ARM: dts: imx6qdl-hummingboard: fix USBOTG-ID pin
Subsystems (2)
PATCH 1/2 ARM: dts: imx6qdl-hummingboard: fix USBOTG-ID pin
From: Jon Nettleton <[email protected]>
Fix the USBOTG-ID pin to the correct definition. The top USB port stays in device-mode without this change.
--- arch/arm/boot/dts/imx6qdl-hummingboard.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/imx6qdl-hummingboard.dtsi +1 -1
@@ -242,7 +242,7 @@ * Similar to pinctrl_usbotg_2, but we want it * pulled down for a fixed host connection. */ - fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>; + fsl,pins = <MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x13059>; }; pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
Signature · 1 line
2.16.1
PATCH 2/2 ARM: dts: hummingboard: Remove mention of nonexistent node
There is no pinctrl_usbotg_2 node in current Hummingboard dts files. Drop reference to that.
--- arch/arm/boot/dts/imx6qdl-hummingboard.dtsi | 3 +-- arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi | 3 +-- 2 files changed, 2 insertions(+), 4 deletions(-)
arch/arm/boot/dts/imx6qdl-hummingboard.dtsi +1 -2
@@ -239,8 +239,7 @@ pinctrl_hummingboard_usbotg_id: hummingboard-usbotg-id { /* - * Similar to pinctrl_usbotg_2, but we want it - * pulled down for a fixed host connection. + * We want it pulled down for a fixed host connection. */ fsl,pins = <MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x13059>; };
arch/arm/boot/dts/imx6qdl-hummingboard2.dtsi +1 -2
@@ -409,8 +409,7 @@ pinctrl_hummingboard2_usbotg_id: hummingboard2-usbotg-id { /* - * Similar to pinctrl_usbotg_2, but we want it - * pulled down for a fixed host connection. + * We want it pulled down for a fixed host connection. */ fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>; };
Signature · 1 line
2.16.1
Fabio Estevam
reviewerPATCH 2/2 ARM: dts: hummingboard: Remove mention of nonexistent node
Quoted 4 lines · Baruch Siach
There is no
pinctrl_usbotg_2node in current Hummingboard dts files. Drop reference to that.Signed-off-by Baruch Siach <[email protected]>
Shawn Guo
AppliedPATCH 1/2 ARM: dts: imx6qdl-hummingboard: fix USBOTG-ID pin
In reply to Baruch SiachQuoted 7 lines · Baruch Siach
From: Jon Nettleton <[email protected]>
Fix the USBOTG-ID pin to the correct definition. The top USB port stays in device-mode without this change.
Signed-off-by Jon Nettleton <[email protected]>Signed-off-by Baruch Siach <[email protected]>
Applied both, thanks.