RPi: Drain RX queue on setbrg
Subsystems (2)
cover RPi: Drain RX queue on setbrg
We had a few reports coming in from people that had their autoboot chain aborted after pinmuxing support was added for the RPi.
The culprit is easy: The UARTs may have been enabled before, but muxed to an incorrect pin. That pin may have pulled the RX line down which again lead to lots of zero bytes gathered in the RX buffer.
The easy fix for that is to drain the RX queue every time we set the baud rate.
This patch set is the minimally intrusive fix for the RPi. We may want to do that generically for all serial devices later.
Alexander Graf (2):
serial_bcm283x_mu: Flush RX queue after setting baud rate
bcm283x_pl011: Flush RX queue after setting baud rate
drivers/serial/serial_bcm283x_mu.c | 8 +++++++- drivers/serial/serial_bcm283x_pl011.c | 25 ++++++++++++++++++++++++- drivers/serial/serial_pl01x.c | 10 +++++----- drivers/serial/serial_pl01x_internal.h | 7 ++++++- 4 files changed, 42 insertions(+), 8 deletions(-)
Signature · 1 line
2.12.3
PATCH 1/2 serial_bcm283x_mu: Flush RX queue after setting baud rate
After the UART was initialized, we may still have bogus data in the RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1 is not set in config.txt.
--- drivers/serial/serial_bcm283x_mu.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)
drivers/serial/serial_bcm283x_mu.c +7 -1
@@ -51,6 +51,8 @@ struct bcm283x_mu_priv {struct bcm283x_mu_regs *regs; }; +static int bcm283x_mu_serial_getc (struct udevice *dev); +static int bcm283x_mu_serial_setbrg (struct udevice *dev,int baudrate) {struct bcm283x_mu_serial_platdata *plat =dev_get_platdata (dev);
@@ -59,13 +61,17 @@ static int bcm283x_mu_serial_setbrg(struct udevice *dev, int baudrate)u32 divider;if (plat->skip_init) -return 0 ; + goto out; divider = plat->clock / (baudrate *8 );writel (BCM283X_MU_LCR_DATA_SIZE_8 , ®s->lcr);writel (divider -1 , ®s->baud); +out: +/* Flush the RX queue - all data in there is bogus */ +while (bcm283x_mu_serial_getc (dev) != -EAGAIN ) ; +return 0 ; }
Signature · 1 line
2.12.3
PATCH 1/2 serial_bcm283x_mu: Flush RX queue after setting baud rate
Quoted 5 lines · Alexander Graf
After the UART was initialized, we may still have bogus data in the RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
Quoted 7 lines
This fixes a regression with the dynamic pinmuxing code when enable_uart=1 is not set in config.txt.
Fixes caf2233b28 ("bcm283x: Add pinctrl driver")Reported-by Göran Lundberg <[email protected]>Reported-by Peter Robinson <[email protected]>Signed-off-by Alexander Graf <[email protected]>
Tested on both 32 bit using extlinux and 64 bit using uEFI boots. The 32 bit one, the one I saw issues with, didn't enable enable_uart because it's attached to HDMI without a serial console, the 64 does have serial console with the option in config.txt
Quoted 39 lines
--- drivers/serial/serial_bcm283x_mu.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)drivers/serial/serial_bcm283x_mu.c +7
-2@@ -51,6 +51,8 @@ struct bcm283x_mu_priv {struct bcm283x_mu_regs *regs; }; +static int bcm283x_mu_serial_getc (struct udevice *dev); +static int bcm283x_mu_serial_setbrg (struct udevice *dev,int baudrate) {struct bcm283x_mu_serial_platdata *plat =dev_get_platdata (dev);@@ -59,13 +61,17 @@ static int bcm283x_mu_serial_setbrg(struct udevice *dev, int baudrate)u32 divider;if (plat->skip_init) -return 0 ; + goto out; divider = plat->clock / (baudrate *8 );writel (BCM283X_MU_LCR_DATA_SIZE_8 , ®s->lcr);writel (divider -1 , ®s->baud); +out: +/* Flush the RX queue - all data in there is bogus */ +while (bcm283x_mu_serial_getc (dev) != -EAGAIN ) ; +return 0 ; } --2.12.3
PATCH 2/2 bcm283x_pl011: Flush RX queue after setting baud rate
In reply to Alexander GrafAfter the UART was initialized, we may still have bogus data in the RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1 is not set in config.txt on Raspberry Pis that use pl011 for serial.
