Skip to contentSkip to conversation

drm/i915/skl+: Add and enable DP AUX CH mutex

PATCH In review José Roberto de Souza 3 participants 8 messages Feb 24, 2018 – Feb 27, 2018

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/6 drm/i915/skl+: Add and enable DP AUX CH mutex

***
Please do not send review to this patch here, it was sent separated
https://lists.freedesktop.org/archives/intel-gfx/2018-February/156921.html
it is only included here to avoid concurrency access when reading sink PSR status and errors registers
***

When PSR/PSR2/GTC is enabled hardware can do AUX transactions by it self, so lets use the mutex register that is available in gen9+ to avoid concurrent access by hardware and driver.
Older gen handling will be done separated.

Reference: https://01.org/sites/default/files/documentation/intel-gfx-prm-osrc-skl-vol12-display.pdf
Page 198 - AUX programming sequence

---
 drivers/gpu/drm/i915/i915_reg.h  |  9 ++++++
 drivers/gpu/drm/i915/intel_dp.c  | 67 ++++++++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_drv.h |  1 +
 3 files changed, 77 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +9 -0
index eea5b2c537d4..f36e839b4b4f 100644
@@ -5385,6 +5385,15 @@ enum {
 #define   DP_AUX_CH_CTL_FW_SYNC_PULSE_SKL(c) (((c) - 1) << 5)
 #define   DP_AUX_CH_CTL_SYNC_PULSE_SKL(c)   ((c) - 1)
 
+#define _DPA_AUX_CH_MUTEX	(dev_priv->info.display_mmio_offset + 0x6402C)
+#define _DPB_AUX_CH_MUTEX	(dev_priv->info.display_mmio_offset + 0x6412C)
+#define _DPC_AUX_CH_MUTEX	(dev_priv->info.display_mmio_offset + 0x6422C)
+#define _DPD_AUX_CH_MUTEX	(dev_priv->info.display_mmio_offset + 0x6432C)
+#define _DPF_AUX_CH_MUTEX	(dev_priv->info.display_mmio_offset + 0x6452C)
+#define DP_AUX_CH_MUTEX(port)	_MMIO_PORT(port, _DPA_AUX_CH_MUTEX, _DPB_AUX_CH_MUTEX)
+#define   DP_AUX_CH_MUTEX_ENABLE		(1 << 31)
+#define   DP_AUX_CH_MUTEX_STATUS		(1 << 30)
+
 /*
  * Computing GMCH M and N values for the Display Port link
  *
drivers/gpu/drm/i915/intel_dp.c +67 -0

97 lines not on this page · raw message

drivers/gpu/drm/i915/intel_drv.h +1 -0
index 8f38e584d375..267cc6c5a89f 100644
@@ -1128,6 +1128,7 @@ struct intel_dp {
 
 	i915_reg_t (*aux_ch_ctl_reg)(struct intel_dp *dp);
 	i915_reg_t (*aux_ch_data_reg)(struct intel_dp *dp, int index);
+	i915_reg_t (*aux_ch_mutex_reg)(struct intel_dp *dp);
 
 	/* This is called before a link training is starterd */
 	void (*prepare_link_retrain)(struct intel_dp *intel_dp);
Signature · 6 lines
2.16.2

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#1 lore raw

PATCH 2/6 drm/i915/psr: Share the common code between PSR exit and disable

---
 drivers/gpu/drm/i915/i915_drv.h  |   1 +
 drivers/gpu/drm/i915/intel_psr.c | 199 +++++++++++++++++++--------------------
 2 files changed, 96 insertions(+), 104 deletions(-)
drivers/gpu/drm/i915/i915_drv.h +1 -0
index 82a106b1bdbc..44b551f1576d 100644
@@ -780,6 +780,7 @@ struct i915_psr {
 	void (*enable_sink)(struct intel_dp *);
 	void (*activate)(struct intel_dp *);
 	void (*setup_vsc)(struct intel_dp *, const struct intel_crtc_state *);
+	void (*exit)(struct intel_dp *intel_dp, bool wait_exit);
 };
 
 enum intel_pch {
drivers/gpu/drm/i915/intel_psr.c +95 -104

249 lines not on this page · raw message

Signature · 6 lines
2.16.2

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#2 lore raw

PATCH 3/6 drm/i915: Exit PSR before do a aux transaction in gen < 9

In reply to José Roberto de Souza

As gen < 9 hardware don't have the aux ch mutex, we need to exit PSR and wait until it is back to inactive state before do any aux ch transaction.

