uboot: Use BR2_TARGET_UBOOT_SPL_NAME for TPL name

index 8215912..70e2bfd 100644
@@ -334,13 +334,14 @@ config BR2_TARGET_UBOOT_SPL
 	  into DDR.
 
 config BR2_TARGET_UBOOT_SPL_NAME
-	string "U-Boot SPL binary image name"
+	string "U-Boot SPL/TPL binary image name(s)"
 	default "spl/u-boot-spl.bin"
 	depends on BR2_TARGET_UBOOT_SPL
 	help
-	  A space-separated list of SPL binaries, generated during
-	  u-boot build. For most platform it is spl/u-boot-spl.bin but
-	  not always. It is MLO on OMAP and SPL on i.MX6 for example.
+	  A space-separated list of SPL/TPL binaries, generated during
+	  u-boot build. For most platform SPL name is spl/u-boot-spl.bin
+	  and TPL name is tpl/u-boot-tpl.bin but not always. SPL name is
+	  MLO on OMAP and SPL on i.MX6 for example.
 
 config BR2_TARGET_UBOOT_ZYNQ_IMAGE
 	bool "Generate image for Xilinx Zynq"

index 0dddb22..542663a 100644
@@ -62,6 +62,7 @@ acmesystems_aria_g25_128mb_defconfig: *defconfig
 acmesystems_aria_g25_256mb_defconfig: *defconfig
 acmesystems_arietta_g25_128mb_defconfig: *defconfig
 acmesystems_arietta_g25_256mb_defconfig: *defconfig
+amarula_vyasa_rk3288_defconfig: *defconfig
 arcturus_ucp1020_defconfig: *defconfig
 arm_foundationv8_defconfig: *defconfig
 arm_juno_defconfig: *defconfig

index c39348a..0db11e1 100644
@@ -745,8 +745,10 @@ N:	Ilias Apalodimas <[email protected]>
 F:	package/keepalived/
 
 N:	Jagan Teki <[email protected]>
+F:	board/amarula/
 F:	board/bananapi/
 F:	board/engicam/
+F:	configs/amarula_vyasa_rk3288_defconfig
 F:	configs/bananapi_m1_defconfig
 F:	configs/engicam_imx6qdl_icore_defconfig
 F:	configs/engicam_imx6qdl_icore_qt5_defconfig

new file mode 100644
index 0000000..a8fcc35
@@ -0,0 +1,4 @@
+label Vyasa linux-next
+  kernel /boot/uImage
+  devicetree /boot/rk3288-vyasa.dtb
+  append console=ttyS2,115200n8 root=/dev/mmcblk0p1 rootwait

new file mode 100644
index 0000000..fa41de3
@@ -0,0 +1,21 @@
+image sdcard.img {
+	hdimage {
+	}
+
+	partition u-boot-tpl-spl-dtb {
+		in-partition-table = "no"
+		image = "u-boot-tpl-spl-dtb.img"
+		offset = 32K
+	}
+
+	partition u-boot-dtb {
+		in-partition-table = "no"
+		image = "u-boot-dtb.img"
+		offset = 8M
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100644
index 0000000..dd458c7
@@ -0,0 +1,3 @@
+# Currently kernel mainline exhibits issues when running rockchip gmac
+# on the board, so enable it as loadable module and insert it later
+CONFIG_DWMAC_ROCKCHIP=m

new file mode 100755
index 0000000..ffbbcde
@@ -0,0 +1,9 @@
+#!/bin/sh
+
+MKIMAGE=$HOST_DIR/bin/mkimage
+BOARD_DIR="$(dirname $0)"
+
+$MKIMAGE -n rk3288 -T rksd -d $BINARIES_DIR/u-boot-tpl.bin $BINARIES_DIR/u-boot-tpl.img
+cat $BINARIES_DIR/u-boot-tpl.img $BINARIES_DIR/u-boot-spl-dtb.bin > $BINARIES_DIR/u-boot-tpl-spl-dtb.img
+
+install -m 0644 -D $BOARD_DIR/extlinux.conf $TARGET_DIR/boot/extlinux/extlinux.conf

