0x026C 0x0000 0x1 0x0#define MX7D_PAD_GPIO1_IO08__WDOG1_WDOG_B 0x0014 0x026C 0x0000 0x2 0x0arch/arm/dts/imx7d.dtsi new file +140
-0@@ -0,0 +1,140 @@ +/* + * Copyright 2015 Freescale Semiconductor, Inc. + * Copyright 2016 Toradex AG + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include "imx7s.dtsi" + +/ { + cpus { + cpu0: cpu at 0 { + operating-points = < + /* KHz uV */ + 996000 1075000 + 792000 975000 + >; + clock-frequency = <996000000>; + }; + + cpu1: cpu at 1 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <1>; + clock-frequency = <996000000>; + }; + }; + + soc { + etm at 3007d000 { + compatible = "arm,coresight-etm3x", "arm,primecell"; + reg = <0x3007d000 0x1000>; + + /* + * System will hang if added nosmp in kernel command line + * without arm,primecell-periphid because amba bus try to + * read id and core1 power off at this time. + */ + arm,primecell-periphid = <0xbb956>; + cpu = <&cpu1>; + clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>; + clock-names = "apb_pclk"; + + port { + etm1_out_port: endpoint { + remote-endpoint = <&ca_funnel_in_port1>; + }; + }; + }; + }; +}; + +&aips3 { + usbotg2: usb at 30b20000 { + compatible = "fsl,imx7d-usb", "fsl,imx27-usb"; + reg = <0x30b20000 0x200>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_USB_CTRL_CLK>; + fsl,usbphy = <&usbphynop2>; + fsl,usbmisc = <&usbmisc2 0>; + phy-clkgate-delay-us = <400>; + status = "disabled"; + }; + + usbmisc2: usbmisc at 30b20200 { + #index-cells = <1>; + compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc"; + reg = <0x30b20200 0x200>; + }; + + usbphynop2: usbphynop2 { + compatible = "usb-nop-xceiv"; + clocks = <&clks IMX7D_USB_PHY2_CLK>; + clock-names = "main_clk"; + }; + + fec2: ethernet at 30bf0000 { + compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec"; + reg = <0x30bf0000 0x10000>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>, + <&clks IMX7D_ENET_AXI_ROOT_CLK>, + <&clks IMX7D_ENET2_TIME_ROOT_CLK>, + <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>, + <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>; + clock-names = "ipg", "ahb", "ptp", + "enet_clk_ref", "enet_out"; + fsl,num-tx-queues=<3>; + fsl,num-rx-queues=<3>; + status = "disabled"; + }; +}; + +&ca_funnel_ports { + port at 1 { + reg = <1>; + ca_funnel_in_port1: endpoint { + slave-mode; + remote-endpoint = <&etm1_out_port>; + }; + }; +};arch/arm/dts/imx7s.dtsi new file +999
-0@@ -0,0 +1,999 @@ +/* + * Copyright 2015 Freescale Semiconductor, Inc. + * Copyright 2016 Toradex AG + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/clock/imx7d-clock.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include "imx7d-pinfunc.h" + +/ { + #address-cells = <1>; + #size-cells = <1>; + /* + * The decompressor and also some bootloaders rely on a + * pre-existing /chosen node to be available to insert the + * command line and merge other ATAGS info. + * Also for U-Boot there must be a pre-existing /memory node. + */ + chosen {}; + memory { device_type = "memory"; reg = <0 0>; }; + + aliases { + gpio0 = &gpio1; + gpio1 = &gpio2; + gpio2 = &gpio3; + gpio3 = &gpio4; + gpio4 = &gpio5; + gpio5 = &gpio6; + gpio6 = &gpio7; + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + i2c3 = &i2c4; + mmc0 = &usdhc1; + mmc1 = &usdhc2; + mmc2 = &usdhc3; + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + serial3 = &uart4; + serial4 = &uart5; + serial5 = &uart6; + serial6 = &uart7; + spi0 = &ecspi1; + spi1 = &ecspi2; + spi2 = &ecspi3; + spi3 = &ecspi4; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu at 0 { + compatible = "arm,cortex-a7"; + device_type = "cpu"; + reg = <0>; + clock-frequency = <792000000>; + clock-latency = <61036>; /* two CLK32 periods */ + clocks = <&clks IMX7D_CLK_ARM>; + }; + }; + + ckil: clock-cki { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "ckil"; + }; + + osc: clock-osc { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "osc"; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + interrupt-parent = <&intc>; + ranges; + + funnel at 30041000 { + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0x30041000 0x1000>; + clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>; + clock-names = "apb_pclk"; + + ca_funnel_ports: ports { + #address-cells = <1>; + #size-cells = <0>; + + /* funnel input ports */ + port at 0 { + reg = <0>; + ca_funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = <&etm0_out_port>; + }; + }; + + /* funnel output port */ + port at 2 { + reg = <0>; + ca_funnel_out_port0: endpoint { + remote-endpoint = <&hugo_funnel_in_port0>; + }; + }; + + /* the other input ports are not connect to anything */ + }; + }; + + etm at 3007c000 { + compatible = "arm,coresight-etm3x", "arm,primecell"; + reg = <0x3007c000 0x1000>; + cpu = <&cpu0>; + clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>; + clock-names = "apb_pclk"; + + port { + etm0_out_port: endpoint { + remote-endpoint = <&ca_funnel_in_port0>; + }; + }; + }; + + funnel at 30083000 { + compatible = "arm,coresight-funnel", "arm,primecell"; + reg = <0x30083000 0x1000>; + clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>; + clock-names = "apb_pclk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* funnel input ports */ + port at 0 { + reg = <0>; + hugo_funnel_in_port0: endpoint { + slave-mode; + remote-endpoint = <&ca_funnel_out_port0>; + }; + }; + + port at 1 { + reg = <1>; + hugo_funnel_in_port1: endpoint { + slave-mode; /* M4 input */ + }; + }; + + port at 2 { + reg = <0>; + hugo_funnel_out_port0: endpoint { + remote-endpoint = <&etf_in_port>; + }; + }; + + /* the other input ports are not connect to anything */ + }; + }; + + etf at 30084000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0x30084000 0x1000>; + clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>; + clock-names = "apb_pclk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + reg = <0>; + etf_in_port: endpoint { + slave-mode; + remote-endpoint = <&hugo_funnel_out_port0>; + }; + }; + + port at 1 { + reg = <0>; + etf_out_port: endpoint { + remote-endpoint = <&replicator_in_port0>; + }; + }; + }; + }; + + etr at 30086000 { + compatible = "arm,coresight-tmc", "arm,primecell"; + reg = <0x30086000 0x1000>; + clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>; + clock-names = "apb_pclk"; + + port { + etr_in_port: endpoint { + slave-mode; + remote-endpoint = <&replicator_out_port1>; + }; + }; + }; + + tpiu at 30087000 { + compatible = "arm,coresight-tpiu", "arm,primecell"; + reg = <0x30087000 0x1000>; + clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>; + clock-names = "apb_pclk"; + + port { + tpiu_in_port: endpoint { + slave-mode; + remote-endpoint = <&replicator_out_port1>; + }; + }; + }; + + replicator { + /* + * non-configurable replicators don't show up on the + * AMBA bus. As such no need to add "arm,primecell" + */ + compatible = "arm,coresight-replicator"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* replicator output ports */ + port at 0 { + reg = <0>; + replicator_out_port0: endpoint { + remote-endpoint = <&tpiu_in_port>; + }; + }; + + port at 1 { + reg = <1>; + replicator_out_port1: endpoint { + remote-endpoint = <&etr_in_port>; + }; + }; + + /* replicator input port */ + port at 2 { + reg = <0>; + replicator_in_port0: endpoint { + slave-mode; + remote-endpoint = <&etf_out_port>; + }; + }; + }; + }; + + intc: interrupt-controller at 31001000 { + compatible = "arm,cortex-a7-gic"; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x31001000 0x1000>, + <0x31002000 0x2000>, + <0x31004000 0x2000>, + <0x31006000 0x2000>; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; + + aips1: aips-bus at 30000000 { + compatible = "fsl,aips-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x30000000 0x400000>; + ranges; + + gpio1: gpio at 30200000 { + compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; + reg = <0x30200000 0x10000>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, /* GPIO1_INT15_0 */ + <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; /* GPIO1_INT31_16 */ + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc_lpsr 0 0 8>, <&iomuxc 8 5 8>; + }; + + gpio2: gpio at 30210000 { + compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; + reg = <0x30210000 0x10000>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 13 32>; + }; + + gpio3: gpio at 30220000 { + compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; + reg = <0x30220000 0x10000>; + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 45 29>; + }; + + gpio4: gpio at 30230000 { + compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; + reg = <0x30230000 0x10000>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 74 24>; + }; + + gpio5: gpio at 30240000 { + compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; + reg = <0x30240000 0x10000>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 98 18>; + }; + + gpio6: gpio at 30250000 { + compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; + reg = <0x30250000 0x10000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 116 23>; + }; + + gpio7: gpio at 30260000 { + compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio"; + reg = <0x30260000 0x10000>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&iomuxc 0 139 16>; + }; + + wdog1: wdog at 30280000 { + compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt"; + reg = <0x30280000 0x10000>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_WDOG1_ROOT_CLK>; + }; + + wdog2: wdog at 30290000 { + compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt"; + reg = <0x30290000 0x10000>; + interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_WDOG2_ROOT_CLK>; + status = "disabled"; + }; + + wdog3: wdog at 302a0000 { + compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt"; + reg = <0x302a0000 0x10000>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_WDOG3_ROOT_CLK>; + status = "disabled"; + }; + + wdog4: wdog at 302b0000 { + compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt"; + reg = <0x302b0000 0x10000>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_WDOG4_ROOT_CLK>; + status = "disabled"; + }; + + iomuxc_lpsr: iomuxc-lpsr at 302c0000 { + compatible = "fsl,imx7d-iomuxc-lpsr"; + reg = <0x302c0000 0x10000>; + fsl,input-sel = <&iomuxc>; + }; + + gpt1: gpt at 302d0000 { + compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt"; + reg = <0x302d0000 0x10000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_GPT1_ROOT_CLK>; + clock-names = "ipg", "per"; + }; + + gpt2: gpt at 302e0000 { + compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt"; + reg = <0x302e0000 0x10000>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_GPT2_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + gpt3: gpt at 302f0000 { + compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt"; + reg = <0x302f0000 0x10000>; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_GPT3_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + gpt4: gpt at 30300000 { + compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt"; + reg = <0x30300000 0x10000>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_GPT4_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + iomuxc: iomuxc at 30330000 { + compatible = "fsl,imx7d-iomuxc"; + reg = <0x30330000 0x10000>; + }; + + gpr: iomuxc-gpr at 30340000 { + compatible = "fsl,imx7d-iomuxc-gpr", "syscon"; + reg = <0x30340000 0x10000>; + }; + + ocotp: ocotp-ctrl at 30350000 { + compatible = "fsl,imx7d-ocotp", "syscon"; + reg = <0x30350000 0x10000>; + clocks = <&clks IMX7D_OCOTP_CLK>; + }; + + anatop: anatop at 30360000 { + compatible = "fsl,imx7d-anatop", "fsl,imx6q-anatop", + "syscon", "simple-bus"; + reg = <0x30360000 0x10000>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + + reg_1p0d: regulator-vdd1p0d { + compatible = "fsl,anatop-regulator"; + regulator-name = "vdd1p0d"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1200000>; + anatop-reg-offset = <0x210>; + anatop-vol-bit-shift = <8>; + anatop-vol-bit-width = <5>; + anatop-min-bit-val = <8>; + anatop-min-voltage = <800000>; + anatop-max-voltage = <1200000>; + }; + }; + + snvs: snvs at 30370000 { + compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd"; + reg = <0x30370000 0x10000>; + + snvs_rtc: snvs-rtc-lp { + compatible = "fsl,sec-v4.0-mon-rtc-lp"; + regmap = <&snvs>; + offset = <0x34>; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + }; + + snvs_poweroff: snvs-poweroff { + compatible = "syscon-poweroff"; + regmap = <&snvs>; + offset = <0x38>; + mask = <0x60>; + }; + + snvs_pwrkey: snvs-powerkey { + compatible = "fsl,sec-v4.0-pwrkey"; + regmap = <&snvs>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + linux,keycode = <KEY_POWER>; + wakeup-source; + }; + }; + + clks: ccm at 30380000 { + compatible = "fsl,imx7d-ccm"; + reg = <0x30380000 0x10000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + #clock-cells = <1>; + clocks = <&ckil>, <&osc>; + clock-names = "ckil", "osc"; + }; + + src: src at 30390000 { + compatible = "fsl,imx7d-src", "fsl,imx51-src", "syscon"; + reg = <0x30390000 0x10000>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + #reset-cells = <1>; + }; + }; + + aips2: aips-bus at 30400000 { + compatible = "fsl,aips-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x30400000 0x400000>; + ranges; + + adc1: adc at 30610000 { + compatible = "fsl,imx7d-adc"; + reg = <0x30610000 0x10000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ADC_ROOT_CLK>; + clock-names = "adc"; + status = "disabled"; + }; + + adc2: adc at 30620000 { + compatible = "fsl,imx7d-adc"; + reg = <0x30620000 0x10000>; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ADC_ROOT_CLK>; + clock-names = "adc"; + status = "disabled"; + }; + + ecspi4: ecspi at 30630000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx7d-ecspi", "fsl,imx51-ecspi"; + reg = <0x30630000 0x10000>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ECSPI4_ROOT_CLK>, + <&clks IMX7D_ECSPI4_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + pwm1: pwm at 30660000 { + compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm"; + reg = <0x30660000 0x10000>; + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_PWM1_ROOT_CLK>, + <&clks IMX7D_PWM1_ROOT_CLK>; + clock-names = "ipg", "per"; + #pwm-cells = <2>; + status = "disabled"; + }; + + pwm2: pwm at 30670000 { + compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm"; + reg = <0x30670000 0x10000>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_PWM2_ROOT_CLK>, + <&clks IMX7D_PWM2_ROOT_CLK>; + clock-names = "ipg", "per"; + #pwm-cells = <2>; + status = "disabled"; + }; + + pwm3: pwm at 30680000 { + compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm"; + reg = <0x30680000 0x10000>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_PWM3_ROOT_CLK>, + <&clks IMX7D_PWM3_ROOT_CLK>; + clock-names = "ipg", "per"; + #pwm-cells = <2>; + status = "disabled"; + }; + + pwm4: pwm at 30690000 { + compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm"; + reg = <0x30690000 0x10000>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_PWM4_ROOT_CLK>, + <&clks IMX7D_PWM4_ROOT_CLK>; + clock-names = "ipg", "per"; + #pwm-cells = <2>; + status = "disabled"; + }; + + lcdif: lcdif at 30730000 { + compatible = "fsl,imx7d-lcdif", "fsl,imx28-lcdif"; + reg = <0x30730000 0x10000>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>, + <&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>; + clock-names = "pix", "axi"; + status = "disabled"; + }; + }; + + aips3: aips-bus at 30800000 { + compatible = "fsl,aips-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x30800000 0x400000>; + ranges; + + ecspi1: ecspi at 30820000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx7d-ecspi", "fsl,imx51-ecspi"; + reg = <0x30820000 0x10000>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ECSPI1_ROOT_CLK>, + <&clks IMX7D_ECSPI1_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + ecspi2: ecspi at 30830000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx7d-ecspi", "fsl,imx51-ecspi"; + reg = <0x30830000 0x10000>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ECSPI2_ROOT_CLK>, + <&clks IMX7D_ECSPI2_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + ecspi3: ecspi at 30840000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx7d-ecspi", "fsl,imx51-ecspi"; + reg = <0x30840000 0x10000>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ECSPI3_ROOT_CLK>, + <&clks IMX7D_ECSPI3_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + uart1: serial at 30860000 { + compatible = "fsl,imx7d-uart", + "fsl,imx6q-uart"; + reg = <0x30860000 0x10000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_UART1_ROOT_CLK>, + <&clks IMX7D_UART1_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + uart2: serial at 30890000 { + compatible = "fsl,imx7d-uart", + "fsl,imx6q-uart"; + reg = <0x30890000 0x10000>; + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_UART2_ROOT_CLK>, + <&clks IMX7D_UART2_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + uart3: serial at 30880000 { + compatible = "fsl,imx7d-uart", + "fsl,imx6q-uart"; + reg = <0x30880000 0x10000>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_UART3_ROOT_CLK>, + <&clks IMX7D_UART3_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + sai1: sai at 308a0000 { + #sound-dai-cells = <0>; + compatible = "fsl,imx7d-sai", "fsl,imx6sx-sai"; + reg = <0x308a0000 0x10000>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_SAI1_IPG_CLK>, + <&clks IMX7D_SAI1_ROOT_CLK>, + <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CLK_DUMMY>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "rx", "tx"; + dmas = <&sdma 8 24 0>, <&sdma 9 24 0>; + status = "disabled"; + }; + + sai2: sai at 308b0000 { + #sound-dai-cells = <0>; + compatible = "fsl,imx7d-sai", "fsl,imx6sx-sai"; + reg = <0x308b0000 0x10000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_SAI2_IPG_CLK>, + <&clks IMX7D_SAI2_ROOT_CLK>, + <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CLK_DUMMY>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "rx", "tx"; + dmas = <&sdma 10 24 0>, <&sdma 11 24 0>; + status = "disabled"; + }; + + sai3: sai at 308c0000 { + #sound-dai-cells = <0>; + compatible = "fsl,imx7d-sai", "fsl,imx6sx-sai"; + reg = <0x308c0000 0x10000>; + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_SAI3_IPG_CLK>, + <&clks IMX7D_SAI3_ROOT_CLK>, + <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CLK_DUMMY>; + clock-names = "bus", "mclk1", "mclk2", "mclk3"; + dma-names = "rx", "tx"; + dmas = <&sdma 12 24 0>, <&sdma 13 24 0>; + status = "disabled"; + }; + + flexcan1: can at 30a00000 { + compatible = "fsl,imx7d-flexcan", "fsl,imx6q-flexcan"; + reg = <0x30a00000 0x10000>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CAN1_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + flexcan2: can at 30a10000 { + compatible = "fsl,imx7d-flexcan", "fsl,imx6q-flexcan"; + reg = <0x30a10000 0x10000>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CAN2_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + i2c1: i2c at 30a20000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c"; + reg = <0x30a20000 0x10000>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_I2C1_ROOT_CLK>; + status = "disabled"; + }; + + i2c2: i2c at 30a30000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c"; + reg = <0x30a30000 0x10000>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_I2C2_ROOT_CLK>; + status = "disabled"; + }; + + i2c3: i2c at 30a40000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c"; + reg = <0x30a40000 0x10000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_I2C3_ROOT_CLK>; + status = "disabled"; + }; + + i2c4: i2c at 30a50000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c"; + reg = <0x30a50000 0x10000>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_I2C4_ROOT_CLK>; + status = "disabled"; + }; + + uart4: serial at 30a60000 { + compatible = "fsl,imx7d-uart", + "fsl,imx6q-uart"; + reg = <0x30a60000 