---
 drivers/gpu/drm/i915/intel_dp.c  |  8 +++++++-
 drivers/gpu/drm/i915/intel_drv.h |  9 +++++++++
 drivers/gpu/drm/i915/intel_psr.c | 42 ++++++++++++++++++++++++++++++++++------
 3 files changed, 52 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/intel_dp.c +7 -1
index 7be2fec51651..dacdd98bbb2e 100644
@@ -1088,8 +1088,14 @@ static bool intel_dp_aux_ch_trylock(struct intel_dp *intel_dp)
 			to_i915(intel_dig_port->base.base.dev);
 	i915_reg_t ch_mutex;
 
-	if (!intel_dp->aux_ch_mutex_reg)
+	if (!intel_dp->aux_ch_mutex_reg) {
+		/* As gen < 9 hardware don't have the aux ch mutex, we need to
+		 * exit PSR and wait until it is back to inactive state before
+		 * do any aux ch transaction
+		 */
+		intel_psr_exit(intel_dp, true);
 		return true;
+	}
 
 	ch_mutex = intel_dp->aux_ch_mutex_reg(intel_dp);
 	I915_WRITE(ch_mutex, DP_AUX_CH_MUTEX_ENABLE);
drivers/gpu/drm/i915/intel_drv.h +9 -0
index 267cc6c5a89f..7adcd5955d1b 100644
@@ -1881,6 +1881,15 @@ void intel_psr_single_frame_update(struct drm_i915_private *dev_priv,
 				   unsigned frontbuffer_bits);
 void intel_psr_compute_config(struct intel_dp *intel_dp,
 			      struct intel_crtc_state *crtc_state);
+/**
+ * Exit PSR in the given DisplayPort.
+ * @intel_dp: DisplayPort which PSR should be exit if running
+ * @wait_exit: if true it will wait until PSR have changed to inactive state,
+ * otherwise there is not wait.
+ *
+ * It will also schedule a work to try to active PSR again.
+ */
+void intel_psr_exit(struct intel_dp *intel_dp, bool wait_exit);
 
 /* intel_runtime_pm.c */
 int intel_power_domains_init(struct drm_i915_private *);
drivers/gpu/drm/i915/intel_psr.c +36 -6

69 lines not on this page · raw message

Signature · 6 lines
2.16.2

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#3 lore raw

Re: [PATCH 3/6] drm/i915: Exit PSR before do a aux transaction in gen < 9

Quoted 4 lines · José Roberto de Souza

As gen < 9 hardware don't have the aux ch mutex, we need to exit PSR and wait until it is back to inactive state before do any aux ch transaction.

I wonder if we need this for CHV/VLV since the HW does not send PSR aux transactions on it's own.

Quoted 62 lines
---
 drivers/gpu/drm/i915/intel_dp.c  |  8 +++++++-
 drivers/gpu/drm/i915/intel_drv.h |  9 +++++++++
 drivers/gpu/drm/i915/intel_psr.c | 42 ++++++++++++++++++++++++++++++++++------
 3 files changed, 52 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/intel_dp.c +7 -1
index 7be2fec51651..dacdd98bbb2e 100644
@@ -1088,8 +1088,14 @@ static bool intel_dp_aux_ch_trylock(struct intel_dp *intel_dp)
 			to_i915(intel_dig_port->base.base.dev);
 	i915_reg_t ch_mutex;
 
-	if (!intel_dp->aux_ch_mutex_reg)
+	if (!intel_dp->aux_ch_mutex_reg) {
+		/* As gen < 9 hardware don't have the aux ch mutex, we need to
+		 * exit PSR and wait until it is back to inactive state before
+		 * do any aux ch transaction
+		 */
+		intel_psr_exit(intel_dp, true);
 		return true;
+	}
 
 	ch_mutex = intel_dp->aux_ch_mutex_reg(intel_dp);
 	I915_WRITE(ch_mutex, DP_AUX_CH_MUTEX_ENABLE);
drivers/gpu/drm/i915/intel_drv.h +9 -0
index 267cc6c5a89f..7adcd5955d1b 100644
@@ -1881,6 +1881,15 @@ void intel_psr_single_frame_update(struct drm_i915_private *dev_priv,
 				   unsigned frontbuffer_bits);
 void intel_psr_compute_config(struct intel_dp *intel_dp,
 			      struct intel_crtc_state *crtc_state);
+/**
+ * Exit PSR in the given DisplayPort.
+ * @intel_dp: DisplayPort which PSR should be exit if running
+ * @wait_exit: if true it will wait until PSR have changed to inactive state,
+ * otherwise there is not wait.
+ *
+ * It will also schedule a work to try to active PSR again.
+ */
+void intel_psr_exit(struct intel_dp *intel_dp, bool wait_exit);
 
 /* intel_runtime_pm.c */
 int intel_power_domains_init(struct drm_i915_private *);
drivers/gpu/drm/i915/intel_psr.c +2 -0
index e8c32c3afb0e..0b889c85e8da 100644
@@ -56,6 +56,8 @@
 #include "intel_drv.h"
 #include "i915_drv.h"
 
+#define PSR_ACTIVE_DELAY_MSEC 100
+
 static bool vlv_is_psr_active_on_pipe(struct drm_device *dev, int pipe)
 {
 	struct drm_i915_private *dev_priv = to_i915(dev);
@@ -486,6 +488,16 @@ static void hsw_psr_enable_source(struct intel_dp *intel_dp,
 	}

drivers/gpu/drm/i915/intel_psr.c static void hsw_psr_enable_source(struct intel_dp *intel_dp, · line 498

Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +8 -0
 }
 
+static void intel_psr_active_schedule(struct i915_psr *psr,
+				      unsigned int msec_delay)
+{
+	if (psr->active || psr->busy_frontbuffer_bits)
+		return;
+
+	if (!work_busy(&psr->work.work))
+		schedule_delayed_work(&psr->work, msecs_to_jiffies(msec_delay));

This change will conflict with
https://patchwork.freedesktop.org/series/38199/

Quoted 40 lines
drivers/gpu/drm/i915/intel_psr.c +13 -6
+}
+
 /**
  * intel_psr_enable - Enable PSR
  * @intel_dp: Intel DP
@@ -534,8 +546,9 @@ void intel_psr_enable(struct intel_dp *intel_dp,
 		 *     - On HSW/BDW we get a recoverable frozen screen until
 		 *       next exit-activate sequence.
 		 */
-		schedule_delayed_work(&dev_priv->psr.work,
-				      msecs_to_jiffies(intel_dp->panel_power_cycle_delay * 5));
+		intel_psr_active_schedule(&dev_priv->psr,
+					  intel_dp->panel_power_cycle_delay
+					  * 5);
 	}
 
 unlock:
@@ -886,10 +899,7 @@ void intel_psr_flush(struct drm_i915_private *dev_priv,
 	if (frontbuffer_bits)
 		dev_priv->psr.exit(dev_priv->psr.enabled, false);
 
-	if (!dev_priv->psr.active && !dev_priv->psr.busy_frontbuffer_bits)
-		if (!work_busy(&dev_priv->psr.work.work))
-			schedule_delayed_work(&dev_priv->psr.work,
-					      msecs_to_jiffies(100));
+	intel_psr_active_schedule(&dev_priv->psr, PSR_ACTIVE_DELAY_MSEC);
 	mutex_unlock(&dev_priv->psr.lock);
 }
 
@@ -955,3 +965,23 @@ void intel_psr_init(struct drm_i915_private *dev_priv)
 		dev_priv->psr.exit = hsw_psr_exit;
 	}
 }
+
+void intel_psr_exit(struct intel_dp *intel_dp, bool wait_exit)
+{
+	struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp);
+	struct drm_device *dev = intel_dig_port->base.base.dev;
+	struct drm_i915_private *dev_priv = to_i915(dev);
+

drivers/gpu/drm/i915/intel_psr.c void intel_psr_init(struct drm_i915_private *dev_priv) · line 984

Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +10 -0
+	if (!HAS_PSR(dev_priv))
+		return;
+
+	mutex_lock(&dev_priv->psr.lock);
+
+	if (dev_priv->psr.enabled != intel_dp)
+		goto out;
+
+	dev_priv->psr.exit(intel_dp, wait_exit);
+	intel_psr_active_schedule(&dev_priv->psr, PSR_ACTIVE_DELAY_MSEC);

psr_exit scheduling an activate looks wrong and it is also exactly what psr_flush does.

