MIPS: ar9331: add watchdog support
Subsystems (2)
PATCH 1/4 MIPS: ar9331: add watchdog support
Signed-off-by Oleksij Rempel <[email protected]>
--- arch/mips/dts/ar9331.dtsi | 6 ++++++ drivers/watchdog/Kconfig | 2 +- 2 files changed, 7 insertions(+), 1 deletion(-)
arch/mips/dts/ar9331.dtsi +6 -0
@@ -1,5 +1,11 @@ / { ahb { + wdt0: wdt@18060008 { + compatible = "qca,ar9331-wdt", "qca,ar9344-wdt"; + reg = <0x18060008 0x8>; + clocks = <&pll ATH79_CLK_CPU>; + }; + mac0: mac@19000000 { compatible = "qca,ar9331-ge0"; reg = <0x18070000 0x00000100>,
drivers/watchdog/Kconfig +1 -1
@@ -12,7 +12,7 @@ if WATCHDOG config WATCHDOG_AR9344 bool "QCA AR9344" - depends on SOC_QCA_AR9344 + depends on SOC_QCA_AR9344 || SOC_QCA_AR9331 help Add support for watchdog on the QCA AR9344 SoC.
Signature · 7 lines
2.14.1 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 2/4 MIPS: ath79: ar9331: add generic RAM macro
with this macro, we should be able to cover most of existing ar9331 based boards.
Signed-off-by Oleksij Rempel <[email protected]>
--- arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 1 + arch/mips/mach-ath79/include/mach/pbl_macros.h | 37 +++++++++++++++++++++++-- 2 files changed, 35 insertions(+), 3 deletions(-)
arch/mips/mach-ath79/include/mach/ar71xx_regs.h +1 -0
@@ -139,6 +139,7 @@#define AR71XX_RESET_FULL_CHIP BIT(24) +#define AR933X_BOOTSTRAP_MEM_TYPE BIT(13)#define AR933X_BOOTSTRAP_REF_CLK_40 BIT(0)#endif /* __ASM_MACH_AR71XX_REGS_H */
arch/mips/mach-ath79/include/mach/pbl_macros.h +34 -3
@@ -172,6 +172,40 @@ .set pop .endm +#define RESET_REG_BOOTSTRAP ((KSEG1 | AR71XX_RESET_BASE) \ + | AR933X_RESET_REG_BOOTSTRAP) + +.macro pbl_ar9331_ram_generic_config + .set push + .set noreorder + + li t5, RESET_REG_BOOTSTRAP +/* Documentation and source code of existing boot loaders disagree at +* this place. Doc says: MEM_TYPE[13:12]: +* - 00 = SDRAM +* - 01 = DDR1 +* - 10 = DDR2 +* The source code of most loaders do not care about BIT(12). So we do +* the same. +*/ + li t6, AR933X_BOOTSTRAP_MEM_TYPE + lw t7, 0(t5); +and t6, t7, t6 + beq zero, t6, pbl_ar9331_ram_generic_ddr1 + nop + +pbl_ar9331_ram_generic_ddr2: + pbl_ar9331_ddr2_config + b pbl_ar9331_ram_generic_config + nop + +pbl_ar9331_ram_generic_ddr1: + pbl_ar9331_ddr1_config + +pbl_ar9331_ram_generic_config: + .set pop +.endm + #define GPIO_FUNC ((KSEG1 | AR71XX_GPIO_BASE) | AR71XX_GPIO_REG_FUNC) .macro pbl_ar9331_uart_enable
@@ -179,9 +213,6 @@ | AR933X_GPIO_FUNC_RSRV15, GPIO_FUNC .endm -#define RESET_REG_BOOTSTRAP ((KSEG1 | AR71XX_RESET_BASE) \ - | AR933X_RESET_REG_BOOTSTRAP) - .macro pbl_ar9331_mdio_gpio_enable/* Bit 18 enables MDC and MDIO function on GPIO26 and GPIO28 */ pbl_reg_set (1 << 18), RESET_REG_BOOTSTRAP
Signature · 7 lines
2.14.1 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 3/4 MIPS: ath79: ar9331: add ar9331_pbl_generic_start macro
In reply to Oleksij RempelMost of ar9331 boards have identical PBL. So we can sync the code to single macro.
Signed-off-by Oleksij Rempel <[email protected]>
--- arch/mips/mach-ath79/include/mach/pbl_macros.h | 35 ++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
arch/mips/mach-ath79/include/mach/pbl_macros.h +35 -0
@@ -368,4 +368,39 @@ normal_path: .set pop .endm + .macro ar9331_pbl_generic_start + .set push + .set noreorder + + mips_barebox_10h + + pbl_blt 0xbf000000 skip_pll_ram_config t8 + + hornet_mips24k_cp0_setup + +pbl_ar9331_wmac_enable + + hornet_1_1_war + +pbl_ar9331_pll + pbl_ar9331_ram_generic_config + +skip_pll_ram_config: +/* Initialize caches... */ +mips_cache_reset + +/* ... and enable them */ + dcache_enable + +pbl_ar9331_uart_enable + debug_ll_ar9331_init +mips_nmon + + pbl_ar9331_mdio_gpio_enable + + copy_to_link_location pbl_start + + .set pop + .endm +#endif /* __ASM_MACH_ATH79_PBL_MACROS_H */
Signature · 7 lines
2.14.1 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 4/4 MIPS: add support for DPTechnics DPT-Module v1
In reply to Oleksij RempelThis product can be found here:
https://dptechnics.com/en/products/dpt-module-v1.html
Signed-off-by Oleksij Rempel <[email protected]>
--- arch/mips/Makefile | 1 + arch/mips/boards/dptechnics-dpt-module/Makefile | 1 + arch/mips/boards/dptechnics-dpt-module/board.c | 8 ++ .../include/board/board_pbl_start.h | 20 +++++ arch/mips/configs/dptechnics-dpt-module_defconfig | 89 ++++++++++++++++++++++ arch/mips/dts/ar9331-dptechnics-dpt-module.dts | 31 ++++++++ arch/mips/mach-ath79/Kconfig | 7 ++ 7 files changed, 157 insertions(+) create mode 100644 arch/mips/boards/dptechnics-dpt-module/Makefile create mode 100644 arch/mips/boards/dptechnics-dpt-module/board.c create mode 100644 arch/mips/boards/dptechnics-dpt-module/include/board/board_pbl_start.h create mode 100644 arch/mips/configs/dptechnics-dpt-module_defconfig create mode 100644 arch/mips/dts/ar9331-dptechnics-dpt-module.dts
arch/mips/Makefile +1 -0
@@ -79,6 +79,7 @@ machine-$(CONFIG_MACH_MIPS_AR231X) := ar231x board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102 machine-$(CONFIG_MACH_MIPS_ATH79) := ath79 +board-$(CONFIG_BOARC_DPTECHNICS_DPT_MODULE) := dptechnics-dpt-module board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020 board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300 board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swift
arch/mips/boards/dptechnics-dpt-module/Makefile new file +1 -0
@@ -0,0 +1 @@ +obj-y += board.o
arch/mips/boards/dptechnics-dpt-module/board.c new file +8 -0
@@ -0,0 +1,8 @@ +#include <common.h> +#include <init.h> + +static int dummy_init (void ) +{ +return 0 ; +} +postcore_initcall (dummy_init);
arch/mips/boards/dptechnics-dpt-module/include/board/board_pbl_start.h new file +20 -0
@@ -0,0 +1,20 @@ +/* +* Copyright (C) 2017 Oleksij Rempel <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 +* as published by the Free Software Foundation. +*/ + +#include <asm/pbl_macros.h> +#include <mach/pbl_macros.h> +#include <asm/pbl_nmon.h> + + .macro board_pbl_start + .set push + .set noreorder + + ar9331_pbl_generic_start + + .set pop + .endm
arch/mips/configs/dptechnics-dpt-module_defconfig new file +89 -0
89 lines not on this page · raw message
arch/mips/dts/ar9331-dptechnics-dpt-module.dts new file +31 -0
@@ -0,0 +1,31 @@ +#include <mips/qca/ar9331_dpt_module.dts> +#include "ar9331.dtsi" + +/ { + aliases { + spiflash = &spiflash; + }; + + chosen { + environment@0 { + compatible = "barebox,environment"; + device-path = &spiflash, "partname:barebox-environment"; + }; + }; +}; + +&spiflash { + partition@0 { + label = "barebox"; + reg = <0 0x80000>; + }; + + partition@80000 { + label = "barebox-environment"; + reg = <0x80000 0x10000>; + }; +}; + +&mac0 { + status = "okay"; +};
arch/mips/mach-ath79/Kconfig +7 -0
@@ -13,6 +13,13 @@ config SOC_QCA_AR9344 choice prompt "Board type" +config BOARC_DPTECHNICS_DPT_MODULE + bool "DPTechnics DPT-Module" + select SOC_QCA_AR9331 + select HAVE_PBL_IMAGE + select HAVE_IMAGE_COMPRESSION + select HAS_NMON + config BOARD_TPLINK_MR3020 bool "TP-LINK MR3020" select SOC_QCA_AR9331
Signature · 7 lines
2.14.1 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH v1 4/4] MIPS: add support for DPTechnics DPT-Module v1
Quoted 44 lines · On Sat, 9 Dec 2017 10:59:38 +0100 Oleksij Rempel <[email protected]>…
This product can be found here:
https://dptechnics.com/en/products/dpt-module-v1.htmlSigned-off-by Oleksij Rempel <[email protected]>--- arch/mips/Makefile | 1 + arch/mips/boards/dptechnics-dpt-module/Makefile | 1 + arch/mips/boards/dptechnics-dpt-module/board.c | 8 ++ .../include/board/board_pbl_start.h | 20 +++++ arch/mips/configs/dptechnics-dpt-module_defconfig | 89 ++++++++++++++++++++++ arch/mips/dts/ar9331-dptechnics-dpt-module.dts | 31 ++++++++ arch/mips/mach-ath79/Kconfig | 7 ++ 7 files changed, 157 insertions(+) create mode 100644 arch/mips/boards/dptechnics-dpt-module/Makefile create mode 100644 arch/mips/boards/dptechnics-dpt-module/board.c create mode 100644 arch/mips/boards/dptechnics-dpt-module/include/board/board_pbl_start.h create mode 100644 arch/mips/configs/dptechnics-dpt-module_defconfig create mode 100644 arch/mips/dts/ar9331-dptechnics-dpt-module.dtsarch/mips/Makefile +1
-0@@ -79,6 +79,7 @@ machine-$(CONFIG_MACH_MIPS_AR231X) := ar231x board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102 machine-$(CONFIG_MACH_MIPS_ATH79) := ath79 +board-$(CONFIG_BOARC_DPTECHNICS_DPT_MODULE) := dptechnics-dpt-module board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020 board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300 board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swiftarch/mips/boards/dptechnics-dpt-module/Makefile new file +1
-0@@ -0,0 +1 @@ +obj-y += board.oarch/mips/boards/dptechnics-dpt-module/board.c new file +0
-0
arch/mips/boards/dptechnics-dpt-module/board.c line 8
Quoted 8 lines
arch/mips/boards/dptechnics-dpt-module/board.c new file +8
-0@@ -0,0 +1,8 @@ +#include <common.h> +#include <init.h> + +static int dummy_init (void ) +{ +return 0 ; +} +postcore_initcall (dummy_init);
Do we really need this dummy_init()?
Quoted 184 lines
arch/mips/boards/dptechnics-dpt-module/include/board/board_pbl_start.h new file +20
-0@@ -0,0 +1,20 @@ +/* +* Copyright (C) 2017 Oleksij Rempel <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 +* as published by the Free Software Foundation. +*/ + +#include <asm/pbl_macros.h> +#include <mach/pbl_macros.h> +#include <asm/pbl_nmon.h> + + .macro board_pbl_start + .set push + .set noreorder + + ar9331_pbl_generic_start + + .set pop + .endmarch/mips/configs/dptechnics-dpt-module_defconfig new file +89
