iio: light: add driver for bh1730fvc chips
Subsystems (2)
PATCH 1/1 iio: light: add driver for bh1730fvc chips
Ambient light sensor that supports visible light and IR measurements and configurable gain/integration time.
--- .../devicetree/bindings/iio/light/bh1730.txt | 15 + drivers/iio/light/Kconfig | 10 + drivers/iio/light/Makefile | 1 + drivers/iio/light/bh1730.c | 429 ++++++++++++++++++ 4 files changed, 455 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/light/bh1730.txt create mode 100644 drivers/iio/light/bh1730.c
Documentation/devicetree/bindings/iio/light/bh1730.txt new file +15 -0
@@ -0,0 +1,15 @@ +* ROHM BH1730FVC ambient light sensor + +http://www.rohm.com/web/global/products/-/product/BH1730FVC + +Required properties: + + - compatible : should be "rohm,bh1730fvc" + - reg : the I2C address of the sensor + +Example: + +bh1730fvc@29 { + compatible = "rohm,bh1730fvc"; + reg = <0x29>; +};
drivers/iio/light/Kconfig +10 -0
@@ -63,6 +63,16 @@ config APDS9960 To compile this driver as a module, choose M here: the module will be called apds9960 +config BH1730 + tristate "ROHM BH1730 ambient light sensor" + depends on I2C + help + Say Y here to build support for the ROHM BH1730FVC ambient + light sensor. + + To compile this driver as a module, choose M here: the module will + be called bh1730. + config BH1750 tristate "ROHM BH1750 ambient light sensor" depends on I2C
drivers/iio/light/Makefile +1 -0
@@ -9,6 +9,7 @@ obj-$(CONFIG_ADJD_S311) += adjd_s311.o obj-$(CONFIG_AL3320A) += al3320a.o obj-$(CONFIG_APDS9300) += apds9300.o obj-$(CONFIG_APDS9960) += apds9960.o +obj-$(CONFIG_BH1730) += bh1730.o obj-$(CONFIG_BH1750) += bh1750.o obj-$(CONFIG_BH1780) += bh1780.o obj-$(CONFIG_CM32181) += cm32181.o
drivers/iio/light/bh1730.c new file +429 -0
429 lines not on this page · raw message
Signature · 1 line
2.16.1.291.g4437f3f132-goog
Hi Pierre,
Few comments inline:
Quoted 3 lines · Pierre Bourdon
Ambient light sensor that supports visible light and IR measurements and configurable gain/integration time.
Can you have a quick look to existing ROHM light sensor support. Perhaps your sensor
is similar enough with existing code.
I'm talking about:
drivers/iio/light/{bh1750.c bh1780.c }
Quoted 21 lines
Signed-off-by Pierre Bourdon <[email protected]>--- .../devicetree/bindings/iio/light/bh1730.txt | 15 + drivers/iio/light/Kconfig | 10 + drivers/iio/light/Makefile | 1 + drivers/iio/light/bh1730.c | 429 ++++++++++++++++++ 4 files changed, 455 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/light/bh1730.txt create mode 100644 drivers/iio/light/bh1730.cDocumentation/devicetree/bindings/iio/light/bh1730.txt new file +5
-0@@ -0,0 +1,15 @@ +* ROHM BH1730FVC ambient light sensor + +http://www.rohm.com/web/global/products/-/product/BH1730FVC + +Required properties:
Documentation/devicetree/bindings/iio/light/bh1730.txt line 15
Quoted 10 lines
Documentation/devicetree/bindings/iio/light/bh1730.txt new file +10
-0+ + - compatible : should be "rohm,bh1730fvc" + - reg : the I2C address of the sensor + +Example: + +bh1730fvc@29 { + compatible = "rohm,bh1730fvc"; + reg = <0x29>; +};
Usually the devicetree binding part should be sent as a separate patch
with device-tree mailing list and maintainer at CC.
Use ./scripts/get_maintainer.pl to find the exact emails.
Mind that you should sent a patchseries:
1/2 - driver code
2/2 - documentation
Quoted 281 lines
drivers/iio/light/Kconfig +10
-0@@ -63,6 +63,16 @@ config APDS9960 To compile this driver as a module, choose M here: the module will be called apds9960 +config BH1730 + tristate "ROHM BH1730 ambient light sensor" + depends on I2C + help + Say Y here to build support for the ROHM BH1730FVC ambient + light sensor. + + To compile this driver as a module, choose M here: the module will + be called bh1730. + config BH1750 tristate "ROHM BH1750 ambient light sensor" depends on I2Cdrivers/iio/light/Makefile +1
-0@@ -9,6 +9,7 @@ obj-$(CONFIG_ADJD_S311) += adjd_s311.o obj-$(CONFIG_AL3320A) += al3320a.o obj-$(CONFIG_APDS9300) += apds9300.o obj-$(CONFIG_APDS9960) += apds9960.o +obj-$(CONFIG_BH1730) += bh1730.o obj-$(CONFIG_BH1750) += bh1750.o obj-$(CONFIG_BH1780) += bh1780.o obj-$(CONFIG_CM32181) += cm32181.odrivers/iio/light/bh1730.c new file +242
-0@@ -0,0 +1,429 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* ROHM BH1730 ambient light sensor driver +* +* Copyright (c) 2018 Google, Inc. +* Author: Pierre Bourdon <[email protected]> +* +* Based on a previous non-iio BH1730FVC driver: +* Copyright (C) 2012 Samsung Electronics. All rights reserved. +* Author: Won Huh <[email protected]> +* +* Data sheets: +* http://www.rohm.com/web/global/datasheet/BH1730FVC/bh1730fvc-e +*/ + +#include <linux/delay.h> +#include <linux/i2c.h> +#include <linux/iio/iio.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/time.h> + +#define BH1730_CMD_BIT BIT(7) + +#define BH1730_REG_CONTROL 0x00 +#define BH1730_REG_TIMING 0x01 +#define BH1730_REG_INTERRUPT 0x02 +#define BH1730_REG_THLLOW 0x03 +#define BH1730_REG_THLHIGH 0x04 +#define BH1730_REG_THHLOW 0x05 +#define BH1730_REG_THHHIGH 0x06 +#define BH1730_REG_GAIN 0x07 +#define BH1730_REG_ID 0x12 +#define BH1730_REG_DATA0LOW 0x14 +#define BH1730_REG_DATA0HIGH 0x15 +#define BH1730_REG_DATA1LOW 0x16 +#define BH1730_REG_DATA1HIGH 0x17 + +#define BH1730_CONTROL_POWER_ON BIT(0) +#define BH1730_CONTROL_MEASURE BIT(1) + +#define BH1730_INTERNAL_CLOCK_NS 2800ULL + +#define BH1730_DEFAULT_INTEG_MS 150 + +enum bh1730_gain { +BH1730_GAIN_1X =0 , +BH1730_GAIN_2X , +BH1730_GAIN_64X , +BH1730_GAIN_128X , +}; + +struct bh1730_data { +struct i2c_client *client; +enum bh1730_gain gain; +int itime; +}; + +static int bh1730_read_word (struct bh1730_data *bh1730,u8 reg) +{ +int ret =i2c_smbus_read_word_data (bh1730->client, +BH1730_CMD_BIT | reg); +if (ret <0 ) +dev_err (&bh1730->client->dev, +"i2c read failed error %d, register %01x\n" , + ret, reg); +return ret; +} + +static int bh1730_write (struct bh1730_data *bh1730,u8 reg,u8 val) +{ +int ret =i2c_smbus_write_byte_data (bh1730->client, +BH1730_CMD_BIT | reg, + val); +if (ret <0 ) +dev_err (&bh1730->client->dev, +"i2c write failed error %d, register %01x\n" , + ret, reg); +return ret; +} + +static int gain_setting_to_multiplier (enum bh1730_gain gain) +{ +switch (gain) { +case BH1730_GAIN_1X : +return 1 ; +case BH1730_GAIN_2X : +return 2 ; +case BH1730_GAIN_64X : +return 64 ; +case BH1730_GAIN_128X : +return 128 ; +default : +return -1 ; + } +} + +static int bh1730_gain_multiplier (struct bh1730_data *bh1730) +{ +int multiplier =gain_setting_to_multiplier (bh1730->gain); + +if (multiplier <0 ) { +dev_warn (&bh1730->client->dev, +"invalid gain multiplier settings: %d\n" , + bh1730->gain); + bh1730->gain =BH1730_GAIN_1X ; + multiplier =1 ; + } + +return multiplier; +} + +static u64 bh1730_itime_ns (struct bh1730_data *bh1730) +{ +return BH1730_INTERNAL_CLOCK_NS *964 * (256 - bh1730->itime); +} + +static int bh1730_set_gain (struct bh1730_data *bh1730,enum bh1730_gain gain) +{ +int ret =bh1730_write (bh1730,BH1730_REG_GAIN , gain); + +if (ret <0 ) +return ret; + + bh1730->gain = gain; +return 0 ; +} + +static int bh1730_set_integration_time_ms (struct bh1730_data *bh1730, +int time_ms) +{ +int ret; +u64 time_ns = time_ms * (u64 )NSEC_PER_MSEC ; +u64 itime_step_ns =BH1730_INTERNAL_CLOCK_NS *964 ; +int itime =256 - (int )DIV_ROUND_CLOSEST_ULL (time_ns, itime_step_ns); + +/* ITIME == 0 is reserved for manual integration mode. */ +if (itime <=0 || itime >255 ) { +dev_warn (&bh1730->client->dev, +"integration time out of range: %dms\n" , time_ms); +return -ERANGE ; + } + + ret =bh1730_write (bh1730,BH1730_REG_TIMING , itime); +if (ret <0 ) +return ret; + + bh1730->itime = itime; +return 0 ; +} + +static void bh1730_wait_for_next_measurement (struct bh1730_data *bh1730) +{ +ndelay (bh1730_itime_ns (bh1730) +BH1730_INTERNAL_CLOCK_NS *714 ); +} + +static int bh1730_adjust_gain (struct bh1730_data *bh1730) +{ +int visible, ir, highest, ret, i; + + visible =bh1730_read_word (bh1730,BH1730_REG_DATA0LOW ); +if (visible <0 ) +return visible; + + ir =bh1730_read_word (bh1730,BH1730_REG_DATA1LOW ); +if (ir <0 ) +return ir; + + highest =max (visible, ir); + +/* +* If the read value is being clamped, assume the worst and go to the +* lowest possible gain. The alternative is doing multiple +* recalibrations, which would be slower and have the same effect. +*/ +if (highest ==USHRT_MAX ) + highest *=128 ; +else + highest = (highest *128 ) /bh1730_gain_multiplier (bh1730); + +/* +* Find the lowest gain multiplier which puts the measured values +* above 1024. This threshold is chosen to match the gap between 2X +* multiplier and 64X (next available) while keeping some margin. +*/ +for (i =BH1730_GAIN_1X ; i <BH1730_GAIN_128X ; ++i) { +int adj = highest *gain_setting_to_multiplier (i) /128 ; + +if (adj >=1024 ) +break ; + } + +if (i != bh1730->gain) { + ret =bh1730_set_gain (bh1730, i); +if (ret <0 ) +return ret; + +bh1730_wait_for_next_measurement (bh1730); + } +return 0 ; +} + +static s64 bh1730_get_millilux (struct bh1730_data *bh1730) +{ +int visible, ir, visible_coef, ir_coef; +u64 itime_us =bh1730_itime_ns (bh1730) /NSEC_PER_USEC ; +u64 millilux; + + visible =bh1730_read_word (bh1730,BH1730_REG_DATA0LOW ); +if (visible <0 ) +return visible; + + ir =bh1730_read_word (bh1730,BH1730_REG_DATA1LOW ); +if (ir <0 ) +return ir; + +if (ir *1000 / visible <500 ) { + visible_coef =5002 ; + ir_coef =7502 ; + }else if (ir *1000 / visible <754 ) { + visible_coef =2250 ; + ir_coef =2000 ; + }else if (ir *1000 / visible <1029 ) { + visible_coef =1999 ; + ir_coef =1667 ; + }else if (ir *1000 / visible <1373 ) { + visible_coef =885 ; + ir_coef =583 ; + }else if (ir *1000 / visible <1879 ) { + visible_coef =309 ; + ir_coef =165 ; + }else { +return 0 ; + } + + millilux = (u64 )USEC_PER_MSEC * (visible_coef * visible - ir_coef * ir); + millilux /=bh1730_gain_multiplier (bh1730); + millilux *=103 ; + millilux /= itime_us; +return millilux; +} +
drivers/iio/light/bh1730.c line 252
Quoted 10 lines
drivers/iio/light/bh1730.c new file +10
-0+static int bh1730_power_on (struct bh1730_data *bh1730) +{ +int ret; +int control = +BH1730_CONTROL_POWER_ON | +BH1730_CONTROL_MEASURE ; + + ret =bh1730_write (bh1730,BH1730_REG_CONTROL , control); +if (ret <0 ) +return ret;
Directly return bh1730_write , remove ret and control. Similar with power_off.
Quoted 155 lines
drivers/iio/light/bh1730.c new file +155
-0+return 0 ; +} + +static int bh1730_set_defaults (struct bh1730_data *bh1730) +{ +int ret; + + ret =bh1730_set_gain (bh1730,BH1730_GAIN_1X ); +if (ret <0 ) +return ret; + + ret =bh1730_set_integration_time_ms (bh1730,BH1730_DEFAULT_INTEG_MS ); +if (ret <0 ) +return ret; + +bh1730_wait_for_next_measurement (bh1730); +return 0 ; +} + +static int bh1730_power_off (struct bh1730_data *bh1730) +{ +return bh1730_write (bh1730,BH1730_REG_CONTROL ,0 ); +} + +static int bh1730_read_raw (struct iio_dev *indio_dev, +struct iio_chan_spec const *chan, +int *val,int *val2,long mask) +{ +struct bh1730_data *bh1730 =iio_priv (indio_dev); +int ret; +s64 millilux; + + ret =bh1730_adjust_gain (bh1730); +if (ret <0 ) +return ret; + +switch (mask) { +case IIO_CHAN_INFO_PROCESSED : + millilux =bh1730_get_millilux (bh1730); +if (millilux <0 ) +return millilux; + *val = millilux /1000 ; + *val2 = (millilux %1000 ) *1000 ; +return IIO_VAL_INT_PLUS_MICRO ; +case IIO_CHAN_INFO_RAW : +switch (chan->channel2) { +case IIO_MOD_LIGHT_CLEAR : + ret =bh1730_read_word (bh1730,BH1730_REG_DATA0LOW ); +if (ret <0 ) +return ret; + *val = ret; +return IIO_VAL_INT ; +case IIO_MOD_LIGHT_IR : + ret =bh1730_read_word (bh1730,BH1730_REG_DATA1LOW ); +if (ret <0 ) +return ret; + *val = ret; +return IIO_VAL_INT ; +default : +return -EINVAL ; + } +case IIO_CHAN_INFO_SCALE : + *val =bh1730_gain_multiplier (bh1730); +return IIO_VAL_INT ; +default : +return -EINVAL ; + } +} + +static const struct iio_info bh1730_info = { + .read_raw = bh1730_read_raw, +}; + +static const struct iio_chan_spec bh1730_channels[] = { + { + .type =IIO_LIGHT , + .modified =1 , + .channel2 =IIO_MOD_LIGHT_BOTH , + .info_mask_separate =BIT (IIO_CHAN_INFO_PROCESSED ), + }, + { + .type =IIO_LIGHT , + .modified =1 , + .channel2 =IIO_MOD_LIGHT_CLEAR , + .info_mask_separate =BIT (IIO_CHAN_INFO_RAW ) | +BIT (IIO_CHAN_INFO_SCALE ), + }, + { + .type =IIO_LIGHT , + .modified =1 , + .channel2 =IIO_MOD_LIGHT_IR , + .info_mask_separate =BIT (IIO_CHAN_INFO_RAW ) | +BIT (IIO_CHAN_INFO_SCALE ), + }, +}; + +static int bh1730_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +struct bh1730_data *bh1730; +struct i2c_adapter *adapter =to_i2c_adapter (client->dev.parent); +struct iio_dev *indio_dev; +int ret; + +if (!i2c_check_functionality (adapter,I2C_FUNC_SMBUS_BYTE )) +return -EIO ; + + indio_dev =devm_iio_device_alloc (&client->dev,sizeof (*bh1730)); +if (!indio_dev) +return -ENOMEM ; + + bh1730 =iio_priv (indio_dev); + bh1730->client = client; +i2c_set_clientdata (client, indio_dev); + + ret =bh1730_power_on (bh1730); +if (ret <0 ) +return ret; + + ret =bh1730_set_defaults (bh1730); +if (ret <0 ) +return ret; + + indio_dev->dev.parent = &client->dev; + indio_dev->info = &bh1730_info; + indio_dev->name ="bh1730" ; + indio_dev->channels = bh1730_channels; + indio_dev->num_channels =ARRAY_SIZE (bh1730_channels); + indio_dev->modes =INDIO_DIRECT_MODE ; + + ret =iio_device_register (indio_dev); +if (ret) + goto out_power_off; +return 0 ; + +out_power_off: +bh1730_power_off (bh1730); +return ret; +} + +static int bh1730_remove (struct i2c_client *client) +{ +struct iio_dev *indio_dev =i2c_get_clientdata (client); +struct bh1730_data *bh1730 =iio_priv (indio_dev); + +iio_device_unregister (indio_dev); +return bh1730_power_off (bh1730); +} + +static const struct i2c_device_id bh1730_id[] = { + {"bh1730" ,0 }, + {}, +}; +MODULE_DEVICE_TABLE (i2c, bh1730_id); +
drivers/iio/light/bh1730.c line 417
Quoted 10 lines
drivers/iio/light/bh1730.c new file +10
-0+#ifdef CONFIG_OF +static const struct of_device_id of_bh1730_match[] = { + { .compatible ="rohm,bh1730fvc" }, + {}, +}; +MODULE_DEVICE_TABLE (of, of_bh1730_match); +#endif + +static struct i2c_driver bh1730_driver = { + .probe = bh1730_probe,
I wonder if you can use the probe_new API here.