0x10000>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_UART4_ROOT_CLK>, + <&clks IMX7D_UART4_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + uart5: serial at 30a70000 { + compatible = "fsl,imx7d-uart", + "fsl,imx6q-uart"; + reg = <0x30a70000 0x10000>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_UART5_ROOT_CLK>, + <&clks IMX7D_UART5_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + uart6: serial at 30a80000 { + compatible = "fsl,imx7d-uart", + "fsl,imx6q-uart"; + reg = <0x30a80000 0x10000>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_UART6_ROOT_CLK>, + <&clks IMX7D_UART6_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + uart7: serial at 30a90000 { + compatible = "fsl,imx7d-uart", + "fsl,imx6q-uart"; + reg = <0x30a90000 0x10000>; + interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_UART7_ROOT_CLK>, + <&clks IMX7D_UART7_ROOT_CLK>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + usbotg1: usb at 30b10000 { + compatible = "fsl,imx7d-usb", "fsl,imx27-usb"; + reg = <0x30b10000 0x200>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_USB_CTRL_CLK>; + fsl,usbphy = <&usbphynop1>; + fsl,usbmisc = <&usbmisc1 0>; + phy-clkgate-delay-us = <400>; + status = "disabled"; + }; + + usbh: usb at 30b30000 { + compatible = "fsl,imx7d-usb", "fsl,imx27-usb"; + reg = <0x30b30000 0x200>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_USB_CTRL_CLK>; + fsl,usbphy = <&usbphynop3>; + fsl,usbmisc = <&usbmisc3 0>; + phy_type = "hsic"; + dr_mode = "host"; + phy-clkgate-delay-us = <400>; + status = "disabled"; + }; + + usbmisc1: usbmisc at 30b10200 { + #index-cells = <1>; + compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc"; + reg = <0x30b10200 0x200>; + }; + + usbmisc3: usbmisc at 30b30200 { + #index-cells = <1>; + compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc"; + reg = <0x30b30200 0x200>; + }; + + usbphynop1: usbphynop1 { + compatible = "usb-nop-xceiv"; + clocks = <&clks IMX7D_USB_PHY1_CLK>; + clock-names = "main_clk"; + }; + + usbphynop3: usbphynop3 { + compatible = "usb-nop-xceiv"; + clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>; + clock-names = "main_clk"; + }; + + usdhc1: usdhc at 30b40000 { + compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc"; + reg = <0x30b40000 0x10000>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_USDHC1_ROOT_CLK>; + clock-names = "ipg", "ahb", "per"; + bus-width = <4>; + status = "disabled"; + }; + + usdhc2: usdhc at 30b50000 { + compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc"; + reg = <0x30b50000 0x10000>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_USDHC2_ROOT_CLK>; + clock-names = "ipg", "ahb", "per"; + bus-width = <4>; + status = "disabled"; + }; + + usdhc3: usdhc at 30b60000 { + compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc"; + reg = <0x30b60000 0x10000>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_USDHC3_ROOT_CLK>; + clock-names = "ipg", "ahb", "per"; + bus-width = <4>; + status = "disabled"; + }; + + sdma: sdma at 30bd0000 { + compatible = "fsl,imx7d-sdma", "fsl,imx35-sdma"; + reg = <0x30bd0000 0x10000>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_SDMA_CORE_CLK>, + <&clks IMX7D_AHB_CHANNEL_ROOT_CLK>; + clock-names = "ipg", "ahb"; + #dma-cells = <3>; + fsl,sdma-ram-script-name = "imx/sdma/sdma-imx7d.bin"; + }; + + fec1: ethernet at 30be0000 { + compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec"; + reg = <0x30be0000 0x10000>; + interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>, + <&clks IMX7D_ENET_AXI_ROOT_CLK>, + <&clks IMX7D_ENET1_TIME_ROOT_CLK>, + <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>, + <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>; + clock-names = "ipg", "ahb", "ptp", + "enet_clk_ref", "enet_out"; + fsl,num-tx-queues=<3>; + fsl,num-rx-queues=<3>; + status = "disabled"; + }; + }; + }; +};include/dt-bindings/clock/imx7d-clock.h new file +454
-0@@ -0,0 +1,454 @@ +/* +* Copyright (C) 2014-2015 Freescale Semiconductor, Inc. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* +*/ + +#ifndef __DT_BINDINGS_CLOCK_IMX7D_H +#define __DT_BINDINGS_CLOCK_IMX7D_H + +#define IMX7D_OSC_24M_CLK 0 +#define IMX7D_PLL_ARM_MAIN 1 +#define IMX7D_PLL_ARM_MAIN_CLK 2 +#define IMX7D_PLL_ARM_MAIN_SRC 3 +#define IMX7D_PLL_ARM_MAIN_BYPASS 4 +#define IMX7D_PLL_SYS_MAIN 5 +#define IMX7D_PLL_SYS_MAIN_CLK 6 +#define IMX7D_PLL_SYS_MAIN_SRC 7 +#define IMX7D_PLL_SYS_MAIN_BYPASS 8 +#define IMX7D_PLL_SYS_MAIN_480M 9 +#define IMX7D_PLL_SYS_MAIN_240M 10 +#define IMX7D_PLL_SYS_MAIN_120M 11 +#define IMX7D_PLL_SYS_MAIN_480M_CLK 12 +#define IMX7D_PLL_SYS_MAIN_240M_CLK 13 +#define IMX7D_PLL_SYS_MAIN_120M_CLK 14 +#define IMX7D_PLL_SYS_PFD0_392M_CLK 15 +#define IMX7D_PLL_SYS_PFD0_196M 16 +#define IMX7D_PLL_SYS_PFD0_196M_CLK 17 +#define IMX7D_PLL_SYS_PFD1_332M_CLK 18 +#define IMX7D_PLL_SYS_PFD1_166M 19 +#define IMX7D_PLL_SYS_PFD1_166M_CLK 20 +#define IMX7D_PLL_SYS_PFD2_270M_CLK 21 +#define IMX7D_PLL_SYS_PFD2_135M 22 +#define IMX7D_PLL_SYS_PFD2_135M_CLK 23 +#define IMX7D_PLL_SYS_PFD3_CLK 24 +#define IMX7D_PLL_SYS_PFD4_CLK 25 +#define IMX7D_PLL_SYS_PFD5_CLK 26 +#define IMX7D_PLL_SYS_PFD6_CLK 27 +#define IMX7D_PLL_SYS_PFD7_CLK 28 +#define IMX7D_PLL_ENET_MAIN 29 +#define IMX7D_PLL_ENET_MAIN_CLK 30 +#define IMX7D_PLL_ENET_MAIN_SRC 31 +#define IMX7D_PLL_ENET_MAIN_BYPASS 32 +#define IMX7D_PLL_ENET_MAIN_500M 33 +#define IMX7D_PLL_ENET_MAIN_250M 34 +#define IMX7D_PLL_ENET_MAIN_125M 35 +#define IMX7D_PLL_ENET_MAIN_100M 36 +#define IMX7D_PLL_ENET_MAIN_50M 37 +#define IMX7D_PLL_ENET_MAIN_40M 38 +#define IMX7D_PLL_ENET_MAIN_25M 39 +#define IMX7D_PLL_ENET_MAIN_500M_CLK 40 +#define IMX7D_PLL_ENET_MAIN_250M_CLK 41 +#define IMX7D_PLL_ENET_MAIN_125M_CLK 42 +#define IMX7D_PLL_ENET_MAIN_100M_CLK 43 +#define IMX7D_PLL_ENET_MAIN_50M_CLK 44 +#define IMX7D_PLL_ENET_MAIN_40M_CLK 45 +#define IMX7D_PLL_ENET_MAIN_25M_CLK 46 +#define IMX7D_PLL_DRAM_MAIN 47 +#define IMX7D_PLL_DRAM_MAIN_CLK 48 +#define IMX7D_PLL_DRAM_MAIN_SRC 49 +#define IMX7D_PLL_DRAM_MAIN_BYPASS 50 +#define IMX7D_PLL_DRAM_MAIN_533M 51 +#define IMX7D_PLL_DRAM_MAIN_533M_CLK 52 +#define IMX7D_PLL_AUDIO_MAIN 53 +#define IMX7D_PLL_AUDIO_MAIN_CLK 54 +#define IMX7D_PLL_AUDIO_MAIN_SRC 55 +#define IMX7D_PLL_AUDIO_MAIN_BYPASS 56 +#define IMX7D_PLL_VIDEO_MAIN_CLK 57 +#define IMX7D_PLL_VIDEO_MAIN 58 +#define IMX7D_PLL_VIDEO_MAIN_SRC 59 +#define IMX7D_PLL_VIDEO_MAIN_BYPASS 60 +#define IMX7D_USB_MAIN_480M_CLK 61 +#define IMX7D_ARM_A7_ROOT_CLK 62 +#define IMX7D_ARM_A7_ROOT_SRC 63 +#define IMX7D_ARM_A7_ROOT_CG 64 +#define IMX7D_ARM_A7_ROOT_DIV 65 +#define IMX7D_ARM_M4_ROOT_CLK 66 +#define IMX7D_ARM_M4_ROOT_SRC 67 +#define IMX7D_ARM_M4_ROOT_CG 68 +#define IMX7D_ARM_M4_ROOT_DIV 69 +#define IMX7D_ARM_M0_ROOT_CLK 70 +#define IMX7D_ARM_M0_ROOT_SRC 71 +#define IMX7D_ARM_M0_ROOT_CG 72 +#define IMX7D_ARM_M0_ROOT_DIV 73 +#define IMX7D_MAIN_AXI_ROOT_CLK 74 +#define IMX7D_MAIN_AXI_ROOT_SRC 75 +#define IMX7D_MAIN_AXI_ROOT_CG 76 +#define IMX7D_MAIN_AXI_ROOT_DIV 77 +#define IMX7D_DISP_AXI_ROOT_CLK 78 +#define IMX7D_DISP_AXI_ROOT_SRC 79 +#define IMX7D_DISP_AXI_ROOT_CG 80 +#define IMX7D_DISP_AXI_ROOT_DIV 81 +#define IMX7D_ENET_AXI_ROOT_CLK 82 +#define IMX7D_ENET_AXI_ROOT_SRC 83 +#define IMX7D_ENET_AXI_ROOT_CG 84 +#define IMX7D_ENET_AXI_ROOT_DIV 85 +#define IMX7D_NAND_USDHC_BUS_ROOT_CLK 86 +#define IMX7D_NAND_USDHC_BUS_ROOT_SRC 87 +#define IMX7D_NAND_USDHC_BUS_ROOT_CG 88 +#define IMX7D_NAND_USDHC_BUS_ROOT_DIV 89 +#define IMX7D_AHB_CHANNEL_ROOT_CLK 90 +#define IMX7D_AHB_CHANNEL_ROOT_SRC 91 +#define IMX7D_AHB_CHANNEL_ROOT_CG 92 +#define IMX7D_AHB_CHANNEL_ROOT_DIV 93 +#define IMX7D_DRAM_PHYM_ROOT_CLK 94 +#define IMX7D_DRAM_PHYM_ROOT_SRC 95 +#define IMX7D_DRAM_PHYM_ROOT_CG 96 +#define IMX7D_DRAM_PHYM_ROOT_DIV 97 +#define IMX7D_DRAM_ROOT_CLK 98 +#define IMX7D_DRAM_ROOT_SRC 99 +#define IMX7D_DRAM_ROOT_CG 100 +#define IMX7D_DRAM_ROOT_DIV 101 +#define IMX7D_DRAM_PHYM_ALT_ROOT_CLK 102 +#define IMX7D_DRAM_PHYM_ALT_ROOT_SRC 103 +#define IMX7D_DRAM_PHYM_ALT_ROOT_CG 104 +#define IMX7D_DRAM_PHYM_ALT_ROOT_DIV 105 +#define IMX7D_DRAM_ALT_ROOT_CLK 106 +#define IMX7D_DRAM_ALT_ROOT_SRC 107 +#define IMX7D_DRAM_ALT_ROOT_CG 108 +#define IMX7D_DRAM_ALT_ROOT_DIV 109 +#define IMX7D_USB_HSIC_ROOT_CLK 110 +#define IMX7D_USB_HSIC_ROOT_SRC 111 +#define IMX7D_USB_HSIC_ROOT_CG 112 +#define IMX7D_USB_HSIC_ROOT_DIV 113 +#define IMX7D_PCIE_CTRL_ROOT_CLK 114 +#define IMX7D_PCIE_CTRL_ROOT_SRC 115 +#define IMX7D_PCIE_CTRL_ROOT_CG 116 +#define IMX7D_PCIE_CTRL_ROOT_DIV 117 +#define IMX7D_PCIE_PHY_ROOT_CLK 118 +#define IMX7D_PCIE_PHY_ROOT_SRC 119 +#define IMX7D_PCIE_PHY_ROOT_CG 120 +#define IMX7D_PCIE_PHY_ROOT_DIV 121 +#define IMX7D_EPDC_PIXEL_ROOT_CLK 122 +#define IMX7D_EPDC_PIXEL_ROOT_SRC 123 +#define IMX7D_EPDC_PIXEL_ROOT_CG 124 +#define IMX7D_EPDC_PIXEL_ROOT_DIV 125 +#define IMX7D_LCDIF_PIXEL_ROOT_CLK 126 +#define IMX7D_LCDIF_PIXEL_ROOT_SRC 127 +#define IMX7D_LCDIF_PIXEL_ROOT_CG 128 +#define IMX7D_LCDIF_PIXEL_ROOT_DIV 129 +#define IMX7D_MIPI_DSI_ROOT_CLK 130 +#define IMX7D_MIPI_DSI_ROOT_SRC 131 +#define IMX7D_MIPI_DSI_ROOT_CG 132 +#define IMX7D_MIPI_DSI_ROOT_DIV 133 +#define IMX7D_MIPI_CSI_ROOT_CLK 134 +#define IMX7D_MIPI_CSI_ROOT_SRC 135 +#define IMX7D_MIPI_CSI_ROOT_CG 136 +#define IMX7D_MIPI_CSI_ROOT_DIV 137 +#define IMX7D_MIPI_DPHY_ROOT_CLK 138 +#define IMX7D_MIPI_DPHY_ROOT_SRC 139 +#define IMX7D_MIPI_DPHY_ROOT_CG 140 +#define IMX7D_MIPI_DPHY_ROOT_DIV 141 +#define IMX7D_SAI1_ROOT_CLK 142 +#define IMX7D_SAI1_ROOT_SRC 143 +#define IMX7D_SAI1_ROOT_CG 144 +#define IMX7D_SAI1_ROOT_DIV 145 +#define IMX7D_SAI2_ROOT_CLK 146 +#define IMX7D_SAI2_ROOT_SRC 147 +#define IMX7D_SAI2_ROOT_CG 148 +#define IMX7D_SAI2_ROOT_DIV 149 +#define IMX7D_SAI3_ROOT_CLK 150 +#define IMX7D_SAI3_ROOT_SRC 151 +#define IMX7D_SAI3_ROOT_CG 152 +#define IMX7D_SAI3_ROOT_DIV 153 +#define IMX7D_SPDIF_ROOT_CLK 154 +#define IMX7D_SPDIF_ROOT_SRC 155 +#define IMX7D_SPDIF_ROOT_CG 156 +#define IMX7D_SPDIF_ROOT_DIV 157 +#define IMX7D_ENET1_REF_ROOT_CLK 158 +#define IMX7D_ENET1_REF_ROOT_SRC 159 +#define IMX7D_ENET1_REF_ROOT_CG 160 +#define IMX7D_ENET1_REF_ROOT_DIV 161 +#define IMX7D_ENET1_TIME_ROOT_CLK 162 +#define IMX7D_ENET1_TIME_ROOT_SRC 163 +#define IMX7D_ENET1_TIME_ROOT_CG 164 +#define IMX7D_ENET1_TIME_ROOT_DIV 165 +#define IMX7D_ENET2_REF_ROOT_CLK 166 +#define IMX7D_ENET2_REF_ROOT_SRC 167 +#define IMX7D_ENET2_REF_ROOT_CG 168 +#define IMX7D_ENET2_REF_ROOT_DIV 169 +#define IMX7D_ENET2_TIME_ROOT_CLK 170 +#define IMX7D_ENET2_TIME_ROOT_SRC 171 +#define IMX7D_ENET2_TIME_ROOT_CG 172 +#define IMX7D_ENET2_TIME_ROOT_DIV 173 +#define IMX7D_ENET_PHY_REF_ROOT_CLK 174 +#define IMX7D_ENET_PHY_REF_ROOT_SRC 175 +#define IMX7D_ENET_PHY_REF_ROOT_CG 176 +#define IMX7D_ENET_PHY_REF_ROOT_DIV 177 +#define IMX7D_EIM_ROOT_CLK 178 +#define IMX7D_EIM_ROOT_SRC 179 +#define IMX7D_EIM_ROOT_CG 180 +#define IMX7D_EIM_ROOT_DIV 181 +#define IMX7D_NAND_ROOT_CLK 182 +#define IMX7D_NAND_ROOT_SRC 183 +#define IMX7D_NAND_ROOT_CG 184 +#define IMX7D_NAND_ROOT_DIV 185 +#define IMX7D_QSPI_ROOT_CLK 186 +#define IMX7D_QSPI_ROOT_SRC 187 +#define IMX7D_QSPI_ROOT_CG 188 +#define IMX7D_QSPI_ROOT_DIV 189 +#define IMX7D_USDHC1_ROOT_CLK 190 +#define IMX7D_USDHC1_ROOT_SRC 191 +#define IMX7D_USDHC1_ROOT_CG 192 +#define IMX7D_USDHC1_ROOT_DIV 193 +#define IMX7D_USDHC2_ROOT_CLK 194 +#define IMX7D_USDHC2_ROOT_SRC 195 +#define IMX7D_USDHC2_ROOT_CG 196 +#define IMX7D_USDHC2_ROOT_DIV 197 +#define IMX7D_USDHC3_ROOT_CLK 198 +#define IMX7D_USDHC3_ROOT_SRC 199 +#define IMX7D_USDHC3_ROOT_CG 200 +#define IMX7D_USDHC3_ROOT_DIV 201 +#define IMX7D_CAN1_ROOT_CLK 202 +#define IMX7D_CAN1_ROOT_SRC 203 +#define IMX7D_CAN1_ROOT_CG 204 +#define IMX7D_CAN1_ROOT_DIV 205 +#define IMX7D_CAN2_ROOT_CLK 206 +#define IMX7D_CAN2_ROOT_SRC 207 +#define IMX7D_CAN2_ROOT_CG 208 +#define IMX7D_CAN2_ROOT_DIV 209 +#define IMX7D_I2C1_ROOT_CLK 210 +#define IMX7D_I2C1_ROOT_SRC 211 +#define IMX7D_I2C1_ROOT_CG 212 +#define IMX7D_I2C1_ROOT_DIV 213 +#define IMX7D_I2C2_ROOT_CLK 214 +#define IMX7D_I2C2_ROOT_SRC 215 +#define IMX7D_I2C2_ROOT_CG 216 +#define IMX7D_I2C2_ROOT_DIV 217 +#define IMX7D_I2C3_ROOT_CLK 218 +#define IMX7D_I2C3_ROOT_SRC 219 +#define IMX7D_I2C3_ROOT_CG 220 +#define IMX7D_I2C3_ROOT_DIV 221 +#define IMX7D_I2C4_ROOT_CLK 222 +#define IMX7D_I2C4_ROOT_SRC 223 +#define IMX7D_I2C4_ROOT_CG 224 +#define IMX7D_I2C4_ROOT_DIV 225 +#define IMX7D_UART1_ROOT_CLK 226 +#define IMX7D_UART1_ROOT_SRC 227 +#define IMX7D_UART1_ROOT_CG 228 +#define IMX7D_UART1_ROOT_DIV 229 +#define IMX7D_UART2_ROOT_CLK 230 +#define IMX7D_UART2_ROOT_SRC 231 +#define IMX7D_UART2_ROOT_CG 232 +#define IMX7D_UART2_ROOT_DIV 233 +#define IMX7D_UART3_ROOT_CLK 234 +#define IMX7D_UART3_ROOT_SRC 235 +#define IMX7D_UART3_ROOT_CG 236 +#define IMX7D_UART3_ROOT_DIV 237 +#define IMX7D_UART4_ROOT_CLK 238 +#define IMX7D_UART4_ROOT_SRC 239 +#define IMX7D_UART4_ROOT_CG 240 +#define IMX7D_UART4_ROOT_DIV 241 +#define IMX7D_UART5_ROOT_CLK 242 +#define IMX7D_UART5_ROOT_SRC 243 +#define IMX7D_UART5_ROOT_CG 244 +#define IMX7D_UART5_ROOT_DIV 245 +#define IMX7D_UART6_ROOT_CLK 246 +#define IMX7D_UART6_ROOT_SRC 247 +#define IMX7D_UART6_ROOT_CG 248 +#define IMX7D_UART6_ROOT_DIV 249 +#define IMX7D_UART7_ROOT_CLK 250 +#define IMX7D_UART7_ROOT_SRC 251 +#define IMX7D_UART7_ROOT_CG 252 +#define IMX7D_UART7_ROOT_DIV 253 +#define IMX7D_ECSPI1_ROOT_CLK 254 +#define IMX7D_ECSPI1_ROOT_SRC 255 +#define IMX7D_ECSPI1_ROOT_CG 256 +#define IMX7D_ECSPI1_ROOT_DIV 257 +#define IMX7D_ECSPI2_ROOT_CLK 258 +#define IMX7D_ECSPI2_ROOT_SRC 259 +#define IMX7D_ECSPI2_ROOT_CG 260 +#define IMX7D_ECSPI2_ROOT_DIV 261 +#define IMX7D_ECSPI3_ROOT_CLK 262 +#define IMX7D_ECSPI3_ROOT_SRC 263 +#define IMX7D_ECSPI3_ROOT_CG 264 +#define IMX7D_ECSPI3_ROOT_DIV 265 +#define IMX7D_ECSPI4_ROOT_CLK 266 +#define IMX7D_ECSPI4_ROOT_SRC 267 +#define IMX7D_ECSPI4_ROOT_CG 268 +#define IMX7D_ECSPI4_ROOT_DIV 269 +#define IMX7D_PWM1_ROOT_CLK 270 +#define IMX7D_PWM1_ROOT_SRC 271 +#define IMX7D_PWM1_ROOT_CG 272 +#define IMX7D_PWM1_ROOT_DIV 273 +#define IMX7D_PWM2_ROOT_CLK 274 +#define IMX7D_PWM2_ROOT_SRC 275 +#define IMX7D_PWM2_ROOT_CG 276 +#define IMX7D_PWM2_ROOT_DIV 277 +#define IMX7D_PWM3_ROOT_CLK 278 +#define IMX7D_PWM3_ROOT_SRC 279 +#define IMX7D_PWM3_ROOT_CG 280 +#define IMX7D_PWM3_ROOT_DIV 281 +#define IMX7D_PWM4_ROOT_CLK 282 +#define IMX7D_PWM4_ROOT_SRC 283 +#define IMX7D_PWM4_ROOT_CG 284 +#define IMX7D_PWM4_ROOT_DIV 285 +#define IMX7D_FLEXTIMER1_ROOT_CLK 286 +#define IMX7D_FLEXTIMER1_ROOT_SRC 287 +#define IMX7D_FLEXTIMER1_ROOT_CG 288 +#define IMX7D_FLEXTIMER1_ROOT_DIV 289 +#define IMX7D_FLEXTIMER2_ROOT_CLK 290 +#define IMX7D_FLEXTIMER2_ROOT_SRC 291 +#define IMX7D_FLEXTIMER2_ROOT_CG 292 +#define IMX7D_FLEXTIMER2_ROOT_DIV 293 +#define IMX7D_SIM1_ROOT_CLK 294 +#define IMX7D_SIM1_ROOT_SRC 295 +#define IMX7D_SIM1_ROOT_CG 296 +#define IMX7D_SIM1_ROOT_DIV 297 +#define IMX7D_SIM2_ROOT_CLK 298 +#define IMX7D_SIM2_ROOT_SRC 299 +#define IMX7D_SIM2_ROOT_CG 300 +#define IMX7D_SIM2_ROOT_DIV 301 +#define IMX7D_GPT1_ROOT_CLK 302 +#define IMX7D_GPT1_ROOT_SRC 303 +#define IMX7D_GPT1_ROOT_CG 304 +#define IMX7D_GPT1_ROOT_DIV 305 +#define IMX7D_GPT2_ROOT_CLK 