I suppose we could call psr_invalidate at the beginning of the aux transaction and psr_flush at the end. But the question is what arguments do we pass to those functions.

Or we could just call psr_exit at the start (without scheduling activate) and psr_activate at the end.

drivers/gpu/drm/i915/intel_psr.c void intel_psr_init(struct drm_i915_private *dev_priv) · line 987

Quoted 3 lines
drivers/gpu/drm/i915/intel_psr.c +3 -0
+out:
+	mutex_unlock(&dev_priv->psr.lock);
+}

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#4 lore raw

PATCH 4/6 drm/i915/psr: Begin to handle PSR/PSR2 errors set by sink

In reply to José Roberto de Souza

Sink device will do a short pulse in HPD line when there is some PSR/PSR2 error that needs to be handled by source, this is handling the first and most simples error: DP_PSR_SINK_INTERNAL_ERROR.

---
 drivers/gpu/drm/i915/intel_dp.c  |  2 ++
 drivers/gpu/drm/i915/intel_drv.h |  1 +
 drivers/gpu/drm/i915/intel_psr.c | 31 +++++++++++++++++++++++++++++++
 3 files changed, 34 insertions(+)
drivers/gpu/drm/i915/intel_dp.c +2 -0
index dacdd98bbb2e..955bf85e9b20 100644
@@ -4549,6 +4549,8 @@ intel_dp_short_pulse(struct intel_dp *intel_dp)
 
 	intel_dp_check_link_status(intel_dp);
 
+	intel_psr_hpd_short_pulse_handle(intel_dp);
+
 	if (intel_dp->compliance.test_type == DP_TEST_LINK_TRAINING) {
 		DRM_DEBUG_KMS("Link Training Compliance Test requested\n");
 		/* Send a Hotplug Uevent to userspace to start modeset */
drivers/gpu/drm/i915/intel_drv.h +1 -0
index 7adcd5955d1b..a0bd00787a98 100644
@@ -1890,6 +1890,7 @@ void intel_psr_compute_config(struct intel_dp *intel_dp,
  * It will also schedule a work to try to active PSR again.
  */
 void intel_psr_exit(struct intel_dp *intel_dp, bool wait_exit);
+void intel_psr_hpd_short_pulse_handle(struct intel_dp *intel_dp);
 
 /* intel_runtime_pm.c */
 int intel_power_domains_init(struct drm_i915_private *);
drivers/gpu/drm/i915/intel_psr.c +31 -0
index 0b889c85e8da..ab3713c2582b 100644
@@ -985,3 +985,34 @@ void intel_psr_exit(struct intel_dp *intel_dp, bool wait_exit)
 out:
 	mutex_unlock(&dev_priv->psr.lock);
 }
+
+void intel_psr_hpd_short_pulse_handle(struct intel_dp *intel_dp)
+{
+	struct intel_digital_port *intel_dig_port = dp_to_dig_port(intel_dp);
+	struct drm_device *dev = intel_dig_port->base.base.dev;
+	struct drm_i915_private *dev_priv = to_i915(dev);
+	struct i915_psr *psr = &dev_priv->psr;
+	uint8_t val;
+
+	if (!HAS_PSR(dev_priv))
+		return;
+
+	mutex_lock(&psr->lock);
+
+	if (psr->enabled != intel_dp)
+		goto out;
+
+	if (drm_dp_dpcd_readb(&intel_dp->aux, DP_PSR_STATUS, &val) != 1) {
+		DRM_DEBUG_KMS("PSR_STATUS read failed\n");
+		goto dpcd_read_error;
+	}
+
+	if ((val & DP_PSR_SINK_STATE_MASK) == DP_PSR_SINK_INTERNAL_ERROR)
+		psr->exit(intel_dp, false);
+
+	/* TODO: handle other PSR/PSR2 errors */
+dpcd_read_error:
+	intel_psr_active_schedule(psr, PSR_ACTIVE_DELAY_MSEC);
+out:
+	mutex_unlock(&psr->lock);
+}
Signature · 6 lines
2.16.2

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#5 lore raw

PATCH 5/6 drm/i915/psr: Handle PSR RFB storage error

In reply to José Roberto de Souza

Sink will interrupt source when it have any problem saving or reading the remote frame buffer.

---
 drivers/gpu/drm/i915/intel_psr.c | 10 ++++++++++
 1 file changed, 10 insertions(+)
drivers/gpu/drm/i915/intel_psr.c +10 -0
index ab3713c2582b..4e73edf1ea5b 100644
@@ -1010,6 +1010,16 @@ void intel_psr_hpd_short_pulse_handle(struct intel_dp *intel_dp)
 	if ((val & DP_PSR_SINK_STATE_MASK) == DP_PSR_SINK_INTERNAL_ERROR)
 		psr->exit(intel_dp, false);
 
+	if (drm_dp_dpcd_readb(&intel_dp->aux, DP_PSR_ERROR_STATUS, &val) != 1) {
+		DRM_DEBUG_KMS("PSR_ERROR_STATUS read failed\n");
+		goto dpcd_read_error;
+	}
+
+	if (val & DP_PSR_RFB_STORAGE_ERROR)
+		dev_priv->psr.exit(intel_dp, false);
+	/* clear status register */
+	drm_dp_dpcd_writeb(&intel_dp->aux, DP_PSR_ERROR_STATUS, val);
+
 	/* TODO: handle other PSR/PSR2 errors */
 dpcd_read_error:
 	intel_psr_active_schedule(psr, PSR_ACTIVE_DELAY_MSEC);
Signature · 6 lines
2.16.2

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#6 lore raw

PATCH 6/6 drm/i915/psr/hsw+: Enable CRC check in the static frame on the sink side

In reply to José Roberto de Souza

Sink can be configured to calculate the CRC over the static frame and compare with the CRC calculated and transmited in the VSC SDP by source, if there is a mismatch sink will do a short pulse in HPD and set DP_PSR_LINK_CRC_ERROR on DP_PSR_ERROR_STATUS.

---
 drivers/gpu/drm/i915/i915_reg.h  |  1 +
 drivers/gpu/drm/i915/intel_psr.c | 15 +++++++--------
 2 files changed, 8 insertions(+), 8 deletions(-)
drivers/gpu/drm/i915/i915_reg.h +1 -0
index f36e839b4b4f..ca68eef8d90a 100644
@@ -4122,6 +4122,7 @@ enum {
 #define   EDP_PSR_SKIP_AUX_EXIT			(1<<12)
 #define   EDP_PSR_TP1_TP2_SEL			(0<<11)
 #define   EDP_PSR_TP1_TP3_SEL			(1<<11)
+#define   EDP_PSR_CRC_ENABLE			(1<<10)
 #define   EDP_PSR_TP2_TP3_TIME_500us		(0<<8)
 #define   EDP_PSR_TP2_TP3_TIME_100us		(1<<8)
 #define   EDP_PSR_TP2_TP3_TIME_2500us		(2<<8)
drivers/gpu/drm/i915/intel_psr.c +7 -8
index 4e73edf1ea5b..f6af8e8039c9 100644
@@ -160,6 +160,7 @@ static void hsw_psr_enable_sink(struct intel_dp *intel_dp)
 	enum port port = dig_port->base.port;
 	u32 aux_ctl;
 	int i;
+	uint8_t val;
 
 	BUILD_BUG_ON(sizeof(aux_msg) > 20);
 
@@ -175,12 +176,10 @@ static void hsw_psr_enable_sink(struct intel_dp *intel_dp)
 		drm_dp_dpcd_writeb(&intel_dp->aux,
 				DP_RECEIVER_ALPM_CONFIG,
 				DP_ALPM_ENABLE);
+	val = DP_PSR_ENABLE | DP_PSR_CRC_VERIFICATION;
 	if (dev_priv->psr.link_standby)
-		drm_dp_dpcd_writeb(&intel_dp->aux, DP_PSR_EN_CFG,
-				   DP_PSR_ENABLE | DP_PSR_MAIN_LINK_ACTIVE);
-	else
-		drm_dp_dpcd_writeb(&intel_dp->aux, DP_PSR_EN_CFG,
-				   DP_PSR_ENABLE);
+		val |= DP_PSR_MAIN_LINK_ACTIVE;
+	drm_dp_dpcd_writeb(&intel_dp->aux, DP_PSR_EN_CFG, val);
 
 	aux_ctl_reg = psr_aux_ctl_reg(dev_priv, port);
 
@@ -241,7 +240,7 @@ static void hsw_activate_psr1(struct intel_dp *intel_dp)
 	 * with the 5 or 6 idle patterns.
 	 */
 	uint32_t idle_frames = max(6, dev_priv->vbt.psr.idle_frames);
-	uint32_t val = EDP_PSR_ENABLE;
+	uint32_t val = EDP_PSR_ENABLE | EDP_PSR_CRC_ENABLE;
 
 	val |= max_sleep_time << EDP_PSR_MAX_SLEEP_TIME_SHIFT;
 	val |= idle_frames << EDP_PSR_IDLE_FRAME_SHIFT;
@@ -1015,12 +1014,12 @@ void intel_psr_hpd_short_pulse_handle(struct intel_dp *intel_dp)
 		goto dpcd_read_error;
 	}
 
-	if (val & DP_PSR_RFB_STORAGE_ERROR)
+	if (val & (DP_PSR_RFB_STORAGE_ERROR | DP_PSR_LINK_CRC_ERROR))
 		dev_priv->psr.exit(intel_dp, false);
 	/* clear status register */
 	drm_dp_dpcd_writeb(&intel_dp->aux, DP_PSR_ERROR_STATUS, val);
 
-	/* TODO: handle other PSR/PSR2 errors */
+	/* TODO: handle PSR2 errors */
 dpcd_read_error:
 	intel_psr_active_schedule(psr, PSR_ACTIVE_DELAY_MSEC);
 out:
Signature · 6 lines
2.16.2

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#7 lore raw

✗ Fi.CI.BAT: failure for series starting with [1/6] drm/i915/skl+: Add and enable DP AUX CH mutex

In reply to José Roberto de Souza
== Series Details ==

== Series Details ==

Series: series starting with [1/6] drm/i915/skl+: Add and enable DP AUX CH mutex
URL : https://patchwork.freedesktop.org/series/38902/
State : failure

== Summary ==

Series 38902v1 series starting with [1/6] drm/i915/skl+: Add and enable DP AUX CH mutex
https://patchwork.freedesktop.org/api/1.0/series/38902/revisions/1/mbox/

Test gem_exec_suspend:

        Subgroup basic-s3:
                pass       -> FAIL       (fi-skl-guc)
Test kms_busy:
        Subgroup basic-flip-a:
                pass       -> DMESG-WARN (fi-skl-6700k2)
Test kms_force_connector_basic:
        Subgroup force-connector-state:
                skip       -> PASS       (fi-snb-2520m)
        Subgroup force-edid:
                skip       -> PASS       (fi-snb-2520m)
        Subgroup force-load-detect:
                skip       -> PASS       (fi-snb-2520m)
        Subgroup prune-stale-modes:
                skip       -> PASS       (fi-snb-2520m)
Test kms_pipe_crc_basic:
        Subgroup suspend-read-crc-pipe-c:
                incomplete -> PASS       (fi-bxt-dsi) fdo#103927

fdo#103927 https://bugs.freedesktop.org/show_bug.cgi?id=103927

fi-bdw-5557u     total:288  pass:267  dwarn:0   dfail:0   fail:0   skip:21  time:406s
fi-bdw-gvtdvm    total:288  pass:264  dwarn:0   dfail:0   fail:0   skip:24  time:423s
fi-blb-e6850     total:288  pass:223  dwarn:1   dfail:0   fail:0   skip:64  time:373s
fi-bsw-n3050     total:288  pass:242  dwarn:0   dfail:0   fail:0   skip:46  time:440s
fi-bwr-2160      total:288  pass:183  dwarn:0   dfail:0   fail:0   skip:105 time:283s
fi-bxt-dsi       total:288  pass:258  dwarn:0   dfail:0   fail:0   skip:30  time:476s
fi-bxt-j4205     total:288  pass:259  dwarn:0   dfail:0   fail:0   skip:29  time:485s
fi-byt-j1900     total:288  pass:253  dwarn:0   dfail:0   fail:0   skip:35  time:424s
fi-byt-n2820     total:288  pass:249  dwarn:0   dfail:0   fail:0   skip:39  time:417s
fi-cfl-8700k     total:288  pass:260  dwarn:0   dfail:0   fail:0   skip:28  time:393s
fi-cfl-s2        total:288  pass:262  dwarn:0   dfail:0   fail:0   skip:26  time:565s
fi-cnl-y3        total:288  pass:262  dwarn:0   dfail:0   fail:0   skip:26  time:576s
fi-elk-e7500     total:288  pass:229  dwarn:0   dfail:0   fail:0   skip:59  time:419s
fi-gdg-551       total:288  pass:179  dwarn:0   dfail:0   fail:1   skip:108 time:283s
fi-glk-1         total:288  pass:260  dwarn:0   dfail:0   fail:0   skip:28  time:508s
fi-hsw-4770      total:288  pass:261  dwarn:0   dfail:0   fail:0   skip:27  time:384s
fi-ilk-650       total:288  pass:228  dwarn:0   dfail:0   fail:0   skip:60  time:407s
fi-ivb-3520m     total:288  pass:259  dwarn:0   dfail:0   fail:0   skip:29  time:452s
fi-ivb-3770      total:288  pass:255  dwarn:0   dfail:0   fail:0   skip:33  time:412s
fi-kbl-7500u     total:288  pass:262  dwarn:1   dfail:0   fail:1   skip:24  time:439s
fi-kbl-7560u     total:288  pass:269  dwarn:0   dfail:0   fail:0   skip:19  time:491s
fi-kbl-7567u     total:288  pass:268  dwarn:0   dfail:0   fail:0   skip:20  time:444s
fi-kbl-r         total:288  pass:261  dwarn:0   dfail:0   fail:0   skip:27  time:494s
fi-pnv-d510      total:288  pass:222  dwarn:1   dfail:0   fail:0   skip:65  time:591s
fi-skl-6260u     total:288  pass:268  dwarn:0   dfail:0   fail:0   skip:20  time:428s
fi-skl-6600u     total:288  pass:261  dwarn:0   dfail:0   fail:0   skip:27  time:502s
fi-skl-6700hq    total:288  pass:262  dwarn:0   dfail:0   fail:0   skip:26  time:517s
fi-skl-6700k2    total:288  pass:263  dwarn:1   dfail:0   fail:0   skip:24  time:478s
fi-skl-6770hq    total:288  pass:268  dwarn:0   dfail:0   fail:0   skip:20  time:458s
fi-skl-guc       total:288  pass:259  dwarn:0   dfail:0   fail:1   skip:28  time:404s
fi-skl-gvtdvm    total:288  pass:265  dwarn:0   dfail:0   fail:0   skip:23  time:430s
fi-snb-2520m     total:288  pass:248  dwarn:0   dfail:0   fail:0   skip:40  time:523s
fi-snb-2600      total:288  pass:248  dwarn:0   dfail:0   fail:0   skip:40  time:392s

316ba650abe6c1e8ac2f812ff21eee5771546ba1 drm-tip: 2018y-02m-23d-16h-41m-52s UTC integration manifest ef1e257d5daa drm/i915/psr/hsw+: Enable CRC check in the static frame on the sink side 5c88fa2403cd drm/i915/psr: Handle PSR RFB storage error
44e795fcba6e drm/i915/psr: Begin to handle PSR/PSR2 errors set by sink
7ff88cb1e65b drm/i915: Exit PSR before do a aux transaction in gen < 9
c796fc99157a drm/i915/psr: Share the common code between PSR exit and disable daa39e989d5f drm/i915/skl+: Add and enable DP AUX CH mutex

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_8152/issues.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx