board: Add Allwinner A64/H5 boards

index 7b1cc6e..5b4e3b0 100644
@@ -28,21 +28,25 @@ ARM_TRUSTED_FIRMWARE_INSTALL_IMAGES = YES
 
 ARM_TRUSTED_FIRMWARE_PLATFORM = $(call qstrip,$(BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM))
 
+ARM_TRUSTED_FIRMWARE_CMDS += all
+
 ARM_TRUSTED_FIRMWARE_MAKE_OPTS += \
 	CROSS_COMPILE="$(TARGET_CROSS)" \
-	BL33=$(BINARIES_DIR)/u-boot.bin \
 	$(call qstrip,$(BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES)) \
 	PLAT=$(ARM_TRUSTED_FIRMWARE_PLATFORM)
 
 ifeq ($(BR2_TARGET_VEXPRESS_FIRMWARE),y)
-ARM_TRUSTED_FIRMWARE_MAKE_OPTS += SCP_BL2=$(BINARIES_DIR)/scp-fw.bin
 ARM_TRUSTED_FIRMWARE_DEPENDENCIES += vexpress-firmware
+ARM_TRUSTED_FIRMWARE_MAKE_OPTS += \
+	BL33=$(BINARIES_DIR)/u-boot.bin \
+	SCP_BL2=$(BINARIES_DIR)/scp-fw.bin
+ARM_TRUSTED_FIRMWARE_CMDS += fip
 endif
 
 define ARM_TRUSTED_FIRMWARE_BUILD_CMDS
 	$(TARGET_CONFIGURE_OPTS) \
 		$(MAKE) -C $(@D) $(ARM_TRUSTED_FIRMWARE_MAKE_OPTS) \
-			all fip
+			$(ARM_TRUSTED_FIRMWARE_CMDS)
 endef
 
 define ARM_TRUSTED_FIRMWARE_INSTALL_IMAGES_CMDS

index 5b4e3b0..c0af8e8 100644
@@ -8,7 +8,9 @@ ARM_TRUSTED_FIRMWARE_VERSION = $(call qstrip,$(BR2_TARGET_ARM_TRUSTED_FIRMWARE_V
 ARM_TRUSTED_FIRMWARE_LICENSE = BSD-3-Clause
 ARM_TRUSTED_FIRMWARE_LICENSE_FILES = license.rst
 
+ifeq ($(BR2_TARGET_UBOOT_NEEDS_ATF),)
 ARM_TRUSTED_FIRMWARE_DEPENDENCIES += uboot
+endif
 
 ifeq ($(ARM_TRUSTED_FIRMWARE_VERSION),custom)
 # Handle custom ATF tarballs as specified by the configuration

index 8215912..4751593 100644
@@ -158,6 +158,16 @@ config BR2_TARGET_UBOOT_NEEDS_OPENSSL
 	  typically the case when the board configuration has
 	  CONFIG_FIT_SIGNATURE enabled.
 
+config BR2_TARGET_UBOOT_NEEDS_ATF
+	bool "U-Boot needs ATF"
+	depends on BR2_TARGET_ARM_TRUSTED_FIRMWARE
+	help
+	  For building U-Boot proper in Allwinner A64/H5, ATF need
+	  to build first and ATF binary need to be exported.
+	  This config typically export ATF binary and disable
+	  U-Boot dependency in ATF becuase except U-Boot dependent
+	  boards(like juno) ideally ATF will build prior to U-Boot.
+
 menu "U-Boot binary format"
 
 config BR2_TARGET_UBOOT_FORMAT_AIS

index fdacf16..cbd2225 100644
@@ -134,6 +134,11 @@ UBOOT_MAKE_OPTS += \
 	HOSTCC="$(HOSTCC) $(HOST_CFLAGS)" \
 	HOSTLDFLAGS="$(HOST_LDFLAGS)"
 
+ifeq ($(BR2_TARGET_UBOOT_NEEDS_ATF),y)
+UBOOT_MAKE_OPTS += \
+	BL31=${BUILD_DIR}/arm-trusted-firmware-${BR2_TARGET_ARM_TRUSTED_FIRMWARE_VERSION}/build/${BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM}/release/${BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES}.bin
+endif
+
 ifeq ($(BR2_TARGET_UBOOT_NEEDS_DTC),y)
 UBOOT_DEPENDENCIES += host-dtc
 endif

index ebaac7a..3dd4f48 100644
@@ -90,6 +90,7 @@ atmel_sama5d4_xplained_mmc_defconfig: *defconfig
 atmel_sama5d4_xplained_mmc_dev_defconfig: *defconfig
 bananapi_m1_defconfig: *defconfig
 bananapi_m2_plus_defconfig: *defconfig
+bananapi_m64_defconfig: *defconfig
 bananapro_defconfig: *defconfig
 beagleboardx15_defconfig: *defconfig
 beaglebone_defconfig: *defconfig

index 51283f1..6521aad 100644
@@ -729,6 +729,7 @@ N:	Jagan Teki <[email protected]>
 F:	board/bananapi/
 F:	board/engicam/
 F:	configs/bananapi_m1_defconfig
+F:	configs/bananapi_m64_defconfig
 F:	configs/engicam_imx6qdl_icore_defconfig
 F:	configs/engicam_imx6qdl_icore_qt5_defconfig
 F:	configs/engicam_imx6qdl_icore_rqs_defconfig

new file mode 100644
index 0000000..d35c9b0
@@ -0,0 +1,6 @@
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r Image
+fatload mmc 0 $fdt_addr_r sun50i-a64-bananapi-m64.dtb
+
+booti $kernel_addr_r - $fdt_addr_r

new file mode 100644
index 0000000..891217c
@@ -0,0 +1,38 @@
+image boot.vfat {
+	vfat {
+		files = {
+			"Image",
+			"sun50i-a64-bananapi-m64.dtb",
+			"boot.scr"
+		}
+	}
+	size = 64M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition spl {
+		in-partition-table = "no"
+		image = "sunxi-spl.bin"
+		offset = 8192
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot.itb"
+		offset = 40K
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100644
index 0000000..0dec3e5
@@ -0,0 +1,37 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the Bananapi M64. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+Bananapi M64 link:
+http://www.banana-pi.org/m64.html
+
+Wiki link:
+https://openedev.amarulasolutions.com/display/ODWIKI/Bananapi+M64
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+How to build
+============
+
+    $ make bananapi_m64_defconfig
+    $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+  $ sudo sync
+
+Insert the micro SDcard in your Bananapi M64 and power it up. The console
+is on the serial line, 115200 8N1.

47 lines not on this page · raw message

index 3dd4f48..44edc61 100644
@@ -161,6 +161,7 @@ orangepi_zero_defconfig: *defconfig
 pandaboard_defconfig: *defconfig
 pc_x86_64_bios_defconfig: *defconfig
 pc_x86_64_efi_defconfig: *defconfig
+pine64_defconfig: *defconfig
 qemu_aarch64_virt_defconfig: *defconfig
 qemu_arm_versatile_defconfig: *defconfig
 qemu_arm_versatile_nommu_defconfig: *defconfig

index 6521aad..780c674 100644
@@ -728,8 +728,10 @@ F:	package/keepalived/
 N:	Jagan Teki <[email protected]>
 F:	board/bananapi/
 F:	board/engicam/
+F:	board/pine64/
 F:	configs/bananapi_m1_defconfig
 F:	configs/bananapi_m64_defconfig
+F:	configs/pine64_defconfig
 F:	configs/engicam_imx6qdl_icore_defconfig
 F:	configs/engicam_imx6qdl_icore_qt5_defconfig
 F:	configs/engicam_imx6qdl_icore_rqs_defconfig

new file mode 100644
index 0000000..14f5610
@@ -0,0 +1,6 @@
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r Image
+fatload mmc 0 $fdt_addr_r sun50i-a64-pine64.dtb
+
+booti $kernel_addr_r - $fdt_addr_r

new file mode 100644
index 0000000..8e12308
@@ -0,0 +1,38 @@
+image boot.vfat {
+	vfat {
+		files = {
+			"Image",
+			"sun50i-a64-pine64.dtb",
+			"boot.scr"
+		}
+	}
+	size = 64M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition spl {
+		in-partition-table = "no"
+		image = "sunxi-spl.bin"
+		offset = 8192
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot.itb"
+		offset = 40K
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100644
index 0000000..85226fd
@@ -0,0 +1,38 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the Pine64. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+Pine64 link:
+https://www.pine64.org/?page_id=1194
+
+Wiki link:
+https://openedev.amarulasolutions.com/display/ODWIKI/Pine64
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+How to build
+============
+
+    $ make pine64_defconfig
+
+    $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+  $ sudo sync
+
+Insert the micro SDcard in your Pine64 and power it up. The console
+is on the serial line, 115200 8N1.

47 lines not on this page · raw message

index 44edc61..a690b17 100644
@@ -162,6 +162,7 @@ pandaboard_defconfig: *defconfig
 pc_x86_64_bios_defconfig: *defconfig
 pc_x86_64_efi_defconfig: *defconfig
 pine64_defconfig: *defconfig
+pine64_sopine_defconfig: *defconfig
 qemu_aarch64_virt_defconfig: *defconfig
 qemu_arm_versatile_defconfig: *defconfig
 qemu_arm_versatile_nommu_defconfig: *defconfig

index 780c674..106d793 100644
@@ -732,6 +732,7 @@ F:	board/pine64/
 F:	configs/bananapi_m1_defconfig
 F:	configs/bananapi_m64_defconfig
 F:	configs/pine64_defconfig
+F:	configs/pine64_sopine_defconfig
 F:	configs/engicam_imx6qdl_icore_defconfig
 F:	configs/engicam_imx6qdl_icore_qt5_defconfig
 F:	configs/engicam_imx6qdl_icore_rqs_defconfig

new file mode 100644
index 0000000..2eab642
@@ -0,0 +1,6 @@
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r Image
+fatload mmc 0 $fdt_addr_r sun50i-a64-sopine-baseboard.dtb
+
+booti $kernel_addr_r - $fdt_addr_r

new file mode 100644
index 0000000..5606d34
@@ -0,0 +1,38 @@
+image boot.vfat {
+	vfat {
+		files = {
+			"Image",
+			"sun50i-a64-sopine-baseboard.dtb",
+			"boot.scr"
+		}
+	}
+	size = 64M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition spl {
+		in-partition-table = "no"
+		image = "sunxi-spl.bin"
+		offset = 8192
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot.itb"
+		offset = 40K
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100644
index 0000000..08cb380
@@ -0,0 +1,38 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the SoPine. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+SoPINE link:
+https://www.pine64.org/?page_id=1491
+
+Wiki link:
+https://openedev.amarulasolutions.com/display/ODWIKI/SoPine
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+How to build
+============
+
+    $ make pine64_sopine_defconfig
+
+    $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+  $ sudo sync
+
+Insert the micro SDcard in your SoPine and power it up. The console
+is on the serial line, 115200 8N1.

47 lines not on this page · raw message

index a690b17..9e566de 100644
@@ -119,6 +119,7 @@ freescale_imx6ulevk_defconfig: *defconfig
 freescale_imx7dsabresd_defconfig: *defconfig
 freescale_mpc8315erdb_defconfig: *defconfig
 freescale_p1010rdb_pa_defconfig: *defconfig
+friendlyarm_nanopi_a64_defconfig: *defconfig
 galileo_defconfig: *defconfig
 gdb_bfin_bf512_defconfig: *defconfig
 grinn_chiliboard_defconfig: *defconfig

index 106d793..cae3730 100644
@@ -728,9 +728,11 @@ F:	package/keepalived/
 N:	Jagan Teki <[email protected]>
 F:	board/bananapi/
 F:	board/engicam/
+F:	board/friendlyarm/nanopi-a64/
 F:	board/pine64/
 F:	configs/bananapi_m1_defconfig
 F:	configs/bananapi_m64_defconfig
+F:	configs/friendlyarm_nanopi_a64_defconfig
 F:	configs/pine64_defconfig
 F:	configs/pine64_sopine_defconfig
 F:	configs/engicam_imx6qdl_icore_defconfig

new file mode 100644
index 0000000..446bd85
@@ -0,0 +1,6 @@
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r Image
+fatload mmc 0 $fdt_addr_r sun50i-a64-nanopi-a64.dtb
+
+booti $kernel_addr_r - $fdt_addr_r

new file mode 100644
index 0000000..edfb52d
@@ -0,0 +1,38 @@
+image boot.vfat {
+	vfat {
+		files = {
+			"Image",
+			"sun50i-a64-nanopi-a64.dtb",
+			"boot.scr"
+		}
+	}
+	size = 64M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition spl {
+		in-partition-table = "no"
+		image = "sunxi-spl.bin"
+		offset = 8192
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot.itb"
+		offset = 40K
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100644
index 0000000..b19bc65
@@ -0,0 +1,3 @@
+CONFIG_SUNXI_RSB=y
+CONFIG_MFD_AXP20X_RSB=y
+CONFIG_REGULATOR_AXP20X=y

41 lines not on this page · raw message

176 lines not on this page · raw message

254 lines not on this page · raw message

new file mode 100644
index 0000000..88c4e66
@@ -0,0 +1,37 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the Nanopi A64. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+Nanopi A64 link:
+http://nanopi.io/nanopi-a64.html
+
+Wiki link:
+https://openedev.amarulasolutions.com/display/ODWIKI/FriendlyARM+Nanopi+A64
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+How to build
+============
+
+    $ make friendlyarm_nanopi_a64_defconfig
+    $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+  $ sudo sync
+
+Insert the micro SDcard in your Nanopi A64 and power it up. The console
+is on the serial line, 115200 8N1.

51 lines not on this page · raw message

index 9e566de..f09c8da 100644
@@ -120,6 +120,7 @@ freescale_imx7dsabresd_defconfig: *defconfig
 freescale_mpc8315erdb_defconfig: *defconfig
 freescale_p1010rdb_pa_defconfig: *defconfig
 friendlyarm_nanopi_a64_defconfig: *defconfig
+friendlyarm_nanopi_neo2_defconfig: *defconfig
 galileo_defconfig: *defconfig
 gdb_bfin_bf512_defconfig: *defconfig
 grinn_chiliboard_defconfig: *defconfig

index cae3730..1832310 100644
@@ -729,10 +729,12 @@ N:	Jagan Teki <[email protected]>
 F:	board/bananapi/
 F:	board/engicam/
 F:	board/friendlyarm/nanopi-a64/
+F:	board/friendlyarm/nanopi-neo2/
 F:	board/pine64/
 F:	configs/bananapi_m1_defconfig
 F:	configs/bananapi_m64_defconfig
 F:	configs/friendlyarm_nanopi_a64_defconfig
+F:	configs/friendlyarm_nanopi_neo2_defconfig
 F:	configs/pine64_defconfig
 F:	configs/pine64_sopine_defconfig
 F:	configs/engicam_imx6qdl_icore_defconfig

new file mode 100644
index 0000000..9a39f4a
@@ -0,0 +1,6 @@
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r Image
+fatload mmc 0 $fdt_addr_r sun50i-h5-nanopi-neo2.dtb
+
+booti $kernel_addr_r - $fdt_addr_r

new file mode 100644
index 0000000..a1156a4
@@ -0,0 +1,38 @@
+image boot.vfat {
+	vfat {
+		files = {
+			"Image",
+			"sun50i-h5-nanopi-neo2.dtb",
+			"boot.scr"
+		}
+	}
+	size = 64M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition spl {
+		in-partition-table = "no"
+		image = "sunxi-spl.bin"
+		offset = 8192
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot.itb"
+		offset = 40K
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100644
index 0000000..0f445e2
@@ -0,0 +1,37 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the Nanopi NEO2. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+Nanopi NEO2 link:
+http://nanopi.io/nanopi-neo2.html
+
+Wiki link:
+https://openedev.amarulasolutions.com/display/ODWIKI/FriendlyARM+NanoPi+NEO2
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+How to build
+============
+
+    $ make friendlyarm_nanopi_neo2_defconfig
+    $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+  $ sudo sync
+
+Insert the micro SDcard in your Nanopi NEO2 and power it up. The console
+is on the serial line, 115200 8N1.

47 lines not on this page · raw message

index f09c8da..8c6d2b3 100644
@@ -154,6 +154,7 @@ olimex_a20_olinuxino_lime2_defconfig: *defconfig
 olimex_a20_olinuxino_lime_defconfig: *defconfig
 olimex_a20_olinuxino_lime_mali_defconfig: *defconfig
 olimex_a20_olinuxino_micro_defconfig: *defconfig
+olimex_a64_olinuxino_defconfig: *defconfig
 olimex_imx233_olinuxino_defconfig: *defconfig
 openblocks_a6_defconfig: *defconfig
 orangepi_one_defconfig: *defconfig

index 1832310..1ae83f2 100644
@@ -730,11 +730,13 @@ F:	board/bananapi/
 F:	board/engicam/
 F:	board/friendlyarm/nanopi-a64/
 F:	board/friendlyarm/nanopi-neo2/
+F:	board/olimex/a64-olinuxino/
 F:	board/pine64/
 F:	configs/bananapi_m1_defconfig
 F:	configs/bananapi_m64_defconfig
 F:	configs/friendlyarm_nanopi_a64_defconfig
 F:	configs/friendlyarm_nanopi_neo2_defconfig
+F:	configs/olimex_a64_olinuxino_defconfig
 F:	configs/pine64_defconfig
 F:	configs/pine64_sopine_defconfig
 F:	configs/engicam_imx6qdl_icore_defconfig

new file mode 100644
index 0000000..28ed6d9
@@ -0,0 +1,6 @@
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r Image
+fatload mmc 0 $fdt_addr_r sun50i-a64-olinuxino.dtb
+
+booti $kernel_addr_r - $fdt_addr_r

new file mode 100644
index 0000000..a365bfe
@@ -0,0 +1,38 @@
+image boot.vfat {
+	vfat {
+		files = {
+			"Image",
+			"sun50i-a64-olinuxino.dtb",
+			"boot.scr"
+		}
+	}
+	size = 64M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition spl {
+		in-partition-table = "no"
+		image = "sunxi-spl.bin"
+		offset = 8192
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot.itb"
+		offset = 40K
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100644
index 0000000..b19bc65
@@ -0,0 +1,3 @@
+CONFIG_SUNXI_RSB=y
+CONFIG_MFD_AXP20X_RSB=y
+CONFIG_REGULATOR_AXP20X=y

41 lines not on this page · raw message

176 lines not on this page · raw message

244 lines not on this page · raw message

new file mode 100644
index 0000000..342bdc7
@@ -0,0 +1,37 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the A64-OLinuXino. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+A64-OLinuXino link:
+https://www.olimex.com/Products/OLinuXino/A64/
+
+Wiki link:
+https://openedev.amarulasolutions.com/display/ODWIKI/Olimex+A64-Olinuxino
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+How to build
+============
+
+    $ make olimex_a64_olinuxino_defconfig
+    $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+  $ sudo sync
+
+Insert the micro SDcard in your A64-OLinuXino and power it up. The console
+is on the serial line, 115200 8N1.

51 lines not on this page · raw message

index 8c6d2b3..8cf4ae2 100644
@@ -160,6 +160,7 @@ openblocks_a6_defconfig: *defconfig
 orangepi_one_defconfig: *defconfig
 orangepi_pc_defconfig: *defconfig
 orangepi_plus_defconfig: *defconfig
+orangepi_win_defconfig: *defconfig
 orangepi_zero_defconfig: *defconfig
 pandaboard_defconfig: *defconfig
 pc_x86_64_bios_defconfig: *defconfig

index 1ae83f2..123e444 100644
@@ -731,12 +731,14 @@ F:	board/engicam/
 F:	board/friendlyarm/nanopi-a64/
 F:	board/friendlyarm/nanopi-neo2/
 F:	board/olimex/a64-olinuxino/
+F:	board/orangepi/orangepi-win/
 F:	board/pine64/
 F:	configs/bananapi_m1_defconfig
 F:	configs/bananapi_m64_defconfig
 F:	configs/friendlyarm_nanopi_a64_defconfig
 F:	configs/friendlyarm_nanopi_neo2_defconfig
 F:	configs/olimex_a64_olinuxino_defconfig
+F:	configs/orangepi_win_defconfig
 F:	configs/pine64_defconfig
 F:	configs/pine64_sopine_defconfig
 F:	configs/engicam_imx6qdl_icore_defconfig

new file mode 100644
index 0000000..2ddb769
@@ -0,0 +1,6 @@
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r Image
+fatload mmc 0 $fdt_addr_r sun50i-a64-orangepi-win.dtb
+
+booti $kernel_addr_r - $fdt_addr_r

new file mode 100644
index 0000000..36955d3
@@ -0,0 +1,38 @@
+image boot.vfat {
+	vfat {
+		files = {
+			"Image",
+			"sun50i-a64-orangepi-win.dtb",
+			"boot.scr"
+		}
+	}
+	size = 64M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition spl {
+		in-partition-table = "no"
+		image = "sunxi-spl.bin"
+		offset = 8192
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot.itb"
+		offset = 40K
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100644
index 0000000..93adddd
@@ -0,0 +1,37 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the Orangepi Win/Win Plus. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+Orangepi Win/Win Plus link:
+http://www.orangepi.org/OrangePiWin_WinPlus/
+
+Wiki link:
+https://openedev.amarulasolutions.com/display/ODWIKI/Orangepi+Win
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+How to build
+============
+
+    $ make orangepi_win_defconfig
+    $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+  $ sudo sync
+
+Insert the micro SDcard in your Orangepi Win/Win Plus and power it up. The console
+is on the serial line, 115200 8N1.

47 lines not on this page · raw message

index 8cf4ae2..ef4fa10 100644
@@ -160,6 +160,7 @@ openblocks_a6_defconfig: *defconfig
 orangepi_one_defconfig: *defconfig
 orangepi_pc_defconfig: *defconfig
 orangepi_plus_defconfig: *defconfig
+orangepi_prime_defconfig: *defconfig
 orangepi_win_defconfig: *defconfig
 orangepi_zero_defconfig: *defconfig
 pandaboard_defconfig: *defconfig

index 123e444..40b9fd7 100644
@@ -731,6 +731,7 @@ F:	board/engicam/
 F:	board/friendlyarm/nanopi-a64/
 F:	board/friendlyarm/nanopi-neo2/
 F:	board/olimex/a64-olinuxino/
+F:	board/orangepi/orangepi-prime/
 F:	board/orangepi/orangepi-win/
 F:	board/pine64/
 F:	configs/bananapi_m1_defconfig

@@ -738,6 +739,7 @@ F:	configs/bananapi_m64_defconfig
 F:	configs/friendlyarm_nanopi_a64_defconfig
 F:	configs/friendlyarm_nanopi_neo2_defconfig
 F:	configs/olimex_a64_olinuxino_defconfig
+F:	configs/orangepi_prime_defconfig
 F:	configs/orangepi_win_defconfig
 F:	configs/pine64_defconfig
 F:	configs/pine64_sopine_defconfig

new file mode 100644
index 0000000..3488788
@@ -0,0 +1,6 @@
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r Image
+fatload mmc 0 $fdt_addr_r sun50i-h5-orangepi-prime.dtb
+
+booti $kernel_addr_r - $fdt_addr_r

new file mode 100644
index 0000000..b973b02
@@ -0,0 +1,38 @@
+image boot.vfat {
+	vfat {
+		files = {
+			"Image",
+			"sun50i-h5-orangepi-prime.dtb",
+			"boot.scr"
+		}
+	}
+	size = 64M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition spl {
+		in-partition-table = "no"
+		image = "sunxi-spl.bin"
+		offset = 8192
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot.itb"
+		offset = 40K
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100644
index 0000000..5811884
@@ -0,0 +1,37 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the Orangepi Prime. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+Orangepi Prime link:
+http://www.orangepi.org/OrangePiPrime/
+
+Wiki link:
+https://openedev.amarulasolutions.com/display/ODWIKI/Orangepi+Prime
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+How to build
+============
+
+    $ make orangepi_prime_defconfig
+    $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+  $ sudo sync
+
+Insert the micro SDcard in your Orangepi Prime and power it up. The console
+is on the serial line, 115200 8N1.

47 lines not on this page · raw message

index ef4fa10..630cab1 100644
@@ -163,6 +163,7 @@ orangepi_plus_defconfig: *defconfig
 orangepi_prime_defconfig: *defconfig
 orangepi_win_defconfig: *defconfig
 orangepi_zero_defconfig: *defconfig
+orangepi_zero_plus2_defconfig: *defconfig
 pandaboard_defconfig: *defconfig
 pc_x86_64_bios_defconfig: *defconfig
 pc_x86_64_efi_defconfig: *defconfig

index 40b9fd7..f683c25 100644
@@ -733,6 +733,7 @@ F:	board/friendlyarm/nanopi-neo2/
 F:	board/olimex/a64-olinuxino/
 F:	board/orangepi/orangepi-prime/
 F:	board/orangepi/orangepi-win/
+F:	board/orangepi/orangepi-zero-plus2/
 F:	board/pine64/
 F:	configs/bananapi_m1_defconfig
 F:	configs/bananapi_m64_defconfig

@@ -741,6 +742,7 @@ F:	configs/friendlyarm_nanopi_neo2_defconfig
 F:	configs/olimex_a64_olinuxino_defconfig
 F:	configs/orangepi_prime_defconfig
 F:	configs/orangepi_win_defconfig
+F:	configs/orangepi_zero_plus2_defconfig
 F:	configs/pine64_defconfig
 F:	configs/pine64_sopine_defconfig
 F:	configs/engicam_imx6qdl_icore_defconfig

new file mode 100644
index 0000000..4772a9b
@@ -0,0 +1,6 @@
+setenv bootargs console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait
+
+fatload mmc 0 $kernel_addr_r Image
+fatload mmc 0 $fdt_addr_r sun50i-h5-orangepi-zero-plus2.dtb
+
+booti $kernel_addr_r - $fdt_addr_r

new file mode 100644
index 0000000..0fe219e
@@ -0,0 +1,38 @@
+image boot.vfat {
+	vfat {
+		files = {
+			"Image",
+			"sun50i-h5-orangepi-zero-plus2.dtb",
+			"boot.scr"
+		}
+	}
+	size = 64M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition spl {
+		in-partition-table = "no"
+		image = "sunxi-spl.bin"
+		offset = 8192
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot.itb"
+		offset = 40K
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100644
index 0000000..322ba0e
@@ -0,0 +1,37 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the Orangepi Zero Plus2. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+Orangepi Zero Plus2 link:
+http://www.orangepi.org/OrangePiZeroPlus2/
+
+Wiki link:
+https://openedev.amarulasolutions.com/display/ODWIKI/Orangepi+Zero+Plus2
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+How to build
+============
+
+    $ make orangepi_zero_plus2_defconfig
+    $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+  $ sudo sync
+
+Insert the micro SDcard in your Orangepi Zero Plus2 and power it up. The console
+is on the serial line, 115200 8N1.

47 lines not on this page · raw message