Skip to contentSkip to conversation

sh_eth: get Ether port # only when needed

PATCH In review Sergei Shtylyov 2 participants 2 messages Jan 14, 2018 – Jan 15, 2018

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 2/2 sh_eth: get Ether port # only when needed

The dual-port Ether configurations always have a shared TSU to e.g. pass the packets between those ports. With the TSU init. code gathered under the single *if*, we now can only get the port # from 'platform_device::id' only when we actually need it (and not recalculate it each time)...

---
 drivers/net/ethernet/renesas/sh_eth.c |   13 +++++--------
 1 file changed, 5 insertions(+), 8 deletions(-)

Index: net-next/drivers/net/ethernet/renesas/sh_eth.c =================================--- net-next.orig/drivers/net/ethernet/renesas/sh_eth.c +++ net-next/drivers/net/ethernet/renesas/sh_eth.c
@@ -3125,7 +3125,7 @@ static int sh_eth_drv_probe(struct platf
const struct platform_device_id *id = platform_get_device_id(pdev); struct sh_eth_private *mdp;
struct net_device *ndev;
- int ret, devno;
+ int ret;

/* get base addr */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
@@ -3137,10 +3137,6 @@ static int sh_eth_drv_probe(struct platf
pm_runtime_enable(&pdev->dev); pm_runtime_get_sync(&pdev->dev);

- devno = pdev->id;
- if (devno < 0)
- devno = 0;
-
ret = platform_get_irq(pdev, 0);
if (ret < 0)
goto out_release;
@@ -3223,6 +3219,7 @@ static int sh_eth_drv_probe(struct platf
}

if (mdp->cd->tsu) {
+ int port = pdev->id < 0 ? 0 : pdev->id % 2;
struct resource *rtsu;

rtsu = platform_get_resource(pdev, IORESOURCE_MEM, 1);
@@ -3234,7 +3231,7 @@ static int sh_eth_drv_probe(struct platf
/* We can only request the TSU region for the first port
* of the two sharing this TSU for the probe to succeed... */
- if (devno % 2 = 0 &&
+ if (port = 0 &&
!devm_request_mem_region(&pdev->dev, rtsu->start,
resource_size(rtsu), dev_name(&pdev->dev))) {
@@ -3250,11 +3247,11 @@ static int sh_eth_drv_probe(struct platf
ret = -ENOMEM;
goto out_release;
}
- mdp->port = devno % 2;
+ mdp->port = port;
ndev->features = NETIF_F_HW_VLAN_CTAG_FILTER;

/* Need to init only the first port of the two sharing a TSU */
- if (devno % 2 = 0) {
+ if (port = 0) {
if (mdp->cd->chip_reset)
mdp->cd->chip_reset(ndev);

Reviewed-by on v1 2/2
#1 lore raw
Quoted 6 lines · Sergei Shtylyov

The dual-port Ether configurations always have a shared TSU to e.g. pass the packets between those ports. With the TSU init. code gathered under the single *if*, we now can only get the port # from 'platform_device::id' only when we actually need it (and not recalculate it each time)...

Gr{oetje,eeting}s,

Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds