add VLAN support to DSA MT7530
Subsystems (5)
cover add VLAN support to DSA MT7530
From: Sean Wang <[email protected]>
The patchset extends DSA MT7530 to VLAN support through filling required callbacks in patch 1 and merging the special tag with VLAN tag in patch 2 for allowing that the hardware can handle these packets with VID from the CPU port.
Sean Wang (3):
net: dsa: mediatek: add VLAN support for MT7530
net: dsa: mediatek: combine MediaTek tag with VLAN tag
net: dsa: mediatek: update MAINTAINERS entry with MediaTek switch
driver
MAINTAINERS | 7 ++ drivers/net/dsa/mt7530.c | 292 ++++++++++++++++++++++++++++++++++++++++++++++- drivers/net/dsa/mt7530.h | 83 +++++++++++++- net/dsa/tag_mtk.c | 38 ++++-- 4 files changed, 404 insertions(+), 16 deletions(-)
Signature · 1 line
2.7.4
PATCH 1/3 net: dsa: mediatek: add VLAN support for MT7530
From: Sean Wang <[email protected]>
MT7530 can treat each port as either VLAN-unware port or VLAN-ware port through the implementation of port matrix mode or port security mode on the ingress port, respectively. On one hand, Each port has been acting as the VLAN-unware one whenever the device is created in the initial or certain port joins or leaves into/from the bridge at the runtime. On the other hand, the patch just filling the required callbacks for VLAN operations is achieved via extending the port to be into port security mode when the port is configured as VLAN-ware port. Which mode can make the port be able to recognize VID from incoming packets and look up VLAN table to validate and judge which port it should be going to. And the range for VID from 1 to 4094 is valid for the hardware.
--- drivers/net/dsa/mt7530.c | 292 ++++++++++++++++++++++++++++++++++++++++++++++- drivers/net/dsa/mt7530.h | 83 +++++++++++++- 2 files changed, 368 insertions(+), 7 deletions(-)
drivers/net/dsa/mt7530.c +291 -1
@@ -805,6 +805,69 @@ mt7530_port_bridge_join(struct dsa_switch *ds, int port, }static void +mt7530_port_set_vlan_unware (struct dsa_switch *ds,int port) +{ +struct mt7530_priv *priv = ds->priv; +int i; +bool all_user_ports_removed = true; + +/* When a port is removed from the bridge, the port would be set up +* back to the default as is at initial boot which is a VLAN-unware +* port. +*/ +mt7530_rmw (priv,MT7530_PCR_P (port),PCR_PORT_VLAN_MASK , +MT7530_PORT_MATRIX_MODE ); +mt7530_rmw (priv,MT7530_PVC_P (port),VLAN_ATTR_MASK , +VLAN_ATTR (MT7530_VLAN_TRANSPARENT )); + + priv->ports[port].vlan_filtering = false; + +for (i =0 ; i <MT7530_NUM_PORTS ; i++) { +if (dsa_is_user_port (ds, i) && + priv->ports[i].vlan_filtering) { + all_user_ports_removed = false; +break ; + } + } + +/* CPU port also does the same thing until all user ports belonging to +* the CPU port get out of VLAN filtering mode. +*/ +if (all_user_ports_removed) { +mt7530_write (priv,MT7530_PCR_P (MT7530_CPU_PORT ), +PCR_MATRIX (dsa_user_ports (priv->ds))); +mt7530_write (priv,MT7530_PVC_P (MT7530_CPU_PORT ), +PORT_SPEC_TAG ); + } +} + +static void +mt7530_port_set_vlan_ware (struct dsa_switch *ds,int port) +{ +struct mt7530_priv *priv = ds->priv; + +/* The real fabric path would be decided on the membership in the +* entry of VLAN table. PCR_MATRIX set up here with ALL_MEMBERS +* means potential VLAN can be consisting of certain subset of all +* ports. +*/ +mt7530_rmw (priv,MT7530_PCR_P (port), +PCR_MATRIX_MASK ,PCR_MATRIX (MT7530_ALL_MEMBERS )); + +/* Trapped into security mode allows packet forwarding through VLAN +* table lookup. +*/ +mt7530_rmw (priv,MT7530_PCR_P (port),PCR_PORT_VLAN_MASK , +MT7530_PORT_SECURITY_MODE ); + +/* Set the port as a user port which is to be able to recognize VID +* from incoming packets before fetching entry within the VLAN table. +*/ +mt7530_rmw (priv,MT7530_PVC_P (port),VLAN_ATTR_MASK , +VLAN_ATTR (MT7530_VLAN_USER )); +} + +static void mt7530_port_bridge_leave (struct dsa_switch *ds,int port,struct net_device *bridge) {
@@ -817,8 +880,11 @@ mt7530_port_bridge_leave(struct dsa_switch *ds, int port,/* Remove this port from the port matrix of the other ports * in the same bridge. If the port is disabled, port matrix * is kept and not being setup until the port becomes enabled. +* And the other port's port matrix cannot be broken when the +* other port is still a VLAN-ware port. */ -if (dsa_is_user_port (ds, i) && i != port) { +if (!priv->ports[i].vlan_filtering && +dsa_is_user_port (ds, i) && i != port) {if (dsa_to_port (ds, i)->bridge_dev != bridge)continue ;if (priv->ports[i].enable)
@@ -836,6 +902,8 @@ mt7530_port_bridge_leave(struct dsa_switch *ds, int port, PCR_MATRIX(BIT(MT7530_CPU_PORT))); priv->ports[port].pm =PCR_MATRIX (BIT (MT7530_CPU_PORT )); +mt7530_port_set_vlan_unware (ds, port); +mutex_unlock (&priv->reg_mutex); }
@@ -906,6 +974,224 @@ mt7530_port_fdb_dump(struct dsa_switch *ds, int port,return 0 ; } +static int +mt7530_vlan_cmd (struct mt7530_priv *priv,enum mt7530_vlan_cmd cmd,u16 vid) +{ +u32 val; +int ret; +struct mt7530_dummy_poll p; + + val =VTCR_BUSY |VTCR_FUNC (cmd) | vid; +mt7530_write (priv,MT7530_VTCR , val); + +INIT_MT7530_DUMMY_POLL (&p, priv,MT7530_VTCR ); + ret =readx_poll_timeout (_mt7530_read, &p, val, + !(val &VTCR_BUSY ),20 ,20000 ); +if (ret <0 ) { +dev_err (priv->dev,"poll timeout\n" ); +return ret; + } + + val =mt7530_read (priv,MT7530_VTCR ); +if (val &VTCR_INVALID ) { +dev_err (priv->dev,"read VTCR invalid\n" ); +return -EINVAL ; + } + +return 0 ; +} + +static int +mt7530_port_vlan_filtering (struct dsa_switch *ds,int port, +bool vlan_filtering) +{ +struct mt7530_priv *priv = ds->priv; + + priv->ports[port].vlan_filtering = vlan_filtering; + +return 0 ; +} + +static int +mt7530_port_vlan_prepare (struct dsa_switch *ds,int port, +const struct switchdev_obj_port_vlan *vlan, +struct switchdev_trans *trans) +{ +struct mt7530_priv *priv = ds->priv; + +/* The port is being kept as VLAN-unware port when bridge is set up +* with vlan_filtering not being set, Otherwise, the port and the +* corresponding CPU port is required the setup for becoming a +* VLAN-ware port. +*/ +if (!priv->ports[port].vlan_filtering) +return 0 ; + +mt7530_port_set_vlan_ware (ds, port); +mt7530_port_set_vlan_ware (ds,MT7530_CPU_PORT ); + +return 0 ; +} + +static void +mt7530_hw_vlan_add (struct mt7530_priv *priv, +struct mt7530_hw_vlan_entry *entry) +{ +u32 val; +u8 new_members; + + new_members = entry->old_members |BIT (entry->port) | +BIT (MT7530_CPU_PORT ); + +/* Validate the entry with independent learning, create egress tag per +* VLAN and joining the port as one of the port members. +*/ + val =IVL_MAC |VTAG_EN |PORT_MEM (new_members) |VLAN_VALID ; +mt7530_write (priv,MT7530_VAWD1 , val); + +/* Decide whether adding tag or not for those outgoing packets from the +* port inside the VLAN. +*/ + val = entry->untagged ?MT7530_VLAN_EGRESS_UNTAG : +MT7530_VLAN_EGRESS_TAG ; +mt7530_rmw (priv,MT7530_VAWD2 , +ETAG_CTRL_P_MASK (entry->port), +ETAG_CTRL_P (entry->port, val)); + +/* CPU port is always taken as a tagged port for serving more than one +* VLANs across and also being applied with egress type stack mode for +* that VLAN tags would be appended after hardware special tag used as +* DSA tag. +*/ +mt7530_rmw (priv,MT7530_VAWD2 , +ETAG_CTRL_P_MASK (MT7530_CPU_PORT ), +ETAG_CTRL_P (MT7530_CPU_PORT , +MT7530_VLAN_EGRESS_STACK )); +} + +static void +mt7530_hw_vlan_del (struct mt7530_priv *priv, +struct mt7530_hw_vlan_entry *entry) +{ +u32 val; +u8 new_members; + + new_members = entry->old_members & ~BIT (entry->port); + + val =mt7530_read (priv,MT7530_VAWD1 ); +if (!(val &VLAN_VALID )) { +dev_err (priv->dev, +"Cannot be deleted due to invalid entry\n" ); +return ; + } + +/* If certain member apart from CPU port is still alive in the VLAN, +* the entry would be kept valid. Otherwise, the entry is got to be +* disabled. +*/ +if (new_members && new_members !=BIT (MT7530_CPU_PORT )) { + val =IVL_MAC |VTAG_EN |PORT_MEM (new_members) | +VLAN_VALID ; +mt7530_write (priv,MT7530_VAWD1 , val); + }else { +mt7530_write (priv,MT7530_VAWD1 ,0 ); +mt7530_write (priv,MT7530_VAWD2 ,0 ); + } +} + +static void +mt7530_hw_vlan_update (struct mt7530_priv *priv,u16 vid, +struct mt7530_hw_vlan_entry *entry, +mt7530_vlan_op vlan_op) +{ +u32 val; + +/* Fetch entry */ +mt7530_vlan_cmd (priv,MT7530_VTCR_RD_VID , vid); + + val =mt7530_read (priv,MT7530_VAWD1 ); + + entry->old_members = (val >>PORT_MEM_SHFT ) &PORT_MEM_MASK ; + +/* Manipulate entry */ +vlan_op (priv, entry); + +/* Flush result to hardware */ +mt7530_vlan_cmd (priv,MT7530_VTCR_WR_VID , vid); +} + +static void +mt7530_port_vlan_add (struct dsa_switch *ds,int port, +const struct switchdev_obj_port_vlan *vlan, +struct switchdev_trans *trans) +{ +struct mt7530_priv *priv = ds->priv; +struct mt7530_hw_vlan_entry new_entry; +u16 vid; +bool untagged = vlan->flags &BRIDGE_VLAN_INFO_UNTAGGED ; +bool pvid = vlan->flags &BRIDGE_VLAN_INFO_PVID ; +int ret; + +/* The port is kept as VLAN-unware if bridge with vlan_filtering not +* being set. +*/ +if (!priv->ports[port].vlan_filtering) +return ; + +mutex_lock (&priv->reg_mutex); + +for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) { +INIT_MT7530_HW_ENTRY (&new_entry, port, untagged); +mt7530_hw_vlan_update (priv, vid, &new_entry, + mt7530_hw_vlan_add); + } + +if (pvid) { +mt7530_rmw (priv,MT7530_PPBV1_P (port),G0_PORT_VID_MASK , +G0_PORT_VID (vlan->vid_end)); + priv->ports[port].pvid = vlan->vid_end; + } + +mutex_unlock (&priv->reg_mutex); +} + +static int +mt7530_port_vlan_del (struct dsa_switch *ds,int port, +const struct switchdev_obj_port_vlan *vlan) +{ +struct mt7530_priv *priv = ds->priv; +struct mt7530_hw_vlan_entry target_entry; +u16 vid, pvid; + +/* The port is kept as VLAN-unware if bridge with vlan_filtering not +* being set. +*/ +if (!priv->ports[port].vlan_filtering) +return 0 ; + +mutex_lock (&priv->reg_mutex); + + pvid = priv->ports[port].pvid; +for (vid = vlan->vid_begin; vid <= vlan->vid_end; ++vid) { +INIT_MT7530_HW_ENTRY (&target_entry, port,0 ); +mt7530_hw_vlan_update (priv, vid, &target_entry, + mt7530_hw_vlan_del); + +/* PVID is being restored to the default whenever the PVID port +* is being removed from the VLAN. +*/ +if (pvid == vid) + pvid =G0_PORT_VID_DEF ; + } + +mt7530_rmw (priv,MT7530_PPBV1_P (port),G0_PORT_VID_MASK , pvid); + priv->ports[port].pvid = pvid; + +mutex_unlock (&priv->reg_mutex); + +return 0 ; +} +static enum dsa_tag_protocol mtk_get_tag_protocol (struct dsa_switch *ds,int port) {
@@ -1035,6 +1321,10 @@ static const struct dsa_switch_ops mt7530_switch_ops = { .port_fdb_add = mt7530_port_fdb_add, .port_fdb_del = mt7530_port_fdb_del, .port_fdb_dump = mt7530_port_fdb_dump, + .port_vlan_filtering = mt7530_port_vlan_filtering, + .port_vlan_prepare = mt7530_port_vlan_prepare, + .port_vlan_add = mt7530_port_vlan_add, + .port_vlan_del = mt7530_port_vlan_del, }; static int
drivers/net/dsa/mt7530.h +77 -6
140 lines not on this page · raw message
Signature · 1 line
2.7.4
Andrew Lunn
maintainerRe: [PATCH net-next 1/3] net: dsa: mediatek: add VLAN support for MT7530
drivers/net/dsa/mt7530.c mt7530_port_bridge_join(struct dsa_switch *ds, int port, · line 812
Quoted 6 lines
static void
drivers/net/dsa/mt7530.c +5
-0+mt7530_port_set_vlan_unware(struct dsa_switch *ds, int port) +{ +struct mt7530_priv *priv = ds->priv; +int i; +bool all_user_ports_removed = true;
Hi Sean
Reverse Christmas tree please.
drivers/net/dsa/mt7530.c mt7530_port_fdb_dump(struct dsa_switch *ds, int port, · line 982
Quoted 6 lines
drivers/net/dsa/mt7530.c +6
-0+static int +mt7530_vlan_cmd (struct mt7530_priv *priv,enum mt7530_vlan_cmd cmd,u16 vid) +{ +u32 val; +int ret; +struct mt7530_dummy_poll p;
Here too.
Quoted 7 lines
drivers/net/dsa/mt7530.c +7
-0+static int +mt7530_port_vlan_prepare (struct dsa_switch *ds,int port, +const struct switchdev_obj_port_vlan *vlan, +struct switchdev_trans *trans) +{ +struct mt7530_priv *priv = ds->priv; +
drivers/net/dsa/mt7530.c mt7530_port_fdb_dump(struct dsa_switch *ds, int port, · line 1031
Quoted 10 lines
drivers/net/dsa/mt7530.c +10
-0+/* The port is being kept as VLAN-unware port when bridge is set up +* with vlan_filtering not being set, Otherwise, the port and the +* corresponding CPU port is required the setup for becoming a +* VLAN-ware port. +*/ +if (!priv->ports[port].vlan_filtering) +return 0 ; + +mt7530_port_set_vlan_ware (ds, port); +mt7530_port_set_vlan_ware (ds,MT7530_CPU_PORT );
A prepare function should just validate that it is possible to carry out the operation. It should not change any state. These two last lines probably don't belong here.
drivers/net/dsa/mt7530.c mt7530_port_fdb_dump(struct dsa_switch *ds, int port, · line 1041
Quoted 10 lines
drivers/net/dsa/mt7530.c +10
-0+ +return 0 ; +} + +static void +mt7530_hw_vlan_add (struct mt7530_priv *priv, +struct mt7530_hw_vlan_entry *entry) +{ +u32 val; +u8 new_members;
Reverse Christmas tree. Please check the whole patch.
drivers/net/dsa/mt7530.h struct mt7530_priv { · line 451
Quoted 6 lines
drivers/net/dsa/mt7530.h +6
-0+static inline void INIT_MT7530_HW_ENTRY (struct mt7530_hw_vlan_entry *e, +int port,bool untagged) +{ + e->port = port; + e->untagged = untagged; +}
All CAPITAL letters is for #defines. This is just a normal function. Please use lower case.
Andrew
Re: [PATCH net-next 1/3] net: dsa: mediatek: add VLAN support for MT7530
Hi, Andrew
All sounds reasonable. All will be fixed in the next version.
Sean
Quoted 11 lines · Andrew Lunn
drivers/net/dsa/mt7530.c mt7530_port_bridge_join(struct dsa_switch *ds, int port, · line 812
Quoted 6 lines
static void
drivers/net/dsa/mt7530.c +5
-0+mt7530_port_set_vlan_unware(struct dsa_switch *ds, int port) +{ +struct mt7530_priv *priv = ds->priv; +int i; +bool all_user_ports_removed = true;Hi Sean
Reverse Christmas tree please.
will be fixed
Quoted 9 lines
drivers/net/dsa/mt7530.c mt7530_port_fdb_dump(struct dsa_switch *ds, int port, · line 982
Quoted 6 lines
drivers/net/dsa/mt7530.c +6
-0+static int +mt7530_vlan_cmd (struct mt7530_priv *priv,enum mt7530_vlan_cmd cmd,u16 vid) +{ +u32 val; +int ret; +struct mt7530_dummy_poll p;Here too.
will be fixed
Quoted 13 lines
Quoted 13 lines
drivers/net/dsa/mt7530.c +13
-0+static int +mt7530_port_vlan_prepare (struct dsa_switch *ds,int port, +const struct switchdev_obj_port_vlan *vlan, +struct switchdev_trans *trans) +{ +struct mt7530_priv *priv = ds->priv; + +/* The port is being kept as VLAN-unware port when bridge is set up +* with vlan_filtering not being set, Otherwise, the port and the +* corresponding CPU port is required the setup for becoming a +* VLAN-ware port. +*/ +if (!priv->ports[port].vlan_filtering)
Quoted 9 lines
drivers/net/dsa/mt7530.c mt7530_port_fdb_dump(struct dsa_switch *ds, int port, · line 1031
Quoted 4 lines
drivers/net/dsa/mt7530.c +4
-0+return 0 ; + +mt7530_port_set_vlan_ware (ds, port); +mt7530_port_set_vlan_ware (ds,MT7530_CPU_PORT );A prepare function should just validate that it is possible to carry out the operation. It should not change any state. These two last lines probably don't belong here.
okay, it will be moved into the proper place such as mt7530_port_vlan_filtering
Quoted 4 lines
Quoted 4 lines
drivers/net/dsa/mt7530.c +4
-0+ +return 0 ; +} +
Quoted 9 lines
drivers/net/dsa/mt7530.c mt7530_port_fdb_dump(struct dsa_switch *ds, int port, · line 1041
Quoted 6 lines
drivers/net/dsa/mt7530.c +6
-0+static void +mt7530_hw_vlan_add (struct mt7530_priv *priv, +struct mt7530_hw_vlan_entry *entry) +{ +u32 val; +u8 new_members;Reverse Christmas tree. Please check the whole patch.
will be fixed
Quoted 10 lines
drivers/net/dsa/mt7530.h struct mt7530_priv { · line 451
Quoted 6 lines
drivers/net/dsa/mt7530.h +6
-0+static inline void INIT_MT7530_HW_ENTRY (struct mt7530_hw_vlan_entry *e, +int port,bool untagged) +{ + e->port = port; + e->untagged = untagged; +}All CAPITAL letters is for #defines. This is just a normal function. Please use lower case.
will be fixed
Quoted 2 lines
Andrew
Re: [PATCH net-next 1/3] net: dsa: mediatek: add VLAN support for MT7530
In reply to [email protected]Quoted 3 lines · On 2017-12-07 07:06, [email protected] wrote:
From: Sean Wang <[email protected]>
MT7530 can treat each port as either VLAN-unware port or VLAN-ware port
Shouldn't that be VLAN-unaware/VLAN-aware (in the code as well)?
- Felix
Re: [PATCH net-next 1/3] net: dsa: mediatek: add VLAN support for MT7530
Quoted 8 lines · Felix Fietkau
Quoted 3 lines · On 2017-12-07 07:06, [email protected] wrote:
From: Sean Wang <[email protected]>
MT7530 can treat each port as either VLAN-unware port or VLAN-ware port
Shouldn't that be VLAN-unaware/VLAN-aware (in the code as well)?
- Felix
Hi, Felix
Thank you. It is my misspelling problem. I will fix them all with this including in the code.
Sean
PATCH 2/3 net: dsa: mediatek: combine MediaTek tag with VLAN tag
In reply to [email protected]From: Sean Wang <[email protected]>
In order to let MT7530 switch can recognize well those packets having both special tag and VLAN tag, the information about the special tag should be carried on the existing VLAN tag.
--- net/dsa/tag_mtk.c | 38 +++++++++++++++++++++++++++++--------- 1 file changed, 29 insertions(+), 9 deletions(-)
net/dsa/tag_mtk.c +29 -9
@@ -13,10 +13,13 @@*/ #include <linux/etherdevice.h> +#include <linux/if_vlan.h> #include "dsa_priv.h" #define MTK_HDR_LEN 4 +#define MTK_HDR_XMIT_UNTAGGED 0 +#define MTK_HDR_XMIT_TAGGED_TPID_8100 1#define MTK_HDR_RECV_SOURCE_PORT_MASK GENMASK(2, 0)#define MTK_HDR_XMIT_DP_BIT_MASK GENMASK(5, 0)
@@ -25,20 +28,37 @@ static struct sk_buff *mtk_tag_xmit(struct sk_buff *skb, {struct dsa_port *dp =dsa_slave_to_port (dev);u8 *mtk_tag; +bool is_vlan_skb = true; -if (skb_cow_head (skb,MTK_HDR_LEN ) <0 ) -return NULL ; - -skb_push (skb,MTK_HDR_LEN ); +/* Build the special tag after the MAC Source Address. If VLAN header +* is present, it's required that VLAN header and special tag is +* being combined. Only in this way we can allow the switch can parse +* the both special and VLAN tag at the same time and then look up VLAN +* table with VID. +*/ +if (!skb_vlan_tagged (skb)) { +if (skb_cow_head (skb,MTK_HDR_LEN ) <0 ) +return NULL ; -memmove (skb->data, skb->data +MTK_HDR_LEN ,2 *ETH_ALEN ); +skb_push (skb,MTK_HDR_LEN ); +memmove (skb->data, skb->data +MTK_HDR_LEN ,2 *ETH_ALEN ); + is_vlan_skb = false; + } -/* Build the tag after the MAC Source Address */ mtk_tag = skb->data +2 *ETH_ALEN ; - mtk_tag[0 ] =0 ; + +/* Mark tag attribute on special tag insertion to notify hardware +* whether that's a combined special tag with 802.1Q header. +*/ + mtk_tag[0 ] = is_vlan_skb ?MTK_HDR_XMIT_TAGGED_TPID_8100 : +MTK_HDR_XMIT_UNTAGGED ; mtk_tag[1 ] = (1 << dp->index) &MTK_HDR_XMIT_DP_BIT_MASK ; - mtk_tag[2 ] =0 ; - mtk_tag[3 ] =0 ; + +/* Tag control information is kept for 802.1Q */ +if (!is_vlan_skb) { + mtk_tag[2 ] =0 ; + mtk_tag[3 ] =0 ; + }return skb; }
Signature · 1 line
2.7.4
Andrew Lunn
maintainerRe: [PATCH net-next 2/3] net: dsa: mediatek: combine MediaTek tag with VLAN tag
Quoted 5 lines
net/dsa/tag_mtk.c +1
-0@@ -25,20 +28,37 @@ static struct sk_buff *mtk_tag_xmit(struct sk_buff *skb, {struct dsa_port *dp =dsa_slave_to_port (dev);u8 *mtk_tag; +bool is_vlan_skb = true;
..
Quoted 7 lines
net/dsa/tag_mtk.c +5
-1+/* Mark tag attribute on special tag insertion to notify hardware +* whether that's a combined special tag with 802.1Q header. +*/ + mtk_tag[0 ] = is_vlan_skb ?MTK_HDR_XMIT_TAGGED_TPID_8100 : +MTK_HDR_XMIT_UNTAGGED ; mtk_tag[1 ] = (1 << dp->index) &MTK_HDR_XMIT_DP_BIT_MASK ; - mtk_tag[2 ] =0 ;
net/dsa/tag_mtk.c static struct sk_buff *mtk_tag_xmit(struct sk_buff *skb, · line 64
Quoted 10 lines
net/dsa/tag_mtk.c +6
-1- mtk_tag[3 ] =0 ; + +/* Tag control information is kept for 802.1Q */ +if (!is_vlan_skb) { + mtk_tag[2 ] =0 ; + mtk_tag[3 ] =0 ; + }return skb; }
Hi Sean
So you can mark a packet for egress. What about ingress? How do you know the VLAN/PORT combination for packets the CPU receives? I would of expected a similar change to mtk_tag_rcv().
Andrew
Re: [PATCH net-next 2/3] net: dsa: mediatek: combine MediaTek tag with VLAN tag
Quoted 28 lines · Andrew Lunn
Quoted 5 lines
net/dsa/tag_mtk.c +1
-0@@ -25,20 +28,37 @@ static struct sk_buff *mtk_tag_xmit(struct sk_buff *skb, {struct dsa_port *dp =dsa_slave_to_port (dev);u8 *mtk_tag; +bool is_vlan_skb = true;..
Quoted 7 lines
net/dsa/tag_mtk.c +5
-1+/* Mark tag attribute on special tag insertion to notify hardware +* whether that's a combined special tag with 802.1Q header. +*/ + mtk_tag[0 ] = is_vlan_skb ?MTK_HDR_XMIT_TAGGED_TPID_8100 : +MTK_HDR_XMIT_UNTAGGED ; mtk_tag[1 ] = (1 << dp->index) &MTK_HDR_XMIT_DP_BIT_MASK ; - mtk_tag[2 ] =0 ;net/dsa/tag_mtk.c static struct sk_buff *mtk_tag_xmit(struct sk_buff *skb, · line 64
Quoted 10 lines
net/dsa/tag_mtk.c +6
-1- mtk_tag[3 ] =0 ; + +/* Tag control information is kept for 802.1Q */ +if (!is_vlan_skb) { + mtk_tag[2 ] =0 ; + mtk_tag[3 ] =0 ; + }return skb; }Hi Sean
Quoted 5 lines
So you can mark a packet for egress. What about ingress? How do you know the VLAN/PORT combination for packets the CPU receives? I would of expected a similar change to
mtk_tag_rcv().Andrew
Hi, Andrew
It's unnecessary for extra handling in mtk_tag_rcv() when VLAN tag is present since it is able to put the VLAN tag after the special tag and then follow the existing way to parse.
Sean
Andrew Lunn
maintainerRe: [PATCH net-next 2/3] net: dsa: mediatek: combine MediaTek tag with VLAN tag
Quoted 33 lines · Sean Wang
Quoted 32 lines · Andrew Lunn
Quoted 5 lines
net/dsa/tag_mtk.c +1
-0@@ -25,20 +28,37 @@ static struct sk_buff *mtk_tag_xmit(struct sk_buff *skb, {struct dsa_port *dp =dsa_slave_to_port (dev);u8 *mtk_tag; +bool is_vlan_skb = true;..
Quoted 7 lines
net/dsa/tag_mtk.c +5
-1+/* Mark tag attribute on special tag insertion to notify hardware +* whether that's a combined special tag with 802.1Q header. +*/ + mtk_tag[0 ] = is_vlan_skb ?MTK_HDR_XMIT_TAGGED_TPID_8100 : +MTK_HDR_XMIT_UNTAGGED ; mtk_tag[1 ] = (1 << dp->index) &MTK_HDR_XMIT_DP_BIT_MASK ; - mtk_tag[2 ] =0 ;net/dsa/tag_mtk.c static struct sk_buff *mtk_tag_xmit(struct sk_buff *skb, · line 64
Quoted 10 lines
net/dsa/tag_mtk.c +6
-1- mtk_tag[3 ] =0 ; + +/* Tag control information is kept for 802.1Q */ +if (!is_vlan_skb) { + mtk_tag[2 ] =0 ; + mtk_tag[3 ] =0 ; + }return skb; }Hi Sean
So you can mark a packet for egress. What about ingress? How do you know the VLAN/PORT combination for packets the CPU receives? I would of expected a similar change to
mtk_tag_rcv().
Quoted 7 lines
Quoted 1 line
Andrew
Hi, Andrew
It's unnecessary for extra handling in
mtk_tag_rcv()when VLAN tag is present since it is able to put the VLAN tag after the special tag and then follow the existing way to parse.
Hi Sean
O.K. Please mention this in the commit message. Since it was something i was expecting, it should be documented why it is not needed.
Thanks
Andrew
Re: [PATCH net-next 2/3] net: dsa: mediatek: combine MediaTek tag with VLAN tag
Quoted 42 lines · Andrew Lunn
Quoted 33 lines · Sean Wang
Quoted 32 lines · Andrew Lunn
Quoted 5 lines
net/dsa/tag_mtk.c +1
-0@@ -25,20 +28,37 @@ static struct sk_buff *mtk_tag_xmit(struct sk_buff *skb, {struct dsa_port *dp =dsa_slave_to_port (dev);u8 *mtk_tag; +bool is_vlan_skb = true;..
Quoted 7 lines
net/dsa/tag_mtk.c +5
-1+/* Mark tag attribute on special tag insertion to notify hardware +* whether that's a combined special tag with 802.1Q header. +*/ + mtk_tag[0 ] = is_vlan_skb ?MTK_HDR_XMIT_TAGGED_TPID_8100 : +MTK_HDR_XMIT_UNTAGGED ; mtk_tag[1 ] = (1 << dp->index) &MTK_HDR_XMIT_DP_BIT_MASK ; - mtk_tag[2 ] =0 ;net/dsa/tag_mtk.c static struct sk_buff *mtk_tag_xmit(struct sk_buff *skb, · line 64
Quoted 10 lines
net/dsa/tag_mtk.c +6
-1- mtk_tag[3 ] =0 ; + +/* Tag control information is kept for 802.1Q */ +if (!is_vlan_skb) { + mtk_tag[2 ] =0 ; + mtk_tag[3 ] =0 ; + }return skb; }Hi Sean
So you can mark a packet for egress. What about ingress? How do you know the VLAN/PORT combination for packets the CPU receives? I would of expected a similar change to
mtk_tag_rcv().Quoted 7 lines
Quoted 1 line
Andrew
Hi, Andrew
It's unnecessary for extra handling in
mtk_tag_rcv()when VLAN tag is present since it is able to put the VLAN tag after the special tag and then follow the existing way to parse.
Quoted 7 lines
Hi Sean
O.K. Please mention this in the commit message. Since it was something i was expecting, it should be documented why it is not needed.
Thanks
Andrew
Sure. I will add this in the commit message.
Sean
Quoted 1 line
PATCH 3/3 net: dsa: mediatek: update MAINTAINERS entry with MediaTek switch driver
In reply to [email protected]From: Sean Wang <sean.wang-NuS5LvNUpcJWk0Htik3J/[email protected]>
I work for MediaTek and maintain SoC targeting to home gateway and also will keep extending and testing the function from MediaTek switch.
--- MAINTAINERS | 7 +++++++ 1 file changed, 7 insertions(+)
MAINTAINERS +7 -0
@@ -8723,6 +8723,13 @@ L: [email protected] S: Maintained F: drivers/net/ethernet/mediatek/ +MEDIATEK SWITCH DRIVER +M: Sean Wang <sean.wang-NuS5LvNUpcJWk0Htik3J/[email protected]> +L: [email protected] +S: Maintained +F: drivers/net/dsa/mt7530.* +F: net/dsa/tag_mtk.c + MEDIATEK JPEG DRIVER M: Rick Chang <rick.chang-NuS5LvNUpcJWk0Htik3J/[email protected]> M: Bin Liu <bin.liu-NuS5LvNUpcJWk0Htik3J/[email protected]>
Signature · 1 line
2.7.4
Re: [PATCH net-next 3/3] net: dsa: mediatek: update MAINTAINERS entry with MediaTek switch driver
Quoted 7 lines · On Thu, Dec 07, 2017 at 02:06:12PM +0800, [email protected] wrote:
From: Sean Wang <[email protected]>
I work for MediaTek and maintain SoC targeting to home gateway and also will keep extending and testing the function from MediaTek switch.
Signed-off-by Sean Wang <[email protected]>
Andrew