Skip to contentSkip to conversation

ARM: dts: omap4-droid4: Fix USB PHY port naming

PATCH New Tony Lindgren 1 participant 2 messages Feb 17, 2018 1 message not in the archive Device tree bindings

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 ARM: dts: omap4-droid4: Fix USB PHY port naming

We have a USB OCHI PHY on port 1 for mdm6600. Port 2 is using transceiverless logic (TLL) for USB EHCI for w3glte modem.

Cc Marcel Partap <[email protected]>
Cc Michael Scott <[email protected]>
Cc Rob Herring <[email protected]>
Cc Sebastian Reichel <[email protected]>
---
 arch/arm/boot/dts/omap4-droid4-xt894.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
arch/arm/boot/dts/omap4-droid4-xt894.dts +3 -3
@@ -71,8 +71,8 @@
 		regulator-always-on;
 	};
 
-	/* HS USB Host PHY on PORT 1 */
-	hsusb1_phy: hsusb1_phy {
+	/* HS USB host TLL nop-phy on port 2 for w3glte */
+	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		#phy-cells = <0>;
 	};
@@ -584,7 +584,7 @@
 };
 
 &usbhsehci {
-	phys = <&hsusb1_phy>;
+	phys = <&hsusb2_phy>;
 };
 
 &usbhshost {
Signature · 5 lines
2.16.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

A message that is not in the archive (sent off-list or not yet received): 20180217213301.21849-1-tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org

#2 lore raw

PATCH 2/2 ARM: dts: omap4-droid4: Configure MDM6600 USB PHY

Configure MDM6600 USB PHY.

Cc Marcel Partap <[email protected]>
Cc Michael Scott <[email protected]>
Cc Sebastian Reichel <[email protected]>
---
 arch/arm/boot/dts/omap4-droid4-xt894.dts | 61 ++++++++++++++++++++++++++++++++
 1 file changed, 61 insertions(+)
arch/arm/boot/dts/omap4-droid4-xt894.dts +61 -0
@@ -71,6 +71,25 @@
 		regulator-always-on;
 	};
 
+	/* FS USB Host PHY on port 1 for mdm6600 */
+	fsusb1_phy: fsusb1_phy {
+		compatible = "motorola,mapphone-mdm6600";
+		pinctrl-0 = <&usb_mdm6600_pins>;
+		pinctrl-names = "default";
+		enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;     /* gpio_95 */
+		power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;	/* gpio_54 */
+		reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;	/* gpio_49 */
+		mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>,	/* gpio_148 */
+			     <&gpio5 21 GPIO_ACTIVE_HIGH>;	/* gpio_149 */
+		status-gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>,	/* gpio_55 */
+			       <&gpio2 21 GPIO_ACTIVE_HIGH>,	/* gpio_53 */
+			       <&gpio2 20 GPIO_ACTIVE_HIGH>;	/* gpio_52 */
+		cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>,	/* gpio_103 */
+			    <&gpio4 8 GPIO_ACTIVE_HIGH>,	/* gpio_104 */
+			    <&gpio5 14 GPIO_ACTIVE_HIGH>;	/* gpio_142 */
+		#phy-cells = <0>;
+	};
+
 	/* HS USB host TLL nop-phy on port 2 for w3glte */
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
@@ -459,6 +478,43 @@
 		>;
 	};
 
+	usb_mdm6600_pins: pinmux_usb_mdm6600_pins {
+		pinctrl-single,pins = <
+		/* enable 0x4a1000d8 usbb1_ulpitll_dat7.gpio_95 ag16 */
+		OMAP4_IOPAD(0x0d8, PIN_INPUT | MUX_MODE3)
+
+		/* power 0x4a10007c gpmc_nwp.gpio_54 c25 */
+		OMAP4_IOPAD(0x07c, PIN_OUTPUT | MUX_MODE3)
+
+		/* reset 0x4a100072 gpmc_a25.gpio_49 d20 */
+		OMAP4_IOPAD(0x072, PIN_OUTPUT | MUX_MODE3)
+
+		/* mode0/bpwake 0x4a10014e sdmmc5_dat1.gpio_148 af4 */
+		OMAP4_IOPAD(0x14e, PIN_OUTPUT | MUX_MODE3)
+
+		/* mode1/apwake 0x4a100150 sdmmc5_dat2.gpio_149 ag3 */
+		OMAP4_IOPAD(0x150, PIN_OFF_OUTPUT_LOW | PIN_INPUT | MUX_MODE3)
+
+		/* status0 0x4a10007e gpmc_clk.gpio_55 b22 */
+		OMAP4_IOPAD(0x07e, PIN_INPUT | MUX_MODE3)
+
+		/* status1 0x4a10007a gpmc_ncs3.gpio_53 c22 */
+		OMAP4_IOPAD(0x07a, PIN_INPUT | MUX_MODE3)
+
+		/* status2 0x4a100078 gpmc_ncs2.gpio_52 d21 */
+		OMAP4_IOPAD(0x078, PIN_INPUT | MUX_MODE3)
+
+		/* cmd0 0x4a100094 gpmc_ncs6.gpio_103 c24 */
+		OMAP4_IOPAD(0x094, PIN_OUTPUT | MUX_MODE3)
+
+		/* cmd1 0x4a100096 gpmc_ncs7.gpio_104 d24 */
+		OMAP4_IOPAD(0x096, PIN_OUTPUT | MUX_MODE3)
+
+		/* cmd2 0x4a100142 uart3_rts_sd.gpio_142 f28 */
+		OMAP4_IOPAD(0x142, PIN_OUTPUT | MUX_MODE3)
+		>;
+	};
+
 	usb_ulpi_pins: pinmux_usb_ulpi_pins {
 		pinctrl-single,pins = <
 		OMAP4_IOPAD(0x196, MUX_MODE7)
@@ -583,6 +639,11 @@
 	};
 };
 
+&usbhsohci {
+	phys = <&fsusb1_phy>;
+	phy-names = "usb";
+};
+
 &usbhsehci {
 	phys = <&hsusb2_phy>;
 };
Signature · 5 lines
2.16.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html