--- drivers/serial/serial_bcm283x_pl011.c | 25 ++++++++++++++++++++++++- drivers/serial/serial_pl01x.c | 10 +++++----- drivers/serial/serial_pl01x_internal.h | 7 ++++++- 3 files changed, 35 insertions(+), 7 deletions(-)
drivers/serial/serial_bcm283x_pl011.c +24 -1
@@ -9,6 +9,7 @@#include <asm/gpio.h> #include <dm/pinctrl.h> #include <dm/platform_data/serial_pl01x.h> +#include <serial.h> #include "serial_pl01x_internal.h" /*
@@ -55,6 +56,28 @@ static int bcm283x_pl011_serial_ofdata_to_platdata(struct udevice *dev)return 0 ; } +static int bcm283x_pl011_serial_setbrg (struct udevice *dev,int baudrate) +{ +int r; + + r =pl01x_serial_setbrg (dev, baudrate); + +/* +* We may have been muxed to a bogus line before. Drain the RX +* queue so we start at a clean slate. +*/ +while (pl01x_serial_getc (dev) == -EAGAIN ) ; + +return r; +} + +static const struct dm_serial_ops bcm283x_pl011_serial_ops = { + .putc = pl01x_serial_putc, + .pending = pl01x_serial_pending, + .getc = pl01x_serial_getc, + .setbrg = bcm283x_pl011_serial_setbrg, +}; +static const struct udevice_id bcm283x_pl011_serial_id[] = { {.compatible ="brcm,bcm2835-pl011" , .data =TYPE_PL011 }, {}
@@ -67,7 +90,7 @@ U_BOOT_DRIVER(bcm283x_pl011_uart) = { .ofdata_to_platdata = of_match_ptr(bcm283x_pl011_serial_ofdata_to_platdata), .platdata_auto_alloc_size = sizeof(struct pl01x_serial_platdata), .probe = pl01x_serial_probe, - .ops = &pl01x_serial_ops, + .ops = &bcm283x_pl011_serial_ops, .flags = DM_FLAG_PRE_RELOC, .priv_auto_alloc_size = sizeof(struct pl01x_priv), };
drivers/serial/serial_pl01x.c +5 -5
@@ -273,7 +273,7 @@ __weak struct serial_device *default_serial_console(void)#ifdef CONFIG_DM_SERIAL -static int pl01x_serial_setbrg (struct udevice *dev,int baudrate) +int pl01x_serial_setbrg (struct udevice *dev,int baudrate) {struct pl01x_serial_platdata *plat =dev_get_platdata (dev);struct pl01x_priv *priv =dev_get_priv (dev);
@@ -299,21 +299,21 @@ int pl01x_serial_probe(struct udevice *dev)return 0 ; } -static int pl01x_serial_getc (struct udevice *dev) +int pl01x_serial_getc (struct udevice *dev) {struct pl01x_priv *priv =dev_get_priv (dev);return pl01x_getc (priv->regs); } -static int pl01x_serial_putc (struct udevice *dev,const char ch) +int pl01x_serial_putc (struct udevice *dev,const char ch) {struct pl01x_priv *priv =dev_get_priv (dev);return pl01x_putc (priv->regs, ch); } -static int pl01x_serial_pending (struct udevice *dev,bool input) +int pl01x_serial_pending (struct udevice *dev,bool input) {struct pl01x_priv *priv =dev_get_priv (dev);unsigned int fr =readl (&priv->regs->fr);
@@ -324,7 +324,7 @@ static int pl01x_serial_pending(struct udevice *dev, bool input)return fr & UART_PL01x_FR_TXFF ?0 :1 ; } -const struct dm_serial_ops pl01x_serial_ops = { +static const struct dm_serial_ops pl01x_serial_ops = { .putc = pl01x_serial_putc, .pending = pl01x_serial_pending, .getc = pl01x_serial_getc,
drivers/serial/serial_pl01x_internal.h +6 -1
@@ -43,7 +43,12 @@ struct pl01x_regs {int pl01x_serial_ofdata_to_platdata (struct udevice *dev);int pl01x_serial_probe (struct udevice *dev); -extern const struct dm_serial_ops pl01x_serial_ops; + +/* Needed for external pl01x_serial_ops drivers */ +int pl01x_serial_putc (struct udevice *dev,const char ch); +int pl01x_serial_pending (struct udevice *dev,bool input); +int pl01x_serial_getc (struct udevice *dev); +int pl01x_serial_setbrg (struct udevice *dev,int baudrate);struct pl01x_priv {struct pl01x_regs *regs;
Signature · 1 line
2.12.3
PATCH 2/2 bcm283x_pl011: Flush RX queue after setting baud rate
Quoted 7 lines · Alexander Graf
After the UART was initialized, we may still have bogus data in the RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1 is not set in config.txt on Raspberry Pis that use pl011 for serial.
This causes my RPi2 devices not to actually boot. When I connected a HDMI monitor to one of them I get the rainbow square.
Peter
Quoted 128 lines
Fixes caf2233b28 ("bcm283x: Add pinctrl driver")Reported-by Göran Lundberg <[email protected]>Reported-by Peter Robinson <[email protected]>Signed-off-by Alexander Graf <[email protected]>--- drivers/serial/serial_bcm283x_pl011.c | 25 ++++++++++++++++++++++++- drivers/serial/serial_pl01x.c | 10 +++++----- drivers/serial/serial_pl01x_internal.h | 7 ++++++- 3 files changed, 35 insertions(+), 7 deletions(-)drivers/serial/serial_bcm283x_pl011.c +24
-1@@ -9,6 +9,7 @@#include <asm/gpio.h> #include <dm/pinctrl.h> #include <dm/platform_data/serial_pl01x.h> +#include <serial.h> #include "serial_pl01x_internal.h" /* @@ -55,6 +56,28 @@ static int bcm283x_pl011_serial_ofdata_to_platdata(struct udevice *dev)return 0 ; } +static int bcm283x_pl011_serial_setbrg (struct udevice *dev,int baudrate) +{ +int r; + + r =pl01x_serial_setbrg (dev, baudrate); + +/* +* We may have been muxed to a bogus line before. Drain the RX +* queue so we start at a clean slate. +*/ +while (pl01x_serial_getc (dev) == -EAGAIN ) ; + +return r; +} + +static const struct dm_serial_ops bcm283x_pl011_serial_ops = { + .putc = pl01x_serial_putc, + .pending = pl01x_serial_pending, + .getc = pl01x_serial_getc, + .setbrg = bcm283x_pl011_serial_setbrg, +}; +static const struct udevice_id bcm283x_pl011_serial_id[] = { {.compatible ="brcm,bcm2835-pl011" , .data =TYPE_PL011 }, {}@@ -67,7 +90,7 @@ U_BOOT_DRIVER(bcm283x_pl011_uart) = { .ofdata_to_platdata = of_match_ptr(bcm283x_pl011_serial_ofdata_to_platdata), .platdata_auto_alloc_size = sizeof(struct pl01x_serial_platdata), .probe = pl01x_serial_probe, - .ops = &pl01x_serial_ops, + .ops = &bcm283x_pl011_serial_ops, .flags = DM_FLAG_PRE_RELOC, .priv_auto_alloc_size = sizeof(struct pl01x_priv), };drivers/serial/serial_pl01x.c +5
-5@@ -273,7 +273,7 @@ __weak struct serial_device *default_serial_console(void)#ifdef CONFIG_DM_SERIAL -static int pl01x_serial_setbrg (struct udevice *dev,int baudrate) +int pl01x_serial_setbrg (struct udevice *dev,int baudrate) {struct pl01x_serial_platdata *plat =dev_get_platdata (dev);struct pl01x_priv *priv =dev_get_priv (dev);@@ -299,21 +299,21 @@ int pl01x_serial_probe(struct udevice *dev)return 0 ; } -static int pl01x_serial_getc (struct udevice *dev) +int pl01x_serial_getc (struct udevice *dev) {struct pl01x_priv *priv =dev_get_priv (dev);return pl01x_getc (priv->regs); } -static int pl01x_serial_putc (struct udevice *dev,const char ch) +int pl01x_serial_putc (struct udevice *dev,const char ch) {struct pl01x_priv *priv =dev_get_priv (dev);return pl01x_putc (priv->regs, ch); } -static int pl01x_serial_pending (struct udevice *dev,bool input) +int pl01x_serial_pending (struct udevice *dev,bool input) {struct pl01x_priv *priv =dev_get_priv (dev);unsigned int fr =readl (&priv->regs->fr);@@ -324,7 +324,7 @@ static int pl01x_serial_pending(struct udevice *dev, bool input)return fr & UART_PL01x_FR_TXFF ?0 :1 ; } -const struct dm_serial_ops pl01x_serial_ops = { +static const struct dm_serial_ops pl01x_serial_ops = { .putc = pl01x_serial_putc, .pending = pl01x_serial_pending, .getc = pl01x_serial_getc,drivers/serial/serial_pl01x_internal.h +6
-2@@ -43,7 +43,12 @@ struct pl01x_regs {int pl01x_serial_ofdata_to_platdata (struct udevice *dev);int pl01x_serial_probe (struct udevice *dev); -extern const struct dm_serial_ops pl01x_serial_ops; + +/* Needed for external pl01x_serial_ops drivers */ +int pl01x_serial_putc (struct udevice *dev,const char ch); +int pl01x_serial_pending (struct udevice *dev,bool input); +int pl01x_serial_getc (struct udevice *dev); +int pl01x_serial_setbrg (struct udevice *dev,int baudrate);struct pl01x_priv {struct pl01x_regs *regs; --2.12.3
PATCH 2/2 bcm283x_pl011: Flush RX queue after setting baud rate
Quoted 11 lines · Peter Robinson
Quoted 7 lines · Alexander Graf
After the UART was initialized, we may still have bogus data in the RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1 is not set in config.txt on Raspberry Pis that use pl011 for serial.
This causes my RPi2 devices not to actually boot. When I connected a HDMI monitor to one of them I get the rainbow square.
Ok, I was able to reproduce this on the RPi3 CM. See below ...
Quoted 30 lines
Peter
Quoted 26 lines
Fixes caf2233b28 ("bcm283x: Add pinctrl driver")Reported-by Göran Lundberg <[email protected]>Reported-by Peter Robinson <[email protected]>Signed-off-by Alexander Graf <[email protected]>--- drivers/serial/serial_bcm283x_pl011.c | 25 ++++++++++++++++++++++++- drivers/serial/serial_pl01x.c | 10 +++++----- drivers/serial/serial_pl01x_internal.h | 7 ++++++- 3 files changed, 35 insertions(+), 7 deletions(-)drivers/serial/serial_bcm283x_pl011.c +1
-0@@ -9,6 +9,7 @@#include <asm/gpio.h> #include <dm/pinctrl.h> #include <dm/platform_data/serial_pl01x.h> +#include <serial.h> #include "serial_pl01x_internal.h" /* @@ -55,6 +56,28 @@ static int bcm283x_pl011_serial_ofdata_to_platdata(struct udevice *dev)return 0 ; }
Quoted 11 lines
drivers/serial/serial_bcm283x_pl011.c static int bcm283x_pl011_serial_ofdata_to_platdata(struct udevice *dev) · line 69
Quoted 11 lines
drivers/serial/serial_bcm283x_pl011.c +11
-0+static int bcm283x_pl011_serial_setbrg (struct udevice *dev,int baudrate) +{ +int r; + + r =pl01x_serial_setbrg (dev, baudrate); + +/* +* We may have been muxed to a bogus line before. Drain the RX +* queue so we start at a clean slate. +*/ +while (pl01x_serial_getc (dev) == -EAGAIN ) ;
... this is obviously wrong. It doesn't drain the queue but instead loops as long as the queue is empty. Bleks.
I'll send a v2. Please retest then. Sorry for the mess :).
Alex
cover RPi: Drain RX queue on setbrg
In reply to Alexander GrafQuoted 10 lines · Alexander Graf
We had a few reports coming in from people that had their autoboot chain aborted after pinmuxing support was added for the RPi.
The culprit is easy: The UARTs may have been enabled before, but muxed to an incorrect pin. That pin may have pulled the RX line down which again lead to lots of zero bytes gathered in the RX buffer.
The easy fix for that is to drain the RX queue every time we set the baud rate.
Quoted 6 lines
This patch set is the minimally intrusive fix for the RPi. We may want to do that generically for all serial devices later.
Alexander Graf (2):
serial_bcm283x_mu: Flush RX queue after setting baud rate
bcm283x_pl011: Flush RX queue after setting baud rate
This causes mixed effects for me, a regression on the RPi2 using the pl011, but fixes the issue on the RPi3. Both my RPi2 have serial console and playing with the enable in config.txt doesn't seem to have any effect on whether they auto boot or not but with it commented out I seem to get more random chars.
Peter
cover RPi: Drain RX queue on setbrg
Quoted 14 lines · Peter Robinson
Quoted 13 lines · Alexander Graf
We had a few reports coming in from people that had their autoboot chain aborted after pinmuxing support was added for the RPi.
The culprit is easy: The UARTs may have been enabled before, but muxed to an incorrect pin. That pin may have pulled the RX line down which again lead to lots of zero bytes gathered in the RX buffer.
The easy fix for that is to drain the RX queue every time we set the baud rate.
This patch set is the minimally intrusive fix for the RPi. We may want to do that generically for all serial devices later.
Quoted 8 lines
Quoted 3 lines
Alexander Graf (2):
serial_bcm283x_mu: Flush RX queue after setting baud rate
bcm283x_pl011: Flush RX queue after setting baud rateThis causes mixed effects for me, a regression on the RPi2 using the pl011, but fixes the issue on the RPi3. Both my RPi2 have serial console and playing with the enable in config.txt doesn't seem to have any effect on whether they auto boot or not but with it commented out I seem to get more random chars.
Thanks a lot for testing! I'll try it on a rpi2 later tonight and check why it's failing.
Alex