new file mode 100644
index 0000000..b95889e
@@ -0,0 +1,31 @@
+Vyasa RK3288
+============
+
+Vyasa is RK3288 based Single board computer with fully supported opensource software.
+
+https://openedev.amarulasolutions.com/display/ODWIKI/Vyasa+RK3288
+
+How to build it
+===============
+
+  $ make amarula_vyasa_rk3288_defconfig
+
+Then you can edit the build options using
+
+  $ make menuconfig
+
+Compile all and build rootfs image:
+
+  $ make
+
+Prepare your SDCard
+===================
+
+Buildroot generates a ready-to-use SD card image that you can flash directly to
+the card. The image will be in output/images/sdcard.img.
+You can write this image directly to an SD card device (i.e. /dev/xxx):
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/xxx
+  $ sudo sync
+
+Finally, you can insert the SD card to the Vyasa RK3288 board, close J4 and boot it.

59 lines not on this page · raw message

index 542663a..a9c0202 100644
@@ -69,6 +69,7 @@ arm_juno_defconfig: *defconfig
 armadeus_apf27_defconfig: *defconfig
 armadeus_apf28_defconfig: *defconfig
 armadeus_apf51_defconfig: *defconfig
+asus_tinker_rk3288_defconfig: *defconfig
 at91sam9260eknf_defconfig: *defconfig
 at91sam9g20dfc_defconfig: *defconfig
 at91sam9g45m10ek_defconfig: *defconfig

index 0db11e1..053d5e4 100644
@@ -746,9 +746,11 @@ F:	package/keepalived/
 
 N:	Jagan Teki <[email protected]>
 F:	board/amarula/
+F:	board/asus/
 F:	board/bananapi/
 F:	board/engicam/
 F:	configs/amarula_vyasa_rk3288_defconfig
+F:	configs/asus_tinker_rk3288_defconfig
 F:	configs/bananapi_m1_defconfig
 F:	configs/engicam_imx6qdl_icore_defconfig
 F:	configs/engicam_imx6qdl_icore_qt5_defconfig

new file mode 100644
index 0000000..136af0d
@@ -0,0 +1,4 @@
+label Tinker linux-next
+  kernel /boot/uImage
+  devicetree /boot/rk3288-tinker.dtb
+  append console=ttyS2,115200n8 root=/dev/mmcblk0p1 rootwait

new file mode 100644
index 0000000..a4b1e8d
@@ -0,0 +1,15 @@
+image sdcard.img {
+	hdimage {
+	}
+
+	partition u-boot-spl-dtb {
+		in-partition-table = "no"
+		image = "u-boot-spl-dtb.img"
+		offset = 32K
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

new file mode 100755
index 0000000..8108ed8
@@ -0,0 +1,9 @@
+#!/bin/sh
+
+MKIMAGE=$HOST_DIR/bin/mkimage
+BOARD_DIR="$(dirname $0)"
+
+$MKIMAGE -n rk3288 -T rksd -d $BINARIES_DIR/u-boot-spl-dtb.bin $BINARIES_DIR/u-boot-spl-dtb.img
+cat $BINARIES_DIR/u-boot-dtb.bin >> $BINARIES_DIR/u-boot-spl-dtb.img
+
+install -m 0644 -D $BOARD_DIR/extlinux.conf $TARGET_DIR/boot/extlinux/extlinux.conf

new file mode 100644
index 0000000..7372d29
@@ -0,0 +1,37 @@
+Tinker RK3288
+=============
+
+Tinker Board is a Single Board Computer (SBC) in an ultra-small form
+factor that offers class-leading performance while leveraging outstanding
+mechanical compatibility.
+
+Tinker link:
+https://www.asus.com/in/Single-Board-Computer/Tinker-Board/
+
+Wiki link:
+https://openedev.amarulasolutions.com/display/ODWIKI/Tinker+RK3288
+
+How to build it
+===============
+
+  $ make asus_tinker_rk3288_defconfig
+
+Then you can edit the build options using
+
+  $ make menuconfig
+
+Compile all and build rootfs image:
+
+  $ make
+
+Prepare your SDCard
+===================
+
+Buildroot generates a ready-to-use SD card image that you can flash directly to
+the card. The image will be in output/images/sdcard.img.
+You can write this image directly to an SD card device (i.e. /dev/xxx):
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/xxx
+  $ sudo sync
+
+Finally, you can insert the SD card to the Tinker RK3288 board and boot it.

55 lines not on this page · raw message