libata: prevent writes to read-only registers
cover libata: prevent writes to read-only registers
Recent Broadcom SoCs allow for the trapping of write accesses to read-only registers. This is only useful if such accesses are exceptional, so it is desirable to prevent such accesses in normal operation. To that end, this set of commits proposes adding two flags to the libata core.
The first allows for a quirk that exists in some Broadcom devices that are capable of supporting Aggresive Link Power Management even though it is not reported by their read-only capability register. This removes a need for the Broadcom driver to write to it's read-only capability register.
The second is a notification to the libata-core that it should not write to any standard registers that are defined to be read-only.
The Broadcom driver is then modified to use these two general purpose flags.
Doug Berger (3):
libata: Add the AHCI_HFLAG_YES_ALPM flag
libata: Add the AHCI_HFLAG_NO_WRITE_TO_RO flag
ata: ahci_brcm: Avoid writing to read-only registers
drivers/ata/ahci.h | 3 +++ drivers/ata/ahci_brcm.c | 12 ++++-------- drivers/ata/libahci.c | 8 +++++++- 3 files changed, 14 insertions(+), 9 deletions(-)
Signature · 1 line
2.13.0
PATCH 1/3 libata: Add the AHCI_HFLAG_YES_ALPM flag
Some hardware is capable of supporting Aggresive Link Power Management even though it is not indicated by the Host Capability register.
This commit adds the AHCI_HFLAG_YES_ALPM flag to the AHCI library to allow indication of this quirk when the Host Capability register is Read Only and therefore cannot be changed.
--- drivers/ata/ahci.h | 1 + drivers/ata/libahci.c | 5 +++++ 2 files changed, 6 insertions(+)
drivers/ata/ahci.h +1 -0
@@ -248,6 +248,7 @@ enum {AHCI_HFLAG_MULTI_MSI =0 , #endifAHCI_HFLAG_WAKE_BEFORE_STOP = (1 <<22 ),/* wake before DMA stop */ + AHCI_HFLAG_YES_ALPM = (1 << 23), /* force ALPM cap on *//* ap->flags bits */
drivers/ata/libahci.c +5 -0
@@ -504,6 +504,11 @@ void ahci_save_initial_config(struct device *dev, struct ahci_host_priv *hpriv) cap &= ~HOST_CAP_FBS ; } +if (!(cap &HOST_CAP_ALPM ) && (hpriv->flags &AHCI_HFLAG_YES_ALPM )) { +dev_info (dev,"controller can do ALPM, turning on CAP_ALPM\n" ); + cap |=HOST_CAP_ALPM ; + } +if (hpriv->force_port_map && port_map != hpriv->force_port_map) {dev_info (dev,"forcing port_map 0x%x -> 0x%x\n" , port_map, hpriv->force_port_map);
Signature · 1 line
2.13.0
PATCH 2/3 libata: Add the AHCI_HFLAG_NO_WRITE_TO_RO flag
In reply to Doug BergerWhile most hardware will simply ignore a write to a read-only register, some hardware will signal an abort if this occurs.
This commit introduces the flag AHCI_HFLAG_NO_WRITE_TO_RO to prevent the AHCI library from attempting to write to the HOST_CAP, HOST_CAP2, and HOST_PORTS_IMPL registers which may be read-only.
--- drivers/ata/ahci.h | 2 ++ drivers/ata/libahci.c | 3 ++- 2 files changed, 4 insertions(+), 1 deletion(-)
drivers/ata/ahci.h +2 -0
@@ -249,6 +249,8 @@ enum {#endif AHCI_HFLAG_WAKE_BEFORE_STOP = (1 <<22 ),/* wake before DMA stop */ AHCI_HFLAG_YES_ALPM = (1 <<23 ),/* force ALPM cap on */ + AHCI_HFLAG_NO_WRITE_TO_RO = (1 << 24), /* don't write to read +only registers */ /* ap->flags bits */
drivers/ata/libahci.c +2 -1
@@ -945,7 +945,8 @@ int ahci_reset_controller(struct ata_host *host)/* Some registers might be cleared on reset. Restore * initial values. */ -ahci_restore_initial_config (host); +if (!(hpriv->flags &AHCI_HFLAG_NO_WRITE_TO_RO )) +ahci_restore_initial_config (host); }else dev_info (host->dev,"skipping global host reset\n" );
Signature · 1 line
2.13.0
PATCH 3/3 ata: ahci_brcm: Avoid writing to read-only registers
In reply to Doug BergerThis commit makes use of the AHCI_HFLAG_YES_ALPM flag to prevent the driver from writing to the read-only Host Capability register.
It also sets the AHCI_HFLAG_NO_WRITE_TO_RO flag to prevent the AHCI library from writing to read-only registers.
--- drivers/ata/ahci_brcm.c | 12 ++++-------- 1 file changed, 4 insertions(+), 8 deletions(-)
drivers/ata/ahci_brcm.c +4 -8
@@ -39,7 +39,6 @@#define PIODATA_ENDIAN_SHIFT 6#define ENDIAN_SWAP_NONE 0#define ENDIAN_SWAP_FULL 2 -#define OVERRIDE_HWINIT BIT(16)#define SATA_TOP_CTRL_TP_CTRL 0x8#define SATA_TOP_CTRL_PHY_CTRL 0xc#define SATA_TOP_CTRL_PHY_CTRL_1 0x0
@@ -126,17 +125,13 @@ static inline void brcm_sata_writereg(u32 val, void __iomem *addr)static void brcm_sata_alpm_init (struct ahci_host_priv *hpriv) {struct brcm_ahci_priv *priv = hpriv->plat_data; -u32 bus_ctrl, port_ctrl, host_caps; +u32 port_ctrl, host_caps;int i;/* Enable support for ALPM */ - bus_ctrl =brcm_sata_readreg (priv->top_ctrl + -SATA_TOP_CTRL_BUS_CTRL ); -brcm_sata_writereg (bus_ctrl |OVERRIDE_HWINIT , - priv->top_ctrl +SATA_TOP_CTRL_BUS_CTRL ); host_caps =readl (hpriv->mmio +HOST_CAP ); -writel (host_caps |HOST_CAP_ALPM , hpriv->mmio); -brcm_sata_writereg (bus_ctrl, priv->top_ctrl +SATA_TOP_CTRL_BUS_CTRL ); +if (!(host_caps &HOST_CAP_ALPM )) + hpriv->flags |=AHCI_HFLAG_YES_ALPM ;/* * Adjust timeout to allow PLL sufficient time to lock while waking
@@ -360,6 +355,7 @@ static int brcm_ahci_probe(struct platform_device *pdev)if (priv->quirks &BRCM_AHCI_QUIRK_NO_NCQ ) hpriv->flags |=AHCI_HFLAG_NO_NCQ ; + hpriv->flags |=AHCI_HFLAG_NO_WRITE_TO_RO ; ret =ahci_platform_init_host (pdev, hpriv, &ahci_brcm_port_info, &ahci_platform_sht);
Signature · 1 line
2.13.0
Quoted 12 lines · Doug Berger
Recent Broadcom SoCs allow for the trapping of write accesses to read-only registers. This is only useful if such accesses are exceptional, so it is desirable to prevent such accesses in normal operation. To that end, this set of commits proposes adding two flags to the libata core.
The first allows for a quirk that exists in some Broadcom devices that are capable of supporting Aggresive Link Power Management even though it is not reported by their read-only capability register. This removes a need for the Broadcom driver to write to it's read-only capability register.
Quoted 5 lines
The second is a notification to the libata-core that it should not write to any standard registers that are defined to be read-only.
The Broadcom driver is then modified to use these two general purpose flags.
Applied 1-3 to libata/for-4.13.
Thanks.
Signature · 1 line
tejun