Skip to contentSkip to conversation

Renesas ARM64 Based SoC DT Updates for v4.15

GIT PULL New Simon Horman 6 participants 33 messages Sep 29, 2017 – Oct 20, 2017

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

Hi Olof, Hi Kevin, Hi Arnd,

Please consider these Renesas ARM64 based SoC DT updates for v4.15.

The following changes since commit 2bd6bf03f4c1c59381d62c61d03f6cc3fe71f66e:

Linux 4.14-rc1 (2017-09-16 15:47:51 -0700)

are available in the git repository at:

https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt-for-v4.15

for you to fetch changes up to 2affee619d48d101831e83e74cadeb7c5200d9cb:

arm64: dts: renesas: r8a7796: add USB3.0 peripheral device node (2017-09-25 09:09:51 +0200)

----------------------------------------------------------------
Renesas ARM64 Based SoC DT Updates for v4.15

* r8a7795 (H3)
- Use r8a7795-cpg-mssr and r8a7795-sysc bindings
Hardcoded indicies are replaced with symbols now that they are available

- Drop bogus HDMI node name suffixes
Laurent Pinchart says: Node names should not use numerical suffixes if the nodes can be distinguished by unit-address

- Update PFC node name to pin-controller
Shimoda-san says the PFC node name is changed "from e6060000.pfc and pfc at e6060000 to e6060000.pin-controller and pin-controller at e6060000 like other Renesas SoCs."

* r8a7795 (H3) ES1.0
- Drop extra zero from XHCI unit address
This corrects a typo were ee0400000 rather than ee040000 was used as the unit address.

* r8a7796 (M3-W)
- Add FDP1 instance
Laurent Pinchart says: The r8a7796 has a single FDP1 instance.

* r8a7795 (H3) and r8a7796 (M3-W) SoCs
- Add USB3.0 peripheral device nodes
Shimoda-san says that this is not enabled on the Salvator-X/XS boards for now as:
+ we need a special cable (USB type-A to A cross cable).
+ we can swap the role by renesas_usb3 driver even if we use a normal cable and after usb3.0 host is running, but I think it's a special use case.

* r8a7795 (H3) and r8a7796 (M3-W) ULCB boards
- Enable display output
Laurent Pinchart says: The DU is already wired up to the HDMI encoder, all we need to do is enable it.

* r8a77995 (D3) Draak board
- Enable EthernetAVB and , USB2.0 Host and PHY

- Add serial console pins.
This is safe to do now that r8a77995 PFC driver support is present

* r8a77970 (V3M)
- Add basic support for SoC and EtherAVB, [H]SCIF and SYS-DMAC nodes This is a step towards enabling EtherAVB and [H]SCIF with SYS-DMAC in the Eagle board support for which is under review

----------------------------------------------------------------
Geert Uytterhoeven (6):
arm64: dts: renesas: r8a7795-es1: Drop extra zero from usb unit address
arm64: dts: renesas: r8a7795: Drop bogus HDMI node names suffixes
arm64: renesas: Add Renesas R8A77970 Kconfig support
arm64: dts: renesas: r8a77995: Use r8a7795-sysc binding definitions
arm64: dts: renesas: r8a77995: Use r8a7795-cpg-mssr binding definitions
arm64: dts: draak: Add serial console pins

Laurent Pinchart (2):
arm64: dts: renesas: r8a7796: Add FDP1 instance
arm64: dts: renesas: ulcb: Enable display output

Sergei Shtylyov (4):
arm64: dts: renesas: initial R8A77970 SoC device tree
arm64: dts: renesas: r8a77970: add SYS-DMAC support
arm64: dts: renesas: r8a77970: add [H]SCIF support
arm64: dts: renesas: r8a77970: add EtherAVB support

Yoshihiro Shimoda (10):
arm64: dts: renesas: r8a77995: update PFC node name to pin-controller
arm64: dts: renesas: r8a77995: add GPIO device nodes
arm64: dts: renesas: r8a77995: Add EthernetAVB device node
arm64: dts: renesas: r8a77995: Add USB2.0 PHY device node
arm64: dts: renesas: r8a77995: add USB2.0 Host (EHCI/OHCI) device node
arm64: dts: renesas: r8a77995: draak: enable USB2.0 PHY
arm64: dts: renesas: r8a77995: draak: enable USB2.0 Host (EHCI/OHCI)
arm64: dts: renesas: r8a77995: draak: enable EthernetAVB
arm64: dts: renesas: r8a7795: add USB3.0 peripheral device node
arm64: dts: renesas: r8a7796: add USB3.0 peripheral device node

 arch/arm64/Kconfig.platforms                   |   6 +
 arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi   |   2 +-
 arch/arm64/boot/dts/renesas/r8a7795.dtsi       |  15 +-
 arch/arm64/boot/dts/renesas/r8a7796.dtsi       |  21 ++
 arch/arm64/boot/dts/renesas/r8a77970.dtsi      | 366 +++++++++++++++++++++++++
 arch/arm64/boot/dts/renesas/r8a77995-draak.dts |  55 ++++
 arch/arm64/boot/dts/renesas/r8a77995.dtsi      | 211 +++++++++++++-
 arch/arm64/boot/dts/renesas/ulcb.dtsi          |   4 +
 8 files changed, 669 insertions(+), 11 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a77970.dtsi
#1 lore raw

PATCH 1/22 arm64: dts: renesas: r8a7795-es1: Drop extra zero from usb unit address

From: Geert Uytterhoeven <[email protected]>

With W=1:

    arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (simple_bus_reg): Node /soc/usb at ee0400000 simple-bus unit address format error, expected "ee040000"
    arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dtb: Warning (simple_bus_reg): Node /soc/usb at ee0400000 simple-bus unit address format error, expected "ee040000"
Fixes 291e0c4994d0813f ("arm64: dts: r8a7795: Add support for R-Car H3 ES2.0")
Fixes 171f2ef82284f61b ("arm64: dts: r8a7795: Add USB3.0 host device nodes")
---
 arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi +1 -1
index aaa5e67a963e..655dd30639c5 100644
@@ -11,7 +11,7 @@
 #include "r8a7795.dtsi"
 
 &soc {
-	xhci1: usb at ee0400000 {
+	xhci1: usb at ee040000 {
 		compatible = "renesas,xhci-r8a7795", "renesas,rcar-gen3-xhci";
 		reg = <0 0xee040000 0 0xc00>;
 		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
Signature · 1 line
2.1.4
#2 lore raw

PATCH 2/22 arm64: dts: renesas: r8a7796: Add FDP1 instance

In reply to Simon Horman

From: Laurent Pinchart <[email protected]>

The r8a7796 has a single FDP1 instance.

---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)
arch/arm64/boot/dts/renesas/r8a7796.dtsi +10 -0
index 369092e17e34..16da83458f18 100644
@@ -1659,6 +1659,16 @@
 			/* placeholder */
 		};
 
+		fdp1 at fe940000 {
+			compatible = "renesas,fdp1";
+			reg = <0 0xfe940000 0 0x2400>;
+			interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 119>;
+			power-domains = <&sysc R8A7796_PD_A3VC>;
+			resets = <&cpg 119>;
+			renesas,fcp = <&fcpf0>;
+		};
+
 		fcpf0: fcp at fe950000 {
 			compatible = "renesas,fcpf";
 			reg = <0 0xfe950000 0 0x200>;
Signature · 1 line
2.1.4
#3 lore raw

PATCH 3/22 arm64: dts: renesas: r8a77995: update PFC node name to pin-controller

In reply to Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch changes the name from from e6060000.pfc and pfc at e6060000 to e6060000.pin-controller and pin-controller at e6060000 like other Renesas SoCs.

---
 arch/arm64/boot/dts/renesas/r8a77995.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/renesas/r8a77995.dtsi +1 -1
index d0f95b78c022..72c303362b16 100644
@@ -122,7 +122,7 @@
 			reg = <0 0xe6160000 0 0x0200>;
 		};
 
-		pfc: pfc at e6060000 {
+		pfc: pin-controller at e6060000 {
 			compatible = "renesas,pfc-r8a77995";
 			reg = <0 0xe6060000 0 0x508>;
 		};
Signature · 1 line
2.1.4
#4 lore raw

PATCH 4/22 arm64: dts: renesas: ulcb: Enable display output

In reply to Simon Horman

From: Laurent Pinchart <[email protected]>

The DU is already wired up to the HDMI encoder, all we need to do is enable it.

---
 arch/arm64/boot/dts/renesas/ulcb.dtsi | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/renesas/ulcb.dtsi +4 -0
index 1b868df2393f..dfec9072718b 100644
@@ -157,6 +157,10 @@
 	};
 };
 
+&du {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
Signature · 1 line
2.1.4
#5 lore raw

PATCH 5/22 arm64: dts: renesas: r8a7795: Drop bogus HDMI node names suffixes

In reply to Simon Horman

From: Geert Uytterhoeven <[email protected]>

Node names should not use numerical suffixes if the nodes can be distinguished by unit-address.

---
 arch/arm64/boot/dts/renesas/r8a7795.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/renesas/r8a7795.dtsi +2 -2
index 2938195b9571..5d5174d8635d 100644
@@ -2014,7 +2014,7 @@
 			renesas,fcp = <&fcpf1>;
 		};
 
-		hdmi0: hdmi0 at fead0000 {
+		hdmi0: hdmi at fead0000 {
 			compatible = "renesas,r8a7795-hdmi", "renesas,rcar-gen3-hdmi";
 			reg = <0 0xfead0000 0 0x10000>;
 			interrupts = <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>;
@@ -2039,7 +2039,7 @@
 			};
 		};
 
-		hdmi1: hdmi1 at feae0000 {
+		hdmi1: hdmi at feae0000 {
 			compatible = "renesas,r8a7795-hdmi", "renesas,rcar-gen3-hdmi";
 			reg = <0 0xfeae0000 0 0x10000>;
 			interrupts = <GIC_SPI 436 IRQ_TYPE_LEVEL_HIGH>;
Signature · 1 line
2.1.4
#6 lore raw

PATCH 6/22 arm64: renesas: Add Renesas R8A77970 Kconfig support

In reply to Simon Horman

From: Geert Uytterhoeven <[email protected]>

Add a configuration option for the R-Car V3M SoC.

---
 arch/arm64/Kconfig.platforms | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm64/Kconfig.platforms +6 -0
index 6b54ee8c1262..a07f9b5a4f82 100644
@@ -184,6 +184,12 @@ config ARCH_R8A7796
 	help
 	  This enables support for the Renesas R-Car M3-W SoC.
 
+config ARCH_R8A77970
+	bool "Renesas R-Car V3M SoC Platform"
+	depends on ARCH_RENESAS
+	help
+	  This enables support for the Renesas R-Car V3M SoC.
+
 config ARCH_R8A77995
 	bool "Renesas R-Car D3 SoC Platform"
 	depends on ARCH_RENESAS
Signature · 1 line
2.1.4
#7 lore raw

PATCH 7/22 arm64: dts: renesas: r8a77995: Use r8a7795-sysc binding definitions

In reply to Simon Horman

From: Geert Uytterhoeven <[email protected]>

Replace the hardcoded power domain indices by R8A77995_PD_* symbols.

---
 arch/arm64/boot/dts/renesas/r8a77995.dtsi | 11 ++++++-----
 1 file changed, 6 insertions(+), 5 deletions(-)
arch/arm64/boot/dts/renesas/r8a77995.dtsi +6 -5
index 72c303362b16..a5b769b840e9 100644
@@ -11,6 +11,7 @@
 
 #include <dt-bindings/clock/renesas-cpg-mssr.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a77995-sysc.h>
 
 / {
 	compatible = "renesas,r8a77995";
@@ -30,14 +31,14 @@
 			compatible = "arm,cortex-a53", "arm,armv8";
 			reg = <0x0>;
 			device_type = "cpu";
-			power-domains = <&sysc 5>;
+			power-domains = <&sysc R8A77995_PD_CA53_CPU0>;
 			next-level-cache = <&L2_CA53>;
 			enable-method = "psci";
 		};
 
 		L2_CA53: cache-controller-1 {
 			compatible = "cache";
-			power-domains = <&sysc 21>;
+			power-domains = <&sysc R8A77995_PD_CA53_SCU>;
 			cache-unified;
 			cache-level = <2>;
 		};
@@ -76,7 +77,7 @@
 					(GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&cpg CPG_MOD 408>;
 			clock-names = "clk";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
 			resets = <&cpg 408>;
 		};
 
@@ -97,7 +98,7 @@
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
 			clocks = <&cpg CPG_MOD 402>;
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
 			status = "disabled";
 		};
@@ -147,7 +148,7 @@
 				 <&cpg CPG_CORE 16>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
-			power-domains = <&sysc 32>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
 			resets = <&cpg 310>;
 			status = "disabled";
 		};
Signature · 1 line
2.1.4
#8 lore raw

PATCH 8/22 arm64: dts: renesas: r8a77995: Use r8a7795-cpg-mssr binding definitions

In reply to Simon Horman

From: Geert Uytterhoeven <[email protected]>

Replace the hardcoded clock indices by R8A77995_CLK_* symbols.

---
 arch/arm64/boot/dts/renesas/r8a77995.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/renesas/r8a77995.dtsi +2 -2
index a5b769b840e9..84b6bd58eafb 100644
@@ -9,7 +9,7 @@
  * kind, whether express or implied.
  */
 
-#include <dt-bindings/clock/renesas-cpg-mssr.h>
+#include <dt-bindings/clock/r8a77995-cpg-mssr.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/power/r8a77995-sysc.h>
 
@@ -145,7 +145,7 @@
 			reg = <0 0xe6e88000 0 64>;
 			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 310>,
-				 <&cpg CPG_CORE 16>,
+				 <&cpg CPG_CORE R8A77995_CLK_S3D1C>,
 				 <&scif_clk>;
 			clock-names = "fck", "brg_int", "scif_clk";
 			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
Signature · 1 line
2.1.4
#9 lore raw

PATCH 9/22 arm64: dts: renesas: r8a77995: add GPIO device nodes

In reply to Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch adds GPIO device nodes for r8a77995.

---
 arch/arm64/boot/dts/renesas/r8a77995.dtsi | 112 ++++++++++++++++++++++++++++++
 1 file changed, 112 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995.dtsi +112 -0
index 84b6bd58eafb..d7756256d2a6 100644
@@ -139,6 +139,118 @@
 			#power-domain-cells = <1>;
 		};
 
+		gpio0: gpio at e6050000 {
+			compatible = "renesas,gpio-r8a77995",
+				     "renesas,rcar-gen3-gpio",
+				     "renesas,gpio-rcar";
+			reg = <0 0xe6050000 0 0x50>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 0 9>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 912>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 912>;
+		};
+
+		gpio1: gpio at e6051000 {
+			compatible = "renesas,gpio-r8a77995",
+				     "renesas,rcar-gen3-gpio",
+				     "renesas,gpio-rcar";
+			reg = <0 0xe6051000 0 0x50>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 32 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 911>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 911>;
+		};
+
+		gpio2: gpio at e6052000 {
+			compatible = "renesas,gpio-r8a77995",
+				     "renesas,rcar-gen3-gpio",
+				     "renesas,gpio-rcar";
+			reg = <0 0xe6052000 0 0x50>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 64 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 910>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 910>;
+		};
+
+		gpio3: gpio at e6053000 {
+			compatible = "renesas,gpio-r8a77995",
+				     "renesas,rcar-gen3-gpio",
+				     "renesas,gpio-rcar";
+			reg = <0 0xe6053000 0 0x50>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 96 10>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 909>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 909>;
+		};
+
+		gpio4: gpio at e6054000 {
+			compatible = "renesas,gpio-r8a77995",
+				     "renesas,rcar-gen3-gpio",
+				     "renesas,gpio-rcar";
+			reg = <0 0xe6054000 0 0x50>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 128 32>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 908>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 908>;
+		};
+
+		gpio5: gpio at e6055000 {
+			compatible = "renesas,gpio-r8a77995",
+				     "renesas,rcar-gen3-gpio",
+				     "renesas,gpio-rcar";
+			reg = <0 0xe6055000 0 0x50>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 160 21>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 907>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 907>;
+		};
+
+		gpio6: gpio at e6055400 {
+			compatible = "renesas,gpio-r8a77995",
+				     "renesas,rcar-gen3-gpio",
+				     "renesas,gpio-rcar";
+			reg = <0 0xe6055400 0 0x50>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			gpio-ranges = <&pfc 0 192 14>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			clocks = <&cpg CPG_MOD 906>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 906>;
+		};
+
 		scif2: serial at e6e88000 {
 			compatible = "renesas,scif-r8a77995",
 				     "renesas,rcar-gen3-scif", "renesas,scif";
Signature · 1 line
2.1.4
#10 lore raw

PATCH 10/22 arm64: dts: renesas: r8a77995: Add EthernetAVB device node

In reply to Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch adds EthernetAVB device node for r8a77995.

---
 arch/arm64/boot/dts/renesas/r8a77995.dtsi | 45 +++++++++++++++++++++++++++++++
 1 file changed, 45 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995.dtsi +45 -0
index d7756256d2a6..72d04d7337be 100644
@@ -251,6 +251,51 @@
 			resets = <&cpg 906>;
 		};
 
+		avb: ethernet at e6800000 {
+			compatible = "renesas,etheravb-r8a77995",
+				     "renesas,etheravb-rcar-gen3";
+			reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14", "ch15",
+					  "ch16", "ch17", "ch18", "ch19",
+					  "ch20", "ch21", "ch22", "ch23",
+					  "ch24";
+			clocks = <&cpg CPG_MOD 812>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 812>;
+			phy-mode = "rgmii-txid";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		scif2: serial at e6e88000 {
 			compatible = "renesas,scif-r8a77995",
 				     "renesas,rcar-gen3-scif", "renesas,scif";
Signature · 1 line
2.1.4
#11 lore raw

PATCH 11/22 arm64: dts: renesas: initial R8A77970 SoC device tree

In reply to Simon Horman

From: Sergei Shtylyov <[email protected]>

The initial R8A77970 SoC device tree including Cortex-A53 CPU, GIC, timer, CPG, RST, and SYSC.

Based on the original (and large) patch by Daisuke Matsushita <[email protected]>.