e.g
Quoted 13 lines
drivers/iio/light/bh1730.c new file +12
-0+ .remove = bh1730_remove, + .id_table = bh1730_id, + .driver = { + .name = "bh1730", + .of_match_table = of_match_ptr(of_bh1730_match), + }, +}; +module_i2c_driver (bh1730_driver); + +MODULE_AUTHOR ("Pierre Bourdon <[email protected]>" ); +MODULE_DESCRIPTION ("ROHM BH1730FVC driver" ); +MODULE_LICENSE ("GPL v2" );
Hi Daniel,
Quoted 5 lines · Daniel Baluta
Quoted 3 lines · Pierre Bourdon
Ambient light sensor that supports visible light and IR measurements and configurable gain/integration time.
Quoted 7 lines
Can you have a quick look to existing ROHM light sensor support. Perhaps your sensor
is similar enough with existing code.I'm talking about:
drivers/iio/light/{bh1750.cbh1780.c}
bh1750 does things sufficiently different in its protocol that the amount of common code would be fairly small. Unlike bh1730/bh1780 it's not fully SMBus compatible for example.
bh1780 could probably be implemented as a subset of bh1730. It's basically a simplified bh1730 with less knobs. But there is still a significant amount of differences that make common code difficult to extract. For example, bh1780 reads lux values directly from the chip, whereas bh1730 has two raw channels that need to be combined in software to get a processed lux value. It could be done, but my gut feeling is that writing a "HAL" for this is going to make things more complicated, not simpler.
My experience in this domain is close to zero, so I'm completely open to giving it a try if you think merging these two makes sense.
Quoted 35 lines
Quoted 21 lines
Signed-off-by Pierre Bourdon <[email protected]>--- .../devicetree/bindings/iio/light/bh1730.txt | 15 + drivers/iio/light/Kconfig | 10 + drivers/iio/light/Makefile | 1 + drivers/iio/light/bh1730.c | 429 ++++++++++++++++++ 4 files changed, 455 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/light/bh1730.txt create mode 100644 drivers/iio/light/bh1730.cDocumentation/devicetree/bindings/iio/light/bh1730.txt new file +5
-0@@ -0,0 +1,15 @@ +* ROHM BH1730FVC ambient light sensor + +http://www.rohm.com/web/global/products/-/product/BH1730FVC + +Required properties:Documentation/devicetree/bindings/iio/light/bh1730.txt line 15
Quoted 10 lines
Documentation/devicetree/bindings/iio/light/bh1730.txt new file +10
-0+ + - compatible : should be "rohm,bh1730fvc" + - reg : the I2C address of the sensor + +Example: + +bh1730fvc@29 { + compatible = "rohm,bh1730fvc"; + reg = <0x29>; +};Usually the devicetree binding part should be sent as a separate patch
with device-tree mailing list and maintainer at CC.
Quoted 6 lines
Use
./scripts/get_maintainer.plto find the exact emails.Mind that you should sent a patchseries:
1/2 - driver code
2/2 - documentation
Will do. Should the of_match_table in the driver code be part of 1/2 (driver) or 2/2 (dt-bindings)?
I'll send a v2 with this + the other changes you've suggested.
Thanks!
Quoted 478 lines
Quoted 281 lines
drivers/iio/light/Kconfig +10
-0@@ -63,6 +63,16 @@ config APDS9960 To compile this driver as a module, choose M here: the module will be called apds9960 +config BH1730 + tristate "ROHM BH1730 ambient light sensor" + depends on I2C + help + Say Y here to build support for the ROHM BH1730FVC ambient + light sensor. + + To compile this driver as a module, choose M here: the module will + be called bh1730. + config BH1750 tristate "ROHM BH1750 ambient light sensor" depends on I2Cdrivers/iio/light/Makefile +1
-0@@ -9,6 +9,7 @@ obj-$(CONFIG_ADJD_S311) += adjd_s311.o obj-$(CONFIG_AL3320A) += al3320a.o obj-$(CONFIG_APDS9300) += apds9300.o obj-$(CONFIG_APDS9960) += apds9960.o +obj-$(CONFIG_BH1730) += bh1730.o obj-$(CONFIG_BH1750) += bh1750.o obj-$(CONFIG_BH1780) += bh1780.o obj-$(CONFIG_CM32181) += cm32181.odrivers/iio/light/bh1730.c new file +242
-0@@ -0,0 +1,429 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* ROHM BH1730 ambient light sensor driver +* +* Copyright (c) 2018 Google, Inc. +* Author: Pierre Bourdon <[email protected]> +* +* Based on a previous non-iio BH1730FVC driver: +* Copyright (C) 2012 Samsung Electronics. All rights reserved. +* Author: Won Huh <[email protected]> +* +* Data sheets: +* http://www.rohm.com/web/global/datasheet/BH1730FVC/bh1730fvc-e +*/ + +#include <linux/delay.h> +#include <linux/i2c.h> +#include <linux/iio/iio.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/time.h> + +#define BH1730_CMD_BIT BIT(7) + +#define BH1730_REG_CONTROL 0x00 +#define BH1730_REG_TIMING 0x01 +#define BH1730_REG_INTERRUPT 0x02 +#define BH1730_REG_THLLOW 0x03 +#define BH1730_REG_THLHIGH 0x04 +#define BH1730_REG_THHLOW 0x05 +#define BH1730_REG_THHHIGH 0x06 +#define BH1730_REG_GAIN 0x07 +#define BH1730_REG_ID 0x12 +#define BH1730_REG_DATA0LOW 0x14 +#define BH1730_REG_DATA0HIGH 0x15 +#define BH1730_REG_DATA1LOW 0x16 +#define BH1730_REG_DATA1HIGH 0x17 + +#define BH1730_CONTROL_POWER_ON BIT(0) +#define BH1730_CONTROL_MEASURE BIT(1) + +#define BH1730_INTERNAL_CLOCK_NS 2800ULL + +#define BH1730_DEFAULT_INTEG_MS 150 + +enum bh1730_gain { +BH1730_GAIN_1X =0 , +BH1730_GAIN_2X , +BH1730_GAIN_64X , +BH1730_GAIN_128X , +}; + +struct bh1730_data { +struct i2c_client *client; +enum bh1730_gain gain; +int itime; +}; + +static int bh1730_read_word (struct bh1730_data *bh1730,u8 reg) +{ +int ret =i2c_smbus_read_word_data (bh1730->client, +BH1730_CMD_BIT | reg); +if (ret <0 ) +dev_err (&bh1730->client->dev, +"i2c read failed error %d, register %01x\n" , + ret, reg); +return ret; +} + +static int bh1730_write (struct bh1730_data *bh1730,u8 reg,u8 val) +{ +int ret =i2c_smbus_write_byte_data (bh1730->client, +BH1730_CMD_BIT | reg, + val); +if (ret <0 ) +dev_err (&bh1730->client->dev, +"i2c write failed error %d, register %01x\n" , + ret, reg); +return ret; +} + +static int gain_setting_to_multiplier (enum bh1730_gain gain) +{ +switch (gain) { +case BH1730_GAIN_1X : +return 1 ; +case BH1730_GAIN_2X : +return 2 ; +case BH1730_GAIN_64X : +return 64 ; +case BH1730_GAIN_128X : +return 128 ; +default : +return -1 ; + } +} + +static int bh1730_gain_multiplier (struct bh1730_data *bh1730) +{ +int multiplier =gain_setting_to_multiplier (bh1730->gain); + +if (multiplier <0 ) { +dev_warn (&bh1730->client->dev, +"invalid gain multiplier settings: %d\n" , + bh1730->gain); + bh1730->gain =BH1730_GAIN_1X ; + multiplier =1 ; + } + +return multiplier; +} + +static u64 bh1730_itime_ns (struct bh1730_data *bh1730) +{ +return BH1730_INTERNAL_CLOCK_NS *964 * (256 - bh1730->itime); +} + +static int bh1730_set_gain (struct bh1730_data *bh1730,enum bh1730_gain gain) +{ +int ret =bh1730_write (bh1730,BH1730_REG_GAIN , gain); + +if (ret <0 ) +return ret; + + bh1730->gain = gain; +return 0 ; +} + +static int bh1730_set_integration_time_ms (struct bh1730_data *bh1730, +int time_ms) +{ +int ret; +u64 time_ns = time_ms * (u64 )NSEC_PER_MSEC ; +u64 itime_step_ns =BH1730_INTERNAL_CLOCK_NS *964 ; +int itime =256 - (int )DIV_ROUND_CLOSEST_ULL (time_ns, itime_step_ns); + +/* ITIME == 0 is reserved for manual integration mode. */ +if (itime <=0 || itime >255 ) { +dev_warn (&bh1730->client->dev, +"integration time out of range: %dms\n" , time_ms); +return -ERANGE ; + } + + ret =bh1730_write (bh1730,BH1730_REG_TIMING , itime); +if (ret <0 ) +return ret; + + bh1730->itime = itime; +return 0 ; +} + +static void bh1730_wait_for_next_measurement (struct bh1730_data *bh1730) +{ +ndelay (bh1730_itime_ns (bh1730) +BH1730_INTERNAL_CLOCK_NS *714 ); +} + +static int bh1730_adjust_gain (struct bh1730_data *bh1730) +{ +int visible, ir, highest, ret, i; + + visible =bh1730_read_word (bh1730,BH1730_REG_DATA0LOW ); +if (visible <0 ) +return visible; + + ir =bh1730_read_word (bh1730,BH1730_REG_DATA1LOW ); +if (ir <0 ) +return ir; + + highest =max (visible, ir); + +/* +* If the read value is being clamped, assume the worst and go to the +* lowest possible gain. The alternative is doing multiple +* recalibrations, which would be slower and have the same effect. +*/ +if (highest ==USHRT_MAX ) + highest *=128 ; +else + highest = (highest *128 ) /bh1730_gain_multiplier (bh1730); + +/* +* Find the lowest gain multiplier which puts the measured values +* above 1024. This threshold is chosen to match the gap between 2X +* multiplier and 64X (next available) while keeping some margin. +*/ +for (i =BH1730_GAIN_1X ; i <BH1730_GAIN_128X ; ++i) { +int adj = highest *gain_setting_to_multiplier (i) /128 ; + +if (adj >=1024 ) +break ; + } + +if (i != bh1730->gain) { + ret =bh1730_set_gain (bh1730, i); +if (ret <0 ) +return ret; + +bh1730_wait_for_next_measurement (bh1730); + } +return 0 ; +} + +static s64 bh1730_get_millilux (struct bh1730_data *bh1730) +{ +int visible, ir, visible_coef, ir_coef; +u64 itime_us =bh1730_itime_ns (bh1730) /NSEC_PER_USEC ; +u64 millilux; + + visible =bh1730_read_word (bh1730,BH1730_REG_DATA0LOW ); +if (visible <0 ) +return visible; + + ir =bh1730_read_word (bh1730,BH1730_REG_DATA1LOW ); +if (ir <0 ) +return ir; + +if (ir *1000 / visible <500 ) { + visible_coef =5002 ; + ir_coef =7502 ; + }else if (ir *1000 / visible <754 ) { + visible_coef =2250 ; + ir_coef =2000 ; + }else if (ir *1000 / visible <1029 ) { + visible_coef =1999 ; + ir_coef =1667 ; + }else if (ir *1000 / visible <1373 ) { + visible_coef =885 ; + ir_coef =583 ; + }else if (ir *1000 / visible <1879 ) { + visible_coef =309 ; + ir_coef =165 ; + }else { +return 0 ; + } + + millilux = (u64 )USEC_PER_MSEC * (visible_coef * visible - ir_coef * ir); + millilux /=bh1730_gain_multiplier (bh1730); + millilux *=103 ; + millilux /= itime_us; +return millilux; +} +drivers/iio/light/bh1730.c line 252
Quoted 10 lines
drivers/iio/light/bh1730.c new file +10
-0+static int bh1730_power_on (struct bh1730_data *bh1730) +{ +int ret; +int control = +BH1730_CONTROL_POWER_ON | +BH1730_CONTROL_MEASURE ; + + ret =bh1730_write (bh1730,BH1730_REG_CONTROL , control); +if (ret <0 ) +return ret;Directly return
bh1730_write, remove ret and control. Similar withpower_off.Quoted 155 lines
drivers/iio/light/bh1730.c new file +155
-0+return 0 ; +} + +static int bh1730_set_defaults (struct bh1730_data *bh1730) +{ +int ret; + + ret =bh1730_set_gain (bh1730,BH1730_GAIN_1X ); +if (ret <0 ) +return ret; + + ret =bh1730_set_integration_time_ms (bh1730,BH1730_DEFAULT_INTEG_MS ); +if (ret <0 ) +return ret; + +bh1730_wait_for_next_measurement (bh1730); +return 0 ; +} + +static int bh1730_power_off (struct bh1730_data *bh1730) +{ +return bh1730_write (bh1730,BH1730_REG_CONTROL ,0 ); +} + +static int bh1730_read_raw (struct iio_dev *indio_dev, +struct iio_chan_spec const *chan, +int *val,int *val2,long mask) +{ +struct bh1730_data *bh1730 =iio_priv (indio_dev); +int ret; +s64 millilux; + + ret =bh1730_adjust_gain (bh1730); +if (ret <0 ) +return ret; + +switch (mask) { +case IIO_CHAN_INFO_PROCESSED : + millilux =bh1730_get_millilux (bh1730); +if (millilux <0 ) +return millilux; + *val = millilux /1000 ; + *val2 = (millilux %1000 ) *1000 ; +return IIO_VAL_INT_PLUS_MICRO ; +case IIO_CHAN_INFO_RAW : +switch (chan->channel2) { +case IIO_MOD_LIGHT_CLEAR : + ret =bh1730_read_word (bh1730,BH1730_REG_DATA0LOW ); +if (ret <0 ) +return ret; + *val = ret; +return IIO_VAL_INT ; +case IIO_MOD_LIGHT_IR : + ret =bh1730_read_word (bh1730,BH1730_REG_DATA1LOW ); +if (ret <0 ) +return ret; + *val = ret; +return IIO_VAL_INT ; +default : +return -EINVAL ; + } +case IIO_CHAN_INFO_SCALE : + *val =bh1730_gain_multiplier (bh1730); +return IIO_VAL_INT ; +default : +return -EINVAL ; + } +} + +static const struct iio_info bh1730_info = { + .read_raw = bh1730_read_raw, +}; + +static const struct iio_chan_spec bh1730_channels[] = { + { + .type =IIO_LIGHT , + .modified =1 , + .channel2 =IIO_MOD_LIGHT_BOTH , + .info_mask_separate =BIT (IIO_CHAN_INFO_PROCESSED ), + }, + { + .type =IIO_LIGHT , + .modified =1 , + .channel2 =IIO_MOD_LIGHT_CLEAR , + .info_mask_separate =BIT (IIO_CHAN_INFO_RAW ) | +BIT (IIO_CHAN_INFO_SCALE ), + }, + { + .type =IIO_LIGHT , + .modified =1 , + .channel2 =IIO_MOD_LIGHT_IR , + .info_mask_separate =BIT (IIO_CHAN_INFO_RAW ) | +BIT (IIO_CHAN_INFO_SCALE ), + }, +}; + +static int bh1730_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +struct bh1730_data *bh1730; +struct i2c_adapter *adapter =to_i2c_adapter (client->dev.parent); +struct iio_dev *indio_dev; +int ret; + +if (!i2c_check_functionality (adapter,I2C_FUNC_SMBUS_BYTE )) +return -EIO ; + + indio_dev =devm_iio_device_alloc (&client->dev,sizeof (*bh1730)); +if (!indio_dev) +return -ENOMEM ; + + bh1730 =iio_priv (indio_dev); + bh1730->client = client; +i2c_set_clientdata (client, indio_dev); + + ret =bh1730_power_on (bh1730); +if (ret <0 ) +return ret; + + ret =bh1730_set_defaults (bh1730); +if (ret <0 ) +return ret; + + indio_dev->dev.parent = &client->dev; + indio_dev->info = &bh1730_info; + indio_dev->name ="bh1730" ; + indio_dev->channels = bh1730_channels; + indio_dev->num_channels =ARRAY_SIZE (bh1730_channels); + indio_dev->modes =INDIO_DIRECT_MODE ; + + ret =iio_device_register (indio_dev); +if (ret) + goto out_power_off; +return 0 ; + +out_power_off: +bh1730_power_off (bh1730); +return ret; +} + +static int bh1730_remove (struct i2c_client *client) +{ +struct iio_dev *indio_dev =i2c_get_clientdata (client); +struct bh1730_data *bh1730 =iio_priv (indio_dev); + +iio_device_unregister (indio_dev); +return bh1730_power_off (bh1730); +} + +static const struct i2c_device_id bh1730_id[] = { + {"bh1730" ,0 }, + {}, +}; +MODULE_DEVICE_TABLE (i2c, bh1730_id); +drivers/iio/light/bh1730.c line 417
Quoted 10 lines
drivers/iio/light/bh1730.c new file +10
-0+#ifdef CONFIG_OF +static const struct of_device_id of_bh1730_match[] = { + { .compatible ="rohm,bh1730fvc" }, + {}, +}; +MODULE_DEVICE_TABLE (of, of_bh1730_match); +#endif + +static struct i2c_driver bh1730_driver = { + .probe = bh1730_probe,I wonder if you can use the
probe_newAPI here.e.g
Quoted 13 lines
drivers/iio/light/bh1730.c new file +12
-0+ .remove = bh1730_remove, + .id_table = bh1730_id, + .driver = { + .name = "bh1730", + .of_match_table = of_match_ptr(of_bh1730_match), + }, +}; +module_i2c_driver (bh1730_driver); + +MODULE_AUTHOR ("Pierre Bourdon <[email protected]>" ); +MODULE_DESCRIPTION ("ROHM BH1730FVC driver" ); +MODULE_LICENSE ("GPL v2" );
Signature · 1 line
Pierre Bourdon (delroth@)
Quoted 20 lines · Pierre Bourdon (delroth)
Hi Daniel,
Quoted 5 lines · Daniel Baluta
Quoted 3 lines · Pierre Bourdon
Ambient light sensor that supports visible light and IR measurements and configurable gain/integration time.
Quoted 7 lines
Can you have a quick look to existing ROHM light sensor support. Perhaps your sensor
is similar enough with existing code.I'm talking about:
drivers/iio/light/{bh1750.cbh1780.c}bh1750 does things sufficiently different in its protocol that the amount of common code would be fairly small. Unlike bh1730/bh1780 it's not fully SMBus compatible for example.
Quoted 9 lines
bh1780 could probably be implemented as a subset of bh1730. It's basically a simplified bh1730 with less knobs. But there is still a significant amount of differences that make common code difficult to extract. For example, bh1780 reads lux values directly from the chip, whereas bh1730 has two raw channels that need to be combined in software to get a processed lux value. It could be done, but my gut feeling is that writing a "HAL" for this is going to make things more complicated, not simpler.
I only had a very quick look at existing ROHM sensors drivers. So, sure if it doesn't makes sense then we can have bh1730 as a standalone driver.
<snip>
Quoted 6 lines
Quoted 6 lines
Usually the devicetree binding part should be sent as a separate patch
with device-tree mailing list and maintainer at CC.Use
./scripts/get_maintainer.plto find the exact emails.
Quoted 8 lines
Quoted 4 lines
Mind that you should sent a patchseries:
1/2 - driver code
2/2 - documentationWill do. Should the
of_match_tablein the driver code be part of 1/2 (driver) or 2/2 (dt-bindings)?
Should be part of 1/2. 2/2 should only containt the patch for Documentation.
Quoted 1 line
I'll send a v2 with this + the other changes you've suggested.
Great thanks!
Any idea how to make my gmail not to wrap the lines in plain text mode? :D It drives me crazy when I reread my emails.
thanks,
Daniel.
PATCH v2 1/2 iio: light: add driver for bh1730fvc chips
In reply to Pierre BourdonAmbient light sensor that supports visible light and IR measurements and configurable gain/integration time.
Changed in v2:
* Split off DT documentation change into a separate commit.
* Use i2c's probe_new.
--- drivers/iio/light/Kconfig | 10 + drivers/iio/light/Makefile | 1 + drivers/iio/light/bh1730.c | 414 +++++++++++++++++++++++++++++++++++++ 3 files changed, 425 insertions(+) create mode 100644 drivers/iio/light/bh1730.c
drivers/iio/light/Kconfig +10 -0
@@ -63,6 +63,16 @@ config APDS9960 To compile this driver as a module, choose M here: the module will be called apds9960 +config BH1730 + tristate "ROHM BH1730 ambient light sensor" + depends on I2C + help + Say Y here to build support for the ROHM BH1730FVC ambient + light sensor. + + To compile this driver as a module, choose M here: the module will + be called bh1730. + config BH1750 tristate "ROHM BH1750 ambient light sensor" depends on I2C
drivers/iio/light/Makefile +1 -0
@@ -9,6 +9,7 @@ obj-$(CONFIG_ADJD_S311) += adjd_s311.o obj-$(CONFIG_AL3320A) += al3320a.o obj-$(CONFIG_APDS9300) += apds9300.o obj-$(CONFIG_APDS9960) += apds9960.o +obj-$(CONFIG_BH1730) += bh1730.o obj-$(CONFIG_BH1750) += bh1750.o obj-$(CONFIG_BH1780) += bh1780.o obj-$(CONFIG_CM32181) += cm32181.o
drivers/iio/light/bh1730.c new file +414 -0
414 lines not on this page · raw message
Signature · 1 line
2.16.1.291.g4437f3f132-goog
PATCH v2 2/2 dt-bindings: iio: light: Add bh1730fvc bindings
--- .../devicetree/bindings/iio/light/bh1730.txt | 15 +++++++++++++++ 1 file changed, 15 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/light/bh1730.txt
Documentation/devicetree/bindings/iio/light/bh1730.txt new file +15 -0
@@ -0,0 +1,15 @@ +* ROHM BH1730FVC ambient light sensor + +http://www.rohm.com/web/global/products/-/product/BH1730FVC + +Required properties: + + - compatible : should be "rohm,bh1730fvc" + - reg : the I2C address of the sensor + +Example: + +bh1730fvc@29 { + compatible = "rohm,bh1730fvc"; + reg = <0x29>; +};
Signature · 1 line
2.16.1.291.g4437f3f132-goog
Quoted 6 lines · Pierre Bourdon
Ambient light sensor that supports visible light and IR measurements and configurable gain/integration time.
Changed in v2:
* Split off DT documentation change into a separate commit.
* Use i2c'sprobe_new.
Btw, how big the difference with existing drivers?
drivers/iio/light/bh1730.c line 94
Quoted 2 lines
drivers/iio/light/bh1730.c new file +2
-0+default : +return -1 ;
Better to
return -EINVAL;
drivers/iio/light/bh1730.c line 179
Quoted 11 lines
drivers/iio/light/bh1730.c new file +11
-0+ highest =max (visible, ir); + +/* +* If the read value is being clamped, assume the worst and go to the +* lowest possible gain. The alternative is doing multiple +* recalibrations, which would be slower and have the same effect. +*/ +if (highest ==USHRT_MAX ) + highest *=128 ; +else + highest = (highest *128 ) /bh1730_gain_multiplier (bh1730);
In both cases you multiply.
Why not just
highest = max(visible, ir) * 128;
if (highest < USHRT_MAX)
...
?
Quoted 1 line
+ millilux = (u64)USEC_PER_MSEC * (
visible_coef* visible -ir_coef* ir);
I'm not sure I understand how time units is related to lux one.
drivers/iio/light/bh1730.c line 368
Quoted 12 lines
drivers/iio/light/bh1730.c new file +10
-0+ millilux /=bh1730_gain_multiplier (bh1730); + millilux *=103 ; + millilux /= itime_us; +return millilux; +} + indio_dev =devm_iio_device_alloc (&client->dev,sizeof (*bh1730)); +if (!indio_dev) +return -ENOMEM ; + + indio_dev->dev.parent = &client->dev;
Strange, it's not done in IIO core... Jonathan, is it true that in case of devm_iio_device_alloc() all drivers use supplied struct device as a parent one?
If so, doesn't make sense to modify IIO core to do this?
drivers/iio/light/bh1730.c line 390
Quoted 7 lines
drivers/iio/light/bh1730.c new file +6
-0+static int bh1730_remove (struct i2c_client *client) +{ +struct iio_dev *indio_dev =i2c_get_clientdata (client); +struct bh1730_data *bh1730 =iio_priv (indio_dev); + +iio_device_unregister (indio_dev);
Hmm... Do you still need this even with devm IIO in ->probe()?
drivers/iio/light/bh1730.c line 400
Quoted 2 lines
drivers/iio/light/bh1730.c new file +2
-0+#ifdef CONFIG_OF +#endif
This...
Quoted 1 line
+ .of_match_table =
of_match_ptr(of_bh1730_match),
...and of_match_ptr() now pointless.
Signature · 2 lines
With Best Regards, Andy Shevchenko
Hi Andy,
Thanks for the review! Answers inline. I'll send a v3 when the two open questions are resolved.
Quoted 9 lines · Andy Shevchenko
Quoted 6 lines · Pierre Bourdon
Ambient light sensor that supports visible light and IR measurements and configurable gain/integration time.
Changed in v2:
* Split off DT documentation change into a separate commit.
* Use i2c'sprobe_new.Btw, how big the difference with existing drivers?
See https://lkml.org/lkml/2018/2/21/982 . In retrospect, I should have added this to the commit message. It will be there in v3.
Quoted 12 lines
drivers/iio/light/bh1730.c line 179
Quoted 11 lines
drivers/iio/light/bh1730.c new file +11
-0+ highest =max (visible, ir); + +/* +* If the read value is being clamped, assume the worst and go to the +* lowest possible gain. The alternative is doing multiple +* recalibrations, which would be slower and have the same effect. +*/ +if (highest ==USHRT_MAX ) + highest *=128 ; +else + highest = (highest *128 ) /bh1730_gain_multiplier (bh1730);
Quoted 8 lines
In both cases you multiply.
Why not justhighest = max(visible, ir) * 128;if (highest <
USHRT_MAX)
...
?
You'd need < USHRT_MAX * 128 then. I refactored this a bit but differently. WDYT?
if (highest == USHRT_MAX)
gain = 1;
else
gain = bh1730_gain_multiplier(bh1730);
highest = (highest * BH1730_MAX_GAIN_MULTIPLIER) / gain;Quoted 3 lines
Quoted 1 line
+ millilux = (u64)USEC_PER_MSEC * (
visible_coef* visible -ir_coef* ir);I'm not sure I understand how time units is related to lux one.
Now looks like this, which should match the units together better while keeping most multiplications before divisions (for accuracy). Not much better I can do here I think, for example the magic "103" is straight from the datasheet with no explanation.
millilux = visible_coef * visible - ir_coef * ir;
millilux = (millilux * USEC_PER_MSEC) / itime_us;
millilux *= 103;
millilux /= bh1730_gain_multiplier(bh1730);Quoted 11 lines
drivers/iio/light/bh1730.c line 368
Quoted 6 lines
drivers/iio/light/bh1730.c new file +5
-0+ indio_dev =devm_iio_device_alloc (&client->dev,sizeof (*bh1730)); +if (!indio_dev) +return -ENOMEM ; + + indio_dev->dev.parent = &client->dev;Strange, it's not done in IIO core... Jonathan, is it true that in case of
devm_iio_device_alloc()all drivers use supplied struct device as a parent one?
If so, doesn't make sense to modify IIO core to do this?
It doesn't seem like IIO core is doing it at this point. Should we just leave that as-is for now and get everything fixed in a future patch?
Quoted 9 lines
drivers/iio/light/bh1730.c line 390
Quoted 7 lines
drivers/iio/light/bh1730.c new file +6
-0+static int bh1730_remove (struct i2c_client *client) +{ +struct iio_dev *indio_dev =i2c_get_clientdata (client); +struct bh1730_data *bh1730 =iio_priv (indio_dev); + +iio_device_unregister (indio_dev);Hmm... Do you still need this even with devm IIO in ->probe()?
I *think* so, but that's mostly because all the other IIO light drivers that I've looked at are doing it. Can someone who knows the IIO subsystem well weigh in?
Thanks!
Best,
Signature · 1 line
Pierre Bourdon (delroth@)
Jonathan Cameron
maintainerQuoted 72 lines · On Thu, 22 Feb 2018 15:58:10 +0100 "Pierre Bourdon (delroth)"…
Hi Andy,
Thanks for the review! Answers inline. I'll send a v3 when the two open questions are resolved.
Quoted 9 lines · Andy Shevchenko
Quoted 6 lines · Pierre Bourdon
Ambient light sensor that supports visible light and IR measurements and configurable gain/integration time.
Changed in v2:
* Split off DT documentation change into a separate commit.
* Use i2c'sprobe_new.Btw, how big the difference with existing drivers?
See https://lkml.org/lkml/2018/2/21/982 . In retrospect, I should have added this to the commit message. It will be there in v3.
Quoted 12 lines
drivers/iio/light/bh1730.c line 179
Quoted 11 lines
drivers/iio/light/bh1730.c new file +11
-0+ highest =max (visible, ir); + +/* +* If the read value is being clamped, assume the worst and go to the +* lowest possible gain. The alternative is doing multiple +* recalibrations, which would be slower and have the same effect. +*/ +if (highest ==USHRT_MAX ) + highest *=128 ; +else + highest = (highest *128 ) /bh1730_gain_multiplier (bh1730);Quoted 8 lines
In both cases you multiply.
Why not justhighest = max(visible, ir) * 128;if (highest <
USHRT_MAX)
...
?You'd need <
USHRT_MAX* 128 then. I refactored this a bit but differently. WDYT?if (highest == USHRT_MAX) gain = 1; else gain = bh1730_gain_multiplier(bh1730); highest = (highest * BH1730_MAX_GAIN_MULTIPLIER) / gain;Quoted 3 lines
Quoted 1 line
+ millilux = (u64)USEC_PER_MSEC * (
visible_coef* visible -ir_coef* ir);I'm not sure I understand how time units is related to lux one.
Now looks like this, which should match the units together better while keeping most multiplications before divisions (for accuracy). Not much better I can do here I think, for example the magic "103" is straight from the datasheet with no explanation.
millilux = visible_coef * visible - ir_coef * ir; millilux = (millilux * USEC_PER_MSEC) / itime_us; millilux *= 103; millilux /= bh1730_gain_multiplier(bh1730);Quoted 7 lines
Quoted 6 lines
drivers/iio/light/bh1730.c new file +5
-0+ indio_dev =devm_iio_device_alloc (&client->dev,sizeof (*bh1730)); +if (!indio_dev) +return -ENOMEM ; + + indio_dev->dev.parent = &client->dev;
Quoted 8 lines
Quoted 4 lines
Strange, it's not done in IIO core... Jonathan, is it true that in case of
devm_iio_device_alloc()all drivers use supplied struct device as a parent one?
If so, doesn't make sense to modify IIO core to do this?It doesn't seem like IIO core is doing it at this point. Should we just leave that as-is for now and get everything fixed in a future patch?
It's an interesting point - the bit that bothers me about rolling that into the devm_iio_device_alloc is that it then means that function is doing something a little non-obvious given we don't have the relevant struct device available in the iio_device_alloc call case.
However, we only have two iio_device_alloc calls left. The dummy driver one doesn't have a parent (hardly surprising as there is no hardware).
The other is harder to argue as it's inside the toshiba acpi driver where reworking to make devm possible would be a major job.
Hmm. Will think about it...
Quoted 7 lines
Quoted 7 lines
Quoted 6 lines
drivers/iio/light/bh1730.c new file +5
-0+static int bh1730_remove (struct i2c_client *client) +{ +struct iio_dev *indio_dev =i2c_get_clientdata (client); +struct bh1730_data *bh1730 =iio_priv (indio_dev); +
Quoted 7 lines
Quoted 3 lines
Quoted 1 line
+
iio_device_unregister(indio_dev);Hmm... Do you still need this even with devm IIO in ->probe()?
I *think* so, but that's mostly because all the other IIO light drivers that I've looked at are doing it. Can someone who knows the IIO subsystem well weigh in?
Yes, it is absolutely needed. This removes the userspace and core kernel interfaces 'before' we turn the power off. Without it there are some obvious race conditions. It's hard to query a sensor which is powered down after all.
You could wrap up the power off call in devm magic, but that will probably be more complex and error prone than doing it as we have here.
In cases where there is no clean up to do in order we can move to fully managed - this isn't one of those though.
Jonathan
Quoted 4 lines
Thanks!
Best,
Jonathan Cameron
maintainerQuoted 8 lines · On Wed, 21 Feb 2018 20:45:25 +0100 Pierre Bourdon <[email protected]> wrote:
Ambient light sensor that supports visible light and IR measurements and configurable gain/integration time.
Changed in v2:
* Split off DT documentation change into a separate commit.
* Use i2c'sprobe_new.Signed-off-by Pierre Bourdon <[email protected]>
Please send new versions as a new thread - all that happens with chaining them to the previous thread is things get very very difficult to follow sometimes. It's not obvious which version particular comments apply to or which patches are the latest for review.
A few questions inline but looking pretty good on the whole.
Jonathan
Quoted 235 lines
--- drivers/iio/light/Kconfig | 10 + drivers/iio/light/Makefile | 1 + drivers/iio/light/bh1730.c | 414 +++++++++++++++++++++++++++++++++++++ 3 files changed, 425 insertions(+) create mode 100644 drivers/iio/light/bh1730.cdrivers/iio/light/Kconfig +10
-0@@ -63,6 +63,16 @@ config APDS9960 To compile this driver as a module, choose M here: the module will be called apds9960 +config BH1730 + tristate "ROHM BH1730 ambient light sensor" + depends on I2C + help + Say Y here to build support for the ROHM BH1730FVC ambient + light sensor. + + To compile this driver as a module, choose M here: the module will + be called bh1730. + config BH1750 tristate "ROHM BH1750 ambient light sensor" depends on I2Cdrivers/iio/light/Makefile +1
-0@@ -9,6 +9,7 @@ obj-$(CONFIG_ADJD_S311) += adjd_s311.o obj-$(CONFIG_AL3320A) += al3320a.o obj-$(CONFIG_APDS9300) += apds9300.o obj-$(CONFIG_APDS9960) += apds9960.o +obj-$(CONFIG_BH1730) += bh1730.o obj-$(CONFIG_BH1750) += bh1750.o obj-$(CONFIG_BH1780) += bh1780.o obj-$(CONFIG_CM32181) += cm32181.odrivers/iio/light/bh1730.c new file +189
-0@@ -0,0 +1,414 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* ROHM BH1730 ambient light sensor driver +* +* Copyright (c) 2018 Google, Inc. +* Author: Pierre Bourdon <[email protected]> +* +* Based on a previous non-iio BH1730FVC driver: +* Copyright (C) 2012 Samsung Electronics. All rights reserved. +* Author: Won Huh <[email protected]> +* +* Data sheets: +* http://www.rohm.com/web/global/datasheet/BH1730FVC/bh1730fvc-e +*/ + +#include <linux/delay.h> +#include <linux/i2c.h> +#include <linux/iio/iio.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/time.h> + +#define BH1730_CMD_BIT BIT(7) + +#define BH1730_REG_CONTROL 0x00 +#define BH1730_REG_TIMING 0x01 +#define BH1730_REG_INTERRUPT 0x02 +#define BH1730_REG_THLLOW 0x03 +#define BH1730_REG_THLHIGH 0x04 +#define BH1730_REG_THHLOW 0x05 +#define BH1730_REG_THHHIGH 0x06 +#define BH1730_REG_GAIN 0x07 +#define BH1730_REG_ID 0x12 +#define BH1730_REG_DATA0LOW 0x14 +#define BH1730_REG_DATA0HIGH 0x15 +#define BH1730_REG_DATA1LOW 0x16 +#define BH1730_REG_DATA1HIGH 0x17 + +#define BH1730_CONTROL_POWER_ON BIT(0) +#define BH1730_CONTROL_MEASURE BIT(1) + +#define BH1730_INTERNAL_CLOCK_NS 2800ULL + +#define BH1730_DEFAULT_INTEG_MS 150 + +enum bh1730_gain { +BH1730_GAIN_1X =0 , +BH1730_GAIN_2X , +BH1730_GAIN_64X , +BH1730_GAIN_128X , +}; + +struct bh1730_data { +struct i2c_client *client; +enum bh1730_gain gain; +int itime; +}; + +static int bh1730_read_word (struct bh1730_data *bh1730,u8 reg) +{ +int ret =i2c_smbus_read_word_data (bh1730->client, +BH1730_CMD_BIT | reg); +if (ret <0 ) +dev_err (&bh1730->client->dev, +"i2c read failed error %d, register %01x\n" , + ret, reg); +return ret; +} + +static int bh1730_write (struct bh1730_data *bh1730,u8 reg,u8 val) +{ +int ret =i2c_smbus_write_byte_data (bh1730->client, +BH1730_CMD_BIT | reg, + val); +if (ret <0 ) +dev_err (&bh1730->client->dev, +"i2c write failed error %d, register %01x\n" , + ret, reg); +return ret; +} + +static int gain_setting_to_multiplier (enum bh1730_gain gain) +{ +switch (gain) { +case BH1730_GAIN_1X : +return 1 ; +case BH1730_GAIN_2X : +return 2 ; +case BH1730_GAIN_64X : +return 64 ; +case BH1730_GAIN_128X : +return 128 ; +default : +return -1 ; + } +} + +static int bh1730_gain_multiplier (struct bh1730_data *bh1730) +{ +int multiplier =gain_setting_to_multiplier (bh1730->gain); + +if (multiplier <0 ) { +dev_warn (&bh1730->client->dev, +"invalid gain multiplier settings: %d\n" , + bh1730->gain); + bh1730->gain =BH1730_GAIN_1X ; + multiplier =1 ; + } + +return multiplier; +} + +static u64 bh1730_itime_ns (struct bh1730_data *bh1730) +{ +return BH1730_INTERNAL_CLOCK_NS *964 * (256 - bh1730->itime); +} + +static int bh1730_set_gain (struct bh1730_data *bh1730,enum bh1730_gain gain) +{ +int ret =bh1730_write (bh1730,BH1730_REG_GAIN , gain); + +if (ret <0 ) +return ret; + + bh1730->gain = gain; +return 0 ; +} + +static int bh1730_set_integration_time_ms (struct bh1730_data *bh1730, +int time_ms) +{ +int ret; +u64 time_ns = time_ms * (u64 )NSEC_PER_MSEC ; +u64 itime_step_ns =BH1730_INTERNAL_CLOCK_NS *964 ; +int itime =256 - (int )DIV_ROUND_CLOSEST_ULL (time_ns, itime_step_ns); + +/* ITIME == 0 is reserved for manual integration mode. */ +if (itime <=0 || itime >255 ) { +dev_warn (&bh1730->client->dev, +"integration time out of range: %dms\n" , time_ms); +return -ERANGE ; + } + + ret =bh1730_write (bh1730,BH1730_REG_TIMING , itime); +if (ret <0 ) +return ret; + + bh1730->itime = itime; +return 0 ; +} + +static void bh1730_wait_for_next_measurement (struct bh1730_data *bh1730) +{ +ndelay (bh1730_itime_ns (bh1730) +BH1730_INTERNAL_CLOCK_NS *714 ); +} + +static int bh1730_adjust_gain (struct bh1730_data *bh1730) +{ +int visible, ir, highest, ret, i; + + visible =bh1730_read_word (bh1730,BH1730_REG_DATA0LOW ); +if (visible <0 ) +return visible; + + ir =bh1730_read_word (bh1730,BH1730_REG_DATA1LOW ); +if (ir <0 ) +return ir; + + highest =max (visible, ir); + +/* +* If the read value is being clamped, assume the worst and go to the +* lowest possible gain. The alternative is doing multiple +* recalibrations, which would be slower and have the same effect. +*/ +if (highest ==USHRT_MAX ) + highest *=128 ; +else + highest = (highest *128 ) /bh1730_gain_multiplier (bh1730); + +/* +* Find the lowest gain multiplier which puts the measured values +* above 1024. This threshold is chosen to match the gap between 2X +* multiplier and 64X (next available) while keeping some margin. +*/ +for (i =BH1730_GAIN_1X ; i <BH1730_GAIN_128X ; ++i) { +int adj = highest *gain_setting_to_multiplier (i) /128 ; + +if (adj >=1024 )
drivers/iio/light/bh1730.c line 199
Quoted 10 lines
drivers/iio/light/bh1730.c new file +10
-0+break ; + } + +if (i != bh1730->gain) { + ret =bh1730_set_gain (bh1730, i); +if (ret <0 ) +return ret; + +bh1730_wait_for_next_measurement (bh1730); + }
blank line here preferred and before all simple return statements like this.
Quoted 30 lines
drivers/iio/light/bh1730.c new file +30
-0+return 0 ; +} + +static s64 bh1730_get_millilux (struct bh1730_data *bh1730) +{ +int visible, ir, visible_coef, ir_coef; +u64 itime_us =bh1730_itime_ns (bh1730) /NSEC_PER_USEC ; +u64 millilux; + + visible =bh1730_read_word (bh1730,BH1730_REG_DATA0LOW ); +if (visible <0 ) +return visible; + + ir =bh1730_read_word (bh1730,BH1730_REG_DATA1LOW ); +if (ir <0 ) +return ir; + +if (ir *1000 / visible <500 ) { + visible_coef =5002 ; + ir_coef =7502 ; + }else if (ir *1000 / visible <754 ) { + visible_coef =2250 ; + ir_coef =2000 ; + }else if (ir *1000 / visible <1029 ) { + visible_coef =1999 ; + ir_coef =1667 ; + }else if (ir *1000 / visible <1373 ) { + visible_coef =885 ; + ir_coef =583 ; + }else if (ir *1000 / visible <1879 ) {
drivers/iio/light/bh1730.c line 239
Quoted 10 lines
drivers/iio/light/bh1730.c new file +10
-0+ visible_coef =309 ; + ir_coef =165 ; + }else { +return 0 ; + } + + millilux = (u64 )USEC_PER_MSEC * (visible_coef * visible - ir_coef * ir); + millilux /=bh1730_gain_multiplier (bh1730); + millilux *=103 ; + millilux /= itime_us;
Looks like the autobuilders got this but not all platforms support simple 64 bit divides so you'll need to use do_div and friends.
Quoted 59 lines
drivers/iio/light/bh1730.c new file +59
-0+return millilux; +} + +static int bh1730_power_on (struct bh1730_data *bh1730) +{ +return bh1730_write (bh1730,BH1730_REG_CONTROL , +BH1730_CONTROL_POWER_ON |BH1730_CONTROL_MEASURE ); +} + +static int bh1730_set_defaults (struct bh1730_data *bh1730) +{ +int ret; + + ret =bh1730_set_gain (bh1730,BH1730_GAIN_1X ); +if (ret <0 ) +return ret; + + ret =bh1730_set_integration_time_ms (bh1730,BH1730_DEFAULT_INTEG_MS ); +if (ret <0 ) +return ret; + +bh1730_wait_for_next_measurement (bh1730); +return 0 ; +} + +static int bh1730_power_off (struct bh1730_data *bh1730) +{ +return bh1730_write (bh1730,BH1730_REG_CONTROL ,0 ); +} + +static int bh1730_read_raw (struct iio_dev *indio_dev, +struct iio_chan_spec const *chan, +int *val,int *val2,long mask) +{ +struct bh1730_data *bh1730 =iio_priv (indio_dev); +int ret; +s64 millilux; + + ret =bh1730_adjust_gain (bh1730); +if (ret <0 ) +return ret; + +switch (mask) { +case IIO_CHAN_INFO_PROCESSED : + millilux =bh1730_get_millilux (bh1730); +if (millilux <0 ) +return millilux; + *val = millilux /1000 ; + *val2 = (millilux %1000 ) *1000 ; +return IIO_VAL_INT_PLUS_MICRO ; +case IIO_CHAN_INFO_RAW : +switch (chan->channel2) { +case IIO_MOD_LIGHT_CLEAR : + ret =bh1730_read_word (bh1730,BH1730_REG_DATA0LOW ); +if (ret <0 ) +return ret; + *val = ret; +return IIO_VAL_INT ; +case IIO_MOD_LIGHT_IR :
drivers/iio/light/bh1730.c line 308
Quoted 10 lines
drivers/iio/light/bh1730.c new file +10
-0+ ret =bh1730_read_word (bh1730,BH1730_REG_DATA1LOW ); +if (ret <0 ) +return ret; + *val = ret; +return IIO_VAL_INT ; +default : +return -EINVAL ; + } +case IIO_CHAN_INFO_SCALE : + *val =bh1730_gain_multiplier (bh1730);
As I read this, we get an instantaneous value of an auto adjusting gain. Given that won't necessarily correlate with any of the values, this doesn't work from the point of view of a user interface.
If you are going to do auto gain adjustment (which is fine) then it needs to be totally transparent to userspace to avoid issues like this.
Here I think that means we need to not expose scale but instead apply it a relevant to the raw values.
Quoted 9 lines
drivers/iio/light/bh1730.c new file +9
-0+return IIO_VAL_INT ; +default : +return -EINVAL ; + } +} + +static const struct iio_info bh1730_info = { + .read_raw = bh1730_read_raw, +};
drivers/iio/light/bh1730.c line 327
Quoted 10 lines
drivers/iio/light/bh1730.c new file +10
-0+ +static const struct iio_chan_spec bh1730_channels[] = { + { + .type =IIO_LIGHT , + .modified =1 , + .channel2 =IIO_MOD_LIGHT_BOTH , + .info_mask_separate =BIT (IIO_CHAN_INFO_PROCESSED ), + }, + { + .type =IIO_LIGHT ,
Hmm. When we have a split sensor like this it is usually impossible to relate the particular light sensor to the units of 'light' - i.e. lux in IIO. Hence we use the intensity type for the separate fields.
I'm guessing you copied this from another driver though which probably means something go through when we weren't paying attention...
drivers/iio/light/bh1730.c line 331
Quoted 4 lines
drivers/iio/light/bh1730.c new file +4
-0+ .modified = 1, + .channel2 = IIO_MOD_LIGHT_CLEAR, + .info_mask_separate =BIT (IIO_CHAN_INFO_RAW ) | + BIT(IIO_CHAN_INFO_SCALE),
What are units of this and the IR sensor below?
Quoted 83 lines
drivers/iio/light/bh1730.c new file +83
-0+ }, + { + .type = IIO_LIGHT, + .modified = 1, + .channel2 = IIO_MOD_LIGHT_IR, + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | + BIT(IIO_CHAN_INFO_SCALE), + }, +}; + +static int bh1730_probe (struct i2c_client *client) +{ +struct bh1730_data *bh1730; +struct i2c_adapter *adapter =to_i2c_adapter (client->dev.parent); +struct iio_dev *indio_dev; +int ret; + +if (!i2c_check_functionality (adapter,I2C_FUNC_SMBUS_BYTE )) +return -EIO ; + + indio_dev =devm_iio_device_alloc (&client->dev,sizeof (*bh1730)); +if (!indio_dev) +return -ENOMEM ; + + bh1730 =iio_priv (indio_dev); + bh1730->client = client; +i2c_set_clientdata (client, indio_dev); + + ret =bh1730_power_on (bh1730); +if (ret <0 ) +return ret; + + ret =bh1730_set_defaults (bh1730); +if (ret <0 ) +return ret; + + indio_dev->dev.parent = &client->dev; + indio_dev->info = &bh1730_info; + indio_dev->name ="bh1730" ; + indio_dev->channels = bh1730_channels; + indio_dev->num_channels =ARRAY_SIZE (bh1730_channels); + indio_dev->modes =INDIO_DIRECT_MODE ; + + ret =iio_device_register (indio_dev); +if (ret) + goto out_power_off; +return 0 ; + +out_power_off: +bh1730_power_off (bh1730); +return ret; +} + +static int bh1730_remove (struct i2c_client *client) +{ +struct iio_dev *indio_dev =i2c_get_clientdata (client); +struct bh1730_data *bh1730 =iio_priv (indio_dev); + +iio_device_unregister (indio_dev); +return bh1730_power_off (bh1730); +} + +#ifdef CONFIG_OF +static const struct of_device_id of_bh1730_match[] = { + { .compatible ="rohm,bh1730fvc" }, + {}, +}; +MODULE_DEVICE_TABLE (of, of_bh1730_match); +#endif + +static struct i2c_driver bh1730_driver = { + .probe_new = bh1730_probe, + .remove = bh1730_remove, + .driver = { + .name ="bh1730" , + .of_match_table =of_match_ptr (of_bh1730_match), + }, +}; +module_i2c_driver (bh1730_driver); + +MODULE_AUTHOR ("Pierre Bourdon <[email protected]>" ); +MODULE_DESCRIPTION ("ROHM BH1730FVC driver" ); +MODULE_LICENSE ("GPL v2" );
kbuild test robot
build botThank you for the patch! Yet something to improve:
Hi Pierre,
Thank you for the patch! Yet something to improve:
[auto build test ERROR on iio/togreg]
[also build test ERROR on v4.16-rc2 next-20180222]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Pierre-Bourdon/iio-light-add-driver-for-bh1730fvc-chips/20180222-064336 base: https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio.git togreg config: i386-allyesconfig (attached as .config) compiler: gcc-7 (Debian 7.3.0-1) 7.3.0 reproduce: # save the attached .config to linux build tree make ARCH=i386
All errors (new ones prefixed by >>):
drivers/iio/light/bh1730.o: In function `bh1730_read_raw':
>> bh1730.c:(.text+0x31d): undefined reference to `__udivdi3' bh1730.c:(.text+0x37d): undefined reference to `__udivdi3' bh1730.c:(.text+0x38a): undefined reference to `__udivdi3' >> bh1730.c:(.text+0x3a4): undefined reference to `__divdi3' >> bh1730.c:(.text+0x3b8): undefined reference to `__moddi3'
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation