MIPS: add initial qca4531 support
PATCH 1/2 MIPS: add initial qca4531 support
The QCA4531 is a two stream (2x2) 802.11b/g/n single-band programmable Wi-Fi System-on-Chip (SoC) for the Internet of Things (IoT).
https://www.qualcomm.com/products/qca4531
Signed-off-by Oleksij Rempel <[email protected]>
--- arch/mips/dts/qca4531.dtsi | 89 ++++++++++++++++++++++ .../mach-ath79/include/mach/pbl_ll_init_qca4531.h | 70 +++++++++++++++++ 2 files changed, 159 insertions(+) create mode 100644 arch/mips/dts/qca4531.dtsi create mode 100644 arch/mips/mach-ath79/include/mach/pbl_ll_init_qca4531.h
arch/mips/dts/qca4531.dtsi new file +89 -0
@@ -0,0 +1,89 @@ +#include <dt-bindings/clock/ath79-clk.h> + +/ { + compatible = "qca,qca4531"; + + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "mips,mips24Kc"; + clocks = <&pll ATH79_CLK_CPU>; + reg = <0>; + }; + }; + + ref: ref { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + ahb { + compatible = "simple-bus"; + ranges; + + #address-cells = <1>; + #size-cells = <1>; + + apb { + compatible = "simple-bus"; + ranges; + + #address-cells = <1>; + #size-cells = <1>; + + uart0: uart@18020000 { + compatible = "ns16550a", "qca,qca4531-uart0", "qca,ar9344-uart0"; + reg = <0x18020000 0x20>; + + reg-shift = <2>; + reg-io-width = <4>; + big-endian; + + status = "disabled"; + }; + + pll: pll-controller@18050000 { + compatible = "qca,qca4531-pll"; + reg = <0x18050000 0x100>; + + clocks = <&ref>; + clock-names = "ref"; + + #clock-cells = <1>; + }; + + wdt0: wdt@18060008 { + compatible = "qca,qca4531-wdt", "qca,ar9344-wdt"; + reg = <0x18060008 0x8>; + clocks = <&pll ATH79_CLK_CPU>; + status = "disabled"; + }; + + spi: spi@1f000000 { + compatible = "qca,qca4531-spi", "qca,ar7100-spi"; + reg = <0x1f000000 0x1c>; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + }; + + mac0: mac@19000000 { + compatible = "qca,qca4531-gmac0", "qca,ar9344-gmac0"; + reg = <0x18070000 0x00000100>, + <0x19000000 0x01000000>; + reg-names = "gmac", "ge0"; + phy-mode = "rgmii"; + + status = "disabled"; + }; + }; +};
arch/mips/mach-ath79/include/mach/pbl_ll_init_qca4531.h new file +70 -0
70 lines not on this page · raw message
Signature · 7 lines
2.14.1 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 2/2 MIPS: add initial 8devices-lima board
More information about this board can be found here:
https://www.8devices.com/products/lima
Signed-off-by Oleksij Rempel <[email protected]>
--- arch/mips/Makefile | 1 + .../8devices-lima/include/board/board_pbl_start.h | 65 +++++++++++++++++ arch/mips/configs/8devices-lima_defconfig | 83 ++++++++++++++++++++++ arch/mips/dts/qca4531-8devices-lima.dts | 71 ++++++++++++++++++ arch/mips/mach-ath79/Kconfig | 8 +++ 5 files changed, 228 insertions(+) create mode 100644 arch/mips/boards/8devices-lima/include/board/board_pbl_start.h create mode 100644 arch/mips/configs/8devices-lima_defconfig create mode 100644 arch/mips/dts/qca4531-8devices-lima.dts
arch/mips/Makefile +1 -0
@@ -79,6 +79,7 @@ machine-$(CONFIG_MACH_MIPS_AR231X) := ar231x board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102 machine-$(CONFIG_MACH_MIPS_ATH79) := ath79 +board-$(CONFIG_BOARC_8DEVICES_LIMA) := 8devices-lima board-$(CONFIG_BOARC_DPTECHNICS_DPT_MODULE) := dptechnics-dpt-module board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020 board-$(CONFIG_BOARD_TPLINK_WDR4300) := tplink-wdr4300
arch/mips/boards/8devices-lima/include/board/board_pbl_start.h new file +65 -0
65 lines not on this page · raw message
arch/mips/configs/8devices-lima_defconfig new file +83 -0
83 lines not on this page · raw message
arch/mips/dts/qca4531-8devices-lima.dts new file +71 -0
71 lines not on this page · raw message
arch/mips/mach-ath79/Kconfig +8 -0
@@ -13,6 +13,14 @@ config SOC_QCA_AR9344 choice prompt "Board type" +config BOARC_8DEVICES_LIMA + bool "8devices LIMA" + select SOC_QCA_QCA4531 + select HAVE_PBL_IMAGE + select HAVE_IMAGE_COMPRESSION + select HAS_NMON + select HAS_NO_BOARD_HL_CODE + config BOARC_DPTECHNICS_DPT_MODULE bool "DPTechnics DPT-Module" select SOC_QCA_AR9331
Signature · 7 lines
2.14.1 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Sascha Hauer
AppliedQuoted 11 lines · Oleksij Rempel
The QCA4531 is a two stream (2x2) 802.11b/g/n single-band programmable Wi-Fi System-on-Chip (SoC) for the Internet of Things (IoT).
https://www.qualcomm.com/products/qca4531Signed-off-by Oleksij Rempel <[email protected]>--- arch/mips/dts/qca4531.dtsi | 89 ++++++++++++++++++++++ .../mach-ath79/include/mach/pbl_ll_init_qca4531.h | 70 +++++++++++++++++ 2 files changed, 159 insertions(+) create mode 100644 arch/mips/dts/qca4531.dtsi create mode 100644 arch/mips/mach-ath79/include/mach/pbl_ll_init_qca4531.h
Applied, thanks
Sascha
Quoted 181 lines
arch/mips/dts/qca4531.dtsi new file +89
-0@@ -0,0 +1,89 @@ +#include <dt-bindings/clock/ath79-clk.h> + +/ { + compatible = "qca,qca4531"; + + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "mips,mips24Kc"; + clocks = <&pll ATH79_CLK_CPU>; + reg = <0>; + }; + }; + + ref: ref { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + ahb { + compatible = "simple-bus"; + ranges; + + #address-cells = <1>; + #size-cells = <1>; + + apb { + compatible = "simple-bus"; + ranges; + + #address-cells = <1>; + #size-cells = <1>; + + uart0: uart@18020000 { + compatible = "ns16550a", "qca,qca4531-uart0", "qca,ar9344-uart0"; + reg = <0x18020000 0x20>; + + reg-shift = <2>; + reg-io-width = <4>; + big-endian; + + status = "disabled"; + }; + + pll: pll-controller@18050000 { + compatible = "qca,qca4531-pll"; + reg = <0x18050000 0x100>; + + clocks = <&ref>; + clock-names = "ref"; + + #clock-cells = <1>; + }; + + wdt0: wdt@18060008 { + compatible = "qca,qca4531-wdt", "qca,ar9344-wdt"; + reg = <0x18060008 0x8>; + clocks = <&pll ATH79_CLK_CPU>; + status = "disabled"; + }; + + spi: spi@1f000000 { + compatible = "qca,qca4531-spi", "qca,ar7100-spi"; + reg = <0x1f000000 0x1c>; + + #address-cells = <1>; + #size-cells = <0>; + + status = "disabled"; + }; + }; + + mac0: mac@19000000 { + compatible = "qca,qca4531-gmac0", "qca,ar9344-gmac0"; + reg = <0x18070000 0x00000100>, + <0x19000000 0x01000000>; + reg-names = "gmac", "ge0"; + phy-mode = "rgmii"; + + status = "disabled"; + }; + }; +};arch/mips/mach-ath79/include/mach/pbl_ll_init_qca4531.h new file +70
-0@@ -0,0 +1,70 @@ +#ifndef __ASM_MACH_ATH79_PBL_LL_INIT_QCA4531_H +#define __ASM_MACH_ATH79_PBL_LL_INIT_QCA4531_H + +#include <asm/addrspace.h> +#include <asm/regdef.h> + + +.macro pbl_qca4531_ddr2_550_550_init + .set push + .set noreorder + + pbl_reg_writel 0xfeceffff , 0xb806001c + pbl_reg_writel 0xeeceffff , 0xb806001c + pbl_reg_writel 0xe6ceffff , 0xb806001c + pbl_reg_writel 0x633c8176 , 0xb8116c40 + pbl_reg_writel 0x10200000 , 0xb8116c44 + pbl_reg_writel 0x4b962100 , 0xb81162c0 + pbl_reg_writel 0x480 , 0xb81162c4 + pbl_reg_writel 0x04000144 , 0xb81162c8 + pbl_reg_writel 0x54086000 , 0xb81161c4 + pbl_reg_writel 0x54086000 , 0xb8116244 + pbl_reg_writel 0x0131001c , 0xb8050008 + pbl_reg_writel 0x40001580 , 0xb8050000 + pbl_reg_writel 0x40015800 , 0xb8050004 + pbl_reg_writel 0x0131001c , 0xb8050008 + pbl_reg_writel 0x00001580 , 0xb8050000 + pbl_reg_writel 0x00015800 , 0xb8050004 + pbl_reg_writel 0x01310000 , 0xb8050008 + pbl_reg_writel 0x781003ff , 0xb8050044 + pbl_reg_writel 0x003c103f , 0xb8050048 + pbl_reg_writel 0x401f0042 , 0xb8000108 + pbl_reg_writel 0x0000166d , 0xb80000b8 + pbl_reg_writel 0xcfaaf33b , 0xb8000000 + pbl_reg_writel 0x0000000f , 0xb800015c + pbl_reg_writel 0xa272efa8 , 0xb8000004 + pbl_reg_writel 0x000ffff , 0xb8000018 + pbl_reg_writel 0x74444444 , 0xb80000c4 + pbl_reg_writel 0x00000444 , 0xb80000c8 + pbl_reg_writel 0xa210ee28 , 0xb8000004 + pbl_reg_writel 0xa2b2e1a8 , 0xb8000004 + pbl_reg_writel 0x8 , 0xb8000010 + pbl_reg_writel 0x0 , 0xb80000bc + pbl_reg_writel 0x10 , 0xb8000010 + pbl_reg_writel 0x0 , 0xb80000c0 + pbl_reg_writel 0x40 , 0xb8000010 + pbl_reg_writel 0x2 , 0xb800000c + pbl_reg_writel 0x2 , 0xb8000010 + pbl_reg_writel 0xb43 , 0xb8000008 + pbl_reg_writel 0x1 , 0xb8000010 + pbl_reg_writel 0x8 , 0xb8000010 + pbl_reg_writel 0x4 , 0xb8000010 + pbl_reg_writel 0x4 , 0xb8000010 + pbl_reg_writel 0xa43 , 0xb8000008 + pbl_reg_writel 0x1 , 0xb8000010 + pbl_reg_writel 0x382 , 0xb800000c + pbl_reg_writel 0x2 , 0xb8000010 + pbl_reg_writel 0x402 , 0xb800000c + pbl_reg_writel 0x2 , 0xb8000010 + pbl_reg_writel 0x40be , 0xb8000014 + pbl_reg_writel 0x20 , 0xb800001C + pbl_reg_writel 0x20 , 0xb8000020 + pbl_reg_writel 0xfffff , 0xb80000cc + pbl_reg_writel 0xff30b , 0xb8040000 + pbl_reg_writel 0x908 , 0xb8040044 + pbl_reg_writel 0x160000 , 0xb8040034 + + .set pop +.endm + +#endif /* __ASM_MACH_ATH79_PBL_LL_INIT_QCA4531_H */Signature · 7 lines
2.14.1 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox