Skip to contentSkip to conversation

cadence-quadspi: Fix issues with non 32bit aligned accesses

PATCH New Vignesh R 2 participants 5 messages Jan 24, 2018 – Jan 26, 2018 SPI

lore
Share & tools
lore

Vignesh R

author
#0 lore raw

v3 cover cadence-quadspi: Fix issues with non 32bit aligned accesses

This series reverts use of bounce_buf.c for non-DMA related alignment restriction and replaces it with local bounce buffer to handle problems with non 32 bit aligned writes on TI platforms.
Based on top of Jason's series:
[PATCH v6 0/4] spi: cadence_spi: Adopt Linux DT bindings

Tested on K2G EVM.

v3:
Rebased on top of latest u-boot-spi/master changes.

Goldschmidt Simon (1):
Revert "spi: cadence_qspi_apb: Use 32 bit indirect read transaction
when possible"

Vignesh R (2):
Revert "spi: cadence_qspi_apb: Use 32 bit indirect write transaction
when possible"
spi: cadence_qspi_apb: Make flash writes 32 bit aligned

 drivers/spi/cadence_qspi_apb.c   | 53 ++++++++++++++++++++--------------------
 include/configs/k2g_evm.h        |  1 -
 include/configs/socfpga_common.h |  1 -
 include/configs/stv0991.h        |  1 -
 4 files changed, 26 insertions(+), 30 deletions(-)
Signature · 1 line
2.16.0
author
#1 lore raw

PATCH v3 1/3 Revert "spi: cadence_qspi_apb: Use 32 bit indirect read transaction when possible"

From: Goldschmidt Simon <[email protected]>

This reverts commit b63b46313ed29e9b0c36b3d6b9407f6eade40c8f.

This commit changed cadence_qspi_apb to use bouncebuf.c, which invalidates the data cache after reading. This is meant for dma transfers only and breaks the cadence_qspi driver which copies via cpu only: data that is copied by the cpu is in cache only and the cache invalidation at the end throws away this data.

---
 drivers/spi/cadence_qspi_apb.c | 26 ++++++++++----------------
 1 file changed, 10 insertions(+), 16 deletions(-)
drivers/spi/cadence_qspi_apb.c +10 -16
index 4b1ddd79b30b..82e8a9ec4d1c 100644
@@ -627,8 +627,6 @@ int cadence_qspi_apb_indirect_read_execute(struct cadence_spi_platdata *plat,
 {
 	unsigned int remaining = n_rx;
 	unsigned int bytes_to_read = 0;
-	struct bounce_buffer bb;
-	u8 *bb_rxbuf;
 	int ret;
 
 	writel(n_rx, plat->regbase + CQSPI_REG_INDIRECTRDBYTES);
@@ -637,11 +635,6 @@ int cadence_qspi_apb_indirect_read_execute(struct cadence_spi_platdata *plat,
 	writel(CQSPI_REG_INDIRECTRD_START,
 	       plat->regbase + CQSPI_REG_INDIRECTRD);
 
-	ret = bounce_buffer_start(&bb, (void *)rxbuf, n_rx, GEN_BB_WRITE);
-	if (ret)
-		return ret;
-	bb_rxbuf = bb.bounce_buffer;
-
 	while (remaining > 0) {
 		ret = cadence_qspi_wait_for_data(plat);
 		if (ret < 0) {
@@ -655,13 +648,16 @@ int cadence_qspi_apb_indirect_read_execute(struct cadence_spi_platdata *plat,
 			bytes_to_read *= plat->fifo_width;
 			bytes_to_read = bytes_to_read > remaining ?
 					remaining : bytes_to_read;
-			readsl(plat->ahbbase, bb_rxbuf, bytes_to_read >> 2);
-			if (bytes_to_read % 4)
-				readsb(plat->ahbbase,
-				       bb_rxbuf + rounddown(bytes_to_read, 4),
-				       bytes_to_read % 4);
-
-			bb_rxbuf += bytes_to_read;
+			/*
+			 * Handle non-4-byte aligned access to avoid
+			 * data abort.
+			 */
+			if (((uintptr_t)rxbuf % 4) || (bytes_to_read % 4))
+				readsb(plat->ahbbase, rxbuf, bytes_to_read);
+			else
+				readsl(plat->ahbbase, rxbuf,
+				       bytes_to_read >> 2);
+			rxbuf += bytes_to_read;
 			remaining -= bytes_to_read;
 			bytes_to_read = cadence_qspi_get_rd_sram_level(plat);
 		}
@@ -678,7 +674,6 @@ int cadence_qspi_apb_indirect_read_execute(struct cadence_spi_platdata *plat,
 	/* Clear indirect completion status */
 	writel(CQSPI_REG_INDIRECTRD_DONE,
 	       plat->regbase + CQSPI_REG_INDIRECTRD);
-	bounce_buffer_stop(&bb);
 
 	return 0;
 
@@ -686,7 +681,6 @@ failrd:
 	/* Cancel the indirect read */
 	writel(CQSPI_REG_INDIRECTRD_CANCEL,
 	       plat->regbase + CQSPI_REG_INDIRECTRD);
-	bounce_buffer_stop(&bb);
 	return ret;
 }
 
Signature · 1 line
2.16.0
author
#2 lore raw

PATCH v3 2/3 Revert "spi: cadence_qspi_apb: Use 32 bit indirect write transaction when possible"

In reply to Vignesh R

This reverts commit 57897c13de03ac0136d64641a3eab526c6810387.

Using bounce_buf.c to handle non-DMA alignment problems is bad as bounce_buf.c does cache manipulations which is not required. Therefore revert this patch in favour of local bounce buffer solution in the next patch.

---
 drivers/spi/cadence_qspi_apb.c   | 26 ++++++--------------------
 include/configs/k2g_evm.h        |  1 -
 include/configs/socfpga_common.h |  1 -
 include/configs/stv0991.h        |  1 -
 4 files changed, 6 insertions(+), 23 deletions(-)
drivers/spi/cadence_qspi_apb.c +6 -20
index 82e8a9ec4d1c..a57109865d29 100644
@@ -30,7 +30,6 @@
 #include <linux/errno.h>
 #include <wait_bit.h>
 #include <spi.h>
-#include <bouncebuf.h>
 #include "cadence_qspi.h"
 
 #define CQSPI_REG_POLL_US			1 /* 1us */
@@ -722,17 +721,6 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
 	unsigned int remaining = n_tx;
 	unsigned int write_bytes;
 	int ret;
-	struct bounce_buffer bb;
-	u8 *bb_txbuf;
-
-	/*
-	 * Handle non-4-byte aligned accesses via bounce buffer to
-	 * avoid data abort.
-	 */
-	ret = bounce_buffer_start(&bb, (void *)txbuf, n_tx, GEN_BB_READ);
-	if (ret)
-		return ret;
-	bb_txbuf = bb.bounce_buffer;
 
 	/* Configure the indirect read transfer bytes */
 	writel(n_tx, plat->regbase + CQSPI_REG_INDIRECTWRBYTES);
@@ -743,11 +731,11 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
 
 	while (remaining > 0) {
 		write_bytes = remaining > page_size ? page_size : remaining;
-		writesl(plat->ahbbase, bb_txbuf, write_bytes >> 2);
-		if (write_bytes % 4)
-			writesb(plat->ahbbase,
-				bb_txbuf + rounddown(write_bytes, 4),
-				write_bytes % 4);
+		/* Handle non-4-byte aligned access to avoid data abort. */
+		if (((uintptr_t)txbuf % 4) || (write_bytes % 4))
+			writesb(plat->ahbbase, txbuf, write_bytes);
+		else
+			writesl(plat->ahbbase, txbuf, write_bytes >> 2);
 
 		ret = wait_for_bit_le32(plat->regbase + CQSPI_REG_SDRAMLEVEL,
 					CQSPI_REG_SDRAMLEVEL_WR_MASK <<
@@ -757,7 +745,7 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
 			goto failwr;
 		}
 
-		bb_txbuf += write_bytes;
+		txbuf += write_bytes;
 		remaining -= write_bytes;
 	}
 
@@ -768,7 +756,6 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
 		printf("Indirect write completion error (%i)\n", ret);
 		goto failwr;
 	}
-	bounce_buffer_stop(&bb);
 
 	/* Clear indirect completion status */
 	writel(CQSPI_REG_INDIRECTWR_DONE,
@@ -779,7 +766,6 @@ failwr:
 	/* Cancel the indirect write */
 	writel(CQSPI_REG_INDIRECTWR_CANCEL,
 	       plat->regbase + CQSPI_REG_INDIRECTWR);
-	bounce_buffer_stop(&bb);
 	return ret;
 }
 
include/configs/k2g_evm.h +0 -1
index 535e7124fc80..0a38922a519e 100644
@@ -93,7 +93,6 @@
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_CADENCE_QSPI
 #define CONFIG_CQSPI_REF_CLK 384000000
-#define CONFIG_BOUNCE_BUFFER
 #endif
 
 #define SPI_MTD_PARTS	KEYSTONE_SPI1_MTD_PARTS
include/configs/socfpga_common.h +0 -1
index ec8bb500504a..f6607b101ec5 100644
@@ -184,7 +184,6 @@ unsigned int cm_get_l4_sp_clk_hz(void);
 unsigned int cm_get_qspi_controller_clk_hz(void);
 #define CONFIG_CQSPI_REF_CLK		cm_get_qspi_controller_clk_hz()
 #endif
-#define CONFIG_BOUNCE_BUFFER
 
 /*
  * Designware SPI support
include/configs/stv0991.h +0 -1
index fd96979bf897..beb8f1ae9a92 100644
@@ -64,7 +64,6 @@
 + */
 #ifdef CONFIG_OF_CONTROL		/* QSPI is controlled via DT */
 #define CONFIG_CQSPI_REF_CLK		((30/4)/2)*1000*1000
-#define CONFIG_BOUNCE_BUFFER
 
 #endif
 
Signature · 1 line
2.16.0
author
#3 lore raw

PATCH v3 3/3 spi: cadence_qspi_apb: Make flash writes 32 bit aligned

In reply to Vignesh R

Make flash writes 32 bit aligned by using bounce buffers to deal with non 32 bit aligned buffers.
This is required because as per TI K2G TRM[1], the external master is only permitted to issue 32-bit data interface writes until the last word of an indirect transfer. Otherwise indirect writes is known to fail sometimes.

[1] http://www.ti.com/lit/ug/spruhy8g/spruhy8g.pdf

---
 drivers/spi/cadence_qspi_apb.c | 31 +++++++++++++++++++++++++------
 1 file changed, 25 insertions(+), 6 deletions(-)
drivers/spi/cadence_qspi_apb.c +25 -6
index a57109865d29..6d9a7941b470 100644
@@ -30,6 +30,7 @@
 #include <linux/errno.h>
 #include <wait_bit.h>
 #include <spi.h>
+#include <malloc.h>
 #include "cadence_qspi.h"
 
 #define CQSPI_REG_POLL_US			1 /* 1us */
@@ -719,9 +720,23 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
 {
 	unsigned int page_size = plat->page_size;
 	unsigned int remaining = n_tx;
+	const u8 *bb_txbuf = txbuf;
+	void *bounce_buf = NULL;
 	unsigned int write_bytes;
 	int ret;
 
+	/*
+	 * Use bounce buffer for non 32 bit aligned txbuf to avoid data
+	 * aborts
+	 */
+	if ((uintptr_t)txbuf % 4) {
+		bounce_buf = malloc(n_tx);
+		if (!bounce_buf)
+			return -ENOMEM;
+		memcpy(bounce_buf, txbuf, n_tx);
+		bb_txbuf = bounce_buf;
+	}
+
 	/* Configure the indirect read transfer bytes */
 	writel(n_tx, plat->regbase + CQSPI_REG_INDIRECTWRBYTES);
 
@@ -731,11 +746,11 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
 
 	while (remaining > 0) {
 		write_bytes = remaining > page_size ? page_size : remaining;
-		/* Handle non-4-byte aligned access to avoid data abort. */
-		if (((uintptr_t)txbuf % 4) || (write_bytes % 4))
-			writesb(plat->ahbbase, txbuf, write_bytes);
-		else
-			writesl(plat->ahbbase, txbuf, write_bytes >> 2);
+		writesl(plat->ahbbase, bb_txbuf, write_bytes >> 2);
+		if (write_bytes % 4)
+			writesb(plat->ahbbase,
+				bb_txbuf + rounddown(write_bytes, 4),
+				write_bytes % 4);
 
 		ret = wait_for_bit_le32(plat->regbase + CQSPI_REG_SDRAMLEVEL,
 					CQSPI_REG_SDRAMLEVEL_WR_MASK <<
@@ -745,7 +760,7 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
 			goto failwr;
 		}
 
-		txbuf += write_bytes;
+		bb_txbuf += write_bytes;
 		remaining -= write_bytes;
 	}
 
@@ -760,12 +775,16 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat,
 	/* Clear indirect completion status */
 	writel(CQSPI_REG_INDIRECTWR_DONE,
 	       plat->regbase + CQSPI_REG_INDIRECTWR);
+	if (bounce_buf)
+		free(bounce_buf);
 	return 0;
 
 failwr:
 	/* Cancel the indirect write */
 	writel(CQSPI_REG_INDIRECTWR_CANCEL,
 	       plat->regbase + CQSPI_REG_INDIRECTWR);
+	if (bounce_buf)
+		free(bounce_buf);
 	return ret;
 }
 
Signature · 1 line
2.16.0
#4 lore raw

v3 cover cadence-quadspi: Fix issues with non 32bit aligned accesses

In reply to Vignesh R
Quoted 11 lines · Vignesh R

This series reverts use of bounce_buf.c for non-DMA related alignment restriction and replaces it with local bounce buffer to handle problems with non 32 bit aligned writes on TI platforms.
Based on top of Jason's series:
[PATCH v6 0/4] spi: cadence_spi: Adopt Linux DT bindings

Tested on K2G EVM.

v3:
Rebased on top of latest u-boot-spi/master changes.

Quoted 8 lines

Goldschmidt Simon (1):
Revert "spi: cadence_qspi_apb: Use 32 bit indirect read transaction
when possible"

Vignesh R (2):
Revert "spi: cadence_qspi_apb: Use 32 bit indirect write transaction
when possible"
spi: cadence_qspi_apb: Make flash writes 32 bit aligned

Applied to u-boot-spi/master, thanks!