misc serdev: new serdev based driver for Wi2Wi w2sg00x4 GPS module

Add driver for Wi2Wi W2SG0004/84 GPS module connected through uart.

Use serdev API hooks to monitor and forward the UART traffic to /dev/ttyGPSn and turn on/off the module. It also detects if the module is turned on (sends data) but should be off, e.g. if it was already turned on during boot or power-on-reset.

Additionally, rfkill block/unblock can be used to control an external LNA (and power down the module if not needed).

The driver concept is based on code developed by NeilBrown <[email protected]> but simplified and adapted to use the new serdev API introduced in 4.11.

Signed-off-by H. Nikolaus Schaller <[email protected]>

---
 drivers/misc/Kconfig    |  10 +
 drivers/misc/Makefile   |   1 +
 drivers/misc/w2sg0004.c | 545 ++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 556 insertions(+)
 create mode 100644 drivers/misc/w2sg0004.c

drivers/misc/Kconfig +10 -0

index 8136dc7e863d..09d171d68408 100644
@@ -518,4 +518,14 @@ source "drivers/misc/mic/Kconfig"
 source "drivers/misc/genwqe/Kconfig"
 source "drivers/misc/echo/Kconfig"
 source "drivers/misc/cxl/Kconfig"
+
+config W2SG0004
+	tristate "W2SG00x4 on/off control"
+	depends on GPIOLIB && SERIAL_DEV_BUS
+	help
+          Enable on/off control of W2SG00x4 GPS moduled connected
+	  to some SoC UART to allow powering up/down if the /dev/ttyGPSn
+	  is opened/closed.
+	  It also provides a rfkill gps name to control the LNA power.
+
 endmenu

drivers/misc/Makefile +1 -0

index ad0e64fdba34..abcb667e0ff0 100644
@@ -51,6 +51,7 @@ obj-$(CONFIG_SRAM_EXEC)		+= sram-exec.o
 obj-y				+= mic/
 obj-$(CONFIG_GENWQE)		+= genwqe/
 obj-$(CONFIG_ECHO)		+= echo/
+obj-$(CONFIG_W2SG0004)		+= w2sg0004.o
 obj-$(CONFIG_VEXPRESS_SYSCFG)	+= vexpress-syscfg.o
 obj-$(CONFIG_CXL_BASE)		+= cxl/
 obj-$(CONFIG_ASPEED_LPC_CTRL)	+= aspeed-lpc-ctrl.o

drivers/misc/w2sg0004.c new file +0 -0

new file mode 100644
index 000000000000..12e14b5e0a99

drivers/misc/w2sg0004.c new file +67 -0

+ * This receiver has an ON/OFF pin which must be toggled to
+ * turn the device 'on' of 'off'.  A high->low->high toggle
+ * will switch the device on if it is off, and off if it is on.
+ *
+ * To enable receiving on/off requests we register with the
+ * UART power management notifications.
+ *
+ * It is not possible to directly detect the state of the device.
+ * However when it is on it will send characters on a UART line
+ * regularly.
+ *
+ * To detect that the power state is out of sync (e.g. if GPS
+ * was enabled before a reboot), we register for UART data received
+ * notifications.
+ *
+ * In addition we register as a rfkill client so that we can
+ * control the LNA power.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/rfkill.h>
+#include <linux/serdev.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/workqueue.h>
+
+/*
+ * There seems to be restrictions on how quickly we can toggle the
+ * on/off line.  data sheets says "two rtc ticks", whatever that means.
+ * If we do it too soon it doesn't work.
+ * So we have a state machine which uses the common work queue to ensure
+ * clean transitions.
+ * When a change is requested we record that request and only act on it
+ * once the previous change has completed.
+ * A change involves a 10ms low pulse, and a 990ms raised level, so only
+ * one change per second.
+ */
+
+enum w2sg_state {
+	W2SG_IDLE,	/* is not changing state */
+	W2SG_PULSE,	/* activate on/off impulse */
+	W2SG_NOPULSE	/* deactivate on/off impulse */
+};
+
+struct w2sg_data {
+	struct		rfkill *rf_kill;
+	struct		regulator *lna_regulator;
+	int		lna_blocked;	/* rfkill block gps active */
+	int		lna_is_off;	/* LNA is currently off */
+	int		is_on;		/* current state (0/1) */
+	unsigned long	last_toggle;
+	unsigned long	backoff;	/* time to wait since last_toggle */
+	int		on_off_gpio;	/* the on-off gpio number */
+	struct		serdev_device *uart;	/* uart connected to the chip */
+	struct		tty_driver *tty_drv;	/* this is the user space tty */

drivers/misc/w2sg0004.c new file +80 -0

+static int w2sg_set_lna_power(struct w2sg_data *data)
+{
+	int ret = 0;
+	int off = data->suspended || !data->requested || data->lna_blocked;
+
+	pr_debug("%s: %s\n", __func__, off ? "off" : "on");
+
+	if (off != data->lna_is_off) {
+		data->lna_is_off = off;
+		if (!IS_ERR_OR_NULL(data->lna_regulator)) {
+			if (off)
+				regulator_disable(data->lna_regulator);
+			else
+				ret = regulator_enable(data->lna_regulator);
+		}
+	}
+
+	return ret;
+}
+
+static void w2sg_set_power(void *pdata, int val)
+{
+	struct w2sg_data *data = (struct w2sg_data *) pdata;
+
+	pr_debug("%s to state=%d (requested=%d)\n", __func__, val, data->requested);
+
+	if (val && !data->requested) {
+		data->requested = true;
+	} else if (!val && data->requested) {
+		data->backoff = HZ;
+		data->requested = false;
+	} else
+		return;
+
+	pr_debug("w2sg00x4 scheduled for %d\n", data->requested);
+
+	if (!data->suspended)
+		schedule_delayed_work(&data->work, 0);
+}
+
+/* called each time data is received by the UART (i.e. sent by the w2sg0004) */
+
+static int w2sg_uart_receive_buf(struct serdev_device *serdev,
+				const unsigned char *rxdata,
+				size_t count)
+{
+	struct w2sg_data *data =
+		(struct w2sg_data *) serdev_device_get_drvdata(serdev);
+
+	if (!data->requested && !data->is_on) {
+		/*
+		 * we have received characters while the w2sg
+		 * should have been be turned off
+		 */
+		data->discard_count += count;
+		if ((data->state == W2SG_IDLE) &&
+		    time_after(jiffies,
+		    data->last_toggle + data->backoff)) {
+			/* Should be off by now, time to toggle again */
+			pr_debug("w2sg00x4 has sent %d characters data although it should be off!\n",
+				data->discard_count);
+
+			data->discard_count = 0;
+
+			data->is_on = true;
+			data->backoff *= 2;
+			if (!data->suspended)
+				schedule_delayed_work(&data->work, 0);
+		}
+	} else if (data->open_count > 0) {
+		int n;
+
+		pr_debug("w2sg00x4: push %lu chars to tty port\n",
+			(unsigned long) count);
+
+		/* pass to user-space */
+		n = tty_insert_flip_string(&data->port, rxdata, count);
+		if (n != count)
+			pr_err("w2sg00x4: did loose %lu characters\n",
+				(unsigned long) (count - n));

drivers/misc/w2sg0004.c new file +129 -0

+static void toggle_work(struct work_struct *work)
+{
+	struct w2sg_data *data = container_of(work, struct w2sg_data,
+					      work.work);
+
+	switch (data->state) {
+	case W2SG_IDLE:
+		if (data->requested == data->is_on)
+			return;
+
+		w2sg_set_lna_power(data);	/* update LNA power state */
+		gpio_set_value_cansleep(data->on_off_gpio, 0);
+		data->state = W2SG_PULSE;
+
+		pr_debug("w2sg: power gpio ON\n");
+
+		schedule_delayed_work(&data->work,
+				      msecs_to_jiffies(10));
+		break;
+
+	case W2SG_PULSE:
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->last_toggle = jiffies;
+		data->state = W2SG_NOPULSE;
+		data->is_on = !data->is_on;
+
+		pr_debug("w2sg: power gpio OFF\n");
+
+		schedule_delayed_work(&data->work,
+				      msecs_to_jiffies(10));
+		break;
+
+	case W2SG_NOPULSE:
+		data->state = W2SG_IDLE;
+
+		pr_debug("w2sg: idle\n");
+
+		break;
+
+	}
+}
+
+static int w2sg_rfkill_set_block(void *pdata, bool blocked)
+{
+	struct w2sg_data *data = pdata;
+
+	pr_debug("%s: blocked: %d\n", __func__, blocked);
+
+	data->lna_blocked = blocked;
+
+	return w2sg_set_lna_power(data);
+}
+
+static struct rfkill_ops w2sg0004_rfkill_ops = {
+	.set_block = w2sg_rfkill_set_block,
+};
+
+static struct serdev_device_ops serdev_ops = {
+	.receive_buf = w2sg_uart_receive_buf,
+};
+
+/*
+ * we are a man-in the middle between the user-space visible tty port
+ * and the serdev tty where the chip is connected.
+ * This allows us to recognise when the device should be powered on
+ * or off and handle the "false" state that data arrives while no
+ * users-space tty client exists.
+ */
+
+static struct w2sg_data *w2sg_get_by_minor(unsigned int minor)
+{
+	return w2sg_by_minor[minor];
+}
+
+static int w2sg_tty_install(struct tty_driver *driver, struct tty_struct *tty)
+{
+	struct w2sg_data *data;
+	int retval;
+
+	pr_debug("%s() tty = %p\n", __func__, tty);
+
+	data = w2sg_get_by_minor(tty->index);
+
+	if (!data)
+		return -ENODEV;
+
+	retval = tty_standard_install(driver, tty);
+	if (retval)
+		goto error_init_termios;
+
+	tty->driver_data = data;
+
+	return 0;
+
+error_init_termios:
+	tty_port_put(&data->port);
+	return retval;
+}
+
+static int w2sg_tty_open(struct tty_struct *tty, struct file *file)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	pr_debug("%s() data = %p open_count = ++%d\n", __func__, data, data->open_count);
+
+	w2sg_set_power(data, ++data->open_count > 0);
+
+	return tty_port_open(&data->port, tty, file);
+}
+
+static void w2sg_tty_close(struct tty_struct *tty, struct file *file)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	pr_debug("%s()\n", __func__);
+
+	w2sg_set_power(data, --data->open_count > 0);
+
+	tty_port_close(&data->port, tty, file);
+}
+
+static int w2sg_tty_write(struct tty_struct *tty,
+		const unsigned char *buffer, int count)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	/* simply pass down to UART */
+	return serdev_device_write_buf(data->uart, buffer, count);
+}

drivers/misc/w2sg0004.c new file +147 -0

+
+static int w2sg_probe(struct serdev_device *serdev)
+{
+	struct w2sg_data *data;
+	struct rfkill *rf_kill;
+	int err;
+	int minor;
+	enum of_gpio_flags flags;
+
+	pr_debug("%s()\n", __func__);
+
+	minor = 0;
+	if (w2sg_by_minor[minor]) {
+		pr_err("w2sg minor is already in use!\n");
+		return -ENODEV;
+	}
+
+	data = devm_kzalloc(&serdev->dev, sizeof(*data), GFP_KERNEL);
+	if (data == NULL)
+		return -ENOMEM;
+
+	w2sg_by_minor[minor] = data;
+
+	serdev_device_set_drvdata(serdev, data);
+
+	data->on_off_gpio = of_get_named_gpio_flags(serdev->dev.of_node,
+						     "enable-gpios", 0,
+						     &flags);
+	/* defer until we have all gpios */
+	if (data->on_off_gpio == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	data->lna_regulator = devm_regulator_get_optional(&serdev->dev,
+							"lna");
+	if (IS_ERR(data->lna_regulator)) {
+		/* defer until we can get the regulator */
+		if (PTR_ERR(data->lna_regulator) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
+		data->lna_regulator = NULL;
+	}
+	pr_debug("%s() lna_regulator = %p\n", __func__, data->lna_regulator);
+
+	data->lna_blocked = true;
+	data->lna_is_off = true;
+
+	data->is_on = false;
+	data->requested = false;
+	data->state = W2SG_IDLE;
+	data->last_toggle = jiffies;
+	data->backoff = HZ;
+
+	data->uart = serdev;
+
+	INIT_DELAYED_WORK(&data->work, toggle_work);
+
+	err = devm_gpio_request(&serdev->dev, data->on_off_gpio,
+				"w2sg0004-on-off");
+	if (err < 0)
+		goto out;
+
+	gpio_direction_output(data->on_off_gpio, false);
+
+	serdev_device_set_client_ops(data->uart, &serdev_ops);
+	serdev_device_open(data->uart);
+
+	serdev_device_set_baudrate(data->uart, 9600);
+	serdev_device_set_flow_control(data->uart, false);
+
+	rf_kill = rfkill_alloc("GPS", &serdev->dev, RFKILL_TYPE_GPS,
+				&w2sg0004_rfkill_ops, data);
+	if (rf_kill == NULL) {
+		err = -ENOMEM;
+		goto err_rfkill;
+	}
+
+	err = rfkill_register(rf_kill);
+	if (err) {
+		dev_err(&serdev->dev, "Cannot register rfkill device\n");
+		goto err_rfkill;
+	}
+
+	data->rf_kill = rf_kill;
+
+	/* allocate the tty driver */
+	data->tty_drv = alloc_tty_driver(1);
+	if (!data->tty_drv)
+		return -ENOMEM;
+
+	/* initialize the tty driver */
+	data->tty_drv->owner = THIS_MODULE;
+	data->tty_drv->driver_name = "w2sg0004";
+	data->tty_drv->name = "ttyGPS";
+	data->tty_drv->major = 0;
+	data->tty_drv->minor_start = 0;
+	data->tty_drv->type = TTY_DRIVER_TYPE_SERIAL;
+	data->tty_drv->subtype = SERIAL_TYPE_NORMAL;
+	data->tty_drv->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+	data->tty_drv->init_termios = tty_std_termios;
+	data->tty_drv->init_termios.c_cflag = B9600 | CS8 | CREAD |
+					      HUPCL | CLOCAL;
+	/*
+	 * optional:
+	 * tty_termios_encode_baud_rate(&data->tty_drv->init_termios,
+					115200, 115200);
+	 * w2sg_tty_termios(&data->tty_drv->init_termios);
+	 */
+	tty_set_operations(data->tty_drv, &w2sg_serial_ops);
+
+	/* register the tty driver */
+	err = tty_register_driver(data->tty_drv);
+	if (err) {
+		pr_err("%s - tty_register_driver failed(%d)\n",
+			__func__, err);
+		put_tty_driver(data->tty_drv);
+		goto err_rfkill;
+	}
+
+	tty_port_init(&data->port);
+	data->port.ops = &w2sg_port_ops;
+
+	pr_debug("w2sg call tty_port_register_device\n");
+
+	data->dev = tty_port_register_device(&data->port,
+			data->tty_drv, minor, &serdev->dev);
+
+	pr_debug("w2sg probed\n");
+
+	/* keep off until user space requests the device */
+	w2sg_set_power(data, false);
+
+	return 0;
+
+err_rfkill:
+	rfkill_destroy(rf_kill);
+	serdev_device_close(data->uart);
+out:
+	return err;
+}
+
+static void w2sg_remove(struct serdev_device *serdev)
+{
+	struct w2sg_data *data = serdev_device_get_drvdata(serdev);
+	int minor;
+
+	cancel_delayed_work_sync(&data->work);
+

drivers/misc/w2sg0004.c new file +62 -0

+{
+	struct w2sg_data *data = dev_get_drvdata(dev);
+
+	data->suspended = true;
+
+	cancel_delayed_work_sync(&data->work);
+
+	w2sg_set_lna_power(data);	/* shuts down if needed */
+
+	if (data->state == W2SG_PULSE) {
+		msleep(10);
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->last_toggle = jiffies;
+		data->is_on = !data->is_on;
+		data->state = W2SG_NOPULSE;
+	}
+
+	if (data->state == W2SG_NOPULSE) {
+		msleep(10);
+		data->state = W2SG_IDLE;
+	}
+
+	if (data->is_on) {
+		pr_info("GPS off for suspend %d %d %d\n", data->requested,
+			data->is_on, data->lna_is_off);
+
+		gpio_set_value_cansleep(data->on_off_gpio, 0);
+		msleep(10);
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->is_on = 0;
+	}
+
+	return 0;
+}
+
+static int w2sg_resume(struct device *dev)
+{
+	struct w2sg_data *data = dev_get_drvdata(dev);
+
+	data->suspended = false;
+
+	pr_info("GPS resuming %d %d %d\n", data->requested,
+		data->is_on, data->lna_is_off);
+
+	schedule_delayed_work(&data->work, 0);	/* enables LNA if needed */
+
+	return 0;
+}
+
+static const struct of_device_id w2sg0004_of_match[] = {
+	{ .compatible = "wi2wi,w2sg0004" },
+	{ .compatible = "wi2wi,w2sg0084" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, w2sg0004_of_match);
+
+SIMPLE_DEV_PM_OPS(w2sg_pm_ops, w2sg_suspend, w2sg_resume);
+
+static struct serdev_device_driver w2sg_driver = {
+	.probe		= w2sg_probe,
+	.remove		= w2sg_remove,
+	.driver = {

drivers/misc/w2sg0004.c new file +2 -0

+MODULE_DESCRIPTION("w2sg0004 GPS power management driver");
+MODULE_LICENSE("GPL v2");

Am 23.11.2017 um 17:06 schrieb Andrew F. Davis <[email protected]>:

Quoted 17 lines · H. Nikolaus Schaller

Add driver for Wi2Wi W2SG0004/84 GPS module connected through uart.

Use serdev API hooks to monitor and forward the UART traffic to /dev/ttyGPSn and turn on/off the module. It also detects if the module is turned on (sends data) but should be off, e.g. if it was already turned on during boot or power-on-reset.

Additionally, rfkill block/unblock can be used to control an external LNA (and power down the module if not needed).

The driver concept is based on code developed by NeilBrown <[email protected]> but simplified and adapted to use the new serdev API introduced in 4.11.

Signed-off-by H. Nikolaus Schaller <[email protected]>

---

drivers/misc/Kconfig    |  10 +
drivers/misc/Makefile   |   1 +
drivers/misc/w2sg0004.c | 545 ++++++++++++++++++++++++++++++++++++++++++++++++

Quoted 35 lines

3 files changed, 556 insertions(+)

create mode 100644 drivers/misc/w2sg0004.c

drivers/misc/Kconfig +0 -0

index 8136dc7e863d..09d171d68408 100644
@@ -518,4 +518,14 @@ source "drivers/misc/mic/Kconfig"

source "drivers/misc/genwqe/Kconfig"
source "drivers/misc/echo/Kconfig"
source "drivers/misc/cxl/Kconfig"

drivers/misc/Kconfig +10 -0

+
+config W2SG0004
+	tristate "W2SG00x4 on/off control"
+	depends on GPIOLIB && SERIAL_DEV_BUS
+	help
+          Enable on/off control of W2SG00x4 GPS moduled connected
+	  to some SoC UART to allow powering up/down if the /dev/ttyGPSn
+	  is opened/closed.
+	  It also provides a rfkill gps name to control the LNA power.
+

endmenu

drivers/misc/Makefile +0 -0

index ad0e64fdba34..abcb667e0ff0 100644
@@ -51,6 +51,7 @@ obj-$(CONFIG_SRAM_EXEC)		+= sram-exec.o

obj-y += mic/
obj-$(CONFIG_GENWQE) += genwqe/
obj-$(CONFIG_ECHO) += echo/
+obj-$(CONFIG_W2SG0004) += w2sg0004.o
obj-$(CONFIG_VEXPRESS_SYSCFG) += vexpress-syscfg.o
obj-$(CONFIG_CXL_BASE) += cxl/
obj-$(CONFIG_ASPEED_LPC_CTRL) += aspeed-lpc-ctrl.o

drivers/misc/w2sg0004.c +0 -0

drivers/misc/w2sg0004.c line 1

Quoted 6 lines

new file mode 100644
index 000000000000..12e14b5e0a99

drivers/misc/w2sg0004.c new file +1 -0

@@ -0,0 +1,545 @@
+// SPDX-License-Identifier: GPL-2.0

Damn this looks ugly, oh well :/

drivers/misc/w2sg0004.c line 4

Quoted 4 lines

drivers/misc/w2sg0004.c new file +3 -0

+/*
+ * Driver for power controlling the w2sg0004/w2sg0084 GPS receiver.
+ *

Think you still need copyright tag here somewhere.

drivers/misc/w2sg0004.c line 545

Quoted 3 lines

drivers/misc/w2sg0004.c new file +3 -0

+MODULE_AUTHOR("NeilBrown <[email protected]>");
+MODULE_DESCRIPTION("w2sg0004 GPS power management driver");
+MODULE_LICENSE("GPL v2");

Quoted 72 lines

drivers/misc/w2sg0004.c new file +71 -0

+ * This receiver has an ON/OFF pin which must be toggled to
+ * turn the device 'on' of 'off'.  A high->low->high toggle
+ * will switch the device on if it is off, and off if it is on.
+ *
+ * To enable receiving on/off requests we register with the
+ * UART power management notifications.
+ *
+ * It is not possible to directly detect the state of the device.
+ * However when it is on it will send characters on a UART line
+ * regularly.
+ *
+ * To detect that the power state is out of sync (e.g. if GPS
+ * was enabled before a reboot), we register for UART data received
+ * notifications.
+ *
+ * In addition we register as a rfkill client so that we can
+ * control the LNA power.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/rfkill.h>
+#include <linux/serdev.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/workqueue.h>
+
+/*
+ * There seems to be restrictions on how quickly we can toggle the
+ * on/off line.  data sheets says "two rtc ticks", whatever that means.
+ * If we do it too soon it doesn't work.
+ * So we have a state machine which uses the common work queue to ensure
+ * clean transitions.
+ * When a change is requested we record that request and only act on it
+ * once the previous change has completed.
+ * A change involves a 10ms low pulse, and a 990ms raised level, so only
+ * one change per second.
+ */
+
+enum w2sg_state {
+	W2SG_IDLE,	/* is not changing state */
+	W2SG_PULSE,	/* activate on/off impulse */
+	W2SG_NOPULSE	/* deactivate on/off impulse */
+};
+
+struct w2sg_data {
+	struct		rfkill *rf_kill;
+	struct		regulator *lna_regulator;
+	int		lna_blocked;	/* rfkill block gps active */
+	int		lna_is_off;	/* LNA is currently off */
+	int		is_on;		/* current state (0/1) */
+	unsigned long	last_toggle;
+	unsigned long	backoff;	/* time to wait since last_toggle */
+	int		on_off_gpio;	/* the on-off gpio number */
+	struct		serdev_device *uart;	/* uart connected to the chip */
+	struct		tty_driver *tty_drv;	/* this is the user space tty */
+	struct		device *dev;	/* from tty_port_register_device() */
+	struct		tty_port port;
+	int		open_count;	/* how often we were opened */
+	enum		w2sg_state state;

drivers/misc/w2sg0004.c line 81

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	int		requested;	/* requested state (0/1) */
+	int		suspended;
+	struct delayed_work work;
+	int		discard_count;
+};
+

Kernel doc style.

drivers/misc/w2sg0004.c line 86

Quoted 3 lines

drivers/misc/w2sg0004.c new file +2 -0

+static struct w2sg_data *w2sg_by_minor[1];
+

If you can only have one right now then just drop the array.

Quoted 85 lines

drivers/misc/w2sg0004.c new file +84 -0

+static int w2sg_set_lna_power(struct w2sg_data *data)
+{
+	int ret = 0;
+	int off = data->suspended || !data->requested || data->lna_blocked;
+
+	pr_debug("%s: %s\n", __func__, off ? "off" : "on");
+
+	if (off != data->lna_is_off) {
+		data->lna_is_off = off;
+		if (!IS_ERR_OR_NULL(data->lna_regulator)) {
+			if (off)
+				regulator_disable(data->lna_regulator);
+			else
+				ret = regulator_enable(data->lna_regulator);
+		}
+	}
+
+	return ret;
+}
+
+static void w2sg_set_power(void *pdata, int val)
+{
+	struct w2sg_data *data = (struct w2sg_data *) pdata;
+
+	pr_debug("%s to state=%d (requested=%d)\n", __func__, val, data->requested);
+
+	if (val && !data->requested) {
+		data->requested = true;
+	} else if (!val && data->requested) {
+		data->backoff = HZ;
+		data->requested = false;
+	} else
+		return;
+
+	pr_debug("w2sg00x4 scheduled for %d\n", data->requested);
+
+	if (!data->suspended)
+		schedule_delayed_work(&data->work, 0);
+}
+
+/* called each time data is received by the UART (i.e. sent by the w2sg0004) */
+
+static int w2sg_uart_receive_buf(struct serdev_device *serdev,
+				const unsigned char *rxdata,
+				size_t count)
+{
+	struct w2sg_data *data =
+		(struct w2sg_data *) serdev_device_get_drvdata(serdev);
+
+	if (!data->requested && !data->is_on) {
+		/*
+		 * we have received characters while the w2sg
+		 * should have been be turned off
+		 */
+		data->discard_count += count;
+		if ((data->state == W2SG_IDLE) &&
+		    time_after(jiffies,
+		    data->last_toggle + data->backoff)) {
+			/* Should be off by now, time to toggle again */
+			pr_debug("w2sg00x4 has sent %d characters data although it should be off!\n",
+				data->discard_count);
+
+			data->discard_count = 0;
+
+			data->is_on = true;
+			data->backoff *= 2;
+			if (!data->suspended)
+				schedule_delayed_work(&data->work, 0);
+		}
+	} else if (data->open_count > 0) {
+		int n;
+
+		pr_debug("w2sg00x4: push %lu chars to tty port\n",
+			(unsigned long) count);
+
+		/* pass to user-space */
+		n = tty_insert_flip_string(&data->port, rxdata, count);
+		if (n != count)
+			pr_err("w2sg00x4: did loose %lu characters\n",
+				(unsigned long) (count - n));
+		tty_flip_buffer_push(&data->port);
+		return n;
+	}
+

drivers/misc/w2sg0004.c line 173

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	/* assume we have processed everything */
+	return count;
+}
+
+/* try to toggle the power state by sending a pulse to the on-off GPIO */
+

drop extra line, same everywhere

Quoted 134 lines

drivers/misc/w2sg0004.c new file +133 -0

+static void toggle_work(struct work_struct *work)
+{
+	struct w2sg_data *data = container_of(work, struct w2sg_data,
+					      work.work);
+
+	switch (data->state) {
+	case W2SG_IDLE:
+		if (data->requested == data->is_on)
+			return;
+
+		w2sg_set_lna_power(data);	/* update LNA power state */
+		gpio_set_value_cansleep(data->on_off_gpio, 0);
+		data->state = W2SG_PULSE;
+
+		pr_debug("w2sg: power gpio ON\n");
+
+		schedule_delayed_work(&data->work,
+				      msecs_to_jiffies(10));
+		break;
+
+	case W2SG_PULSE:
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->last_toggle = jiffies;
+		data->state = W2SG_NOPULSE;
+		data->is_on = !data->is_on;
+
+		pr_debug("w2sg: power gpio OFF\n");
+
+		schedule_delayed_work(&data->work,
+				      msecs_to_jiffies(10));
+		break;
+
+	case W2SG_NOPULSE:
+		data->state = W2SG_IDLE;
+
+		pr_debug("w2sg: idle\n");
+
+		break;
+
+	}
+}
+
+static int w2sg_rfkill_set_block(void *pdata, bool blocked)
+{
+	struct w2sg_data *data = pdata;
+
+	pr_debug("%s: blocked: %d\n", __func__, blocked);
+
+	data->lna_blocked = blocked;
+
+	return w2sg_set_lna_power(data);
+}
+
+static struct rfkill_ops w2sg0004_rfkill_ops = {
+	.set_block = w2sg_rfkill_set_block,
+};
+
+static struct serdev_device_ops serdev_ops = {
+	.receive_buf = w2sg_uart_receive_buf,
+};
+
+/*
+ * we are a man-in the middle between the user-space visible tty port
+ * and the serdev tty where the chip is connected.
+ * This allows us to recognise when the device should be powered on
+ * or off and handle the "false" state that data arrives while no
+ * users-space tty client exists.
+ */
+
+static struct w2sg_data *w2sg_get_by_minor(unsigned int minor)
+{
+	return w2sg_by_minor[minor];
+}
+
+static int w2sg_tty_install(struct tty_driver *driver, struct tty_struct *tty)
+{
+	struct w2sg_data *data;
+	int retval;
+
+	pr_debug("%s() tty = %p\n", __func__, tty);
+
+	data = w2sg_get_by_minor(tty->index);
+
+	if (!data)
+		return -ENODEV;
+
+	retval = tty_standard_install(driver, tty);
+	if (retval)
+		goto error_init_termios;
+
+	tty->driver_data = data;
+
+	return 0;
+
+error_init_termios:
+	tty_port_put(&data->port);
+	return retval;
+}
+
+static int w2sg_tty_open(struct tty_struct *tty, struct file *file)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	pr_debug("%s() data = %p open_count = ++%d\n", __func__, data, data->open_count);
+
+	w2sg_set_power(data, ++data->open_count > 0);
+
+	return tty_port_open(&data->port, tty, file);
+}
+
+static void w2sg_tty_close(struct tty_struct *tty, struct file *file)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	pr_debug("%s()\n", __func__);
+
+	w2sg_set_power(data, --data->open_count > 0);
+
+	tty_port_close(&data->port, tty, file);
+}
+
+static int w2sg_tty_write(struct tty_struct *tty,
+		const unsigned char *buffer, int count)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	/* simply pass down to UART */
+	return serdev_device_write_buf(data->uart, buffer, count);
+}
+
+static const struct tty_operations w2sg_serial_ops = {
+	.install = w2sg_tty_install,
+	.open = w2sg_tty_open,

drivers/misc/w2sg0004.c line 312

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	.close = w2sg_tty_close,
+	.write = w2sg_tty_write,
+};
+
+static const struct tty_port_operations w2sg_port_ops = {
+};

drop the brackets? or use NULL below, not sure if this needs memory.

Quoted 15 lines

drivers/misc/w2sg0004.c new file +14 -0

+
+static int w2sg_probe(struct serdev_device *serdev)
+{
+	struct w2sg_data *data;
+	struct rfkill *rf_kill;
+	int err;
+	int minor;
+	enum of_gpio_flags flags;
+
+	pr_debug("%s()\n", __func__);
+
+	minor = 0;
+	if (w2sg_by_minor[minor]) {
+		pr_err("w2sg minor is already in use!\n");

drivers/misc/w2sg0004.c line 334

Quoted 8 lines

drivers/misc/w2sg0004.c new file +8 -0

+		return -ENODEV;
+	}
+
+	data = devm_kzalloc(&serdev->dev, sizeof(*data), GFP_KERNEL);
+	if (data == NULL)
+		return -ENOMEM;
+
+	w2sg_by_minor[minor] = data;

Quoted 90 lines

drivers/misc/w2sg0004.c new file +90 -0

+
+	serdev_device_set_drvdata(serdev, data);
+
+	data->on_off_gpio = of_get_named_gpio_flags(serdev->dev.of_node,
+						     "enable-gpios", 0,
+						     &flags);
+	/* defer until we have all gpios */
+	if (data->on_off_gpio == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	data->lna_regulator = devm_regulator_get_optional(&serdev->dev,
+							"lna");
+	if (IS_ERR(data->lna_regulator)) {
+		/* defer until we can get the regulator */
+		if (PTR_ERR(data->lna_regulator) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
+		data->lna_regulator = NULL;
+	}
+	pr_debug("%s() lna_regulator = %p\n", __func__, data->lna_regulator);
+
+	data->lna_blocked = true;
+	data->lna_is_off = true;
+
+	data->is_on = false;
+	data->requested = false;
+	data->state = W2SG_IDLE;
+	data->last_toggle = jiffies;
+	data->backoff = HZ;
+
+	data->uart = serdev;
+
+	INIT_DELAYED_WORK(&data->work, toggle_work);
+
+	err = devm_gpio_request(&serdev->dev, data->on_off_gpio,
+				"w2sg0004-on-off");
+	if (err < 0)
+		goto out;
+
+	gpio_direction_output(data->on_off_gpio, false);
+
+	serdev_device_set_client_ops(data->uart, &serdev_ops);
+	serdev_device_open(data->uart);
+
+	serdev_device_set_baudrate(data->uart, 9600);
+	serdev_device_set_flow_control(data->uart, false);
+
+	rf_kill = rfkill_alloc("GPS", &serdev->dev, RFKILL_TYPE_GPS,
+				&w2sg0004_rfkill_ops, data);
+	if (rf_kill == NULL) {
+		err = -ENOMEM;
+		goto err_rfkill;
+	}
+
+	err = rfkill_register(rf_kill);
+	if (err) {
+		dev_err(&serdev->dev, "Cannot register rfkill device\n");
+		goto err_rfkill;
+	}
+
+	data->rf_kill = rf_kill;
+
+	/* allocate the tty driver */
+	data->tty_drv = alloc_tty_driver(1);
+	if (!data->tty_drv)
+		return -ENOMEM;
+
+	/* initialize the tty driver */
+	data->tty_drv->owner = THIS_MODULE;
+	data->tty_drv->driver_name = "w2sg0004";
+	data->tty_drv->name = "ttyGPS";
+	data->tty_drv->major = 0;
+	data->tty_drv->minor_start = 0;
+	data->tty_drv->type = TTY_DRIVER_TYPE_SERIAL;
+	data->tty_drv->subtype = SERIAL_TYPE_NORMAL;
+	data->tty_drv->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+	data->tty_drv->init_termios = tty_std_termios;
+	data->tty_drv->init_termios.c_cflag = B9600 | CS8 | CREAD |
+					      HUPCL | CLOCAL;
+	/*
+	 * optional:
+	 * tty_termios_encode_baud_rate(&data->tty_drv->init_termios,
+					115200, 115200);
+	 * w2sg_tty_termios(&data->tty_drv->init_termios);
+	 */
+	tty_set_operations(data->tty_drv, &w2sg_serial_ops);
+
+	/* register the tty driver */
+	err = tty_register_driver(data->tty_drv);
+	if (err) {

drivers/misc/w2sg0004.c line 432

Quoted 8 lines

drivers/misc/w2sg0004.c new file +8 -0

+		pr_err("%s - tty_register_driver failed(%d)\n",
+			__func__, err);
+		put_tty_driver(data->tty_drv);
+		goto err_rfkill;
+	}
+
+	tty_port_init(&data->port);
+	data->port.ops = &w2sg_port_ops;

Quoted 31 lines

drivers/misc/w2sg0004.c new file +31 -0

+
+	pr_debug("w2sg call tty_port_register_device\n");
+
+	data->dev = tty_port_register_device(&data->port,
+			data->tty_drv, minor, &serdev->dev);
+
+	pr_debug("w2sg probed\n");
+
+	/* keep off until user space requests the device */
+	w2sg_set_power(data, false);
+
+	return 0;
+
+err_rfkill:
+	rfkill_destroy(rf_kill);
+	serdev_device_close(data->uart);
+out:
+	return err;
+}
+
+static void w2sg_remove(struct serdev_device *serdev)
+{
+	struct w2sg_data *data = serdev_device_get_drvdata(serdev);
+	int minor;
+
+	cancel_delayed_work_sync(&data->work);
+
+	/* what is the right sequence to avoid problems? */
+	serdev_device_close(data->uart);
+
+	minor = 0;

drivers/misc/w2sg0004.c line 469

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	tty_unregister_device(data->tty_drv, minor);
+
+	tty_unregister_driver(data->tty_drv);
+}
+
+static int w2sg_suspend(struct device *dev)

__maybe_unused, or if PM is disabled you will get a warning.

Quoted 67 lines

drivers/misc/w2sg0004.c new file +66 -0

+{
+	struct w2sg_data *data = dev_get_drvdata(dev);
+
+	data->suspended = true;
+
+	cancel_delayed_work_sync(&data->work);
+
+	w2sg_set_lna_power(data);	/* shuts down if needed */
+
+	if (data->state == W2SG_PULSE) {
+		msleep(10);
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->last_toggle = jiffies;
+		data->is_on = !data->is_on;
+		data->state = W2SG_NOPULSE;
+	}
+
+	if (data->state == W2SG_NOPULSE) {
+		msleep(10);
+		data->state = W2SG_IDLE;
+	}
+
+	if (data->is_on) {
+		pr_info("GPS off for suspend %d %d %d\n", data->requested,
+			data->is_on, data->lna_is_off);
+
+		gpio_set_value_cansleep(data->on_off_gpio, 0);
+		msleep(10);
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->is_on = 0;
+	}
+
+	return 0;
+}
+
+static int w2sg_resume(struct device *dev)
+{
+	struct w2sg_data *data = dev_get_drvdata(dev);
+
+	data->suspended = false;
+
+	pr_info("GPS resuming %d %d %d\n", data->requested,
+		data->is_on, data->lna_is_off);
+
+	schedule_delayed_work(&data->work, 0);	/* enables LNA if needed */
+
+	return 0;
+}
+
+static const struct of_device_id w2sg0004_of_match[] = {
+	{ .compatible = "wi2wi,w2sg0004" },
+	{ .compatible = "wi2wi,w2sg0084" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, w2sg0004_of_match);
+
+SIMPLE_DEV_PM_OPS(w2sg_pm_ops, w2sg_suspend, w2sg_resume);
+
+static struct serdev_device_driver w2sg_driver = {
+	.probe		= w2sg_probe,
+	.remove		= w2sg_remove,
+	.driver = {
+		.name	= "w2sg0004",
+		.owner	= THIS_MODULE,
+		.pm	= &w2sg_pm_ops,
+		.of_match_table = of_match_ptr(w2sg0004_of_match)

drivers/misc/w2sg0004.c line 541

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	},
+};
+
+module_serdev_device_driver(w2sg_driver);
+
+MODULE_ALIAS("w2sg0004");

Is this needed?

drivers/misc/w2sg0004.c line 543

Quoted 3 lines

drivers/misc/w2sg0004.c new file +2 -0

+
+MODULE_AUTHOR("NeilBrown <[email protected]>");

Who really wrote this?

drivers/misc/w2sg0004.c line 545

Quoted 4 lines

drivers/misc/w2sg0004.c new file +2 -0

+MODULE_DESCRIPTION("w2sg0004 GPS power management driver");
+MODULE_LICENSE("GPL v2");

Hi Andrew,
now as 4.15-rc1 is out I find time to continue this work and prepare [PATCH v5].

Quoted 20 lines

Am 23.11.2017 um 17:06 schrieb Andrew F. Davis <[email protected]>:

Quoted 17 lines · H. Nikolaus Schaller

Add driver for Wi2Wi W2SG0004/84 GPS module connected through uart.

Use serdev API hooks to monitor and forward the UART traffic to /dev/ttyGPSn and turn on/off the module. It also detects if the module is turned on (sends data) but should be off, e.g. if it was already turned on during boot or power-on-reset.

Additionally, rfkill block/unblock can be used to control an external LNA (and power down the module if not needed).

The driver concept is based on code developed by NeilBrown <[email protected]> but simplified and adapted to use the new serdev API introduced in 4.11.

Signed-off-by H. Nikolaus Schaller <[email protected]>

---

drivers/misc/Kconfig    |  10 +
drivers/misc/Makefile   |   1 +
drivers/misc/w2sg0004.c | 545 ++++++++++++++++++++++++++++++++++++++++++++++++

I wonder if this shouldn't better go to

drivers/gps

But this directory does not yet exist and has no overall maintainer. So it could be left in drivers/misc and moved as soon as drivers/gps is created elsewhere.

Quoted 35 lines

Quoted 35 lines

3 files changed, 556 insertions(+)

create mode 100644 drivers/misc/w2sg0004.c

drivers/misc/Kconfig +0 -0

index 8136dc7e863d..09d171d68408 100644
@@ -518,4 +518,14 @@ source "drivers/misc/mic/Kconfig"

source "drivers/misc/genwqe/Kconfig"
source "drivers/misc/echo/Kconfig"
source "drivers/misc/cxl/Kconfig"

drivers/misc/Kconfig +10 -0

+
+config W2SG0004
+	tristate "W2SG00x4 on/off control"
+	depends on GPIOLIB && SERIAL_DEV_BUS
+	help
+          Enable on/off control of W2SG00x4 GPS moduled connected
+	  to some SoC UART to allow powering up/down if the /dev/ttyGPSn
+	  is opened/closed.
+	  It also provides a rfkill gps name to control the LNA power.
+

endmenu

drivers/misc/Makefile +0 -0

index ad0e64fdba34..abcb667e0ff0 100644
@@ -51,6 +51,7 @@ obj-$(CONFIG_SRAM_EXEC)		+= sram-exec.o

obj-y += mic/
obj-$(CONFIG_GENWQE) += genwqe/
obj-$(CONFIG_ECHO) += echo/
+obj-$(CONFIG_W2SG0004) += w2sg0004.o
obj-$(CONFIG_VEXPRESS_SYSCFG) += vexpress-syscfg.o
obj-$(CONFIG_CXL_BASE) += cxl/
obj-$(CONFIG_ASPEED_LPC_CTRL) += aspeed-lpc-ctrl.o

drivers/misc/w2sg0004.c +0 -0

Quoted 8 lines

drivers/misc/w2sg0004.c line 1

Quoted 6 lines

new file mode 100644
index 000000000000..12e14b5e0a99

drivers/misc/w2sg0004.c new file +1 -0

@@ -0,0 +1,545 @@
+// SPDX-License-Identifier: GPL-2.0

Damn this looks ugly, oh well :/

I could remove it for [PATCH v5] ... :\

Quoted 7 lines

drivers/misc/w2sg0004.c line 4

Quoted 4 lines

drivers/misc/w2sg0004.c new file +3 -0

+/*
+ * Driver for power controlling the w2sg0004/w2sg0084 GPS receiver.
+ *

Think you still need copyright tag here somewhere.

At the bottom there is:

Quoted 3 lines

drivers/misc/w2sg0004.c line 545

Quoted 3 lines

drivers/misc/w2sg0004.c new file +3 -0

+MODULE_AUTHOR("NeilBrown <[email protected]>");
+MODULE_DESCRIPTION("w2sg0004 GPS power management driver");
+MODULE_LICENSE("GPL v2");

Isn't that enough any more?

Quoted 72 lines

Quoted 72 lines

drivers/misc/w2sg0004.c new file +71 -0

+ * This receiver has an ON/OFF pin which must be toggled to
+ * turn the device 'on' of 'off'.  A high->low->high toggle
+ * will switch the device on if it is off, and off if it is on.
+ *
+ * To enable receiving on/off requests we register with the
+ * UART power management notifications.
+ *
+ * It is not possible to directly detect the state of the device.
+ * However when it is on it will send characters on a UART line
+ * regularly.
+ *
+ * To detect that the power state is out of sync (e.g. if GPS
+ * was enabled before a reboot), we register for UART data received
+ * notifications.
+ *
+ * In addition we register as a rfkill client so that we can
+ * control the LNA power.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/rfkill.h>
+#include <linux/serdev.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/workqueue.h>
+
+/*
+ * There seems to be restrictions on how quickly we can toggle the
+ * on/off line.  data sheets says "two rtc ticks", whatever that means.
+ * If we do it too soon it doesn't work.
+ * So we have a state machine which uses the common work queue to ensure
+ * clean transitions.
+ * When a change is requested we record that request and only act on it
+ * once the previous change has completed.
+ * A change involves a 10ms low pulse, and a 990ms raised level, so only
+ * one change per second.
+ */
+
+enum w2sg_state {
+	W2SG_IDLE,	/* is not changing state */
+	W2SG_PULSE,	/* activate on/off impulse */
+	W2SG_NOPULSE	/* deactivate on/off impulse */
+};
+
+struct w2sg_data {
+	struct		rfkill *rf_kill;
+	struct		regulator *lna_regulator;
+	int		lna_blocked;	/* rfkill block gps active */
+	int		lna_is_off;	/* LNA is currently off */
+	int		is_on;		/* current state (0/1) */
+	unsigned long	last_toggle;
+	unsigned long	backoff;	/* time to wait since last_toggle */
+	int		on_off_gpio;	/* the on-off gpio number */
+	struct		serdev_device *uart;	/* uart connected to the chip */
+	struct		tty_driver *tty_drv;	/* this is the user space tty */
+	struct		device *dev;	/* from tty_port_register_device() */
+	struct		tty_port port;
+	int		open_count;	/* how often we were opened */
+	enum		w2sg_state state;

Quoted 8 lines

drivers/misc/w2sg0004.c line 81

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	int		requested;	/* requested state (0/1) */
+	int		suspended;
+	struct delayed_work work;
+	int		discard_count;
+};
+

Kernel doc style.

Is this really needed here?

For pure driver internal structs (they are not kernel infrastructure API) I usually consult the source code of a driver and never well formatted kernel doc. Hence I think readability by programmers looking into the source file is more important than serving kernel doc tools.

Yes, there are examples like:

https://elixir.free-electrons.com/linux/v4.15-rc1/source/drivers/iio/accel/mma8452.c#L113

But I find them more confusing than helpful because I have to jump between code lines to match the comment with the data type.

Quoted 5 lines

drivers/misc/w2sg0004.c line 86

Quoted 3 lines

drivers/misc/w2sg0004.c new file +2 -0

+static struct w2sg_data *w2sg_by_minor[1];
+

If you can only have one right now then just drop the array.

w2sg_get_by_minor() is prepared to access more than one record. And there are plans to have more than one (but I don't know exactly how to provide it).

Making it a non-array seems to be an unnecessary hurdle for such improvements. And regarding memory footprint, a single-element array is equivalent to a non-array.

Quoted 85 lines

Quoted 85 lines

drivers/misc/w2sg0004.c new file +84 -0

+static int w2sg_set_lna_power(struct w2sg_data *data)
+{
+	int ret = 0;
+	int off = data->suspended || !data->requested || data->lna_blocked;
+
+	pr_debug("%s: %s\n", __func__, off ? "off" : "on");
+
+	if (off != data->lna_is_off) {
+		data->lna_is_off = off;
+		if (!IS_ERR_OR_NULL(data->lna_regulator)) {
+			if (off)
+				regulator_disable(data->lna_regulator);
+			else
+				ret = regulator_enable(data->lna_regulator);
+		}
+	}
+
+	return ret;
+}
+
+static void w2sg_set_power(void *pdata, int val)
+{
+	struct w2sg_data *data = (struct w2sg_data *) pdata;
+
+	pr_debug("%s to state=%d (requested=%d)\n", __func__, val, data->requested);
+
+	if (val && !data->requested) {
+		data->requested = true;
+	} else if (!val && data->requested) {
+		data->backoff = HZ;
+		data->requested = false;
+	} else
+		return;
+
+	pr_debug("w2sg00x4 scheduled for %d\n", data->requested);
+
+	if (!data->suspended)
+		schedule_delayed_work(&data->work, 0);
+}
+
+/* called each time data is received by the UART (i.e. sent by the w2sg0004) */
+
+static int w2sg_uart_receive_buf(struct serdev_device *serdev,
+				const unsigned char *rxdata,
+				size_t count)
+{
+	struct w2sg_data *data =
+		(struct w2sg_data *) serdev_device_get_drvdata(serdev);
+
+	if (!data->requested && !data->is_on) {
+		/*
+		 * we have received characters while the w2sg
+		 * should have been be turned off
+		 */
+		data->discard_count += count;
+		if ((data->state == W2SG_IDLE) &&
+		    time_after(jiffies,
+		    data->last_toggle + data->backoff)) {
+			/* Should be off by now, time to toggle again */
+			pr_debug("w2sg00x4 has sent %d characters data although it should be off!\n",
+				data->discard_count);
+
+			data->discard_count = 0;
+
+			data->is_on = true;
+			data->backoff *= 2;
+			if (!data->suspended)
+				schedule_delayed_work(&data->work, 0);
+		}
+	} else if (data->open_count > 0) {
+		int n;
+
+		pr_debug("w2sg00x4: push %lu chars to tty port\n",
+			(unsigned long) count);
+
+		/* pass to user-space */
+		n = tty_insert_flip_string(&data->port, rxdata, count);
+		if (n != count)
+			pr_err("w2sg00x4: did loose %lu characters\n",
+				(unsigned long) (count - n));
+		tty_flip_buffer_push(&data->port);
+		return n;
+	}
+

Quoted 8 lines

drivers/misc/w2sg0004.c line 173

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	/* assume we have processed everything */
+	return count;
+}
+
+/* try to toggle the power state by sending a pulse to the on-off GPIO */
+

drop extra line, same everywhere

Ok! Was just this and one more location.

Quoted 134 lines

Quoted 134 lines

drivers/misc/w2sg0004.c new file +133 -0

+static void toggle_work(struct work_struct *work)
+{
+	struct w2sg_data *data = container_of(work, struct w2sg_data,
+					      work.work);
+
+	switch (data->state) {
+	case W2SG_IDLE:
+		if (data->requested == data->is_on)
+			return;
+
+		w2sg_set_lna_power(data);	/* update LNA power state */
+		gpio_set_value_cansleep(data->on_off_gpio, 0);
+		data->state = W2SG_PULSE;
+
+		pr_debug("w2sg: power gpio ON\n");
+
+		schedule_delayed_work(&data->work,
+				      msecs_to_jiffies(10));
+		break;
+
+	case W2SG_PULSE:
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->last_toggle = jiffies;
+		data->state = W2SG_NOPULSE;
+		data->is_on = !data->is_on;
+
+		pr_debug("w2sg: power gpio OFF\n");
+
+		schedule_delayed_work(&data->work,
+				      msecs_to_jiffies(10));
+		break;
+
+	case W2SG_NOPULSE:
+		data->state = W2SG_IDLE;
+
+		pr_debug("w2sg: idle\n");
+
+		break;
+
+	}
+}
+
+static int w2sg_rfkill_set_block(void *pdata, bool blocked)
+{
+	struct w2sg_data *data = pdata;
+
+	pr_debug("%s: blocked: %d\n", __func__, blocked);
+
+	data->lna_blocked = blocked;
+
+	return w2sg_set_lna_power(data);
+}
+
+static struct rfkill_ops w2sg0004_rfkill_ops = {
+	.set_block = w2sg_rfkill_set_block,
+};
+
+static struct serdev_device_ops serdev_ops = {
+	.receive_buf = w2sg_uart_receive_buf,
+};
+
+/*
+ * we are a man-in the middle between the user-space visible tty port
+ * and the serdev tty where the chip is connected.
+ * This allows us to recognise when the device should be powered on
+ * or off and handle the "false" state that data arrives while no
+ * users-space tty client exists.
+ */
+
+static struct w2sg_data *w2sg_get_by_minor(unsigned int minor)
+{
+	return w2sg_by_minor[minor];
+}
+
+static int w2sg_tty_install(struct tty_driver *driver, struct tty_struct *tty)
+{
+	struct w2sg_data *data;
+	int retval;
+
+	pr_debug("%s() tty = %p\n", __func__, tty);
+
+	data = w2sg_get_by_minor(tty->index);
+
+	if (!data)
+		return -ENODEV;
+
+	retval = tty_standard_install(driver, tty);
+	if (retval)
+		goto error_init_termios;
+
+	tty->driver_data = data;
+
+	return 0;
+
+error_init_termios:
+	tty_port_put(&data->port);
+	return retval;
+}
+
+static int w2sg_tty_open(struct tty_struct *tty, struct file *file)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	pr_debug("%s() data = %p open_count = ++%d\n", __func__, data, data->open_count);
+
+	w2sg_set_power(data, ++data->open_count > 0);
+
+	return tty_port_open(&data->port, tty, file);
+}
+
+static void w2sg_tty_close(struct tty_struct *tty, struct file *file)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	pr_debug("%s()\n", __func__);
+
+	w2sg_set_power(data, --data->open_count > 0);
+
+	tty_port_close(&data->port, tty, file);
+}
+
+static int w2sg_tty_write(struct tty_struct *tty,
+		const unsigned char *buffer, int count)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	/* simply pass down to UART */
+	return serdev_device_write_buf(data->uart, buffer, count);
+}
+
+static const struct tty_operations w2sg_serial_ops = {
+	.install = w2sg_tty_install,
+	.open = w2sg_tty_open,

Quoted 8 lines

drivers/misc/w2sg0004.c line 312

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	.close = w2sg_tty_close,
+	.write = w2sg_tty_write,
+};
+
+static const struct tty_port_operations w2sg_port_ops = {
+};

drop the brackets? or use NULL below, not sure if this needs memory.

This allocates a struct tty_port_operations initialized with NULL for all function pointers.

I am not sure if this is the same as providing no w2sg_port_ops at all.

Rather I think the serial core is only port == NULL safe but not port->ops == NULL e.g.:

http://elixir.free-electrons.com/linux/v4.15-rc1/source/drivers/tty/tty_port.c#L422

A test confirms (see comment below):

Quoted 15 lines

Quoted 15 lines

drivers/misc/w2sg0004.c new file +14 -0

+
+static int w2sg_probe(struct serdev_device *serdev)
+{
+	struct w2sg_data *data;
+	struct rfkill *rf_kill;
+	int err;
+	int minor;
+	enum of_gpio_flags flags;
+
+	pr_debug("%s()\n", __func__);
+
+	minor = 0;
+	if (w2sg_by_minor[minor]) {
+		pr_err("w2sg minor is already in use!\n");

Quoted 8 lines

drivers/misc/w2sg0004.c line 334

Quoted 8 lines

drivers/misc/w2sg0004.c new file +8 -0

+		return -ENODEV;
+	}
+
+	data = devm_kzalloc(&serdev->dev, sizeof(*data), GFP_KERNEL);
+	if (data == NULL)
+		return -ENOMEM;
+
+	w2sg_by_minor[minor] = data;

While looking through this, I found a potential issue if allocating the gpio fails with -EPROBE_DEFER.

Then, we have set w2sg_by_minor[minor] != NULL and the above test will already find it allocated on next deferred probe attempt.

So I'll move that to a position further down.

Quoted 90 lines

Quoted 90 lines

drivers/misc/w2sg0004.c new file +90 -0

+
+	serdev_device_set_drvdata(serdev, data);
+
+	data->on_off_gpio = of_get_named_gpio_flags(serdev->dev.of_node,
+						     "enable-gpios", 0,
+						     &flags);
+	/* defer until we have all gpios */
+	if (data->on_off_gpio == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	data->lna_regulator = devm_regulator_get_optional(&serdev->dev,
+							"lna");
+	if (IS_ERR(data->lna_regulator)) {
+		/* defer until we can get the regulator */
+		if (PTR_ERR(data->lna_regulator) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
+		data->lna_regulator = NULL;
+	}
+	pr_debug("%s() lna_regulator = %p\n", __func__, data->lna_regulator);
+
+	data->lna_blocked = true;
+	data->lna_is_off = true;
+
+	data->is_on = false;
+	data->requested = false;
+	data->state = W2SG_IDLE;
+	data->last_toggle = jiffies;
+	data->backoff = HZ;
+
+	data->uart = serdev;
+
+	INIT_DELAYED_WORK(&data->work, toggle_work);
+
+	err = devm_gpio_request(&serdev->dev, data->on_off_gpio,
+				"w2sg0004-on-off");
+	if (err < 0)
+		goto out;
+
+	gpio_direction_output(data->on_off_gpio, false);
+
+	serdev_device_set_client_ops(data->uart, &serdev_ops);
+	serdev_device_open(data->uart);
+
+	serdev_device_set_baudrate(data->uart, 9600);
+	serdev_device_set_flow_control(data->uart, false);
+
+	rf_kill = rfkill_alloc("GPS", &serdev->dev, RFKILL_TYPE_GPS,
+				&w2sg0004_rfkill_ops, data);
+	if (rf_kill == NULL) {
+		err = -ENOMEM;
+		goto err_rfkill;
+	}
+
+	err = rfkill_register(rf_kill);
+	if (err) {
+		dev_err(&serdev->dev, "Cannot register rfkill device\n");
+		goto err_rfkill;
+	}
+
+	data->rf_kill = rf_kill;
+
+	/* allocate the tty driver */
+	data->tty_drv = alloc_tty_driver(1);
+	if (!data->tty_drv)
+		return -ENOMEM;
+
+	/* initialize the tty driver */
+	data->tty_drv->owner = THIS_MODULE;
+	data->tty_drv->driver_name = "w2sg0004";
+	data->tty_drv->name = "ttyGPS";
+	data->tty_drv->major = 0;
+	data->tty_drv->minor_start = 0;
+	data->tty_drv->type = TTY_DRIVER_TYPE_SERIAL;
+	data->tty_drv->subtype = SERIAL_TYPE_NORMAL;
+	data->tty_drv->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+	data->tty_drv->init_termios = tty_std_termios;
+	data->tty_drv->init_termios.c_cflag = B9600 | CS8 | CREAD |
+					      HUPCL | CLOCAL;
+	/*
+	 * optional:
+	 * tty_termios_encode_baud_rate(&data->tty_drv->init_termios,
+					115200, 115200);
+	 * w2sg_tty_termios(&data->tty_drv->init_termios);
+	 */
+	tty_set_operations(data->tty_drv, &w2sg_serial_ops);
+
+	/* register the tty driver */
+	err = tty_register_driver(data->tty_drv);
+	if (err) {

Quoted 8 lines

drivers/misc/w2sg0004.c line 432

Quoted 8 lines

drivers/misc/w2sg0004.c new file +8 -0

+		pr_err("%s - tty_register_driver failed(%d)\n",
+			__func__, err);
+		put_tty_driver(data->tty_drv);
+		goto err_rfkill;
+	}
+
+	tty_port_init(&data->port);
+	data->port.ops = &w2sg_port_ops;

A test setting this to NULL leads to a kernel oops in:

[ 3048.821258] [<c046c598>] (tty_port_open) from [<c0466328>] (tty_open+0x1e8/0x2d8)

So we must define this completely empty struct w2sg_port_ops and pass a reference.

Quoted 31 lines

Quoted 31 lines

drivers/misc/w2sg0004.c new file +31 -0

+
+	pr_debug("w2sg call tty_port_register_device\n");
+
+	data->dev = tty_port_register_device(&data->port,
+			data->tty_drv, minor, &serdev->dev);
+
+	pr_debug("w2sg probed\n");
+
+	/* keep off until user space requests the device */
+	w2sg_set_power(data, false);
+
+	return 0;
+
+err_rfkill:
+	rfkill_destroy(rf_kill);
+	serdev_device_close(data->uart);
+out:
+	return err;
+}
+
+static void w2sg_remove(struct serdev_device *serdev)
+{
+	struct w2sg_data *data = serdev_device_get_drvdata(serdev);
+	int minor;
+
+	cancel_delayed_work_sync(&data->work);
+
+	/* what is the right sequence to avoid problems? */
+	serdev_device_close(data->uart);
+
+	minor = 0;

Quoted 8 lines

drivers/misc/w2sg0004.c line 469

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	tty_unregister_device(data->tty_drv, minor);
+
+	tty_unregister_driver(data->tty_drv);
+}
+
+static int w2sg_suspend(struct device *dev)

__maybe_unused, or if PM is disabled you will get a warning.

Ok.

Quoted 67 lines

Quoted 67 lines

drivers/misc/w2sg0004.c new file +66 -0

+{
+	struct w2sg_data *data = dev_get_drvdata(dev);
+
+	data->suspended = true;
+
+	cancel_delayed_work_sync(&data->work);
+
+	w2sg_set_lna_power(data);	/* shuts down if needed */
+
+	if (data->state == W2SG_PULSE) {
+		msleep(10);
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->last_toggle = jiffies;
+		data->is_on = !data->is_on;
+		data->state = W2SG_NOPULSE;
+	}
+
+	if (data->state == W2SG_NOPULSE) {
+		msleep(10);
+		data->state = W2SG_IDLE;
+	}
+
+	if (data->is_on) {
+		pr_info("GPS off for suspend %d %d %d\n", data->requested,
+			data->is_on, data->lna_is_off);
+
+		gpio_set_value_cansleep(data->on_off_gpio, 0);
+		msleep(10);
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->is_on = 0;
+	}
+
+	return 0;
+}
+
+static int w2sg_resume(struct device *dev)
+{
+	struct w2sg_data *data = dev_get_drvdata(dev);
+
+	data->suspended = false;
+
+	pr_info("GPS resuming %d %d %d\n", data->requested,
+		data->is_on, data->lna_is_off);
+
+	schedule_delayed_work(&data->work, 0);	/* enables LNA if needed */
+
+	return 0;
+}
+
+static const struct of_device_id w2sg0004_of_match[] = {
+	{ .compatible = "wi2wi,w2sg0004" },
+	{ .compatible = "wi2wi,w2sg0084" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, w2sg0004_of_match);
+
+SIMPLE_DEV_PM_OPS(w2sg_pm_ops, w2sg_suspend, w2sg_resume);
+
+static struct serdev_device_driver w2sg_driver = {
+	.probe		= w2sg_probe,
+	.remove		= w2sg_remove,
+	.driver = {
+		.name	= "w2sg0004",
+		.owner	= THIS_MODULE,
+		.pm	= &w2sg_pm_ops,
+		.of_match_table = of_match_ptr(w2sg0004_of_match)

Quoted 8 lines

drivers/misc/w2sg0004.c line 541

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	},
+};
+
+module_serdev_device_driver(w2sg_driver);
+
+MODULE_ALIAS("w2sg0004");

Is this needed?

Seems to be redundant.
After removal the driver is still loaded automatically after boot:

root at letux:~# modprobe -c | fgrep w2sg
alias of:N*T*Cwi2wi,w2sg0004 w2sg0004
alias of:N*T*Cwi2wi,w2sg0004C* w2sg0004
alias of:N*T*Cwi2wi,w2sg0084 w2sg0004
alias of:N*T*Cwi2wi,w2sg0084C* w2sg0004
root at letux:~# lsmod | fgrep w2sg
w2sg0004 16384 2
root at letux:~#

Quoted 5 lines

drivers/misc/w2sg0004.c line 543

Quoted 3 lines

drivers/misc/w2sg0004.c new file +2 -0

+
+MODULE_AUTHOR("NeilBrown <[email protected]>");

Who really wrote this?

Good question.

The problem is that with cleaning up the code and rewriting history over such a long time, it is no more visible.

But I have searched through our older branches:

Neil Brown had developed the first version for v3.7 in 2013:
http://git.goldelico.com/?p=gta04-kernel.git;a=commit;h=5b6fad7c7f15db8bb8e2c98ae9a50da52bda8b69

This is where the MODULE_AUTHOR line comes from.

Later, Marek Belisko worked on the UART driver, pinmux and interrupts.

And I have
* added lna-regulator and rfkill ca. v3.12
* added device tree support ca. v3.15
* moved to drivers/misc
* ported the code to serdev API ca. v4.11
* submitted to LKML and worked in comments by reviewers ca. 4.15

So this is the first version that is close to be acceptable.

Neil had also submitted different versions to LKML but I am not sure if he still is active anywhere.

I have also checked a diff between the v3.7 version and the current one and there are ca. 30-40% of lines original code by Neil.

So I'd say:

* Neil is the original author and a significant amount of untouched code lines and comments are still there
* he designed the overall driver architecture
* Hence he is the copyright holder, did license under GPL v2 and we have just made a derivative work out of it
* Neil did submit his version of serdev ca. 2015 (quite different from this) but resigned after review feedback
* I did add some important features but not the core code and driver architecture
* I feel my role as maintainer and massaging everything for DT, serdev and get it upstream, but not "the author"

How should we best reflect this in the AUTHOR macro?

Quoted 4 lines

drivers/misc/w2sg0004.c line 545

Quoted 4 lines

drivers/misc/w2sg0004.c new file +2 -0

+MODULE_DESCRIPTION("w2sg0004 GPS power management driver");
+MODULE_LICENSE("GPL v2");

BR and thanks,
Nikolaus Schaller

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo at vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

Am 29.11.2017 um 15:47 schrieb Andrew F. Davis <[email protected]>:

Quoted 28 lines · H. Nikolaus Schaller

Hi Andrew,
now as 4.15-rc1 is out I find time to continue this work and prepare [PATCH v5].

Quoted 20 lines

Am 23.11.2017 um 17:06 schrieb Andrew F. Davis <[email protected]>:

Quoted 17 lines · H. Nikolaus Schaller

Add driver for Wi2Wi W2SG0004/84 GPS module connected through uart.

Use serdev API hooks to monitor and forward the UART traffic to /dev/ttyGPSn and turn on/off the module. It also detects if the module is turned on (sends data) but should be off, e.g. if it was already turned on during boot or power-on-reset.

Additionally, rfkill block/unblock can be used to control an external LNA (and power down the module if not needed).

The driver concept is based on code developed by NeilBrown <[email protected]> but simplified and adapted to use the new serdev API introduced in 4.11.

Signed-off-by H. Nikolaus Schaller <[email protected]>

---

drivers/misc/Kconfig    |  10 +
drivers/misc/Makefile   |   1 +
drivers/misc/w2sg0004.c | 545 ++++++++++++++++++++++++++++++++++++++++++++++++

I wonder if this shouldn't better go to

drivers/gps

Quoted 4 lines

But this directory does not yet exist and has no overall maintainer. So it could be left in drivers/misc and moved as soon as drivers/gps is created elsewhere.

Making that directory would imply the existence of a GPS driver framework, until one comes about (or if you would like to create one), I think misc is the most appropriate spot for now.

Quoted 45 lines

Quoted 44 lines

Quoted 41 lines

3 files changed, 556 insertions(+)

create mode 100644 drivers/misc/w2sg0004.c

drivers/misc/Kconfig +0 -0

index 8136dc7e863d..09d171d68408 100644
@@ -518,4 +518,14 @@ source "drivers/misc/mic/Kconfig"

source "drivers/misc/genwqe/Kconfig"
source "drivers/misc/echo/Kconfig"
source "drivers/misc/cxl/Kconfig"

drivers/misc/Kconfig +10 -0

+
+config W2SG0004
+	tristate "W2SG00x4 on/off control"
+	depends on GPIOLIB && SERIAL_DEV_BUS
+	help
+          Enable on/off control of W2SG00x4 GPS moduled connected
+	  to some SoC UART to allow powering up/down if the /dev/ttyGPSn
+	  is opened/closed.
+	  It also provides a rfkill gps name to control the LNA power.
+

endmenu

drivers/misc/Makefile +0 -0

index ad0e64fdba34..abcb667e0ff0 100644
@@ -51,6 +51,7 @@ obj-$(CONFIG_SRAM_EXEC)		+= sram-exec.o

obj-y += mic/
obj-$(CONFIG_GENWQE) += genwqe/
obj-$(CONFIG_ECHO) += echo/
+obj-$(CONFIG_W2SG0004) += w2sg0004.o
obj-$(CONFIG_VEXPRESS_SYSCFG) += vexpress-syscfg.o
obj-$(CONFIG_CXL_BASE) += cxl/
obj-$(CONFIG_ASPEED_LPC_CTRL) += aspeed-lpc-ctrl.o

drivers/misc/w2sg0004.c new file +0 -0

new file mode 100644
index 000000000000..12e14b5e0a99

drivers/misc/w2sg0004.c line 1

Quoted 1 line

drivers/misc/w2sg0004.c new file +1 -0

@@ -0,0 +1,545 @@
+// SPDX-License-Identifier: GPL-2.0

Damn this looks ugly, oh well :/

Quoted 2 lines

I could remove it for [PATCH v5] ... :\

Nah, you should leave it, this comment was just me venting, Greg KH has spoken, so this is the correct way now.

Quoted 9 lines

Quoted 8 lines

drivers/misc/w2sg0004.c line 4

Quoted 5 lines

drivers/misc/w2sg0004.c new file +3 -0

+/*
+ * Driver for power controlling the w2sg0004/w2sg0084 GPS receiver.
+ *

Think you still need copyright tag here somewhere.

Quoted 8 lines

At the bottom there is:

Quoted 3 lines

drivers/misc/w2sg0004.c line 545

Quoted 3 lines

drivers/misc/w2sg0004.c new file +3 -0

+MODULE_AUTHOR("NeilBrown <[email protected]>");
+MODULE_DESCRIPTION("w2sg0004 GPS power management driver");
+MODULE_LICENSE("GPL v2");

Isn't that enough any more?

Not sure.. someone needs to hold the copyright to this file and it really should be close to the top.

Quoted 91 lines

Quoted 73 lines

Quoted 73 lines

drivers/misc/w2sg0004.c new file +71 -0

+ * This receiver has an ON/OFF pin which must be toggled to
+ * turn the device 'on' of 'off'.  A high->low->high toggle
+ * will switch the device on if it is off, and off if it is on.
+ *
+ * To enable receiving on/off requests we register with the
+ * UART power management notifications.
+ *
+ * It is not possible to directly detect the state of the device.
+ * However when it is on it will send characters on a UART line
+ * regularly.
+ *
+ * To detect that the power state is out of sync (e.g. if GPS
+ * was enabled before a reboot), we register for UART data received
+ * notifications.
+ *
+ * In addition we register as a rfkill client so that we can
+ * control the LNA power.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/rfkill.h>
+#include <linux/serdev.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/workqueue.h>
+
+/*
+ * There seems to be restrictions on how quickly we can toggle the
+ * on/off line.  data sheets says "two rtc ticks", whatever that means.
+ * If we do it too soon it doesn't work.
+ * So we have a state machine which uses the common work queue to ensure
+ * clean transitions.
+ * When a change is requested we record that request and only act on it
+ * once the previous change has completed.
+ * A change involves a 10ms low pulse, and a 990ms raised level, so only
+ * one change per second.
+ */
+
+enum w2sg_state {
+	W2SG_IDLE,	/* is not changing state */
+	W2SG_PULSE,	/* activate on/off impulse */
+	W2SG_NOPULSE	/* deactivate on/off impulse */
+};
+
+struct w2sg_data {
+	struct		rfkill *rf_kill;
+	struct		regulator *lna_regulator;
+	int		lna_blocked;	/* rfkill block gps active */
+	int		lna_is_off;	/* LNA is currently off */
+	int		is_on;		/* current state (0/1) */
+	unsigned long	last_toggle;
+	unsigned long	backoff;	/* time to wait since last_toggle */
+	int		on_off_gpio;	/* the on-off gpio number */
+	struct		serdev_device *uart;	/* uart connected to the chip */
+	struct		tty_driver *tty_drv;	/* this is the user space tty */
+	struct		device *dev;	/* from tty_port_register_device() */
+	struct		tty_port port;
+	int		open_count;	/* how often we were opened */
+	enum		w2sg_state state;

Quoted 8 lines

drivers/misc/w2sg0004.c line 81

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	int		requested;	/* requested state (0/1) */
+	int		suspended;
+	struct delayed_work work;
+	int		discard_count;
+};
+

Kernel doc style.

Is this really needed here?

For pure driver internal structs (they are not kernel infrastructure API) I usually consult the source code of a driver and never well formatted kernel doc. Hence I think readability by programmers looking into the source file is more important than serving kernel doc tools.

Yes, there are examples like:

Quoted 5 lines

https://elixir.free-electrons.com/linux/v4.15-rc1/source/drivers/iio/accel/mma8452.c#L113

But I find them more confusing than helpful because I have to jump between code lines to match the comment with the data type.

I have no strong preference here as long as you think this is the most readable way.

Quoted 7 lines

Quoted 6 lines

drivers/misc/w2sg0004.c line 86

Quoted 4 lines

drivers/misc/w2sg0004.c new file +2 -0

+static struct w2sg_data *w2sg_by_minor[1];
+

If you can only have one right now then just drop the array.

Quoted 4 lines

w2sg_get_by_minor() is prepared to access more than one record. And there are plans to have more than one (but I don't know exactly how to provide it).

Just add it back when you get that functionality.

Quoted 5 lines

Making it a non-array seems to be an unnecessary hurdle for such improvements. And regarding memory footprint, a single-element array is equivalent to a non-array.

This comment was not about memory footprint, it's about sane code practices.

Quoted 240 lines

Quoted 86 lines

Quoted 86 lines

drivers/misc/w2sg0004.c new file +84 -0

+static int w2sg_set_lna_power(struct w2sg_data *data)
+{
+	int ret = 0;
+	int off = data->suspended || !data->requested || data->lna_blocked;
+
+	pr_debug("%s: %s\n", __func__, off ? "off" : "on");
+
+	if (off != data->lna_is_off) {
+		data->lna_is_off = off;
+		if (!IS_ERR_OR_NULL(data->lna_regulator)) {
+			if (off)
+				regulator_disable(data->lna_regulator);
+			else
+				ret = regulator_enable(data->lna_regulator);
+		}
+	}
+
+	return ret;
+}
+
+static void w2sg_set_power(void *pdata, int val)
+{
+	struct w2sg_data *data = (struct w2sg_data *) pdata;
+
+	pr_debug("%s to state=%d (requested=%d)\n", __func__, val, data->requested);
+
+	if (val && !data->requested) {
+		data->requested = true;
+	} else if (!val && data->requested) {
+		data->backoff = HZ;
+		data->requested = false;
+	} else
+		return;
+
+	pr_debug("w2sg00x4 scheduled for %d\n", data->requested);
+
+	if (!data->suspended)
+		schedule_delayed_work(&data->work, 0);
+}
+
+/* called each time data is received by the UART (i.e. sent by the w2sg0004) */
+
+static int w2sg_uart_receive_buf(struct serdev_device *serdev,
+				const unsigned char *rxdata,
+				size_t count)
+{
+	struct w2sg_data *data =
+		(struct w2sg_data *) serdev_device_get_drvdata(serdev);
+
+	if (!data->requested && !data->is_on) {
+		/*
+		 * we have received characters while the w2sg
+		 * should have been be turned off
+		 */
+		data->discard_count += count;
+		if ((data->state == W2SG_IDLE) &&
+		    time_after(jiffies,
+		    data->last_toggle + data->backoff)) {
+			/* Should be off by now, time to toggle again */
+			pr_debug("w2sg00x4 has sent %d characters data although it should be off!\n",
+				data->discard_count);
+
+			data->discard_count = 0;
+
+			data->is_on = true;
+			data->backoff *= 2;
+			if (!data->suspended)
+				schedule_delayed_work(&data->work, 0);
+		}
+	} else if (data->open_count > 0) {
+		int n;
+
+		pr_debug("w2sg00x4: push %lu chars to tty port\n",
+			(unsigned long) count);
+
+		/* pass to user-space */
+		n = tty_insert_flip_string(&data->port, rxdata, count);
+		if (n != count)
+			pr_err("w2sg00x4: did loose %lu characters\n",
+				(unsigned long) (count - n));
+		tty_flip_buffer_push(&data->port);
+		return n;
+	}
+

Quoted 8 lines

drivers/misc/w2sg0004.c line 173

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	/* assume we have processed everything */
+	return count;
+}
+
+/* try to toggle the power state by sending a pulse to the on-off GPIO */
+

drop extra line, same everywhere

Ok! Was just this and one more location.

Quoted 134 lines

Quoted 134 lines

drivers/misc/w2sg0004.c new file +133 -0

+static void toggle_work(struct work_struct *work)
+{
+	struct w2sg_data *data = container_of(work, struct w2sg_data,
+					      work.work);
+
+	switch (data->state) {
+	case W2SG_IDLE:
+		if (data->requested == data->is_on)
+			return;
+
+		w2sg_set_lna_power(data);	/* update LNA power state */
+		gpio_set_value_cansleep(data->on_off_gpio, 0);
+		data->state = W2SG_PULSE;
+
+		pr_debug("w2sg: power gpio ON\n");
+
+		schedule_delayed_work(&data->work,
+				      msecs_to_jiffies(10));
+		break;
+
+	case W2SG_PULSE:
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->last_toggle = jiffies;
+		data->state = W2SG_NOPULSE;
+		data->is_on = !data->is_on;
+
+		pr_debug("w2sg: power gpio OFF\n");
+
+		schedule_delayed_work(&data->work,
+				      msecs_to_jiffies(10));
+		break;
+
+	case W2SG_NOPULSE:
+		data->state = W2SG_IDLE;
+
+		pr_debug("w2sg: idle\n");
+
+		break;
+
+	}
+}
+
+static int w2sg_rfkill_set_block(void *pdata, bool blocked)
+{
+	struct w2sg_data *data = pdata;
+
+	pr_debug("%s: blocked: %d\n", __func__, blocked);
+
+	data->lna_blocked = blocked;
+
+	return w2sg_set_lna_power(data);
+}
+
+static struct rfkill_ops w2sg0004_rfkill_ops = {
+	.set_block = w2sg_rfkill_set_block,
+};
+
+static struct serdev_device_ops serdev_ops = {
+	.receive_buf = w2sg_uart_receive_buf,
+};
+
+/*
+ * we are a man-in the middle between the user-space visible tty port
+ * and the serdev tty where the chip is connected.
+ * This allows us to recognise when the device should be powered on
+ * or off and handle the "false" state that data arrives while no
+ * users-space tty client exists.
+ */
+
+static struct w2sg_data *w2sg_get_by_minor(unsigned int minor)
+{
+	return w2sg_by_minor[minor];
+}
+
+static int w2sg_tty_install(struct tty_driver *driver, struct tty_struct *tty)
+{
+	struct w2sg_data *data;
+	int retval;
+
+	pr_debug("%s() tty = %p\n", __func__, tty);
+
+	data = w2sg_get_by_minor(tty->index);
+
+	if (!data)
+		return -ENODEV;
+
+	retval = tty_standard_install(driver, tty);
+	if (retval)
+		goto error_init_termios;
+
+	tty->driver_data = data;
+
+	return 0;
+
+error_init_termios:
+	tty_port_put(&data->port);
+	return retval;
+}
+
+static int w2sg_tty_open(struct tty_struct *tty, struct file *file)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	pr_debug("%s() data = %p open_count = ++%d\n", __func__, data, data->open_count);
+
+	w2sg_set_power(data, ++data->open_count > 0);
+
+	return tty_port_open(&data->port, tty, file);
+}
+
+static void w2sg_tty_close(struct tty_struct *tty, struct file *file)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	pr_debug("%s()\n", __func__);
+
+	w2sg_set_power(data, --data->open_count > 0);
+
+	tty_port_close(&data->port, tty, file);
+}
+
+static int w2sg_tty_write(struct tty_struct *tty,
+		const unsigned char *buffer, int count)
+{
+	struct w2sg_data *data = tty->driver_data;
+
+	/* simply pass down to UART */
+	return serdev_device_write_buf(data->uart, buffer, count);
+}
+
+static const struct tty_operations w2sg_serial_ops = {
+	.install = w2sg_tty_install,
+	.open = w2sg_tty_open,

Quoted 8 lines

drivers/misc/w2sg0004.c line 312

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	.close = w2sg_tty_close,
+	.write = w2sg_tty_write,
+};
+
+static const struct tty_port_operations w2sg_port_ops = {
+};

drop the brackets? or use NULL below, not sure if this needs memory.

Quoted 3 lines

This allocates a struct tty_port_operations initialized with NULL for all function pointers.

Then just drop the brackets, or allocate it with kzalloc.

Quoted 315 lines

I am not sure if this is the same as providing no w2sg_port_ops at all.

Rather I think the serial core is only port == NULL safe but not port->ops == NULL e.g.:

http://elixir.free-electrons.com/linux/v4.15-rc1/source/drivers/tty/tty_port.c#L422

A test confirms (see comment below):

Quoted 15 lines

Quoted 15 lines

drivers/misc/w2sg0004.c new file +14 -0

+
+static int w2sg_probe(struct serdev_device *serdev)
+{
+	struct w2sg_data *data;
+	struct rfkill *rf_kill;
+	int err;
+	int minor;
+	enum of_gpio_flags flags;
+
+	pr_debug("%s()\n", __func__);
+
+	minor = 0;
+	if (w2sg_by_minor[minor]) {
+		pr_err("w2sg minor is already in use!\n");

Quoted 8 lines

drivers/misc/w2sg0004.c line 334

Quoted 8 lines

drivers/misc/w2sg0004.c new file +8 -0

+		return -ENODEV;
+	}
+
+	data = devm_kzalloc(&serdev->dev, sizeof(*data), GFP_KERNEL);
+	if (data == NULL)
+		return -ENOMEM;
+
+	w2sg_by_minor[minor] = data;

While looking through this, I found a potential issue if allocating the gpio fails with -EPROBE_DEFER.

Then, we have set w2sg_by_minor[minor] != NULL and the above test will already find it allocated on next deferred probe attempt.

So I'll move that to a position further down.

Quoted 90 lines

Quoted 90 lines

drivers/misc/w2sg0004.c new file +90 -0

+
+	serdev_device_set_drvdata(serdev, data);
+
+	data->on_off_gpio = of_get_named_gpio_flags(serdev->dev.of_node,
+						     "enable-gpios", 0,
+						     &flags);
+	/* defer until we have all gpios */
+	if (data->on_off_gpio == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	data->lna_regulator = devm_regulator_get_optional(&serdev->dev,
+							"lna");
+	if (IS_ERR(data->lna_regulator)) {
+		/* defer until we can get the regulator */
+		if (PTR_ERR(data->lna_regulator) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
+		data->lna_regulator = NULL;
+	}
+	pr_debug("%s() lna_regulator = %p\n", __func__, data->lna_regulator);
+
+	data->lna_blocked = true;
+	data->lna_is_off = true;
+
+	data->is_on = false;
+	data->requested = false;
+	data->state = W2SG_IDLE;
+	data->last_toggle = jiffies;
+	data->backoff = HZ;
+
+	data->uart = serdev;
+
+	INIT_DELAYED_WORK(&data->work, toggle_work);
+
+	err = devm_gpio_request(&serdev->dev, data->on_off_gpio,
+				"w2sg0004-on-off");
+	if (err < 0)
+		goto out;
+
+	gpio_direction_output(data->on_off_gpio, false);
+
+	serdev_device_set_client_ops(data->uart, &serdev_ops);
+	serdev_device_open(data->uart);
+
+	serdev_device_set_baudrate(data->uart, 9600);
+	serdev_device_set_flow_control(data->uart, false);
+
+	rf_kill = rfkill_alloc("GPS", &serdev->dev, RFKILL_TYPE_GPS,
+				&w2sg0004_rfkill_ops, data);
+	if (rf_kill == NULL) {
+		err = -ENOMEM;
+		goto err_rfkill;
+	}
+
+	err = rfkill_register(rf_kill);
+	if (err) {
+		dev_err(&serdev->dev, "Cannot register rfkill device\n");
+		goto err_rfkill;
+	}
+
+	data->rf_kill = rf_kill;
+
+	/* allocate the tty driver */
+	data->tty_drv = alloc_tty_driver(1);
+	if (!data->tty_drv)
+		return -ENOMEM;
+
+	/* initialize the tty driver */
+	data->tty_drv->owner = THIS_MODULE;
+	data->tty_drv->driver_name = "w2sg0004";
+	data->tty_drv->name = "ttyGPS";
+	data->tty_drv->major = 0;
+	data->tty_drv->minor_start = 0;
+	data->tty_drv->type = TTY_DRIVER_TYPE_SERIAL;
+	data->tty_drv->subtype = SERIAL_TYPE_NORMAL;
+	data->tty_drv->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+	data->tty_drv->init_termios = tty_std_termios;
+	data->tty_drv->init_termios.c_cflag = B9600 | CS8 | CREAD |
+					      HUPCL | CLOCAL;
+	/*
+	 * optional:
+	 * tty_termios_encode_baud_rate(&data->tty_drv->init_termios,
+					115200, 115200);
+	 * w2sg_tty_termios(&data->tty_drv->init_termios);
+	 */
+	tty_set_operations(data->tty_drv, &w2sg_serial_ops);
+
+	/* register the tty driver */
+	err = tty_register_driver(data->tty_drv);
+	if (err) {

Quoted 8 lines

drivers/misc/w2sg0004.c line 432

Quoted 8 lines

drivers/misc/w2sg0004.c new file +8 -0

+		pr_err("%s - tty_register_driver failed(%d)\n",
+			__func__, err);
+		put_tty_driver(data->tty_drv);
+		goto err_rfkill;
+	}
+
+	tty_port_init(&data->port);
+	data->port.ops = &w2sg_port_ops;

A test setting this to NULL leads to a kernel oops in:

[ 3048.821258] [<c046c598>] (tty_port_open) from [<c0466328>] (tty_open+0x1e8/0x2d8)

So we must define this completely empty struct w2sg_port_ops and pass a reference.

Quoted 31 lines

Quoted 31 lines

drivers/misc/w2sg0004.c new file +31 -0

+
+	pr_debug("w2sg call tty_port_register_device\n");
+
+	data->dev = tty_port_register_device(&data->port,
+			data->tty_drv, minor, &serdev->dev);
+
+	pr_debug("w2sg probed\n");
+
+	/* keep off until user space requests the device */
+	w2sg_set_power(data, false);
+
+	return 0;
+
+err_rfkill:
+	rfkill_destroy(rf_kill);
+	serdev_device_close(data->uart);
+out:
+	return err;
+}
+
+static void w2sg_remove(struct serdev_device *serdev)
+{
+	struct w2sg_data *data = serdev_device_get_drvdata(serdev);
+	int minor;
+
+	cancel_delayed_work_sync(&data->work);
+
+	/* what is the right sequence to avoid problems? */
+	serdev_device_close(data->uart);
+
+	minor = 0;

Quoted 8 lines

drivers/misc/w2sg0004.c line 469

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	tty_unregister_device(data->tty_drv, minor);
+
+	tty_unregister_driver(data->tty_drv);
+}
+
+static int w2sg_suspend(struct device *dev)

__maybe_unused, or if PM is disabled you will get a warning.

Ok.

Quoted 67 lines

Quoted 67 lines

drivers/misc/w2sg0004.c new file +66 -0

+{
+	struct w2sg_data *data = dev_get_drvdata(dev);
+
+	data->suspended = true;
+
+	cancel_delayed_work_sync(&data->work);
+
+	w2sg_set_lna_power(data);	/* shuts down if needed */
+
+	if (data->state == W2SG_PULSE) {
+		msleep(10);
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->last_toggle = jiffies;
+		data->is_on = !data->is_on;
+		data->state = W2SG_NOPULSE;
+	}
+
+	if (data->state == W2SG_NOPULSE) {
+		msleep(10);
+		data->state = W2SG_IDLE;
+	}
+
+	if (data->is_on) {
+		pr_info("GPS off for suspend %d %d %d\n", data->requested,
+			data->is_on, data->lna_is_off);
+
+		gpio_set_value_cansleep(data->on_off_gpio, 0);
+		msleep(10);
+		gpio_set_value_cansleep(data->on_off_gpio, 1);
+		data->is_on = 0;
+	}
+
+	return 0;
+}
+
+static int w2sg_resume(struct device *dev)
+{
+	struct w2sg_data *data = dev_get_drvdata(dev);
+
+	data->suspended = false;
+
+	pr_info("GPS resuming %d %d %d\n", data->requested,
+		data->is_on, data->lna_is_off);
+
+	schedule_delayed_work(&data->work, 0);	/* enables LNA if needed */
+
+	return 0;
+}
+
+static const struct of_device_id w2sg0004_of_match[] = {
+	{ .compatible = "wi2wi,w2sg0004" },
+	{ .compatible = "wi2wi,w2sg0084" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, w2sg0004_of_match);
+
+SIMPLE_DEV_PM_OPS(w2sg_pm_ops, w2sg_suspend, w2sg_resume);
+
+static struct serdev_device_driver w2sg_driver = {
+	.probe		= w2sg_probe,
+	.remove		= w2sg_remove,
+	.driver = {
+		.name	= "w2sg0004",
+		.owner	= THIS_MODULE,
+		.pm	= &w2sg_pm_ops,
+		.of_match_table = of_match_ptr(w2sg0004_of_match)

Quoted 8 lines

drivers/misc/w2sg0004.c line 541

Quoted 6 lines

drivers/misc/w2sg0004.c new file +6 -0

+	},
+};
+
+module_serdev_device_driver(w2sg_driver);
+
+MODULE_ALIAS("w2sg0004");

Is this needed?

Seems to be redundant.
After removal the driver is still loaded automatically after boot:

root at letux:~# modprobe -c | fgrep w2sg
alias of:N*T*Cwi2wi,w2sg0004 w2sg0004
alias of:N*T*Cwi2wi,w2sg0004C* w2sg0004
alias of:N*T*Cwi2wi,w2sg0084 w2sg0004
alias of:N*T*Cwi2wi,w2sg0084C* w2sg0004
root at letux:~# lsmod | fgrep w2sg
w2sg0004 16384 2
root at letux:~#

Quoted 5 lines

drivers/misc/w2sg0004.c line 543

Quoted 3 lines

drivers/misc/w2sg0004.c new file +2 -0

+
+MODULE_AUTHOR("NeilBrown <[email protected]>");

Who really wrote this?

Good question.

The problem is that with cleaning up the code and rewriting history over such a long time, it is no more visible.

But I have searched through our older branches:

Neil Brown had developed the first version for v3.7 in 2013:
http://git.goldelico.com/?p=gta04-kernel.git;a=commit;h=5b6fad7c7f15db8bb8e2c98ae9a50da52bda8b69

This is where the MODULE_AUTHOR line comes from.

Later, Marek Belisko worked on the UART driver, pinmux and interrupts.

And I have
* added lna-regulator and rfkill ca. v3.12
* added device tree support ca. v3.15
* moved to drivers/misc
* ported the code to serdev API ca. v4.11
* submitted to LKML and worked in comments by reviewers ca. 4.15

So this is the first version that is close to be acceptable.

Neil had also submitted different versions to LKML but I am not sure if he still is active anywhere.

I have also checked a diff between the v3.7 version and the current one and there are ca. 30-40% of lines original code by Neil.

So I'd say:

Quoted 9 lines

* Neil is the original author and a significant amount of untouched code lines and comments are still there
* he designed the overall driver architecture
* Hence he is the copyright holder, did license under GPL v2 and we have just made a derivative work out of it
* Neil did submit his version of serdev ca. 2015 (quite different from this) but resigned after review feedback
* I did add some important features but not the core code and driver architecture
* I feel my role as maintainer and massaging everything for DT, serdev and get it upstream, but not "the author"

How should we best reflect this in the AUTHOR macro?

Easy:

MODULE_AUTHOR("NeilBrown <[email protected]>"); MODULE_AUTHOR("H. Nikolaus Schaller <[email protected]>");

you can have more than one :)

Quoted 5 lines

Quoted 5 lines

drivers/misc/w2sg0004.c line 545

Quoted 5 lines

drivers/misc/w2sg0004.c new file +2 -0

+MODULE_DESCRIPTION("w2sg0004 GPS power management driver");
+MODULE_LICENSE("GPL v2");

GTA04 has a W2SG0004/84 connected to UART2 of the OMAP3 processor. A GPIO can pulse the on/off toggle switch.

The VSIM regulator is used to power on/off the LNA of an external active GPS antenna so that a driver can turn the LNA off if GPS is not needed to save battery energy.

Signed-off-by H. Nikolaus Schaller <[email protected]>

---
 arch/arm/boot/dts/omap3-gta04.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

arch/arm/boot/dts/omap3-gta04.dtsi +0 -0

index 4504908c23fe..e967d738aaaf 100644

Am 17.11.2017 um 18:08 schrieb Tony Lindgren <[email protected]>:

Quoted 17 lines · H. Nikolaus Schaller

GTA04 has a W2SG0004/84 connected to UART2 of the OMAP3 processor. A GPIO can pulse the on/off toggle switch.

The VSIM regulator is used to power on/off the LNA of an external active GPS antenna so that a driver can turn the LNA off if GPS is not needed to save battery energy.

Signed-off-by H. Nikolaus Schaller <[email protected]>

---
arch/arm/boot/dts/omap3-gta04.dtsi | 6 ++++++

1 file changed, 6 insertions(+)

arch/arm/boot/dts/omap3-gta04.dtsi +0 -0

index 4504908c23fe..e967d738aaaf 100644

arch/arm/boot/dts/omap3-gta04.dtsi line 486

Quoted 10 lines

arch/arm/boot/dts/omap3-gta04.dtsi +6 -0

@@ -477,6 +477,12 @@
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart2_pins>;
+
+	gps: gps {
+		compatible = "wi2wi,w2sg0004";
+		lna-supply = <&vsim>;   /* LNA regulator */
+		enable-gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>;    /* GPIO_145: trigger for turning on/off w2sg0004 */
+	};
 };

How about move the comment above the node to avoid long lines? Or just change it to gpio_145 for the comment as the property is already enable-gpios?

Regards,

Tony