306 +#define IMX7D_GPT2_ROOT_SRC 307 +#define IMX7D_GPT2_ROOT_CG 308 +#define IMX7D_GPT2_ROOT_DIV 309 +#define IMX7D_GPT3_ROOT_CLK 310 +#define IMX7D_GPT3_ROOT_SRC 311 +#define IMX7D_GPT3_ROOT_CG 312 +#define IMX7D_GPT3_ROOT_DIV 313 +#define IMX7D_GPT4_ROOT_CLK 314 +#define IMX7D_GPT4_ROOT_SRC 315 +#define IMX7D_GPT4_ROOT_CG 316 +#define IMX7D_GPT4_ROOT_DIV 317 +#define IMX7D_TRACE_ROOT_CLK 318 +#define IMX7D_TRACE_ROOT_SRC 319 +#define IMX7D_TRACE_ROOT_CG 320 +#define IMX7D_TRACE_ROOT_DIV 321 +#define IMX7D_WDOG1_ROOT_CLK 322 +#define IMX7D_WDOG_ROOT_SRC 323 +#define IMX7D_WDOG_ROOT_CG 324 +#define IMX7D_WDOG_ROOT_DIV 325 +#define IMX7D_CSI_MCLK_ROOT_CLK 326 +#define IMX7D_CSI_MCLK_ROOT_SRC 327 +#define IMX7D_CSI_MCLK_ROOT_CG 328 +#define IMX7D_CSI_MCLK_ROOT_DIV 329 +#define IMX7D_AUDIO_MCLK_ROOT_CLK 330 +#define IMX7D_AUDIO_MCLK_ROOT_SRC 331 +#define IMX7D_AUDIO_MCLK_ROOT_CG 332 +#define IMX7D_AUDIO_MCLK_ROOT_DIV 333 +#define IMX7D_WRCLK_ROOT_CLK 334 +#define IMX7D_WRCLK_ROOT_SRC 335 +#define IMX7D_WRCLK_ROOT_CG 336 +#define IMX7D_WRCLK_ROOT_DIV 337 +#define IMX7D_CLKO1_ROOT_SRC 338 +#define IMX7D_CLKO1_ROOT_CG 339 +#define IMX7D_CLKO1_ROOT_DIV 340 +#define IMX7D_CLKO2_ROOT_SRC 341 +#define IMX7D_CLKO2_ROOT_CG 342 +#define IMX7D_CLKO2_ROOT_DIV 343 +#define IMX7D_MAIN_AXI_ROOT_PRE_DIV 344 +#define IMX7D_DISP_AXI_ROOT_PRE_DIV 345 +#define IMX7D_ENET_AXI_ROOT_PRE_DIV 346 +#define IMX7D_NAND_USDHC_BUS_ROOT_PRE_DIV 347 +#define IMX7D_AHB_CHANNEL_ROOT_PRE_DIV 348 +#define IMX7D_USB_HSIC_ROOT_PRE_DIV 349 +#define IMX7D_PCIE_CTRL_ROOT_PRE_DIV 350 +#define IMX7D_PCIE_PHY_ROOT_PRE_DIV 351 +#define IMX7D_EPDC_PIXEL_ROOT_PRE_DIV 352 +#define IMX7D_LCDIF_PIXEL_ROOT_PRE_DIV 353 +#define IMX7D_MIPI_DSI_ROOT_PRE_DIV 354 +#define IMX7D_MIPI_CSI_ROOT_PRE_DIV 355 +#define IMX7D_MIPI_DPHY_ROOT_PRE_DIV 356 +#define IMX7D_SAI1_ROOT_PRE_DIV 357 +#define IMX7D_SAI2_ROOT_PRE_DIV 358 +#define IMX7D_SAI3_ROOT_PRE_DIV 359 +#define IMX7D_SPDIF_ROOT_PRE_DIV 360 +#define IMX7D_ENET1_REF_ROOT_PRE_DIV 361 +#define IMX7D_ENET1_TIME_ROOT_PRE_DIV 362 +#define IMX7D_ENET2_REF_ROOT_PRE_DIV 363 +#define IMX7D_ENET2_TIME_ROOT_PRE_DIV 364 +#define IMX7D_ENET_PHY_REF_ROOT_PRE_DIV 365 +#define IMX7D_EIM_ROOT_PRE_DIV 366 +#define IMX7D_NAND_ROOT_PRE_DIV 367 +#define IMX7D_QSPI_ROOT_PRE_DIV 368 +#define IMX7D_USDHC1_ROOT_PRE_DIV 369 +#define IMX7D_USDHC2_ROOT_PRE_DIV 370 +#define IMX7D_USDHC3_ROOT_PRE_DIV 371 +#define IMX7D_CAN1_ROOT_PRE_DIV 372 +#define IMX7D_CAN2_ROOT_PRE_DIV 373 +#define IMX7D_I2C1_ROOT_PRE_DIV 374 +#define IMX7D_I2C2_ROOT_PRE_DIV 375 +#define IMX7D_I2C3_ROOT_PRE_DIV 376 +#define IMX7D_I2C4_ROOT_PRE_DIV 377 +#define IMX7D_UART1_ROOT_PRE_DIV 378 +#define IMX7D_UART2_ROOT_PRE_DIV 379 +#define IMX7D_UART3_ROOT_PRE_DIV 380 +#define IMX7D_UART4_ROOT_PRE_DIV 381 +#define IMX7D_UART5_ROOT_PRE_DIV 382 +#define IMX7D_UART6_ROOT_PRE_DIV 383 +#define IMX7D_UART7_ROOT_PRE_DIV 384 +#define IMX7D_ECSPI1_ROOT_PRE_DIV 385 +#define IMX7D_ECSPI2_ROOT_PRE_DIV 386 +#define IMX7D_ECSPI3_ROOT_PRE_DIV 387 +#define IMX7D_ECSPI4_ROOT_PRE_DIV 388 +#define IMX7D_PWM1_ROOT_PRE_DIV 389 +#define IMX7D_PWM2_ROOT_PRE_DIV 390 +#define IMX7D_PWM3_ROOT_PRE_DIV 391 +#define IMX7D_PWM4_ROOT_PRE_DIV 392 +#define IMX7D_FLEXTIMER1_ROOT_PRE_DIV 393 +#define IMX7D_FLEXTIMER2_ROOT_PRE_DIV 394 +#define IMX7D_SIM1_ROOT_PRE_DIV 395 +#define IMX7D_SIM2_ROOT_PRE_DIV 396 +#define IMX7D_GPT1_ROOT_PRE_DIV 397 +#define IMX7D_GPT2_ROOT_PRE_DIV 398 +#define IMX7D_GPT3_ROOT_PRE_DIV 399 +#define IMX7D_GPT4_ROOT_PRE_DIV 400 +#define IMX7D_TRACE_ROOT_PRE_DIV 401 +#define IMX7D_WDOG_ROOT_PRE_DIV 402 +#define IMX7D_CSI_MCLK_ROOT_PRE_DIV 403 +#define IMX7D_AUDIO_MCLK_ROOT_PRE_DIV 404 +#define IMX7D_WRCLK_ROOT_PRE_DIV 405 +#define IMX7D_CLKO1_ROOT_PRE_DIV 406 +#define IMX7D_CLKO2_ROOT_PRE_DIV 407 +#define IMX7D_DRAM_PHYM_ALT_ROOT_PRE_DIV 408 +#define IMX7D_DRAM_ALT_ROOT_PRE_DIV 409 +#define IMX7D_LVDS1_IN_CLK 410 +#define IMX7D_LVDS1_OUT_SEL 411 +#define IMX7D_LVDS1_OUT_CLK 412 +#define IMX7D_CLK_DUMMY 413 +#define IMX7D_GPT_3M_CLK 414 +#define IMX7D_OCRAM_CLK 415 +#define IMX7D_OCRAM_S_CLK 416 +#define IMX7D_WDOG2_ROOT_CLK 417 +#define IMX7D_WDOG3_ROOT_CLK 418 +#define IMX7D_WDOG4_ROOT_CLK 419 +#define IMX7D_SDMA_CORE_CLK 420 +#define IMX7D_USB1_MAIN_480M_CLK 421 +#define IMX7D_USB_CTRL_CLK 422 +#define IMX7D_USB_PHY1_CLK 423 +#define IMX7D_USB_PHY2_CLK 424 +#define IMX7D_IPG_ROOT_CLK 425 +#define IMX7D_SAI1_IPG_CLK 426 +#define IMX7D_SAI2_IPG_CLK 427 +#define IMX7D_SAI3_IPG_CLK 428 +#define IMX7D_PLL_AUDIO_TEST_DIV 429 +#define IMX7D_PLL_AUDIO_POST_DIV 430 +#define IMX7D_PLL_VIDEO_TEST_DIV 431 +#define IMX7D_PLL_VIDEO_POST_DIV 432 +#define IMX7D_MU_ROOT_CLK 433 +#define IMX7D_SEMA4_HS_ROOT_CLK 434 +#define IMX7D_PLL_DRAM_TEST_DIV 435 +#define IMX7D_ADC_ROOT_CLK 436 +#define IMX7D_CLK_ARM 437 +#define IMX7D_CKIL 438 +#define IMX7D_OCOTP_CLK 439 +#define IMX7D_CLK_END 440 +#endif /* __DT_BINDINGS_CLOCK_IMX7D_H */
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================