Skip to contentSkip to conversation

AM43xx EPOS EVM sleep pinmux

PATCH In review Andrew F. Davis 2 participants 13 messages Sep 29, 2017 – Oct 2, 2017 1 message not in the archive

Subsystems (2)
Device tree bindings Pin control
lore
Share & tools
lore

Andrew F. Davis

author
#0 lore raw

cover AM43xx EPOS EVM sleep pinmux

Hello all,

This series adds pinmux settings useful for DeepSleep modes. This brings the EPOS EVM more inline with the GP EVM in terms of DS0 DT support.

Thanks,
Andrew

Andrew F. Davis (10):
ARM: dts: am43xx: Introduce additional pinmux definitions for DS0
ARM: dts: am43xx-epos-evm: Add sleep pinmux for spi0 and spi1
ARM: dts: am43xx-epos-evm: Add sleep pinmux for qspi1
ARM: dts: am43xx-epos-evm: Add sleep pinmux for ecap0
ARM: dts: am43xx-epos-evm: Add sleep pinmux for gpmc
ARM: dts: am43xx-epos-evm: Add sleep pinmux for pixcir_ts
ARM: dts: am43xx-epos-evm: Add sleep pinmux for mmc1
ARM: dts: am43xx-epos-evm: Add default and sleep pinmux for uart0
ARM: dts: am43xx-epos-evm: Add default and sleep pinmux for usb2_phy1
and usb2_phy2
ARM: dts: am43xx-epos-evm: Add default pinmux for unused pins

Kabir Sahane (1):
ARM: dts: am43xx-epos-evm: Add default and sleep pinmux for
matrix_keypad0

 arch/arm/boot/dts/am43x-epos-evm.dts | 239 ++++++++++++++++++++++++++++++++---
 include/dt-bindings/pinctrl/am43xx.h |  12 ++
 2 files changed, 230 insertions(+), 21 deletions(-)
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

A message that is not in the archive (sent off-list or not yet received): [email protected]

author
#2 lore raw

PATCH 1/11 ARM: dts: am43xx: Introduce additional pinmux definitions for DS0

AM43xx platform pinmux registers contain bits to set state during suspend (DS0), add these bit definitions here.

Signed-off-by Andrew F. Davis <[email protected]>
---
 include/dt-bindings/pinctrl/am43xx.h | 12 ++++++++++++
 1 file changed, 12 insertions(+)
include/dt-bindings/pinctrl/am43xx.h +12 -0
index 344bd1eb3386..fc31ef7ce219 100644
@@ -21,9 +21,21 @@
 #define INPUT_EN		(1 << 18)
 #define SLEWCTRL_SLOW		(1 << 19)
 #define SLEWCTRL_FAST		0
+#define DS0_FORCE_OFF_MODE	(1 << 24)
+#define DS0_INPUT		(1 << 25)
+#define DS0_FORCE_OUT_HIGH	(1 << 26)
 #define DS0_PULL_UP_DOWN_EN	(1 << 27)
+#define DS0_PULL_UP_SEL		(1 << 28)
 #define WAKEUP_ENABLE		(1 << 29)
 
+#define DS0_PIN_OUTPUT		(DS0_FORCE_OFF_MODE)
+#define DS0_PIN_OUTPUT_HIGH	(DS0_FORCE_OFF_MODE | DS0_FORCE_OUT_HIGH)
+#define DS0_PIN_OUTPUT_PULLUP	(DS0_FORCE_OFF_MODE | DS0_PULL_UP_DOWN_EN | DS0_PULL_UP_SEL)
+#define DS0_PIN_OUTPUT_PULLDOWN	(DS0_FORCE_OFF_MODE | DS0_PULL_UP_DOWN_EN)
+#define DS0_PIN_INPUT		(DS0_FORCE_OFF_MODE | DS0_INPUT)
+#define DS0_PIN_INPUT_PULLUP	(DS0_FORCE_OFF_MODE | DS0_INPUT | DS0_PULL_UP_DOWN_EN | DS0_PULL_UP_SEL)
+#define DS0_PIN_INPUT_PULLDOWN	(DS0_FORCE_OFF_MODE | DS0_INPUT | DS0_PULL_UP_DOWN_EN)
+
 #define PIN_OUTPUT		(PULL_DISABLE)
 #define PIN_OUTPUT_PULLUP	(PULL_UP)
 #define PIN_OUTPUT_PULLDOWN	0
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#3 lore raw

PATCH 2/11 ARM: dts: am43xx-epos-evm: Add sleep pinmux for spi0 and spi1

In reply to a message not in the archive
Signed-off-by Andrew F. Davis <[email protected]>
---
 arch/arm/boot/dts/am43x-epos-evm.dts | 32 ++++++++++++++++++++++++++------
 1 file changed, 26 insertions(+), 6 deletions(-)
arch/arm/boot/dts/am43x-epos-evm.dts +26 -6
index 9d276af7c539..f73c22ce4003 100644
@@ -232,7 +232,7 @@
 			>;
 		};
 
-		spi0_pins: pinmux_spi0_pins {
+		spi0_pins_default: pinmux_spi0_pins_default {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x950, PIN_INPUT | MUX_MODE0)           /* spi0_clk.spi0_clk */
 				AM4372_IOPAD(0x954, PIN_OUTPUT | MUX_MODE0)           /* spi0_d0.spi0_d0 */

@@ -241,7 +241,16 @@
 			>;
 		};
 
-		spi1_pins: pinmux_spi1_pins {
+		spi0_pins_sleep: pinmux_spi0_pins_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x950, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x954, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x958, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x95c, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)
+			>;
+		};
+
+		spi1_pins_default: pinmux_spi1_pins_default {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x990, PIN_INPUT | MUX_MODE3)           /* mcasp0_aclkx.spi1_clk */
 				AM4372_IOPAD(0x994, PIN_OUTPUT | MUX_MODE3)           /* mcasp0_fsx.spi1_d0 */

@@ -250,6 +259,15 @@
 			>;
 		};
 
+		spi1_pins_sleep: pinmux_spi1_pins_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x990, DS0_PIN_OUTPUT_PULLDOWN | PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x994, DS0_PIN_OUTPUT_PULLDOWN | PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x998, DS0_PIN_OUTPUT_PULLDOWN | PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x99c, DS0_PIN_OUTPUT_PULLDOWN | PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
 		mmc1_pins: pinmux_mmc1_pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */

@@ -656,15 +674,17 @@
 };
 
 &spi0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi0_pins>;
 	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi0_pins_default>;
+	pinctrl-1 = <&spi0_pins_sleep>;
 };
 
 &spi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi1_pins>;
 	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi1_pins_default>;
+	pinctrl-1 = <&spi1_pins_sleep>;
 };
 
 &usb2_phy1 {
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#4 lore raw

PATCH 3/11 ARM: dts: am43xx-epos-evm: Add sleep pinmux for qspi1

In reply to a message not in the archive
Signed-off-by Andrew F. Davis <[email protected]>
---
 arch/arm/boot/dts/am43x-epos-evm.dts | 18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)
arch/arm/boot/dts/am43x-epos-evm.dts +15 -3
index f73c22ce4003..2b9ea3810fcc 100644
@@ -274,7 +274,7 @@
 			>;
 		};
 
-		qspi1_default: qspi1_default {
+		qspi1_pins_default: qspi1_pins_default {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x87c, PIN_INPUT_PULLUP | MUX_MODE3)
 				AM4372_IOPAD(0x888, PIN_INPUT_PULLUP | MUX_MODE2)

@@ -285,6 +285,17 @@
 			>;
 		};
 
+		qspi1_pins_sleep: qspi1_pins_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x87c, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x888, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x890, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x894, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x898, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x89c, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+			>;
+		};
+
 		pixcir_ts_pins: pixcir_ts_pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_a1.gpio1_17 */

@@ -707,8 +718,9 @@
 
 &qspi {
 	status = "disabled";	/* Disable GPMC (NAND) when enabling QSPI */
-	pinctrl-names = "default";
-	pinctrl-0 = <&qspi1_default>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi1_pins_default>;
+	pinctrl-1 = <&qspi1_pins_sleep>;
 
 	spi-max-frequency = <48000000>;
 	m25p80@0 {
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#5 lore raw

PATCH 4/11 ARM: dts: am43xx-epos-evm: Add sleep pinmux for ecap0

In reply to a message not in the archive
Signed-off-by Andrew F. Davis <[email protected]>
---
 arch/arm/boot/dts/am43x-epos-evm.dts | 13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)
arch/arm/boot/dts/am43x-epos-evm.dts +10 -3
index 2b9ea3810fcc..8f9c901b0ccd 100644
@@ -219,12 +219,18 @@
 			>;
 		};
 
-		ecap0_pins: backlight_pins {
+		ecap0_pins_default: backlight_pins_default {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x964, MUX_MODE0)         /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
 			>;
 		};
 
+		ecap0_pins_sleep: backlight_pins_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x964, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+			>;
+		};
+
 		i2c2_pins: pinmux_i2c2_pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x9c0, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_sda.i2c2_sda */

@@ -680,8 +686,9 @@
 
 &ecap0 {
 		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&ecap0_pins>;
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&ecap0_pins_default>;
+		pinctrl-1 = <&ecap0_pins_sleep>;
 };
 
 &spi0 {
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#6 lore raw

PATCH 5/11 ARM: dts: am43xx-epos-evm: Add sleep pinmux for gpmc

In reply to a message not in the archive
Signed-off-by Andrew F. Davis <[email protected]>
---
 arch/arm/boot/dts/am43x-epos-evm.dts | 28 +++++++++++++++++++++++++---
 1 file changed, 25 insertions(+), 3 deletions(-)
arch/arm/boot/dts/am43x-epos-evm.dts +25 -3
index 8f9c901b0ccd..822e54cffd29 100644
@@ -198,7 +198,7 @@
 			>;
 		};
 
-		nand_flash_x8: nand_flash_x8 {
+		nand_flash_x8_default: nand_flash_x8_default {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x840, PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a0.SELQSPIorNAND/GPIO */
 				AM4372_IOPAD(0x800, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */

@@ -219,6 +219,27 @@
 			>;
 		};
 
+		nand_flash_x8_sleep: nand_flash_x8_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x840, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x800, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x804, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x808, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x80c, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x810, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x814, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x818, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x81c, DS0_PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x870, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x874, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x87c, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x890, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x894, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x898, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x89c, DS0_PIN_OUTPUT_PULLUP | MUX_MODE7)
+			>;
+		};
+
 		ecap0_pins_default: backlight_pins_default {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x964, MUX_MODE0)         /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */

@@ -589,8 +610,9 @@
 
 &gpmc {
 	status = "okay";	/* Disable QSPI when enabling GPMC (NAND) */
-	pinctrl-names = "default";
-	pinctrl-0 = <&nand_flash_x8>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&nand_flash_x8_default>;
+	pinctrl-1 = <&nand_flash_x8_sleep>;
 	ranges = <0 0 0x08000000 0x01000000>;	/* CS0 space. Min partition = 16MB */
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#7 lore raw

PATCH 6/11 ARM: dts: am43xx-epos-evm: Add sleep pinmux for pixcir_ts

In reply to a message not in the archive
Signed-off-by Andrew F. Davis <[email protected]>
---
 arch/arm/boot/dts/am43x-epos-evm.dts | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)
arch/arm/boot/dts/am43x-epos-evm.dts +11 -3
index 822e54cffd29..9c4ac6f715ec 100644
@@ -323,12 +323,18 @@
 			>;
 		};
 
-		pixcir_ts_pins: pixcir_ts_pins {
+		pixcir_ts_pins_default: pixcir_ts_pins_default {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_a1.gpio1_17 */
 			>;
 		};
 
+		pixcir_ts_pins_sleep: pixcir_ts_pins_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x844, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_a1.gpio1_17 */
+			>;
+		};
+
 		hdq_pins: pinmux_hdq_pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0xa34, PIN_INPUT_PULLUP | MUX_MODE1)    /* cam1_wen.hdq_gpio */

@@ -538,8 +544,10 @@
 
 	pixcir_ts@5c {
 		compatible = "pixcir,pixcir_tangoc";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pixcir_ts_pins>;
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pixcir_ts_pins_default>;
+		pinctrl-1 = <&pixcir_ts_pins_sleep>;
+
 		reg = <0x5c>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#8 lore raw

PATCH 7/11 ARM: dts: am43xx-epos-evm: Add sleep pinmux for mmc1

In reply to a message not in the archive
Signed-off-by Andrew F. Davis <[email protected]>
---
 arch/arm/boot/dts/am43x-epos-evm.dts | 13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)
arch/arm/boot/dts/am43x-epos-evm.dts +10 -3
index 9c4ac6f715ec..4d5487b853c3 100644
@@ -295,12 +295,18 @@
 			>;
 		};
 
-		mmc1_pins: pinmux_mmc1_pins {
+		mmc1_pins_default: pinmux_mmc1_pins_default {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x960, PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
 			>;
 		};
 
+		mmc1_pins_sleep: pinmux_mmc1_pins_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x960, DS0_PIN_OUTPUT_PULLUP | PIN_INPUT | MUX_MODE7)
+			>;
+		};
+
 		qspi1_pins_default: qspi1_pins_default {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x87c, PIN_INPUT_PULLUP | MUX_MODE3)

@@ -440,8 +446,9 @@
 	status = "okay";
 	vmmc-supply = <&vmmcsd_fixed>;
 	bus-width = <4>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_sleep>;
 	cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
 };
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#9 lore raw

PATCH 8/11 ARM: dts: am43xx-epos-evm: Add default and sleep pinmux for matrix_keypad0

In reply to a message not in the archive

From: Kabir Sahane <[email protected]>

Signed-off-by Kabir Sahane <[email protected]>
Signed-off-by Andrew F. Davis <[email protected]>
---
 arch/arm/boot/dts/am43x-epos-evm.dts | 29 +++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)
arch/arm/boot/dts/am43x-epos-evm.dts +29 -0
index 4d5487b853c3..569c9ac200c8 100644
@@ -75,6 +75,9 @@
 		compatible = "gpio-matrix-keypad";
 		debounce-delay-ms = <5>;
 		col-scan-delay-us = <2>;
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&matrix_keypad_default>;
+		pinctrl-1 = <&matrix_keypad_sleep>;
 
 		row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH		/* Bank0, pin12 */
 			     &gpio0 13 GPIO_ACTIVE_HIGH		/* Bank0, pin13 */

@@ -307,6 +310,32 @@
 			>;
 		};
 
+		matrix_keypad_default: matrix_keypad_default {
+			pinctrl-single,pins = <
+				 AM4372_IOPAD(0x92c, PIN_OUTPUT | MUX_MODE7)          /* mii1_tx_clk.gpio3_9 */
+				 AM4372_IOPAD(0x930, PIN_OUTPUT | MUX_MODE7)          /* mii1_rx_clk.gpio3_10 */
+				 AM4372_IOPAD(0x934, PIN_OUTPUT | MUX_MODE7)          /* mii1_rxd3.gpio2_18 */
+				 AM4372_IOPAD(0x938, PIN_OUTPUT | MUX_MODE7)          /* mii1_rxd2.gpio2_19 */
+				 AM4372_IOPAD(0x978, PIN_INPUT_PULLDOWN | MUX_MODE7)  /* uart1_ctsn.gpio0_12 */
+				 AM4372_IOPAD(0x97C, PIN_INPUT_PULLDOWN | MUX_MODE7)  /* uart1_rtsn.gpio0_13 */
+				 AM4372_IOPAD(0x980, PIN_INPUT_PULLDOWN | MUX_MODE7)  /* uart1_rxd.gpio0_14 */
+				 AM4372_IOPAD(0x984, PIN_INPUT_PULLDOWN | MUX_MODE7)  /* uart1_txd.gpio0_15 */
+			>;
+		};
+
+		matrix_keypad_sleep: matrix_keypad_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x930, PIN_INPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x938, PIN_INPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x978, PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x97C, PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x980, PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x984, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
 		qspi1_pins_default: qspi1_pins_default {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x87c, PIN_INPUT_PULLUP | MUX_MODE3)
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#10 lore raw

PATCH 9/11 ARM: dts: am43xx-epos-evm: Add default and sleep pinmux for uart0

In reply to a message not in the archive
Signed-off-by Andrew F. Davis <[email protected]>
---
 arch/arm/boot/dts/am43x-epos-evm.dts | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)
arch/arm/boot/dts/am43x-epos-evm.dts +25 -0
index 569c9ac200c8..ce7a44daf839 100644
@@ -452,6 +452,24 @@
 			>;
 		};
 
+		uart0_pins_default: uart0_pins_default {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0) /* uart0_ctsn.uart0_ctsn */
+				AM4372_IOPAD(0x96C, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE0) /* uart0_rtsn.uart0_rtsn */
+				AM4372_IOPAD(0x970, PIN_INPUT_PULLUP | SLEWCTRL_FAST | DS0_PULL_UP_DOWN_EN | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+				AM4372_IOPAD(0x974, PIN_INPUT | SLEWCTRL_FAST | DS0_PULL_UP_DOWN_EN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+			>;
+		};
+
+		uart0_pins_sleep: uart0_pins_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+				AM4372_IOPAD(0x96C, DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)
+				AM4372_IOPAD(0x970, PIN_INPUT_PULLUP | SLEWCTRL_FAST | DS0_PULL_UP_DOWN_EN | MUX_MODE0)
+				AM4372_IOPAD(0x974, PIN_INPUT | SLEWCTRL_FAST | DS0_PULL_UP_DOWN_EN | MUX_MODE0)
+			>;
+		};
+
 		mcasp1_pins: mcasp1_pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x9a0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* MCASP0_ACLKR/MCASP1_ACLKX */

@@ -879,6 +897,13 @@
 	};
 };
 
+&uart0 {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&uart0_pins_default>;
+	pinctrl-1 = <&uart0_pins_sleep>;
+};
+
 &mcasp1 {
 	#sound-dai-cells = <0>;
 	pinctrl-names = "default", "sleep";
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#11 lore raw

PATCH 10/11 ARM: dts: am43xx-epos-evm: Add default and sleep pinmux for usb2_phy1 and usb2_phy2

In reply to a message not in the archive
Signed-off-by Andrew F. Davis <[email protected]>
---
 arch/arm/boot/dts/am43x-epos-evm.dts | 30 ++++++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
arch/arm/boot/dts/am43x-epos-evm.dts +30 -0
index ce7a44daf839..e745a038c222 100644
@@ -470,6 +470,30 @@
 			>;
 		};
 
+		usb2_phy1_default: usb2_phy1_default {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0xac0, PIN_INPUT_PULLDOWN | MUX_MODE0)
+			>;
+		};
+
+		usb2_phy1_sleep: usb2_phy1_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0xac0, DS0_PULL_UP_DOWN_EN | PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
+		usb2_phy2_default: usb2_phy2_default {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0xac4, PIN_INPUT_PULLDOWN | MUX_MODE0)
+			>;
+		};
+
+		usb2_phy2_sleep: usb2_phy2_sleep {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0xac4, DS0_PULL_UP_DOWN_EN | PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
 		mcasp1_pins: mcasp1_pins {
 			pinctrl-single,pins = <
 				AM4372_IOPAD(0x9a0, PIN_INPUT_PULLDOWN | MUX_MODE3) /* MCASP0_ACLKR/MCASP1_ACLKX */

@@ -791,6 +815,9 @@
 
 &usb2_phy1 {
 	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usb2_phy1_default>;
+	pinctrl-1 = <&usb2_phy1_sleep>;
 };
 
 &usb1 {

@@ -800,6 +827,9 @@
 
 &usb2_phy2 {
 	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usb2_phy2_default>;
+	pinctrl-1 = <&usb2_phy2_sleep>;
 };
 
 &usb2 {
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
author
#12 lore raw

PATCH 11/11 ARM: dts: am43xx-epos-evm: Add default pinmux for unused pins

In reply to a message not in the archive

Give unused pins a power-friendly default pinmux setting.

Signed-off-by Andrew F. Davis <[email protected]>
---
 arch/arm/boot/dts/am43x-epos-evm.dts | 37 ++++++++++++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)
arch/arm/boot/dts/am43x-epos-evm.dts +37 -0
index e745a038c222..4146dd66ad88 100644
@@ -148,6 +148,43 @@
 };
 
 &am43xx_pinmux {
+		pinctrl-names = "default";
+		pinctrl-0 = <&unused_pins>;
+
+		unused_pins: unused_pins {
+			pinctrl-single,pins = <
+				AM4372_IOPAD(0x848, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x850, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x858, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x860, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x864, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x868, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x86c, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x878, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0x908, DS0_PIN_INPUT_PULLDOWN | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x91c, DS0_PIN_OUTPUT_PULLDOWN | PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x920, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0x9e0, DS0_PIN_INPUT_PULLDOWN | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA0c, DS0_PIN_OUTPUT_PULLDOWN | PIN_OUTPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA38, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA3c, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA40, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA44, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA48, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA4c, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA50, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA54, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA58, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA5c, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA60, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA64, DS0_PIN_OUTPUT_PULLUP | PIN_OUTPUT_PULLUP | MUX_MODE7)
+				AM4372_IOPAD(0xA68, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA6C, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA74, DS0_PIN_INPUT_PULLDOWN | PIN_INPUT_PULLDOWN | MUX_MODE7)
+				AM4372_IOPAD(0xA78, DS0_PIN_INPUT | PIN_INPUT_PULLDOWN | MUX_MODE7)
+			>;
+		};
+
 		cpsw_default: cpsw_default {
 			pinctrl-single,pins = <
 				/* Slave 1 */
Signature · 6 lines
2.14.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
#13 lore raw
In reply to a message not in the archive
Quoted 5 lines · Andrew F. Davis

Hello all,

This series adds pinmux settings useful for DeepSleep modes. This brings the EPOS EVM more inline with the GP EVM in terms of DS0 DT support.

Applying all into omap-for-v4.15/dt thanks.

Tony
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html