---
 arch/arm64/boot/dts/renesas/r8a77970.dtsi | 125 ++++++++++++++++++++++++++++++
 1 file changed, 125 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a77970.dtsi
arch/arm64/boot/dts/renesas/r8a77970.dtsi new file +125 -0
new file mode 100644
index 000000000000..dec3492cd7dc
@@ -0,0 +1,125 @@
+/*
+ * Device Tree Source for the r8a77970 SoC
+ *
+ * Copyright (C) 2016-2017 Renesas Electronics Corp.
+ * Copyright (C) 2017 Cogent Embedded, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/renesas-cpg-mssr.h>
+
+/ {
+	compatible = "renesas,r8a77970";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		a53_0: cpu at 0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53", "arm,armv8";
+			reg = <0>;
+			clocks = <&cpg CPG_CORE 0>;
+			power-domains = <&sysc 5>;
+			next-level-cache = <&L2_CA53>;
+			enable-method = "psci";
+		};
+
+		L2_CA53: cache-controller {
+			compatible = "cache";
+			power-domains = <&sysc 21>;
+			cache-unified;
+			cache-level = <2>;
+		};
+	};
+
+	extal_clk: extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	extalr_clk: extalr {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		gic: interrupt-controller at f1010000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0 0xf1010000 0 0x1000>,
+			      <0 0xf1020000 0 0x20000>,
+			      <0 0xf1040000 0 0x20000>,
+			      <0 0xf1060000 0 0x20000>;
+			interrupts = <GIC_PPI 9	(GIC_CPU_MASK_SIMPLE(1) |
+				      IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&cpg CPG_MOD 408>;
+			clock-names = "clk";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 408>;
+		};
+
+		timer {
+			compatible = "arm,armv8-timer";
+			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
+						  IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) |
+						  IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) |
+						  IRQ_TYPE_LEVEL_LOW)>,
+				     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) |
+						  IRQ_TYPE_LEVEL_LOW)>;
+		};
+
+		cpg: clock-controller at e6150000 {
+			compatible = "renesas,r8a77970-cpg-mssr";
+			reg = <0 0xe6150000 0 0x1000>;
+			clocks = <&extal_clk>, <&extalr_clk>;
+			clock-names = "extal", "extalr";
+			#clock-cells = <2>;
+			#power-domain-cells = <0>;
+			#reset-cells = <1>;
+		};
+
+		rst: reset-controller at e6160000 {
+			compatible = "renesas,r8a77970-rst";
+			reg = <0 0xe6160000 0 0x200>;
+		};
+
+		sysc: system-controller at e6180000 {
+			compatible = "renesas,r8a77970-sysc";
+			reg = <0 0xe6180000 0 0x440>;
+			#power-domain-cells = <1>;
+		};
+
+		prr: chipid at fff00044 {
+			compatible = "renesas,prr";
+			reg = <0 0xfff00044 0 4>;
+		};
+	};
+};
Signature · 1 line
2.1.4
#12 lore raw

PATCH 12/22 arm64: dts: renesas: r8a77970: add SYS-DMAC support

In reply to Simon Horman

From: Sergei Shtylyov <[email protected]>

Describe SYS-DMAC1/2 in the R8A77970 device tree.

Based on the original (and large) patch by Daisuke Matsushita <[email protected]>.

---
 arch/arm64/boot/dts/renesas/r8a77970.dtsi | 48 +++++++++++++++++++++++++++++++
 1 file changed, 48 insertions(+)
arch/arm64/boot/dts/renesas/r8a77970.dtsi +48 -0
index dec3492cd7dc..a2a438a91b3f 100644
@@ -121,5 +121,53 @@
 			compatible = "renesas,prr";
 			reg = <0 0xfff00044 0 4>;
 		};
+
+		dmac1: dma-controller at e7300000 {
+			compatible = "renesas,dmac-r8a77970",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe7300000 0 0x10000>;
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7";
+			clocks = <&cpg CPG_MOD 218>;
+			clock-names = "fck";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 218>;
+			#dma-cells = <1>;
+			dma-channels = <8>;
+		};
+
+		dmac2: dma-controller at e7310000 {
+			compatible = "renesas,dmac-r8a77970",
+				     "renesas,rcar-dmac";
+			reg = <0 0xe7310000 0 0x10000>;
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7";
+			clocks = <&cpg CPG_MOD 217>;
+			clock-names = "fck";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 217>;
+			#dma-cells = <1>;
+			dma-channels = <8>;
+		};
 	};
 };
Signature · 1 line
2.1.4
#13 lore raw

PATCH 13/22 arm64: dts: renesas: r8a77970: add [H]SCIF support

In reply to Simon Horman

From: Sergei Shtylyov <[email protected]>

Describe [H]SCIF ports in the R8A77970 device tree.

Based on the original (and large) patch by Daisuke Matsushita <[email protected]>.

---
 arch/arm64/boot/dts/renesas/r8a77970.dtsi | 149 ++++++++++++++++++++++++++++++
 1 file changed, 149 insertions(+)
arch/arm64/boot/dts/renesas/r8a77970.dtsi +149 -0
index a2a438a91b3f..04ec0e459686 100644
@@ -59,6 +59,13 @@
 		clock-frequency = <0>;
 	};
 
+	/* External SCIF clock - to be overridden by boards that provide it */
+	scif_clk: scif {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
 	soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&gic>;
@@ -169,5 +176,147 @@
 			#dma-cells = <1>;
 			dma-channels = <8>;
 		};
+
+		hscif0: serial at e6540000 {
+			compatible = "renesas,hscif-r8a77970",
+				     "renesas,rcar-gen3-hscif",
+				     "renesas,hscif";
+			reg = <0 0xe6540000 0 96>;
+			interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 520>,
+				 <&cpg CPG_CORE 9>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x31>, <&dmac1 0x30>,
+			       <&dmac2 0x31>, <&dmac2 0x30>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 520>;
+			status = "disabled";
+		};
+
+		hscif1: serial at e6550000 {
+			compatible = "renesas,hscif-r8a77970",
+				     "renesas,rcar-gen3-hscif",
+				     "renesas,hscif";
+			reg = <0 0xe6550000 0 96>;
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 519>,
+				 <&cpg CPG_CORE 9>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x33>, <&dmac1 0x32>,
+			       <&dmac2 0x33>, <&dmac2 0x32>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 519>;
+			status = "disabled";
+		};
+
+		hscif2: serial at e6560000 {
+			compatible = "renesas,hscif-r8a77970",
+				     "renesas,rcar-gen3-hscif",
+				     "renesas,hscif";
+			reg = <0 0xe6560000 0 96>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 518>,
+				 <&cpg CPG_CORE 9>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x35>, <&dmac1 0x34>,
+			       <&dmac2 0x35>, <&dmac2 0x34>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 518>;
+			status = "disabled";
+		};
+
+		hscif3: serial at e66a0000 {
+			compatible = "renesas,hscif-r8a77970",
+				     "renesas,rcar-gen3-hscif", "renesas,hscif";
+			reg = <0 0xe66a0000 0 96>;
+			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 517>,
+				 <&cpg CPG_CORE 9>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x37>, <&dmac1 0x36>,
+			       <&dmac2 0x37>, <&dmac2 0x36>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 517>;
+			status = "disabled";
+		};
+
+		scif0: serial at e6e60000 {
+			compatible = "renesas,scif-r8a77970",
+				     "renesas,rcar-gen3-scif",
+				     "renesas,scif";
+			reg = <0 0xe6e60000 0 64>;
+			interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 207>,
+				 <&cpg CPG_CORE 9>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x51>, <&dmac1 0x50>,
+			       <&dmac2 0x51>, <&dmac2 0x50>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 207>;
+			status = "disabled";
+		};
+
+		scif1: serial at e6e68000 {
+			compatible = "renesas,scif-r8a77970",
+				     "renesas,rcar-gen3-scif",
+				     "renesas,scif";
+			reg = <0 0xe6e68000 0 64>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 206>,
+				 <&cpg CPG_CORE 9>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x53>, <&dmac1 0x52>,
+			       <&dmac2 0x53>, <&dmac2 0x52>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 206>;
+			status = "disabled";
+		};
+
+		scif3: serial at e6c50000 {
+			compatible = "renesas,scif-r8a77970",
+				     "renesas,rcar-gen3-scif",
+				     "renesas,scif";
+			reg = <0 0xe6c50000 0 64>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 204>,
+				 <&cpg CPG_CORE 9>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x57>, <&dmac1 0x56>,
+			       <&dmac2 0x57>, <&dmac2 0x56>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 204>;
+			status = "disabled";
+		};
+
+		scif4: serial at e6c40000 {
+			compatible = "renesas,scif-r8a77970",
+				     "renesas,rcar-gen3-scif", "renesas,scif";
+			reg = <0 0xe6c40000 0 64>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 203>,
+				 <&cpg CPG_CORE 9>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac1 0x59>, <&dmac1 0x58>,
+			       <&dmac2 0x59>, <&dmac2 0x58>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc 32>;
+			resets = <&cpg 203>;
+			status = "disabled";
+		};
 	};
 };
Signature · 1 line
2.1.4
#14 lore raw

PATCH 14/22 arm64: dts: renesas: r8a77970: add EtherAVB support

In reply to Simon Horman

From: Sergei Shtylyov <[email protected]>

Define the generic R8A77970 part of the EtherAVB device node.

Based on the original (and large) patch by Daisuke Matsushita <[email protected]>.

---
 arch/arm64/boot/dts/renesas/r8a77970.dtsi | 44 +++++++++++++++++++++++++++++++
 1 file changed, 44 insertions(+)
arch/arm64/boot/dts/renesas/r8a77970.dtsi +44 -0
index 04ec0e459686..aa9032d34189 100644
@@ -318,5 +318,49 @@
 			resets = <&cpg 203>;
 			status = "disabled";
 		};
+
+		avb: ethernet at e6800000 {
+			compatible = "renesas,etheravb-r8a77970",
+				     "renesas,etheravb-rcar-gen3";
+			reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14", "ch15",
+					  "ch16", "ch17", "ch18", "ch19",
+					  "ch20", "ch21", "ch22", "ch23",
+					  "ch24";
+			clocks = <&cpg CPG_MOD 812>;
+			power-domains = <&sysc 32>;
+			resets = <&cpg 812>;
+			phy-mode = "rgmii-id";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
 	};
 };
Signature · 1 line
2.1.4
#15 lore raw

PATCH 15/22 arm64: dts: draak: Add serial console pins

In reply to Simon Horman

From: Geert Uytterhoeven <[email protected]>

Add pin control for SCIF2.

---
 arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +11 -0
index d144370051d5..19c5462d8b67 100644
@@ -36,7 +36,18 @@
 	clock-frequency = <48000000>;
 };
 
+&pfc {
+	scif2_pins: scif2 {
+		groups = "scif2_data";
+		function = "scif2";
+	};
+
+};
+
 &scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+
 	status = "okay";
 };
 
Signature · 1 line
2.1.4
#16 lore raw

PATCH 16/22 arm64: dts: renesas: r8a77995: Add USB2.0 PHY device node

In reply to Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch adds USB2.0 PHY device node for r8a77995.

---
 arch/arm64/boot/dts/renesas/r8a77995.dtsi | 12 ++++++++++++
 1 file changed, 12 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995.dtsi +12 -0
index 72d04d7337be..59ed1303bd93 100644
@@ -309,5 +309,17 @@
 			resets = <&cpg 310>;
 			status = "disabled";
 		};
+
+		usb2_phy0: usb-phy at ee080200 {
+			compatible = "renesas,usb2-phy-r8a77995",
+				     "renesas,rcar-gen3-usb2-phy";
+			reg = <0 0xee080200 0 0x700>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 703>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 703>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
 	};
 };
Signature · 1 line
2.1.4
#17 lore raw

PATCH 17/22 arm64: dts: renesas: r8a77995: add USB2.0 Host (EHCI/OHCI) device node

In reply to Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch adds USB2.0 Host (EHCI/OHCI) device node for r8a77995.

---
 arch/arm64/boot/dts/renesas/r8a77995.dtsi | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995.dtsi +25 -0
index 59ed1303bd93..56e42921e879 100644
@@ -310,6 +310,31 @@
 			status = "disabled";
 		};
 
+		ehci0: usb at ee080100 {
+			compatible = "generic-ehci";
+			reg = <0 0xee080100 0 0x100>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 703>;
+			phys = <&usb2_phy0>;
+			phy-names = "usb";
+			companion = <&ohci0>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 703>;
+			status = "disabled";
+		};
+
+		ohci0: usb at ee080000 {
+			compatible = "generic-ohci";
+			reg = <0 0xee080000 0 0x100>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 703>;
+			phys = <&usb2_phy0>;
+			phy-names = "usb";
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 703>;
+			status = "disabled";
+		};
+
 		usb2_phy0: usb-phy at ee080200 {
 			compatible = "renesas,usb2-phy-r8a77995",
 				     "renesas,rcar-gen3-usb2-phy";
Signature · 1 line
2.1.4
#18 lore raw

PATCH 18/22 arm64: dts: renesas: r8a77995: draak: enable USB2.0 PHY

In reply to Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch enables USB2.0 PHY for R-Car D3 draak board.

---
 arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +11 -0
index 19c5462d8b67..454658ac6efc 100644
@@ -42,6 +42,10 @@
 		function = "scif2";
 	};
 
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
 };
 
 &scif2 {
@@ -51,6 +55,13 @@
 	status = "okay";
 };
 
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
 &rwdt {
 	timeout-sec = <60>;
 	status = "okay";
Signature · 1 line
2.1.4
#19 lore raw

PATCH 19/22 arm64: dts: renesas: r8a77995: draak: enable USB2.0 Host (EHCI/OHCI)

In reply to Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch enables USB2.0 Host (EHCI/OHCI) for r8a77995.

---
 arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 8 ++++++++
 1 file changed, 8 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +8 -0
index 454658ac6efc..7b776cb7e928 100644
@@ -48,6 +48,14 @@
 	};
 };
 
+&ehci0 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
 &scif2 {
 	pinctrl-0 = <&scif2_pins>;
 	pinctrl-names = "default";
Signature · 1 line
2.1.4
#20 lore raw

PATCH 20/22 arm64: dts: renesas: r8a77995: draak: enable EthernetAVB

In reply to Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch enables EthernetAVB for R-Car D3 draak board.

---
 arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +25 -0
index 7b776cb7e928..96b7ff5cc321 100644
@@ -11,6 +11,7 @@
 
 /dts-v1/;
 #include "r8a77995.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Renesas Draak board based on r8a77995";
@@ -18,6 +19,7 @@
 
 	aliases {
 		serial0 = &scif2;
+		ethernet0 = &avb;
 	};
 
 	chosen {
@@ -37,6 +39,14 @@
 };
 
 &pfc {
+	avb0_pins: avb {
+		mux {
+			groups = "avb0_link", "avb0_phy_int", "avb0_mdc",
+				 "avb0_mii";
+			function = "avb0";
+		};
+	};
+
 	scif2_pins: scif2 {
 		groups = "scif2_data";
 		function = "scif2";
@@ -56,6 +66,21 @@
 	status = "okay";
 };
 
+&avb {
+	pinctrl-0 = <&avb0_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy at 0 {
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
 &scif2 {
 	pinctrl-0 = <&scif2_pins>;
 	pinctrl-names = "default";
Signature · 1 line
2.1.4
#21 lore raw

PATCH 20/22 arm64: dts: renesas: r8a77995: draak: enable EthernetAVB

Hello!

Quoted 15 lines · Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch enables EthernetAVB for R-Car D3 draak board.

---
  arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 25 +++++++++++++++++++++++++
  1 file changed, 25 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +0 -0
index 7b776cb7e928..96b7ff5cc321 100644

[...]

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 44

Quoted 7 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +3 -0
@@ -37,6 +39,14 @@
  };
 
  &pfc {
+	avb0_pins: avb {
+		mux {
+			groups = "avb0_link", "avb0_phy_int", "avb0_mdc",

^^^^^^^^^^^^^^
Hum, I don't think it's compatible with routing the PHY interrupt via
GPIO5_19 below. The driver doesn't support signalling via AVB_PHY_INT anyway.

Quoted 20 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +13 -0
+				 "avb0_mii";
+			function = "avb0";
+		};
+	};
+
  	scif2_pins: scif2 {
  		groups = "scif2_data";
  		function = "scif2";
@@ -56,6 +66,21 @@
  	status = "okay";
  };
 
+&avb {
+	pinctrl-0 = <&avb0_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy at 0 {

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 86

Quoted 10 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +7 -0
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
  &scif2 {
  	pinctrl-0 = <&scif2_pins>;
  	pinctrl-names = "default";

MBR, Sergei

#22 lore raw

PATCH 20/22 arm64: dts: renesas: r8a77995: draak: enable EthernetAVB

Hello,

Quoted 27 lines

-----Original Message-----
From: Sergei Shtylyov
Sent: Saturday, September 30, 2017 7:24 PM

Hello!

Quoted 15 lines · Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch enables EthernetAVB for R-Car D3 draak board.

---
  arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 25 +++++++++++++++++++++++++
  1 file changed, 25 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +0 -0
index 7b776cb7e928..96b7ff5cc321 100644

[...]

Quoted 3 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +0 -0
@@ -37,6 +39,14 @@
  };
 
Quoted 7 lines

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 44

Quoted 4 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +3 -0
  &pfc {
+	avb0_pins: avb {
+		mux {
+			groups = "avb0_link", "avb0_phy_int", "avb0_mdc",

^^^^^^^^^^^^^^
Hum, I don't think it's compatible with routing the PHY interrupt via
GPIO5_19 below. The driver doesn't support signalling via AVB_PHY_INT anyway.

Oops! You're correct. I should drop "avb0_phy_int".

Simon-san, may I send a follow-up patch to fix this?

Best regards,
Yoshihiro Shimoda

Quoted 32 lines
Quoted 20 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +13 -0
+				 "avb0_mii";
+			function = "avb0";
+		};
+	};
+
  	scif2_pins: scif2 {
  		groups = "scif2_data";
  		function = "scif2";
@@ -56,6 +66,21 @@
  	status = "okay";
  };
 
+&avb {
+	pinctrl-0 = <&avb0_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy at 0 {

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 86

Quoted 10 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +7 -0
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
  &scif2 {
  	pinctrl-0 = <&scif2_pins>;
  	pinctrl-names = "default";

MBR, Sergei

#23 lore raw

PATCH 20/22 arm64: dts: renesas: r8a77995: draak: enable EthernetAVB

Quoted 37 lines · Yoshihiro Shimoda

Hello,

Quoted 27 lines

-----Original Message-----
From: Sergei Shtylyov
Sent: Saturday, September 30, 2017 7:24 PM

Hello!

Quoted 15 lines · Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch enables EthernetAVB for R-Car D3 draak board.

---
  arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 25 +++++++++++++++++++++++++
  1 file changed, 25 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +0 -0
index 7b776cb7e928..96b7ff5cc321 100644

[...]

Quoted 3 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +0 -0
@@ -37,6 +39,14 @@
  };
 
Quoted 7 lines

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 44

Quoted 4 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +3 -0
  &pfc {
+	avb0_pins: avb {
+		mux {
+			groups = "avb0_link", "avb0_phy_int", "avb0_mdc",

^^^^^^^^^^^^^^
Hum, I don't think it's compatible with routing the PHY interrupt via
GPIO5_19 below. The driver doesn't support signalling via AVB_PHY_INT anyway.

Quoted 3 lines

Oops! You're correct. I should drop "avb0_phy_int".

Simon-san, may I send a follow-up patch to fix this?

Thanks Sergei, thanks Shimoda-san,

yes, please provide a follow-up patch.

At this stage I don't think we need to re-spin this pull-request to fix this, rather a follow-up patch can be included in a follow-up pull request.

Quoted 36 lines

Best regards,
Yoshihiro Shimoda

Quoted 32 lines
Quoted 20 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +13 -0
+				 "avb0_mii";
+			function = "avb0";
+		};
+	};
+
  	scif2_pins: scif2 {
  		groups = "scif2_data";
  		function = "scif2";
@@ -56,6 +66,21 @@
  	status = "okay";
  };
 
+&avb {
+	pinctrl-0 = <&avb0_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy at 0 {

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 86

Quoted 10 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +7 -0
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
  &scif2 {
  	pinctrl-0 = <&scif2_pins>;
  	pinctrl-names = "default";

MBR, Sergei

#24 lore raw

PATCH 20/22 arm64: dts: renesas: r8a77995: draak: enable EthernetAVB

Hi Simon-san,

Quoted 46 lines

-----Original Message-----
From: Simon Horman
Sent: Monday, October 2, 2017 4:15 PM

Quoted 37 lines · Yoshihiro Shimoda

Hello,

Quoted 27 lines

-----Original Message-----
From: Sergei Shtylyov
Sent: Saturday, September 30, 2017 7:24 PM

Hello!

Quoted 15 lines · Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch enables EthernetAVB for R-Car D3 draak board.

---
  arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 25 +++++++++++++++++++++++++
  1 file changed, 25 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +0 -0
index 7b776cb7e928..96b7ff5cc321 100644

[...]

Quoted 3 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +0 -0
@@ -37,6 +39,14 @@
  };
 
Quoted 7 lines

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 44

Quoted 4 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +3 -0
  &pfc {
+	avb0_pins: avb {
+		mux {
+			groups = "avb0_link", "avb0_phy_int", "avb0_mdc",

^^^^^^^^^^^^^^
Hum, I don't think it's compatible with routing the PHY interrupt via
GPIO5_19 below. The driver doesn't support signalling via AVB_PHY_INT anyway.

Quoted 3 lines

Oops! You're correct. I should drop "avb0_phy_int".

Simon-san, may I send a follow-up patch to fix this?

Quoted 7 lines

Thanks Sergei, thanks Shimoda-san,

yes, please provide a follow-up patch.

At this stage I don't think we need to re-spin this pull-request to fix this, rather a follow-up patch can be included in a follow-up pull request.

I got it. I will send it. Also, should I send salvator-common and ulcb patches about Geert-san's comment (These dtsi files also enable "avb_phy_int" for now)?

Best regards,
Yoshihiro Shimoda

Quoted 36 lines
Quoted 36 lines

Best regards,
Yoshihiro Shimoda

Quoted 32 lines
Quoted 20 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +13 -0
+				 "avb0_mii";
+			function = "avb0";
+		};
+	};
+
  	scif2_pins: scif2 {
  		groups = "scif2_data";
  		function = "scif2";
@@ -56,6 +66,21 @@
  	status = "okay";
  };
 
+&avb {
+	pinctrl-0 = <&avb0_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy at 0 {

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 86

Quoted 10 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +7 -0
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
  &scif2 {
  	pinctrl-0 = <&scif2_pins>;
  	pinctrl-names = "default";

MBR, Sergei

#25 lore raw

PATCH 20/22 arm64: dts: renesas: r8a77995: draak: enable EthernetAVB

Quoted 50 lines · Yoshihiro Shimoda

Hi Simon-san,

Quoted 48 lines

-----Original Message-----
From: Simon Horman
Sent: Monday, October 2, 2017 4:15 PM

Quoted 37 lines · Yoshihiro Shimoda

Hello,

Quoted 27 lines

-----Original Message-----
From: Sergei Shtylyov
Sent: Saturday, September 30, 2017 7:24 PM

Hello!

Quoted 15 lines · Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch enables EthernetAVB for R-Car D3 draak board.

---
  arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 25 +++++++++++++++++++++++++
  1 file changed, 25 insertions(+)
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +0 -0
index 7b776cb7e928..96b7ff5cc321 100644

[...]

Quoted 3 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +0 -0
@@ -37,6 +39,14 @@
  };
 
Quoted 7 lines

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 44

Quoted 4 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +3 -0
  &pfc {
+	avb0_pins: avb {
+		mux {
+			groups = "avb0_link", "avb0_phy_int", "avb0_mdc",

^^^^^^^^^^^^^^
Hum, I don't think it's compatible with routing the PHY interrupt via
GPIO5_19 below. The driver doesn't support signalling via AVB_PHY_INT anyway.

Quoted 3 lines

Oops! You're correct. I should drop "avb0_phy_int".

Simon-san, may I send a follow-up patch to fix this?

Thanks Sergei, thanks Shimoda-san,

Quoted 8 lines
Quoted 5 lines

yes, please provide a follow-up patch.

At this stage I don't think we need to re-spin this pull-request to fix this, rather a follow-up patch can be included in a follow-up pull request.

I got it. I will send it. Also, should I send salvator-common and ulcb patches about Geert-san's comment (These dtsi files also enable "avb_phy_int" for now)?

Hi Shimoda-san,

yes, I think that would be best.

Please include Fixes tags.

#26 lore raw

PATCH 20/22 arm64: dts: renesas: r8a77995: draak: enable EthernetAVB

In reply to Sergei Shtylyov

Hi Sergei,

Quoted 22 lines · Sergei Shtylyov
Quoted 10 lines · Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch enables EthernetAVB for R-Car D3 draak board.

arch/arm64/boot/dts/renesas/r8a77995-draak.dts +0 -0

[...]

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 43

Quoted 7 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +3 -0
@@ -37,6 +39,14 @@
  };
    &pfc {
+       avb0_pins: avb {
+               mux {
+                       groups = "avb0_link", "avb0_phy_int", "avb0_mdc",
                                              ^^^^^^^^^^^^^^
Quoted 3 lines

Hum, I don't think it's compatible with routing the PHY interrupt via
GPIO5_19 below. The driver doesn't support signalling via AVB_PHY_INT anyway.

Seems we have the same issue in arch/arm64/boot/dts/renesas/ulcb.dtsi and arch/arm64/boot/dts/renesas/salvator-common.dtsi?

Quoted 9 lines

arch/arm64/boot/dts/renesas/r8a77995-draak.dts line 82

Quoted 9 lines
arch/arm64/boot/dts/renesas/r8a77995-draak.dts +7 -0
  +&avb {
 
+       phy0: ethernet-phy at 0 {
+               rxc-skew-ps = <1500>;
+               reg = <0>;
+               interrupt-parent = <&gpio5>;
+               interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+       };
+};

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds

#27 lore raw

PATCH 21/22 arm64: dts: renesas: r8a7795: add USB3.0 peripheral device node

In reply to Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch adds USB3.0 peripheral channel 0 device node for r8a7795.

---
 arch/arm64/boot/dts/renesas/r8a7795.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/renesas/r8a7795.dtsi +11 -0
index 5d5174d8635d..d5cfd1a1c539 100644
@@ -1471,6 +1471,17 @@
 			status = "disabled";
 		};
 
+		usb3_peri0: usb at ee020000 {
+			compatible = "renesas,r8a7795-usb3-peri",
+				     "renesas,rcar-gen3-usb3-peri";
+			reg = <0 0xee020000 0 0x400>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 328>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			resets = <&cpg 328>;
+			status = "disabled";
+		};
+
 		usb_dmac0: dma-controller at e65a0000 {
 			compatible = "renesas,r8a7795-usb-dmac",
 				     "renesas,usb-dmac";
Signature · 1 line
2.1.4
#28 lore raw

PATCH 22/22 arm64: dts: renesas: r8a7796: add USB3.0 peripheral device node

In reply to Simon Horman

From: Yoshihiro Shimoda <[email protected]>

This patch adds USB3.0 peripheral channel 0 device node for r8a7796.

---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)
arch/arm64/boot/dts/renesas/r8a7796.dtsi +11 -0
index 16da83458f18..57ac5ca6ed98 100644
@@ -1279,6 +1279,17 @@
 			status = "disabled";
 		};
 
+		usb3_peri0: usb at ee020000 {
+			compatible = "renesas,r8a7796-usb3-peri",
+				     "renesas,rcar-gen3-usb3-peri";
+			reg = <0 0xee020000 0 0x400>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 328>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			resets = <&cpg 328>;
+			status = "disabled";
+		};
+
 		ohci0: usb at ee080000 {
 			compatible = "generic-ohci";
 			reg = <0 0xee080000 0 0x100>;
Signature · 1 line
2.1.4
#29 lore raw
In reply to Simon Horman
Quoted 42 lines · Simon Horman

----------------------------------------------------------------
Renesas ARM64 Based SoC DT Updates for v4.15

* r8a7795 (H3)
- Use r8a7795-cpg-mssr and r8a7795-sysc bindings
Hardcoded indicies are replaced with symbols now that they are available

- Drop bogus HDMI node name suffixes
Laurent Pinchart says: Node names should not use numerical suffixes if the nodes can be distinguished by unit-address

- Update PFC node name to pin-controller
Shimoda-san says the PFC node name is changed "from e6060000.pfc and pfc at e6060000 to e6060000.pin-controller and pin-controller at e6060000 like other Renesas SoCs."

* r8a7795 (H3) ES1.0
- Drop extra zero from XHCI unit address
This corrects a typo were ee0400000 rather than ee040000 was used as the unit address.

* r8a7796 (M3-W)
- Add FDP1 instance
Laurent Pinchart says: The r8a7796 has a single FDP1 instance.

* r8a7795 (H3) and r8a7796 (M3-W) SoCs
- Add USB3.0 peripheral device nodes
Shimoda-san says that this is not enabled on the Salvator-X/XS boards for now as:
+ we need a special cable (USB type-A to A cross cable).
+ we can swap the role by renesas_usb3 driver even if we use a normal cable and after usb3.0 host is running, but I think it's a special use case.

* r8a7795 (H3) and r8a7796 (M3-W) ULCB boards
- Enable display output
Laurent Pinchart says: The DU is already wired up to the HDMI encoder, all we need to do is enable it.

* r8a77995 (D3) Draak board
- Enable EthernetAVB and , USB2.0 Host and PHY

Quoted 7 lines

- Add serial console pins.
This is safe to do now that r8a77995 PFC driver support is present

* r8a77970 (V3M)
- Add basic support for SoC and EtherAVB, [H]SCIF and SYS-DMAC nodes This is a step towards enabling EtherAVB and [H]SCIF with SYS-DMAC in the Eagle board support for which is under review

Thanks for the detailed changelog!

Quoted 5 lines

----------------------------------------------------------------
Geert Uytterhoeven (6):
arm64: dts: renesas: r8a7795-es1: Drop extra zero from usb unit address
arm64: dts: renesas: r8a7795: Drop bogus HDMI node names suffixes
arm64: renesas: Add Renesas R8A77970 Kconfig support

That one last commit doesn't seem to belong in here, but I've pulled it anyway, thanks!

Arnd

#30 lore raw
Quoted 54 lines · Arnd Bergmann
Quoted 42 lines · Simon Horman

----------------------------------------------------------------
Renesas ARM64 Based SoC DT Updates for v4.15

* r8a7795 (H3)
- Use r8a7795-cpg-mssr and r8a7795-sysc bindings
Hardcoded indicies are replaced with symbols now that they are available

- Drop bogus HDMI node name suffixes
Laurent Pinchart says: Node names should not use numerical suffixes if the nodes can be distinguished by unit-address

- Update PFC node name to pin-controller
Shimoda-san says the PFC node name is changed "from e6060000.pfc and pfc at e6060000 to e6060000.pin-controller and pin-controller at e6060000 like other Renesas SoCs."

* r8a7795 (H3) ES1.0
- Drop extra zero from XHCI unit address
This corrects a typo were ee0400000 rather than ee040000 was used as the unit address.

* r8a7796 (M3-W)
- Add FDP1 instance
Laurent Pinchart says: The r8a7796 has a single FDP1 instance.

* r8a7795 (H3) and r8a7796 (M3-W) SoCs
- Add USB3.0 peripheral device nodes
Shimoda-san says that this is not enabled on the Salvator-X/XS boards for now as:
+ we need a special cable (USB type-A to A cross cable).
+ we can swap the role by renesas_usb3 driver even if we use a normal cable and after usb3.0 host is running, but I think it's a special use case.

* r8a7795 (H3) and r8a7796 (M3-W) ULCB boards
- Enable display output
Laurent Pinchart says: The DU is already wired up to the HDMI encoder, all we need to do is enable it.

* r8a77995 (D3) Draak board
- Enable EthernetAVB and , USB2.0 Host and PHY

Quoted 7 lines

- Add serial console pins.
This is safe to do now that r8a77995 PFC driver support is present

* r8a77970 (V3M)
- Add basic support for SoC and EtherAVB, [H]SCIF and SYS-DMAC nodes This is a step towards enabling EtherAVB and [H]SCIF with SYS-DMAC in the Eagle board support for which is under review

Thanks for the detailed changelog!

Quoted 8 lines
Quoted 5 lines

----------------------------------------------------------------
Geert Uytterhoeven (6):
arm64: dts: renesas: r8a7795-es1: Drop extra zero from usb unit address
arm64: dts: renesas: r8a7795: Drop bogus HDMI node names suffixes
arm64: renesas: Add Renesas R8A77970 Kconfig support

That one last commit doesn't seem to belong in here, but I've pulled it anyway, thanks!

Thanks! I take it you would have prefered this in an soc branch?

#31 lore raw
Quoted 7 lines · Simon Horman
Quoted 4 lines · Arnd Bergmann

On Fri, Sep 29, 2017 at 1:52 PM, Simon Horman

That one last commit doesn't seem to belong in here, but I've pulled it anyway, thanks!

Thanks! I take it you would have prefered this in an soc branch?

Yes, correct.

Arnd

#32 lore raw
Quoted 10 lines · Arnd Bergmann
Quoted 7 lines · Simon Horman
Quoted 4 lines · Arnd Bergmann

On Fri, Sep 29, 2017 at 1:52 PM, Simon Horman

That one last commit doesn't seem to belong in here, but I've pulled it anyway, thanks!

Thanks! I take it you would have prefered this in an soc branch?

Yes, correct.

Understood and noted for next time.