-0@@ -0,0 +1,89 @@ +CONFIG_BUILTIN_DTB=y +CONFIG_BUILTIN_DTB_NAME="ar9331-dptechnics-dpt-module" +CONFIG_MACH_MIPS_ATH79=y +CONFIG_BOARC_QCA_AR9331_GENERIC=y +CONFIG_PBL_IMAGE=y +CONFIG_IMAGE_COMPRESSION_XZKERN=y +CONFIG_MMU=y +CONFIG_TEXT_BASE=0x82000000 +CONFIG_MALLOC_TLSF=y +CONFIG_HUSH_FANCY_PROMPT=y +CONFIG_CMDLINE_EDITING=y +CONFIG_AUTO_COMPLETE=y +CONFIG_CONSOLE_RATP=y +CONFIG_DEFAULT_ENVIRONMENT_GENERIC_NEW=y +CONFIG_RESET_SOURCE=y +CONFIG_CMD_DMESG=y +CONFIG_LONGHELP=y +CONFIG_CMD_IOMEM=y +CONFIG_CMD_IMD=y +CONFIG_CMD_MEMINFO=y +CONFIG_CMD_GO=y +CONFIG_CMD_LOADB=y +CONFIG_CMD_LOADY=y +CONFIG_CMD_RESET=y +CONFIG_CMD_EXPORT=y +CONFIG_CMD_DEFAULTENV=y +CONFIG_CMD_LOADENV=y +CONFIG_CMD_MAGICVAR=y +CONFIG_CMD_MAGICVAR_HELP=y +CONFIG_CMD_SAVEENV=y +CONFIG_CMD_SHA1SUM=y +CONFIG_CMD_UNCOMPRESS=y +CONFIG_CMD_LET=y +CONFIG_CMD_MSLEEP=y +CONFIG_CMD_READF=y +CONFIG_CMD_SLEEP=y +CONFIG_CMD_DHCP=y +CONFIG_CMD_HOST=y +CONFIG_CMD_MIITOOL=y +CONFIG_CMD_PING=y +CONFIG_CMD_ECHO_E=y +CONFIG_CMD_EDIT=y +CONFIG_CMD_READLINE=y +CONFIG_CMD_TIMEOUT=y +CONFIG_CMD_CRC=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_MM=y +CONFIG_CMD_CLK=y +CONFIG_CMD_DETECT=y +CONFIG_CMD_FLASH=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_LED=y +CONFIG_CMD_POWEROFF=y +CONFIG_CMD_SPI=y +CONFIG_CMD_LED_TRIGGER=y +CONFIG_CMD_WD=y +CONFIG_CMD_BAREBOX_UPDATE=y +CONFIG_CMD_OF_NODE=y +CONFIG_CMD_OF_PROPERTY=y +CONFIG_CMD_OFTREE=y +CONFIG_CMD_TIME=y +CONFIG_NET=y +CONFIG_NET_NFS=y +CONFIG_NET_NETCONSOLE=y +CONFIG_NET_SNTP=y +CONFIG_OFDEVICE=y +CONFIG_OF_BAREBOX_DRIVERS=y +CONFIG_OF_BAREBOX_ENV_IN_FS=y +CONFIG_DRIVER_SERIAL_AR933X=y +CONFIG_DRIVER_NET_AG71XX=y +CONFIG_AR8327N_PHY=y +CONFIG_AT803X_PHY=y +CONFIG_MDIO_BITBANG=y +CONFIG_MDIO_GPIO=y +CONFIG_DRIVER_SPI_ATH79=y +CONFIG_MTD=y +# CONFIG_MTD_OOB_DEVICE is not set +CONFIG_MTD_M25P80=y +CONFIG_LED=y +CONFIG_LED_GPIO=y +CONFIG_LED_GPIO_OF=y +CONFIG_LED_TRIGGERS=y +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_AR9344=y +CONFIG_FS_TFTP=y +CONFIG_FS_NFS=y +CONFIG_FS_RATP=y +CONFIG_DIGEST_SHA224_GENERIC=y +CONFIG_DIGEST_SHA256_GENERIC=yarch/mips/dts/ar9331-dptechnics-dpt-module.dts new file +31
-0@@ -0,0 +1,31 @@ +#include <mips/qca/ar9331_dpt_module.dts> +#include "ar9331.dtsi" + +/ { + aliases { + spiflash = &spiflash; + }; + + chosen { + environment@0 { + compatible = "barebox,environment"; + device-path = &spiflash, "partname:barebox-environment"; + }; + }; +}; + +&spiflash { + partition@0 { + label = "barebox"; + reg = <0 0x80000>; + }; + + partition@80000 { + label = "barebox-environment"; + reg = <0x80000 0x10000>; + }; +}; + +&mac0 { + status = "okay"; +};arch/mips/mach-ath79/Kconfig +7
-0@@ -13,6 +13,13 @@ config SOC_QCA_AR9344 choice prompt "Board type" +config BOARC_DPTECHNICS_DPT_MODULE + bool "DPTechnics DPT-Module" + select SOC_QCA_AR9331 + select HAVE_PBL_IMAGE + select HAVE_IMAGE_COMPRESSION + select HAS_NMON + config BOARD_TPLINK_MR3020 bool "TP-LINK MR3020" select SOC_QCA_AR9331Signature · 7 lines
2.14.1 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Signature · 7 lines
Best regards, Antony Pavlov _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH v1 4/4] MIPS: add support for DPTechnics DPT-Module v1
Am 09.12.2017 um 17:54 schrieb Antony Pavlov:
Quoted 50 lines
Quoted 47 lines · On Sat, 9 Dec 2017 10:59:38 +0100 Oleksij Rempel <[email protected]>…
This product can be found here:
https://dptechnics.com/en/products/dpt-module-v1.htmlSigned-off-by Oleksij Rempel <[email protected]>--- arch/mips/Makefile | 1 + arch/mips/boards/dptechnics-dpt-module/Makefile | 1 + arch/mips/boards/dptechnics-dpt-module/board.c | 8 ++ .../include/board/board_pbl_start.h | 20 +++++ arch/mips/configs/dptechnics-dpt-module_defconfig | 89 ++++++++++++++++++++++ arch/mips/dts/ar9331-dptechnics-dpt-module.dts | 31 ++++++++ arch/mips/mach-ath79/Kconfig | 7 ++ 7 files changed, 157 insertions(+) create mode 100644 arch/mips/boards/dptechnics-dpt-module/Makefile create mode 100644 arch/mips/boards/dptechnics-dpt-module/board.c create mode 100644 arch/mips/boards/dptechnics-dpt-module/include/board/board_pbl_start.h create mode 100644 arch/mips/configs/dptechnics-dpt-module_defconfig create mode 100644 arch/mips/dts/ar9331-dptechnics-dpt-module.dtsarch/mips/Makefile +1
-0@@ -79,6 +79,7 @@ machine-$(CONFIG_MACH_MIPS_AR231X) := ar231x board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102 machine-$(CONFIG_MACH_MIPS_ATH79) := ath79 +board-$(CONFIG_BOARC_DPTECHNICS_DPT_MODULE) := dptechnics-dpt-module board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020 board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300 board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swiftarch/mips/boards/dptechnics-dpt-module/Makefile new file +1
-0@@ -0,0 +1 @@ +obj-y += board.oarch/mips/boards/dptechnics-dpt-module/board.c new file +3
-0@@ -0,0 +1,8 @@ +#include <common.h> +#include <init.h> +
Quoted 8 lines
arch/mips/boards/dptechnics-dpt-module/board.c line 8
Quoted 5 lines
arch/mips/boards/dptechnics-dpt-module/board.c new file +5
-0+static int dummy_init (void ) +{ +return 0 ; +} +postcore_initcall (dummy_init);Do we really need this
dummy_init()?
No, but other ways we need to fix the build system. And right now i have no time for that :(
Signature · 2 lines
Regards, Oleksij
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH v1 4/4] MIPS: add support for DPTechnics DPT-Module v1
Quoted 60 lines · Oleksij Rempel
Am 09.12.2017 um 17:54 schrieb Antony Pavlov:
Quoted 50 lines
Quoted 47 lines · On Sat, 9 Dec 2017 10:59:38 +0100 Oleksij Rempel <[email protected]>…
This product can be found here:
https://dptechnics.com/en/products/dpt-module-v1.htmlSigned-off-by Oleksij Rempel <[email protected]>--- arch/mips/Makefile | 1 + arch/mips/boards/dptechnics-dpt-module/Makefile | 1 + arch/mips/boards/dptechnics-dpt-module/board.c | 8 ++ .../include/board/board_pbl_start.h | 20 +++++ arch/mips/configs/dptechnics-dpt-module_defconfig | 89 ++++++++++++++++++++++ arch/mips/dts/ar9331-dptechnics-dpt-module.dts | 31 ++++++++ arch/mips/mach-ath79/Kconfig | 7 ++ 7 files changed, 157 insertions(+) create mode 100644 arch/mips/boards/dptechnics-dpt-module/Makefile create mode 100644 arch/mips/boards/dptechnics-dpt-module/board.c create mode 100644 arch/mips/boards/dptechnics-dpt-module/include/board/board_pbl_start.h create mode 100644 arch/mips/configs/dptechnics-dpt-module_defconfig create mode 100644 arch/mips/dts/ar9331-dptechnics-dpt-module.dtsarch/mips/Makefile +1
-0@@ -79,6 +79,7 @@ machine-$(CONFIG_MACH_MIPS_AR231X) := ar231x board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102 machine-$(CONFIG_MACH_MIPS_ATH79) := ath79 +board-$(CONFIG_BOARC_DPTECHNICS_DPT_MODULE) := dptechnics-dpt-module board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020 board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300 board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swiftarch/mips/boards/dptechnics-dpt-module/Makefile new file +1
-0@@ -0,0 +1 @@ +obj-y += board.oarch/mips/boards/dptechnics-dpt-module/board.c new file +3
-0@@ -0,0 +1,8 @@ +#include <common.h> +#include <init.h> +Quoted 8 lines
arch/mips/boards/dptechnics-dpt-module/board.c line 8
Quoted 5 lines
arch/mips/boards/dptechnics-dpt-module/board.c new file +5
-0+static int dummy_init (void ) +{ +return 0 ; +} +postcore_initcall (dummy_init);Do we really need this
dummy_init()?
Quoted 2 lines
No, but other ways we need to fix the build system. And right now i have no time for that :(
Are you sure you need the dummy_init()? I just gave it a test and I indeed needed a C file to get it through the linker, but that C file can equally well be empty.
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH v1 4/4] MIPS: add support for DPTechnics DPT-Module v1
Am 12.12.2017 um 07:50 schrieb Sascha Hauer:
Quoted 61 lines · Oleksij Rempel
Quoted 60 lines
Am 09.12.2017 um 17:54 schrieb Antony Pavlov:
Quoted 58 lines
Quoted 44 lines · On Sat, 9 Dec 2017 10:59:38 +0100 Oleksij Rempel <[email protected]>…
This product can be found here:
https://dptechnics.com/en/products/dpt-module-v1.htmlSigned-off-by Oleksij Rempel <[email protected]>--- arch/mips/Makefile | 1 + arch/mips/boards/dptechnics-dpt-module/Makefile | 1 + arch/mips/boards/dptechnics-dpt-module/board.c | 8 ++ .../include/board/board_pbl_start.h | 20 +++++ arch/mips/configs/dptechnics-dpt-module_defconfig | 89 ++++++++++++++++++++++ arch/mips/dts/ar9331-dptechnics-dpt-module.dts | 31 ++++++++ arch/mips/mach-ath79/Kconfig | 7 ++ 7 files changed, 157 insertions(+) create mode 100644 arch/mips/boards/dptechnics-dpt-module/Makefile create mode 100644 arch/mips/boards/dptechnics-dpt-module/board.c create mode 100644 arch/mips/boards/dptechnics-dpt-module/include/board/board_pbl_start.h create mode 100644 arch/mips/configs/dptechnics-dpt-module_defconfig create mode 100644 arch/mips/dts/ar9331-dptechnics-dpt-module.dtsarch/mips/Makefile +1
-0@@ -79,6 +79,7 @@ machine-$(CONFIG_MACH_MIPS_AR231X) := ar231x board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102 machine-$(CONFIG_MACH_MIPS_ATH79) := ath79 +board-$(CONFIG_BOARC_DPTECHNICS_DPT_MODULE) := dptechnics-dpt-module board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020 board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300 board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swiftarch/mips/boards/dptechnics-dpt-module/Makefile new file +1
-0@@ -0,0 +1 @@ +obj-y += board.oarch/mips/boards/dptechnics-dpt-module/board.c new file +0
-0arch/mips/boards/dptechnics-dpt-module/board.c line 8
Quoted 8 lines
arch/mips/boards/dptechnics-dpt-module/board.c new file +8
-0@@ -0,0 +1,8 @@ +#include <common.h> +#include <init.h> + +static int dummy_init (void ) +{ +return 0 ; +} +postcore_initcall (dummy_init);Do we really need this
dummy_init()?
Quoted 6 lines
Quoted 2 lines
No, but other ways we need to fix the build system. And right now i have no time for that :(
Are you sure you need the
dummy_init()? I just gave it a test and I indeed needed a C file to get it through the linker, but that C file can equally well be empty.
Ok, i'll try it.
Signature · 2 lines
Regards, Oleksij
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox