Skip to contentSkip to conversation

macchiatobin: bump kernel and u-boot versions

PATCH New Sergey Matyukevich 2 participants 2 messages Jan 30, 2018

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 macchiatobin: bump kernel and u-boot versions

Bump Linux to 4.15 and U-Boot to 2018.01. Remove networking dts patches since they has landed in Linux 4.15. Update readme.txt: fix mainline BSP versions and update boot selection for board rev 1.3.

---
 ...arvell-extend-the-cp110-syscon-register-a.patch |  45 --------
 ...arvell-add-comphy-nodes-on-cp110-master-a.patch | 118 ---------------------
 ...arvell-mcbin-add-comphy-references-to-Eth.patch |  58 ----------
 board/solidrun/macchiatobin/readme.txt             |  26 +++--
 configs/solidrun_macchiatobin_mainline_defconfig   |   7 +-
 5 files changed, 20 insertions(+), 234 deletions(-)
 delete mode 100644 board/solidrun/macchiatobin/patches/linux/0001-arm64-dts-marvell-extend-the-cp110-syscon-register-a.patch
 delete mode 100644 board/solidrun/macchiatobin/patches/linux/0002-arm64-dts-marvell-add-comphy-nodes-on-cp110-master-a.patch
 delete mode 100644 board/solidrun/macchiatobin/patches/linux/0003-arm64-dts-marvell-mcbin-add-comphy-references-to-Eth.patch
board/solidrun/macchiatobin/patches/linux/0001-arm64-dts-marvell-extend-the-cp110-syscon-register-a.patch deleted +0 -45
deleted file mode 100644
index bcfeb1ecf9..0000000000
@@ -1,45 +0,0 @@
-From c25a2b8559989011d43fb901824dd8b981fc6b7b Mon Sep 17 00:00:00 2001
-From: Sergey Matyukevich <[email protected]>
-Date: Fri, 8 Dec 2017 23:08:34 +0300
-Subject: [PATCH] arm64: dts: marvell: extend the cp110 syscon register area length
-
-This patch extends on both cp110 the system register area length to
-include some of the comphy registers as well.
-
-Signed-off-by: Antoine Tenart <[email protected]>
-Signed-off-by: Gregory CLEMENT <[email protected]>
-Signed-off-by: Sergey Matyukevich <[email protected]>
----
- arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi | 2 +-
- arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi  | 2 +-
- 2 files changed, 2 insertions(+), 2 deletions(-)
-
-diff --git a/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi
-index f2aa2a81de4d..4dd8c7d53764 100644
---- a/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi
-+++ b/arch/arm64/boot/dts/marvell/armada-cp110-master.dtsi
-@@ -143,7 +143,7 @@
- 
- 			cpm_syscon0: system-controller at 440000 {
- 				compatible = "syscon", "simple-mfd";
--				reg = <0x440000 0x1000>;
-+				reg = <0x440000 0x2000>;
- 
- 				cpm_clk: clock {
- 					compatible = "marvell,cp110-clock";
-diff --git a/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi
-index 4fe70323abb3..43fa491da6ce 100644
---- a/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi
-+++ b/arch/arm64/boot/dts/marvell/armada-cp110-slave.dtsi
-@@ -143,7 +143,7 @@
- 
- 			cps_syscon0: system-controller at 440000 {
- 				compatible = "syscon", "simple-mfd";
--				reg = <0x440000 0x1000>;
-+				reg = <0x440000 0x2000>;
- 
- 				cps_clk: clock {
- 					compatible = "marvell,cp110-clock";
--- 
-2.11.0
-
board/solidrun/macchiatobin/patches/linux/0002-arm64-dts-marvell-add-comphy-nodes-on-cp110-master-a.patch deleted +0 -118

118 lines not on this page · raw message

board/solidrun/macchiatobin/patches/linux/0003-arm64-dts-marvell-mcbin-add-comphy-references-to-Eth.patch deleted +0 -58

58 lines not on this page · raw message

board/solidrun/macchiatobin/readme.txt +17 -9
index cdfe740c4e..dfbd6e793b 100644
@@ -15,8 +15,8 @@ How to build
 There are two build options: mainline support and vendor support.
 
 For the mainline BSP, we use:
- - Linux v4.14.4
- - U-Boot v2017.11
+ - Linux v4.15
+ - U-Boot v2018.01
 
 For the vendor BSP, we use the sources available from Marvell Github
 page at https://github.com/MarvellEmbeddedProcessors, which uses:
@@ -24,10 +24,10 @@ page at https://github.com/MarvellEmbeddedProcessors, which uses:
  - U-Boot v2017.03
 
 At the moment mainline support for the board is a work in progress.
-Mainline kernel 4.14 with provided patches enables eth2 in 1Gb (RJ45
-connector J5) and eth0 in 10Gb (SFP connector J15). The vendor BSP
-enables more hardware features out of the box, e.g. all the network
-interfaces.
+Mainline kernel 4.15 enables eth2 in 1Gb (RJ45 connector J5) and
+eth0 in 10Gb (SFP connector CON15 and RJ45 connector CON16).
+The vendor BSP enables more hardware features out of the box,
+e.g. all the network interfaces.
 
 To use the mainline BSP run the following commands:
 
@@ -54,13 +54,21 @@ How to boot the board
 =====================
 
 The MacchiatoBin board can be setup to load the bootloader from
-different sources including eMMC, SPI flash, and SD-card. In order to
-select boot from SD-card DIP switches SW1 and SW2 should be configured
-as follows:
+different sources including eMMC, SPI flash, and SD-card.
+
+On Rev 1.2 board to select boot from SD-card the DIP switches
+SW1 and SW2 should be configured as follows:
 
 SW2: 01110
 SW1: 1xxxx
 
+The upcoming Rev 1.3 board will have a single pins header J1 instead
+of the SW1/2 DIP switches. To boot from SD-card the setting of J1
+jumpers should match the DIP switches of Rev v1.2 board
+from left to right:
+
+J1: 011101xxxx
+
 Insert the micro SDcard in the MacchiatoBin board and power it up.
 The serial console is accessible at the micro-USB Type-B connector
 marked CON9. The serial line settings are 115200 8N1.
configs/solidrun_macchiatobin_mainline_defconfig +3 -4
index aae8e36959..526c021fe7 100644
@@ -1,6 +1,5 @@
 BR2_aarch64=y
-BR2_GLOBAL_PATCH_DIR="board/solidrun/macchiatobin/patches"
-BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_14=y
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_15=y
 BR2_TARGET_GENERIC_HOSTNAME="mcbin"
 BR2_TARGET_GENERIC_ISSUE="Welcome to Buildroot for Marvell MacchiatoBin"
 
@@ -21,12 +20,12 @@ BR2_TARGET_MV_DDR_MARVELL=y
 BR2_TARGET_UBOOT=y
 BR2_TARGET_UBOOT_BOARDNAME="mvebu_mcbin-88f8040"
 BR2_TARGET_UBOOT_CUSTOM_VERSION=y
-BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2017.11"
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2018.01"
 
 # Kernel
 BR2_LINUX_KERNEL=y
 BR2_LINUX_KERNEL_CUSTOM_VERSION=y
-BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.14.4"
+BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.15"
 BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y
 BR2_LINUX_KERNEL_DTS_SUPPORT=y
 BR2_LINUX_KERNEL_INTREE_DTS_NAME="marvell/armada-8040-mcbin"
Signature · 1 line
2.16.1
#1 lore raw

PATCH 1/1 macchiatobin: bump kernel and u-boot versions

Quoted 7 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

"Sergey" == Sergey Matyukevich <[email protected]> writes:

Bump Linux to 4.15 and U-Boot to 2018.01. Remove networking dts patches since they has landed in Linux 4.15. Update readme.txt: fix mainline BSP versions and update boot selection for board rev 1.3.

Committed, thanks.

Signature · 1 line
Bye, Peter Korsgaard