ARM: k2g: Add pinmux data for QSPI on K2G ICE
PATCH 1/2 ARM: k2g: Add pinmux data for QSPI on K2G ICE
Add pinmux for QSPI pins on K2G ICE board.
Signed-off-by Vignesh R <[email protected]>
--- board/ti/ks2_evm/mux-k2g.h | 9 +++++++++ 1 file changed, 9 insertions(+)
board/ti/ks2_evm/mux-k2g.h +9 -0
@@ -338,6 +338,15 @@ struct pin_cfg k2g_ice_evm_pin_cfg[] = {/* I2C 0 */ { 223, MODE(0) }, /* SOC_I2C0_SCL */ { 224, MODE(0) }, /* SOC_I2C0_SDA */ + +/* QSPI */ + { 129, MODE(0) }, /* SOC_QSPI_CLK */ + { 130, MODE(0) }, /* SOC_QSPI_RTCLK */ + { 131, MODE(0) }, /* SOC_QSPI_D0 */ + { 132, MODE(0) }, /* SOC_QSPI_D1 */ + { 133, MODE(0) }, /* SOC_QSPI_D2 */ + { 134, MODE(0) }, /* SOC_QSPI_D3 */ + { 135, MODE(0) }, /* SOC_QSPI_CSN0 */ { MAX_PIN_N, } };
Signature · 1 line
2.16.1
PATCH 2/2 ARM: dts: keystone-k2g-ice: Add support for QSPI
K2G ICE has a s25fl256s1 QSPI NOR flash connected to QSPI at CS0. Add DT entries for the same.
Signed-off-by Vignesh R <[email protected]>
---
Ported from linux-next.
arch/arm/dts/keystone-k2g-ice.dts | 48 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 48 insertions(+)
arch/arm/dts/keystone-k2g-ice.dts +48 -0
@@ -34,3 +34,51 @@ &i2c1 { status = "okay"; }; + +&qspi { + status = "okay"; + + flash0: m25p80 at 0 { + compatible = "s25fl256s1", "spi-flash"; + reg = <0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + spi-max-frequency = <96000000>; + #address-cells = <1>; + #size-cells = <1>; + cdns,read-delay = <5>; + cdns,tshsl-ns = <500>; + cdns,tsd2d-ns = <500>; + cdns,tchsh-ns = <119>; + cdns,tslch-ns = <119>; + + partition at 0 { + label = "QSPI.u-boot"; + reg = <0x00000000 0x00100000>; + }; + partition at 1 { + label = "QSPI.u-boot-env"; + reg = <0x00100000 0x00040000>; + }; + partition at 2 { + label = "QSPI.skern"; + reg = <0x00140000 0x0040000>; + }; + partition at 3 { + label = "QSPI.pmmc-firmware"; + reg = <0x00180000 0x0040000>; + }; + partition at 4 { + label = "QSPI.kernel"; + reg = <0x001c0000 0x0800000>; + }; + partition at 5 { + label = "QSPI.u-boot-spl-os"; + reg = <0x009c0000 0x0040000>; + }; + partition at 6 { + label = "QSPI.file-system"; + reg = <0x00a00000 0x1600000>; + }; + }; +};
Signature · 1 line
2.16.1
PATCH 2/2 ARM: dts: keystone-k2g-ice: Add support for QSPI
Quoted 4 lines · Vignesh R
K2G ICE has a s25fl256s1 QSPI NOR flash connected to QSPI at CS0. Add DT entries for the same.
Signed-off-by Vignesh R <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180208/e9ec50ac/attachment.sig>
PATCH 1/2 ARM: k2g: Add pinmux data for QSPI on K2G ICE
In reply to Vignesh RQuoted 3 lines · Vignesh R
Add pinmux for QSPI pins on K2G ICE board.
Signed-off-by Vignesh R <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: not available URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180208/a5fdb1cc/attachment.sig>