Kconfig: Convert commands (D to L) to Kconfig
Subsystems (23)
cover Kconfig: Convert commands (D to L) to Kconfig
This series moves more commands to Kconfig.
There are two points of note:
- A patch is included to drop the whole digital thermometer and thermostat (DTT) subsystem. It has been replaced with UCLASS_THERMAL and boards should be using that instead.
- Also included is a patch to drop three-wire serial (TWS) support. This is only used by one board and does not support driver model.
These two patches can be applied now, or delayed until a better time.
Simon Glass (47):
configs: Re-sync
Kconfig: Drop CONFIG_CMD_DS4510_INFO
Kconfig: Drop CONFIG_CMD_DS4510_MEM
Kconfig: Drop CONFIG_CMD_DS4510_RST
Kconfig: Drop CONFIG_CMD_DS4510
Convert CONFIG_DS4510 to Kconfig
Kconfig: Drop CONFIG_SYS_I2C_DTT_ADDR
Drop three-wire serial (TWS) support
Drop digital thermometer and thermostat (DTT) drivers
Kconfig: Drop CONFIG_SYS_I2C_DS1621_ADDR
Kconfig: Drop CONFIG_SYS_I2C_DS4510_ADDR Convert CONFIG_CMD_ECCTEST to Kconfig Convert CONFIG_CMD_EECONFIG to Kconfig Convert CONFIG_CMD_EEPROM et al to Kconfig Convert CONFIG_CMD_ENTERRCM to Kconfig Convert CONFIG_CMD_ENV to Kconfig
Convert CONFIG_CMD_ENV_CALLBACK to Kconfig Convert CONFIG_CMD_ENV_FLAGS to Kconfig Convert CONFIG_CMD_ERRATA to Kconfig
Convert CONFIG_CMD_ESBC_VALIDATE to Kconfig Convert CONFIG_CMD_ETHSW to Kconfig
Convert CONFIG_CMD_FDC to Kconfig
Kconfig: Drop CONFIG_CMD_FDT_MAX_DUMP Convert CONFIG_CMD_FPGAD to Kconfig
Convert CONFIG_CMD_FPGA_LOADBP et al to Kconfig Convert CONFIG_CMD_FUSE to Kconfig
Convert CONFIG_CMD_GETTIME to Kconfig Convert CONFIG_CMD_GSC to Kconfig
Convert CONFIG_CMD_HASH to Kconfig
Kconfig: Add CONFIG_HASH to enable hashing API Convert CONFIG_CMD_HD44760 to Kconfig Convert CONFIG_CMD_HDMIDETECT to Kconfig Convert CONFIG_CMD_IDE to Kconfig
Kconfig: Add a CONFIG_IDE option
Convert CONFIG_CMD_IMMAP to Kconfig
Kconfig: Drop CONFIG_CMD_IMXOTP
Kconfig: Drop CONFIG_CMD_IMX_FUSE
Convert CONFIG_CMD_IO to Kconfig
Convert CONFIG_CMD_IOLOOP to Kconfig
Convert CONFIG_CMD_IOTRACE to Kconfig Convert CONFIG_CMD_JFFS2 to Kconfig
fs: Kconfig: Add a separate option for FS_JFFS2 Convert CONFIG_CMD_IRQ to Kconfig
Convert CONFIG_CMD_KGDB to Kconfig
Kconfig: Drop CONFIG_CMD_LOADY
Convert CONFIG_LZMA to Kconfig
Convert CONFIG_CMD_LZMADEC to Kconfig
README | 78 +------
api/api_storage.c | 2 +-
arch/Kconfig | 8 +
arch/arm/Kconfig | 2 +
arch/arm/cpu/armv7/ls102xa/Kconfig | 1 +
arch/arm/cpu/armv7/mx6/Kconfig | 1 +
arch/arm/cpu/armv7/mx7/Kconfig | 2 +
arch/arm/cpu/armv8/fsl-layerscape/Kconfig | 4 +
arch/arm/imx-common/Kconfig | 6 +
arch/arm/include/asm/fsl_secure_boot.h | 2 -
arch/arm/mach-exynos/Kconfig | 1 +
arch/arm/mach-kirkwood/include/mach/config.h | 6 +-
arch/arm/mach-omap2/Kconfig | 1 +
arch/arm/mach-omap2/am33xx/Kconfig | 1 +
arch/arm/mach-tegra/Kconfig | 16 ++
arch/powerpc/Kconfig | 3 +
arch/powerpc/cpu/mpc5xxx/ide.c | 2 +-
arch/powerpc/cpu/mpc85xx/Kconfig | 50 +++++
arch/powerpc/cpu/ppc4xx/Kconfig | 6 +
arch/powerpc/include/asm/fsl_secure_boot.h | 1 -
arch/powerpc/lib/Kconfig | 8 +
arch/powerpc/lib/Makefile | 3 +-
{cmd => arch/powerpc/lib}/immap.c | 0
board/freescale/common/Kconfig | 8 +
board/freescale/m5253demo/m5253demo.c | 4 +-
board/freescale/m5253evbe/m5253evbe.c | 4 +-
board/freescale/m54455evb/m54455evb.c | 2 +-
board/gateworks/gw_ventana/Kconfig | 13 ++
board/gdsys/405ep/dlvision-10g.c | 10 +-
board/gdsys/405ep/io.c | 10 +-
board/gdsys/405ep/neo.c | 10 +-
board/gdsys/405ex/io64.c | 10 +-
board/gdsys/mpc8308/Kconfig | 5 +
board/intercontrol/digsy_mtc/digsy_mtc.c | 4 +-
board/jupiter/jupiter.c | 2 +-
board/phytec/pcm030/pcm030.c | 4 +-
board/tqc/tqm5200/tqm5200.c | 2 +-
board/v38b/v38b.c | 2 +-
board/work-microwave/work_92105/Kconfig | 5 +
.../work-microwave/work_92105/work_92105_display.c | 2 +-
cmd/Kconfig | 224 +++++++++++++++++++++
cmd/Makefile | 4 -
cmd/cramfs.c | 4 +-
cmd/dtt.c | 120 -----------
cmd/eeprom.c | 4 -
cmd/fdt.c | 8 +-
cmd/pcmcia.c | 2 +-
common/Kconfig | 12 ++
common/Makefile | 3 +-
common/board_r.c | 10 +-
common/hash.c | 4 +-
configs/B4420QDS_NAND_defconfig | 1 +
configs/B4420QDS_SPIFLASH_defconfig | 1 +
configs/B4420QDS_defconfig | 1 +
configs/B4860QDS_NAND_defconfig | 1 +
configs/B4860QDS_SECURE_BOOT_defconfig | 2 +
configs/B4860QDS_SPIFLASH_defconfig | 1 +
configs/B4860QDS_SRIO_PCIE_BOOT_defconfig | 1 +
configs/B4860QDS_defconfig | 1 +
configs/BSC9131RDB_NAND_SYSCLK100_defconfig | 1 +
configs/BSC9131RDB_NAND_defconfig | 1 +
configs/BSC9131RDB_SPIFLASH_SYSCLK100_defconfig | 1 +
configs/BSC9131RDB_SPIFLASH_defconfig | 1 +
configs/BSC9132QDS_NAND_DDRCLK100_SECURE_defconfig | 1 +
configs/BSC9132QDS_NAND_DDRCLK133_SECURE_defconfig | 1 +
configs/BSC9132QDS_NOR_DDRCLK100_SECURE_defconfig | 1 +
configs/BSC9132QDS_NOR_DDRCLK133_SECURE_defconfig | 1 +
.../BSC9132QDS_SDCARD_DDRCLK100_SECURE_defconfig | 1 +
.../BSC9132QDS_SDCARD_DDRCLK133_SECURE_defconfig | 1 +
.../BSC9132QDS_SPIFLASH_DDRCLK100_SECURE_defconfig | 1 +
.../BSC9132QDS_SPIFLASH_DDRCLK133_SECURE_defconfig | 1 +
configs/C29XPCIE_NAND_defconfig | 2 +
configs/C29XPCIE_NOR_SECBOOT_defconfig | 3 +
configs/C29XPCIE_SPIFLASH_SECBOOT_defconfig | 3 +
configs/C29XPCIE_SPIFLASH_defconfig | 2 +
configs/C29XPCIE_defconfig | 2 +
configs/CPCI2DP_defconfig | 2 +
configs/CPCI4052_defconfig | 3 +
configs/M52277EVB_defconfig | 1 +
configs/M52277EVB_stmicro_defconfig | 1 +
configs/M5253DEMO_defconfig | 1 +
configs/M5253EVBE_defconfig | 1 +
configs/M54455EVB_a66_defconfig | 2 +
configs/M54455EVB_defconfig | 2 +
configs/M54455EVB_i66_defconfig | 2 +
configs/M54455EVB_intel_defconfig | 2 +
configs/M54455EVB_stm33_defconfig | 2 +
configs/MIP405T_defconfig | 4 +
configs/MIP405_defconfig | 4 +
configs/MPC8323ERDB_defconfig | 1 +
configs/MPC8349ITXGP_defconfig | 1 +
configs/MPC8349ITX_LOWBOOT_defconfig | 2 +
configs/MPC8349ITX_defconfig | 2 +
configs/MPC8536DS_36BIT_defconfig | 1 +
configs/MPC8536DS_SDCARD_defconfig | 1 +
configs/MPC8536DS_SPIFLASH_defconfig | 1 +
configs/MPC8536DS_defconfig | 1 +
configs/MPC8540ADS_defconfig | 1 +
configs/MPC8541CDS_defconfig | 1 +
configs/MPC8541CDS_legacy_defconfig | 1 +
configs/MPC8544DS_defconfig | 1 +
configs/MPC8548CDS_36BIT_defconfig | 1 +
configs/MPC8548CDS_defconfig | 1 +
configs/MPC8548CDS_legacy_defconfig | 1 +
configs/MPC8555CDS_defconfig | 1 +
configs/MPC8555CDS_legacy_defconfig | 1 +
configs/MPC8560ADS_defconfig | 1 +
configs/MPC8568MDS_defconfig | 1 +
configs/MPC8569MDS_ATM_defconfig | 1 +
configs/MPC8569MDS_defconfig | 1 +
configs/MPC8572DS_36BIT_defconfig | 1 +
configs/MPC8572DS_defconfig | 1 +
configs/MiniFAP_defconfig | 3 +
configs/O2D300_defconfig | 1 +
configs/O2DNT2_RAMBOOT_defconfig | 1 +
configs/O2DNT2_defconfig | 1 +
configs/O2D_defconfig | 1 +
configs/O2I_defconfig | 1 +
configs/O2MNT_O2M110_defconfig | 1 +
configs/O2MNT_O2M112_defconfig | 1 +
configs/O2MNT_O2M113_defconfig | 1 +
configs/O2MNT_defconfig | 1 +
configs/O3DNT_defconfig | 1 +
configs/P1010RDB-PA_36BIT_NAND_SECBOOT_defconfig | 1 +
configs/P1010RDB-PA_36BIT_NOR_SECBOOT_defconfig | 1 +
.../P1010RDB-PA_36BIT_SPIFLASH_SECBOOT_defconfig | 1 +
configs/P1010RDB-PA_NAND_SECBOOT_defconfig | 1 +
configs/P1010RDB-PA_NOR_SECBOOT_defconfig | 1 +
configs/P1010RDB-PA_SPIFLASH_SECBOOT_defconfig | 1 +
configs/P1010RDB-PB_36BIT_NAND_SECBOOT_defconfig | 1 +
configs/P1010RDB-PB_36BIT_NOR_SECBOOT_defconfig | 1 +
.../P1010RDB-PB_36BIT_SPIFLASH_SECBOOT_defconfig | 1 +
configs/P1010RDB-PB_NAND_SECBOOT_defconfig | 1 +
configs/P1010RDB-PB_NOR_SECBOOT_defconfig | 1 +
configs/P1010RDB-PB_SPIFLASH_SECBOOT_defconfig | 1 +
configs/P1022DS_36BIT_NAND_defconfig | 1 +
configs/P1022DS_36BIT_SDCARD_defconfig | 1 +
configs/P1022DS_36BIT_SPIFLASH_defconfig | 1 +
configs/P1022DS_36BIT_defconfig | 1 +
configs/P1022DS_NAND_defconfig | 1 +
configs/P1022DS_SDCARD_defconfig | 1 +
configs/P1022DS_SPIFLASH_defconfig | 1 +
configs/P1022DS_defconfig | 1 +
configs/P1023RDB_defconfig | 1 +
configs/P2020RDB-PC_36BIT_NAND_defconfig | 1 +
configs/P2020RDB-PC_36BIT_SDCARD_defconfig | 1 +
configs/P2020RDB-PC_36BIT_SPIFLASH_defconfig | 1 +
configs/P2020RDB-PC_36BIT_defconfig | 1 +
configs/P2020RDB-PC_NAND_defconfig | 1 +
configs/P2020RDB-PC_SDCARD_defconfig | 1 +
configs/P2020RDB-PC_SPIFLASH_defconfig | 1 +
configs/P2020RDB-PC_defconfig | 1 +
configs/P2041RDB_NAND_defconfig | 1 +
configs/P2041RDB_SDCARD_defconfig | 1 +
configs/P2041RDB_SECURE_BOOT_defconfig | 2 +
configs/P2041RDB_SPIFLASH_defconfig | 1 +
configs/P2041RDB_SRIO_PCIE_BOOT_defconfig | 1 +
configs/P2041RDB_defconfig | 1 +
configs/P3041DS_NAND_SECURE_BOOT_defconfig | 1 +
configs/P3041DS_SECURE_BOOT_defconfig | 1 +
configs/P4080DS_SECURE_BOOT_defconfig | 1 +
configs/P5020DS_NAND_SECURE_BOOT_defconfig | 1 +
configs/P5020DS_SECURE_BOOT_defconfig | 1 +
configs/P5040DS_NAND_SECURE_BOOT_defconfig | 1 +
configs/P5040DS_SECURE_BOOT_defconfig | 1 +
configs/PATI_defconfig | 2 +
configs/PIP405_defconfig | 4 +
configs/PLU405_defconfig | 3 +
configs/PMC405DE_defconfig | 2 +
configs/PMC440_defconfig | 1 +
configs/Sinovoip_BPI_M2_Plus_defconfig | 1 -
configs/T1023RDB_SECURE_BOOT_defconfig | 1 +
configs/T1024QDS_DDR4_SECURE_BOOT_defconfig | 1 +
configs/T1024QDS_SECURE_BOOT_defconfig | 1 +
configs/T1024RDB_SECURE_BOOT_defconfig | 1 +
configs/T1040D4RDB_NAND_defconfig | 1 +
configs/T1040D4RDB_SDCARD_defconfig | 1 +
configs/T1040D4RDB_SECURE_BOOT_defconfig | 2 +
configs/T1040D4RDB_SPIFLASH_defconfig | 1 +
configs/T1040D4RDB_defconfig | 1 +
configs/T1040QDS_DDR4_defconfig | 1 +
configs/T1040QDS_SECURE_BOOT_defconfig | 2 +
configs/T1040QDS_defconfig | 1 +
configs/T1040RDB_NAND_defconfig | 1 +
configs/T1040RDB_SDCARD_defconfig | 1 +
configs/T1040RDB_SECURE_BOOT_defconfig | 2 +
configs/T1040RDB_SPIFLASH_defconfig | 1 +
configs/T1040RDB_defconfig | 1 +
configs/T1042D4RDB_SECURE_BOOT_defconfig | 1 +
configs/T1042RDB_PI_NAND_SECURE_BOOT_defconfig | 1 +
configs/T1042RDB_SECURE_BOOT_defconfig | 1 +
configs/T2080QDS_NAND_defconfig | 1 +
configs/T2080QDS_SDCARD_defconfig | 1 +
configs/T2080QDS_SECURE_BOOT_defconfig | 2 +
configs/T2080QDS_SPIFLASH_defconfig | 1 +
configs/T2080QDS_SRIO_PCIE_BOOT_defconfig | 1 +
configs/T2080QDS_defconfig | 1 +
configs/T2080RDB_SECURE_BOOT_defconfig | 1 +
configs/T4160QDS_SECURE_BOOT_defconfig | 1 +
configs/T4240QDS_SECURE_BOOT_defconfig | 1 +
configs/TQM5200S_HIGHBOOT_defconfig | 3 +
configs/TQM5200S_defconfig | 3 +
configs/TQM5200_B_HIGHBOOT_defconfig | 3 +
configs/TQM5200_B_defconfig | 3 +
configs/TQM5200_STK100_defconfig | 3 +
configs/TQM5200_defconfig | 3 +
configs/TQM823L_LCD_defconfig | 2 +
configs/TQM823L_defconfig | 2 +
configs/TQM823M_defconfig | 2 +
configs/TQM834x_defconfig | 2 +
configs/TQM850L_defconfig | 2 +
configs/TQM850M_defconfig | 2 +
configs/TQM855L_defconfig | 2 +
configs/TQM855M_defconfig | 3 +
configs/TQM860L_defconfig | 2 +
configs/TQM860M_defconfig | 2 +
configs/TQM862L_defconfig | 2 +
configs/TQM862M_defconfig | 2 +
configs/TQM866M_defconfig | 3 +
configs/TQM885D_defconfig | 2 +
configs/TTTech_defconfig | 2 +
configs/TWR-P1025_defconfig | 1 +
configs/VOM405_defconfig | 2 +
configs/a4m072_defconfig | 2 +
configs/ac14xx_defconfig | 2 +
configs/acadia_defconfig | 2 +
configs/am335x_baltos_defconfig | 5 +-
configs/am335x_evm_defconfig | 1 -
configs/am335x_hs_evm_defconfig | 3 -
configs/am335x_igep003x_defconfig | 6 +-
configs/am335x_shc_defconfig | 4 +-
configs/am335x_shc_ict_defconfig | 4 +-
configs/am335x_shc_netboot_defconfig | 4 +-
configs/am335x_shc_prompt_defconfig | 4 +-
configs/am335x_shc_sdboot_defconfig | 4 +-
configs/am335x_shc_sdboot_prompt_defconfig | 4 +-
configs/am335x_sl50_defconfig | 5 +-
configs/am3517_crane_defconfig | 1 +
configs/am43xx_evm_defconfig | 2 +-
configs/am43xx_hs_evm_defconfig | 2 +-
configs/am57xx_evm_defconfig | 4 +-
configs/am57xx_hs_evm_defconfig | 4 +-
configs/ap121_defconfig | 1 +
configs/ap143_defconfig | 1 +
configs/ap325rxa_defconfig | 1 +
configs/apalis_imx6_defconfig | 1 +
configs/apalis_imx6_nospl_com_defconfig | 1 +
configs/apalis_imx6_nospl_it_defconfig | 1 +
configs/apf27_defconfig | 1 +
configs/arches_defconfig | 2 +
configs/aria_defconfig | 2 +
configs/astro_mcf5373l_defconfig | 2 +
configs/at91sam9263ek_norflash_boot_defconfig | 2 +-
configs/at91sam9263ek_norflash_defconfig | 2 +-
configs/atngw100_defconfig | 1 +
configs/atngw100mkii_defconfig | 1 +
configs/atstk1002_defconfig | 1 +
configs/bamboo_defconfig | 2 +
configs/bayleybay_defconfig | 1 +
configs/bcm958622hr_defconfig | 1 +
configs/birdland_bav335a_defconfig | 3 +-
configs/birdland_bav335b_defconfig | 3 +-
configs/bk4r1_defconfig | 1 +
configs/brppt1_mmc_defconfig | 2 +-
configs/brppt1_nand_defconfig | 2 +-
configs/brppt1_spi_defconfig | 2 +-
configs/brxre1_defconfig | 2 +-
configs/bubinga_defconfig | 2 +
configs/cam5200_defconfig | 2 +
configs/cam5200_niosflash_defconfig | 2 +
configs/canmb_defconfig | 1 +
configs/canyonlands_defconfig | 2 +
configs/charon_defconfig | 3 +
configs/chiliboard_defconfig | 4 +-
configs/chromebook_link64_defconfig | 1 +
configs/chromebook_link_defconfig | 1 +
configs/chromebook_minnie_defconfig | 2 +-
configs/chromebook_samus_defconfig | 1 +
configs/chromebox_panther_defconfig | 1 +
configs/cl-som-am57x_defconfig | 2 +
configs/cm5200_defconfig | 1 +
configs/cm_fx6_defconfig | 4 +-
configs/cm_t335_defconfig | 4 +-
configs/cm_t3517_defconfig | 2 +
configs/cm_t35_defconfig | 2 +
configs/cm_t43_defconfig | 4 +-
configs/cm_t54_defconfig | 2 +
configs/colibri_imx6_defconfig | 1 +
configs/colibri_imx6_nospl_defconfig | 1 +
configs/colibri_imx7_defconfig | 2 +-
configs/colibri_vf_defconfig | 3 +-
configs/comtrend_ar5387un_ram_defconfig | 65 +++---
configs/comtrend_vr3032u_ram_defconfig | 66 +++---
...conga-qeval20-qa3-e3845-internal-uart_defconfig | 1 +
configs/conga-qeval20-qa3-e3845_defconfig | 1 +
.../controlcenterd_36BIT_SDCARD_DEVELOP_defconfig | 2 +
configs/controlcenterd_36BIT_SDCARD_defconfig | 2 +
.../controlcenterd_TRAILBLAZER_DEVELOP_defconfig | 2 +
configs/controlcenterd_TRAILBLAZER_defconfig | 2 +
configs/coreboot-x86_defconfig | 2 +
configs/cougarcanyon2_defconfig | 1 +
configs/crownbay_defconfig | 1 +
configs/d2net_v2_defconfig | 2 +
configs/dbau1000_defconfig | 1 +
configs/dbau1100_defconfig | 1 +
configs/dbau1500_defconfig | 1 +
configs/devconcenter_defconfig | 2 +
configs/devkit3250_defconfig | 1 +
configs/devkit8000_defconfig | 1 +
configs/dfi-bt700-q7x-151_defconfig | 1 +
configs/digsy_mtc_RAMBOOT_defconfig | 3 +
configs/digsy_mtc_defconfig | 3 +
configs/digsy_mtc_rev5_RAMBOOT_defconfig | 3 +
configs/digsy_mtc_rev5_defconfig | 3 +
configs/dns325_defconfig | 2 +
configs/dockstar_defconfig | 1 +
configs/dra7xx_evm_defconfig | 11 +-
configs/dra7xx_hs_evm_defconfig | 8 +-
configs/dreamplug_defconfig | 1 +
configs/ds109_defconfig | 1 +
configs/ds414_defconfig | 1 +
configs/eco5pk_defconfig | 1 +
configs/edb9315a_defconfig | 1 +
configs/edminiv2_defconfig | 1 +
configs/efi-x86_defconfig | 1 +
configs/ethernut5_defconfig | 1 +
configs/evb-ast2500_defconfig | 12 +-
configs/evb-rk3399_defconfig | 5 +-
configs/firefly-rk3399_defconfig | 1 -
configs/fo300_defconfig | 3 +
configs/galileo_defconfig | 1 +
configs/gdppc440etx_defconfig | 1 +
configs/glacier_defconfig | 2 +
configs/glacier_ramboot_defconfig | 2 +
configs/goflexhome_defconfig | 2 +
configs/grasshopper_defconfig | 1 +
configs/guruplug_defconfig | 3 +
configs/gwventana_emmc_defconfig | 5 +-
configs/gwventana_gw5904_defconfig | 5 +-
configs/gwventana_nand_defconfig | 5 +-
configs/haleakala_defconfig | 2 +
configs/hrcon_defconfig | 2 +
configs/hrcon_dh_defconfig | 2 +
configs/huawei_hg556a_ram_defconfig | 67 +++---
configs/ib62x0_defconfig | 3 +
configs/icon_defconfig | 2 +
configs/iconnect_defconfig | 2 +
configs/ids8313_defconfig | 3 +
configs/imx31_phycore_defconfig | 1 +
configs/imx31_phycore_eet_defconfig | 1 +
configs/imx6dl_icore_mmc_defconfig | 2 +-
configs/imx6dl_icore_nand_defconfig | 2 +-
configs/imx6q_icore_mmc_defconfig | 2 +-
configs/imx6q_icore_nand_defconfig | 2 +-
configs/inetspace_v2_defconfig | 2 +
configs/inka4x0_defconfig | 2 +-
configs/intip_defconfig | 2 +
configs/io64_defconfig | 2 +
configs/iocon_defconfig | 1 +
configs/ipek01_defconfig | 2 +
configs/k2e_evm_defconfig | 5 +-
configs/k2e_hs_evm_defconfig | 3 +-
configs/k2g_evm_defconfig | 4 +-
configs/k2g_hs_evm_defconfig | 5 +-
configs/k2hk_evm_defconfig | 4 +-
configs/k2hk_hs_evm_defconfig | 3 +-
configs/k2l_evm_defconfig | 4 +-
configs/katmai_defconfig | 3 +
configs/kilauea_defconfig | 2 +
configs/km_kirkwood_128m16_defconfig | 2 +
configs/km_kirkwood_defconfig | 2 +
configs/km_kirkwood_pci_defconfig | 2 +
configs/kmcoge4_defconfig | 3 +
configs/kmcoge5ne_defconfig | 3 +
configs/kmcoge5un_defconfig | 2 +
configs/kmeter1_defconfig | 3 +
configs/kmlion1_defconfig | 3 +
configs/kmnusa_defconfig | 2 +
configs/kmopti2_defconfig | 3 +
configs/kmsugp1_defconfig | 2 +
configs/kmsupx5_defconfig | 3 +
configs/kmsuv31_defconfig | 2 +
configs/kmtegr1_defconfig | 3 +
configs/kmtepr2_defconfig | 3 +
configs/kmvect1_defconfig | 3 +
configs/ls1012aqds_qspi_defconfig | 1 +
configs/ls1012ardb_qspi_SECURE_BOOT_defconfig | 1 +
configs/ls1021aqds_nor_SECURE_BOOT_defconfig | 1 +
configs/ls1021atwr_nor_SECURE_BOOT_defconfig | 1 +
.../ls1021atwr_sdcard_ifc_SECURE_BOOT_defconfig | 1 +
configs/ls1043ardb_SECURE_BOOT_defconfig | 1 +
configs/ls1043ardb_nand_SECURE_BOOT_defconfig | 1 +
configs/ls1043ardb_sdcard_SECURE_BOOT_defconfig | 1 +
configs/ls1046aqds_SECURE_BOOT_defconfig | 1 +
configs/ls1046ardb_qspi_SECURE_BOOT_defconfig | 1 +
configs/ls1046ardb_sdcard_SECURE_BOOT_defconfig | 1 +
configs/ls2080aqds_SECURE_BOOT_defconfig | 2 +
configs/ls2080aqds_defconfig | 1 +
configs/ls2080aqds_nand_defconfig | 1 +
configs/ls2080aqds_qspi_defconfig | 1 +
configs/ls2080ardb_SECURE_BOOT_defconfig | 2 +
configs/ls2080ardb_defconfig | 1 +
configs/ls2080ardb_nand_defconfig | 1 +
configs/lschlv2_defconfig | 1 +
configs/lsxhl_defconfig | 1 +
configs/luan_defconfig | 2 +
configs/lwmon5_defconfig | 2 +
configs/m28evk_defconfig | 1 +
configs/m53evk_defconfig | 2 +-
configs/makalu_defconfig | 2 +
configs/malta64_defconfig | 1 +
configs/malta64el_defconfig | 1 +
configs/malta_defconfig | 1 +
configs/maltael_defconfig | 1 +
configs/mcx_defconfig | 1 +
configs/mecp5123_defconfig | 2 +
configs/mgcoge3ne_defconfig | 3 +
configs/mgcoge3un_defconfig | 2 +
configs/mgcoge_defconfig | 3 +
configs/microblaze-generic_defconfig | 2 +
configs/minnowmax_defconfig | 1 +
configs/motionpro_defconfig | 4 +
configs/mpc5121ads_defconfig | 3 +
configs/mpc5121ads_rev2_defconfig | 3 +
configs/ms7720se_defconfig | 1 +
configs/ms7722se_defconfig | 1 +
configs/mt_ventoux_defconfig | 2 +
configs/munices_defconfig | 1 +
configs/mvebu_db-88f7040-nand_defconfig | 7 +-
configs/mx51evk_defconfig | 3 +-
configs/mx53cx9020_defconfig | 2 +-
configs/mx53loco_defconfig | 2 +-
configs/mx6cuboxi_defconfig | 3 +-
configs/mx6qsabrelite_defconfig | 1 +
configs/mx6sxsabresd_defconfig | 2 +-
configs/mx6sxsabresd_spl_defconfig | 2 +-
configs/mx7dsabresd_defconfig | 2 +-
configs/mx7dsabresd_secure_defconfig | 2 +-
configs/nanopi_neo_air_defconfig | 2 +-
configs/nanopi_neo_defconfig | 2 +-
configs/nas220_defconfig | 2 +
configs/net2big_v2_defconfig | 2 +
configs/netspace_lite_v2_defconfig | 2 +
configs/netspace_max_v2_defconfig | 2 +
configs/netspace_mini_v2_defconfig | 2 +
configs/netspace_v2_defconfig | 2 +
configs/nitrogen6dl2g_defconfig | 1 +
configs/nitrogen6dl_defconfig | 1 +
configs/nitrogen6q2g_defconfig | 1 +
configs/nitrogen6q_defconfig | 1 +
configs/nitrogen6s1g_defconfig | 1 +
configs/nitrogen6s_defconfig | 1 +
configs/novena_defconfig | 4 +-
configs/nsa310s_defconfig | 3 +
configs/omap3_evm_defconfig | 1 +
configs/omap3_logic_defconfig | 1 -
configs/openrd_base_defconfig | 2 +
configs/openrd_client_defconfig | 2 +
configs/openrd_ultimate_defconfig | 2 +
configs/opos6uldev_defconfig | 2 +-
configs/orangepi_2_defconfig | 1 -
configs/orangepi_lite_defconfig | 1 -
configs/orangepi_one_defconfig | 1 -
configs/orangepi_pc2_defconfig | 1 -
configs/orangepi_pc_defconfig | 1 -
configs/orangepi_pc_plus_defconfig | 1 -
configs/orangepi_plus2e_defconfig | 1 -
configs/orangepi_plus_defconfig | 1 -
configs/orangepi_zero_defconfig | 2 +-
configs/ot1200_defconfig | 1 +
configs/pcm030_LOWBOOT_defconfig | 2 +
configs/pcm030_defconfig | 2 +
configs/pcm051_rev1_defconfig | 3 +-
configs/pcm051_rev3_defconfig | 3 +-
configs/pcm052_defconfig | 1 +
configs/pcm058_defconfig | 1 +
configs/pdm360ng_defconfig | 1 +
configs/pengwyn_defconfig | 3 +-
configs/pepper_defconfig | 2 +-
configs/pine64_plus_defconfig | 1 -
configs/pm9263_defconfig | 1 +
configs/pm9g45_defconfig | 1 +
configs/pogo_e02_defconfig | 1 +
configs/portl2_defconfig | 2 +
configs/pxm2_defconfig | 2 +-
configs/qemu-ppce500_defconfig | 1 +
configs/qemu-x86_64_defconfig | 2 +
configs/qemu-x86_defconfig | 2 +
configs/qemu-x86_efi_payload32_defconfig | 2 +
configs/qemu-x86_efi_payload64_defconfig | 2 +
configs/qemu_mips64_defconfig | 2 +
configs/qemu_mips64el_defconfig | 2 +
configs/qemu_mips_defconfig | 2 +
configs/qemu_mipsel_defconfig | 2 +
configs/r2dplus_defconfig | 1 +
configs/r7780mp_defconfig | 1 +
configs/rainier_defconfig | 2 +
configs/rainier_ramboot_defconfig | 2 +
configs/redwood_defconfig | 2 +
configs/rut_defconfig | 2 +-
configs/sama5d2_xplained_mmc_defconfig | 4 +-
configs/sama5d2_xplained_spiflash_defconfig | 2 +-
configs/sandbox_defconfig | 12 +-
configs/sandbox_noblk_defconfig | 7 +-
configs/sandbox_spl_defconfig | 7 +-
configs/sequoia_defconfig | 2 +
configs/sequoia_ramboot_defconfig | 2 +
configs/sfr_nb4-ser_ram_defconfig | 67 +++---
configs/sh7763rdp_defconfig | 1 +
configs/sheevaplug_defconfig | 3 +
configs/socfpga_vining_fpga_defconfig | 1 +
configs/som-db5800-som-6867_defconfig | 1 +
configs/stm32f746-disco_defconfig | 14 +-
configs/strider_con_defconfig | 2 +
configs/strider_con_dp_defconfig | 2 +
configs/strider_cpu_defconfig | 2 +
configs/strider_cpu_dp_defconfig | 2 +
configs/suvd3_defconfig | 3 +
configs/sycamore_defconfig | 2 +
configs/t3corp_defconfig | 3 +
configs/tbs2910_defconfig | 2 +-
configs/theadorable-x86-dfi-bt700_defconfig | 1 +
configs/tplink_wdr4300_defconfig | 1 +
configs/tqma6dl_mba6_mmc_defconfig | 1 +
configs/tqma6dl_mba6_spi_defconfig | 1 +
configs/tqma6q_mba6_mmc_defconfig | 1 +
configs/tqma6q_mba6_spi_defconfig | 1 +
configs/tqma6s_mba6_mmc_defconfig | 1 +
configs/tqma6s_mba6_spi_defconfig | 1 +
configs/tqma6s_wru4_mmc_defconfig | 1 +
configs/tricorder_defconfig | 1 +
configs/tricorder_flash_defconfig | 1 +
configs/tuge1_defconfig | 3 +
configs/tuxx1_defconfig | 3 +
configs/twister_defconfig | 1 +
configs/usbarmory_defconfig | 1 +
configs/v38b_defconfig | 3 +
configs/vct_platinum_defconfig | 1 +
configs/vct_platinum_onenand_defconfig | 2 +
configs/vct_platinum_onenand_small_defconfig | 1 +
configs/vct_platinumavc_defconfig | 1 +
configs/vct_platinumavc_onenand_defconfig | 2 +
configs/vct_platinumavc_onenand_small_defconfig | 1 +
configs/vct_premium_defconfig | 1 +
configs/vct_premium_onenand_defconfig | 2 +
configs/vct_premium_onenand_small_defconfig | 1 +
configs/vf610twr_defconfig | 1 +
configs/vf610twr_nand_defconfig | 1 +
configs/walnut_defconfig | 2 +
configs/wandboard_defconfig | 1 +
configs/work_92105_defconfig | 2 +
configs/wtk_defconfig | 2 +
configs/x600_defconfig | 1 +
configs/xilinx-ppc405-generic_defconfig | 2 +
configs/xilinx-ppc440-generic_defconfig | 2 +
configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 2 +-
configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 2 +-
configs/xilinx_zynqmp_zcu102_defconfig | 3 +-
configs/xilinx_zynqmp_zcu102_revB_defconfig | 3 +-
configs/xpedite1000_defconfig | 3 +
configs/xpedite517x_defconfig | 4 +
configs/xpedite520x_defconfig | 2 +
configs/xpedite537x_defconfig | 3 +
configs/xpedite550x_defconfig | 1 +
configs/yellowstone_defconfig | 2 +
configs/yosemite_defconfig | 2 +
configs/yucca_defconfig | 2 +
configs/zipitz2_defconfig | 1 +
configs/zynq_microzed_defconfig | 4 +
configs/zynq_picozed_defconfig | 4 +
configs/zynq_zc702_defconfig | 5 +
configs/zynq_zc706_defconfig | 5 +
configs/zynq_zc770_xm010_defconfig | 4 +
configs/zynq_zc770_xm011_defconfig | 4 +
configs/zynq_zc770_xm012_defconfig | 4 +
configs/zynq_zc770_xm013_defconfig | 4 +
configs/zynq_zed_defconfig | 4 +
configs/zynq_zybo_defconfig | 5 +
doc/README.JFFS2 | 3 +
drivers/Kconfig | 2 -
drivers/Makefile | 2 -
drivers/block/Kconfig | 8 +
drivers/block/Makefile | 1 +
{common => drivers/block}/ide.c | 0
drivers/block/sil680.c | 2 +-
drivers/hwmon/Kconfig | 0
drivers/hwmon/Makefile | 22 --
drivers/hwmon/adm1021.c | 164 ---------------
drivers/hwmon/adt7460.c | 73 -------
drivers/hwmon/ds1621.c | 155 --------------
drivers/hwmon/ds1722.c | 137 -------------
drivers/hwmon/ds1775.c | 126 ------------
drivers/hwmon/ds620.c | 65 ------
drivers/hwmon/lm63.c | 160 ---------------
drivers/hwmon/lm73.c | 146 --------------
drivers/hwmon/lm75.c | 143 -------------
drivers/hwmon/lm81.c | 111 ----------
drivers/misc/Kconfig | 8 +
drivers/misc/ds4510.c | 53 +----
{include => drivers/misc}/ds4510.h | 10 -
drivers/pcmcia/marubun_pcmcia.c | 2 +-
drivers/pcmcia/mpc8xx_pcmcia.c | 2 +-
drivers/pcmcia/tqm8xx_pcmcia.c | 2 +-
drivers/rtc/Makefile | 1 -
drivers/rtc/rtc4543.c | 101 ----------
drivers/twserial/Makefile | 8 -
drivers/twserial/soft_tws.c | 94 ---------
fs/Makefile | 2 +-
fs/fat/fat.c | 2 +-
fs/jffs2/Kconfig | 7 +
include/config_cmd_all.h | 12 --
include/config_distro_bootcmd.h | 6 +-
include/config_fallbacks.h | 2 +-
include/configs/B4860QDS.h | 4 -
include/configs/BSC9131RDB.h | 4 -
include/configs/BSC9132QDS.h | 4 -
include/configs/C29XPCIE.h | 4 -
include/configs/CPCI2DP.h | 2 -
include/configs/CPCI4052.h | 3 -
include/configs/M52277EVB.h | 1 -
include/configs/M5253DEMO.h | 3 +-
include/configs/M5253EVBE.h | 1 -
include/configs/M54418TWR.h | 1 -
include/configs/M54451EVB.h | 1 -
include/configs/M54455EVB.h | 2 -
include/configs/MIP405.h | 4 -
include/configs/MPC8323ERDB.h | 1 -
include/configs/MPC8349ITX.h | 5 -
include/configs/MPC8536DS.h | 2 -
include/configs/MPC8540ADS.h | 1 -
include/configs/MPC8541CDS.h | 1 -
include/configs/MPC8544DS.h | 1 -
include/configs/MPC8548CDS.h | 1 -
include/configs/MPC8555CDS.h | 1 -
include/configs/MPC8560ADS.h | 1 -
include/configs/MPC8568MDS.h | 1 -
include/configs/MPC8569MDS.h | 1 -
include/configs/MPC8572DS.h | 2 -
include/configs/P1010RDB.h | 4 -
include/configs/P1022DS.h | 2 -
include/configs/P1023RDB.h | 1 -
include/configs/P2041RDB.h | 3 -
include/configs/PATI.h | 2 -
include/configs/PIP405.h | 4 -
include/configs/PLU405.h | 3 -
include/configs/PMC405DE.h | 2 -
include/configs/PMC440.h | 22 --
include/configs/T102xQDS.h | 4 -
include/configs/T102xRDB.h | 4 -
include/configs/T1040QDS.h | 5 -
include/configs/T104xRDB.h | 4 -
include/configs/T208xQDS.h | 3 -
include/configs/T208xRDB.h | 2 -
include/configs/T4240QDS.h | 1 -
include/configs/T4240RDB.h | 3 -
include/configs/TQM5200.h | 3 -
include/configs/TQM823L.h | 2 -
include/configs/TQM823M.h | 2 -
include/configs/TQM834x.h | 10 -
include/configs/TQM850L.h | 2 -
include/configs/TQM850M.h | 2 -
include/configs/TQM855L.h | 2 -
include/configs/TQM855M.h | 3 -
include/configs/TQM860L.h | 2 -
include/configs/TQM860M.h | 2 -
include/configs/TQM862L.h | 2 -
include/configs/TQM862M.h | 2 -
include/configs/TQM866M.h | 3 -
include/configs/TQM885D.h | 2 -
include/configs/UCP1020.h | 24 ---
include/configs/VOM405.h | 2 -
include/configs/a4m072.h | 2 -
include/configs/ac14xx.h | 4 -
include/configs/acadia.h | 9 -
include/configs/advantech_dms-ba16.h | 1 -
include/configs/am335x_evm.h | 1 -
include/configs/am335x_sl50.h | 1 -
include/configs/am3517_crane.h | 1 -
include/configs/am43xx_evm.h | 1 -
include/configs/amcc-common.h | 2 -
include/configs/ap121.h | 1 -
include/configs/ap143.h | 1 -
include/configs/ap325rxa.h | 1 -
include/configs/ap_sh4a_4a.h | 1 -
include/configs/apalis_imx6.h | 2 -
include/configs/apf27.h | 2 -
include/configs/aria.h | 4 -
include/configs/astro_mcf5373l.h | 4 -
include/configs/atngw100.h | 1 -
include/configs/atngw100mkii.h | 1 -
include/configs/atstk1002.h | 1 -
include/configs/baltos.h | 1 -
include/configs/bav335x.h | 1 -
include/configs/bcm_ep_board.h | 1 -
include/configs/calimain.h | 1 -
include/configs/canmb.h | 1 -
include/configs/canyonlands.h | 15 --
include/configs/cl-som-am57x.h | 2 -
include/configs/clearfog.h | 1 -
include/configs/cm5200.h | 1 -
include/configs/cm_fx6.h | 4 -
include/configs/cm_t335.h | 4 -
include/configs/cm_t35.h | 4 -
include/configs/cm_t3517.h | 4 -
include/configs/cm_t43.h | 4 -
include/configs/cm_t54.h | 4 -
include/configs/colibri_imx6.h | 2 -
include/configs/colibri_pxa270.h | 1 -
include/configs/colibri_vf.h | 1 -
include/configs/controlcenterd.h | 3 -
include/configs/controlcenterdc.h | 1 -
include/configs/corenet_ds.h | 3 -
include/configs/cyrus.h | 2 -
include/configs/da850evm.h | 2 -
include/configs/db-88f6720.h | 1 -
include/configs/db-88f6820-amc.h | 1 -
include/configs/db-88f6820-gp.h | 1 -
include/configs/db-mv784mp-gp.h | 1 -
include/configs/dbau1x00.h | 6 -
include/configs/devkit3250.h | 1 -
include/configs/devkit8000.h | 1 -
include/configs/digsy_mtc.h | 3 -
include/configs/dlvision-10g.h | 10 -
include/configs/dlvision.h | 3 -
include/configs/dns325.h | 2 -
include/configs/dockstar.h | 2 -
include/configs/dragonboard410c.h | 1 -
include/configs/ds414.h | 1 -
include/configs/ea20.h | 2 -
include/configs/ecovec.h | 1 -
include/configs/edb93xx.h | 1 -
include/configs/edminiv2.h | 3 +-
include/configs/espt.h | 1 -
include/configs/ethernut5.h | 1 -
include/configs/exynos5-common.h | 5 -
include/configs/gdppc440etx.h | 1 -
include/configs/ge_bx50v3.h | 1 -
include/configs/goflexhome.h | 2 -
include/configs/grasshopper.h | 1 -
include/configs/gw_ventana.h | 4 -
include/configs/hikey.h | 1 -
include/configs/hrcon.h | 3 -
include/configs/ib62x0.h | 6 +-
include/configs/iconnect.h | 3 -
include/configs/ids8313.h | 3 -
include/configs/imx27lite-common.h | 1 -
include/configs/imx31_phycore.h | 1 -
include/configs/inka4x0.h | 81 --------
include/configs/intip.h | 8 -
include/configs/io.h | 8 -
include/configs/io64.h | 9 -
include/configs/iocon.h | 3 -
include/configs/ipam390.h | 1 -
include/configs/ipek01.h | 2 -
include/configs/katmai.h | 26 ---
include/configs/kilauea.h | 5 -
include/configs/km/keymile-common.h | 3 -
include/configs/km/km-powerpc.h | 1 -
include/configs/km/km83xx-common.h | 7 -
include/configs/km/kmp204x-common.h | 1 -
include/configs/km82xx.h | 7 -
include/configs/lacie_kw.h | 3 -
include/configs/ls1012a_common.h | 1 -
include/configs/ls1012aqds.h | 1 -
include/configs/ls1021aiot.h | 3 -
include/configs/ls1021aqds.h | 1 -
include/configs/ls1021atwr.h | 1 -
include/configs/ls1043a_common.h | 4 -
include/configs/ls1046a_common.h | 4 -
include/configs/ls2080a_common.h | 2 -
include/configs/ls2080aqds.h | 1 -
include/configs/ls2080ardb.h | 1 -
include/configs/lsxl.h | 4 +-
include/configs/lwmon5.h | 2 -
include/configs/m28evk.h | 1 -
include/configs/makalu.h | 6 -
include/configs/malta.h | 1 -
include/configs/maxbcm.h | 1 -
include/configs/mcx.h | 1 -
include/configs/mecp5123.h | 4 -
include/configs/meson-gxbb-common.h | 2 -
include/configs/microblaze-generic.h | 3 -
include/configs/motionpro.h | 7 -
include/configs/mpc5121ads.h | 9 +-
include/configs/ms7720se.h | 1 -
include/configs/ms7722se.h | 1 -
include/configs/mt_ventoux.h | 1 -
include/configs/munices.h | 1 -
include/configs/mv-common.h | 1 -
include/configs/mv-plug-common.h | 3 -
include/configs/mx51evk.h | 1 -
include/configs/mx6_common.h | 1 -
include/configs/mx6cuboxi.h | 1 -
include/configs/mx7_common.h | 1 -
include/configs/nas220.h | 2 -
include/configs/neo.h | 10 -
include/configs/nitrogen6x.h | 1 -
include/configs/novena.h | 2 -
include/configs/nsa310s.h | 6 +-
include/configs/o2dnt-common.h | 1 -
include/configs/odroid_xu3.h | 1 -
include/configs/omap3_evm.h | 2 -
include/configs/omapl138_lcdk.h | 2 -
include/configs/openrd.h | 2 -
include/configs/ot1200.h | 2 -
include/configs/p1_p2_rdb_pc.h | 2 -
include/configs/p1_twr.h | 2 -
include/configs/pb1x00.h | 2 -
include/configs/pcm030.h | 2 -
include/configs/pcm051.h | 1 -
include/configs/pcm052.h | 1 -
include/configs/pcm058.h | 3 -
include/configs/pdm360ng.h | 3 -
include/configs/pengwyn.h | 1 -
include/configs/pm9263.h | 1 -
include/configs/pm9g45.h | 1 -
include/configs/pogo_e02.h | 2 -
include/configs/qemu-mips.h | 4 -
include/configs/qemu-mips64.h | 4 -
include/configs/qemu-ppce500.h | 1 -
include/configs/qemu-x86.h | 5 +-
include/configs/r0p7734.h | 1 -
include/configs/r2dplus.h | 1 -
include/configs/r7780mp.h | 5 +-
include/configs/s32v234evb.h | 1 -
include/configs/sandbox.h | 10 -
include/configs/sequoia.h | 9 -
include/configs/sh7763rdp.h | 1 -
include/configs/sheevaplug.h | 4 +-
include/configs/shmin.h | 1 -
include/configs/socfpga_vining_fpga.h | 2 -
include/configs/socrates.h | 9 -
include/configs/spear-common.h | 1 -
include/configs/strider.h | 3 -
include/configs/t3corp.h | 1 -
include/configs/t4qds.h | 2 -
include/configs/tam3517-common.h | 1 -
include/configs/tbs2910.h | 1 -
include/configs/tegra-common.h | 2 -
include/configs/theadorable.h | 1 -
include/configs/ti_armv7_keystone2.h | 1 -
include/configs/topic_miami.h | 4 -
include/configs/tplink_wdr4300.h | 1 -
include/configs/tqma6.h | 11 -
include/configs/tqma6_mba6.h | 2 -
include/configs/tqma6_wru4.h | 4 -
include/configs/tricorder.h | 3 -
include/configs/usbarmory.h | 1 -
include/configs/v38b.h | 3 -
include/configs/vct.h | 6 -
include/configs/vexpress_aemv8a.h | 1 -
include/configs/vf610twr.h | 1 -
include/configs/vme8349.h | 4 -
include/configs/wandboard.h | 1 -
include/configs/work_92105.h | 10 -
include/configs/x600.h | 2 -
include/configs/x86-common.h | 4 -
include/configs/xilinx-ppc.h | 5 -
include/configs/xilinx_zynqmp.h | 2 -
include/configs/xilinx_zynqmp_zcu102.h | 1 -
include/configs/xpedite1000.h | 3 -
include/configs/xpedite517x.h | 24 ---
include/configs/xpedite520x.h | 2 -
include/configs/xpedite537x.h | 22 --
include/configs/xpedite550x.h | 5 -
include/configs/yosemite.h | 9 -
include/configs/zipitz2.h | 2 -
include/configs/zynq-common.h | 5 -
include/configs/zynq_zybo.h | 1 -
include/dtt.h | 47 -----
include/i2c.h | 3 -
include/pcmcia.h | 4 +-
include/tws.h | 21 --
lib/Kconfig | 8 +
scripts/config_whitelist.txt | 71 -------
875 files changed, 1474 insertions(+), 3142 deletions(-)
create mode 100644 arch/powerpc/lib/Kconfig
rename {cmd => arch/powerpc/lib}/immap.c (100%)
delete mode 100644 cmd/dtt.c
rename {common => drivers/block}/ide.c (100%)
delete mode 100644 drivers/hwmon/Kconfig
delete mode 100644 drivers/hwmon/Makefile
delete mode 100644 drivers/hwmon/adm1021.c
delete mode 100644 drivers/hwmon/adt7460.c
delete mode 100644 drivers/hwmon/ds1621.c
delete mode 100644 drivers/hwmon/ds1722.c
delete mode 100644 drivers/hwmon/ds1775.c
delete mode 100644 drivers/hwmon/ds620.c
delete mode 100644 drivers/hwmon/lm63.c
delete mode 100644 drivers/hwmon/lm73.c
delete mode 100644 drivers/hwmon/lm75.c
delete mode 100644 drivers/hwmon/lm81.c
rename {include => drivers/misc}/ds4510.h (75%)
delete mode 100644 drivers/rtc/rtc4543.c
delete mode 100644 drivers/twserial/Makefile
delete mode 100644 drivers/twserial/soft_tws.c
delete mode 100644 include/dtt.h
delete mode 100644 include/tws.hSignature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 1/47 configs: Re-sync
Run moveconfig.py -s to get defconfig files back in sync.
Signed-off-by Simon Glass <[email protected]>
---
configs/Sinovoip_BPI_M2_Plus_defconfig | 1 - configs/am335x_baltos_defconfig | 4 +- configs/am335x_evm_defconfig | 1 - configs/am335x_hs_evm_defconfig | 3 -- configs/am335x_igep003x_defconfig | 6 +-- configs/am335x_shc_defconfig | 4 +- configs/am335x_shc_ict_defconfig | 4 +- configs/am335x_shc_netboot_defconfig | 4 +- configs/am335x_shc_prompt_defconfig | 4 +- configs/am335x_shc_sdboot_defconfig | 4 +- configs/am335x_shc_sdboot_prompt_defconfig | 4 +- configs/am335x_sl50_defconfig | 4 +- configs/am43xx_evm_defconfig | 2 +- configs/am43xx_hs_evm_defconfig | 2 +- configs/am57xx_evm_defconfig | 4 +- configs/am57xx_hs_evm_defconfig | 4 +- configs/at91sam9263ek_norflash_boot_defconfig | 2 +- configs/at91sam9263ek_norflash_defconfig | 2 +- configs/birdland_bav335a_defconfig | 2 +- configs/birdland_bav335b_defconfig | 2 +- configs/brppt1_mmc_defconfig | 2 +- configs/brppt1_nand_defconfig | 2 +- configs/brppt1_spi_defconfig | 2 +- configs/brxre1_defconfig | 2 +- configs/chiliboard_defconfig | 4 +- configs/chromebook_minnie_defconfig | 2 +- configs/cm_fx6_defconfig | 2 +- configs/cm_t335_defconfig | 2 +- configs/cm_t43_defconfig | 2 +- configs/colibri_imx7_defconfig | 2 +- configs/colibri_vf_defconfig | 2 +- configs/comtrend_ar5387un_ram_defconfig | 65 ++++++++++------------- configs/comtrend_vr3032u_ram_defconfig | 66 ++++++++++------------- configs/dra7xx_evm_defconfig | 11 ++-- configs/dra7xx_hs_evm_defconfig | 8 ++- configs/evb-ast2500_defconfig | 12 ++--- configs/evb-rk3399_defconfig | 5 +- configs/firefly-rk3399_defconfig | 1 - configs/gwventana_emmc_defconfig | 2 +- configs/gwventana_gw5904_defconfig | 2 +- configs/gwventana_nand_defconfig | 2 +- configs/huawei_hg556a_ram_defconfig | 67 ++++++++++-------------- configs/imx6dl_icore_mmc_defconfig | 2 +- configs/imx6dl_icore_nand_defconfig | 2 +- configs/imx6q_icore_mmc_defconfig | 2 +- configs/imx6q_icore_nand_defconfig | 2 +- configs/k2e_evm_defconfig | 5 +- configs/k2e_hs_evm_defconfig | 3 +- configs/k2g_evm_defconfig | 4 +- configs/k2g_hs_evm_defconfig | 5 +- configs/k2hk_evm_defconfig | 4 +- configs/k2hk_hs_evm_defconfig | 3 +- configs/k2l_evm_defconfig | 4 +- configs/m53evk_defconfig | 2 +- configs/mvebu_db-88f7040-nand_defconfig | 7 ++- configs/mx51evk_defconfig | 2 +- configs/mx53cx9020_defconfig | 2 +- configs/mx53loco_defconfig | 2 +- configs/mx6cuboxi_defconfig | 2 +- configs/mx6sxsabresd_defconfig | 2 +- configs/mx6sxsabresd_spl_defconfig | 2 +- configs/mx7dsabresd_defconfig | 2 +- configs/mx7dsabresd_secure_defconfig | 2 +- configs/nanopi_neo_air_defconfig | 2 +- configs/nanopi_neo_defconfig | 2 +- configs/novena_defconfig | 2 +- configs/omap3_logic_defconfig | 1 - configs/opos6uldev_defconfig | 2 +- configs/orangepi_2_defconfig | 1 - configs/orangepi_lite_defconfig | 1 - configs/orangepi_one_defconfig | 1 - configs/orangepi_pc2_defconfig | 1 - configs/orangepi_pc_defconfig | 1 - configs/orangepi_pc_plus_defconfig | 1 - configs/orangepi_plus2e_defconfig | 1 - configs/orangepi_plus_defconfig | 1 - configs/orangepi_zero_defconfig | 2 +- configs/pcm051_rev1_defconfig | 2 +- configs/pcm051_rev3_defconfig | 2 +- configs/pengwyn_defconfig | 2 +- configs/pepper_defconfig | 2 +- configs/pine64_plus_defconfig | 1 - configs/pxm2_defconfig | 2 +- configs/rut_defconfig | 2 +- configs/sama5d2_xplained_mmc_defconfig | 4 +- configs/sama5d2_xplained_spiflash_defconfig | 2 +- configs/sandbox_defconfig | 8 +-- configs/sandbox_noblk_defconfig | 4 +- configs/sandbox_spl_defconfig | 4 +- configs/sfr_nb4-ser_ram_defconfig | 67 ++++++++++-------------- configs/stm32f746-disco_defconfig | 14 ++--- configs/tbs2910_defconfig | 2 +- configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig | 2 +- configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig | 2 +- configs/xilinx_zynqmp_zcu102_defconfig | 2 +- configs/xilinx_zynqmp_zcu102_revB_defconfig | 2 +- 96 files changed, 227 insertions(+), 307 deletions(-)
configs/Sinovoip_BPI_M2_Plus_defconfig +0 -1
@@ -8,7 +8,6 @@ CONFIG_MACPWR="PD6" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-bananapi-m2-plus" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_CONSOLE_MUX=y CONFIG_SPL=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set
configs/am335x_baltos_defconfig +2 -2
@@ -10,9 +10,8 @@ CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_NAND_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_SPL_FAT_SUPPORT=y CONFIG_FIT_VERBOSE=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="NAND"
@@ -24,6 +23,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_MTD_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
configs/am335x_evm_defconfig +0 -1
@@ -48,4 +48,3 @@ CONFIG_G_DNL_MANUFACTURER="Texas Instruments" CONFIG_G_DNL_VENDOR_NUM=0x0451 CONFIG_G_DNL_PRODUCT_NUM=0xd022 CONFIG_RSA=y -CONFIG_SPL_OF_LIBFDT=y
configs/am335x_hs_evm_defconfig +0 -3
@@ -17,7 +17,6 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_ARCH_MISC_INIT=y CONFIG_SPL=y -CONFIG_SPL_SYS_MALLOC_SIMPLE=y CONFIG_SPL_STACK_R=y # CONFIG_SPL_EXT_SUPPORT is not set CONFIG_SPL_MTD_SUPPORT=y
@@ -54,6 +53,4 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="Texas Instruments" CONFIG_G_DNL_VENDOR_NUM=0x0451 CONFIG_G_DNL_PRODUCT_NUM=0xd022 -CONFIG_USE_TINY_PRINTF=y CONFIG_RSA=y -CONFIG_SPL_OF_LIBFDT=y
configs/am335x_igep003x_defconfig +3 -3
@@ -3,17 +3,16 @@ CONFIG_ARCH_OMAP2PLUS=y CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_AM33XX=y CONFIG_SYS_MALLOC_F_LEN=0x2000 +CONFIG_AM33XX=y CONFIG_TARGET_AM335X_IGEP003X=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_NAND_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_SPL_FAT_SUPPORT=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="MACH_TYPE=MACH_TYPE_IGEP0033" CONFIG_SYS_CONSOLE_INFO_QUIET=y
@@ -23,6 +22,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_MTD_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
configs/am335x_shc_defconfig +2 -2
@@ -9,10 +9,9 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SPL_FAT_SUPPORT=y CONFIG_SERIES=y -CONFIG_SPL_POWER_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_SPL=y
@@ -20,6 +19,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="U-Boot# "
configs/am335x_shc_ict_defconfig +2 -2
@@ -9,11 +9,10 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SPL_FAT_SUPPORT=y CONFIG_SHC_ICT=y CONFIG_SERIES=y -CONFIG_SPL_POWER_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_SPL=y
@@ -21,6 +20,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_SYS_PROMPT="U-Boot# " CONFIG_AUTOBOOT_KEYED=y
configs/am335x_shc_netboot_defconfig +2 -2
@@ -9,11 +9,10 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SPL_FAT_SUPPORT=y CONFIG_SHC_NETBOOT=y CONFIG_SERIES=y -CONFIG_SPL_POWER_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_SPL=y
@@ -22,6 +21,7 @@ CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_SYS_PROMPT="U-Boot# " CONFIG_AUTOBOOT_KEYED=y
configs/am335x_shc_prompt_defconfig +2 -2
@@ -9,10 +9,9 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SPL_FAT_SUPPORT=y CONFIG_SERIES=y -CONFIG_SPL_POWER_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_SPL=y
@@ -20,6 +19,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Enter 'shc' to enter prompt (times out) %d \nEnter 'noautoboot' to enter prompt without timeout\n"
configs/am335x_shc_sdboot_defconfig +2 -2
@@ -9,11 +9,10 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SPL_FAT_SUPPORT=y CONFIG_SHC_SDBOOT=y CONFIG_SERIES=y -CONFIG_SPL_POWER_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_SPL=y
@@ -21,6 +20,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_SYS_PROMPT="U-Boot# " CONFIG_AUTOBOOT_KEYED=y
configs/am335x_shc_sdboot_prompt_defconfig +2 -2
@@ -9,11 +9,10 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y +CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SPL_FAT_SUPPORT=y CONFIG_SHC_SDBOOT=y CONFIG_SERIES=y -CONFIG_SPL_POWER_SUPPORT=y -CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_SPL=y
@@ -21,6 +20,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_SYS_PROMPT="U-Boot# " CONFIG_AUTOBOOT_KEYED=y
configs/am335x_sl50_defconfig +2 -2
@@ -9,9 +9,8 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_SPL_FAT_SUPPORT=y CONFIG_DISTRO_DEFAULTS=y CONFIG_SYS_EXTRA_OPTIONS="EMMC_BOOT" CONFIG_SYS_CONSOLE_INFO_QUIET=y
@@ -22,6 +21,7 @@ CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y # CONFIG_AUTOBOOT is not set # CONFIG_CMD_IMLS is not set
configs/am43xx_evm_defconfig +1 -1
@@ -1,8 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_AM43XX=y -CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_TARGET_AM43XX_EVM=y CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_DEFAULT_DEVICE_TREE="am437x-gp-evm"
configs/am43xx_hs_evm_defconfig +1 -1
@@ -1,8 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_AM43XX=y -CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_TI_SECURE_DEVICE=y CONFIG_TARGET_AM43XX_EVM=y CONFIG_ISW_ENTRY_ADDR=0x403018e0
configs/am57xx_evm_defconfig +2 -2
@@ -1,14 +1,14 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_OMAP54XX=y -CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_TARGET_AM57XX_EVM=y # CONFIG_SPL_NAND_SUPPORT is not set CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y -CONFIG_ARMV7_LPAE=y CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_ARMV7_LPAE=y CONFIG_DEFAULT_DEVICE_TREE="am572x-idk" CONFIG_SPL_LOAD_FIT=y CONFIG_OF_BOARD_SETUP=y
configs/am57xx_hs_evm_defconfig +2 -2
@@ -1,8 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_OMAP54XX=y -CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_TI_SECURE_DEVICE=y CONFIG_TARGET_AM57XX_EVM=y CONFIG_TI_SECURE_EMIF_REGION_START=0xbdb00000
@@ -11,8 +11,8 @@ CONFIG_TI_SECURE_EMIF_PROTECTED_REGION_SIZE=0x01c00000 # CONFIG_SPL_NAND_SUPPORT is not set CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y -CONFIG_ARMV7_LPAE=y CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_ARMV7_LPAE=y CONFIG_DEFAULT_DEVICE_TREE="am57xx-beagle-x15" CONFIG_FIT_IMAGE_POST_PROCESS=y CONFIG_SPL_LOAD_FIT=y
configs/at91sam9263ek_norflash_boot_defconfig +1 -1
@@ -31,6 +31,7 @@ CONFIG_DM_GPIO=y CONFIG_AT91_GPIO=y CONFIG_DM_MMC=y CONFIG_GENERIC_ATMEL_MCI=y +CONFIG_MTD_NOR_FLASH=y CONFIG_DM_ETH=y CONFIG_MACB=y CONFIG_PINCTRL=y
@@ -43,7 +44,6 @@ CONFIG_DEBUG_UART_CLOCK=100000000 CONFIG_DEBUG_UART_BOARD_INIT=y CONFIG_DEBUG_UART_ANNOUNCE=y CONFIG_ATMEL_USART=y -CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_STORAGE=y
configs/at91sam9263ek_norflash_defconfig +1 -1
@@ -31,6 +31,7 @@ CONFIG_DM_GPIO=y CONFIG_AT91_GPIO=y CONFIG_DM_MMC=y CONFIG_GENERIC_ATMEL_MCI=y +CONFIG_MTD_NOR_FLASH=y CONFIG_DM_ETH=y CONFIG_MACB=y CONFIG_PINCTRL=y
@@ -43,7 +44,6 @@ CONFIG_DEBUG_UART_CLOCK=100000000 CONFIG_DEBUG_UART_BOARD_INIT=y CONFIG_DEBUG_UART_ANNOUNCE=y CONFIG_ATMEL_USART=y -CONFIG_MTD_NOR_FLASH=y CONFIG_USB=y CONFIG_DM_USB=y CONFIG_USB_STORAGE=y
configs/birdland_bav335a_defconfig +1 -1
@@ -10,7 +10,6 @@ CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_BAV_VERSION=1 CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1" CONFIG_SYS_CONSOLE_INFO_QUIET=y
@@ -21,6 +20,7 @@ CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_MUSB_NEW_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
configs/birdland_bav335b_defconfig +1 -1
@@ -10,7 +10,6 @@ CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_BAV_VERSION=2 CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1" CONFIG_SYS_CONSOLE_INFO_QUIET=y
@@ -21,6 +20,7 @@ CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_MUSB_NEW_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
configs/brppt1_mmc_defconfig +1 -1
@@ -7,7 +7,6 @@ CONFIG_TARGET_BRPPT1=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,EMMC_BOOT" CONFIG_BOOTDELAY=-2
@@ -23,6 +22,7 @@ CONFIG_SPL=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
configs/brppt1_nand_defconfig +1 -1
@@ -7,7 +7,6 @@ CONFIG_TARGET_BRPPT1=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_NAND_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,NAND" CONFIG_BOOTDELAY=-2
@@ -23,6 +22,7 @@ CONFIG_SPL=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
configs/brppt1_spi_defconfig +1 -1
@@ -9,7 +9,6 @@ CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1,SPI_BOOT,EMMC_BOOT" CONFIG_SPI_BOOT=y
@@ -26,6 +25,7 @@ CONFIG_SPL=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
configs/brxre1_defconfig +1 -1
@@ -5,7 +5,6 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SYS_EXTRA_OPTIONS="SERIAL1,CONS_INDEX=1" CONFIG_BOOTDELAY=-2 # CONFIG_CONSOLE_MUX is not set
@@ -20,6 +19,7 @@ CONFIG_SPL=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300 CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y # CONFIG_CMD_BOOTD is not set
configs/chiliboard_defconfig +2 -2
@@ -9,14 +9,14 @@ CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_NAND_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_SPL_FAT_SUPPORT=y CONFIG_BOOTDELAY=1 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_SPL=y CONFIG_SPL_STACK_R=y CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set
configs/chromebook_minnie_defconfig +1 -1
@@ -72,8 +72,8 @@ CONFIG_SYSRESET=y CONFIG_DM_VIDEO=y CONFIG_DISPLAY=y CONFIG_VIDEO_ROCKCHIP=y -CONFIG_DISPLAY_ROCKCHIP_HDMI=y CONFIG_DISPLAY_ROCKCHIP_EDP=y +CONFIG_DISPLAY_ROCKCHIP_HDMI=y CONFIG_CONSOLE_SCROLL_LINES=10 CONFIG_USE_TINY_PRINTF=y CONFIG_CMD_DHRYSTONE=y
configs/cm_fx6_defconfig +1 -1
@@ -9,8 +9,8 @@ CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,MX6QDL,SPL" CONFIG_BOOTDELAY=3
configs/cm_t335_defconfig +1 -1
@@ -11,13 +11,13 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_NAND_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_SPL=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_MTD_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="CM-T335 # " CONFIG_CMD_BOOTZ=y
configs/cm_t43_defconfig +1 -1
@@ -10,7 +10,6 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y # CONFIG_DISPLAY_CPUINFO is not set
@@ -21,6 +20,7 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x480 CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_MTD_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="CM-T43 # " CONFIG_CMD_BOOTZ=y
configs/colibri_imx7_defconfig +1 -1
@@ -2,9 +2,9 @@ CONFIG_ARM=y CONFIG_SYS_THUMB_BUILD=y CONFIG_ARCH_MX7=y CONFIG_TARGET_COLIBRI_IMX7=y +CONFIG_VIDEO=y CONFIG_IMX_RDC=y CONFIG_IMX_BOOTAUX=y -CONFIG_VIDEO=y CONFIG_DEFAULT_DEVICE_TREE="imx7-colibri" CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/toradex/colibri_imx7/imximage.cfg,MX7D" CONFIG_BOOTDELAY=1
configs/colibri_vf_defconfig +1 -1
@@ -1,8 +1,8 @@ CONFIG_ARM=y CONFIG_SYS_THUMB_BUILD=y CONFIG_ARCH_VF610=y -CONFIG_TARGET_COLIBRI_VF=y CONFIG_VIDEO=y +CONFIG_TARGET_COLIBRI_VF=y CONFIG_DEFAULT_DEVICE_TREE="vf610-colibri" CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/toradex/colibri_vf/imximage.cfg,ENV_IS_IN_NAND,IMX_NAND" CONFIG_BOOTDELAY=1
configs/comtrend_ar5387un_ram_defconfig +27 -38
81 lines not on this page · raw message
configs/comtrend_vr3032u_ram_defconfig +28 -38
82 lines not on this page · raw message
configs/dra7xx_evm_defconfig +4 -7
@@ -1,14 +1,14 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_OMAP54XX=y -CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_TARGET_DRA7XX_EVM=y # CONFIG_SPL_NAND_SUPPORT is not set CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y -CONFIG_ARMV7_LPAE=y CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_ARMV7_LPAE=y CONFIG_DEFAULT_DEVICE_TREE="dra7-evm" CONFIG_SPL_LOAD_FIT=y CONFIG_OF_BOARD_SETUP=y
@@ -43,10 +43,9 @@ CONFIG_REGMAP=y CONFIG_SPL_REGMAP=y CONFIG_SYSCON=y CONFIG_SPL_SYSCON=y -CONFIG_BLK=y +CONFIG_SPL_OF_TRANSLATE=y CONFIG_DM_SCSI=y CONFIG_DWC_AHCI=y -CONFIG_SPL_OF_TRANSLATE=y CONFIG_DFU_MMC=y CONFIG_DFU_RAM=y CONFIG_DFU_SF=y
@@ -61,6 +60,7 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_DM_ETH=y +CONFIG_SPL_PHY=y CONFIG_DM_PMIC=y CONFIG_PMIC_PALMAS=y CONFIG_PMIC_LP873X=y
@@ -90,6 +90,3 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="Texas Instruments" CONFIG_G_DNL_VENDOR_NUM=0x0451 CONFIG_G_DNL_PRODUCT_NUM=0xd022 -CONFIG_SPL_PHY=y -CONFIG_PIPE3_PHY=y -CONFIG_SPL_PIPE3_PHY=y
configs/dra7xx_hs_evm_defconfig +3 -5
@@ -1,8 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_OMAP2PLUS=y +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_OMAP54XX=y -CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_TI_SECURE_DEVICE=y CONFIG_TARGET_DRA7XX_EVM=y CONFIG_TI_SECURE_EMIF_REGION_START=0xbdb00000
@@ -11,8 +11,8 @@ CONFIG_TI_SECURE_EMIF_PROTECTED_REGION_SIZE=0x01c00000 # CONFIG_SPL_NAND_SUPPORT is not set CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y -CONFIG_ARMV7_LPAE=y CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_ARMV7_LPAE=y CONFIG_DEFAULT_DEVICE_TREE="dra7-evm" CONFIG_FIT_IMAGE_POST_PROCESS=y CONFIG_SPL_LOAD_FIT=y
@@ -63,6 +63,7 @@ CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_BAR=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_DM_ETH=y +CONFIG_SPL_PHY=y CONFIG_DM_PMIC=y CONFIG_PMIC_PALMAS=y CONFIG_PMIC_LP873X=y
@@ -92,6 +93,3 @@ CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_G_DNL_MANUFACTURER="Texas Instruments" CONFIG_G_DNL_VENDOR_NUM=0x0451 CONFIG_G_DNL_PRODUCT_NUM=0xd022 -CONFIG_SPL_PHY=y -CONFIG_PIPE3_PHY=y -CONFIG_SPL_PIPE3_PHY=y
configs/evb-ast2500_defconfig +6 -6
@@ -3,21 +3,21 @@ CONFIG_ARCH_ASPEED=y CONFIG_ASPEED_AST2500=y CONFIG_TARGET_EVB_AST2500=y CONFIG_SYS_MALLOC_F_LEN=0x2000 -CONFIG_PRE_CONSOLE_BUFFER=y CONFIG_DEFAULT_DEVICE_TREE="ast2500-evb" +CONFIG_PRE_CONSOLE_BUFFER=y CONFIG_PRE_CON_BUF_ADDR=0x1e720000 # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_CMD_IMLS is not set +CONFIG_CMD_I2C=y CONFIG_REGMAP=y CONFIG_CLK=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_ASPEED=y +CONFIG_PINCTRL=y CONFIG_RAM=y +CONFIG_DM_RESET=y CONFIG_DM_SERIAL=y CONFIG_SYS_NS16550=y CONFIG_SYSRESET=y CONFIG_TIMER=y CONFIG_WDT=y -CONFIG_DM_RESET=y -CONFIG_PINCTRL=y -CONFIG_DM_I2C=y -CONFIG_SYS_I2C_ASPEED=y -CONFIG_CMD_I2C=y
configs/evb-rk3399_defconfig +1 -4
@@ -23,6 +23,7 @@ CONFIG_CMD_TIME=y CONFIG_SPL_OF_CONTROL=y CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents" CONFIG_SPL_OF_PLATDATA=y +CONFIG_NET_RANDOM_ETHADDR=y CONFIG_REGMAP=y CONFIG_SPL_REGMAP=y CONFIG_SYSCON=y
@@ -34,12 +35,8 @@ CONFIG_SYS_I2C_ROCKCHIP=y CONFIG_MMC_DW=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_ROCKCHIP=y -CONFIG_DM_PMIC=y -CONFIG_PMIC_RK808=y -CONFIG_REGULATOR_RK808=y CONFIG_DM_ETH=y CONFIG_ETH_DESIGNWARE=y -CONFIG_NET_RANDOM_ETHADDR=y CONFIG_GMAC_ROCKCHIP=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y
configs/firefly-rk3399_defconfig +0 -1
@@ -39,7 +39,6 @@ CONFIG_ETH_DESIGNWARE=y CONFIG_GMAC_ROCKCHIP=y CONFIG_PINCTRL=y CONFIG_SPL_PINCTRL=y -CONFIG_ROCKCHIP_RK3399_PINCTRL=y CONFIG_DM_PMIC=y CONFIG_PMIC_RK8XX=y CONFIG_REGULATOR_PWM=y
configs/gwventana_emmc_defconfig +1 -1
@@ -7,7 +7,6 @@ CONFIG_TARGET_GW_VENTANA=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_VIDEO=y CONFIG_SPL_STACK_R_ADDR=0x18000000 CONFIG_FIT=y
@@ -23,6 +22,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_DMA_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Ventana > " CONFIG_CMD_BOOTZ=y
configs/gwventana_gw5904_defconfig +1 -1
@@ -7,7 +7,6 @@ CONFIG_TARGET_GW_VENTANA=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_VIDEO=y CONFIG_SPL_STACK_R_ADDR=0x18000000 CONFIG_FIT=y
@@ -23,6 +22,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_DMA_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Ventana > " CONFIG_CMD_BOOTZ=y
configs/gwventana_nand_defconfig +1 -1
@@ -8,7 +8,6 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_NAND_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_VIDEO=y CONFIG_SPL_STACK_R_ADDR=0x18000000 CONFIG_FIT=y
@@ -24,6 +23,7 @@ CONFIG_SPL_STACK_R=y CONFIG_SPL_DMA_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Ventana > " CONFIG_CMD_BOOTZ=y
configs/huawei_hg556a_ram_defconfig +28 -39
83 lines not on this page · raw message
configs/imx6dl_icore_mmc_defconfig +1 -1
@@ -7,8 +7,8 @@ CONFIG_TARGET_MX6Q_ICORE=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore" CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y
configs/imx6dl_icore_nand_defconfig +1 -1
@@ -6,8 +6,8 @@ CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_TARGET_MX6Q_ICORE=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_DEFAULT_DEVICE_TREE="imx6dl-icore" CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y
configs/imx6q_icore_mmc_defconfig +1 -1
@@ -7,8 +7,8 @@ CONFIG_TARGET_MX6Q_ICORE=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_DEFAULT_DEVICE_TREE="imx6q-icore" CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y
configs/imx6q_icore_nand_defconfig +1 -1
@@ -6,8 +6,8 @@ CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_TARGET_MX6Q_ICORE=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_DEFAULT_DEVICE_TREE="imx6q-icore" CONFIG_FIT=y CONFIG_FIT_SIGNATURE=y
configs/k2e_evm_defconfig +2 -3
@@ -1,14 +1,13 @@ CONFIG_ARM=y CONFIG_ARCH_KEYSTONE=y CONFIG_SYS_TEXT_BASE=0x0c000000 +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_TARGET_K2E_EVM=y -CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_DEFAULT_DEVICE_TREE="keystone-k2e-evm" CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
@@ -16,8 +15,8 @@ CONFIG_VERSION_VARIABLE=y CONFIG_BOARD_EARLY_INIT_F=y CONFIG_SPL=y CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y -CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set # CONFIG_CMD_GPT is not set
configs/k2e_hs_evm_defconfig +1 -2
@@ -1,9 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_KEYSTONE=y CONFIG_SYS_TEXT_BASE=0x0c000060 -CONFIG_TARGET_K2E_EVM=y CONFIG_TI_COMMON_CMD_OPTIONS=y -CONFIG_TI_SECURE_DEVICE=y +CONFIG_TARGET_K2E_EVM=y CONFIG_DEFAULT_DEVICE_TREE="keystone-k2e-evm" CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/k2g_evm_defconfig +2 -2
@@ -1,14 +1,13 @@ CONFIG_ARM=y CONFIG_ARCH_KEYSTONE=y CONFIG_SYS_TEXT_BASE=0x0c000000 +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_TARGET_K2G_EVM=y -CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_DEFAULT_DEVICE_TREE="keystone-k2g-evm" CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
@@ -16,6 +15,7 @@ CONFIG_VERSION_VARIABLE=y CONFIG_BOARD_EARLY_INIT_F=y CONFIG_SPL=y CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set
configs/k2g_hs_evm_defconfig +1 -4
@@ -1,12 +1,9 @@ CONFIG_ARM=y CONFIG_ARCH_KEYSTONE=y CONFIG_SYS_TEXT_BASE=0x0c000060 -CONFIG_TARGET_K2G_EVM=y CONFIG_TI_COMMON_CMD_OPTIONS=y -CONFIG_TI_SECURE_DEVICE=y +CONFIG_TARGET_K2G_EVM=y CONFIG_DEFAULT_DEVICE_TREE="keystone-k2g-evm" -CONFIG_FIT=y -CONFIG_FIT_IMAGE_POST_PROCESS=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y
configs/k2hk_evm_defconfig +2 -2
@@ -1,14 +1,13 @@ CONFIG_ARM=y CONFIG_ARCH_KEYSTONE=y CONFIG_SYS_TEXT_BASE=0x0c000000 +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_TARGET_K2HK_EVM=y -CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_DEFAULT_DEVICE_TREE="keystone-k2hk-evm" CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
@@ -16,6 +15,7 @@ CONFIG_VERSION_VARIABLE=y CONFIG_BOARD_EARLY_INIT_F=y CONFIG_SPL=y CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set
configs/k2hk_hs_evm_defconfig +1 -2
@@ -1,9 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_KEYSTONE=y CONFIG_SYS_TEXT_BASE=0x0c000060 -CONFIG_TARGET_K2HK_EVM=y CONFIG_TI_COMMON_CMD_OPTIONS=y -CONFIG_TI_SECURE_DEVICE=y +CONFIG_TARGET_K2HK_EVM=y CONFIG_DEFAULT_DEVICE_TREE="keystone-k2hk-evm" CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/k2l_evm_defconfig +2 -2
@@ -1,14 +1,13 @@ CONFIG_ARM=y CONFIG_ARCH_KEYSTONE=y CONFIG_SYS_TEXT_BASE=0x0c000000 +CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_TARGET_K2L_EVM=y -CONFIG_TI_COMMON_CMD_OPTIONS=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_DEFAULT_DEVICE_TREE="keystone-k2l-evm" CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_CONSOLE_INFO_QUIET=y
@@ -16,6 +15,7 @@ CONFIG_VERSION_VARIABLE=y CONFIG_BOARD_EARLY_INIT_F=y CONFIG_SPL=y CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set
configs/m53evk_defconfig +1 -1
@@ -6,8 +6,8 @@ CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_TARGET_M53EVK=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_NAND_SUPPORT=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_FIT=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/aries/m53evk/imximage.cfg" CONFIG_BOOTDELAY=3
configs/mvebu_db-88f7040-nand_defconfig +3 -4
@@ -7,7 +7,6 @@ CONFIG_SMBIOS_PRODUCT_NAME="" CONFIG_AHCI=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SYS_CONSOLE_INFO_QUIET=y -CONFIG_BOARD_LATE_INIT=y # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_ARCH_EARLY_INIT_R=y
@@ -16,12 +15,12 @@ CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y +CONFIG_CMD_NAND=y CONFIG_CMD_PART=y CONFIG_CMD_SF=y CONFIG_CMD_SPI=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y -CONFIG_CMD_NAND=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_TFTPPUT=y
@@ -31,6 +30,7 @@ CONFIG_CMD_PING=y CONFIG_CMD_CACHE=y CONFIG_CMD_TIME=y CONFIG_CMD_MVEBU_BUBT=y +CONFIG_MVEBU_NAND_BOOT=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_FAT=y
@@ -45,12 +45,11 @@ CONFIG_MISC=y CONFIG_DM_MMC=y CONFIG_MMC_SDHCI=y CONFIG_MMC_SDHCI_XENON=y +CONFIG_NAND_PXA3XX=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_MACRONIX=y CONFIG_SPI_FLASH_SPANSION=y CONFIG_SPI_FLASH_STMICRO=y -CONFIG_MVEBU_NAND_BOOT=y -CONFIG_NAND_PXA3XX=y CONFIG_PHYLIB=y CONFIG_PCI=y CONFIG_DM_PCI=y
configs/mx51evk_defconfig +1 -1
@@ -1,8 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_MX5=y CONFIG_TARGET_MX51EVK=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx51evk/imximage.cfg" CONFIG_BOOTDELAY=1 # CONFIG_CONSOLE_MUX is not set
configs/mx53cx9020_defconfig +1 -1
@@ -1,8 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_MX5=y CONFIG_TARGET_MX53CX9020=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_DEFAULT_DEVICE_TREE="imx53-cx9020" CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/beckhoff/mx53cx9020/imximage.cfg" CONFIG_BOOTDELAY=1
configs/mx53loco_defconfig +1 -1
@@ -1,8 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_MX5=y CONFIG_TARGET_MX53LOCO=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx53loco/imximage.cfg" CONFIG_BOOTDELAY=1 # CONFIG_CONSOLE_MUX is not set
configs/mx6cuboxi_defconfig +1 -1
@@ -8,8 +8,8 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_DISTRO_DEFAULTS=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,MX6QDL" # CONFIG_SYS_STDIO_DEREGISTER is not set
configs/mx6sxsabresd_defconfig +1 -1
@@ -1,8 +1,8 @@ CONFIG_ARM=y CONFIG_ARCH_MX6=y CONFIG_TARGET_MX6SXSABRESD=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6sxsabresd/imximage.cfg" CONFIG_BOOTDELAY=3 # CONFIG_CONSOLE_MUX is not set
configs/mx6sxsabresd_spl_defconfig +1 -1
@@ -8,8 +8,8 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg" CONFIG_BOOTDELAY=3 # CONFIG_CONSOLE_MUX is not set
configs/mx7dsabresd_defconfig +1 -1
@@ -1,11 +1,11 @@ CONFIG_ARM=y CONFIG_ARCH_MX7=y CONFIG_TARGET_MX7DSABRESD=y +CONFIG_VIDEO=y # CONFIG_ARMV7_VIRT is not set CONFIG_IMX_RDC=y CONFIG_IMX_BOOTAUX=y # CONFIG_CMD_BMODE is not set -CONFIG_VIDEO=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7dsabresd/imximage.cfg" CONFIG_BOOTDELAY=3 # CONFIG_CONSOLE_MUX is not set
configs/mx7dsabresd_secure_defconfig +1 -1
@@ -1,11 +1,11 @@ CONFIG_ARM=y CONFIG_ARCH_MX7=y CONFIG_TARGET_MX7DSABRESD=y +CONFIG_VIDEO=y CONFIG_ARMV7_BOOT_SEC_DEFAULT=y CONFIG_IMX_RDC=y CONFIG_IMX_BOOTAUX=y # CONFIG_CMD_BMODE is not set -CONFIG_VIDEO=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx7dsabresd/imximage.cfg" CONFIG_BOOTDELAY=3 # CONFIG_CONSOLE_MUX is not set
configs/nanopi_neo_air_defconfig +1 -1
@@ -4,6 +4,7 @@ CONFIG_MACH_SUN8I_H3=y CONFIG_DRAM_CLK=408 CONFIG_DRAM_ZQ=3881979 CONFIG_DRAM_ODT_EN=y +# CONFIG_VIDEO_DE2 is not set CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-neo-air" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_CONSOLE_MUX=y
@@ -15,4 +16,3 @@ CONFIG_SPL=y # CONFIG_SPL_ISO_PARTITION is not set # CONFIG_SPL_EFI_PARTITION is not set CONFIG_USB_EHCI_HCD=y -# CONFIG_VIDEO_DE2 is not set
configs/nanopi_neo_defconfig +1 -1
@@ -4,6 +4,7 @@ CONFIG_MACH_SUN8I_H3=y CONFIG_DRAM_CLK=408 CONFIG_DRAM_ZQ=3881979 CONFIG_DRAM_ODT_EN=y +# CONFIG_VIDEO_DE2 is not set CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-nanopi-neo" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_CONSOLE_MUX=y
@@ -16,4 +17,3 @@ CONFIG_SPL=y # CONFIG_SPL_EFI_PARTITION is not set CONFIG_SUN8I_EMAC=y CONFIG_USB_EHCI_HCD=y -# CONFIG_VIDEO_DE2 is not set
configs/novena_defconfig +1 -1
@@ -9,8 +9,8 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_FAT_SUPPORT=y CONFIG_VIDEO=y +CONFIG_SPL_FAT_SUPPORT=y CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/imx-common/spl_sd.cfg,MX6Q"
configs/omap3_logic_defconfig +0 -1
@@ -5,7 +5,6 @@ CONFIG_OMAP34XX=y CONFIG_TARGET_OMAP3_LOGIC=y CONFIG_SPL_STACK_R_ADDR=0x82000000 CONFIG_DEFAULT_DEVICE_TREE="logicpd-torpedo-37xx-devkit" -CONFIG_FIT=y CONFIG_SYS_EXTRA_OPTIONS="NAND" CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y
configs/opos6uldev_defconfig +1 -1
@@ -7,8 +7,8 @@ CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -# CONFIG_CMD_BMODE is not set CONFIG_VIDEO=y +# CONFIG_CMD_BMODE is not set CONFIG_DEFAULT_DEVICE_TREE="imx6ul-opos6uldev" CONFIG_BOOTDELAY=5 # CONFIG_CONSOLE_MUX is not set
configs/orangepi_2_defconfig +0 -1
@@ -8,7 +8,6 @@ CONFIG_DRAM_ODT_EN=y CONFIG_USB1_VBUS_PIN="PG13" CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-2" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_CONSOLE_MUX=y CONFIG_SPL=y CONFIG_SPL_I2C_SUPPORT=y # CONFIG_CMD_IMLS is not set
configs/orangepi_lite_defconfig +0 -1
@@ -6,7 +6,6 @@ CONFIG_DRAM_ZQ=3881979 CONFIG_DRAM_ODT_EN=y CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-lite" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_CONSOLE_MUX=y CONFIG_SPL=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set
configs/orangepi_one_defconfig +0 -1
@@ -6,7 +6,6 @@ CONFIG_DRAM_ZQ=3881979 CONFIG_DRAM_ODT_EN=y CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-one" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_CONSOLE_MUX=y CONFIG_SPL=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set
configs/orangepi_pc2_defconfig +0 -1
@@ -6,7 +6,6 @@ CONFIG_DRAM_CLK=672 CONFIG_DRAM_ZQ=3881977 CONFIG_DEFAULT_DEVICE_TREE="sun50i-h5-orangepi-pc2" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_CONSOLE_MUX=y CONFIG_SPL=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set
configs/orangepi_pc_defconfig +0 -1
@@ -6,7 +6,6 @@ CONFIG_DRAM_ZQ=3881979 CONFIG_DRAM_ODT_EN=y CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-pc" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_CONSOLE_MUX=y CONFIG_SPL=y CONFIG_SPL_I2C_SUPPORT=y # CONFIG_CMD_IMLS is not set
configs/orangepi_pc_plus_defconfig +0 -1
@@ -7,7 +7,6 @@ CONFIG_DRAM_ODT_EN=y CONFIG_MMC_SUNXI_SLOT_EXTRA=2 CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-pc-plus" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_CONSOLE_MUX=y CONFIG_SPL=y CONFIG_SPL_I2C_SUPPORT=y # CONFIG_CMD_IMLS is not set
configs/orangepi_plus2e_defconfig +0 -1
@@ -8,7 +8,6 @@ CONFIG_MACPWR="PD6" CONFIG_MMC_SUNXI_SLOT_EXTRA=2 CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-plus2e" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_CONSOLE_MUX=y CONFIG_SPL=y CONFIG_SPL_I2C_SUPPORT=y # CONFIG_CMD_IMLS is not set
configs/orangepi_plus_defconfig +0 -1
@@ -10,7 +10,6 @@ CONFIG_USB1_VBUS_PIN="PG13" CONFIG_SATAPWR="PG11" CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-plus" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_CONSOLE_MUX=y CONFIG_SPL=y CONFIG_SPL_I2C_SUPPORT=y # CONFIG_CMD_IMLS is not set
configs/orangepi_zero_defconfig +1 -1
@@ -5,6 +5,7 @@ CONFIG_MACH_SUN8I_H3=y CONFIG_DRAM_CLK=672 CONFIG_DRAM_ZQ=3881979 CONFIG_DRAM_ODT_EN=y +# CONFIG_VIDEO_DE2 is not set CONFIG_DEFAULT_DEVICE_TREE="sun8i-h2-plus-orangepi-zero" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_CONSOLE_MUX=y
@@ -15,4 +16,3 @@ CONFIG_SPL=y CONFIG_SPL_SPI_SUNXI=y CONFIG_SUN8I_EMAC=y CONFIG_USB_EHCI_HCD=y -# CONFIG_VIDEO_DE2 is not set
configs/pcm051_rev1_defconfig +1 -1
@@ -10,7 +10,6 @@ CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SYS_EXTRA_OPTIONS="REV1" CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y
@@ -23,6 +22,7 @@ CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_NET_SUPPORT=y CONFIG_SPL_NET_VCI_STRING="pcm051 U-Boot SPL" CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
configs/pcm051_rev3_defconfig +1 -1
@@ -10,7 +10,6 @@ CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SYS_EXTRA_OPTIONS="REV3" CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y
@@ -23,6 +22,7 @@ CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_NET_SUPPORT=y CONFIG_SPL_NET_VCI_STRING="pcm051 U-Boot SPL" CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
configs/pengwyn_defconfig +1 -1
@@ -11,7 +11,6 @@ CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_NAND_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_ARCH_MISC_INIT=y
@@ -24,6 +23,7 @@ CONFIG_SPL_MTD_SUPPORT=y CONFIG_SPL_NET_SUPPORT=y CONFIG_SPL_NET_VCI_STRING="AM335x U-Boot SPL" CONFIG_SPL_OS_BOOT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y
configs/pepper_defconfig +1 -1
@@ -10,12 +10,12 @@ CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SPL_POWER_SUPPORT=y CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_SPL=y CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y +CONFIG_SPL_POWER_SUPPORT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="pepper# " CONFIG_CMD_BOOTZ=y
configs/pine64_plus_defconfig +0 -1
@@ -4,7 +4,6 @@ CONFIG_MACH_SUN50I=y CONFIG_RESERVE_ALLWINNER_BOOT0_HEADER=y CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-pine64-plus" # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_CONSOLE_MUX=y CONFIG_SPL=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_FLASH is not set
configs/pxm2_defconfig +1 -1
@@ -13,8 +13,8 @@ CONFIG_SPL_NAND_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_FAT_SUPPORT=y CONFIG_VIDEO=y +CONFIG_SPL_FAT_SUPPORT=y CONFIG_DEFAULT_DEVICE_TREE="am335x-pxm50" CONFIG_BOOTDELAY=3 # CONFIG_CONSOLE_MUX is not set
configs/rut_defconfig +1 -1
@@ -13,8 +13,8 @@ CONFIG_SPL_NAND_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y -CONFIG_SPL_FAT_SUPPORT=y CONFIG_VIDEO=y +CONFIG_SPL_FAT_SUPPORT=y CONFIG_DEFAULT_DEVICE_TREE="am335x-rut" CONFIG_BOOTDELAY=3 # CONFIG_CONSOLE_MUX is not set
configs/sama5d2_xplained_mmc_defconfig +2 -2
@@ -4,12 +4,12 @@ CONFIG_TARGET_SAMA5D2_XPLAINED=y CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y CONFIG_SPL_LIBDISK_SUPPORT=y CONFIG_SPL_FAT_SUPPORT=y -CONFIG_SYS_MALLOC_F_LEN=0x2000 -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d2_xplained" CONFIG_FIT=y CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_MMC"
configs/sama5d2_xplained_spiflash_defconfig +1 -1
@@ -6,9 +6,9 @@ CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_SYS_MALLOC_F_LEN=0x2000 CONFIG_SPL_SERIAL_SUPPORT=y +CONFIG_SPL_DRIVERS_MISC_SUPPORT=y CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y -CONFIG_SPL_DRIVERS_MISC_SUPPORT=y CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d2_xplained" CONFIG_FIT=y CONFIG_SYS_EXTRA_OPTIONS="SAMA5D2,SYS_USE_SERIALFLASH"
configs/sandbox_defconfig +4 -4
@@ -115,6 +115,8 @@ CONFIG_PCI=y CONFIG_DM_PCI=y CONFIG_DM_PCI_COMPAT=y CONFIG_PCI_SANDBOX=y +CONFIG_PHY=y +CONFIG_PHY_SANDBOX=y CONFIG_PINCTRL=y CONFIG_PINCONF=y CONFIG_PINCTRL_ROCKCHIP_RK3036=y
@@ -170,10 +172,10 @@ CONFIG_CONSOLE_ROTATION=y CONFIG_CONSOLE_TRUETYPE=y CONFIG_CONSOLE_TRUETYPE_CANTORAONE=y CONFIG_VIDEO_SANDBOX_SDL=y +CONFIG_WDT=y +CONFIG_WDT_SANDBOX=y CONFIG_FS_CBFS=y CONFIG_FS_CRAMFS=y -CONFIG_PHY=y -CONFIG_PHY_SANDBOX=y CONFIG_CMD_DHRYSTONE=y CONFIG_TPM=y CONFIG_LZ4=y
@@ -182,5 +184,3 @@ CONFIG_UNIT_TEST=y CONFIG_UT_TIME=y CONFIG_UT_DM=y CONFIG_UT_ENV=y -CONFIG_WDT=y -CONFIG_WDT_SANDBOX=y
configs/sandbox_noblk_defconfig +2 -2
@@ -121,6 +121,8 @@ CONFIG_PCI=y CONFIG_DM_PCI=y CONFIG_DM_PCI_COMPAT=y CONFIG_PCI_SANDBOX=y +CONFIG_PHY=y +CONFIG_PHY_SANDBOX=y CONFIG_PINCTRL=y CONFIG_PINCONF=y CONFIG_PINCTRL_ROCKCHIP_RK3036=y
@@ -174,8 +176,6 @@ CONFIG_CONSOLE_TRUETYPE_CANTORAONE=y CONFIG_VIDEO_SANDBOX_SDL=y CONFIG_FS_CBFS=y CONFIG_FS_CRAMFS=y -CONFIG_PHY=y -CONFIG_PHY_SANDBOX=y CONFIG_CMD_DHRYSTONE=y CONFIG_TPM=y CONFIG_LZ4=y
configs/sandbox_spl_defconfig +2 -2
@@ -125,6 +125,8 @@ CONFIG_PCI=y CONFIG_DM_PCI=y CONFIG_DM_PCI_COMPAT=y CONFIG_PCI_SANDBOX=y +CONFIG_PHY=y +CONFIG_PHY_SANDBOX=y CONFIG_PINCTRL=y CONFIG_PINCONF=y CONFIG_PINCTRL_SANDBOX=y
@@ -178,8 +180,6 @@ CONFIG_CONSOLE_TRUETYPE_CANTORAONE=y CONFIG_VIDEO_SANDBOX_SDL=y CONFIG_FS_CBFS=y CONFIG_FS_CRAMFS=y -CONFIG_PHY=y -CONFIG_PHY_SANDBOX=y CONFIG_CMD_DHRYSTONE=y CONFIG_TPM=y CONFIG_LZ4=y
configs/sfr_nb4-ser_ram_defconfig +28 -39
84 lines not on this page · raw message
configs/stm32f746-disco_defconfig +4 -10
@@ -1,5 +1,6 @@ CONFIG_ARM=y CONFIG_STM32=y +CONFIG_SYS_MALLOC_F_LEN=0xC00 CONFIG_STM32F7=y CONFIG_TARGET_STM32F746_DISCO=y CONFIG_DEFAULT_DEVICE_TREE="stm32f746-disco"
@@ -24,10 +25,10 @@ CONFIG_CMD_DNS=y CONFIG_CMD_LINK_LOCAL=y CONFIG_CMD_TIMER=y CONFIG_OF_CONTROL=y -CONFIG_DM_SEQ_ALIAS=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_NETCONSOLE=y CONFIG_CLK=y +CONFIG_DM_GPIO=y # CONFIG_MMC is not set CONFIG_MTD=y CONFIG_MTD_NOR_FLASH=y
@@ -39,17 +40,10 @@ CONFIG_ETH_DESIGNWARE=y CONFIG_PINCTRL=y # CONFIG_PINCTRL_FULL is not set CONFIG_PINCTRL_STM32=y +CONFIG_RAM=y +CONFIG_STM32_SDRAM=y # CONFIG_SPL_SERIAL_PRESENT is not set CONFIG_DM_SPI=y CONFIG_STM32_QSPI=y CONFIG_OF_LIBFDT_OVERLAY=y # CONFIG_EFI_LOADER is not set -CONFIG_CLK=y -CONFIG_PINCTRL=y -# CONFIG_PINCTRL_FULL is not set -CONFIG_PINCTRL_STM32=y -CONFIG_RAM=y -CONFIG_STM32_SDRAM=y -CONFIG_DM_GPIO=y -CONFIG_STM32F7_GPIO=y -CONFIG_SYS_MALLOC_F_LEN=0xC00
configs/tbs2910_defconfig +1 -1
@@ -2,10 +2,10 @@ CONFIG_ARM=y CONFIG_SYS_THUMB_BUILD=y CONFIG_ARCH_MX6=y CONFIG_TARGET_TBS2910=y -CONFIG_PRE_CONSOLE_BUFFER=y CONFIG_VIDEO=y CONFIG_FIT=y CONFIG_BOOTDELAY=3 +CONFIG_PRE_CONSOLE_BUFFER=y CONFIG_PRE_CON_BUF_ADDR=0x7c000000 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y
configs/xilinx_zynqmp_zc1751_xm015_dc1_defconfig +1 -1
@@ -3,8 +3,8 @@ CONFIG_SYS_CONFIG_NAME="xilinx_zynqmp_zc1751_xm015_dc1" CONFIG_ARCH_ZYNQMP=y CONFIG_SYS_TEXT_BASE=0x8000000 CONFIG_SYS_MALLOC_F_LEN=0x8000 -CONFIG_ZYNQMP_USB=y CONFIG_IDENT_STRING=" Xilinx ZynqMP ZC1751 xm015 dc1" +CONFIG_ZYNQMP_USB=y CONFIG_DEFAULT_DEVICE_TREE="zynqmp-zc1751-xm015-dc1" CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y
configs/xilinx_zynqmp_zc1751_xm016_dc2_defconfig +1 -1
@@ -4,9 +4,9 @@ CONFIG_ARCH_ZYNQMP=y CONFIG_SYS_TEXT_BASE=0x8000000 CONFIG_SYS_MALLOC_F_LEN=0x8000 # CONFIG_SPL_LIBDISK_SUPPORT is not set +CONFIG_IDENT_STRING=" Xilinx ZynqMP ZC1751 xm016 dc2" # CONFIG_SPL_FAT_SUPPORT is not set CONFIG_ZYNQMP_USB=y -CONFIG_IDENT_STRING=" Xilinx ZynqMP ZC1751 xm016 dc2" CONFIG_DEFAULT_DEVICE_TREE="zynqmp-zc1751-xm016-dc2" CONFIG_DISTRO_DEFAULTS=y CONFIG_FIT=y
configs/xilinx_zynqmp_zcu102_defconfig +1 -1
@@ -3,8 +3,8 @@ CONFIG_SYS_CONFIG_NAME="xilinx_zynqmp_zcu102" CONFIG_ARCH_ZYNQMP=y CONFIG_SYS_TEXT_BASE=0x8000000 CONFIG_SYS_MALLOC_F_LEN=0x8000 -CONFIG_ZYNQMP_USB=y CONFIG_IDENT_STRING=" Xilinx ZynqMP ZCU102" +CONFIG_ZYNQMP_USB=y CONFIG_DEFAULT_DEVICE_TREE="zynqmp-zcu102" CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y
configs/xilinx_zynqmp_zcu102_revB_defconfig +1 -1
@@ -3,8 +3,8 @@ CONFIG_SYS_CONFIG_NAME="xilinx_zynqmp_zcu102" CONFIG_ARCH_ZYNQMP=y CONFIG_SYS_TEXT_BASE=0x8000000 CONFIG_SYS_MALLOC_F_LEN=0x8000 -CONFIG_ZYNQMP_USB=y CONFIG_IDENT_STRING=" Xilinx ZynqMP ZCU102" +CONFIG_ZYNQMP_USB=y CONFIG_DEFAULT_DEVICE_TREE="zynqmp-zcu102-revB" CONFIG_AHCI=y CONFIG_DISTRO_DEFAULTS=y
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 2/47 Kconfig: Drop CONFIG_CMD_DS4510_INFO
In reply to Simon GlassThis option is only used in one driver and two boards. It does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by Simon Glass <[email protected]>
---
README | 1 - drivers/misc/ds4510.c | 8 -------- include/configs/xpedite517x.h | 1 - include/configs/xpedite537x.h | 1 - scripts/config_whitelist.txt | 1 - 5 files changed, 12 deletions(-)
README +0 -1
@@ -831,7 +831,6 @@ The following options need to be configured: CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics CONFIG_CMD_DS4510 * ds4510 I2C gpio commands - CONFIG_CMD_DS4510_INFO * ds4510 I2C info command CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd CONFIG_CMD_DS4510_RST * ds4510 I2C rst command CONFIG_CMD_DTT * Digital Therm and Thermostat
drivers/misc/ds4510.c +0 -8
@@ -186,7 +186,6 @@ int ds4510_gpio_read_val(uint8_t chip) }#ifdef CONFIG_CMD_DS4510 -#ifdef CONFIG_CMD_DS4510_INFO /* * Display DS4510 information */
@@ -240,7 +239,6 @@ static int ds4510_info(uint8_t chip)return 0 ; } -#endif /* CONFIG_CMD_DS4510_INFO */ cmd_tbl_t cmd_ds4510[] = {U_BOOT_CMD_MKENT (device,3 ,0 , (void *)DS4510_CMD_DEVICE ,"" ,"" ),
@@ -248,9 +246,7 @@ cmd_tbl_t cmd_ds4510[] = {U_BOOT_CMD_MKENT (output,4 ,0 , (void *)DS4510_CMD_OUTPUT ,"" ,"" ),U_BOOT_CMD_MKENT (input,3 ,0 , (void *)DS4510_CMD_INPUT ,"" ,"" ),U_BOOT_CMD_MKENT (pullup,4 ,0 , (void *)DS4510_CMD_PULLUP ,"" ,"" ), -#ifdef CONFIG_CMD_DS4510_INFOU_BOOT_CMD_MKENT (info,2 ,0 , (void *)DS4510_CMD_INFO ,"" ,"" ), -#endif #ifdef CONFIG_CMD_DS4510_RST U_BOOT_CMD_MKENT(rstdelay, 3, 0, (void *)DS4510_CMD_RSTDELAY, "", ""), #endif
@@ -324,10 +320,8 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])else tmp &= ~(1 << ul_arg2);return ds4510_pullup_write (chip, tmp); -#ifdef CONFIG_CMD_DS4510_INFO case DS4510_CMD_INFO :return ds4510_info (chip); -#endif #ifdef CONFIG_CMD_DS4510_RST case DS4510_CMD_RSTDELAY :return ds4510_rstdelay_write (chip, ul_arg2);
@@ -378,10 +372,8 @@ U_BOOT_CMD("ds4510 eeprom/seeprom/sram/gpio access" ,"device [dev]\n" " - show or set current device address\n" -#ifdef CONFIG_CMD_DS4510_INFO "ds4510 info\n" " - display ds4510 info\n" -#endif "ds4510 output pin 0|1\n" " - set pin low or high-Z\n" "ds4510 input pin\n"
include/configs/xpedite517x.h +0 -1
@@ -503,7 +503,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);* Command configuration. */ #define CONFIG_CMD_DS4510 -#define CONFIG_CMD_DS4510_INFO #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ
include/configs/xpedite537x.h +0 -1
@@ -355,7 +355,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);* Command configuration. */ #define CONFIG_CMD_DS4510 -#define CONFIG_CMD_DS4510_INFO #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2
scripts/config_whitelist.txt +0 -1
@@ -385,7 +385,6 @@ CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG CONFIG_CMD_DS4510 -CONFIG_CMD_DS4510_INFO CONFIG_CMD_DS4510_MEM CONFIG_CMD_DS4510_RST CONFIG_CMD_DTT
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 2/47 Kconfig: Drop CONFIG_CMD_DS4510_INFO
Quoted 6 lines · Simon Glass
This option is only used in one driver and two boards. It does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by Simon Glass <[email protected]>
Reviewed-by Tom Rini <[email protected]>
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/85b92a95/attachment.sig>
PATCH 2/47 Kconfig: Drop CONFIG_CMD_DS4510_INFO
In reply to Simon GlassHello Simon,
Am 15.05.2017 um 12:57 schrieb Simon Glass:
Quoted 6 lines
This option is only used in one driver and two boards. It does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by Simon Glass <[email protected]>
Quoted 8 lines
---
README | 1 - drivers/misc/ds4510.c | 8 -------- include/configs/xpedite517x.h | 1 - include/configs/xpedite537x.h | 1 - scripts/config_whitelist.txt | 1 - 5 files changed, 12 deletions(-)
Reviewed-by Heiko Schocher <[email protected]>
bye,
Heiko
Quoted 102 lines
README +0
-1@@ -831,7 +831,6 @@ The following options need to be configured: CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics CONFIG_CMD_DS4510 * ds4510 I2C gpio commands - CONFIG_CMD_DS4510_INFO * ds4510 I2C info command CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd CONFIG_CMD_DS4510_RST * ds4510 I2C rst command CONFIG_CMD_DTT * Digital Therm and Thermostatdrivers/misc/ds4510.c +0
-8@@ -186,7 +186,6 @@ int ds4510_gpio_read_val(uint8_t chip) }#ifdef CONFIG_CMD_DS4510 -#ifdef CONFIG_CMD_DS4510_INFO /* * Display DS4510 information */ @@ -240,7 +239,6 @@ static int ds4510_info(uint8_t chip)return 0 ; } -#endif /* CONFIG_CMD_DS4510_INFO */ cmd_tbl_t cmd_ds4510[] = {U_BOOT_CMD_MKENT (device,3 ,0 , (void *)DS4510_CMD_DEVICE ,"" ,"" ),@@ -248,9 +246,7 @@ cmd_tbl_t cmd_ds4510[] = {U_BOOT_CMD_MKENT (output,4 ,0 , (void *)DS4510_CMD_OUTPUT ,"" ,"" ),U_BOOT_CMD_MKENT (input,3 ,0 , (void *)DS4510_CMD_INPUT ,"" ,"" ),U_BOOT_CMD_MKENT (pullup,4 ,0 , (void *)DS4510_CMD_PULLUP ,"" ,"" ), -#ifdef CONFIG_CMD_DS4510_INFOU_BOOT_CMD_MKENT (info,2 ,0 , (void *)DS4510_CMD_INFO ,"" ,"" ), -#endif #ifdef CONFIG_CMD_DS4510_RST U_BOOT_CMD_MKENT(rstdelay, 3, 0, (void *)DS4510_CMD_RSTDELAY, "", ""), #endif@@ -324,10 +320,8 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])else tmp &= ~(1 << ul_arg2);return ds4510_pullup_write (chip, tmp); -#ifdef CONFIG_CMD_DS4510_INFO case DS4510_CMD_INFO :return ds4510_info (chip); -#endif #ifdef CONFIG_CMD_DS4510_RST case DS4510_CMD_RSTDELAY :return ds4510_rstdelay_write (chip, ul_arg2);@@ -378,10 +372,8 @@ U_BOOT_CMD("ds4510 eeprom/seeprom/sram/gpio access" ,"device [dev]\n" " - show or set current device address\n" -#ifdef CONFIG_CMD_DS4510_INFO "ds4510 info\n" " - display ds4510 info\n" -#endif "ds4510 output pin 0|1\n" " - set pin low or high-Z\n" "ds4510 input pin\n" include/configs/xpedite517x.h +0
-1@@ -503,7 +503,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);* Command configuration. */ #define CONFIG_CMD_DS4510 -#define CONFIG_CMD_DS4510_INFO #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ include/configs/xpedite537x.h +0
-1@@ -355,7 +355,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);* Command configuration. */ #define CONFIG_CMD_DS4510 -#define CONFIG_CMD_DS4510_INFO #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 scripts/config_whitelist.txt +0
-1@@ -385,7 +385,6 @@ CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG CONFIG_CMD_DS4510 -CONFIG_CMD_DS4510_INFO CONFIG_CMD_DS4510_MEM CONFIG_CMD_DS4510_RST CONFIG_CMD_DTT
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 3/47 Kconfig: Drop CONFIG_CMD_DS4510_MEM
In reply to Simon GlassThis option is only used in one driver and is not enabled by any board. It does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by Simon Glass <[email protected]>
---
README | 1 - drivers/misc/ds4510.c | 10 ---------- scripts/config_whitelist.txt | 1 - 3 files changed, 12 deletions(-)
README +0 -1
@@ -831,7 +831,6 @@ The following options need to be configured: CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics CONFIG_CMD_DS4510 * ds4510 I2C gpio commands - CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd CONFIG_CMD_DS4510_RST * ds4510 I2C rst command CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo arguments
drivers/misc/ds4510.c +0 -10
@@ -250,11 +250,9 @@ cmd_tbl_t cmd_ds4510[] = {#ifdef CONFIG_CMD_DS4510_RST U_BOOT_CMD_MKENT (rstdelay,3 ,0 , (void *)DS4510_CMD_RSTDELAY ,"" ,"" ), #endif -#ifdef CONFIG_CMD_DS4510_MEM U_BOOT_CMD_MKENT (eeprom,6 ,0 , (void *)DS4510_CMD_EEPROM ,"" ,"" ),U_BOOT_CMD_MKENT (seeprom,6 ,0 , (void *)DS4510_CMD_SEEPROM ,"" ,"" ), U_BOOT_CMD_MKENT(sram, 6, 0, (void *)DS4510_CMD_SRAM, "", ""), -#endif };int do_ds4510 (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[])
@@ -264,13 +262,11 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])ulong ul_arg2 =0 ;ulong ul_arg3 =0 ;int tmp; -#ifdef CONFIG_CMD_DS4510_MEM ulong addr;ulong off;ulong cnt;int end;int (*rw_func)(uint8_t ,int ,uint8_t *,int ); -#endif c =find_cmd_tbl (argv[1 ], cmd_ds4510,ARRAY_SIZE (cmd_ds4510));
@@ -326,7 +322,6 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])case DS4510_CMD_RSTDELAY :return ds4510_rstdelay_write (chip, ul_arg2);#endif -#ifdef CONFIG_CMD_DS4510_MEM case DS4510_CMD_EEPROM : end =DS4510_EEPROM +DS4510_EEPROM_SIZE ; off =DS4510_EEPROM ;
@@ -339,13 +334,11 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) end =DS4510_SRAM +DS4510_SRAM_SIZE ; off =DS4510_SRAM ;break ; -#endif default :/* We should never get here... */ return 1 ; } -#ifdef CONFIG_CMD_DS4510_MEM /* Only eeprom, seeprom, and sram commands should make it here */ if (strcmp (argv[2 ],"read" ) ==0 ) rw_func = ds4510_mem_read;
@@ -364,7 +357,6 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) }return rw_func (chip, off, (uint8_t *)addr, cnt); -#endif } U_BOOT_CMD(
@@ -387,7 +379,6 @@ U_BOOT_CMD("ds4510 rstdelay 0-3\n" " - set reset output delay"#endif -#ifdef CONFIG_CMD_DS4510_MEM "\n" "ds4510 eeprom read addr off cnt\n" "ds4510 eeprom write addr off cnt\n"
@@ -398,6 +389,5 @@ U_BOOT_CMD("ds4510 sram read addr off cnt\n" "ds4510 sram write addr off cnt\n" " - read/write 'cnt' bytes at SRAM offset 'off'" -#endif );#endif /* CONFIG_CMD_DS4510 */
scripts/config_whitelist.txt +0 -1
@@ -385,7 +385,6 @@ CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG CONFIG_CMD_DS4510 -CONFIG_CMD_DS4510_MEM CONFIG_CMD_DS4510_RST CONFIG_CMD_DTT CONFIG_CMD_ECCTEST
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 3/47 Kconfig: Drop CONFIG_CMD_DS4510_MEM
Quoted 6 lines · Simon Glass
This option is only used in one driver and is not enabled by any board. It does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by Simon Glass <[email protected]>
Reviewed-by Tom Rini <[email protected]>
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/55478d88/attachment.sig>
PATCH 3/47 Kconfig: Drop CONFIG_CMD_DS4510_MEM
In reply to Simon GlassHello Simon,
Am 15.05.2017 um 12:57 schrieb Simon Glass:
Quoted 5 lines
This option is only used in one driver and is not enabled by any board. It does not seem worth having the ability to remove this part of the support.
Drop the option.
Quoted 7 lines
Signed-off-by Simon Glass <[email protected]>---
README | 1 - drivers/misc/ds4510.c | 10 ---------- scripts/config_whitelist.txt | 1 - 3 files changed, 12 deletions(-)
Reviewed-by Heiko Schocher <[email protected]>
bye,
Heiko
Quoted 101 lines
README +0
-1@@ -831,7 +831,6 @@ The following options need to be configured: CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics CONFIG_CMD_DS4510 * ds4510 I2C gpio commands - CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd CONFIG_CMD_DS4510_RST * ds4510 I2C rst command CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo argumentsdrivers/misc/ds4510.c +0
-10@@ -250,11 +250,9 @@ cmd_tbl_t cmd_ds4510[] = {#ifdef CONFIG_CMD_DS4510_RST U_BOOT_CMD_MKENT (rstdelay,3 ,0 , (void *)DS4510_CMD_RSTDELAY ,"" ,"" ), #endif -#ifdef CONFIG_CMD_DS4510_MEM U_BOOT_CMD_MKENT (eeprom,6 ,0 , (void *)DS4510_CMD_EEPROM ,"" ,"" ),U_BOOT_CMD_MKENT (seeprom,6 ,0 , (void *)DS4510_CMD_SEEPROM ,"" ,"" ), U_BOOT_CMD_MKENT(sram, 6, 0, (void *)DS4510_CMD_SRAM, "", ""), -#endif };int do_ds4510 (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[])@@ -264,13 +262,11 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])ulong ul_arg2 =0 ;ulong ul_arg3 =0 ;int tmp; -#ifdef CONFIG_CMD_DS4510_MEM ulong addr;ulong off;ulong cnt;int end;int (*rw_func)(uint8_t ,int ,uint8_t *,int ); -#endif c =find_cmd_tbl (argv[1 ], cmd_ds4510,ARRAY_SIZE (cmd_ds4510));@@ -326,7 +322,6 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])case DS4510_CMD_RSTDELAY :return ds4510_rstdelay_write (chip, ul_arg2);#endif -#ifdef CONFIG_CMD_DS4510_MEM case DS4510_CMD_EEPROM : end =DS4510_EEPROM +DS4510_EEPROM_SIZE ; off =DS4510_EEPROM ;@@ -339,13 +334,11 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) end =DS4510_SRAM +DS4510_SRAM_SIZE ; off =DS4510_SRAM ;break ; -#endif default :/* We should never get here... */ return 1 ; } -#ifdef CONFIG_CMD_DS4510_MEM /* Only eeprom, seeprom, and sram commands should make it here */ if (strcmp (argv[2 ],"read" ) ==0 ) rw_func = ds4510_mem_read;@@ -364,7 +357,6 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) }return rw_func (chip, off, (uint8_t *)addr, cnt); -#endif } U_BOOT_CMD(@@ -387,7 +379,6 @@ U_BOOT_CMD("ds4510 rstdelay 0-3\n" " - set reset output delay"#endif -#ifdef CONFIG_CMD_DS4510_MEM "\n" "ds4510 eeprom read addr off cnt\n" "ds4510 eeprom write addr off cnt\n" @@ -398,6 +389,5 @@ U_BOOT_CMD("ds4510 sram read addr off cnt\n" "ds4510 sram write addr off cnt\n" " - read/write 'cnt' bytes at SRAM offset 'off'" -#endif );#endif /* CONFIG_CMD_DS4510 */ scripts/config_whitelist.txt +0
-1@@ -385,7 +385,6 @@ CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG CONFIG_CMD_DS4510 -CONFIG_CMD_DS4510_MEM CONFIG_CMD_DS4510_RST CONFIG_CMD_DTT CONFIG_CMD_ECCTEST
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 4/47 Kconfig: Drop CONFIG_CMD_DS4510_RST
In reply to Simon GlassThis option is only used in one driver and is not enabled by any board. It does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by Simon Glass <[email protected]>
---
README | 1 - drivers/misc/ds4510.c | 6 ------ scripts/config_whitelist.txt | 1 - 3 files changed, 8 deletions(-)
README +0 -1
@@ -831,7 +831,6 @@ The following options need to be configured: CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics CONFIG_CMD_DS4510 * ds4510 I2C gpio commands - CONFIG_CMD_DS4510_RST * ds4510 I2C rst command CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EDITENV edit env variable
drivers/misc/ds4510.c +0 -6
@@ -247,9 +247,7 @@ cmd_tbl_t cmd_ds4510[] = {U_BOOT_CMD_MKENT (input,3 ,0 , (void *)DS4510_CMD_INPUT ,"" ,"" ),U_BOOT_CMD_MKENT (pullup,4 ,0 , (void *)DS4510_CMD_PULLUP ,"" ,"" ),U_BOOT_CMD_MKENT (info,2 ,0 , (void *)DS4510_CMD_INFO ,"" ,"" ), -#ifdef CONFIG_CMD_DS4510_RSTU_BOOT_CMD_MKENT (rstdelay,3 ,0 , (void *)DS4510_CMD_RSTDELAY ,"" ,"" ), -#endifU_BOOT_CMD_MKENT (eeprom,6 ,0 , (void *)DS4510_CMD_EEPROM ,"" ,"" ),U_BOOT_CMD_MKENT (seeprom,6 ,0 , (void *)DS4510_CMD_SEEPROM ,"" ,"" ), U_BOOT_CMD_MKENT(sram, 6, 0, (void *)DS4510_CMD_SRAM, "", ""),
@@ -318,10 +316,8 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])return ds4510_pullup_write (chip, tmp);case DS4510_CMD_INFO :return ds4510_info (chip); -#ifdef CONFIG_CMD_DS4510_RST case DS4510_CMD_RSTDELAY :return ds4510_rstdelay_write (chip, ul_arg2); -#endif case DS4510_CMD_EEPROM : end =DS4510_EEPROM +DS4510_EEPROM_SIZE ; off =DS4510_EEPROM ;
@@ -374,11 +370,9 @@ U_BOOT_CMD(" - disable/enable pullup on specified pin\n" "ds4510 nv 0|1\n" " - make gpio and seeprom writes volatile/non-volatile" -#ifdef CONFIG_CMD_DS4510_RST"\n" "ds4510 rstdelay 0-3\n" " - set reset output delay" -#endif"\n" "ds4510 eeprom read addr off cnt\n" "ds4510 eeprom write addr off cnt\n"
scripts/config_whitelist.txt +0 -1
@@ -385,7 +385,6 @@ CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG CONFIG_CMD_DS4510 -CONFIG_CMD_DS4510_RST CONFIG_CMD_DTT CONFIG_CMD_ECCTEST CONFIG_CMD_EECONFIG
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 4/47 Kconfig: Drop CONFIG_CMD_DS4510_RST
Quoted 6 lines · Simon Glass
This option is only used in one driver and is not enabled by any board. It does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by Simon Glass <[email protected]>
Reviewed-by Tom Rini <[email protected]>
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/c5d43290/attachment.sig>
PATCH 4/47 Kconfig: Drop CONFIG_CMD_DS4510_RST
In reply to Simon GlassHello Simon,
Am 15.05.2017 um 12:57 schrieb Simon Glass:
Quoted 5 lines
This option is only used in one driver and is not enabled by any board. It does not seem worth having the ability to remove this part of the support.
Drop the option.
Quoted 7 lines
Signed-off-by Simon Glass <[email protected]>---
README | 1 - drivers/misc/ds4510.c | 6 ------ scripts/config_whitelist.txt | 1 - 3 files changed, 8 deletions(-)
Reviewed-by Heiko Schocher <[email protected]>
bye,
Heiko
Quoted 63 lines
README +0
-1@@ -831,7 +831,6 @@ The following options need to be configured: CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics CONFIG_CMD_DS4510 * ds4510 I2C gpio commands - CONFIG_CMD_DS4510_RST * ds4510 I2C rst command CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EDITENV edit env variabledrivers/misc/ds4510.c +0
-6@@ -247,9 +247,7 @@ cmd_tbl_t cmd_ds4510[] = {U_BOOT_CMD_MKENT (input,3 ,0 , (void *)DS4510_CMD_INPUT ,"" ,"" ),U_BOOT_CMD_MKENT (pullup,4 ,0 , (void *)DS4510_CMD_PULLUP ,"" ,"" ),U_BOOT_CMD_MKENT (info,2 ,0 , (void *)DS4510_CMD_INFO ,"" ,"" ), -#ifdef CONFIG_CMD_DS4510_RSTU_BOOT_CMD_MKENT (rstdelay,3 ,0 , (void *)DS4510_CMD_RSTDELAY ,"" ,"" ), -#endifU_BOOT_CMD_MKENT (eeprom,6 ,0 , (void *)DS4510_CMD_EEPROM ,"" ,"" ),U_BOOT_CMD_MKENT (seeprom,6 ,0 , (void *)DS4510_CMD_SEEPROM ,"" ,"" ), U_BOOT_CMD_MKENT(sram, 6, 0, (void *)DS4510_CMD_SRAM, "", ""),@@ -318,10 +316,8 @@ int do_ds4510(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])return ds4510_pullup_write (chip, tmp);case DS4510_CMD_INFO :return ds4510_info (chip); -#ifdef CONFIG_CMD_DS4510_RST case DS4510_CMD_RSTDELAY :return ds4510_rstdelay_write (chip, ul_arg2); -#endif case DS4510_CMD_EEPROM : end =DS4510_EEPROM +DS4510_EEPROM_SIZE ; off =DS4510_EEPROM ;@@ -374,11 +370,9 @@ U_BOOT_CMD(" - disable/enable pullup on specified pin\n" "ds4510 nv 0|1\n" " - make gpio and seeprom writes volatile/non-volatile" -#ifdef CONFIG_CMD_DS4510_RST"\n" "ds4510 rstdelay 0-3\n" " - set reset output delay" -#endif"\n" "ds4510 eeprom read addr off cnt\n" "ds4510 eeprom write addr off cnt\n" scripts/config_whitelist.txt +0
-1@@ -385,7 +385,6 @@ CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG CONFIG_CMD_DS4510 -CONFIG_CMD_DS4510_RST CONFIG_CMD_DTT CONFIG_CMD_ECCTEST CONFIG_CMD_EECONFIG
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 5/47 Kconfig: Drop CONFIG_CMD_DS4510
In reply to Simon GlassThis option enables a command in the driver. But the functions defined by the driver are not called anywhere else in U-Boot. So it does not seem useful to have this driver without its commands.
Drop this option, move the header file out of the common include/ directory and make all the function static.
Signed-off-by Simon Glass <[email protected]>
---
drivers/misc/ds4510.c | 22 ++++++++++------------
{include => drivers/misc}/ds4510.h | 10 ----------
include/configs/xpedite517x.h | 1 -
include/configs/xpedite537x.h | 1 -
scripts/config_whitelist.txt | 1 -
5 files changed, 10 insertions(+), 25 deletions(-)
rename {include => drivers/misc}/ds4510.h (75%)drivers/misc/ds4510.c +10 -12
@@ -12,7 +12,7 @@#include <common.h> #include <i2c.h> #include <command.h> -#include <ds4510.h> +#include "ds4510.h" /* Default to an address that hopefully won't corrupt other i2c devices */ #ifndef CONFIG_SYS_I2C_DS4510_ADDR
@@ -35,7 +35,7 @@ enum {/* * Write to DS4510, taking page boundaries into account */ -int ds4510_mem_write (uint8_t chip,int offset,uint8_t *buf,int count) +static int ds4510_mem_write (uint8_t chip,int offset,uint8_t *buf,int count) {int wrlen;int i =0 ;
@@ -64,7 +64,7 @@ int ds4510_mem_write(uint8_t chip, int offset, uint8_t *buf, int count)/* * General read from DS4510 */ -int ds4510_mem_read (uint8_t chip,int offset,uint8_t *buf,int count) +static int ds4510_mem_read (uint8_t chip,int offset,uint8_t *buf,int count) {return i2c_read (chip, offset,1 , buf, count); }
@@ -74,7 +74,7 @@ int ds4510_mem_read(uint8_t chip, int offset, uint8_t *buf, int count)* nv = 0 - Writes to SEEPROM registers behave like EEPROM * nv = 1 - Writes to SEEPROM registers behave like SRAM */ -int ds4510_see_write (uint8_t chip,uint8_t nv) +static int ds4510_see_write (uint8_t chip,uint8_t nv) {uint8_t data;
@@ -92,7 +92,7 @@ int ds4510_see_write(uint8_t chip, uint8_t nv)/* * Write de-assertion of reset signal delay */ -int ds4510_rstdelay_write (uint8_t chip,uint8_t delay) +static int ds4510_rstdelay_write (uint8_t chip,uint8_t delay) {uint8_t data;
@@ -108,7 +108,7 @@ int ds4510_rstdelay_write(uint8_t chip, uint8_t delay)/* * Write pullup characteristics of IO pins */ -int ds4510_pullup_write (uint8_t chip,uint8_t val) +static int ds4510_pullup_write (uint8_t chip,uint8_t val) { val &=DS4510_IO_MASK ;
@@ -118,7 +118,7 @@ int ds4510_pullup_write(uint8_t chip, uint8_t val)/* * Read pullup characteristics of IO pins */ -int ds4510_pullup_read (uint8_t chip) +static int ds4510_pullup_read (uint8_t chip) {uint8_t val;
@@ -131,7 +131,7 @@ int ds4510_pullup_read(uint8_t chip)/* * Write drive level of IO pins */ -int ds4510_gpio_write (uint8_t chip,uint8_t val) +static int ds4510_gpio_write (uint8_t chip,uint8_t val) {uint8_t data;int i;
@@ -155,7 +155,7 @@ int ds4510_gpio_write(uint8_t chip, uint8_t val)/* * Read drive level of IO pins */ -int ds4510_gpio_read (uint8_t chip) +static int ds4510_gpio_read (uint8_t chip) {uint8_t data;int val =0 ;
@@ -175,7 +175,7 @@ int ds4510_gpio_read(uint8_t chip)/* * Read physical level of IO pins */ -int ds4510_gpio_read_val (uint8_t chip) +static int ds4510_gpio_read_val (uint8_t chip) {uint8_t val;
@@ -185,7 +185,6 @@ int ds4510_gpio_read_val(uint8_t chip)return val &DS4510_IO_MASK ; } -#ifdef CONFIG_CMD_DS4510 /* * Display DS4510 information */
@@ -384,4 +383,3 @@ U_BOOT_CMD("ds4510 sram write addr off cnt\n" " - read/write 'cnt' bytes at SRAM offset 'off'" ); -#endif /* CONFIG_CMD_DS4510 */
drivers/misc/ds4510.h renamed from include/ds4510.h +0 -10
@@ -50,14 +50,4 @@#define DS4510_SRAM 0xfa#define DS4510_SRAM_SIZE 0x06 -int ds4510_mem_write (uint8_t chip,int offset,uint8_t *buf,int count); -int ds4510_mem_read (uint8_t chip,int offset,uint8_t *buf,int count); -int ds4510_see_write (uint8_t chip,uint8_t nv); -int ds4510_rstdelay_write (uint8_t chip,uint8_t delay); -int ds4510_pullup_write (uint8_t chip,uint8_t val); -int ds4510_pullup_read (uint8_t chip); -int ds4510_gpio_write (uint8_t chip,uint8_t val); -int ds4510_gpio_read (uint8_t chip); -int ds4510_gpio_read_val (uint8_t chip); -#endif /* __DS4510_H_ */
include/configs/xpedite517x.h +0 -1
@@ -502,7 +502,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_DS4510 #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ
include/configs/xpedite537x.h +0 -1
@@ -354,7 +354,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_DS4510 #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2
scripts/config_whitelist.txt +0 -1
@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_DS4510 CONFIG_CMD_DTT CONFIG_CMD_ECCTEST CONFIG_CMD_EECONFIG
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 5/47 Kconfig: Drop CONFIG_CMD_DS4510
Quoted 8 lines · Simon Glass
This option enables a command in the driver. But the functions defined by the driver are not called anywhere else in U-Boot. So it does not seem useful to have this driver without its commands.
Drop this option, move the header file out of the common
include/directory and make all the function static.Signed-off-by Simon Glass <[email protected]>
Reviewed-by Tom Rini <[email protected]>
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/53c3edd6/attachment.sig>
PATCH 5/47 Kconfig: Drop CONFIG_CMD_DS4510
In reply to Simon GlassHello Simon,
Am 15.05.2017 um 12:57 schrieb Simon Glass:
Quoted 10 lines
This option enables a command in the driver. But the functions defined by the driver are not called anywhere else in U-Boot. So it does not seem useful to have this driver without its commands.
Drop this option, move the header file out of the common
include/directory and make all the function static.Signed-off-by Simon Glass <[email protected]>---
Quoted 7 lines
drivers/misc/ds4510.c | 22 ++++++++++------------ {include => drivers/misc}/ds4510.h | 10 ---------- include/configs/xpedite517x.h | 1 - include/configs/xpedite537x.h | 1 - scripts/config_whitelist.txt | 1 - 5 files changed, 10 insertions(+), 25 deletions(-)rename {include =>
drivers/misc}/ds4510.h(75%)
Reviewed-by Heiko Schocher <[email protected]>
bye,
Heiko
Quoted 167 lines
drivers/misc/ds4510.c +10
-12@@ -12,7 +12,7 @@#include <common.h> #include <i2c.h> #include <command.h> -#include <ds4510.h> +#include "ds4510.h" /* Default to an address that hopefully won't corrupt other i2c devices */ #ifndef CONFIG_SYS_I2C_DS4510_ADDR @@ -35,7 +35,7 @@ enum {/* * Write to DS4510, taking page boundaries into account */ -int ds4510_mem_write (uint8_t chip,int offset,uint8_t *buf,int count) +static int ds4510_mem_write (uint8_t chip,int offset,uint8_t *buf,int count) {int wrlen;int i =0 ;@@ -64,7 +64,7 @@ int ds4510_mem_write(uint8_t chip, int offset, uint8_t *buf, int count)/* * General read from DS4510 */ -int ds4510_mem_read (uint8_t chip,int offset,uint8_t *buf,int count) +static int ds4510_mem_read (uint8_t chip,int offset,uint8_t *buf,int count) {return i2c_read (chip, offset,1 , buf, count); }@@ -74,7 +74,7 @@ int ds4510_mem_read(uint8_t chip, int offset, uint8_t *buf, int count)* nv = 0 - Writes to SEEPROM registers behave like EEPROM * nv = 1 - Writes to SEEPROM registers behave like SRAM */ -int ds4510_see_write (uint8_t chip,uint8_t nv) +static int ds4510_see_write (uint8_t chip,uint8_t nv) {uint8_t data;@@ -92,7 +92,7 @@ int ds4510_see_write(uint8_t chip, uint8_t nv)/* * Write de-assertion of reset signal delay */ -int ds4510_rstdelay_write (uint8_t chip,uint8_t delay) +static int ds4510_rstdelay_write (uint8_t chip,uint8_t delay) {uint8_t data;@@ -108,7 +108,7 @@ int ds4510_rstdelay_write(uint8_t chip, uint8_t delay)/* * Write pullup characteristics of IO pins */ -int ds4510_pullup_write (uint8_t chip,uint8_t val) +static int ds4510_pullup_write (uint8_t chip,uint8_t val) { val &=DS4510_IO_MASK ;@@ -118,7 +118,7 @@ int ds4510_pullup_write(uint8_t chip, uint8_t val)/* * Read pullup characteristics of IO pins */ -int ds4510_pullup_read (uint8_t chip) +static int ds4510_pullup_read (uint8_t chip) {uint8_t val;@@ -131,7 +131,7 @@ int ds4510_pullup_read(uint8_t chip)/* * Write drive level of IO pins */ -int ds4510_gpio_write (uint8_t chip,uint8_t val) +static int ds4510_gpio_write (uint8_t chip,uint8_t val) {uint8_t data;int i;@@ -155,7 +155,7 @@ int ds4510_gpio_write(uint8_t chip, uint8_t val)/* * Read drive level of IO pins */ -int ds4510_gpio_read (uint8_t chip) +static int ds4510_gpio_read (uint8_t chip) {uint8_t data;int val =0 ;@@ -175,7 +175,7 @@ int ds4510_gpio_read(uint8_t chip)/* * Read physical level of IO pins */ -int ds4510_gpio_read_val (uint8_t chip) +static int ds4510_gpio_read_val (uint8_t chip) {uint8_t val;@@ -185,7 +185,6 @@ int ds4510_gpio_read_val(uint8_t chip)return val &DS4510_IO_MASK ; } -#ifdef CONFIG_CMD_DS4510 /* * Display DS4510 information */ @@ -384,4 +383,3 @@ U_BOOT_CMD("ds4510 sram write addr off cnt\n" " - read/write 'cnt' bytes at SRAM offset 'off'" ); -#endif /* CONFIG_CMD_DS4510 */ drivers/misc/ds4510.h renamed from include/ds4510.h +0
-10@@ -50,14 +50,4 @@#define DS4510_SRAM 0xfa#define DS4510_SRAM_SIZE 0x06 -int ds4510_mem_write (uint8_t chip,int offset,uint8_t *buf,int count); -int ds4510_mem_read (uint8_t chip,int offset,uint8_t *buf,int count); -int ds4510_see_write (uint8_t chip,uint8_t nv); -int ds4510_rstdelay_write (uint8_t chip,uint8_t delay); -int ds4510_pullup_write (uint8_t chip,uint8_t val); -int ds4510_pullup_read (uint8_t chip); -int ds4510_gpio_write (uint8_t chip,uint8_t val); -int ds4510_gpio_read (uint8_t chip); -int ds4510_gpio_read_val (uint8_t chip); -#endif /* __DS4510_H_ */ include/configs/xpedite517x.h +0
-1@@ -502,7 +502,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_DS4510 #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ include/configs/xpedite537x.h +0
-1@@ -354,7 +354,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_DS4510 #define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 scripts/config_whitelist.txt +0
-1@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_DS4510 CONFIG_CMD_DTT CONFIG_CMD_ECCTEST CONFIG_CMD_EECONFIG
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 6/47 Convert CONFIG_DS4510 to Kconfig
In reply to Simon GlassThis converts the following to Kconfig:
CONFIG_DS4510
Signed-off-by Simon Glass <[email protected]>
---
README | 1 - configs/xpedite517x_defconfig | 1 + configs/xpedite537x_defconfig | 1 + drivers/misc/Kconfig | 8 ++++++++ include/configs/xpedite517x.h | 1 - include/configs/xpedite537x.h | 1 - scripts/config_whitelist.txt | 1 - 7 files changed, 10 insertions(+), 4 deletions(-)
README +0 -1
@@ -830,7 +830,6 @@ The following options need to be configured: CONFIG_CMD_CRC32 * crc32 CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics - CONFIG_CMD_DS4510 * ds4510 I2C gpio commands CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EDITENV edit env variable
configs/xpedite517x_defconfig +1 -0
@@ -15,6 +15,7 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_DATE=y +CONFIG_DS4510=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y
configs/xpedite537x_defconfig +1 -0
@@ -16,6 +16,7 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_DATE=y CONFIG_SYS_FSL_DDR2=y +CONFIG_DS4510=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=y
drivers/misc/Kconfig +8 -0
@@ -75,6 +75,14 @@ config CROS_EC_SPI provides a faster and more robust interface than I2C but the bugs are less interesting. +config DS4510 + bool "Enable support for DS4510 CPU supervisor" + help + Enable support for the Maxim DS4510 CPU supervisor. It has an + integrated 64-byte EEPROM, four programmable non-volatile I/O pins + and a configurable timer for the supervisor function. The device is + connected over I2C. + config FSL_SEC_MON bool "Enable FSL SEC_MON Driver" help
include/configs/xpedite517x.h +0 -1
@@ -249,7 +249,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_M41T11_BASE_YEAR 2000/* GPIO/EEPROM/SRAM */ -#define CONFIG_DS4510 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51/* GPIO */
include/configs/xpedite537x.h +0 -1
@@ -246,7 +246,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);#define CONFIG_SYS_M41T11_BASE_YEAR 2000/* GPIO/EEPROM/SRAM */ -#define CONFIG_DS4510 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51/* GPIO */
scripts/config_whitelist.txt +0 -1
@@ -683,7 +683,6 @@ CONFIG_DRIVE_MMC CONFIG_DRIVE_SATA CONFIG_DRIVE_TYPES CONFIG_DRIVE_USB -CONFIG_DS4510 CONFIG_DSP_CLUSTER_START CONFIG_DTT CONFIG_DTT_AD7414
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 6/47 Convert CONFIG_DS4510 to Kconfig
Quoted 4 lines · Simon Glass
This converts the following to
Kconfig:CONFIG_DS4510Signed-off-by Simon Glass <[email protected]>
Reviewed-by Tom Rini <[email protected]>
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/94ba9523/attachment.sig>
PATCH 6/47 Convert CONFIG_DS4510 to Kconfig
In reply to Simon GlassHello Simon,
Am 15.05.2017 um 12:57 schrieb Simon Glass:
Quoted 6 lines
This converts the following to
Kconfig:CONFIG_DS4510Signed-off-by Simon Glass <[email protected]>---
Quoted 8 lines
README | 1 - configs/xpedite517x_defconfig | 1 + configs/xpedite537x_defconfig | 1 + drivers/misc/Kconfig | 8 ++++++++ include/configs/xpedite517x.h | 1 - include/configs/xpedite537x.h | 1 - scripts/config_whitelist.txt | 1 - 7 files changed, 10 insertions(+), 4 deletions(-)
Reviewed-by Heiko Schocher <[email protected]>
bye,
Heiko
Quoted 93 lines
README +0
-1@@ -830,7 +830,6 @@ The following options need to be configured: CONFIG_CMD_CRC32 * crc32 CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics - CONFIG_CMD_DS4510 * ds4510 I2C gpio commands CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EDITENV edit env variableconfigs/xpedite517x_defconfig +1
-0@@ -15,6 +15,7 @@ CONFIG_CMD_MII=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_DATE=y +CONFIG_DS4510=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=yconfigs/xpedite537x_defconfig +1
-0@@ -16,6 +16,7 @@ CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y CONFIG_CMD_DATE=y CONFIG_SYS_FSL_DDR2=y +CONFIG_DS4510=y # CONFIG_MMC is not set CONFIG_MTD_NOR_FLASH=y CONFIG_SYS_NS16550=ydrivers/misc/Kconfig +8
-0@@ -75,6 +75,14 @@ config CROS_EC_SPI provides a faster and more robust interface than I2C but the bugs are less interesting. +config DS4510 + bool "Enable support for DS4510 CPU supervisor" + help + Enable support for the Maxim DS4510 CPU supervisor. It has an + integrated 64-byte EEPROM, four programmable non-volatile I/O pins + and a configurable timer for the supervisor function. The device is + connected over I2C. + config FSL_SEC_MON bool "Enable FSL SEC_MON Driver" helpinclude/configs/xpedite517x.h +0
-1@@ -249,7 +249,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_M41T11_BASE_YEAR 2000/* GPIO/EEPROM/SRAM */ -#define CONFIG_DS4510 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51/* GPIO */ include/configs/xpedite537x.h +0
-1@@ -246,7 +246,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);#define CONFIG_SYS_M41T11_BASE_YEAR 2000/* GPIO/EEPROM/SRAM */ -#define CONFIG_DS4510 #define CONFIG_SYS_I2C_DS4510_ADDR 0x51/* GPIO */ scripts/config_whitelist.txt +0
-1@@ -683,7 +683,6 @@ CONFIG_DRIVE_MMC CONFIG_DRIVE_SATA CONFIG_DRIVE_TYPES CONFIG_DRIVE_USB -CONFIG_DS4510 CONFIG_DSP_CLUSTER_START CONFIG_DTT CONFIG_DTT_AD7414
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 7/47 Kconfig: Drop CONFIG_SYS_I2C_DTT_ADDR
In reply to Simon GlassThis option is only defined to a non-default value by canyonlands, which needs conversion to driver model (where the I2C address would be defined by the device tree).
Drop this option.
Signed-off-by Simon Glass <[email protected]>
---
README | 6 ------ drivers/hwmon/ds1775.c | 2 +- drivers/hwmon/lm75.c | 4 ---- include/configs/canyonlands.h | 4 ---- include/configs/kilauea.h | 1 - include/configs/makalu.h | 1 - scripts/config_whitelist.txt | 1 - 7 files changed, 1 insertion(+), 18 deletions(-)
README +0 -6
@@ -2391,12 +2391,6 @@ The following options need to be configured: If defined, then this indicates the I2C bus number for the DTT. If not defined, then U-Boot assumes that DTT is on I2C bus 0. - CONFIG_SYS_I2C_DTT_ADDR: - - If defined, specifies the I2C address of the DTT device. - If not defined, then U-Boot uses predefined value for - specified DTT device. - CONFIG_SOFT_I2C_READ_REPEATED_START defining this will force the i2c_read() function in
drivers/hwmon/ds1775.c +1 -1
@@ -11,7 +11,7 @@#include <i2c.h> #include <dtt.h> -#define DTT_I2C_DEV_CODE CONFIG_SYS_I2C_DTT_ADDR/* Dallas Semi's DS1775 device code */ +#define DTT_I2C_DEV_CODE 0x48/* Dallas Semi's DS1775 device code */ #define DTT_READ_TEMP 0x0#define DTT_CONFIG 0x1#define DTT_TEMP_HYST 0x2
drivers/hwmon/lm75.c +0 -4
@@ -16,11 +16,7 @@/* * Device code */ -#if defined(CONFIG_SYS_I2C_DTT_ADDR ) -#define DTT_I2C_DEV_CODE CONFIG_SYS_I2C_DTT_ADDR -#else #define DTT_I2C_DEV_CODE 0x48/* ON Semi's LM75 device */ -#endif #define DTT_READ_TEMP 0x0#define DTT_CONFIG 0x1#define DTT_TEMP_HYST 0x2
include/configs/canyonlands.h +0 -4
@@ -269,10 +269,6 @@#define CONFIG_SYS_DTT_LOW_TEMP -30#define CONFIG_SYS_DTT_HYSTERESIS 3 -#if defined(CONFIG_ARCHES ) -#define CONFIG_SYS_I2C_DTT_ADDR 0x4a/* AD7414 I2C address */ -#endif -#if !defined(CONFIG_ARCHES )/* RTC configuration */ #define CONFIG_RTC_M41T62
include/configs/kilauea.h +0 -1
@@ -320,7 +320,6 @@/* Standard DTT sensor configuration */ #define CONFIG_DTT_DS1775 1#define CONFIG_DTT_SENSORS { 0 } -#define CONFIG_SYS_I2C_DTT_ADDR 0x48/* RTC configuration */ #define CONFIG_RTC_DS1338 1
include/configs/makalu.h +0 -1
@@ -192,7 +192,6 @@/* Standard DTT sensor configuration */ #define CONFIG_DTT_DS1775 1#define CONFIG_DTT_SENSORS { 0 } -#define CONFIG_SYS_I2C_DTT_ADDR 0x48/* RTC configuration */ #define CONFIG_RTC_X1205 1
scripts/config_whitelist.txt +0 -1
@@ -4232,7 +4232,6 @@ CONFIG_SYS_I2C_DSPIC_2_ADDR CONFIG_SYS_I2C_DSPIC_ADDR CONFIG_SYS_I2C_DSPIC_IO_ADDR CONFIG_SYS_I2C_DSPIC_KEYB_ADDR -CONFIG_SYS_I2C_DTT_ADDR CONFIG_SYS_I2C_DVI_ADDR CONFIG_SYS_I2C_DVI_BUS_NUM CONFIG_SYS_I2C_EARLY_INIT
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 7/47 Kconfig: Drop CONFIG_SYS_I2C_DTT_ADDR
Quoted 7 lines · Simon Glass
This option is only defined to a non-default value by canyonlands, which needs conversion to driver model (where the I2C address would be defined by the device tree).
Drop this option.
Signed-off-by Simon Glass <[email protected]>
Reviewed-by Tom Rini <[email protected]>
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/e1a212fd/attachment.sig>
PATCH 7/47 Kconfig: Drop CONFIG_SYS_I2C_DTT_ADDR
In reply to Simon GlassHello Simon,
Am 15.05.2017 um 12:57 schrieb Simon Glass:
Quoted 9 lines
This option is only defined to a non-default value by canyonlands, which needs conversion to driver model (where the I2C address would be defined by the device tree).
Drop this option.
Signed-off-by Simon Glass <[email protected]>---
Quoted 8 lines
README | 6 ------ drivers/hwmon/ds1775.c | 2 +- drivers/hwmon/lm75.c | 4 ---- include/configs/canyonlands.h | 4 ---- include/configs/kilauea.h | 1 - include/configs/makalu.h | 1 - scripts/config_whitelist.txt | 1 - 7 files changed, 1 insertion(+), 18 deletions(-)
Reviewed-by Heiko Schocher <[email protected]>
bye,
Heiko
Quoted 99 lines
README +0
-6@@ -2391,12 +2391,6 @@ The following options need to be configured: If defined, then this indicates the I2C bus number for the DTT. If not defined, then U-Boot assumes that DTT is on I2C bus 0. - CONFIG_SYS_I2C_DTT_ADDR: - - If defined, specifies the I2C address of the DTT device. - If not defined, then U-Boot uses predefined value for - specified DTT device. - CONFIG_SOFT_I2C_READ_REPEATED_START defining this will force the i2c_read() function indrivers/hwmon/ds1775.c +1
-1@@ -11,7 +11,7 @@#include <i2c.h> #include <dtt.h> -#define DTT_I2C_DEV_CODE CONFIG_SYS_I2C_DTT_ADDR/* Dallas Semi's DS1775 device code */ +#define DTT_I2C_DEV_CODE 0x48/* Dallas Semi's DS1775 device code */ #define DTT_READ_TEMP 0x0#define DTT_CONFIG 0x1#define DTT_TEMP_HYST 0x2drivers/hwmon/lm75.c +0
-4@@ -16,11 +16,7 @@/* * Device code */ -#if defined(CONFIG_SYS_I2C_DTT_ADDR ) -#define DTT_I2C_DEV_CODE CONFIG_SYS_I2C_DTT_ADDR -#else #define DTT_I2C_DEV_CODE 0x48/* ON Semi's LM75 device */ -#endif #define DTT_READ_TEMP 0x0#define DTT_CONFIG 0x1#define DTT_TEMP_HYST 0x2include/configs/canyonlands.h +0
-4@@ -269,10 +269,6 @@#define CONFIG_SYS_DTT_LOW_TEMP -30#define CONFIG_SYS_DTT_HYSTERESIS 3 -#if defined(CONFIG_ARCHES ) -#define CONFIG_SYS_I2C_DTT_ADDR 0x4a/* AD7414 I2C address */ -#endif -#if !defined(CONFIG_ARCHES )/* RTC configuration */ #define CONFIG_RTC_M41T62 include/configs/kilauea.h +0
-1@@ -320,7 +320,6 @@/* Standard DTT sensor configuration */ #define CONFIG_DTT_DS1775 1#define CONFIG_DTT_SENSORS { 0 } -#define CONFIG_SYS_I2C_DTT_ADDR 0x48/* RTC configuration */ #define CONFIG_RTC_DS1338 1include/configs/makalu.h +0
-1@@ -192,7 +192,6 @@/* Standard DTT sensor configuration */ #define CONFIG_DTT_DS1775 1#define CONFIG_DTT_SENSORS { 0 } -#define CONFIG_SYS_I2C_DTT_ADDR 0x48/* RTC configuration */ #define CONFIG_RTC_X1205 1scripts/config_whitelist.txt +0
-1@@ -4232,7 +4232,6 @@ CONFIG_SYS_I2C_DSPIC_2_ADDR CONFIG_SYS_I2C_DSPIC_ADDR CONFIG_SYS_I2C_DSPIC_IO_ADDR CONFIG_SYS_I2C_DSPIC_KEYB_ADDR -CONFIG_SYS_I2C_DTT_ADDR CONFIG_SYS_I2C_DVI_ADDR CONFIG_SYS_I2C_DVI_BUS_NUM CONFIG_SYS_I2C_EARLY_INIT
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 8/47 Drop three-wire serial (TWS) support
In reply to Simon GlassThis subsystem has not been converted to driver model, there is only one driver and only one board that uses it. Drop it and its CONFIG option.
Also drop the rtc4543 RTC driver since it uses TWS.
Signed-off-by Simon Glass <[email protected]>
---
configs/inka4x0_defconfig | 1 - drivers/Makefile | 1 - drivers/rtc/Makefile | 1 - drivers/rtc/rtc4543.c | 101 ------------------------------------------- drivers/twserial/Makefile | 8 ---- drivers/twserial/soft_tws.c | 94 ---------------------------------------- include/configs/inka4x0.h | 80 ---------------------------------- include/tws.h | 21 --------- scripts/config_whitelist.txt | 2 - 9 files changed, 309 deletions(-) delete mode 100644 drivers/rtc/rtc4543.c delete mode 100644 drivers/twserial/Makefile delete mode 100644 drivers/twserial/soft_tws.c delete mode 100644 include/tws.h
configs/inka4x0_defconfig +0 -1
@@ -8,7 +8,6 @@ CONFIG_CMD_USB=y CONFIG_CMD_DHCP=y CONFIG_CMD_PING=y CONFIG_CMD_SNTP=y -CONFIG_CMD_DATE=y CONFIG_CMD_EXT2=y CONFIG_CMD_FAT=y CONFIG_MAC_PARTITION=y
drivers/Makefile +0 -1
@@ -86,7 +86,6 @@ obj-y += spmi/ obj-y += sysreset/ obj-y += timer/ obj-y += tpm/ -obj-y += twserial/ obj-y += video/ obj-y += watchdog/ obj-$(CONFIG_QE) += qe/
drivers/rtc/Makefile +0 -1
@@ -48,7 +48,6 @@ obj-$(CONFIG_RTC_PCF2127) += pcf2127.o obj-$(CONFIG_RTC_PL031) += pl031.o obj-$(CONFIG_RTC_PT7C4338) += pt7c4338.o obj-$(CONFIG_RTC_RS5C372A) += rs5c372.o -obj-$(CONFIG_RTC_RTC4543) += rtc4543.o obj-$(CONFIG_RTC_RV3029) += rv3029.o obj-$(CONFIG_RTC_RX8025) += rx8025.o obj-$(CONFIG_RTC_S3C24X0) += s3c24x0_rtc.o
drivers/rtc/rtc4543.c deleted +0 -101
101 lines not on this page · raw message
drivers/twserial/Makefile deleted +0 -8
@@ -1,8 +0,0 @@ -# -# (C) Copyright 2009 -# Detlev Zundel, DENX Software Engineering, dzu at denx.de. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-$(CONFIG_SOFT_TWS) += soft_tws.o
drivers/twserial/soft_tws.c deleted +0 -94
94 lines not on this page · raw message
include/configs/inka4x0.h +0 -80
86 lines not on this page · raw message
include/tws.h deleted +0 -21
@@ -1,21 +0,0 @@ -/* -* (C) Copyright 2009 -* Detlev Zundel, DENX Software Engineering, dzu at denx.de. -* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -#ifndef _TWS_H_ -#define _TWS_H_ - -/* -* Read/Write interface: -* buffer: Where to read/write the data -* len: How many bits to read/write -* -* Returns: 0 on success, not 0 on failure -*/ -int tws_read (uchar *buffer,int len); -int tws_write (uchar *buffer,int len); - -#endif /* _TWS_H_ */
scripts/config_whitelist.txt +0 -2
@@ -2372,7 +2372,6 @@ CONFIG_RTC_MV CONFIG_RTC_MXS CONFIG_RTC_PCF8563 CONFIG_RTC_PT7C4338 -CONFIG_RTC_RTC4543 CONFIG_RTC_RV3029 CONFIG_RTC_RX8025 CONFIG_RTC_X1205
@@ -2605,7 +2604,6 @@ CONFIG_SOFT_I2C_GPIO_SCL CONFIG_SOFT_I2C_GPIO_SDA CONFIG_SOFT_I2C_READ_REPEATED_START CONFIG_SOFT_SPI -CONFIG_SOFT_TWS CONFIG_SOURCE CONFIG_SPARSE_RCU_POINTER CONFIG_SPDDRAM_SILENT
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 8/47 Drop three-wire serial (TWS) support
Quoted 8 lines · Simon Glass
This subsystem has not been converted to driver model, there is only one driver and only one board that uses it. Drop it and its CONFIG option.
Also drop the rtc4543 RTC driver since it uses TWS.
Signed-off-by Simon Glass <[email protected]>---
Quoted 14 lines
configs/inka4x0_defconfig | 1 - drivers/Makefile | 1 - drivers/rtc/Makefile | 1 - drivers/rtc/rtc4543.c | 101 ------------------------------------------- drivers/twserial/Makefile | 8 ---- drivers/twserial/soft_tws.c | 94 ---------------------------------------- include/configs/inka4x0.h | 80 ---------------------------------- include/tws.h | 21 --------- scripts/config_whitelist.txt | 2 - 9 files changed, 309 deletions(-) delete mode 100644 drivers/rtc/rtc4543.c delete mode 100644 drivers/twserial/Makefile delete mode 100644 drivers/twserial/soft_tws.c delete mode 100644 include/tws.h
Anatolij, this is used only by a board you maintain, do you want to update the framework here or should we drop the board in question as well? Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/1bfe745f/attachment.sig>
PATCH 8/47 Drop three-wire serial (TWS) support
On Mon, 15 May 2017 12:32:49 -0400
Tom Rini trini at konsulko.com wrote:
...
Quoted 3 lines
Anatolij, this is used only by a board you maintain, do you want to update the framework here or should we drop the board in question as well? Thanks!
We should drop this board, together with other mpc5xxx boards and mpc5xxx arch support, I think.
--
Anatolij
PATCH 9/47 Drop digital thermometer and thermostat (DTT) drivers
In reply to Simon GlassThis subsystem is quite old. It has been replaced with a driver-model version (UCLASS_THERMAL). Boards are free to convert to that if required, but here is a removal patch that could be applied in the meantime.
Signed-off-by Simon Glass <[email protected]>
---
README | 6 -- board/gdsys/405ep/dlvision-10g.c | 10 ++- board/gdsys/405ep/io.c | 10 ++- board/gdsys/405ep/neo.c | 10 ++- board/gdsys/405ex/io64.c | 10 ++- cmd/Makefile | 1 - cmd/dtt.c | 120 --------------------------- drivers/Kconfig | 2 - drivers/Makefile | 1 - drivers/hwmon/Kconfig | 0 drivers/hwmon/Makefile | 22 ----- drivers/hwmon/adm1021.c | 164 ------------------------------------- drivers/hwmon/adt7460.c | 73 ----------------- drivers/hwmon/ds1621.c | 155 ----------------------------------- drivers/hwmon/ds1722.c | 137 ------------------------------- drivers/hwmon/ds1775.c | 126 ---------------------------- drivers/hwmon/ds620.c | 65 --------------- drivers/hwmon/lm63.c | 160 ------------------------------------ drivers/hwmon/lm73.c | 146 --------------------------------- drivers/hwmon/lm75.c | 139 ------------------------------- drivers/hwmon/lm81.c | 111 ------------------------- include/config_cmd_all.h | 1 - include/configs/PMC440.h | 21 ----- include/configs/TQM834x.h | 8 -- include/configs/UCP1020.h | 21 ----- include/configs/acadia.h | 9 -- include/configs/canyonlands.h | 11 --- include/configs/dlvision-10g.h | 8 -- include/configs/dlvision.h | 1 - include/configs/exynos5-common.h | 2 - include/configs/intip.h | 8 -- include/configs/io.h | 6 -- include/configs/io64.h | 9 -- include/configs/katmai.h | 25 ------ include/configs/kilauea.h | 4 - include/configs/km/km-powerpc.h | 1 - include/configs/km/km83xx-common.h | 7 -- include/configs/km82xx.h | 7 -- include/configs/makalu.h | 5 -- include/configs/motionpro.h | 3 - include/configs/neo.h | 8 -- include/configs/odroid_xu3.h | 1 - include/configs/sequoia.h | 9 -- include/configs/socrates.h | 8 -- include/configs/tqma6.h | 10 --- include/configs/tqma6_mba6.h | 2 - include/configs/tqma6_wru4.h | 4 - include/configs/work_92105.h | 8 -- include/configs/xilinx-ppc.h | 1 - include/configs/xpedite517x.h | 3 - include/configs/xpedite537x.h | 3 - include/configs/xpedite550x.h | 3 - include/configs/yosemite.h | 9 -- include/dtt.h | 47 ----------- include/i2c.h | 3 - scripts/config_whitelist.txt | 22 ----- 56 files changed, 28 insertions(+), 1738 deletions(-) delete mode 100644 cmd/dtt.c delete mode 100644 drivers/hwmon/Kconfig delete mode 100644 drivers/hwmon/Makefile delete mode 100644 drivers/hwmon/adm1021.c delete mode 100644 drivers/hwmon/adt7460.c delete mode 100644 drivers/hwmon/ds1621.c delete mode 100644 drivers/hwmon/ds1722.c delete mode 100644 drivers/hwmon/ds1775.c delete mode 100644 drivers/hwmon/ds620.c delete mode 100644 drivers/hwmon/lm63.c delete mode 100644 drivers/hwmon/lm73.c delete mode 100644 drivers/hwmon/lm75.c delete mode 100644 drivers/hwmon/lm81.c delete mode 100644 include/dtt.h
README +0 -6
@@ -830,7 +830,6 @@ The following options need to be configured: CONFIG_CMD_CRC32 * crc32 CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics - CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EDITENV edit env variable CONFIG_CMD_EEPROM * EEPROM read/write support
@@ -2386,11 +2385,6 @@ The following options need to be configured: If defined, then this indicates the I2C bus number for the RTC. If not defined, then U-Boot assumes that RTC is on I2C bus 0. - CONFIG_SYS_DTT_BUS_NUM - - If defined, then this indicates the I2C bus number for the DTT. - If not defined, then U-Boot assumes that DTT is on I2C bus 0. - CONFIG_SOFT_I2C_READ_REPEATED_START defining this will force the i2c_read() function in
board/gdsys/405ep/dlvision-10g.c +7 -3
@@ -10,7 +10,6 @@#include <asm/processor.h> #include <asm/io.h> #include <asm/ppc4xx-gpio.h> -#include <dtt.h> #include "405ep.h" #include <gdsys_fpga.h>
@@ -61,8 +60,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;int misc_init_r (void ) { -/* startup fans */ -dtt_init (); +/* +* Note: DTT has been removed. Please use UCLASS_THERMAL. +* +* startup fans +* +* dtt_init(); +*/ return 0 ; }
board/gdsys/405ep/io.c +7 -3
@@ -11,7 +11,6 @@#include <asm/io.h> #include <asm/ppc4xx-gpio.h> -#include <dtt.h> #include <miiphy.h> #include "405ep.h"
@@ -41,8 +40,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;int misc_init_r (void ) { -/* startup fans */ -dtt_init (); +/* +* Note: DTT has been removed. Please use UCLASS_THERMAL. +* +* startup fans +* +* dtt_init(); +*/ return 0 ; }
board/gdsys/405ep/neo.c +7 -3
@@ -10,7 +10,6 @@#include <asm/processor.h> #include <asm/io.h> #include <asm/ppc4xx-gpio.h> -#include <dtt.h> #include "405ep.h" #include <gdsys_fpga.h>
@@ -32,8 +31,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;int misc_init_r (void ) { -/* startup fans */ -dtt_init (); +/* +* Note: DTT has been removed. Please use UCLASS_THERMAL. +* +* startup fans +* +* dtt_init(); +*/ return 0 ; }
board/gdsys/405ex/io64.c +7 -3
@@ -26,7 +26,6 @@#include <miiphy.h> #include <i2c.h> -#include <dtt.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -70,8 +69,13 @@ static inline void blank_string(int size)*/ int misc_init_r (void ) { -/* startup fans */ -dtt_init (); +/* +* Note: DTT has been removed. Please use UCLASS_THERMAL. +* +* startup fans +* +* dtt_init(); +*/ #ifdef CONFIG_ENV_IS_IN_FLASH /* Monitor protection ON by default */
cmd/Makefile +0 -1
@@ -43,7 +43,6 @@ ifdef CONFIG_POST obj-$(CONFIG_CMD_DIAG) += diag.o endif obj-$(CONFIG_CMD_DISPLAY) += display.o -obj-$(CONFIG_CMD_DTT) += dtt.o obj-$(CONFIG_CMD_ECHO) += echo.o obj-$(CONFIG_ENV_IS_IN_EEPROM) += eeprom.o obj-$(CONFIG_CMD_EEPROM) += eeprom.o
cmd/dtt.c deleted +0 -120
120 lines not on this page · raw message
drivers/Kconfig +0 -2
@@ -30,8 +30,6 @@ source "drivers/fpga/Kconfig" source "drivers/gpio/Kconfig" -source "drivers/hwmon/Kconfig" - source "drivers/i2c/Kconfig" source "drivers/input/Kconfig"
drivers/Makefile +0 -1
@@ -74,7 +74,6 @@ obj-$(CONFIG_CPU) += cpu/ obj-y += crypto/ obj-y += firmware/ obj-$(CONFIG_FPGA) += fpga/ -obj-y += hwmon/ obj-y += misc/ obj-y += pcmcia/ obj-y += dfu/
drivers/hwmon/Kconfig deleted +0 -0
drivers/hwmon/Makefile deleted +0 -22
@@ -1,22 +0,0 @@ -# -# (C) Copyright 2006 -# Wolfgang Denk, DENX Software Engineering, wd at denx.de. -# -# (C) Copyright 2001 -# Erik Theisen, Wave 7 Optics, etheisen at mindspring.com. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -#ccflags-y += -DDEBUG - -obj-$(CONFIG_DTT_ADM1021) += adm1021.o -obj-$(CONFIG_DTT_ADT7460) += adt7460.o -obj-$(CONFIG_DTT_DS1621) += ds1621.o -obj-$(CONFIG_DTT_DS1722) += ds1722.o -obj-$(CONFIG_DTT_DS1775) += ds1775.o -obj-$(CONFIG_DTT_DS620) += ds620.o -obj-$(CONFIG_DTT_LM63) += lm63.o -obj-$(CONFIG_DTT_LM73) += lm73.o -obj-$(CONFIG_DTT_LM75) += lm75.o -obj-$(CONFIG_DTT_LM81) += lm81.o
drivers/hwmon/adm1021.c deleted +0 -164
164 lines not on this page · raw message
drivers/hwmon/adt7460.c deleted +0 -73
73 lines not on this page · raw message
drivers/hwmon/ds1621.c deleted +0 -155
155 lines not on this page · raw message
drivers/hwmon/ds1722.c deleted +0 -137
137 lines not on this page · raw message
drivers/hwmon/ds1775.c deleted +0 -126
126 lines not on this page · raw message
drivers/hwmon/ds620.c deleted +0 -65
65 lines not on this page · raw message
drivers/hwmon/lm63.c deleted +0 -160
160 lines not on this page · raw message
drivers/hwmon/lm73.c deleted +0 -146
146 lines not on this page · raw message
drivers/hwmon/lm75.c deleted +0 -139
139 lines not on this page · raw message
drivers/hwmon/lm81.c deleted +0 -111
111 lines not on this page · raw message
include/config_cmd_all.h +0 -1
@@ -13,7 +13,6 @@* Alphabetical list of all possible commands. */ -#define CONFIG_CMD_DTT /* Digital Therm and Thermostat */ #define CONFIG_CMD_EEPROM /* EEPROM read/write support */ #define CONFIG_CMD_FDC /* Floppy Disk Support */ #define CONFIG_CMD_FUSE /* Device fuse support */
include/configs/PMC440.h +0 -21
@@ -163,26 +163,6 @@#define CONFIG_SYS_EEPROM_WREN 1#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52 -/* -* standard dtt sensor configuration - bottom bit will determine local or -* remote sensor of the TMP401 -*/ -#define CONFIG_DTT_SENSORS { 0, 1 } - -/* -* The PMC440 uses a TI TMP401 temperature sensor. This part -* is basically compatible to the ADM1021 that is supported -* by U-Boot. -* -* - i2c addr 0x4c -* - conversion rate 0x02 = 0.25 conversions/second -* - ALERT ouput disabled -* - local temp sensor enabled, min set to 0 deg, max set to 70 deg -* - remote temp sensor enabled, min set to 0 deg, max set to 70 deg -*/ -#define CONFIG_DTT_ADM1021 -#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} } -#define CONFIG_PREBOOT "echo Add \\\"run fpga\\\" and " \ "\\\"painit\\\" to preboot command"
@@ -258,7 +238,6 @@/* Partitions */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI
include/configs/TQM834x.h +0 -8
@@ -184,13 +184,6 @@#define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */ #define CONFIG_SYS_I2C_RTC_ADDR 0x68/* at address 0x68 */ -/* I2C SYSMON (LM75) */ -#define CONFIG_DTT_LM75 1/* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -/* * TSEC */
@@ -280,7 +273,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO
include/configs/UCP1020.h +0 -21
@@ -129,27 +129,6 @@#define CONFIG_HWCONFIG -#define CONFIG_DTT_ADM1021 1/* ADM1021 temp sensor support */ -#define CONFIG_SYS_DTT_BUS_NUM 1/* The I2C bus for DTT */ -#define CONFIG_DTT_SENSORS { 0, 1 }/* Sensor index */ -/* -* ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details). -* there will be one entry in this array for each two (dummy) sensors in -* CONFIG_DTT_SENSORS. -* -* For uCP1020 module: -* - only one ADM1021/NCT72 -* - i2c addr 0x41 -* - conversion rate 0x02 = 0.25 conversions/second -* - ALERT output disabled -* - local temp sensor enabled, min set to 0 deg, max set to 85 deg -* - remote temp sensor enabled, min set to 0 deg, max set to 85 deg -*/ -#define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \ - 0x02, 0, 1, 0, 85, 1, 0, 85} } - -#define CONFIG_CMD_DTT -/* * These can be toggled for performance analysis, otherwise use default. */
include/configs/acadia.h +0 -9
@@ -124,14 +124,6 @@#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1/* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 1/* use AD7414 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -/*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/
@@ -160,7 +152,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND /*-----------------------------------------------------------------------
include/configs/canyonlands.h +0 -11
@@ -261,14 +261,6 @@#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 /* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 /* use AD7414 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -#if !defined(CONFIG_ARCHES )/* RTC configuration */ #define CONFIG_RTC_M41T62
@@ -369,17 +361,14 @@* Commands additional to the ones defined in amcc-common.h */ #if defined(CONFIG_ARCHES ) -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM #elif defined(CONFIG_CANYONLANDS ) -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SATA #define CONFIG_CMD_SDRAM #elif defined(CONFIG_GLACIER ) -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM
include/configs/dlvision-10g.h +0 -8
@@ -57,7 +57,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ
@@ -111,13 +110,6 @@#define CONFIG_SYS_SPD_BUS_NUM 4/* Temp sensor/hwmon/dtt */ -#define CONFIG_SYS_DTT_BUS_NUM 4 -#define CONFIG_DTT_LM63 1/* National LM63 */ -#define CONFIG_DTT_SENSORS { 0x4c, 0x4e, 0x18 }/* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 46, 10 }, { 48, 14 }, { 50, 19 }, { 52, 23 },\ - { 54, 27 }, { 56, 31 }, { 58, 36 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10#define CONFIG_SYS_ICS8N3QV01_I2C {1, 3}#define CONFIG_SYS_SIL1178_I2C {0, 2}
include/configs/dlvision.h +0 -1
@@ -55,7 +55,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ
include/configs/exynos5-common.h +0 -2
@@ -46,8 +46,6 @@/* Thermal Management Unit */ #define CONFIG_EXYNOS_TMU -#define CONFIG_CMD_DTT -#define CONFIG_TMU_CMD_DTT /* MMC SPL */ #define COPY_BL2_FNPTR_ADDR 0x02020030
include/configs/intip.h +0 -8
@@ -218,13 +218,6 @@#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* I2C SYSMON */ -#define CONFIG_DTT_LM63 1/* National LM63 */ -#define CONFIG_DTT_SENSORS { 0 }/* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 50, 20 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 -/* RTC configuration */ #define CONFIG_RTC_DS1337 1#define CONFIG_SYS_I2C_RTC_ADDR 0x68
@@ -272,7 +265,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM
include/configs/io.h +0 -6
@@ -57,7 +57,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ
@@ -93,11 +92,6 @@#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000/* Temp sensor/hwmon/dtt */ -#define CONFIG_DTT_LM63 1/* National LM63 */ -#define CONFIG_DTT_SENSORS { 0 }/* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 50, 20 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10/* * FLASH organization
include/configs/io64.h +0 -9
@@ -327,14 +327,6 @@#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* Temp sensor/hwmon/dtt */ -#define CONFIG_DTT_LM63 1/* National LM63 */ -#define CONFIG_DTT_SENSORS { 0x18, 0x4c, 0x4e }/* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 43, 13 }, { 46, 16 }, \ - { 50, 20 }, { 53, 27 }, { 56, 34 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 -/*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/
@@ -373,7 +365,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORY
include/configs/katmai.h +0 -25
@@ -123,31 +123,6 @@#define CONFIG_SYS_I2C_RTC_ADDR 0x68#define CONFIG_SYS_M41T11_BASE_YEAR 1900/* play along with linux */ -/* I2C DTT */ -#define CONFIG_DTT_ADM1021 1/* ADM1021 temp sensor support */ -#define CONFIG_SYS_DTT_BUS_NUM 1/* The I2C bus for DTT */ -/* -* standard dtt sensor configuration - bottom bit will determine local or -* remote sensor of the ADM1021, the rest determines index into -* CONFIG_SYS_DTT_ADM1021 array below. -*/ -#define CONFIG_DTT_SENSORS { 0, 1 } - -/* -* ADM1021 temp sensor configuration (see dtt/adm1021.c for details). -* there will be one entry in this array for each two (dummy) sensors in -* CONFIG_DTT_SENSORS. -* -* For Katmai board: -* - only one ADM1021 -* - i2c addr 0x18 -* - conversion rate 0x02 = 0.25 conversions/second -* - ALERT ouput disabled -* - local temp sensor enabled, min set to 0 deg, max set to 85 deg -* - remote temp sensor enabled, min set to 0 deg, max set to 85 deg -*/ -#define CONFIG_SYS_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} } -/*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/
include/configs/kilauea.h +0 -4
@@ -317,10 +317,6 @@#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* Standard DTT sensor configuration */ -#define CONFIG_DTT_DS1775 1 -#define CONFIG_DTT_SENSORS { 0 } -/* RTC configuration */ #define CONFIG_RTC_DS1338 1#define CONFIG_SYS_I2C_RTC_ADDR 0x68
include/configs/km/km-powerpc.h +0 -1
@@ -14,7 +14,6 @@#define CONFIG_BOOTCOUNT_LIMIT -#define CONFIG_CMD_DTT #define CONFIG_JFFS2_CMDLINE /* standard km ethernet_present for piggy */
include/configs/km/km83xx-common.h +0 -7
@@ -215,13 +215,6 @@#define CONFIG_KM_IVM_BUS 2/* I2C2 (Mux-Port 1)*/ -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0, 1, 2, 3}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM 1 -#if defined(CONFIG_CMD_NAND )#define CONFIG_NAND_KMETER1 #define CONFIG_SYS_MAX_NAND_DEVICE 1
include/configs/km82xx.h +0 -7
@@ -268,13 +268,6 @@ int get_sda(void);int get_scl (void );#endif -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM 2 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_IMMR 0xF0000000
include/configs/makalu.h +0 -5
@@ -189,10 +189,6 @@#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52/* I2C boot EEPROM (24C02BN) */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1/* Bytes of address */ -/* Standard DTT sensor configuration */ -#define CONFIG_DTT_DS1775 1 -#define CONFIG_DTT_SENSORS { 0 } -/* RTC configuration */ #define CONFIG_RTC_X1205 1#define CONFIG_SYS_I2C_RTC_ADDR 0x6f
@@ -231,7 +227,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI /* POST support */
include/configs/motionpro.h +0 -3
@@ -33,7 +33,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IMMAP
@@ -286,8 +285,6 @@/* * Temperature sensor */ -#define CONFIG_DTT_LM75 1 -#define CONFIG_DTT_SENSORS { 0x49 }/* * Environment settings
include/configs/neo.h +0 -8
@@ -57,7 +57,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ
@@ -100,13 +99,6 @@#define CONFIG_RTC_DS1337 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 -/* Temp sensor/hwmon/dtt */ -#define CONFIG_DTT_LM63 1/* National LM63 */ -#define CONFIG_DTT_SENSORS { 0 }/* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 50, 20 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 -/* * FLASH organization */
include/configs/odroid_xu3.h +0 -1
@@ -62,7 +62,6 @@/* FIXME: MUST BE REMOVED AFTER TMU IS TURNED ON */ #undef CONFIG_EXYNOS_TMU -#undef CONFIG_TMU_CMD_DTT#define CONFIG_DFU_ALT_SYSTEM \ "uImage fat 0 1;" \
include/configs/sequoia.h +0 -9
@@ -159,14 +159,6 @@#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1/* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 1/* use AD7414 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -/* * Default environment variables */
@@ -222,7 +214,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM
include/configs/socrates.h +0 -8
@@ -210,13 +210,6 @@/* I2C W83782G HW-Monitoring IC */ #define CONFIG_SYS_I2C_W83782G_ADDR 0x28/* W83782G address */ -/* I2C temp sensor */ -/* Socrates uses Maxim's DS75, which is compatible with LM75 */ -#define CONFIG_DTT_LM75 1 -#define CONFIG_DTT_SENSORS {4}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 125 -#define CONFIG_SYS_DTT_LOW_TEMP -55 -#define CONFIG_SYS_DTT_HYSTERESIS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4/*
@@ -286,7 +279,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM#define CONFIG_CMD_SDRAM #define CONFIG_CMD_REGINFO
include/configs/tqma6.h +0 -10
@@ -57,13 +57,6 @@#define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_I2C_SPEED 100000 -/* I2C SYSMON (LM75) */ -#define CONFIG_DTT_LM75 -#define CONFIG_DTT_MAX_TEMP 70 -#define CONFIG_DTT_MIN_TEMP -30 -#define CONFIG_DTT_HYSTERESIS 3 -#define CONFIG_CMD_DTT -/* I2C EEPROM (M24C64) */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
@@ -373,8 +366,5 @@#endif /* Support at least the sensor on TQMa6 SOM */ -#if !defined(CONFIG_DTT_SENSORS ) -#define CONFIG_DTT_SENSORS { 0 } -#endif #endif /* __CONFIG_H */
include/configs/tqma6_mba6.h +0 -2
@@ -10,8 +10,6 @@#ifndef __CONFIG_TQMA6_MBA6_H#define __CONFIG_TQMA6_MBA6_H -#define CONFIG_DTT_SENSORS { 0, 1 } -#define CONFIG_FEC_XCV_TYPE RGMII#define CONFIG_ETHPRIME "FEC"
include/configs/tqma6_wru4.h +0 -4
@@ -7,10 +7,6 @@#ifndef __CONFIG_TQMA6_WRU4_H#define __CONFIG_TQMA6_WRU4_H -/* DTT sensors */ -#define CONFIG_DTT_SENSORS { 0, 1 } -#define CONFIG_SYS_DTT_BUS_NUM 2 -/* Ethernet */ #define CONFIG_FEC_XCV_TYPE RMII#define CONFIG_ETHPRIME "FEC"
include/configs/work_92105.h +0 -8
@@ -84,14 +84,6 @@#define CONFIG_RTC_DS1374 -/* -* I2C Temperature Sensor (DTT) -*/ - -#define CONFIG_CMD_DTT -#define CONFIG_DTT_SENSORS { 0, 1 } -#define CONFIG_DTT_DS620 -/* * U-Boot General Configurations */
include/configs/xilinx-ppc.h +0 -1
@@ -28,7 +28,6 @@#define CONFIG_CMD_REGINFO #undef CONFIG_CMD_JFFS2#undef CONFIG_CMD_MTDPARTS -#undef CONFIG_CMD_DTT#undef CONFIG_CMD_EEPROM/*Misc*/
include/configs/xpedite517x.h +0 -3
@@ -233,8 +233,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);/* I2C DS1631 temperature sensor */ #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 -#define CONFIG_DTT_DS1621 -#define CONFIG_DTT_SENSORS { 0 }#define CONFIG_SYS_I2C_LM90_ADDR 0x4c/* I2C EEPROM - AT24C128B */
@@ -501,7 +499,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ #define CONFIG_CMD_JFFS2
include/configs/xpedite537x.h +0 -3
@@ -230,8 +230,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);/* I2C DS1631 temperature sensor */ #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 -#define CONFIG_DTT_DS1621 -#define CONFIG_DTT_SENSORS { 0 }#define CONFIG_SYS_I2C_LM90_ADDR 0x4c/* I2C EEPROM - AT24C128B */
@@ -353,7 +351,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NAND
include/configs/xpedite550x.h +0 -3
@@ -219,8 +219,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100/* I2C DS7505 temperature sensor */ -#define CONFIG_DTT_LM75 -#define CONFIG_DTT_SENSORS { 0 }#define CONFIG_SYS_I2C_LM75_ADDR 0x48/* I2C ADT7461 temperature sensor */
@@ -339,7 +337,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NAND
include/configs/yosemite.h +0 -9
@@ -131,14 +131,6 @@#define CONFIG_ENV_OFFSET 0x0#endif /* CONFIG_ENV_IS_IN_EEPROM */ -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1/* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 1/* use AD7414 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -/* * Default environment variables */
@@ -184,7 +176,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI #ifdef CONFIG_440EP
include/dtt.h deleted +0 -47
47 lines not on this page · raw message
include/i2c.h +0 -3
@@ -571,9 +571,6 @@ void i2c_dump_msgs(struct i2c_msg *msg, int nmsgs);#if !defined(CONFIG_SYS_RTC_BUS_NUM )#define CONFIG_SYS_RTC_BUS_NUM 0#endif -#if !defined(CONFIG_SYS_DTT_BUS_NUM ) -#define CONFIG_SYS_DTT_BUS_NUM 0 -#endif #if !defined(CONFIG_SYS_SPD_BUS_NUM )#define CONFIG_SYS_SPD_BUS_NUM 0#endif
scripts/config_whitelist.txt +0 -22
@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_DTT CONFIG_CMD_ECCTEST CONFIG_CMD_EECONFIG CONFIG_CMD_EEPROM
@@ -684,20 +683,6 @@ CONFIG_DRIVE_SATA CONFIG_DRIVE_TYPES CONFIG_DRIVE_USB CONFIG_DSP_CLUSTER_START -CONFIG_DTT -CONFIG_DTT_AD7414 -CONFIG_DTT_ADM1021 -CONFIG_DTT_DS1621 -CONFIG_DTT_DS1775 -CONFIG_DTT_DS620 -CONFIG_DTT_HYSTERESIS -CONFIG_DTT_LM63 -CONFIG_DTT_LM75 -CONFIG_DTT_MAX_TEMP -CONFIG_DTT_MIN_TEMP -CONFIG_DTT_PWM_LOOKUPTABLE -CONFIG_DTT_SENSORS -CONFIG_DTT_TACH_LIMIT CONFIG_DUOVERO CONFIG_DV_USBPHY_CTL CONFIG_DWC2_DFLT_SPEED_FULL
@@ -3476,12 +3461,6 @@ CONFIG_SYS_DSPI_CTAR4 CONFIG_SYS_DSPI_CTAR5 CONFIG_SYS_DSPI_CTAR6 CONFIG_SYS_DSPI_CTAR7 -CONFIG_SYS_DTT_ADM1021 -CONFIG_SYS_DTT_BUS_NUM -CONFIG_SYS_DTT_HYSTERESIS -CONFIG_SYS_DTT_LOW_TEMP -CONFIG_SYS_DTT_MAX_TEMP -CONFIG_SYS_DTT_MIN_TEMP CONFIG_SYS_DUART_RST CONFIG_SYS_DV_CLKMODE CONFIG_SYS_DV_NOR_BOOT_CFG
@@ -6142,7 +6121,6 @@ CONFIG_TIZEN CONFIG_TI_KEYSTONE_SERDES CONFIG_TI_KSNAV CONFIG_TI_SPI_MMAP -CONFIG_TMU_CMD_DTT CONFIG_TMU_TIMER CONFIG_TOTAL5200 CONFIG_TPL_DRIVERS_MISC_SUPPORT
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 9/47 Drop digital thermometer and thermostat (DTT) drivers
Quoted 70 lines · Simon Glass
This subsystem is quite old. It has been replaced with a driver-model version (
UCLASS_THERMAL). Boards are free to convert to that if required, but here is a removal patch that could be applied in the meantime.Signed-off-by Simon Glass <[email protected]>---
README | 6 -- board/gdsys/405ep/dlvision-10g.c | 10 ++- board/gdsys/405ep/io.c | 10 ++- board/gdsys/405ep/neo.c | 10 ++- board/gdsys/405ex/io64.c | 10 ++- cmd/Makefile | 1 - cmd/dtt.c | 120 --------------------------- drivers/Kconfig | 2 - drivers/Makefile | 1 - drivers/hwmon/Kconfig | 0 drivers/hwmon/Makefile | 22 ----- drivers/hwmon/adm1021.c | 164 ------------------------------------- drivers/hwmon/adt7460.c | 73 ----------------- drivers/hwmon/ds1621.c | 155 ----------------------------------- drivers/hwmon/ds1722.c | 137 ------------------------------- drivers/hwmon/ds1775.c | 126 ---------------------------- drivers/hwmon/ds620.c | 65 --------------- drivers/hwmon/lm63.c | 160 ------------------------------------ drivers/hwmon/lm73.c | 146 --------------------------------- drivers/hwmon/lm75.c | 139 ------------------------------- drivers/hwmon/lm81.c | 111 ------------------------- include/config_cmd_all.h | 1 - include/configs/PMC440.h | 21 ----- include/configs/TQM834x.h | 8 -- include/configs/UCP1020.h | 21 ----- include/configs/acadia.h | 9 -- include/configs/canyonlands.h | 11 --- include/configs/dlvision-10g.h | 8 -- include/configs/dlvision.h | 1 - include/configs/exynos5-common.h | 2 - include/configs/intip.h | 8 -- include/configs/io.h | 6 -- include/configs/io64.h | 9 -- include/configs/katmai.h | 25 ------ include/configs/kilauea.h | 4 - include/configs/km/km-powerpc.h | 1 - include/configs/km/km83xx-common.h | 7 -- include/configs/km82xx.h | 7 -- include/configs/makalu.h | 5 -- include/configs/motionpro.h | 3 - include/configs/neo.h | 8 -- include/configs/odroid_xu3.h | 1 - include/configs/sequoia.h | 9 -- include/configs/socrates.h | 8 -- include/configs/tqma6.h | 10 --- include/configs/tqma6_mba6.h | 2 - include/configs/tqma6_wru4.h | 4 - include/configs/work_92105.h | 8 -- include/configs/xilinx-ppc.h | 1 - include/configs/xpedite517x.h | 3 - include/configs/xpedite537x.h | 3 - include/configs/xpedite550x.h | 3 - include/configs/yosemite.h | 9 -- include/dtt.h | 47 ----------- include/i2c.h | 3 - scripts/config_whitelist.txt | 22 ----- 56 files changed, 28 insertions(+), 1738 deletions(-) delete mode 100644 cmd/dtt.c delete mode 100644 drivers/hwmon/Kconfig delete mode 100644 drivers/hwmon/Makefile delete mode 100644 drivers/hwmon/adm1021.c delete mode 100644 drivers/hwmon/adt7460.c delete mode 100644 drivers/hwmon/ds1621.c
Quoted 8 lines
delete mode 100644 drivers/hwmon/ds1722.c delete mode 100644 drivers/hwmon/ds1775.c delete mode 100644 drivers/hwmon/ds620.c delete mode 100644 drivers/hwmon/lm63.c delete mode 100644 drivers/hwmon/lm73.c delete mode 100644 drivers/hwmon/lm75.c delete mode 100644 drivers/hwmon/lm81.c delete mode 100644 include/dtt.h
So, this touches a lot of boards that have active maintainer, lets ping them now and see if anyone wants to step up and start converting some of these drivers over. I'm not nak'ing this patch but raising awareness that some stuff people depend on needs to be updated.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/7a41ebfd/attachment.sig>
PATCH 9/47 Drop digital thermometer and thermostat (DTT) drivers
Hi Tom,
Quoted 81 lines · Tom Rini
Quoted 70 lines · Simon Glass
This subsystem is quite old. It has been replaced with a driver-model version (
UCLASS_THERMAL). Boards are free to convert to that if required, but here is a removal patch that could be applied in the meantime.Signed-off-by Simon Glass <[email protected]>---
README | 6 -- board/gdsys/405ep/dlvision-10g.c | 10 ++- board/gdsys/405ep/io.c | 10 ++- board/gdsys/405ep/neo.c | 10 ++- board/gdsys/405ex/io64.c | 10 ++- cmd/Makefile | 1 - cmd/dtt.c | 120 --------------------------- drivers/Kconfig | 2 - drivers/Makefile | 1 - drivers/hwmon/Kconfig | 0 drivers/hwmon/Makefile | 22 ----- drivers/hwmon/adm1021.c | 164 ------------------------------------- drivers/hwmon/adt7460.c | 73 ----------------- drivers/hwmon/ds1621.c | 155 ----------------------------------- drivers/hwmon/ds1722.c | 137 ------------------------------- drivers/hwmon/ds1775.c | 126 ---------------------------- drivers/hwmon/ds620.c | 65 --------------- drivers/hwmon/lm63.c | 160 ------------------------------------ drivers/hwmon/lm73.c | 146 --------------------------------- drivers/hwmon/lm75.c | 139 ------------------------------- drivers/hwmon/lm81.c | 111 ------------------------- include/config_cmd_all.h | 1 - include/configs/PMC440.h | 21 ----- include/configs/TQM834x.h | 8 -- include/configs/UCP1020.h | 21 ----- include/configs/acadia.h | 9 -- include/configs/canyonlands.h | 11 --- include/configs/dlvision-10g.h | 8 -- include/configs/dlvision.h | 1 - include/configs/exynos5-common.h | 2 - include/configs/intip.h | 8 -- include/configs/io.h | 6 -- include/configs/io64.h | 9 -- include/configs/katmai.h | 25 ------ include/configs/kilauea.h | 4 - include/configs/km/km-powerpc.h | 1 - include/configs/km/km83xx-common.h | 7 -- include/configs/km82xx.h | 7 -- include/configs/makalu.h | 5 -- include/configs/motionpro.h | 3 - include/configs/neo.h | 8 -- include/configs/odroid_xu3.h | 1 - include/configs/sequoia.h | 9 -- include/configs/socrates.h | 8 -- include/configs/tqma6.h | 10 --- include/configs/tqma6_mba6.h | 2 - include/configs/tqma6_wru4.h | 4 - include/configs/work_92105.h | 8 -- include/configs/xilinx-ppc.h | 1 - include/configs/xpedite517x.h | 3 - include/configs/xpedite537x.h | 3 - include/configs/xpedite550x.h | 3 - include/configs/yosemite.h | 9 -- include/dtt.h | 47 ----------- include/i2c.h | 3 - scripts/config_whitelist.txt | 22 ----- 56 files changed, 28 insertions(+), 1738 deletions(-) delete mode 100644 cmd/dtt.c delete mode 100644 drivers/hwmon/Kconfig delete mode 100644 drivers/hwmon/Makefile delete mode 100644 drivers/hwmon/adm1021.c delete mode 100644 drivers/hwmon/adt7460.c delete mode 100644 drivers/hwmon/ds1621.cQuoted 8 lines
delete mode 100644 drivers/hwmon/ds1722.c delete mode 100644 drivers/hwmon/ds1775.c delete mode 100644 drivers/hwmon/ds620.c delete mode 100644 drivers/hwmon/lm63.c delete mode 100644 drivers/hwmon/lm73.c delete mode 100644 drivers/hwmon/lm75.c delete mode 100644 drivers/hwmon/lm81.c delete mode 100644 include/dtt.h
Quoted 4 lines
So, this touches a lot of boards that have active maintainer, lets ping them now and see if anyone wants to step up and start converting some of these drivers over. I'm not nak'ing this patch but raising awareness that some stuff people depend on needs to be updated.
Sounds good. Sorry for skipping the cc - I really need to make time to fix up patman unicode soon.
Regards,
Simon
PATCH 9/47 Drop digital thermometer and thermostat (DTT) drivers
In reply to Simon GlassHello Simon,
Am 15.05.2017 um 12:57 schrieb Simon Glass:
Quoted 64 lines
This subsystem is quite old. It has been replaced with a driver-model version (
UCLASS_THERMAL). Boards are free to convert to that if required, but here is a removal patch that could be applied in the meantime.Signed-off-by Simon Glass <[email protected]>---
README | 6 -- board/gdsys/405ep/dlvision-10g.c | 10 ++- board/gdsys/405ep/io.c | 10 ++- board/gdsys/405ep/neo.c | 10 ++- board/gdsys/405ex/io64.c | 10 ++- cmd/Makefile | 1 - cmd/dtt.c | 120 --------------------------- drivers/Kconfig | 2 - drivers/Makefile | 1 - drivers/hwmon/Kconfig | 0 drivers/hwmon/Makefile | 22 ----- drivers/hwmon/adm1021.c | 164 ------------------------------------- drivers/hwmon/adt7460.c | 73 ----------------- drivers/hwmon/ds1621.c | 155 ----------------------------------- drivers/hwmon/ds1722.c | 137 ------------------------------- drivers/hwmon/ds1775.c | 126 ---------------------------- drivers/hwmon/ds620.c | 65 --------------- drivers/hwmon/lm63.c | 160 ------------------------------------ drivers/hwmon/lm73.c | 146 --------------------------------- drivers/hwmon/lm75.c | 139 ------------------------------- drivers/hwmon/lm81.c | 111 ------------------------- include/config_cmd_all.h | 1 - include/configs/PMC440.h | 21 ----- include/configs/TQM834x.h | 8 -- include/configs/UCP1020.h | 21 ----- include/configs/acadia.h | 9 -- include/configs/canyonlands.h | 11 --- include/configs/dlvision-10g.h | 8 -- include/configs/dlvision.h | 1 - include/configs/exynos5-common.h | 2 - include/configs/intip.h | 8 -- include/configs/io.h | 6 -- include/configs/io64.h | 9 -- include/configs/katmai.h | 25 ------ include/configs/kilauea.h | 4 - include/configs/km/km-powerpc.h | 1 - include/configs/km/km83xx-common.h | 7 -- include/configs/km82xx.h | 7 -- include/configs/makalu.h | 5 -- include/configs/motionpro.h | 3 - include/configs/neo.h | 8 -- include/configs/odroid_xu3.h | 1 - include/configs/sequoia.h | 9 -- include/configs/socrates.h | 8 -- include/configs/tqma6.h | 10 --- include/configs/tqma6_mba6.h | 2 - include/configs/tqma6_wru4.h | 4 - include/configs/work_92105.h | 8 -- include/configs/xilinx-ppc.h | 1 - include/configs/xpedite517x.h | 3 - include/configs/xpedite537x.h | 3 - include/configs/xpedite550x.h | 3 - include/configs/yosemite.h | 9 -- include/dtt.h | 47 ----------- include/i2c.h | 3 - scripts/config_whitelist.txt | 22 ----- 56 files changed, 28 insertions(+), 1738 deletions(-)
Quoted 14 lines
delete mode 100644
cmd/dtt.c
delete mode 100644drivers/hwmon/Kconfig
delete mode 100644drivers/hwmon/Makefile
delete mode 100644drivers/hwmon/adm1021.c
delete mode 100644drivers/hwmon/adt7460.c
delete mode 100644drivers/hwmon/ds1621.c
delete mode 100644drivers/hwmon/ds1722.c
delete mode 100644drivers/hwmon/ds1775.c
delete mode 100644drivers/hwmon/ds620.c
delete mode 100644drivers/hwmon/lm63.c
delete mode 100644drivers/hwmon/lm73.c
delete mode 100644drivers/hwmon/lm75.c
delete mode 100644drivers/hwmon/lm81.c
delete mode 100644include/dtt.h
Reviewed-by Heiko Schocher <[email protected]>
bye,
Heiko
Quoted 2,500 lines
README +0
-6@@ -830,7 +830,6 @@ The following options need to be configured: CONFIG_CMD_CRC32 * crc32 CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics - CONFIG_CMD_DTT * Digital Therm and Thermostat CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EDITENV edit env variable CONFIG_CMD_EEPROM * EEPROM read/write support@@ -2386,11 +2385,6 @@ The following options need to be configured: If defined, then this indicates the I2C bus number for the RTC. If not defined, then U-Boot assumes that RTC is on I2C bus 0. - CONFIG_SYS_DTT_BUS_NUM - - If defined, then this indicates the I2C bus number for the DTT. - If not defined, then U-Boot assumes that DTT is on I2C bus 0. - CONFIG_SOFT_I2C_READ_REPEATED_START defining this will force the i2c_read() function inboard/gdsys/405ep/dlvision-10g.c +7
-3@@ -10,7 +10,6 @@#include <asm/processor.h> #include <asm/io.h> #include <asm/ppc4xx-gpio.h> -#include <dtt.h> #include "405ep.h" #include <gdsys_fpga.h> @@ -61,8 +60,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;int misc_init_r (void ) { -/* startup fans */ -dtt_init (); +/* +* Note: DTT has been removed. Please use UCLASS_THERMAL. +* +* startup fans +* +* dtt_init(); +*/ return 0 ; }board/gdsys/405ep/io.c +7
-3@@ -11,7 +11,6 @@#include <asm/io.h> #include <asm/ppc4xx-gpio.h> -#include <dtt.h> #include <miiphy.h> #include "405ep.h" @@ -41,8 +40,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;int misc_init_r (void ) { -/* startup fans */ -dtt_init (); +/* +* Note: DTT has been removed. Please use UCLASS_THERMAL. +* +* startup fans +* +* dtt_init(); +*/ return 0 ; }board/gdsys/405ep/neo.c +7
-3@@ -10,7 +10,6 @@#include <asm/processor.h> #include <asm/io.h> #include <asm/ppc4xx-gpio.h> -#include <dtt.h> #include "405ep.h" #include <gdsys_fpga.h> @@ -32,8 +31,13 @@ struct ihs_fpga *fpga_ptr[] = CONFIG_SYS_FPGA_PTR;int misc_init_r (void ) { -/* startup fans */ -dtt_init (); +/* +* Note: DTT has been removed. Please use UCLASS_THERMAL. +* +* startup fans +* +* dtt_init(); +*/ return 0 ; }board/gdsys/405ex/io64.c +7
-3@@ -26,7 +26,6 @@#include <miiphy.h> #include <i2c.h> -#include <dtt.h> DECLARE_GLOBAL_DATA_PTR ;@@ -70,8 +69,13 @@ static inline void blank_string(int size)*/ int misc_init_r (void ) { -/* startup fans */ -dtt_init (); +/* +* Note: DTT has been removed. Please use UCLASS_THERMAL. +* +* startup fans +* +* dtt_init(); +*/ #ifdef CONFIG_ENV_IS_IN_FLASH /* Monitor protection ON by default */ cmd/Makefile +0
-1@@ -43,7 +43,6 @@ ifdef CONFIG_POST obj-$(CONFIG_CMD_DIAG) += diag.o endif obj-$(CONFIG_CMD_DISPLAY) += display.o -obj-$(CONFIG_CMD_DTT) += dtt.o obj-$(CONFIG_CMD_ECHO) += echo.o obj-$(CONFIG_ENV_IS_IN_EEPROM) += eeprom.o obj-$(CONFIG_CMD_EEPROM) += eeprom.ocmd/dtt.c deleted +0
-120@@ -1,120 +0,0 @@ -/* -* (C) Copyright 2001 -* Erik Theisen, Wave 7 Optics, etheisen at mindspring.com -* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -#include <common.h> -#include <config.h> -#include <command.h> - -#include <dtt.h> -#include <i2c.h> -#include <tmu.h> -#include <linux/bug.h> - -#if definedCONFIG_DTT_SENSORS -static unsigned long sensor_initialized; - -static void _initialize_dtt (void ) -{ -int i; -unsigned char sensors[] =CONFIG_DTT_SENSORS ; - -for (i =0 ; i <sizeof (sensors); i++) { -if ((sensor_initialized & (1 << i)) ==0 ) { -if (dtt_init_one (sensors[i]) !=0 ) { -printf ("DTT%d: Failed init!\n" , i); -continue ; - } - sensor_initialized |= (1 << i); - } - } -} - -void dtt_init (void ) -{ -int old_bus; - -/* switch to correct I2C bus */ - old_bus =I2C_GET_BUS (); -I2C_SET_BUS (CONFIG_SYS_DTT_BUS_NUM ); - -_initialize_dtt (); - -/* switch back to original I2C bus */ -I2C_SET_BUS (old_bus); -} -#endif - -int dtt_i2c (void ) -{ -#if definedCONFIG_DTT_SENSORS -int i; -unsigned char sensors[] =CONFIG_DTT_SENSORS ; -int old_bus; - -/* Force a compilation error, if there are more then 32 sensors */ -BUILD_BUG_ON (sizeof (sensors) >32 ); -/* switch to correct I2C bus */ -#ifdef CONFIG_SYS_I2C - old_bus =i2c_get_bus_num (); -i2c_set_bus_num (CONFIG_SYS_DTT_BUS_NUM ); -#else - old_bus =I2C_GET_BUS (); -I2C_SET_BUS (CONFIG_SYS_DTT_BUS_NUM ); -#endif - -_initialize_dtt (); - -/* -* Loop through sensors, read -* temperature, and output it. -*/ -for (i =0 ; i <sizeof (sensors); i++) -printf ("DTT%d: %i C\n" , i +1 ,dtt_get_temp (sensors[i])); - -/* switch back to original I2C bus */ -#ifdef CONFIG_SYS_I2C -i2c_set_bus_num (old_bus); -#else -I2C_SET_BUS (old_bus); -#endif -#endif - -return 0 ; -} - -int dtt_tmu (void ) -{ -#if definedCONFIG_TMU_CMD_DTT -int cur_temp; - -/* Sense and return latest thermal info */ -if (tmu_monitor (&cur_temp) ==TMU_STATUS_INIT ) { -puts ("TMU is in unknown state, temperature is invalid\n" ); -return -1 ; - } -printf ("Current temperature: %u degrees Celsius\n" , cur_temp); -#endif -return 0 ; -} - -int do_dtt (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) -{ -int err =0 ; - - err |=dtt_i2c (); - err |=dtt_tmu (); - -return err; -}/* do_dtt() */ - -/***************************************************/ - -U_BOOT_CMD ( - dtt,1 ,1 , do_dtt, -"Read temperature from Digital Thermometer and Thermostat" , -"" -);drivers/Kconfig +0
-2@@ -30,8 +30,6 @@ source "drivers/fpga/Kconfig" source "drivers/gpio/Kconfig" -source "drivers/hwmon/Kconfig" - source "drivers/i2c/Kconfig" source "drivers/input/Kconfig"drivers/Makefile +0
-1@@ -74,7 +74,6 @@ obj-$(CONFIG_CPU) += cpu/ obj-y += crypto/ obj-y += firmware/ obj-$(CONFIG_FPGA) += fpga/ -obj-y += hwmon/ obj-y += misc/ obj-y += pcmcia/ obj-y += dfu/drivers/hwmon/Kconfig deleted +0
-0drivers/hwmon/Makefile deleted +0
-22@@ -1,22 +0,0 @@ -# -# (C) Copyright 2006 -# Wolfgang Denk, DENX Software Engineering, wd at denx.de. -# -# (C) Copyright 2001 -# Erik Theisen, Wave 7 Optics, etheisen at mindspring.com. -# -# SPDX-License-Identifier: GPL-2.0+ -# - -#ccflags-y += -DDEBUG - -obj-$(CONFIG_DTT_ADM1021) += adm1021.o -obj-$(CONFIG_DTT_ADT7460) += adt7460.o -obj-$(CONFIG_DTT_DS1621) += ds1621.o -obj-$(CONFIG_DTT_DS1722) += ds1722.o -obj-$(CONFIG_DTT_DS1775) += ds1775.o -obj-$(CONFIG_DTT_DS620) += ds620.o -obj-$(CONFIG_DTT_LM63) += lm63.o -obj-$(CONFIG_DTT_LM73) += lm73.o -obj-$(CONFIG_DTT_LM75) += lm75.o -obj-$(CONFIG_DTT_LM81) += lm81.odrivers/hwmon/adm1021.c deleted +0
-164@@ -1,164 +0,0 @@ -/* -* (C) Copyright 2003 -* Murray Jensen, CSIRO-MIT, Murray.Jensen at csiro.au -* -* based on dtt/lm75.c which is ... -* -* (C) Copyright 2001 -* Bill Hunter, Wave 7 Optics, williamhunter at mediaone.net -* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -/* -* Analog Devices's ADM1021 -* "Low Cost Microprocessor System Temperature Monitor" -*/ - -#include <common.h> - -#include <i2c.h> -#include <dtt.h> - -#define DTT_READ_LOC_VALUE 0x00 -#define DTT_READ_REM_VALUE 0x01 -#define DTT_READ_STATUS 0x02 -#define DTT_READ_CONFIG 0x03 -#define DTT_READ_CONVRATE 0x04 -#define DTT_READ_LOC_HIGHLIM 0x05 -#define DTT_READ_LOC_LOWLIM 0x06 -#define DTT_READ_REM_HIGHLIM 0x07 -#define DTT_READ_REM_LOWLIM 0x08 -#define DTT_READ_DEVID 0xfe - -#define DTT_WRITE_CONFIG 0x09 -#define DTT_WRITE_CONVRATE 0x0a -#define DTT_WRITE_LOC_HIGHLIM 0x0b -#define DTT_WRITE_LOC_LOWLIM 0x0c -#define DTT_WRITE_REM_HIGHLIM 0x0d -#define DTT_WRITE_REM_LOWLIM 0x0e -#define DTT_WRITE_ONESHOT 0x0f - -#define DTT_STATUS_BUSY 0x80/* 1=ADC Converting */ -#define DTT_STATUS_LHIGH 0x40/* 1=Local High Temp Limit Tripped */ -#define DTT_STATUS_LLOW 0x20/* 1=Local Low Temp Limit Tripped */ -#define DTT_STATUS_RHIGH 0x10/* 1=Remote High Temp Limit Tripped */ -#define DTT_STATUS_RLOW 0x08/* 1=Remote Low Temp Limit Tripped */ -#define DTT_STATUS_OPEN 0x04/* 1=Remote Sensor Open-Circuit */ - -#define DTT_CONFIG_ALERT_MASKED 0x80/* 0=ALERT Enabled, 1=ALERT Masked */ -#define DTT_CONFIG_STANDBY 0x40/* 0=Run, 1=Standby */ - -#define DTT_ADM1021_DEVID 0x41 - -typedef -struct { -uint i2c_addr:7 ;/* 7bit i2c chip address */ -uint conv_rate:3 ;/* conversion rate */ -uint enable_alert:1 ;/* enable alert output pin */ -uint enable_local:1 ;/* enable internal temp sensor */ -uint max_local:8 ;/* internal temp maximum */ -uint min_local:8 ;/* internal temp minimum */ -uint enable_remote:1 ;/* enable remote temp sensor */ -uint max_remote:8 ;/* remote temp maximum */ -uint min_remote:8 ;/* remote temp minimum */ - } -dtt_cfg_t ; - -dtt_cfg_t dttcfg[] =CONFIG_SYS_DTT_ADM1021 ; - -int -dtt_read (int sensor,int reg) -{ -dtt_cfg_t *dcp = &dttcfg[sensor >>1 ]; -uchar data; - -if (i2c_read (dcp->i2c_addr, reg,1 , &data,1 ) !=0 ) -return -1 ; - -return (int )data; -}/* dtt_read() */ - -int -dtt_write (int sensor,int reg,int val) -{ -dtt_cfg_t *dcp = &dttcfg[sensor >>1 ]; -uchar data; - - data = (uchar)(val &0xff ); - -if (i2c_write (dcp->i2c_addr, reg,1 , &data,1 ) !=0 ) -return 1 ; - -return 0 ; -}/* dtt_write() */ - -int -dtt_init_one (int sensor) -{ -dtt_cfg_t *dcp = &dttcfg[sensor >>1 ]; -int reg, val; - -if (((sensor &1 ) ==0 ? dcp->enable_local : dcp->enable_remote) ==0 ) -return 1 ;/* sensor is disabled (or rather ignored) */ - -/* -* Setup High Limit register -*/ -if ((sensor &1 ) ==0 ) { - reg =DTT_WRITE_LOC_HIGHLIM ; - val = dcp->max_local; - } -else { - reg =DTT_WRITE_REM_HIGHLIM ; - val = dcp->max_remote; - } -if (dtt_write (sensor, reg, val) !=0 ) -return 1 ; - -/* -* Setup Low Limit register -*/ -if ((sensor &1 ) ==0 ) { - reg =DTT_WRITE_LOC_LOWLIM ; - val = dcp->min_local; - } -else { - reg =DTT_WRITE_REM_LOWLIM ; - val = dcp->min_remote; - } -if (dtt_write (sensor, reg, val) !=0 ) -return 1 ; - -/* shouldn't hurt if the rest gets done twice */ - -/* -* Setup Conversion Rate register -*/ -if (dtt_write (sensor,DTT_WRITE_CONVRATE , dcp->conv_rate) !=0 ) -return 1 ; - -/* -* Setup configuraton register -*/ - val =0 ;/* running */ -if (dcp->enable_alert ==0 ) - val |=DTT_CONFIG_ALERT_MASKED ;/* mask ALERT pin */ -if (dtt_write (sensor,DTT_WRITE_CONFIG , val) !=0 ) -return 1 ; - -return 0 ; -}/* dtt_init_one() */ - -int -dtt_get_temp (int sensor) -{ -signed char val; - -if ((sensor &1 ) ==0 ) - val =dtt_read (sensor,DTT_READ_LOC_VALUE ); -else - val =dtt_read (sensor,DTT_READ_REM_VALUE ); - -return (int ) val; -}/* dtt_get_temp() */ drivers/hwmon/adt7460.c deleted +0
-73@@ -1,73 +0,0 @@ -/* -* (C) Copyright 2008 -* Ricado Ribalda-Universidad Autonoma de Madrid, ricardo.ribalda at gmail.com -* This work has been supported by: QTechnology http://qtec.com/ -* SPDX-License-Identifier: GPL-2.0+ -*/ - -#include <common.h> -#include <i2c.h> -#include <dtt.h> - -#define ADT7460_ADDRESS 0x2c -#define ADT7460_INVALID 128 -#define ADT7460_CONFIG 0x40 -#define ADT7460_REM1_TEMP 0x25 -#define ADT7460_LOCAL_TEMP 0x26 -#define ADT7460_REM2_TEMP 0x27 - -int dtt_read (int sensor,int reg) -{ -u8 dir = reg; -u8 data; - -if (i2c_read (ADT7460_ADDRESS , dir,1 , &data,1 ) ==-1 ) -return -1 ; -if (data ==ADT7460_INVALID ) -return -1 ; - -return data; -} - -int dtt_write (int sensor,int reg,int val) -{ -u8 dir = reg; -u8 data = val; - -if (i2c_write (ADT7460_ADDRESS , dir,1 , &data,1 ) ==-1 ) -return -1 ; - -return 0 ; -} - -int dtt_init_one (int sensor) -{ -printf ("ADT7460 at I2C address 0x%2x\n" ,ADT7460_ADDRESS ); - -if (dtt_write (0 ,ADT7460_CONFIG ,1 ) ==-1 ) { -puts ("Error initialiting ADT7460\n" ); -return -1 ; - } - -return 0 ; -} - -int dtt_get_temp (int sensor) -{ -int aux; -u8 table[] = - {ADT7460_REM1_TEMP ,ADT7460_LOCAL_TEMP ,ADT7460_REM2_TEMP }; - -if (sensor >2 ) { -puts ("DTT sensor does not exist\n" ); -return -1 ; - } - - aux =dtt_read (0 , table[sensor]); -if (aux ==-1 ) { -puts ("DTT temperature read failed\n" ); -return -1 ; - } - -return aux; -}drivers/hwmon/ds1621.c deleted +0
-155@@ -1,155 +0,0 @@ -/* -* (C) Copyright 2001 -* Erik Theisen, Wave 7 Optics, etheisen at mindspring.com. -* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -/* -* Dallas Semiconductor's DS1621/1631 Digital Thermometer and Thermostat. -*/ - -#include <common.h> -#include <i2c.h> -#include <dtt.h> - -/* -* Device code -*/ -#define DTT_I2C_DEV_CODE 0x48/* Dallas Semi's DS1621 */ -#define DTT_READ_TEMP 0xAA -#define DTT_READ_COUNTER 0xA8 -#define DTT_READ_SLOPE 0xA9 -#define DTT_WRITE_START_CONV 0xEE -#define DTT_WRITE_STOP_CONV 0x22 -#define DTT_TEMP_HIGH 0xA1 -#define DTT_TEMP_LOW 0xA2 -#define DTT_CONFIG 0xAC - -/* -* Config register bits -*/ -#define DTT_CONFIG_1SHOT 0x01 -#define DTT_CONFIG_POLARITY 0x02 -#define DTT_CONFIG_R0 0x04/* ds1631 only */ -#define DTT_CONFIG_R1 0x08/* ds1631 only */ -#define DTT_CONFIG_NVB 0x10 -#define DTT_CONFIG_TLF 0x20 -#define DTT_CONFIG_THF 0x40 -#define DTT_CONFIG_DONE 0x80 - - -int dtt_read (int sensor,int reg) -{ -int dlen; -uchar data[2 ]; - -/* Calculate sensor address and command */ - sensor =DTT_I2C_DEV_CODE + (sensor &0x07 );/* Calculate addr of ds1621*/ - -/* Prepare to handle 2 byte result */ -switch (reg) { -case DTT_READ_TEMP : -case DTT_TEMP_HIGH : -case DTT_TEMP_LOW : - dlen =2 ; -break ; -default : - dlen =1 ; - } - -/* Now try to read the register */ -if (i2c_read (sensor, reg,1 , data, dlen) !=0 ) -return 1 ; - -/* Handle 2 byte result */ -if (dlen ==2 ) -return (short )((data[0 ] <<8 ) | data[1 ]); - -return (int )data[0 ]; -} - - -int dtt_write (int sensor,int reg,int val) -{ -int dlen; -uchar data[2 ]; - -/* Calculate sensor address and register */ - sensor =DTT_I2C_DEV_CODE + (sensor &0x07 ); - -/* Handle various data sizes. */ -switch (reg) { -case DTT_READ_TEMP : -case DTT_TEMP_HIGH : -case DTT_TEMP_LOW : - dlen =2 ; - data[0 ] = (char )((val >>8 ) &0xff );/* MSB first */ - data[1 ] = (char )(val &0xff ); -break ; -case DTT_WRITE_START_CONV : -case DTT_WRITE_STOP_CONV : - dlen =0 ; - data[0 ] = (char )0 ; - data[1 ] = (char )0 ; -break ; -default : - dlen =1 ; - data[0 ] = (char )(val &0xff ); - } - -/* Write value to device */ -if (i2c_write (sensor, reg,1 , data, dlen) !=0 ) -return 1 ; - -/* Poll NV memory busy bit in case write was to register stored in EEPROM */ -while (i2c_reg_read (sensor,DTT_CONFIG ) &DTT_CONFIG_NVB ) - ; - -return 0 ; -} - - -int dtt_init_one (int sensor) -{ -int val; - -/* Setup High Temp */ - val = ((CONFIG_SYS_DTT_MAX_TEMP *2 ) <<7 ) &0xff80 ; -if (dtt_write (sensor,DTT_TEMP_HIGH , val) !=0 ) -return 1 ; - -/* Setup Low Temp - hysteresis */ - val = (((CONFIG_SYS_DTT_MAX_TEMP -CONFIG_SYS_DTT_HYSTERESIS ) *2 ) <<7 ) &0xff80 ; -if (dtt_write (sensor,DTT_TEMP_LOW , val) !=0 ) -return 1 ; - -/* -* Setup configuraton register -* -* Clear THF & TLF, Reserved = 1, Polarity = Active Low, One Shot = YES -* -* We run in polled mode, since there isn't any way to know if this -* lousy device is ready to provide temperature readings on power up. -*/ - val =0x9 ; -if (dtt_write (sensor,DTT_CONFIG , val) !=0 ) -return 1 ; - -return 0 ; -} - -int dtt_get_temp (int sensor) -{ -int i; - -/* Start a conversion, may take up to 1 second. */ -dtt_write (sensor,DTT_WRITE_START_CONV ,0 ); -for (i =0 ; i <=10 ; i++) { -udelay (100000 ); -if (dtt_read (sensor,DTT_CONFIG ) &DTT_CONFIG_DONE ) -break ; - } - -return (dtt_read (sensor,DTT_READ_TEMP ) /256 ); -}drivers/hwmon/ds1722.c deleted +0
-137@@ -1,137 +0,0 @@ -#include <common.h> -#include <asm/ic/ssi.h> -#include <ds1722.h> - -static void ds1722_select (int dev) -{ -ssi_set_interface (4096 ,0 ,0 ,0 ); -ssi_chip_select (0 ); -udelay (1 ); -ssi_chip_select (dev); -udelay (1 ); -} - - -u8 ds1722_read (int dev,int addr) -{ -u8 res; - -ds1722_select (dev); - -ssi_tx_byte (addr); - res =ssi_rx_byte (); - -ssi_chip_select (0 ); - -return res; -} - -void ds1722_write (int dev,int addr,u8 data) -{ -ds1722_select (dev); - -ssi_tx_byte (0x80 |addr); -ssi_tx_byte (data); - -ssi_chip_select (0 ); -} - - -u16 ds1722_temp (int dev,int resolution) -{ -static int useconds[] = { -75000 ,150000 ,300000 ,600000 ,1200000 - }; -char temp; -u16 res; - - -/* set up the desired resulotion ... */ -ds1722_write (dev,0 ,0xe0 | (resolution <<1 )); - -/* wait while the chip measures the tremperature */ -udelay (useconds[resolution]); - - res = (temp =ds1722_read (dev,2 )) <<8 ; - -if (temp <0 ) { - temp = (16 - (ds1722_read (dev,1 ) >>4 )) &0x0f ; - }else { - temp = (ds1722_read (dev,1 ) >>4 ); - } - -switch (temp) { -case 0 : -/* .0000 */ -break ; -case 1 : -/* .0625 */ - res |=1 ; -break ; -case 2 : -/* .1250 */ - res |=1 ; -break ; -case 3 : -/* .1875 */ - res |=2 ; -break ; -case 4 : -/* .2500 */ - res |=3 ; -break ; -case 5 : -/* .3125 */ - res |=3 ; -break ; -case 6 : -/* .3750 */ - res |=4 ; -break ; -case 7 : -/* .4375 */ - res |=4 ; -break ; -case 8 : -/* .5000 */ - res |=5 ; -break ; -case 9 : -/* .5625 */ - res |=6 ; -break ; -case 10 : -/* .6250 */ - res |=6 ; -break ; -case 11 : -/* .6875 */ - res |=7 ; -break ; -case 12 : -/* .7500 */ - res |=8 ; -break ; -case 13 : -/* .8125 */ - res |=8 ; -break ; -case 14 : -/* .8750 */ - res |=9 ; -break ; -case 15 : -/* .9375 */ - res |=9 ; -break ; - } -return res; - -} - -int ds1722_probe (int dev) -{ -u16 temp =ds1722_temp (dev,DS1722_RESOLUTION_12BIT ); -printf ("%d.%d deg C\n\n" , (char )(temp >>8 ), temp &0xff ); -return 0 ; -}drivers/hwmon/ds1775.c deleted +0
-126@@ -1,126 +0,0 @@ -/* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -/* -* Dallas Semiconductor's DS1775 Digital Thermometer and Thermostat -*/ - -#include <common.h> - -#include <i2c.h> -#include <dtt.h> - -#define DTT_I2C_DEV_CODE 0x48/* Dallas Semi's DS1775 device code */ -#define DTT_READ_TEMP 0x0 -#define DTT_CONFIG 0x1 -#define DTT_TEMP_HYST 0x2 -#define DTT_TEMP_OS 0x3 - -int dtt_read (int sensor,int reg) -{ -int dlen; -uchar data[2 ]; - -/* -* Calculate sensor address and command -*/ - sensor =DTT_I2C_DEV_CODE + (sensor &0x07 );/* Calculate addr of ds1775 */ - -/* -* Prepare to handle 2 byte result -*/ -if ((reg ==DTT_READ_TEMP ) || - (reg ==DTT_TEMP_OS ) || (reg ==DTT_TEMP_HYST )) - dlen =2 ; -else - dlen =1 ; - -/* -* Now try to read the register -*/ -if (i2c_read (sensor, reg,1 , data, dlen) !=0 ) -return 1 ; - -/* -* Handle 2 byte result -*/ -if (dlen ==2 ) -return ((int )((short )data[1 ] + (((short )data[0 ]) <<8 ))); - -return (int ) data[0 ]; -} - - -int dtt_write (int sensor,int reg,int val) -{ -int dlen; -uchar data[2 ]; - -/* -* Calculate sensor address and register -*/ - sensor =DTT_I2C_DEV_CODE + (sensor &0x07 ); - -/* -* Handle various data sizes -*/ -if ((reg ==DTT_READ_TEMP ) || - (reg ==DTT_TEMP_OS ) || (reg ==DTT_TEMP_HYST )) { - dlen =2 ; - data[0 ] = (char )((val >>8 ) &0xff );/* MSB first */ - data[1 ] = (char )(val &0xff ); - }else { - dlen =1 ; - data[0 ] = (char )(val &0xff ); - } - -/* -* Write value to device -*/ -if (i2c_write (sensor, reg,1 , data, dlen) !=0 ) -return 1 ; - -return 0 ; -} - - -int dtt_init_one (int sensor) -{ -int val; - -/* -* Setup High Temp -*/ - val = ((CONFIG_SYS_DTT_MAX_TEMP *2 ) <<7 ) &0xff80 ; -if (dtt_write (sensor,DTT_TEMP_OS , val) !=0 ) -return 1 ; -udelay (50000 );/* Max 50ms */ - -/* -* Setup Low Temp - hysteresis -*/ - val = (((CONFIG_SYS_DTT_MAX_TEMP -CONFIG_SYS_DTT_HYSTERESIS ) *2 ) <<7 ) &0xff80 ; -if (dtt_write (sensor,DTT_TEMP_HYST , val) !=0 ) -return 1 ; -udelay (50000 );/* Max 50ms */ - -/* -* Setup configuraton register -* -* Fault Tolerance limits 4, Thermometer resolution bits is 9, -* Polarity = Active Low,continuous conversion mode, Thermostat -* mode is interrupt mode -*/ - val =0xa ; -if (dtt_write (sensor,DTT_CONFIG , val) !=0 ) -return 1 ; -udelay (50000 );/* Max 50ms */ - -return 0 ; -} - -int dtt_get_temp (int sensor) -{ -return (dtt_read (sensor,DTT_READ_TEMP ) /256 ); -}drivers/hwmon/ds620.c deleted +0
-65@@ -1,65 +0,0 @@ -/* -* DS620 DTT support -* -* (C) Copyright 2014 3ADEV <http://www.3adev.com> -* Written-by: Albert ARIBAUD <[email protected]> -* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -/* -* Dallas Semiconductor's DS1621/1631 Digital Thermometer and Thermostat. -*/ - -#include <common.h> -#include <i2c.h> -#include <dtt.h> - -/* -* Device code -*/ -#define DTT_I2C_DEV_CODE 0x48 -#define DTT_START_CONVERT 0x51 -#define DTT_TEMP 0xAA -#define DTT_CONFIG 0xAC - -/* -* Config register MSB bits -*/ -#define DTT_CONFIG_1SHOT 0x01 -#define DTT_CONFIG_AUTOC 0x02 -#define DTT_CONFIG_R0 0x04/* always 1 */ -#define DTT_CONFIG_R1 0x08/* always 1 */ -#define DTT_CONFIG_TLF 0x10 -#define DTT_CONFIG_THF 0x20 -#define DTT_CONFIG_NVB 0x40 -#define DTT_CONFIG_DONE 0x80 - -#define CHIP (sensor) (DTT_I2C_DEV_CODE + (sensor & 0x07)) - -int dtt_init_one (int sensor) -{ -uint8_t config =DTT_CONFIG_1SHOT - |DTT_CONFIG_R0 - |DTT_CONFIG_R1 ; -return i2c_write (CHIP (sensor),DTT_CONFIG ,1 , &config,1 ); -} - -int dtt_get_temp (int sensor) -{ -uint8_t status; -uint8_t temp[2 ]; - -/* Start a conversion, may take up to 1 second. */ -i2c_write (CHIP (sensor),DTT_START_CONVERT ,1 ,NULL ,0 ); -do { -if (i2c_read (CHIP (sensor),DTT_CONFIG ,1 , &status,1 )) -/* bail out if I2C error */ - status |=DTT_CONFIG_DONE ; - }while (!(status &DTT_CONFIG_DONE )); -if (i2c_read (CHIP (sensor),DTT_TEMP ,1 , temp,2 )) -/* bail out if I2C error */ -return -274 ;/* below absolute zero == error */ - -return ((int16_t )(temp[1 ] | (temp[0 ] <<8 ))) >>7 ; -}drivers/hwmon/lm63.c deleted +0
-160@@ -1,160 +0,0 @@ -/* -* (C) Copyright 2007-2008 -* Dirk Eibach, Guntermann & Drunck GmbH, eibach at gdsys.de -* based on lm75.c by Bill Hunter -* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -/* -* National LM63/LM64 Temperature Sensor -* Main difference: LM 64 has -16 Kelvin temperature offset -*/ - -#include <common.h> -#include <i2c.h> -#include <dtt.h> - -#define DTT_I2C_LM63_ADDR 0x4C/* National LM63 device */ - -#define DTT_READ_TEMP_RMT_MSB 0x01 -#define DTT_CONFIG 0x03 -#define DTT_READ_TEMP_RMT_LSB 0x10 -#define DTT_TACHLIM_LSB 0x48 -#define DTT_TACHLIM_MSB 0x49 -#define DTT_FAN_CONFIG 0x4A -#define DTT_PWM_FREQ 0x4D -#define DTT_PWM_LOOKUP_BASE 0x50 - -struct pwm_lookup_entry { -u8 temp; -u8 pwm; -}; - -/* -* Device code -*/ - -int dtt_read (int sensor,int reg) -{ -int dlen; -uchar data[2 ]; - -/* -* Calculate sensor address and register. -*/ -if (!sensor) - sensor =DTT_I2C_LM63_ADDR ;/* legacy config */ - - dlen =1 ; - -/* -* Now try to read the register. -*/ -if (i2c_read (sensor, reg,1 , data, dlen) !=0 ) -return -1 ; - -return (int )data[0 ]; -}/* dtt_read() */ - -int dtt_write (int sensor,int reg,int val) -{ -int dlen; -uchar data[2 ]; - -/* -* Calculate sensor address and register. -*/ -if (!sensor) - sensor =DTT_I2C_LM63_ADDR ;/* legacy config */ - - dlen =1 ; - data[0 ] = (char )(val &0xff ); - -/* -* Write value to register. -*/ -if (i2c_write (sensor, reg,1 , data, dlen) !=0 ) -return 1 ; - -return 0 ; -}/* dtt_write() */ - -static int is_lm64 (int sensor) -{ -return sensor && (sensor !=DTT_I2C_LM63_ADDR ); -} - -int dtt_init_one (int sensor) -{ -int i; -int val; - -struct pwm_lookup_entry pwm_lookup[] =CONFIG_DTT_PWM_LOOKUPTABLE ; - -/* -* Set PWM Frequency to 2.5% resolution -*/ - val =20 ; -if (dtt_write (sensor,DTT_PWM_FREQ , val) !=0 ) -return 1 ; - -/* -* Set Tachometer Limit -*/ - val =CONFIG_DTT_TACH_LIMIT ; -if (dtt_write (sensor,DTT_TACHLIM_LSB , val &0xff ) !=0 ) -return 1 ; -if (dtt_write (sensor,DTT_TACHLIM_MSB , (val >>8 ) &0xff ) !=0 ) -return 1 ; - -/* -* Make sure PWM Lookup-Table is writeable -*/ -if (dtt_write (sensor,DTT_FAN_CONFIG ,0x20 ) !=0 ) -return 1 ; - -/* -* Setup PWM Lookup-Table -*/ -for (i =0 ; i <ARRAY_SIZE (pwm_lookup); i++) { -int address =DTT_PWM_LOOKUP_BASE +2 * i; - val = pwm_lookup[i].temp; -if (is_lm64 (sensor)) - val -=16 ; -if (dtt_write (sensor, address, val) !=0 ) -return 1 ; - val =dtt_read (sensor, address); - val = pwm_lookup[i].pwm; -if (dtt_write (sensor, address +1 , val) !=0 ) -return 1 ; - } - -/* -* Enable PWM Lookup-Table, PWM Clock 360 kHz, Tachometer Mode 2 -*/ - val =0x02 ; -if (dtt_write (sensor,DTT_FAN_CONFIG , val) !=0 ) -return 1 ; - -/* -* Enable Tach input -*/ - val =dtt_read (sensor,DTT_CONFIG ) |0x04 ; -if (dtt_write (sensor,DTT_CONFIG , val) !=0 ) -return 1 ; - -return 0 ; -} - -int dtt_get_temp (int sensor) -{ -s16 temp = (dtt_read (sensor,DTT_READ_TEMP_RMT_MSB ) <<8 ) - | (dtt_read (sensor,DTT_READ_TEMP_RMT_LSB )); - -if (is_lm64 (sensor)) - temp +=16 <<8 ; - -/* Ignore LSB for now, U-Boot only prints natural numbers */ -return temp >>8 ; -}drivers/hwmon/lm73.c deleted +0
-146@@ -1,146 +0,0 @@ -/* -* (C) Copyright 2007-2008 -* Larry Johnson, lrj at acm.org -* -* based on dtt/lm75.c which is ... -* -* (C) Copyright 2001 -* Bill Hunter, Wave 7 Optics, williamhunter at mediaone.net -* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -/* -* National Semiconductor LM73 Temperature Sensor -*/ - -#include <common.h> -#include <i2c.h> -#include <dtt.h> - -/* -* Device code -*/ -#define DTT_I2C_DEV_CODE 0x48/* National Semi's LM73 device */ -#define DTT_READ_TEMP 0x0 -#define DTT_CONFIG 0x1 -#define DTT_TEMP_HIGH 0x2 -#define DTT_TEMP_LOW 0x3 -#define DTT_CONTROL 0x4 -#define DTT_ID 0x7 - -int dtt_read (int const sensor,int const reg) -{ -int dlen; -uint8_t data[2 ]; - -/* -* Validate 'reg' param and get register size. -*/ -switch (reg) { -case DTT_CONFIG : -case DTT_CONTROL : - dlen =1 ; -break ; -case DTT_READ_TEMP : -case DTT_TEMP_HIGH : -case DTT_TEMP_LOW : -case DTT_ID : - dlen =2 ; -break ; -default : -return -1 ; - } -/* -* Try to read the register at the calculated sensor address. -*/ -if (0 != -i2c_read (DTT_I2C_DEV_CODE + (sensor &0x07 ), reg,1 , data, dlen)) -return -1 ; -/* -* Handle 2 byte result. -*/ -if (2 == dlen) -return (int )((unsigned )data[0 ] <<8 | (unsigned )data[1 ]); - -return (int )data[0 ]; -}/* dtt_read() */ - -int dtt_write (int const sensor,int const reg,int const val) -{ -int dlen; -uint8_t data[2 ]; - -/* -* Validate 'reg' param and handle register size -*/ -switch (reg) { -case DTT_CONFIG : -case DTT_CONTROL : - dlen =1 ; - data[0 ] = (uint8_t ) val; -break ; -case DTT_TEMP_HIGH : -case DTT_TEMP_LOW : - dlen =2 ; - data[0 ] = (uint8_t ) (val >>8 );/* MSB first */ - data[1 ] = (uint8_t ) val; -break ; -default : -return -1 ; - } -/* -* Write value to register at the calculated sensor address. -*/ -return 0 !=i2c_write (DTT_I2C_DEV_CODE + (sensor &0x07 ), reg,1 , data, - dlen); -}/* dtt_write() */ - -int dtt_init_one (int const sensor) -{ -int val; - -/* -* Validate the Identification register -*/ -if (0x0190 !=dtt_read (sensor,DTT_ID )) -return -1 ; -/* -* Setup THIGH (upper-limit) and TLOW (lower-limit) registers -*/ - val =CONFIG_SYS_DTT_MAX_TEMP <<7 ; -if (dtt_write (sensor,DTT_TEMP_HIGH , val)) -return -1 ; - - val =CONFIG_SYS_DTT_MIN_TEMP <<7 ; -if (dtt_write (sensor,DTT_TEMP_LOW , val)) -return -1 ; -/* -* Setup configuraton register -*/ -/* config = alert active low, disabled, and reset */ - val =0x64 ; -if (dtt_write (sensor,DTT_CONFIG , val)) -return -1 ; -/* -* Setup control/status register -*/ -/* control = temp resolution 0.25C */ - val =0x00 ; -if (dtt_write (sensor,DTT_CONTROL , val)) -return -1 ; - -dtt_read (sensor,DTT_CONTROL );/* clear temperature flags */ -return 0 ; -}/* dtt_init_one() */ - -int dtt_get_temp (int const sensor) -{ -int const ret =dtt_read (sensor,DTT_READ_TEMP ); - -if (ret <0 ) { -printf ("DTT temperature read failed.\n" ); -return 0 ; - } -return (int )((int16_t ) ret +0x0040 ) >>7 ; -}/* dtt_get_temp() */ drivers/hwmon/lm75.c deleted +0
-139@@ -1,139 +0,0 @@ -/* -* (C) Copyright 2001 -* Bill Hunter, Wave 7 Optics, williamhunter at mediaone.net -* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -/* -* On Semiconductor's LM75 Temperature Sensor -*/ - -#include <common.h> -#include <i2c.h> -#include <dtt.h> - -/* -* Device code -*/ -#define DTT_I2C_DEV_CODE 0x48/* ON Semi's LM75 device */ -#define DTT_READ_TEMP 0x0 -#define DTT_CONFIG 0x1 -#define DTT_TEMP_HYST 0x2 -#define DTT_TEMP_SET 0x3 - -int dtt_read (int sensor,int reg) -{ -int dlen; -uchar data[2 ]; - -#ifdef CONFIG_DTT_AD7414 -/* -* On AD7414 the first value upon bootup is not read correctly. -* This is most likely because of the 800ms update time of the -* temp register in normal update mode. To get current values -* each time we issue the "dtt" command including upon powerup -* we switch into one-short mode. -* -* Issue one-shot mode command -*/ -dtt_write (sensor,DTT_CONFIG ,0x64 ); -#endif - -/* Validate 'reg' param */ -if ((reg <0 ) || (reg >3 )) -return -1 ; - -/* Calculate sensor address and register. */ - sensor =DTT_I2C_DEV_CODE + (sensor &0x07 ); - -/* Prepare to handle 2 byte result. */ -if ((reg ==DTT_READ_TEMP ) || - (reg ==DTT_TEMP_HYST ) || - (reg ==DTT_TEMP_SET )) - dlen =2 ; -else - dlen =1 ; - -/* Now try to read the register. */ -if (i2c_read (sensor, reg,1 , data, dlen) !=0 ) -return -1 ; - -/* Handle 2 byte result. */ -if (dlen ==2 ) -return ((int )((short )data[1 ] + (((short )data[0 ]) <<8 ))); - -return (int )data[0 ]; -}/* dtt_read() */ - - -int dtt_write (int sensor,int reg,int val) -{ -int dlen; -uchar data[2 ]; - -/* Validate 'reg' param */ -if ((reg <0 ) || (reg >3 )) -return 1 ; - -/* Calculate sensor address and register. */ - sensor =DTT_I2C_DEV_CODE + (sensor &0x07 ); - -/* Handle 2 byte values. */ -if ((reg ==DTT_READ_TEMP ) || - (reg ==DTT_TEMP_HYST ) || - (reg ==DTT_TEMP_SET )) { - dlen =2 ; - data[0 ] = (char )((val >>8 ) &0xff );/* MSB first */ - data[1 ] = (char )(val &0xff ); - }else { - dlen =1 ; - data[0 ] = (char )(val &0xff ); - } - -/* Write value to register. */ -if (i2c_write (sensor, reg,1 , data, dlen) !=0 ) -return 1 ; - -return 0 ; -}/* dtt_write() */ - - -int dtt_init_one (int sensor) -{ -int val; - -/* Setup TSET ( trip point ) register */ - val = ((CONFIG_SYS_DTT_MAX_TEMP *2 ) <<7 ) &0xff80 ;/* trip */ -if (dtt_write (sensor,DTT_TEMP_SET , val) !=0 ) -return 1 ; - -/* Setup THYST ( untrip point ) register - Hysteresis */ - val = (((CONFIG_SYS_DTT_MAX_TEMP -CONFIG_SYS_DTT_HYSTERESIS ) *2 ) <<7 ) &0xff80 ; -if (dtt_write (sensor,DTT_TEMP_HYST , val) !=0 ) -return 1 ; - -/* Setup configuraton register */ -#ifdef CONFIG_DTT_AD7414 -/* config = alert active low and disabled */ - val =0x60 ; -#else -/* config = 6 sample integration, int mode, active low, and enable */ - val =0x18 ; -#endif -if (dtt_write (sensor,DTT_CONFIG , val) !=0 ) -return 1 ; - -return 0 ; -}/* dtt_init_one() */ - -int dtt_get_temp (int sensor) -{ -int const ret =dtt_read (sensor,DTT_READ_TEMP ); - -if (ret <0 ) { -printf ("DTT temperature read failed.\n" ); -return 0 ; - } -return (int )((int16_t ) ret /256 ); -}/* dtt_get_temp() */ drivers/hwmon/lm81.c deleted +0
-111@@ -1,111 +0,0 @@ -/* -* (C) Copyright 2006 -* Heiko Schocher, DENX Software Enginnering <[email protected]> -* -* based on dtt/lm75.c which is ... -* -* (C) Copyright 2001 -* Bill Hunter, Wave 7 Optics, williamhunter at mediaone.net -* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -/* -* On Semiconductor's LM81 Temperature Sensor -*/ - -#include <common.h> -#include <i2c.h> -#include <dtt.h> - -/* -* Device code -*/ -#define DTT_I2C_DEV_CODE 0x2c/* ON Semi's LM81 device */ -#define DTT_READ_TEMP 0x27 -#define DTT_CONFIG_TEMP 0x4b -#define DTT_TEMP_MAX 0x39 -#define DTT_TEMP_HYST 0x3a -#define DTT_CONFIG 0x40 - -int dtt_read (int sensor,int reg) -{ -int dlen =1 ; -uchar data[2 ]; - -/* -* Calculate sensor address and register. -*/ - sensor =DTT_I2C_DEV_CODE + (sensor &0x03 );/* calculate address of lm81 */ - -/* -* Now try to read the register. -*/ -if (i2c_read (sensor, reg,1 , data, dlen) !=0 ) -return -1 ; - -return (int )data[0 ]; -}/* dtt_read() */ - - -int dtt_write (int sensor,int reg,int val) -{ -uchar data; - -/* -* Calculate sensor address and register. -*/ - sensor =DTT_I2C_DEV_CODE + (sensor &0x03 );/* calculate address of lm81 */ - - data = (char )(val &0xff ); - -/* -* Write value to register. -*/ -if (i2c_write (sensor, reg,1 , &data,1 ) !=0 ) -return 1 ; - -return 0 ; -}/* dtt_write() */ - -#define DTT_MANU 0x3e -#define DTT_REV 0x3f -#define DTT_CONFIG 0x40 -#define DTT_ADR 0x48 - -int dtt_init_one (int sensor) -{ -int man; -int adr; -int rev; - -if (dtt_write (sensor,DTT_CONFIG ,0x01 ) <0 ) -return 1 ; -/* The LM81 needs 400ms to get the correct values ... */ -udelay (400000 ); - man =dtt_read (sensor,DTT_MANU ); -if (man !=0x01 ) -return 1 ; - adr =dtt_read (sensor,DTT_ADR ); -if (adr <0 ) -return 1 ; - rev =dtt_read (sensor,DTT_REV ); -if (rev <0 ) -return 1 ; - -debug ("DTT: Found LM81@%x Rev: %d\n" , adr, rev); -return 0 ; -}/* dtt_init_one() */ - - -#define TEMP_FROM_REG (temp) \ - ((temp)<256?((((temp)&0x1fe) >> 1) * 10) + ((temp) & 1) * 5: \ - ((((temp)&0x1fe) >> 1) -255) * 10 - ((temp) & 1) * 5) \ - -int dtt_get_temp (int sensor) -{ -int val =dtt_read (sensor,DTT_READ_TEMP ); -int tmpcnf =dtt_read (sensor,DTT_CONFIG_TEMP ); - -return (TEMP_FROM_REG ((val <<1 ) + ((tmpcnf &0x80 ) >>7 ))) /10 ; -}/* dtt_get_temp() */ include/config_cmd_all.h +0
-1@@ -13,7 +13,6 @@* Alphabetical list of all possible commands. */ -#define CONFIG_CMD_DTT /* Digital Therm and Thermostat */ #define CONFIG_CMD_EEPROM /* EEPROM read/write support */ #define CONFIG_CMD_FDC /* Floppy Disk Support */ #define CONFIG_CMD_FUSE /* Device fuse support */ include/configs/PMC440.h +0
-21@@ -163,26 +163,6 @@#define CONFIG_SYS_EEPROM_WREN 1#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52 -/* -* standard dtt sensor configuration - bottom bit will determine local or -* remote sensor of the TMP401 -*/ -#define CONFIG_DTT_SENSORS { 0, 1 } - -/* -* The PMC440 uses a TI TMP401 temperature sensor. This part -* is basically compatible to the ADM1021 that is supported -* by U-Boot. -* -* - i2c addr 0x4c -* - conversion rate 0x02 = 0.25 conversions/second -* - ALERT ouput disabled -* - local temp sensor enabled, min set to 0 deg, max set to 70 deg -* - remote temp sensor enabled, min set to 0 deg, max set to 70 deg -*/ -#define CONFIG_DTT_ADM1021 -#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} } -#define CONFIG_PREBOOT "echo Add \\\"run fpga\\\" and " \ "\\\"painit\\\" to preboot command"@@ -258,7 +238,6 @@/* Partitions */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI include/configs/TQM834x.h +0
-8@@ -184,13 +184,6 @@#define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */ #define CONFIG_SYS_I2C_RTC_ADDR 0x68/* at address 0x68 */ -/* I2C SYSMON (LM75) */ -#define CONFIG_DTT_LM75 1/* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -/* * TSEC */ @@ -280,7 +273,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO include/configs/UCP1020.h +0
-21@@ -129,27 +129,6 @@#define CONFIG_HWCONFIG -#define CONFIG_DTT_ADM1021 1/* ADM1021 temp sensor support */ -#define CONFIG_SYS_DTT_BUS_NUM 1/* The I2C bus for DTT */ -#define CONFIG_DTT_SENSORS { 0, 1 }/* Sensor index */ -/* -* ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details). -* there will be one entry in this array for each two (dummy) sensors in -* CONFIG_DTT_SENSORS. -* -* For uCP1020 module: -* - only one ADM1021/NCT72 -* - i2c addr 0x41 -* - conversion rate 0x02 = 0.25 conversions/second -* - ALERT output disabled -* - local temp sensor enabled, min set to 0 deg, max set to 85 deg -* - remote temp sensor enabled, min set to 0 deg, max set to 85 deg -*/ -#define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \ - 0x02, 0, 1, 0, 85, 1, 0, 85} } - -#define CONFIG_CMD_DTT -/* * These can be toggled for performance analysis, otherwise use default. */ include/configs/acadia.h +0
-9@@ -124,14 +124,6 @@#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1/* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 1/* use AD7414 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -/*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/ @@ -160,7 +152,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND /*----------------------------------------------------------------------- include/configs/canyonlands.h +0
-11@@ -261,14 +261,6 @@#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 /* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 /* use AD7414 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -#if !defined(CONFIG_ARCHES )/* RTC configuration */ #define CONFIG_RTC_M41T62 @@ -369,17 +361,14 @@* Commands additional to the ones defined in amcc-common.h */ #if defined(CONFIG_ARCHES ) -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM #elif defined(CONFIG_CANYONLANDS ) -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SATA #define CONFIG_CMD_SDRAM #elif defined(CONFIG_GLACIER ) -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM include/configs/dlvision-10g.h +0
-8@@ -57,7 +57,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ@@ -111,13 +110,6 @@#define CONFIG_SYS_SPD_BUS_NUM 4/* Temp sensor/hwmon/dtt */ -#define CONFIG_SYS_DTT_BUS_NUM 4 -#define CONFIG_DTT_LM63 1/* National LM63 */ -#define CONFIG_DTT_SENSORS { 0x4c, 0x4e, 0x18 }/* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 46, 10 }, { 48, 14 }, { 50, 19 }, { 52, 23 },\ - { 54, 27 }, { 56, 31 }, { 58, 36 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10#define CONFIG_SYS_ICS8N3QV01_I2C {1, 3}#define CONFIG_SYS_SIL1178_I2C {0, 2}include/configs/dlvision.h +0
-1@@ -55,7 +55,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQinclude/configs/exynos5-common.h +0
-2@@ -46,8 +46,6 @@/* Thermal Management Unit */ #define CONFIG_EXYNOS_TMU -#define CONFIG_CMD_DTT -#define CONFIG_TMU_CMD_DTT /* MMC SPL */ #define COPY_BL2_FNPTR_ADDR 0x02020030include/configs/intip.h +0
-8@@ -218,13 +218,6 @@#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* I2C SYSMON */ -#define CONFIG_DTT_LM63 1/* National LM63 */ -#define CONFIG_DTT_SENSORS { 0 }/* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 50, 20 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 -/* RTC configuration */ #define CONFIG_RTC_DS1337 1#define CONFIG_SYS_I2C_RTC_ADDR 0x68@@ -272,7 +265,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM include/configs/io.h +0
-6@@ -57,7 +57,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ@@ -93,11 +92,6 @@#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000/* Temp sensor/hwmon/dtt */ -#define CONFIG_DTT_LM63 1/* National LM63 */ -#define CONFIG_DTT_SENSORS { 0 }/* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 50, 20 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10/* * FLASH organization include/configs/io64.h +0
-9@@ -327,14 +327,6 @@#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* Temp sensor/hwmon/dtt */ -#define CONFIG_DTT_LM63 1/* National LM63 */ -#define CONFIG_DTT_SENSORS { 0x18, 0x4c, 0x4e }/* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 43, 13 }, { 46, 16 }, \ - { 50, 20 }, { 53, 27 }, { 56, 34 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 -/*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/ @@ -373,7 +365,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_SYS_POST_MEMORY_ON CONFIG_SYS_POST_MEMORYinclude/configs/katmai.h +0
-25@@ -123,31 +123,6 @@#define CONFIG_SYS_I2C_RTC_ADDR 0x68#define CONFIG_SYS_M41T11_BASE_YEAR 1900/* play along with linux */ -/* I2C DTT */ -#define CONFIG_DTT_ADM1021 1/* ADM1021 temp sensor support */ -#define CONFIG_SYS_DTT_BUS_NUM 1/* The I2C bus for DTT */ -/* -* standard dtt sensor configuration - bottom bit will determine local or -* remote sensor of the ADM1021, the rest determines index into -* CONFIG_SYS_DTT_ADM1021 array below. -*/ -#define CONFIG_DTT_SENSORS { 0, 1 } - -/* -* ADM1021 temp sensor configuration (see dtt/adm1021.c for details). -* there will be one entry in this array for each two (dummy) sensors in -* CONFIG_DTT_SENSORS. -* -* For Katmai board: -* - only one ADM1021 -* - i2c addr 0x18 -* - conversion rate 0x02 = 0.25 conversions/second -* - ALERT ouput disabled -* - local temp sensor enabled, min set to 0 deg, max set to 85 deg -* - remote temp sensor enabled, min set to 0 deg, max set to 85 deg -*/ -#define CONFIG_SYS_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} } -/*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ include/configs/kilauea.h +0
-4@@ -317,10 +317,6 @@#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* Standard DTT sensor configuration */ -#define CONFIG_DTT_DS1775 1 -#define CONFIG_DTT_SENSORS { 0 } -/* RTC configuration */ #define CONFIG_RTC_DS1338 1#define CONFIG_SYS_I2C_RTC_ADDR 0x68include/configs/km/km-powerpc.h +0
-1@@ -14,7 +14,6 @@#define CONFIG_BOOTCOUNT_LIMIT -#define CONFIG_CMD_DTT #define CONFIG_JFFS2_CMDLINE /* standard km ethernet_present for piggy */ include/configs/km/km83xx-common.h +0
-7@@ -215,13 +215,6 @@#define CONFIG_KM_IVM_BUS 2/* I2C2 (Mux-Port 1)*/ -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0, 1, 2, 3}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM 1 -#if defined(CONFIG_CMD_NAND )#define CONFIG_NAND_KMETER1 #define CONFIG_SYS_MAX_NAND_DEVICE 1include/configs/km82xx.h +0
-7@@ -268,13 +268,6 @@ int get_sda(void);int get_scl (void );#endif -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 /* ON Semi's LM75 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -#define CONFIG_SYS_DTT_BUS_NUM 2 -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_IMMR 0xF0000000include/configs/makalu.h +0
-5@@ -189,10 +189,6 @@#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52/* I2C boot EEPROM (24C02BN) */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1/* Bytes of address */ -/* Standard DTT sensor configuration */ -#define CONFIG_DTT_DS1775 1 -#define CONFIG_DTT_SENSORS { 0 } -/* RTC configuration */ #define CONFIG_RTC_X1205 1#define CONFIG_SYS_I2C_RTC_ADDR 0x6f@@ -231,7 +227,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI /* POST support */ include/configs/motionpro.h +0
-3@@ -33,7 +33,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IMMAP @@ -286,8 +285,6 @@/* * Temperature sensor */ -#define CONFIG_DTT_LM75 1 -#define CONFIG_DTT_SENSORS { 0x49 }/* * Environment settings include/configs/neo.h +0
-8@@ -57,7 +57,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ@@ -100,13 +99,6 @@#define CONFIG_RTC_DS1337 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 -/* Temp sensor/hwmon/dtt */ -#define CONFIG_DTT_LM63 1/* National LM63 */ -#define CONFIG_DTT_SENSORS { 0 }/* Sensor addresses */ -#define CONFIG_DTT_PWM_LOOKUPTABLE \ - { { 40, 10 }, { 50, 20 }, { 60, 40 } } -#define CONFIG_DTT_TACH_LIMIT 0xa10 -/* * FLASH organization */ include/configs/odroid_xu3.h +0
-1@@ -62,7 +62,6 @@/* FIXME: MUST BE REMOVED AFTER TMU IS TURNED ON */ #undef CONFIG_EXYNOS_TMU -#undef CONFIG_TMU_CMD_DTT#define CONFIG_DFU_ALT_SYSTEM \ "uImage fat 0 1;" \include/configs/sequoia.h +0
-9@@ -159,14 +159,6 @@#define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0#define CONFIG_4xx_CONFIG_BLOCKSIZE 16 -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1/* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 1/* use AD7414 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -/* * Default environment variables */ @@ -222,7 +214,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM include/configs/socrates.h +0
-8@@ -210,13 +210,6 @@/* I2C W83782G HW-Monitoring IC */ #define CONFIG_SYS_I2C_W83782G_ADDR 0x28/* W83782G address */ -/* I2C temp sensor */ -/* Socrates uses Maxim's DS75, which is compatible with LM75 */ -#define CONFIG_DTT_LM75 1 -#define CONFIG_DTT_SENSORS {4}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 125 -#define CONFIG_SYS_DTT_LOW_TEMP -55 -#define CONFIG_SYS_DTT_HYSTERESIS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4/* @@ -286,7 +279,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_DTT #undef CONFIG_CMD_EEPROM#define CONFIG_CMD_SDRAM #define CONFIG_CMD_REGINFO include/configs/tqma6.h +0
-10@@ -57,13 +57,6 @@#define CONFIG_I2C_MULTI_BUS #define CONFIG_SYS_I2C_SPEED 100000 -/* I2C SYSMON (LM75) */ -#define CONFIG_DTT_LM75 -#define CONFIG_DTT_MAX_TEMP 70 -#define CONFIG_DTT_MIN_TEMP -30 -#define CONFIG_DTT_HYSTERESIS 3 -#define CONFIG_CMD_DTT -/* I2C EEPROM (M24C64) */ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2@@ -373,8 +366,5 @@#endif /* Support at least the sensor on TQMa6 SOM */ -#if !defined(CONFIG_DTT_SENSORS ) -#define CONFIG_DTT_SENSORS { 0 } -#endif #endif /* __CONFIG_H */ include/configs/tqma6_mba6.h +0
-2@@ -10,8 +10,6 @@#ifndef __CONFIG_TQMA6_MBA6_H#define __CONFIG_TQMA6_MBA6_H -#define CONFIG_DTT_SENSORS { 0, 1 } -#define CONFIG_FEC_XCV_TYPE RGMII#define CONFIG_ETHPRIME "FEC"include/configs/tqma6_wru4.h +0
-4@@ -7,10 +7,6 @@#ifndef __CONFIG_TQMA6_WRU4_H#define __CONFIG_TQMA6_WRU4_H -/* DTT sensors */ -#define CONFIG_DTT_SENSORS { 0, 1 } -#define CONFIG_SYS_DTT_BUS_NUM 2 -/* Ethernet */ #define CONFIG_FEC_XCV_TYPE RMII#define CONFIG_ETHPRIME "FEC"include/configs/work_92105.h +0
-8@@ -84,14 +84,6 @@#define CONFIG_RTC_DS1374 -/* -* I2C Temperature Sensor (DTT) -*/ - -#define CONFIG_CMD_DTT -#define CONFIG_DTT_SENSORS { 0, 1 } -#define CONFIG_DTT_DS620 -/* * U-Boot General Configurations */ include/configs/xilinx-ppc.h +0
-1@@ -28,7 +28,6 @@#define CONFIG_CMD_REGINFO #undef CONFIG_CMD_JFFS2#undef CONFIG_CMD_MTDPARTS -#undef CONFIG_CMD_DTT#undef CONFIG_CMD_EEPROM/*Misc*/ include/configs/xpedite517x.h +0
-3@@ -233,8 +233,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);/* I2C DS1631 temperature sensor */ #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 -#define CONFIG_DTT_DS1621 -#define CONFIG_DTT_SENSORS { 0 }#define CONFIG_SYS_I2C_LM90_ADDR 0x4c/* I2C EEPROM - AT24C128B */ @@ -501,7 +499,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ #define CONFIG_CMD_JFFS2 include/configs/xpedite537x.h +0
-3@@ -230,8 +230,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);/* I2C DS1631 temperature sensor */ #define CONFIG_SYS_I2C_DS1621_ADDR 0x48 -#define CONFIG_DTT_DS1621 -#define CONFIG_DTT_SENSORS { 0 }#define CONFIG_SYS_I2C_LM90_ADDR 0x4c/* I2C EEPROM - AT24C128B */ @@ -353,7 +351,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NAND include/configs/xpedite550x.h +0
-3@@ -219,8 +219,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100/* I2C DS7505 temperature sensor */ -#define CONFIG_DTT_LM75 -#define CONFIG_DTT_SENSORS { 0 }#define CONFIG_SYS_I2C_LM75_ADDR 0x48/* I2C ADT7461 temperature sensor */ @@ -339,7 +337,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NAND include/configs/yosemite.h +0
-9@@ -131,14 +131,6 @@#define CONFIG_ENV_OFFSET 0x0#endif /* CONFIG_ENV_IS_IN_EEPROM */ -/* I2C SYSMON (LM75, AD7414 is almost compatible) */ -#define CONFIG_DTT_LM75 1/* ON Semi's LM75 */ -#define CONFIG_DTT_AD7414 1/* use AD7414 */ -#define CONFIG_DTT_SENSORS {0}/* Sensor addresses */ -#define CONFIG_SYS_DTT_MAX_TEMP 70 -#define CONFIG_SYS_DTT_LOW_TEMP -30 -#define CONFIG_SYS_DTT_HYSTERESIS 3 -/* * Default environment variables */ @@ -184,7 +176,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_DTT #define CONFIG_CMD_PCI #ifdef CONFIG_440EP include/dtt.h deleted +0
-47@@ -1,47 +0,0 @@ -/* -* (C) Copyright 2001 -* Erik Theisen, Wave 7 Optics, etheisen at mindspring.com. -* -* SPDX-License-Identifier: GPL-2.0+ -*/ - -/* -* Digital Thermometers and Thermostats. -*/ -#ifndef _DTT_H_ -#define _DTT_H_ - -#if defined(CONFIG_DTT_ADM1021 ) || \ - defined(CONFIG_DTT_ADT7460 ) || \ - defined(CONFIG_DTT_DS1621 ) || \ - defined(CONFIG_DTT_DS1775 ) || \ - defined(CONFIG_DTT_DS620 ) || \ - defined(CONFIG_DTT_LM63 ) || \ - defined(CONFIG_DTT_LM73 ) || \ - defined(CONFIG_DTT_LM75 ) || \ - defined(CONFIG_DTT_LM81 ) - -#define CONFIG_DTT /* We have a DTT */ - -#ifndef CONFIG_DTT_ADM1021 -#define DTT_COMMERCIAL_MAX_TEMP 70/* 0 - +70 C */ -#define DTT_INDUSTRIAL_MAX_TEMP 85/* -40 - +85 C */ -#define DTT_AUTOMOTIVE_MAX_TEMP 105/* -40 - +105 C */ - -#ifndef CONFIG_SYS_DTT_MAX_TEMP -#define CONFIG_SYS_DTT_MAX_TEMP DTT_COMMERCIAL_MAX_TEMP -#endif - -#ifndef CONFIG_SYS_DTT_HYSTERESIS -#define CONFIG_SYS_DTT_HYSTERESIS 5/* 5 C */ -#endif -#endif /* CONFIG_DTT_ADM1021 */ - -extern void dtt_init (void ); -extern int dtt_init_one (int ); -extern int dtt_read (int sensor,int reg); -extern int dtt_write (int sensor,int reg,int val); -extern int dtt_get_temp (int sensor); -#endif - -#endif /* _DTT_H_ */ include/i2c.h +0
-3@@ -571,9 +571,6 @@ void i2c_dump_msgs(struct i2c_msg *msg, int nmsgs);#if !defined(CONFIG_SYS_RTC_BUS_NUM )#define CONFIG_SYS_RTC_BUS_NUM 0#endif -#if !defined(CONFIG_SYS_DTT_BUS_NUM ) -#define CONFIG_SYS_DTT_BUS_NUM 0 -#endif #if !defined(CONFIG_SYS_SPD_BUS_NUM )#define CONFIG_SYS_SPD_BUS_NUM 0#endif scripts/config_whitelist.txt +0
-22@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_DTT CONFIG_CMD_ECCTEST CONFIG_CMD_EECONFIG CONFIG_CMD_EEPROM@@ -684,20 +683,6 @@ CONFIG_DRIVE_SATA CONFIG_DRIVE_TYPES CONFIG_DRIVE_USB CONFIG_DSP_CLUSTER_START -CONFIG_DTT -CONFIG_DTT_AD7414 -CONFIG_DTT_ADM1021 -CONFIG_DTT_DS1621 -CONFIG_DTT_DS1775 -CONFIG_DTT_DS620 -CONFIG_DTT_HYSTERESIS -CONFIG_DTT_LM63 -CONFIG_DTT_LM75 -CONFIG_DTT_MAX_TEMP -CONFIG_DTT_MIN_TEMP -CONFIG_DTT_PWM_LOOKUPTABLE -CONFIG_DTT_SENSORS -CONFIG_DTT_TACH_LIMIT CONFIG_DUOVERO CONFIG_DV_USBPHY_CTL CONFIG_DWC2_DFLT_SPEED_FULL@@ -3476,12 +3461,6 @@ CONFIG_SYS_DSPI_CTAR4 CONFIG_SYS_DSPI_CTAR5 CONFIG_SYS_DSPI_CTAR6 CONFIG_SYS_DSPI_CTAR7 -CONFIG_SYS_DTT_ADM1021 -CONFIG_SYS_DTT_BUS_NUM -CONFIG_SYS_DTT_HYSTERESIS -CONFIG_SYS_DTT_LOW_TEMP -CONFIG_SYS_DTT_MAX_TEMP -CONFIG_SYS_DTT_MIN_TEMP CONFIG_SYS_DUART_RST CONFIG_SYS_DV_CLKMODE CONFIG_SYS_DV_NOR_BOOT_CFG@@ -6142,7 +6121,6 @@ CONFIG_TIZEN CONFIG_TI_KEYSTONE_SERDES CONFIG_TI_KSNAV CONFIG_TI_SPI_MMAP -CONFIG_TMU_CMD_DTT CONFIG_TMU_TIMER CONFIG_TOTAL5200 CONFIG_TPL_DRIVERS_MISC_SUPPORT
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 10/47 Kconfig: Drop CONFIG_SYS_I2C_DS1621_ADDR
In reply to Simon GlassNow that dtt is gone, this is not used. Drop it.
Signed-off-by Simon Glass <[email protected]>
---
include/configs/xpedite517x.h | 12 ------------ include/configs/xpedite537x.h | 11 ----------- scripts/config_whitelist.txt | 1 - 3 files changed, 24 deletions(-)
include/configs/xpedite517x.h +0 -12
@@ -87,17 +87,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_MEMTEST_END 0x20000000#define CONFIG_POST (CONFIG_SYS_POST_MEMORY |\ CONFIG_SYS_POST_I2C) -#define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ - CONFIG_SYS_I2C_DS4510_ADDR, \ - CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_LM90_ADDR, \ - CONFIG_SYS_I2C_PCA9553_ADDR, \ - CONFIG_SYS_I2C_PCA953X_ADDR0, \ - CONFIG_SYS_I2C_PCA953X_ADDR1, \ - CONFIG_SYS_I2C_PCA953X_ADDR2, \ - CONFIG_SYS_I2C_PCA953X_ADDR3, \ - CONFIG_SYS_I2C_PEX8518_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR}/* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */ #define I2C_ADDR_IGNORE_LIST {0x50}
@@ -232,7 +221,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70/* I2C DS1631 temperature sensor */ -#define CONFIG_SYS_I2C_DS1621_ADDR 0x48#define CONFIG_SYS_I2C_LM90_ADDR 0x4c/* I2C EEPROM - AT24C128B */
include/configs/xpedite537x.h +0 -11
@@ -81,16 +81,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);#define CONFIG_SYS_MEMTEST_END 0x20000000#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ CONFIG_SYS_POST_I2C) -#define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ - CONFIG_SYS_I2C_DS4510_ADDR, \ - CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_LM90_ADDR, \ - CONFIG_SYS_I2C_PCA953X_ADDR0, \ - CONFIG_SYS_I2C_PCA953X_ADDR1, \ - CONFIG_SYS_I2C_PCA953X_ADDR2, \ - CONFIG_SYS_I2C_PCA953X_ADDR3, \ - CONFIG_SYS_I2C_PEX8518_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR}/* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ #define I2C_ADDR_IGNORE_LIST {0x50}
@@ -229,7 +219,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70/* I2C DS1631 temperature sensor */ -#define CONFIG_SYS_I2C_DS1621_ADDR 0x48#define CONFIG_SYS_I2C_LM90_ADDR 0x4c/* I2C EEPROM - AT24C128B */
scripts/config_whitelist.txt +0 -1
@@ -4203,7 +4203,6 @@ CONFIG_SYS_I2C_CLK_OFFSET CONFIG_SYS_I2C_DAVINCI CONFIG_SYS_I2C_DIRECT_BUS CONFIG_SYS_I2C_DPMEM_OFFSET -CONFIG_SYS_I2C_DS1621_ADDR CONFIG_SYS_I2C_DS4510_ADDR CONFIG_SYS_I2C_DSPIC_2_ADDR CONFIG_SYS_I2C_DSPIC_ADDR
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 10/47 Kconfig: Drop CONFIG_SYS_I2C_DS1621_ADDR
Hello Simon,
Am 15.05.2017 um 12:57 schrieb Simon Glass:
Quoted 9 lines
Now that dtt is gone, this is not used. Drop it.
Signed-off-by Simon Glass <[email protected]>---
include/configs/xpedite517x.h | 12 ------------ include/configs/xpedite537x.h | 11 ----------- scripts/config_whitelist.txt | 1 - 3 files changed, 24 deletions(-)
Reviewed-by Heiko Schocher <[email protected]>
bye,
Heiko
Quoted 73 lines
include/configs/xpedite517x.h +0
-12@@ -87,17 +87,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_MEMTEST_END 0x20000000#define CONFIG_POST (CONFIG_SYS_POST_MEMORY |\ CONFIG_SYS_POST_I2C) -#define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ - CONFIG_SYS_I2C_DS4510_ADDR, \ - CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_LM90_ADDR, \ - CONFIG_SYS_I2C_PCA9553_ADDR, \ - CONFIG_SYS_I2C_PCA953X_ADDR0, \ - CONFIG_SYS_I2C_PCA953X_ADDR1, \ - CONFIG_SYS_I2C_PCA953X_ADDR2, \ - CONFIG_SYS_I2C_PCA953X_ADDR3, \ - CONFIG_SYS_I2C_PEX8518_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR}/* The XPedite5170 can host an XMC which has an EEPROM at address 0x50 */ #define I2C_ADDR_IGNORE_LIST {0x50}@@ -232,7 +221,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70/* I2C DS1631 temperature sensor */ -#define CONFIG_SYS_I2C_DS1621_ADDR 0x48#define CONFIG_SYS_I2C_LM90_ADDR 0x4c/* I2C EEPROM - AT24C128B */ include/configs/xpedite537x.h +0
-11@@ -81,16 +81,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);#define CONFIG_SYS_MEMTEST_END 0x20000000#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ CONFIG_SYS_POST_I2C) -#define I2C_ADDR_LIST {CONFIG_SYS_I2C_DS1621_ADDR, \ - CONFIG_SYS_I2C_DS4510_ADDR, \ - CONFIG_SYS_I2C_EEPROM_ADDR, \ - CONFIG_SYS_I2C_LM90_ADDR, \ - CONFIG_SYS_I2C_PCA953X_ADDR0, \ - CONFIG_SYS_I2C_PCA953X_ADDR1, \ - CONFIG_SYS_I2C_PCA953X_ADDR2, \ - CONFIG_SYS_I2C_PCA953X_ADDR3, \ - CONFIG_SYS_I2C_PEX8518_ADDR, \ - CONFIG_SYS_I2C_RTC_ADDR}/* The XPedite5370 can host an XMC which has an EEPROM at address 0x50 */ #define I2C_ADDR_IGNORE_LIST {0x50}@@ -229,7 +219,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70/* I2C DS1631 temperature sensor */ -#define CONFIG_SYS_I2C_DS1621_ADDR 0x48#define CONFIG_SYS_I2C_LM90_ADDR 0x4c/* I2C EEPROM - AT24C128B */ scripts/config_whitelist.txt +0
-1@@ -4203,7 +4203,6 @@ CONFIG_SYS_I2C_CLK_OFFSET CONFIG_SYS_I2C_DAVINCI CONFIG_SYS_I2C_DIRECT_BUS CONFIG_SYS_I2C_DPMEM_OFFSET -CONFIG_SYS_I2C_DS1621_ADDR CONFIG_SYS_I2C_DS4510_ADDR CONFIG_SYS_I2C_DSPIC_2_ADDR CONFIG_SYS_I2C_DSPIC_ADDR
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 11/47 Kconfig: Drop CONFIG_SYS_I2C_DS4510_ADDR
In reply to Simon GlassThis is only used by one board and always set to 0x51. Drop this option.
Signed-off-by Simon Glass <[email protected]>
---
drivers/misc/ds4510.c | 7 +------ include/configs/xpedite517x.h | 3 --- include/configs/xpedite537x.h | 3 --- scripts/config_whitelist.txt | 1 - 4 files changed, 1 insertion(+), 13 deletions(-)
drivers/misc/ds4510.c +1 -6
@@ -14,11 +14,6 @@#include <command.h> #include "ds4510.h" -/* Default to an address that hopefully won't corrupt other i2c devices */ -#ifndef CONFIG_SYS_I2C_DS4510_ADDR -#define CONFIG_SYS_I2C_DS4510_ADDR (~0) -#endif -enum {DS4510_CMD_INFO ,DS4510_CMD_DEVICE ,
@@ -254,7 +249,7 @@ cmd_tbl_t cmd_ds4510[] = {int do_ds4510 (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) { -static uint8_t chip =CONFIG_SYS_I2C_DS4510_ADDR ; +static uint8_t chip =0x51 ;cmd_tbl_t *c;ulong ul_arg2 =0 ;ulong ul_arg3 =0 ;
include/configs/xpedite517x.h +0 -3
@@ -234,9 +234,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_I2C_RTC_ADDR 0x68#define CONFIG_SYS_M41T11_BASE_YEAR 2000 -/* GPIO/EEPROM/SRAM */ -#define CONFIG_SYS_I2C_DS4510_ADDR 0x51 -/* GPIO */ #define CONFIG_PCA953X #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
include/configs/xpedite537x.h +0 -3
@@ -232,9 +232,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);#define CONFIG_SYS_I2C_RTC_ADDR 0x68#define CONFIG_SYS_M41T11_BASE_YEAR 2000 -/* GPIO/EEPROM/SRAM */ -#define CONFIG_SYS_I2C_DS4510_ADDR 0x51 -/* GPIO */ #define CONFIG_PCA953X #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
scripts/config_whitelist.txt +0 -1
@@ -4203,7 +4203,6 @@ CONFIG_SYS_I2C_CLK_OFFSET CONFIG_SYS_I2C_DAVINCI CONFIG_SYS_I2C_DIRECT_BUS CONFIG_SYS_I2C_DPMEM_OFFSET -CONFIG_SYS_I2C_DS4510_ADDR CONFIG_SYS_I2C_DSPIC_2_ADDR CONFIG_SYS_I2C_DSPIC_ADDR CONFIG_SYS_I2C_DSPIC_IO_ADDR
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 11/47 Kconfig: Drop CONFIG_SYS_I2C_DS4510_ADDR
Quoted 3 lines · Simon Glass
This is only used by one board and always set to
0x51. Drop this option.Signed-off-by Simon Glass <[email protected]>
Reviewed-by Tom Rini <[email protected]>
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/7be79928/attachment.sig>
PATCH 11/47 Kconfig: Drop CONFIG_SYS_I2C_DS4510_ADDR
In reply to Simon GlassHello Simon,
Am 15.05.2017 um 12:57 schrieb Simon Glass:
Quoted 10 lines
This is only used by one board and always set to
0x51. Drop this option.Signed-off-by Simon Glass <[email protected]>---
drivers/misc/ds4510.c | 7 +------ include/configs/xpedite517x.h | 3 --- include/configs/xpedite537x.h | 3 --- scripts/config_whitelist.txt | 1 - 4 files changed, 1 insertion(+), 13 deletions(-)
Reviewed-by Heiko Schocher <[email protected]>
bye,
Heiko
Quoted 67 lines
drivers/misc/ds4510.c +1
-6@@ -14,11 +14,6 @@#include <command.h> #include "ds4510.h" -/* Default to an address that hopefully won't corrupt other i2c devices */ -#ifndef CONFIG_SYS_I2C_DS4510_ADDR -#define CONFIG_SYS_I2C_DS4510_ADDR (~0) -#endif -enum {DS4510_CMD_INFO ,DS4510_CMD_DEVICE ,@@ -254,7 +249,7 @@ cmd_tbl_t cmd_ds4510[] = {int do_ds4510 (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) { -static uint8_t chip =CONFIG_SYS_I2C_DS4510_ADDR ; +static uint8_t chip =0x51 ;cmd_tbl_t *c;ulong ul_arg2 =0 ;ulong ul_arg3 =0 ;include/configs/xpedite517x.h +0
-3@@ -234,9 +234,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_I2C_RTC_ADDR 0x68#define CONFIG_SYS_M41T11_BASE_YEAR 2000 -/* GPIO/EEPROM/SRAM */ -#define CONFIG_SYS_I2C_DS4510_ADDR 0x51 -/* GPIO */ #define CONFIG_PCA953X #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18include/configs/xpedite537x.h +0
-3@@ -232,9 +232,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);#define CONFIG_SYS_I2C_RTC_ADDR 0x68#define CONFIG_SYS_M41T11_BASE_YEAR 2000 -/* GPIO/EEPROM/SRAM */ -#define CONFIG_SYS_I2C_DS4510_ADDR 0x51 -/* GPIO */ #define CONFIG_PCA953X #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18scripts/config_whitelist.txt +0
-1@@ -4203,7 +4203,6 @@ CONFIG_SYS_I2C_CLK_OFFSET CONFIG_SYS_I2C_DAVINCI CONFIG_SYS_I2C_DIRECT_BUS CONFIG_SYS_I2C_DPMEM_OFFSET -CONFIG_SYS_I2C_DS4510_ADDR CONFIG_SYS_I2C_DSPIC_2_ADDR CONFIG_SYS_I2C_DSPIC_ADDR CONFIG_SYS_I2C_DSPIC_IO_ADDR
Signature · 2 lines
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
PATCH 12/47 Convert CONFIG_CMD_ECCTEST to Kconfig
In reply to Simon GlassThis converts the following to Kconfig:
CONFIG_CMD_ECCTEST
Signed-off-by Simon Glass <[email protected]>
---
arch/powerpc/cpu/ppc4xx/Kconfig | 6 ++++++ configs/katmai_defconfig | 1 + configs/t3corp_defconfig | 1 + include/configs/katmai.h | 1 - include/configs/t3corp.h | 1 - scripts/config_whitelist.txt | 1 - 6 files changed, 8 insertions(+), 3 deletions(-)
arch/powerpc/cpu/ppc4xx/Kconfig +6 -0
@@ -137,6 +137,12 @@ config CMD_CHIP_CONFIG and control the CPU and peripehrals clocks. The programmed configuration is then used when the board boots. +config CMD_ECCTEST + bool "Enable the 'ecctest' command" + help + This command tests memory ECC by single and double error bit + injection. + source "board/amcc/acadia/Kconfig" source "board/amcc/bamboo/Kconfig" source "board/amcc/bubinga/Kconfig"
configs/katmai_defconfig +1 -0
@@ -2,6 +2,7 @@ CONFIG_PPC=y CONFIG_4xx=y CONFIG_TARGET_KATMAI=y CONFIG_CMD_CHIP_CONFIG=y +CONFIG_CMD_ECCTEST=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_INFO_QUIET=y
configs/t3corp_defconfig +1 -0
@@ -2,6 +2,7 @@ CONFIG_PPC=y CONFIG_4xx=y CONFIG_TARGET_T3CORP=y CONFIG_CMD_CHIP_CONFIG=y +CONFIG_CMD_ECCTEST=y CONFIG_FIT=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5
include/configs/katmai.h +0 -1
@@ -145,7 +145,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_ECCTEST #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM
include/configs/t3corp.h +0 -1
@@ -349,7 +349,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_CMD_ECCTEST #define CONFIG_CMD_PCI #define CONFIG_CMD_SDRAM
scripts/config_whitelist.txt +0 -1
@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_ECCTEST CONFIG_CMD_EECONFIG CONFIG_CMD_EEPROM CONFIG_CMD_EEPROM_LAYOUT
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 13/47 Convert CONFIG_CMD_EECONFIG to Kconfig
In reply to Simon GlassThis converts the following to Kconfig:
CONFIG_CMD_EECONFIG
Signed-off-by Simon Glass <[email protected]>
---
board/gateworks/gw_ventana/Kconfig | 5 +++++ configs/gwventana_emmc_defconfig | 1 + configs/gwventana_gw5904_defconfig | 1 + configs/gwventana_nand_defconfig | 1 + include/configs/gw_ventana.h | 1 - include/configs/pcm058.h | 1 - scripts/config_whitelist.txt | 1 - 7 files changed, 8 insertions(+), 3 deletions(-)
board/gateworks/gw_ventana/Kconfig +5 -0
@@ -9,4 +9,9 @@ config SYS_VENDOR config SYS_CONFIG_NAME default "gw_ventana" +config CMD_EECONFIG + bool "Enable the 'econfig' command" + help + Provides access to EEPROM configuration on Gateworks Ventana + endif
configs/gwventana_emmc_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_TARGET_GW_VENTANA=y +CONFIG_CMD_EECONFIG=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y
configs/gwventana_gw5904_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_TARGET_GW_VENTANA=y +CONFIG_CMD_EECONFIG=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_WATCHDOG_SUPPORT=y
configs/gwventana_nand_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_SPL_GPIO_SUPPORT=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y CONFIG_TARGET_GW_VENTANA=y +CONFIG_CMD_EECONFIG=y CONFIG_SPL_MMC_SUPPORT=y CONFIG_SPL_SERIAL_SUPPORT=y CONFIG_SPL_NAND_SUPPORT=y
include/configs/gw_ventana.h +0 -1
@@ -143,7 +143,6 @@/* Various command support */ #define CONFIG_CMD_HDMIDETECT /* detect HDMI output device */ #define CONFIG_CMD_GSC -#define CONFIG_CMD_EECONFIG /* Gateworks EEPROM config cmd */ #define CONFIG_CMD_UNZIP /* gzwrite */ #define CONFIG_RBTREE
include/configs/pcm058.h +0 -1
@@ -88,7 +88,6 @@/* Various command support */ #define CONFIG_CMD_HDMIDETECT /* detect HDMI output device */ #define CONFIG_CMD_GSC -#define CONFIG_CMD_EECONFIG /* Gateworks EEPROM config cmd */ #define CONFIG_RBTREE /* Physical Memory Map */
scripts/config_whitelist.txt +0 -1
@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_EECONFIG CONFIG_CMD_EEPROM CONFIG_CMD_EEPROM_LAYOUT CONFIG_CMD_ENTERRCM
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 14/47 Convert CONFIG_CMD_EEPROM et al to Kconfig
In reply to Simon GlassThis converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING
Signed-off-by Simon Glass <[email protected]>
---
README | 2 - arch/arm/Kconfig | 1 + arch/arm/mach-omap2/Kconfig | 1 + arch/arm/mach-omap2/am33xx/Kconfig | 1 + arch/powerpc/cpu/mpc85xx/Kconfig | 24 +++++++++++ cmd/Kconfig | 48 ++++++++++++++++++++++ cmd/eeprom.c | 4 -- configs/C29XPCIE_NAND_defconfig | 1 + configs/C29XPCIE_NOR_SECBOOT_defconfig | 1 + configs/C29XPCIE_SPIFLASH_SECBOOT_defconfig | 1 + configs/C29XPCIE_SPIFLASH_defconfig | 1 + configs/C29XPCIE_defconfig | 1 + configs/CPCI2DP_defconfig | 1 + configs/CPCI4052_defconfig | 1 + configs/MIP405T_defconfig | 1 + configs/MIP405_defconfig | 1 + configs/MPC8323ERDB_defconfig | 1 + configs/MiniFAP_defconfig | 1 + configs/O2D300_defconfig | 1 + configs/O2DNT2_RAMBOOT_defconfig | 1 + configs/O2DNT2_defconfig | 1 + configs/O2D_defconfig | 1 + configs/O2I_defconfig | 1 + configs/O2MNT_O2M110_defconfig | 1 + configs/O2MNT_O2M112_defconfig | 1 + configs/O2MNT_O2M113_defconfig | 1 + configs/O2MNT_defconfig | 1 + configs/O3DNT_defconfig | 1 + configs/PATI_defconfig | 1 + configs/PIP405_defconfig | 1 + configs/PLU405_defconfig | 1 + configs/PMC405DE_defconfig | 1 + configs/PMC440_defconfig | 1 + configs/TQM5200S_HIGHBOOT_defconfig | 1 + configs/TQM5200S_defconfig | 1 + configs/TQM5200_B_HIGHBOOT_defconfig | 1 + configs/TQM5200_B_defconfig | 1 + configs/TQM5200_STK100_defconfig | 1 + configs/TQM5200_defconfig | 1 + configs/TQM834x_defconfig | 1 + configs/TQM855M_defconfig | 1 + configs/TQM866M_defconfig | 1 + configs/TQM885D_defconfig | 1 + configs/TWR-P1025_defconfig | 1 + configs/VOM405_defconfig | 1 + configs/a4m072_defconfig | 1 + configs/ac14xx_defconfig | 1 + configs/acadia_defconfig | 1 + configs/am335x_baltos_defconfig | 1 + configs/am335x_sl50_defconfig | 1 + configs/apf27_defconfig | 1 + configs/arches_defconfig | 1 + configs/aria_defconfig | 1 + configs/bamboo_defconfig | 1 + configs/birdland_bav335a_defconfig | 1 + configs/birdland_bav335b_defconfig | 1 + configs/bk4r1_defconfig | 1 + configs/bubinga_defconfig | 1 + configs/cam5200_defconfig | 1 + configs/cam5200_niosflash_defconfig | 1 + configs/canyonlands_defconfig | 1 + configs/charon_defconfig | 1 + configs/cl-som-am57x_defconfig | 2 + configs/cm_fx6_defconfig | 2 + configs/cm_t335_defconfig | 2 + configs/cm_t3517_defconfig | 2 + configs/cm_t35_defconfig | 2 + configs/cm_t43_defconfig | 2 + configs/cm_t54_defconfig | 2 + .../controlcenterd_36BIT_SDCARD_DEVELOP_defconfig | 1 + configs/controlcenterd_36BIT_SDCARD_defconfig | 1 + .../controlcenterd_TRAILBLAZER_DEVELOP_defconfig | 1 + configs/controlcenterd_TRAILBLAZER_defconfig | 1 + configs/d2net_v2_defconfig | 1 + configs/devconcenter_defconfig | 1 + configs/digsy_mtc_RAMBOOT_defconfig | 1 + configs/digsy_mtc_defconfig | 1 + configs/digsy_mtc_rev5_RAMBOOT_defconfig | 1 + configs/digsy_mtc_rev5_defconfig | 1 + configs/eco5pk_defconfig | 1 + configs/fo300_defconfig | 1 + configs/glacier_defconfig | 1 + configs/glacier_ramboot_defconfig | 1 + configs/haleakala_defconfig | 1 + configs/icon_defconfig | 1 + configs/imx31_phycore_defconfig | 1 + configs/imx31_phycore_eet_defconfig | 1 + configs/inetspace_v2_defconfig | 1 + configs/intip_defconfig | 1 + configs/io64_defconfig | 1 + configs/katmai_defconfig | 1 + configs/kilauea_defconfig | 1 + configs/km_kirkwood_128m16_defconfig | 1 + configs/km_kirkwood_defconfig | 1 + configs/km_kirkwood_pci_defconfig | 1 + configs/kmcoge4_defconfig | 1 + configs/kmcoge5ne_defconfig | 1 + configs/kmcoge5un_defconfig | 1 + configs/kmeter1_defconfig | 1 + configs/kmlion1_defconfig | 1 + configs/kmnusa_defconfig | 1 + configs/kmopti2_defconfig | 1 + configs/kmsugp1_defconfig | 1 + configs/kmsupx5_defconfig | 1 + configs/kmsuv31_defconfig | 1 + configs/kmtegr1_defconfig | 1 + configs/kmtepr2_defconfig | 1 + configs/kmvect1_defconfig | 1 + configs/ls1012aqds_qspi_defconfig | 1 + configs/ls2080aqds_SECURE_BOOT_defconfig | 1 + configs/ls2080aqds_defconfig | 1 + configs/ls2080aqds_nand_defconfig | 1 + configs/ls2080aqds_qspi_defconfig | 1 + configs/ls2080ardb_SECURE_BOOT_defconfig | 1 + configs/ls2080ardb_defconfig | 1 + configs/ls2080ardb_nand_defconfig | 1 + configs/luan_defconfig | 1 + configs/lwmon5_defconfig | 1 + configs/m28evk_defconfig | 1 + configs/makalu_defconfig | 1 + configs/mecp5123_defconfig | 1 + configs/mgcoge3ne_defconfig | 1 + configs/mgcoge3un_defconfig | 1 + configs/mgcoge_defconfig | 1 + configs/motionpro_defconfig | 1 + configs/mpc5121ads_defconfig | 1 + configs/mpc5121ads_rev2_defconfig | 1 + configs/mt_ventoux_defconfig | 1 + configs/net2big_v2_defconfig | 1 + configs/netspace_lite_v2_defconfig | 1 + configs/netspace_max_v2_defconfig | 1 + configs/netspace_mini_v2_defconfig | 1 + configs/netspace_v2_defconfig | 1 + configs/novena_defconfig | 1 + configs/ot1200_defconfig | 1 + configs/pcm030_LOWBOOT_defconfig | 1 + configs/pcm030_defconfig | 1 + configs/pcm051_rev1_defconfig | 1 + configs/pcm051_rev3_defconfig | 1 + configs/pcm052_defconfig | 1 + configs/pdm360ng_defconfig | 1 + configs/pengwyn_defconfig | 1 + configs/portl2_defconfig | 1 + configs/rainier_defconfig | 1 + configs/rainier_ramboot_defconfig | 1 + configs/redwood_defconfig | 1 + configs/sequoia_defconfig | 1 + configs/sequoia_ramboot_defconfig | 1 + configs/socfpga_vining_fpga_defconfig | 1 + configs/suvd3_defconfig | 1 + configs/sycamore_defconfig | 1 + configs/t3corp_defconfig | 1 + configs/tqma6dl_mba6_mmc_defconfig | 1 + configs/tqma6dl_mba6_spi_defconfig | 1 + configs/tqma6q_mba6_mmc_defconfig | 1 + configs/tqma6q_mba6_spi_defconfig | 1 + configs/tqma6s_mba6_mmc_defconfig | 1 + configs/tqma6s_mba6_spi_defconfig | 1 + configs/tqma6s_wru4_mmc_defconfig | 1 + configs/tricorder_defconfig | 1 + configs/tricorder_flash_defconfig | 1 + configs/tuge1_defconfig | 1 + configs/tuxx1_defconfig | 1 + configs/twister_defconfig | 1 + configs/vct_platinum_defconfig | 1 + configs/vct_platinum_onenand_defconfig | 1 + configs/vct_platinumavc_defconfig | 1 + configs/vct_platinumavc_onenand_defconfig | 1 + configs/vct_premium_defconfig | 1 + configs/vct_premium_onenand_defconfig | 1 + configs/walnut_defconfig | 1 + configs/work_92105_defconfig | 1 + configs/xilinx_zynqmp_zcu102_defconfig | 1 + configs/xilinx_zynqmp_zcu102_revB_defconfig | 1 + configs/xpedite1000_defconfig | 1 + configs/xpedite517x_defconfig | 1 + configs/xpedite520x_defconfig | 1 + configs/xpedite537x_defconfig | 1 + configs/yellowstone_defconfig | 1 + configs/yosemite_defconfig | 1 + configs/yucca_defconfig | 1 + configs/zynq_zc702_defconfig | 1 + configs/zynq_zc706_defconfig | 1 + configs/zynq_zybo_defconfig | 1 + include/config_cmd_all.h | 1 - include/configs/B4860QDS.h | 1 - include/configs/BSC9131RDB.h | 1 - include/configs/BSC9132QDS.h | 1 - include/configs/C29XPCIE.h | 1 - include/configs/CPCI2DP.h | 1 - include/configs/CPCI4052.h | 1 - include/configs/MIP405.h | 1 - include/configs/MPC8323ERDB.h | 1 - include/configs/P1010RDB.h | 1 - include/configs/PATI.h | 1 - include/configs/PIP405.h | 1 - include/configs/PLU405.h | 1 - include/configs/PMC405DE.h | 1 - include/configs/PMC440.h | 1 - include/configs/T102xQDS.h | 1 - include/configs/T102xRDB.h | 1 - include/configs/T1040QDS.h | 1 - include/configs/TQM5200.h | 1 - include/configs/TQM834x.h | 1 - include/configs/TQM855M.h | 1 - include/configs/TQM866M.h | 1 - include/configs/TQM885D.h | 1 - include/configs/VOM405.h | 1 - include/configs/a4m072.h | 1 - include/configs/ac14xx.h | 1 - include/configs/am335x_evm.h | 1 - include/configs/am335x_sl50.h | 1 - include/configs/am43xx_evm.h | 1 - include/configs/amcc-common.h | 1 - include/configs/apf27.h | 1 - include/configs/aria.h | 1 - include/configs/baltos.h | 1 - include/configs/bav335x.h | 1 - include/configs/cl-som-am57x.h | 2 - include/configs/cm_fx6.h | 4 -- include/configs/cm_t335.h | 4 -- include/configs/cm_t35.h | 4 -- include/configs/cm_t3517.h | 4 -- include/configs/cm_t43.h | 4 -- include/configs/cm_t54.h | 4 -- include/configs/controlcenterd.h | 1 - include/configs/digsy_mtc.h | 1 - include/configs/dlvision-10g.h | 1 - include/configs/dlvision.h | 1 - include/configs/gdppc440etx.h | 1 - include/configs/imx31_phycore.h | 1 - include/configs/io.h | 1 - include/configs/iocon.h | 1 - include/configs/km/keymile-common.h | 1 - include/configs/lacie_kw.h | 1 - include/configs/ls1012aqds.h | 1 - include/configs/ls2080aqds.h | 1 - include/configs/ls2080ardb.h | 1 - include/configs/lwmon5.h | 1 - include/configs/m28evk.h | 1 - include/configs/mecp5123.h | 1 - include/configs/motionpro.h | 1 - include/configs/mpc5121ads.h | 1 - include/configs/neo.h | 1 - include/configs/novena.h | 1 - include/configs/o2dnt-common.h | 1 - include/configs/ot1200.h | 1 - include/configs/p1_p2_rdb_pc.h | 1 - include/configs/p1_twr.h | 1 - include/configs/pcm030.h | 1 - include/configs/pcm051.h | 1 - include/configs/pcm052.h | 1 - include/configs/pdm360ng.h | 1 - include/configs/pengwyn.h | 1 - include/configs/socfpga_vining_fpga.h | 2 - include/configs/socrates.h | 1 - include/configs/tam3517-common.h | 1 - include/configs/ti_armv7_keystone2.h | 1 - include/configs/tqma6.h | 1 - include/configs/tricorder.h | 1 - include/configs/vct.h | 3 -- include/configs/work_92105.h | 1 - include/configs/xilinx-ppc.h | 1 - include/configs/xilinx_zynqmp.h | 1 - include/configs/xilinx_zynqmp_zcu102.h | 1 - include/configs/xpedite1000.h | 1 - include/configs/xpedite517x.h | 1 - include/configs/xpedite520x.h | 1 - include/configs/xpedite537x.h | 1 - include/configs/xpedite550x.h | 1 - include/configs/zynq-common.h | 1 - include/configs/zynq_zybo.h | 1 - scripts/config_whitelist.txt | 3 -- 273 files changed, 259 insertions(+), 119 deletions(-)
README +0 -2
@@ -832,8 +832,6 @@ The following options need to be configured: CONFIG_CMD_DIAG * Diagnostics CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EDITENV edit env variable - CONFIG_CMD_EEPROM * EEPROM read/write support - CONFIG_CMD_EEPROM_LAYOUT* EEPROM layout aware commands CONFIG_CMD_ELF * bootelf, bootvx CONFIG_CMD_ENV_CALLBACK * display details about env callbacks CONFIG_CMD_ENV_FLAGS * display details about env flags
arch/arm/Kconfig +1 -0
@@ -549,6 +549,7 @@ config ARCH_KEYSTONE select SYS_THUMB_BUILD select CMD_POWEROFF imply FIT + imply CMD_EEPROM config ARCH_OMAP2PLUS bool "TI OMAP2+"
arch/arm/mach-omap2/Kconfig +1 -0
@@ -125,6 +125,7 @@ config AM43XX imply SPL_SEPARATE_BSS imply SPL_SYS_MALLOC_SIMPLE imply SYS_THUMB_BUILD + imply CMD_EEPROM help Support for AM43xx SOC from Texas Instruments. The AM43xx high performance SOC features a Cortex-A9
arch/arm/mach-omap2/am33xx/Kconfig +1 -0
@@ -34,6 +34,7 @@ config TARGET_AM335X_EVM imply SPL_DM imply SPL_DM_SEQ_ALIAS imply SPL_OF_LIBFDT + imply CMD_EEPROM help This option specifies support for the AM335x GP and HS EVM development platforms. The AM335x
arch/powerpc/cpu/mpc85xx/Kconfig +24 -0
@@ -124,6 +124,7 @@ config TARGET_P1010RDB_PA select BOARD_LATE_INIT if CHAIN_OF_TRUST select SUPPORT_SPL select SUPPORT_TPL + imply CMD_EEPROM config TARGET_P1010RDB_PB bool "Support P1010RDB_PB"
@@ -131,6 +132,7 @@ config TARGET_P1010RDB_PB select BOARD_LATE_INIT if CHAIN_OF_TRUST select SUPPORT_SPL select SUPPORT_TPL + imply CMD_EEPROM config TARGET_P1022DS bool "Support P1022DS"
@@ -141,54 +143,63 @@ config TARGET_P1022DS config TARGET_P1023RDB bool "Support P1023RDB" select ARCH_P1023 + imply CMD_EEPROM config TARGET_P1020MBG bool "Support P1020MBG-PC" select SUPPORT_SPL select SUPPORT_TPL select ARCH_P1020 + imply CMD_EEPROM config TARGET_P1020RDB_PC bool "Support P1020RDB-PC" select SUPPORT_SPL select SUPPORT_TPL select ARCH_P1020 + imply CMD_EEPROM config TARGET_P1020RDB_PD bool "Support P1020RDB-PD" select SUPPORT_SPL select SUPPORT_TPL select ARCH_P1020 + imply CMD_EEPROM config TARGET_P1020UTM bool "Support P1020UTM" select SUPPORT_SPL select SUPPORT_TPL select ARCH_P1020 + imply CMD_EEPROM config TARGET_P1021RDB bool "Support P1021RDB" select SUPPORT_SPL select SUPPORT_TPL select ARCH_P1021 + imply CMD_EEPROM config TARGET_P1024RDB bool "Support P1024RDB" select SUPPORT_SPL select SUPPORT_TPL select ARCH_P1024 + imply CMD_EEPROM config TARGET_P1025RDB bool "Support P1025RDB" select SUPPORT_SPL select SUPPORT_TPL select ARCH_P1025 + imply CMD_EEPROM config TARGET_P2020RDB bool "Support P2020RDB-PC" select SUPPORT_SPL select SUPPORT_TPL select ARCH_P2020 + imply CMD_EEPROM config TARGET_P1_TWR bool "Support p1_twr"
@@ -211,6 +222,7 @@ config TARGET_T1024QDS select BOARD_LATE_INIT if CHAIN_OF_TRUST select SUPPORT_SPL select PHYS_64BIT + imply CMD_EEPROM config TARGET_T1023RDB bool "Support T1023RDB"
@@ -218,6 +230,7 @@ config TARGET_T1023RDB select BOARD_LATE_INIT if CHAIN_OF_TRUST select SUPPORT_SPL select PHYS_64BIT + imply CMD_EEPROM config TARGET_T1024RDB bool "Support T1024RDB"
@@ -225,12 +238,14 @@ config TARGET_T1024RDB select BOARD_LATE_INIT if CHAIN_OF_TRUST select SUPPORT_SPL select PHYS_64BIT + imply CMD_EEPROM config TARGET_T1040QDS bool "Support T1040QDS" select ARCH_T1040 select BOARD_LATE_INIT if CHAIN_OF_TRUST select PHYS_64BIT + imply CMD_EEPROM config TARGET_T1040RDB bool "Support T1040RDB"
@@ -377,6 +392,7 @@ config ARCH_B4420 select SYS_FSL_SEC_COMPAT_4 select SYS_PPC64 select FSL_IFC + imply CMD_EEPROM config ARCH_B4860 bool
@@ -402,6 +418,7 @@ config ARCH_B4860 select SYS_FSL_SEC_COMPAT_4 select SYS_PPC64 select FSL_IFC + imply CMD_EEPROM config ARCH_BSC9131 bool
@@ -415,6 +432,7 @@ config ARCH_BSC9131 select SYS_FSL_SEC_BE select SYS_FSL_SEC_COMPAT_4 select FSL_IFC + imply CMD_EEPROM config ARCH_BSC9132 bool
@@ -432,6 +450,7 @@ config ARCH_BSC9132 select SYS_FSL_SEC_COMPAT_4 select SYS_PPC_E500_USE_DEBUG_TLB select FSL_IFC + imply CMD_EEPROM config ARCH_C29X bool
@@ -565,6 +584,7 @@ config ARCH_P1010 select SYS_FSL_SEC_COMPAT_4 select SYS_PPC_E500_USE_DEBUG_TLB select FSL_IFC + imply CMD_EEPROM config ARCH_P1011 bool
@@ -649,6 +669,7 @@ config ARCH_P1024 select SYS_FSL_SEC_COMPAT_2 select SYS_PPC_E500_USE_DEBUG_TLB select FSL_ELBC + imply CMD_EEPROM config ARCH_P1025 bool
@@ -678,6 +699,7 @@ config ARCH_P2020 select SYS_FSL_SEC_COMPAT_2 select SYS_PPC_E500_USE_DEBUG_TLB select FSL_ELBC + imply CMD_EEPROM config ARCH_P2041 bool
@@ -821,6 +843,7 @@ config ARCH_T1023 select SYS_FSL_SEC_BE select SYS_FSL_SEC_COMPAT_5 select FSL_IFC + imply CMD_EEPROM config ARCH_T1024 bool
@@ -838,6 +861,7 @@ config ARCH_T1024 select SYS_FSL_SEC_BE select SYS_FSL_SEC_COMPAT_5 select FSL_IFC + imply CMD_EEPROM config ARCH_T1040 bool
cmd/Kconfig +48 -0
54 lines not on this page · raw message
cmd/eeprom.c +0 -4
@@ -267,10 +267,6 @@ __weak int eeprom_parse_layout_version(char *str)static unsigned char eeprom_buf[CONFIG_SYS_EEPROM_SIZE ]; -#ifndef CONFIG_EEPROM_LAYOUT_HELP_STRING -#define CONFIG_EEPROM_LAYOUT_HELP_STRING "<not defined>" -#endif -#endif enum eeprom_action {
configs/C29XPCIE_NAND_defconfig +1 -0
@@ -20,6 +20,7 @@ CONFIG_TPL_ENV_SUPPORT=y CONFIG_TPL_I2C_SUPPORT=y CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT=y CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_SF=y CONFIG_CMD_I2C=y CONFIG_CMD_MII=y
configs/C29XPCIE_NOR_SECBOOT_defconfig +1 -0
@@ -10,6 +10,7 @@ CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=-1 CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_SF=y CONFIG_CMD_I2C=y CONFIG_CMD_MII=y
configs/C29XPCIE_SPIFLASH_SECBOOT_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_SYS_EXTRA_OPTIONS="SPIFLASH" CONFIG_BOOTDELAY=-1 CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_SF=y CONFIG_CMD_I2C=y CONFIG_CMD_MII=y
configs/C29XPCIE_SPIFLASH_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_SYS_EXTRA_OPTIONS="SPIFLASH" CONFIG_BOOTDELAY=-1 CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_SF=y CONFIG_CMD_I2C=y CONFIG_CMD_MII=y
configs/C29XPCIE_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=-1 CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_SF=y CONFIG_CMD_I2C=y CONFIG_CMD_MII=y
configs/CPCI2DP_defconfig +1 -0
@@ -5,6 +5,7 @@ CONFIG_BOOTDELAY=3 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set
configs/CPCI4052_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set
configs/MIP405T_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/MIP405_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set
configs/MPC8323ERDB_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=6 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_PING=y
configs/MiniFAP_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/O2D300_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_TARGET_O2D300=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/O2DNT2_RAMBOOT_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n" CONFIG_AUTOBOOT_STOP_STR="++++++++++" +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/O2DNT2_defconfig +1 -0
@@ -7,6 +7,7 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press password to stop\n" CONFIG_AUTOBOOT_STOP_STR="++++++++++" +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/O2D_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_TARGET_O2D=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/O2I_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_TARGET_O2I=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/O2MNT_O2M110_defconfig +1 -0
@@ -5,6 +5,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M110\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/O2MNT_O2M112_defconfig +1 -0
@@ -5,6 +5,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M112\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/O2MNT_O2M113_defconfig +1 -0
@@ -5,6 +5,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="IFM_SENSOR_TYPE=\"O2M113\"" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/O2MNT_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_TARGET_O2MNT=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/O3DNT_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_TARGET_O3DNT=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/PATI_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_SYS_PROMPT="pati=> " # CONFIG_CMD_XIMG is not set # CONFIG_CMD_EDITENV is not set # CONFIG_CMD_ENV_EXISTS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FPGA is not set # CONFIG_CMD_ECHO is not set # CONFIG_CMD_ITEST is not set
configs/PIP405_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_SYS_CONSOLE_INFO_QUIET=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set
configs/PLU405_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set
configs/PMC405DE_defconfig +1 -0
@@ -10,6 +10,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set
configs/PMC440_defconfig +1 -0
@@ -10,6 +10,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/TQM5200S_HIGHBOOT_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_SYS_EXTRA_OPTIONS="TQM5200_B,TQM5200S,SYS_TEXT_BASE=0xFFF00000" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/TQM5200S_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_SYS_EXTRA_OPTIONS="TQM5200_B,TQM5200S" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/TQM5200_B_HIGHBOOT_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/TQM5200_B_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/TQM5200_STK100_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/TQM5200_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/TQM834x_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=6 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/TQM855M_defconfig +1 -0
@@ -5,6 +5,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_SNTP=y
configs/TQM866M_defconfig +1 -0
@@ -5,6 +5,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y CONFIG_CMD_SNTP=y
configs/TQM885D_defconfig +1 -0
@@ -5,6 +5,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set
configs/TWR-P1025_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_SYS_EXTRA_OPTIONS="TWR_P1025" CONFIG_BOOTDELAY=10 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/VOM405_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_BOOTDELAY=3 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_VERSION_VARIABLE=y CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/a4m072_defconfig +1 -0
@@ -7,6 +7,7 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="asdfg" +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set
configs/ac14xx_defconfig +1 -0
@@ -5,6 +5,7 @@ CONFIG_FIT=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_PROMPT="ac14xx> " CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/acadia_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/am335x_baltos_defconfig +1 -0
@@ -29,6 +29,7 @@ CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y
configs/am335x_sl50_defconfig +1 -0
@@ -26,6 +26,7 @@ CONFIG_SPL_YMODEM_SUPPORT=y # CONFIG_AUTOBOOT is not set # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y
configs/apf27_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="BIOS> " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/arches_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/aria_defconfig +1 -0
@@ -5,6 +5,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/bamboo_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/birdland_bav335a_defconfig +1 -0
@@ -26,6 +26,7 @@ CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y
configs/birdland_bav335b_defconfig +1 -0
@@ -26,6 +26,7 @@ CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y
configs/bk4r1_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y CONFIG_CMD_MEMTEST=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/bubinga_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/cam5200_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_SYS_EXTRA_OPTIONS="CAM5200,TQM5200S,TQM5200_B" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set
configs/cam5200_niosflash_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_SYS_EXTRA_OPTIONS="CAM5200,TQM5200S,TQM5200_B,CAM5200_NIOSFLASH" CONFIG_BOOTDELAY=5 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set
configs/canyonlands_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/charon_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/cl-som-am57x_defconfig +2 -0
@@ -9,6 +9,8 @@ CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_EEPROM_LAYOUT=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y
configs/cm_fx6_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set # CONFIG_CMD_XIMG is not set CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_EEPROM_LAYOUT=y # CONFIG_CMD_LOADB is not set # CONFIG_CMD_LOADS is not set # CONFIG_CMD_FLASH is not set
configs/cm_t335_defconfig +2 -0
@@ -23,6 +23,8 @@ CONFIG_SYS_PROMPT="CM-T335 # " CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_EEPROM_LAYOUT=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_PART=y
configs/cm_t3517_defconfig +2 -0
@@ -10,6 +10,8 @@ CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="CM-T3517 # " CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y +CONFIG_CMD_EEPROM_LAYOUT=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/cm_t35_defconfig +2 -0
@@ -12,6 +12,8 @@ CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="CM-T3x # " CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y +CONFIG_CMD_EEPROM_LAYOUT=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/cm_t43_defconfig +2 -0
@@ -26,6 +26,8 @@ CONFIG_SYS_PROMPT="CM-T43 # " CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_EEPROM_LAYOUT=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y
configs/cm_t54_defconfig +2 -0
@@ -15,6 +15,8 @@ CONFIG_SYS_PROMPT="CM-T54 # " CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y +CONFIG_CMD_EEPROM_LAYOUT=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_PART=y
configs/controlcenterd_36BIT_SDCARD_DEVELOP_defconfig +1 -0
@@ -16,6 +16,7 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/controlcenterd_36BIT_SDCARD_defconfig +1 -0
@@ -16,6 +16,7 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/controlcenterd_TRAILBLAZER_DEVELOP_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_BOARD_EARLY_INIT_F=y # CONFIG_CMD_BOOTM is not set # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y # CONFIG_CMD_SETEXPR is not set
configs/controlcenterd_TRAILBLAZER_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_BOARD_EARLY_INIT_F=y # CONFIG_CMD_BOOTM is not set # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y # CONFIG_CMD_SETEXPR is not set
configs/d2net_v2_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_CONSOLE_MUX=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="d2v2> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/devconcenter_defconfig +1 -0
@@ -14,6 +14,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/digsy_mtc_RAMBOOT_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/digsy_mtc_defconfig +1 -0
@@ -10,6 +10,7 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR=" " +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/digsy_mtc_rev5_RAMBOOT_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/digsy_mtc_rev5_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Press SPACE to abort autoboot in %d seconds\n" CONFIG_AUTOBOOT_DELAY_STR="d" CONFIG_AUTOBOOT_STOP_STR=" " +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/eco5pk_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_SPL=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="ECO5-PK # " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/fo300_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/glacier_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/glacier_ramboot_defconfig +1 -0
@@ -13,6 +13,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/haleakala_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/icon_defconfig +1 -0
@@ -13,6 +13,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/imx31_phycore_defconfig +1 -0
@@ -2,6 +2,7 @@ CONFIG_ARM=y CONFIG_TARGET_IMX31_PHYCORE=y CONFIG_BOOTDELAY=3 CONFIG_SYS_PROMPT="uboot> " +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_PING=y
configs/imx31_phycore_eet_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_VIDEO=y CONFIG_BOOTDELAY=3 # CONFIG_CONSOLE_MUX is not set CONFIG_SYS_CONSOLE_IS_IN_ENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_SPI=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set
configs/inetspace_v2_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_CONSOLE_MUX=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="ns2> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/intip_defconfig +1 -0
@@ -16,6 +16,7 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/io64_defconfig +1 -0
@@ -17,6 +17,7 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/katmai_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/kilauea_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/km_kirkwood_128m16_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/km_kirkwood_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/km_kirkwood_pci_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/kmcoge4_defconfig +1 -0
@@ -15,6 +15,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/kmcoge5ne_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/kmcoge5un_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/kmeter1_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/kmlion1_defconfig +1 -0
@@ -15,6 +15,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/kmnusa_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/kmopti2_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/kmsugp1_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/kmsupx5_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/kmsuv31_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/kmtegr1_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/kmtepr2_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/kmvect1_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/ls1012aqds_qspi_defconfig +1 -0
@@ -13,6 +13,7 @@ CONFIG_BOOTDELAY=10 # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_HUSH_PARSER=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/ls2080aqds_SECURE_BOOT_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=10 CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/ls2080aqds_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=10 CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/ls2080aqds_nand_defconfig +1 -0
@@ -17,6 +17,7 @@ CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/ls2080aqds_qspi_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_SYS_EXTRA_OPTIONS="QSPI_BOOT" CONFIG_QSPI_BOOT=y CONFIG_BOOTDELAY=10 CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/ls2080ardb_SECURE_BOOT_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=10 CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/ls2080ardb_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_OF_BOARD_SETUP=y CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=10 CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/ls2080ardb_nand_defconfig +1 -0
@@ -17,6 +17,7 @@ CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_GPT=y CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/luan_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/lwmon5_defconfig +1 -0
@@ -13,6 +13,7 @@ CONFIG_VERSION_VARIABLE=y CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/m28evk_defconfig +1 -0
@@ -18,6 +18,7 @@ CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/makalu_defconfig +1 -0
@@ -10,6 +10,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/mecp5123_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/mgcoge3ne_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/mgcoge3un_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/mgcoge_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/motionpro_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Autobooting in %d seconds, press \"<Esc><Esc>\" to stop\n" CONFIG_AUTOBOOT_STOP_STR="\x1b\x1b" CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/mpc5121ads_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set
configs/mpc5121ads_rev2_defconfig +1 -0
@@ -7,6 +7,7 @@ CONFIG_BOOTDELAY=5 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set
configs/mt_ventoux_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_SPL=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="mt_ventoux => " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/net2big_v2_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_CONSOLE_MUX=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="2big2> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/netspace_lite_v2_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_CONSOLE_MUX=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="ns2> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/netspace_max_v2_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_CONSOLE_MUX=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="ns2> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/netspace_mini_v2_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_CONSOLE_MUX=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="ns2> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/netspace_v2_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_CONSOLE_MUX=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="ns2> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/novena_defconfig +1 -0
@@ -21,6 +21,7 @@ CONFIG_SPL_EXT_SUPPORT=y CONFIG_SPL_I2C_SUPPORT=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/ot1200_defconfig +1 -0
@@ -7,6 +7,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/pcm030_LOWBOOT_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_TARGET_PCM030=y CONFIG_OF_BOARD_SETUP=y CONFIG_SYS_EXTRA_OPTIONS="SYS_TEXT_BASE=0xFF000000" CONFIG_BOOTDELAY=3 +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/pcm030_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_TARGET_PCM030=y CONFIG_OF_BOARD_SETUP=y CONFIG_BOOTDELAY=3 CONFIG_SYS_PROMPT="uboot> " +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/pcm051_rev1_defconfig +1 -0
@@ -28,6 +28,7 @@ CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_PART=y
configs/pcm051_rev3_defconfig +1 -0
@@ -28,6 +28,7 @@ CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_PART=y
configs/pcm052_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y CONFIG_CMD_MEMTEST=y CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/pdm360ng_defconfig +1 -0
@@ -10,6 +10,7 @@ CONFIG_SILENT_CONSOLE=y # CONFIG_CONSOLE_MUX is not set CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/pengwyn_defconfig +1 -0
@@ -29,6 +29,7 @@ CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_PART=y
configs/portl2_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_AUTOBOOT_STOP_STR=" " # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SF=y CONFIG_CMD_I2C=y
configs/rainier_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/rainier_ramboot_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/redwood_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/sequoia_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/sequoia_ramboot_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/socfpga_vining_fpga_defconfig +1 -0
@@ -19,6 +19,7 @@ CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/suvd3_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/sycamore_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/t3corp_defconfig +1 -0
@@ -13,6 +13,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/tqma6dl_mba6_mmc_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/tqma6dl_mba6_spi_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/tqma6q_mba6_mmc_defconfig +1 -0
@@ -10,6 +10,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/tqma6q_mba6_spi_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/tqma6s_mba6_mmc_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/tqma6s_mba6_spi_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/tqma6s_wru4_mmc_defconfig +1 -0
@@ -16,6 +16,7 @@ CONFIG_AUTOBOOT_ENCRYPTION=y CONFIG_AUTOBOOT_STOP_STR_SHA256="36a9e7f1c95b82ffb99743e0c5c4ce95d83c9a430aac59f84ef3cbfab6145068" CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/tricorder_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="OMAP3 Tricorder # " # CONFIG_CMD_IMI is not set # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/tricorder_flash_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_SPL=y CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMI is not set # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/tuge1_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/tuxx1_defconfig +1 -0
@@ -11,6 +11,7 @@ CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n" CONFIG_AUTOBOOT_STOP_STR=" " CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y CONFIG_CMD_MII=y
configs/twister_defconfig +1 -0
@@ -10,6 +10,7 @@ CONFIG_SPL_OS_BOOT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="twister => " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_I2C=y
configs/vct_platinum_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_VCT_PLATINUM=y CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_SYS_PROMPT="$ " +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set
configs/vct_platinum_onenand_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_SYS_PROMPT="$ " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/vct_platinumavc_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_VCT_PLATINUMAVC=y CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_SYS_PROMPT="VCT# " +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set # CONFIG_CMD_NET is not set
configs/vct_platinumavc_onenand_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_SYS_PROMPT="$ " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set
configs/vct_premium_defconfig +1 -0
@@ -4,6 +4,7 @@ CONFIG_VCT_PREMIUM=y CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_SYS_PROMPT="$ " +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y # CONFIG_CMD_SETEXPR is not set
configs/vct_premium_onenand_defconfig +1 -0
@@ -6,6 +6,7 @@ CONFIG_BOOTDELAY=5 CONFIG_SYS_CONSOLE_INFO_QUIET=y CONFIG_SYS_PROMPT="$ " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/walnut_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/work_92105_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_SPL=y CONFIG_SPL_SYS_MALLOC_SIMPLE=y CONFIG_HUSH_PARSER=y # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_SPI=y CONFIG_CMD_I2C=y
configs/xilinx_zynqmp_zcu102_defconfig +1 -0
@@ -18,6 +18,7 @@ CONFIG_SPL_SYS_MALLOC_SIMPLE=y CONFIG_SPL_OS_BOOT=y CONFIG_SYS_PROMPT="ZynqMP> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y CONFIG_CMD_MEMTEST=y CONFIG_CMD_UNZIP=y # CONFIG_CMD_FLASH is not set
configs/xilinx_zynqmp_zcu102_revB_defconfig +1 -0
@@ -18,6 +18,7 @@ CONFIG_SPL_SYS_MALLOC_SIMPLE=y CONFIG_SPL_OS_BOOT=y CONFIG_SYS_PROMPT="ZynqMP> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y CONFIG_CMD_MEMTEST=y CONFIG_CMD_UNZIP=y # CONFIG_CMD_FLASH is not set
configs/xpedite1000_defconfig +1 -0
@@ -7,6 +7,7 @@ CONFIG_BOOTDELAY=3 CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/xpedite517x_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=3 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/xpedite520x_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=3 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/xpedite537x_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_OF_STDOUT_VIA_ALIAS=y CONFIG_BOOTDELAY=3 CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y +CONFIG_CMD_EEPROM=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set CONFIG_CMD_DHCP=y
configs/yellowstone_defconfig +1 -0
@@ -10,6 +10,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/yosemite_defconfig +1 -0
@@ -10,6 +10,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_USB=y
configs/yucca_defconfig +1 -0
@@ -9,6 +9,7 @@ CONFIG_BOARD_EARLY_INIT_F=y CONFIG_HUSH_PARSER=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_EEPROM=y CONFIG_LOOPW=y CONFIG_CMD_I2C=y CONFIG_CMD_DHCP=y
configs/zynq_zc702_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_SPL_OS_BOOT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Zynq> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/zynq_zc706_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_SPL_OS_BOOT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Zynq> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
configs/zynq_zybo_defconfig +1 -0
@@ -12,6 +12,7 @@ CONFIG_SPL_OS_BOOT=y CONFIG_HUSH_PARSER=y CONFIG_SYS_PROMPT="Zynq> " # CONFIG_CMD_IMLS is not set +CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set CONFIG_CMD_MMC=y CONFIG_CMD_SF=y
include/config_cmd_all.h +0 -1
@@ -13,7 +13,6 @@* Alphabetical list of all possible commands. */ -#define CONFIG_CMD_EEPROM /* EEPROM read/write support */ #define CONFIG_CMD_FDC /* Floppy Disk Support */ #define CONFIG_CMD_FUSE /* Device fuse support */ #define CONFIG_CMD_GETTIME /* Get time since boot */
include/configs/B4860QDS.h +0 -1
@@ -702,7 +702,6 @@ unsigned long get_board_ddr_clk(void);/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/BSC9131RDB.h +0 -1
@@ -228,7 +228,6 @@ extern unsigned long get_sdram_size(void);#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000/* I2C EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
include/configs/BSC9132QDS.h +0 -1
@@ -417,7 +417,6 @@ combinations. this should be removed later#define CONFIG_SYS_EEPROM_BUS_NUM 0/* enable read and write access to EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
include/configs/C29XPCIE.h +0 -1
@@ -371,7 +371,6 @@/* I2C EEPROM */ /* enable read and write access to EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
include/configs/CPCI2DP.h +0 -1
@@ -47,7 +47,6 @@*/ #define CONFIG_CMD_PCI #define CONFIG_CMD_IRQ -#define CONFIG_CMD_EEPROM #undef CONFIG_WATCHDOG/* watchdog disabled */
include/configs/CPCI4052.h +0 -1
@@ -63,7 +63,6 @@#define CONFIG_CMD_PCI #define CONFIG_CMD_IRQ #define CONFIG_CMD_IDE -#define CONFIG_CMD_EEPROM #define CONFIG_SUPPORT_VFAT
include/configs/MIP405.h +0 -1
@@ -46,7 +46,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IRQ #define CONFIG_CMD_JFFS2
include/configs/MPC8323ERDB.h +0 -1
@@ -320,7 +320,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #if defined(CONFIG_PCI )#define CONFIG_CMD_PCI
include/configs/P1010RDB.h +0 -1
@@ -589,7 +589,6 @@ extern unsigned long get_sdram_size(void);#define MAX_NUM_PORTS 9/* for 128Bytes EEPROM */ #endif /* enable read and write access to EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
include/configs/PATI.h +0 -1
@@ -38,7 +38,6 @@*/ #define CONFIG_CMD_REGINFO #define CONFIG_CMD_REGINFO -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ #define CONFIG_BOOTCOMMAND ""/* autoboot command */
include/configs/PIP405.h +0 -1
@@ -40,7 +40,6 @@#define CONFIG_CMD_IDE #define CONFIG_CMD_PCI #define CONFIG_CMD_IRQ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_REGINFO #define CONFIG_CMD_FDC #define CONFIG_SCSI
include/configs/PLU405.h +0 -1
@@ -58,7 +58,6 @@#define CONFIG_CMD_IRQ #define CONFIG_CMD_IDE #define CONFIG_CMD_NAND -#define CONFIG_CMD_EEPROM #define CONFIG_SUPPORT_VFAT
include/configs/PMC405DE.h +0 -1
@@ -48,7 +48,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ #define CONFIG_CMD_PCI
include/configs/PMC440.h +0 -1
@@ -238,7 +238,6 @@/* Partitions */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_REGINFO
include/configs/T102xQDS.h +0 -1
@@ -780,7 +780,6 @@ unsigned long get_board_ddr_clk(void);/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/T102xRDB.h +0 -1
@@ -790,7 +790,6 @@ unsigned long get_board_ddr_clk(void);/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/T1040QDS.h +0 -1
@@ -661,7 +661,6 @@ unsigned long get_board_ddr_clk(void);/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/TQM5200.h +0 -1
@@ -144,7 +144,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO
include/configs/TQM834x.h +0 -1
@@ -273,7 +273,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO
include/configs/TQM855M.h +0 -1
@@ -115,7 +115,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2
include/configs/TQM866M.h +0 -1
@@ -129,7 +129,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2
include/configs/TQM885D.h +0 -1
@@ -125,7 +125,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE /*
include/configs/VOM405.h +0 -1
@@ -54,7 +54,6 @@* Command line configuration. */ #define CONFIG_CMD_IRQ -#define CONFIG_CMD_EEPROM #undef CONFIG_WATCHDOG/* watchdog disabled */
include/configs/a4m072.h +0 -1
@@ -81,7 +81,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #if defined(CONFIG_PCI )
include/configs/ac14xx.h +0 -1
@@ -384,7 +384,6 @@#define CONFIG_LOADS_ECHO 1#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE#undef CONFIG_CMD_IDE#define CONFIG_CMD_JFFS2
include/configs/am335x_evm.h +0 -1
@@ -176,7 +176,6 @@#define CONFIG_SYS_NS16550_COM5 0x481a8000/* UART4 */ #define CONFIG_SYS_NS16550_COM6 0x481aa000/* UART5 */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50/* Main EEPROM */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
include/configs/am335x_sl50.h +0 -1
@@ -64,7 +64,6 @@#define CONFIG_SYS_NS16550_COM5 0x481a8000/* UART4 */ #define CONFIG_SYS_NS16550_COM6 0x481aa000/* UART5 */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50/* Main EEPROM */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
include/configs/am43xx_evm.h +0 -1
@@ -23,7 +23,6 @@#endif /* I2C Configuration */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50/* Main EEPROM */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
include/configs/amcc-common.h +0 -1
@@ -51,7 +51,6 @@*/ #if defined(CONFIG_440 )#endif -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/apf27.h +0 -1
@@ -54,7 +54,6 @@/* * U-Boot Commands */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IMX_FUSE /* imx iim fuse */ #define CONFIG_CMD_MTDPARTS /* MTD partition support */ #define CONFIG_CMD_NAND /* NAND support */
include/configs/aria.h +0 -1
@@ -392,7 +392,6 @@#define CONFIG_LOADS_ECHO 1#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE#undef CONFIG_CMD_IDE#define CONFIG_CMD_JFFS2
include/configs/baltos.h +0 -1
@@ -229,7 +229,6 @@#define CONFIG_SYS_NS16550_COM5 0x481a8000/* UART4 */ #define CONFIG_SYS_NS16550_COM6 0x481aa000/* UART5 */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50/* Main EEPROM */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
include/configs/bav335x.h +0 -1
@@ -330,7 +330,6 @@ DEFAULT_LINUX_BOOT_ENV \#define CONFIG_SYS_NS16550_COM5 0x481a8000/* UART4 */ #define CONFIG_SYS_NS16550_COM6 0x481aa000/* UART5 */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50/* Main EEPROM */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
include/configs/cl-som-am57x.h +0 -2
@@ -60,8 +60,6 @@#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_I2C_EEPROM_BUS 3 -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_EEPROM_LAYOUT #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_EEPROM_SIZE 256
include/configs/cm_fx6.h +0 -4
@@ -258,14 +258,10 @@#define CONFIG_VIDEO_BMP_LOGO /* EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5#define CONFIG_SYS_EEPROM_SIZE 256 -#define CONFIG_CMD_EEPROM_LAYOUT -#define CONFIG_EEPROM_LAYOUT_HELP_STRING "v2, v3" -#endif /* __CONFIG_CM_FX6_H */
include/configs/cm_t335.h +0 -4
@@ -153,16 +153,12 @@/* Status LED polarity is inversed, so init it in the "off" state */ /* EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5#define CONFIG_SYS_EEPROM_SIZE 256 -#define CONFIG_CMD_EEPROM_LAYOUT -#define CONFIG_EEPROM_LAYOUT_HELP_STRING "v2, v3" -#ifndef CONFIG_SPL_BUILD /* * Enable PCA9555 at I2C0-0x26.
include/configs/cm_t35.h +0 -4
@@ -317,14 +317,10 @@#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000/* EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5#define CONFIG_SYS_EEPROM_SIZE 256 -#define CONFIG_CMD_EEPROM_LAYOUT -#define CONFIG_EEPROM_LAYOUT_HELP_STRING "legacy, v1, v2, v3" -#endif /* __CONFIG_H */
include/configs/cm_t3517.h +0 -4
@@ -269,14 +269,10 @@#define CONFIG_OMAP3_SPI /* EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5#define CONFIG_SYS_EEPROM_SIZE 256 -#define CONFIG_CMD_EEPROM_LAYOUT -#define CONFIG_EEPROM_LAYOUT_HELP_STRING "v1, v2, v3" -#endif /* __CONFIG_H */
include/configs/cm_t43.h +0 -4
@@ -150,14 +150,10 @@#define CONFIG_SPL_SPI_LOAD /* EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5#define CONFIG_SYS_EEPROM_SIZE 256 -#define CONFIG_CMD_EEPROM_LAYOUT -#define CONFIG_EEPROM_LAYOUT_HELP_STRING "v2, v3" -#endif /* __CONFIG_CM_T43_H */
include/configs/cm_t54.h +0 -4
@@ -69,16 +69,12 @@/* Enabled commands */ /* EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5#define CONFIG_SYS_EEPROM_SIZE 256 -#define CONFIG_CMD_EEPROM_LAYOUT -#define CONFIG_EEPROM_LAYOUT_HELP_STRING "v2, v3" -/* USB Networking options */ #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_SMSC95XX
include/configs/controlcenterd.h +0 -1
@@ -185,7 +185,6 @@#define CONFIG_PCA9698 /* NXP PCA9698 */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR 0x52#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
include/configs/digsy_mtc.h +0 -1
@@ -85,7 +85,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IRQ #define CONFIG_CMD_PCI
include/configs/dlvision-10g.h +0 -1
@@ -57,7 +57,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ/*
include/configs/dlvision.h +0 -1
@@ -55,7 +55,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ/*
include/configs/gdppc440etx.h +0 -1
@@ -147,7 +147,6 @@* Commands additional to the ones defined in amcc-common.h */ #define CONFIG_CMD_PCI -#undef CONFIG_CMD_EEPROM/* * PCI stuff
include/configs/imx31_phycore.h +0 -1
@@ -48,7 +48,6 @@/*********************************************************** * Command definition ***********************************************************/ -#define CONFIG_CMD_EEPROM #define MTDPARTS_DEFAULT "mtdparts=physmap-flash.0:128k(uboot)ro," \
include/configs/io.h +0 -1
@@ -57,7 +57,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ/*
include/configs/iocon.h +0 -1
@@ -58,7 +58,6 @@* Commands additional to the ones defined in amcc-common.h */ #define CONFIG_CMD_FPGAD -#undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ/*
include/configs/km/keymile-common.h +0 -1
@@ -14,7 +14,6 @@* Command line configuration. */ #define CONFIG_CMD_IMMAP -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_MTDPARTS
include/configs/lacie_kw.h +0 -1
@@ -120,7 +120,6 @@*/ #ifdef CONFIG_CMD_I2C /* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4/* 16-byte page size */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1/* 8-bit device address */
include/configs/ls1012aqds.h +0 -1
@@ -61,7 +61,6 @@/* EEPROM */ #define CONFIG_ID_EEPROM -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_NXID #define CONFIG_SYS_EEPROM_BUS_NUM 0#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
include/configs/ls2080aqds.h +0 -1
@@ -332,7 +332,6 @@ unsigned long get_board_ddr_clk(void);/* EEPROM */ #define CONFIG_ID_EEPROM -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_NXID #define CONFIG_SYS_EEPROM_BUS_NUM 0#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
include/configs/ls2080ardb.h +0 -1
@@ -278,7 +278,6 @@ unsigned long get_board_sys_clk(void);/* EEPROM */ #define CONFIG_ID_EEPROM -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_NXID #define CONFIG_SYS_EEPROM_BUS_NUM 0#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
include/configs/lwmon5.h +0 -1
@@ -382,7 +382,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM
include/configs/m28evk.h +0 -1
@@ -16,7 +16,6 @@/* U-Boot Commands */ #define CONFIG_FAT_WRITE -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_NAND #define CONFIG_CMD_NAND_TRIMFFS
include/configs/mecp5123.h +0 -1
@@ -288,7 +288,6 @@#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ #define CONFIG_CMD_REGINFO -#define CONFIG_CMD_EEPROM #undef CONFIG_CMD_FUSE#undef CONFIG_CMD_IDE#define CONFIG_CMD_JFFS2
include/configs/motionpro.h +0 -1
@@ -33,7 +33,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_IMMAP #define CONFIG_CMD_JFFS2
include/configs/mpc5121ads.h +0 -1
@@ -396,7 +396,6 @@#define CONFIG_LOADS_ECHO 1/* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1/* allow baudrate change */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IDE #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_REGINFO
include/configs/neo.h +0 -1
@@ -57,7 +57,6 @@/* * Commands additional to the ones defined in amcc-common.h */ -#undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ/*
include/configs/novena.h +0 -1
@@ -17,7 +17,6 @@#include "mx6_common.h" /* U-Boot Commands */ -#define CONFIG_CMD_EEPROM #define CONFIG_FAT_WRITE #define CONFIG_CMD_PCI #define CONFIG_CMD_SATA
include/configs/o2dnt-common.h +0 -1
@@ -68,7 +68,6 @@/* * Supported commands */ -#define CONFIG_CMD_EEPROM #ifdef CONFIG_PCI #define CONFIG_CMD_PCI #endif
include/configs/ot1200.h +0 -1
@@ -93,7 +93,6 @@#define CONFIG_PHY_SMSC #ifndef CONFIG_SPL -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_BUS 1#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
include/configs/p1_p2_rdb_pc.h +0 -1
@@ -631,7 +631,6 @@#define CONFIG_SYS_I2C_PCA9557_ADDR 0x18/* enable read and write access to EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
include/configs/p1_twr.h +0 -1
@@ -230,7 +230,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);#define CONFIG_SYS_I2C_PCA9555_ADDR 0x23/* enable read and write access to EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
include/configs/pcm030.h +0 -1
@@ -49,7 +49,6 @@ Serial console configuration/* * Command line configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_PCI
include/configs/pcm051.h +0 -1
@@ -108,7 +108,6 @@#define CONFIG_SYS_NS16550_COM6 0x481aa000/* UART5 */ /* I2C Configuration */ -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50/* Main EEPROM */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
include/configs/pcm052.h +0 -1
@@ -91,7 +91,6 @@#define CONFIG_SYS_RTC_BUS_NUM 2/* EEPROM (24FC256) */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2#define CONFIG_SYS_I2C_EEPROM_BUS 2
include/configs/pdm360ng.h +0 -1
@@ -367,7 +367,6 @@#define CONFIG_LOADS_ECHO 1/* echo on for serial download */ #define CONFIG_SYS_LOADS_BAUD_CHANGE 1/* allow baudrate change */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_REGINFO #undef CONFIG_CMD_FUSE
include/configs/pengwyn.h +0 -1
@@ -107,7 +107,6 @@/* I2C Configuration */ #define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_CMD_EEPROM #define CONFIG_ENV_EEPROM_IS_ON_I2C #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
include/configs/socfpga_vining_fpga.h +0 -2
@@ -12,8 +12,6 @@#define CONFIG_FAT_WRITE #define CONFIG_HW_WATCHDOG -#define CONFIG_CMD_EEPROM -/* Memory configurations */ #define PHYS_SDRAM_1_SIZE 0x40000000/* 1GiB on VINING_FPGA */
include/configs/socrates.h +0 -1
@@ -279,7 +279,6 @@/* * Command line configuration. */ -#undef CONFIG_CMD_EEPROM#define CONFIG_CMD_SDRAM #define CONFIG_CMD_REGINFO
include/configs/tam3517-common.h +0 -1
@@ -77,7 +77,6 @@/* commands to include */ #define CONFIG_CMD_NAND /* NAND support */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C #define CONFIG_SYS_OMAP24_I2C_SPEED 400000
include/configs/ti_armv7_keystone2.h +0 -1
@@ -208,7 +208,6 @@/* U-Boot command configuration */ #define CONFIG_CMD_SAVES #define CONFIG_CMD_UBIFS -#define CONFIG_CMD_EEPROM /* U-Boot general configuration */ #define CONFIG_MISC_INIT_R
include/configs/tqma6.h +0 -1
@@ -62,7 +62,6 @@#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS 5/* 32 Bytes */ #define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS 20 -#define CONFIG_CMD_EEPROM #define CONFIG_POWER #define CONFIG_POWER_I2C
include/configs/tricorder.h +0 -1
@@ -77,7 +77,6 @@/* EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2#define CONFIG_SYS_EEPROM_BUS_NUM 1
include/configs/vct.h +0 -3
@@ -77,7 +77,6 @@/* * Commands */ -#define CONFIG_CMD_EEPROM /* * Only Premium/Platinum have ethernet support right now
@@ -255,8 +254,6 @@ int vct_gpio_get(int pin);* (NOR/OneNAND) usage and Linux kernel booting. */ #if defined(CONFIG_VCT_SMALL_IMAGE ) -#undef CONFIG_CMD_EEPROM -#undef CONFIG_CMD_EEPROM#undef CONFIG_CMD_IRQ#undef CONFIG_CMD_LOADY#undef CONFIG_CMD_REGINFO
include/configs/work_92105.h +0 -1
@@ -74,7 +74,6 @@* I2C EEPROM */ -#define CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_EEPROM_ADDR 0x56#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
include/configs/xilinx-ppc.h +0 -1
@@ -28,7 +28,6 @@#define CONFIG_CMD_REGINFO #undef CONFIG_CMD_JFFS2#undef CONFIG_CMD_MTDPARTS -#undef CONFIG_CMD_EEPROM/*Misc*/ #define CONFIG_SYS_LONGHELP /* undef to save memory */
include/configs/xilinx_zynqmp.h +0 -1
@@ -184,7 +184,6 @@/* EEPROM */ #ifdef CONFIG_ZYNQMP_EEPROM -# define CONFIG_CMD_EEPROM # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2# define CONFIG_SYS_I2C_EEPROM_ADDR 0x54# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
include/configs/xilinx_zynqmp_zcu102.h +0 -1
@@ -44,7 +44,6 @@#define CONFIG_ZYNQMP_XHCI_LIST {ZYNQMP_USB0_XHCI_BASEADDR}#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_CMD_EEPROM #define CONFIG_ZYNQ_EEPROM_BUS 5#define CONFIG_ZYNQ_GEM_EEPROM_ADDR 0x54#define CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET 0x20
include/configs/xpedite1000.h +0 -1
@@ -175,7 +175,6 @@ extern void out32(unsigned int, unsigned long);/* * Command configuration */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_PCI
include/configs/xpedite517x.h +0 -1
@@ -484,7 +484,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_IRQ #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NAND
include/configs/xpedite520x.h +0 -1
@@ -287,7 +287,6 @@/* * Command configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NAND #define CONFIG_CMD_PCA953X
include/configs/xpedite537x.h +0 -1
@@ -337,7 +337,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NAND #define CONFIG_CMD_PCA953X
include/configs/xpedite550x.h +0 -1
@@ -337,7 +337,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);/* * Command configuration. */ -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_NAND #define CONFIG_CMD_PCA953X
include/configs/zynq-common.h +0 -1
@@ -145,7 +145,6 @@/* EEPROM */ #ifdef CONFIG_ZYNQ_EEPROM -# define CONFIG_CMD_EEPROM # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1# define CONFIG_SYS_I2C_EEPROM_ADDR 0x54# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
include/configs/zynq_zybo.h +0 -1
@@ -14,7 +14,6 @@#define CONFIG_ZYNQ_I2C0 #define CONFIG_ZYNQ_I2C1 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 -#define CONFIG_CMD_EEPROM #define CONFIG_ZYNQ_GEM_EEPROM_ADDR 0x50#define CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET 0xFA#define CONFIG_DISPLAY
scripts/config_whitelist.txt +0 -3
@@ -384,8 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_EEPROM -CONFIG_CMD_EEPROM_LAYOUT CONFIG_CMD_ENTERRCM CONFIG_CMD_ENV CONFIG_CMD_ENV_CALLBACK
@@ -745,7 +743,6 @@ CONFIG_EDB93XX_SDCS2 CONFIG_EDB93XX_SDCS3 CONFIG_EEPRO100 CONFIG_EEPRO100_SROM_WRITE -CONFIG_EEPROM_LAYOUT_HELP_STRING CONFIG_EFLASH_PROTSECTORS CONFIG_EHCI_DESC_BIG_ENDIAN CONFIG_EHCI_HCD_INIT_AFTER_RESET
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 14/47 Convert CONFIG_CMD_EEPROM et al to Kconfig
Quoted 6 lines · Simon Glass
This converts the following to
Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRINGSigned-off-by Simon Glass <[email protected]>
[snip]
Quoted 1 line
273 files changed, 259 insertions(+), 119 deletions(-)
I feel there needs to be a bit more poking on places to imply CMD_EEPROM. Thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/d9d4cdba/attachment.sig>
PATCH 14/47 Convert CONFIG_CMD_EEPROM et al to Kconfig
Hi Tom,
Quoted 7 lines · Tom Rini
Quoted 5 lines · Simon Glass
This converts the following to
Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING
Quoted 6 lines
Quoted 1 line
Signed-off-by Simon Glass <[email protected]>[snip]
Quoted 1 line
273 files changed, 259 insertions(+), 119 deletions(-)I feel there needs to be a bit more poking on places to imply
CMD_EEPROM. Thanks!
I did try pretty hard on this. Part of the problem is that some boards that have a shared include file do not have a shared Kconfig option.
Regards,
Simon
PATCH 14/47 Convert CONFIG_CMD_EEPROM et al to Kconfig
Quoted 11 lines · Simon Glass
Hi Tom,
Quoted 8 lines · Tom Rini
Quoted 6 lines · Simon Glass
This converts the following to
Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRINGSigned-off-by Simon Glass <[email protected]>
Quoted 8 lines
Quoted 5 lines
[snip]
Quoted 1 line
273 files changed, 259 insertions(+), 119 deletions(-)I feel there needs to be a bit more poking on places to imply
CMD_EEPROM. Thanks!I did try pretty hard on this. Part of the problem is that some boards that have a shared include file do not have a shared
Kconfigoption.
I guess we can cycle back here later, this is OK for now, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/479de4fd/attachment.sig>
PATCH 15/47 Convert CONFIG_CMD_ENTERRCM to Kconfig
In reply to Simon GlassThis converts the following to Kconfig:
CONFIG_CMD_ENTERRCM
Signed-off-by Simon Glass <[email protected]>
---
arch/arm/mach-tegra/Kconfig | 16 ++++++++++++++++ include/configs/tegra-common.h | 2 -- scripts/config_whitelist.txt | 1 - 3 files changed, 16 insertions(+), 3 deletions(-)
arch/arm/mach-tegra/Kconfig +16 -0
@@ -126,4 +126,20 @@ source "arch/arm/mach-tegra/tegra124/Kconfig" source "arch/arm/mach-tegra/tegra210/Kconfig" source "arch/arm/mach-tegra/tegra186/Kconfig" +config CMD_ENTERRCM + bool "Enable 'enterrcm' command" + default y + help + Tegra's boot ROM supports a mode whereby code may be downloaded and + flash-programmed over a USB connection. On dev boards, this is + typically entered by holding down a "force recovery" button and + resetting the CPU. However, not all boards have such a button (one + example is the Compulab Trimslice), so a method to enter RCM from + software is useful. + + Even on boards other than Trimslice, controlling this over a UART + may be useful, e.g. to allow simple remote control without the need + for mechanical button actuators, or hooking up relays/... to the + button. + endif
include/configs/tegra-common.h +0 -2
@@ -87,8 +87,6 @@ CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) -#define CONFIG_CMD_ENTERRCM -/* Defines for SPL */ #define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_BOARD_INIT
scripts/config_whitelist.txt +0 -1
@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_ENTERRCM CONFIG_CMD_ENV CONFIG_CMD_ENV_CALLBACK CONFIG_CMD_ENV_FLAGS
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 16/47 Convert CONFIG_CMD_ENV to Kconfig
In reply to Simon GlassThis converts the following to Kconfig:
CONFIG_CMD_ENV
Signed-off-by Simon Glass <[email protected]>
---
include/configs/ap_sh4a_4a.h | 1 - include/configs/calimain.h | 1 - include/configs/clearfog.h | 1 - include/configs/colibri_pxa270.h | 1 - include/configs/controlcenterdc.h | 1 - include/configs/da850evm.h | 2 -- include/configs/db-88f6720.h | 1 - include/configs/db-88f6820-amc.h | 1 - include/configs/db-88f6820-gp.h | 1 - include/configs/db-mv784mp-gp.h | 1 - include/configs/dns325.h | 1 - include/configs/dockstar.h | 1 - include/configs/dragonboard410c.h | 1 - include/configs/ds414.h | 1 - include/configs/ea20.h | 2 -- include/configs/ecovec.h | 1 - include/configs/espt.h | 1 - include/configs/goflexhome.h | 1 - include/configs/hikey.h | 1 - include/configs/iconnect.h | 1 - include/configs/ipam390.h | 1 - include/configs/lacie_kw.h | 1 - include/configs/ls1012a_common.h | 1 - include/configs/ls1043a_common.h | 3 --- include/configs/ls1046a_common.h | 3 --- include/configs/ls2080a_common.h | 1 - include/configs/lsxl.h | 1 - include/configs/maxbcm.h | 1 - include/configs/meson-gxbb-common.h | 2 -- include/configs/mv-plug-common.h | 1 - include/configs/omapl138_lcdk.h | 2 -- include/configs/openrd.h | 1 - include/configs/pogo_e02.h | 1 - include/configs/r0p7734.h | 1 - include/configs/s32v234evb.h | 1 - include/configs/shmin.h | 1 - include/configs/spear-common.h | 1 - include/configs/theadorable.h | 1 - include/configs/vexpress_aemv8a.h | 1 - include/configs/vme8349.h | 4 ---- include/configs/x600.h | 1 - include/configs/xilinx_zynqmp.h | 1 - include/configs/zipitz2.h | 1 - scripts/config_whitelist.txt | 1 - 44 files changed, 55 deletions(-)
include/configs/ap_sh4a_4a.h +0 -1
@@ -17,7 +17,6 @@#define CONFIG_SYS_TEXT_BASE 0x8BFC0000#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_ENV #define CONFIG_BOOTARGS "console=ttySC4,115200"
include/configs/calimain.h +0 -1
@@ -299,7 +299,6 @@/* * U-Boot commands */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_SAVES #ifndef CONFIG_DRIVER_TI_EMAC
include/configs/clearfog.h +0 -1
@@ -24,7 +24,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_PCI /* I2C */
include/configs/colibri_pxa270.h +0 -1
@@ -51,7 +51,6 @@/* * Bootloader Components Configuration */ -#define CONFIG_CMD_ENV /* I2C support */ #ifdef CONFIG_SYS_I2C
include/configs/controlcenterdc.h +0 -1
@@ -33,7 +33,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_I2C #define CONFIG_CMD_PCI #define CONFIG_CMD_SCSI
include/configs/da850evm.h +0 -2
@@ -273,7 +273,6 @@/* * U-Boot commands */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_SAVES #ifdef CONFIG_CMD_BDI
@@ -302,7 +301,6 @@ !defined(CONFIG_USE_SPIFLASH)#define CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_SIZE (16 << 10) -#undef CONFIG_CMD_ENV#endif #ifndef CONFIG_DIRECT_NOR_BOOT
include/configs/db-88f6720.h +0 -1
@@ -23,7 +23,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV /* I2C */ #define CONFIG_SYS_I2C
include/configs/db-88f6820-amc.h +0 -1
@@ -24,7 +24,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_PCI /* SPI NOR flash default params, used by sf commands */
include/configs/db-88f6820-gp.h +0 -1
@@ -24,7 +24,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_PCI #define CONFIG_SCSI
include/configs/db-mv784mp-gp.h +0 -1
@@ -25,7 +25,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_NAND #define CONFIG_CMD_PCI #define CONFIG_CMD_SATA
include/configs/dns325.h +0 -1
@@ -28,7 +28,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_NAND #define CONFIG_CMD_IDE #define CONFIG_SYS_MVFS
include/configs/dockstar.h +0 -1
@@ -23,7 +23,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_NAND /* * mv-common.h should be defined after CMD configs since it used them
include/configs/dragonboard410c.h +0 -1
@@ -46,7 +46,6 @@#define CONFIG_USB_ETHER_SMSC95XX /* Extra Commands */ -#define CONFIG_CMD_ENV /* Enable that for switching of boot partitions */ /* Disabled by default as some sub-commands can brick eMMC */ /*#define CONFIG_SUPPORT_EMMC_BOOT */
include/configs/ds414.h +0 -1
@@ -23,7 +23,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV /* I2C */ #define CONFIG_SYS_I2C
include/configs/ea20.h +0 -2
@@ -128,7 +128,6 @@/* * U-Boot commands */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_SAVES #ifdef CONFIG_CMD_BDI
@@ -169,7 +168,6 @@ !defined(CONFIG_USE_SPIFLASH)#define CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_SIZE (16 << 10) -#undef CONFIG_CMD_ENV#endif /* additions for new relocation code, must added to all boards */
include/configs/ecovec.h +0 -1
@@ -29,7 +29,6 @@#define CONFIG_SYS_TEXT_BASE 0x8FFC0000#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_ENV #define CONFIG_BOOTARGS "console=ttySC0,115200"
include/configs/espt.h +0 -1
@@ -18,7 +18,6 @@* Command line configuration. */ #define CONFIG_CMD_SDRAM -#define CONFIG_CMD_ENV #define CONFIG_BOOTARGS "console=ttySC0,115200 root=1f01"#define CONFIG_ENV_OVERWRITE 1
include/configs/goflexhome.h +0 -1
@@ -43,7 +43,6 @@* Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_NAND #define CONFIG_CMD_IDE #define CONFIG_SYS_MVFS /* Picks up Filesystem from mv-common.h */
include/configs/hikey.h +0 -1
@@ -73,7 +73,6 @@#define CONFIG_FS_EXT4 /* Command line configuration */ -#define CONFIG_CMD_ENV #define CONFIG_MTD_PARTITIONS
include/configs/iconnect.h +0 -1
@@ -32,7 +32,6 @@* Commands configuration */ #define CONFIG_SYS_MVFS -#define CONFIG_CMD_ENV #define CONFIG_CMD_NAND /*
include/configs/ipam390.h +0 -1
@@ -241,7 +241,6 @@/* * U-Boot commands */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_SAVES #ifdef CONFIG_CMD_BDI
include/configs/lacie_kw.h +0 -1
@@ -43,7 +43,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_IDE #ifndef CONFIG_NETSPACE_MINI_V2 /* No USB ports on Network Space v2 Mini */ #endif
include/configs/ls1012a_common.h +0 -1
@@ -85,7 +85,6 @@#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }/* Command line configuration */ -#define CONFIG_CMD_ENV #undef CONFIG_CMD_IMLS#define CONFIG_SYS_HZ 1000
include/configs/ls1043a_common.h +0 -3
@@ -174,9 +174,6 @@#endif /* Command line configuration */ -#ifndef SPL_NO_ENV -#define CONFIG_CMD_ENV -#endif /* MMC */ #ifndef SPL_NO_MMC
include/configs/ls1046a_common.h +0 -3
@@ -139,9 +139,6 @@#define CONFIG_SYS_I2C_MXC_I2C4 /* Command line configuration */ -#ifndef SPL_NO_ENV -#define CONFIG_CMD_ENV -#endif /* MMC */ #ifndef SPL_NO_MMC
include/configs/ls2080a_common.h +0 -1
@@ -160,7 +160,6 @@ unsigned long long get_qixis_addr(void);#endif /* Command line configuration */ -#define CONFIG_CMD_ENV /* Miscellaneous configurable options */ #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
include/configs/lsxl.h +0 -1
@@ -38,7 +38,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_IDE /*
include/configs/maxbcm.h +0 -1
@@ -23,7 +23,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV /* I2C */ #define CONFIG_SYS_I2C
include/configs/meson-gxbb-common.h +0 -2
@@ -26,8 +26,6 @@#define GICD_BASE 0xc4301000#define GICC_BASE 0xc4302000 -#define CONFIG_CMD_ENV -/* Monitor Command Prompt */ /* Console I/O Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
include/configs/mv-plug-common.h +0 -1
@@ -28,7 +28,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_IDE /*
include/configs/omapl138_lcdk.h +0 -2
@@ -284,7 +284,6 @@/* * U-Boot commands */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_SAVES #ifdef CONFIG_CMD_BDI #define CONFIG_CLOCKS
@@ -309,7 +308,6 @@ !defined(CONFIG_USE_SPIFLASH)#define CONFIG_ENV_IS_NOWHERE #define CONFIG_ENV_SIZE (16 << 10) -#undef CONFIG_CMD_ENV#endif /* SD/MMC */
include/configs/openrd.h +0 -1
@@ -26,7 +26,6 @@* Commands configuration */ #define CONFIG_SYS_MVFS -#define CONFIG_CMD_ENV #define CONFIG_CMD_NAND #define CONFIG_CMD_IDE
include/configs/pogo_e02.h +0 -1
@@ -29,7 +29,6 @@* Commands configuration */ #define CONFIG_SYS_MVFS -#define CONFIG_CMD_ENV #define CONFIG_CMD_NAND /*
include/configs/r0p7734.h +0 -1
@@ -17,7 +17,6 @@#define CONFIG_SYS_TEXT_BASE 0x8FFC0000#define CONFIG_CMD_SDRAM -#define CONFIG_CMD_ENV #define CONFIG_BOOTARGS "console=ttySC3,115200"
include/configs/s32v234evb.h +0 -1
@@ -127,7 +127,6 @@#define CONFIG_LOADADDR 0xC307FFC0#define CONFIG_BOOTARGS "console=ttyLF0 root=/dev/ram rw" -#define CONFIG_CMD_ENV #define CONFIG_EXTRA_ENV_SETTINGS \ "boot_scripts=boot.scr.uimg boot.scr\0" \ "scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
include/configs/shmin.h +0 -1
@@ -16,7 +16,6 @@/* #define CONFIG_T_SH7706LSR 1 */ #define CONFIG_CMD_SDRAM -#define CONFIG_CMD_ENV #define CONFIG_BOOTARGS "console=ttySC0,115200"
include/configs/spear-common.h +0 -1
@@ -97,7 +97,6 @@* Command support defines */ #define CONFIG_CMD_NAND -#define CONFIG_CMD_ENV #define CONFIG_CMD_SAVES /*
include/configs/theadorable.h +0 -1
@@ -23,7 +23,6 @@/* * Commands configuration */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_SATA /*
include/configs/vexpress_aemv8a.h +0 -1
@@ -125,7 +125,6 @@#endif /*#define CONFIG_MENU_SHOW*/ -#define CONFIG_CMD_ENV /* BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE
include/configs/vme8349.h +0 -4
@@ -351,10 +351,6 @@#define CONFIG_CMD_PCI #endif -#if defined(CONFIG_SYS_RAMBOOT ) -#undef CONFIG_CMD_ENV -#endif -/* Pass Ethernet MAC to VxWorks */ #define CONFIG_SYS_VXWORKS_MAC_PTR 0x000043f0
include/configs/x600.h +0 -1
@@ -107,7 +107,6 @@/* * Command support defines */ -#define CONFIG_CMD_ENV #define CONFIG_CMD_FPGA_LOADMK #define CONFIG_CMD_MTDPARTS #define CONFIG_CMD_NAND
include/configs/xilinx_zynqmp.h +0 -1
@@ -52,7 +52,6 @@ { 4800, 9600, 19200, 38400, 57600, 115200 }/* Command line configuration */ -#define CONFIG_CMD_ENV #define CONFIG_MP /* BOOTP options */
include/configs/zipitz2.h +0 -1
@@ -54,7 +54,6 @@/* * Bootloader Components Configuration */ -#define CONFIG_CMD_ENV /* * MMC Card Configuration
scripts/config_whitelist.txt +0 -1
@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_ENV CONFIG_CMD_ENV_CALLBACK CONFIG_CMD_ENV_FLAGS CONFIG_CMD_ERRATA
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 16/47 Convert CONFIG_CMD_ENV to Kconfig
Quoted 4 lines · Simon Glass
This converts the following to
Kconfig:
CONFIG_CMD_ENVSigned-off-by Simon Glass <[email protected]>
We need to re-word this because CONFIG_CMD_ENV isn't actually used anywhere.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/2a21920c/attachment.sig>
PATCH 17/47 Convert CONFIG_CMD_ENV_CALLBACK to Kconfig
In reply to Simon GlassThis converts the following to Kconfig:
CONFIG_CMD_ENV_CALLBACK
Signed-off-by Simon Glass <[email protected]>
---
README | 1 - cmd/Kconfig | 8 ++++++++ configs/sandbox_defconfig | 1 + configs/sandbox_noblk_defconfig | 1 + configs/sandbox_spl_defconfig | 1 + include/configs/sandbox.h | 1 - scripts/config_whitelist.txt | 1 - 7 files changed, 11 insertions(+), 3 deletions(-)
README +0 -1
@@ -833,7 +833,6 @@ The following options need to be configured: CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EDITENV edit env variable CONFIG_CMD_ELF * bootelf, bootvx - CONFIG_CMD_ENV_CALLBACK * display details about env callbacks CONFIG_CMD_ENV_FLAGS * display details about env flags CONFIG_CMD_ENV_EXISTS * check existence of env variable CONFIG_CMD_EXPORTENV * export the environment
cmd/Kconfig +8 -0
@@ -314,6 +314,14 @@ config CMD_ENV_EXISTS Check if a variable is defined in the environment for use in shell scripting. +config CMD_ENV_CALLBACK + bool "env callbacks - print callbacks and their associated variables" + help + Some environment variable have callbacks defined by + U_BOOT_ENV_CALLBACK. These are called when the variable changes. + For example changing "baudrate" adjust the serial baud rate. This + command lists the currently defined callbacks. + endmenu menu "Memory commands"
configs/sandbox_defconfig +1 -0
@@ -22,6 +22,7 @@ CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_ENV_CALLBACK=y CONFIG_CMD_MD5SUM=y CONFIG_LOOPW=y CONFIG_CMD_MEMTEST=y
configs/sandbox_noblk_defconfig +1 -0
@@ -22,6 +22,7 @@ CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_ENV_CALLBACK=y CONFIG_CMD_MD5SUM=y CONFIG_LOOPW=y CONFIG_CMD_MEMTEST=y
configs/sandbox_spl_defconfig +1 -0
@@ -29,6 +29,7 @@ CONFIG_CMD_BOOTZ=y # CONFIG_CMD_IMLS is not set CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y +CONFIG_CMD_ENV_CALLBACK=y CONFIG_CMD_MD5SUM=y CONFIG_LOOPW=y CONFIG_CMD_MEMTEST=y
include/configs/sandbox.h +0 -1
@@ -110,7 +110,6 @@#define CONFIG_CMD_SANDBOX #define CONFIG_CMD_ENV_FLAGS -#define CONFIG_CMD_ENV_CALLBACK #define CONFIG_BOOTARGS ""
scripts/config_whitelist.txt +0 -1
@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_ENV_CALLBACK CONFIG_CMD_ENV_FLAGS CONFIG_CMD_ERRATA CONFIG_CMD_ESBC_VALIDATE
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 18/47 Convert CONFIG_CMD_ENV_FLAGS to Kconfig
In reply to Simon GlassThis converts the following to Kconfig:
CONFIG_CMD_ENV_FLAGS
Signed-off-by Simon Glass <[email protected]>
---
README | 1 - cmd/Kconfig | 8 ++++++++ configs/ids8313_defconfig | 1 + configs/sandbox_defconfig | 1 + configs/sandbox_noblk_defconfig | 1 + configs/sandbox_spl_defconfig | 1 + include/configs/ids8313.h | 1 - include/configs/sandbox.h | 2 -- scripts/config_whitelist.txt | 1 - 9 files changed, 12 insertions(+), 5 deletions(-)
README +0 -1
@@ -833,7 +833,6 @@ The following options need to be configured: CONFIG_CMD_ECHO echo arguments CONFIG_CMD_EDITENV edit env variable CONFIG_CMD_ELF * bootelf, bootvx - CONFIG_CMD_ENV_FLAGS * display details about env flags CONFIG_CMD_ENV_EXISTS * check existence of env variable CONFIG_CMD_EXPORTENV * export the environment CONFIG_CMD_EXT2 * ext2 command support
cmd/Kconfig +8 -0
@@ -322,6 +322,14 @@ config CMD_ENV_CALLBACK For example changing "baudrate" adjust the serial baud rate. This command lists the currently defined callbacks. +config CMD_ENV_FLAGS + bool "env flags -print variables that have non-default flags" + help + Some environment variables have special flags that control their + behaviour. For example, serial# can only be written once and cannot + be deleted. This command shows the variables that have special + flags. + endmenu menu "Memory commands"
configs/ids8313_defconfig +1 -0
@@ -13,6 +13,7 @@ CONFIG_HUSH_PARSER=y CONFIG_AUTOBOOT_KEYED=y CONFIG_AUTOBOOT_PROMPT="Enter password - autoboot in %d seconds...\n" CONFIG_AUTOBOOT_DELAY_STR="ids" +CONFIG_CMD_ENV_FLAGS=y CONFIG_CMD_SPI=y CONFIG_CMD_I2C=y # CONFIG_CMD_SETEXPR is not set
configs/sandbox_defconfig +1 -0
@@ -23,6 +23,7 @@ CONFIG_CMD_BOOTZ=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y CONFIG_CMD_ENV_CALLBACK=y +CONFIG_CMD_ENV_FLAGS=y CONFIG_CMD_MD5SUM=y CONFIG_LOOPW=y CONFIG_CMD_MEMTEST=y
configs/sandbox_noblk_defconfig +1 -0
@@ -23,6 +23,7 @@ CONFIG_CMD_BOOTZ=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y CONFIG_CMD_ENV_CALLBACK=y +CONFIG_CMD_ENV_FLAGS=y CONFIG_CMD_MD5SUM=y CONFIG_LOOPW=y CONFIG_CMD_MEMTEST=y
configs/sandbox_spl_defconfig +1 -0
@@ -30,6 +30,7 @@ CONFIG_CMD_BOOTZ=y CONFIG_CMD_ASKENV=y CONFIG_CMD_GREPENV=y CONFIG_CMD_ENV_CALLBACK=y +CONFIG_CMD_ENV_FLAGS=y CONFIG_CMD_MD5SUM=y CONFIG_LOOPW=y CONFIG_CMD_MEMTEST=y
include/configs/ids8313.h +0 -1
@@ -445,7 +445,6 @@#define CONFIG_UBOOTPATH "ids8313/u-boot.bin"#define CONFIG_FDTFILE "ids8313/ids8313.dtb"#define CONFIG_LOADADDR 0x400000 -#define CONFIG_CMD_ENV_FLAGS #define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"/* Initial Memory map for Linux*/
include/configs/sandbox.h +0 -2
@@ -109,8 +109,6 @@#define CONFIG_CMD_SANDBOX -#define CONFIG_CMD_ENV_FLAGS -#define CONFIG_BOOTARGS ""#ifndef SANDBOX_NO_SDL
scripts/config_whitelist.txt +0 -1
@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_ENV_FLAGS CONFIG_CMD_ERRATA CONFIG_CMD_ESBC_VALIDATE CONFIG_CMD_ETHSW
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 19/47 Convert CONFIG_CMD_ERRATA to Kconfig
In reply to Simon GlassThis converts the following to Kconfig:
CONFIG_CMD_ERRATA
Signed-off-by Simon Glass <[email protected]>
---
arch/powerpc/cpu/mpc85xx/Kconfig | 8 ++++++++ configs/controlcenterd_TRAILBLAZER_DEVELOP_defconfig | 1 + configs/controlcenterd_TRAILBLAZER_defconfig | 1 + include/configs/B4860QDS.h | 1 - include/configs/BSC9131RDB.h | 1 - include/configs/BSC9132QDS.h | 1 - include/configs/C29XPCIE.h | 1 - include/configs/MPC8572DS.h | 1 - include/configs/P1010RDB.h | 1 - include/configs/P1022DS.h | 1 - include/configs/P2041RDB.h | 1 - include/configs/T102xQDS.h | 1 - include/configs/T102xRDB.h | 1 - include/configs/T1040QDS.h | 1 - include/configs/T104xRDB.h | 1 - include/configs/T208xQDS.h | 1 - include/configs/T208xRDB.h | 1 - include/configs/T4240RDB.h | 1 - include/configs/UCP1020.h | 1 - include/configs/controlcenterd.h | 1 - include/configs/corenet_ds.h | 1 - include/configs/cyrus.h | 1 - include/configs/km/kmp204x-common.h | 1 - include/configs/t4qds.h | 1 - scripts/config_whitelist.txt | 1 - 25 files changed, 10 insertions(+), 22 deletions(-)
arch/powerpc/cpu/mpc85xx/Kconfig +8 -0
@@ -4,6 +4,14 @@ menu "mpc85xx CPU" config SYS_CPU default "mpc85xx" +config CMD_ERRATA + bool "Enable the 'errata' command" + depends on MPC85xx + default y if MPC85xx + help + This enables the 'errata' command which displays a list of errata + work-arounds which are enabled for the current board. + choice prompt "Target select" optional
configs/controlcenterd_TRAILBLAZER_DEVELOP_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_BOARD_EARLY_INIT_F=y # CONFIG_CMD_BOOTM is not set +# CONFIG_CMD_ERRATA is not set # CONFIG_CMD_IMLS is not set CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set
configs/controlcenterd_TRAILBLAZER_defconfig +1 -0
@@ -8,6 +8,7 @@ CONFIG_SYS_CONSOLE_IS_IN_ENV=y # CONFIG_DISPLAY_BOARDINFO is not set CONFIG_BOARD_EARLY_INIT_F=y # CONFIG_CMD_BOOTM is not set +# CONFIG_CMD_ERRATA is not set # CONFIG_CMD_IMLS is not set CONFIG_CMD_EEPROM=y # CONFIG_CMD_FLASH is not set
include/configs/B4860QDS.h +0 -1
@@ -702,7 +702,6 @@ unsigned long get_board_ddr_clk(void);/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/BSC9131RDB.h +0 -1
@@ -293,7 +293,6 @@ extern unsigned long get_sdram_size(void);/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/BSC9132QDS.h +0 -1
@@ -521,7 +521,6 @@ combinations. this should be removed later/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/C29XPCIE.h +0 -1
@@ -436,7 +436,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/MPC8572DS.h +0 -1
@@ -547,7 +547,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/P1010RDB.h +0 -1
@@ -726,7 +726,6 @@ extern unsigned long get_sdram_size(void);/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/P1022DS.h +0 -1
@@ -593,7 +593,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/P2041RDB.h +0 -1
@@ -580,7 +580,6 @@ unsigned long get_board_sys_clk(unsigned long dummy);/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #ifdef CONFIG_PCI
include/configs/T102xQDS.h +0 -1
@@ -780,7 +780,6 @@ unsigned long get_board_ddr_clk(void);/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/T102xRDB.h +0 -1
@@ -790,7 +790,6 @@ unsigned long get_board_ddr_clk(void);/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/T1040QDS.h +0 -1
@@ -661,7 +661,6 @@ unsigned long get_board_ddr_clk(void);/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/T104xRDB.h +0 -1
@@ -774,7 +774,6 @@ $(SRCTREE)/board/freescale/t104xrdb/t1042d4_sd_rcw.cfg/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/T208xQDS.h +0 -1
@@ -745,7 +745,6 @@ unsigned long get_board_ddr_clk(void);/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/T208xRDB.h +0 -1
@@ -691,7 +691,6 @@ unsigned long get_board_ddr_clk(void);/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_REGINFO #ifdef CONFIG_PCI
include/configs/T4240RDB.h +0 -1
@@ -272,7 +272,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #ifdef CONFIG_PCI
include/configs/UCP1020.h +0 -1
@@ -424,7 +424,6 @@#define CONFIG_CMD_IRQ #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO -#define CONFIG_CMD_ERRATA /* * USB
include/configs/controlcenterd.h +0 -1
@@ -344,7 +344,6 @@#ifndef CONFIG_TRAILBLAZER -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/corenet_ds.h +0 -1
@@ -593,7 +593,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/cyrus.h +0 -1
@@ -411,7 +411,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #define CONFIG_CMD_REGINFO
include/configs/km/kmp204x-common.h +0 -1
@@ -370,7 +370,6 @@ int get_scl(void);* additionnal command line configuration. */ #define CONFIG_CMD_PCI -#define CONFIG_CMD_ERRATA /* we don't need flash support */ #undef CONFIG_FLASH_CFI_MTD
include/configs/t4qds.h +0 -1
@@ -241,7 +241,6 @@/* * Command line configuration. */ -#define CONFIG_CMD_ERRATA #define CONFIG_CMD_IRQ #ifdef CONFIG_PCI
scripts/config_whitelist.txt +0 -1
@@ -384,7 +384,6 @@ CONFIG_CM922T_XA10 CONFIG_CMDLINE_EDITING CONFIG_CMDLINE_PS_SUPPORT CONFIG_CMDLINE_TAG -CONFIG_CMD_ERRATA CONFIG_CMD_ESBC_VALIDATE CONFIG_CMD_ETHSW CONFIG_CMD_FDC
Signature · 1 line
2.13.0.rc2.291.g57267f2277-goog
PATCH 19/47 Convert CONFIG_CMD_ERRATA to Kconfig
Quoted 2 lines · Simon Glass
This converts the following to
Kconfig:
CONFIG_CMD_ERRATA
[snip]
arch/powerpc/cpu/mpc85xx/Kconfig menu "mpc85xx CPU" · line 10
Quoted 4 lines
arch/powerpc/cpu/mpc85xx/Kconfig +4
-0+config CMD_ERRATA + bool "Enable the 'errata' command" + depends on MPC85xx + default y if MPC85xx
This can just be default y
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170515/86ef8e5b/attachment.sig>