Skip to contentSkip to conversation

imx: board: Add support for the K+P's kp_imx6q_tpc board

PATCH Superseded Lukasz Majewski 2 participants 5 messages Mar 14, 2018 – Mar 29, 2018

Subsystems (3)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 imx: board: Add support for the K+P's kp_imx6q_tpc board

This commit provides support for Kieback & Peter GmbH IMX6Q based TPC board.

---

 arch/arm/mach-imx/mx6/Kconfig             |  11 ++
 board/k+p/kp_imx6q_tpc/Kconfig            |  12 ++
 board/k+p/kp_imx6q_tpc/MAINTAINERS        |   6 +
 board/k+p/kp_imx6q_tpc/Makefile           |  11 ++
 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c     | 302 ++++++++++++++++++++++++++++++
 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c | 283 ++++++++++++++++++++++++++++
 configs/kp_imx6q_tpc_defconfig            |  42 +++++
 include/configs/kp_imx6q_tpc.h            | 128 +++++++++++++
 8 files changed, 795 insertions(+)
 create mode 100644 board/k+p/kp_imx6q_tpc/Kconfig
 create mode 100644 board/k+p/kp_imx6q_tpc/MAINTAINERS
 create mode 100644 board/k+p/kp_imx6q_tpc/Makefile
 create mode 100644 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c
 create mode 100644 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c
 create mode 100644 configs/kp_imx6q_tpc_defconfig
 create mode 100644 include/configs/kp_imx6q_tpc.h
arch/arm/mach-imx/mx6/Kconfig +11 -0
index d4ce38db8d..aa6f5facbf 100644
@@ -387,6 +387,16 @@ config TARGET_TBS2910
 config TARGET_TITANIUM
 	bool "titanium"
 
+config TARGET_KP_IMX6Q_TPC
+	bool "K+P KP_IMX6Q_TPC i.MX6 Quad"
+	select MX6QDL
+	select BOARD_LATE_INIT
+	select BOARD_EARLY_INIT_F
+	select SUPPORT_SPL
+	select DM
+	select DM_THERMAL
+	imply CMD_SPL
+
 config TARGET_TQMA6
 	bool "TQ Systems TQMa6 board"
 	select BOARD_LATE_INIT
@@ -493,6 +503,7 @@ source "board/tbs/tbs2910/Kconfig"
 source "board/tqc/tqma6/Kconfig"
 source "board/toradex/apalis_imx6/Kconfig"
 source "board/toradex/colibri_imx6/Kconfig"
+source "board/k+p/kp_imx6q_tpc/Kconfig"
 source "board/udoo/Kconfig"
 source "board/udoo/neo/Kconfig"
 source "board/wandboard/Kconfig"
board/k+p/kp_imx6q_tpc/Kconfig new file +12 -0
new file mode 100644
index 0000000000..62e34978ec
@@ -0,0 +1,12 @@
+if TARGET_KP_IMX6Q_TPC
+
+config SYS_BOARD
+	default "kp_imx6q_tpc"
+
+config SYS_VENDOR
+	default "k+p"
+
+config SYS_CONFIG_NAME
+	default "kp_imx6q_tpc"
+
+endif
board/k+p/kp_imx6q_tpc/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..6c4c8dd28e
@@ -0,0 +1,6 @@
+KP_IMX6Q_TPC BOARD
+M:	Lukasz Majewski <[email protected]>
+S:	Maintained
+F:	board/k+p/kp_imx6q_tpc/
+F:	include/configs/kp_imx6q_tpc.h
+F:	configs/kp_imx6q_tpc_defconfig
board/k+p/kp_imx6q_tpc/Makefile new file +11 -0
new file mode 100644
index 0000000000..51cbd3e843
@@ -0,0 +1,11 @@
+#
+# Copyright (C) 2018 Lukasz Majewski <[email protected]>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y	:= kp_imx6q_tpc_spl.o
+else
+obj-y	:= kp_imx6q_tpc.o
+endif
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +302 -0

302 lines not on this page · raw message

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +283 -0

283 lines not on this page · raw message

configs/kp_imx6q_tpc_defconfig new file +42 -0

42 lines not on this page · raw message

include/configs/kp_imx6q_tpc.h new file +128 -0

128 lines not on this page · raw message

Signature · 1 line
2.11.0
#1 lore raw

PATCH 2/2 boot: script: The boot.scr file for K+P's boards

By using this file one can avoid cluttering <board>.h file with u-boot HUSH commands necessary for booting target device.

With such approach the commands are stored only in one place and can be reused if needed.

---

 board/k+p/bootscripts/tpcboot.cmd | 96 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 96 insertions(+)
 create mode 100644 board/k+p/bootscripts/tpcboot.cmd
board/k+p/bootscripts/tpcboot.cmd new file +96 -0
new file mode 100644
index 0000000000..f6d59a1186
@@ -0,0 +1,96 @@
+#
+# Copyright (C) 2018
+# Lukasz Majewski, DENX Software Engineering, lukma at denx.de
+#
+#
+# This is an example file to generate boot.scr - a boot script for U-Boot
+# Generate boot.scr:
+# ./tools/mkimage -c none -A arm -T script -d tpcboot.cmd boot.scr
+#
+# SPDX-License-Identifier:	GPL-2.0+
+
+
+# Input envs (to be set in environment)
+# Mandatory:
+# kernel_file = "fitImage"
+# boardname = "XXXX"  // set automatically in u-boot
+# boardsoc = "imx6q"  // set automatically in u-boot
+#
+# Optional:
+# bootcmd_force = "nfs" "tftp_kernel"
+# If not set - eMMC/SD boot
+
+# Generic setup
+setenv mmcroot "/dev/mmcblk${devnum}p2 rootwait rw"
+setenv displayargs ""
+setenv mmcargs "setenv bootargs console=${console} ${smp} root=${mmcroot} \
+	${displayargs}"
+setenv boot_fitImage "
+	setenv fdt_conf 'conf@${boardsoc}-${boardname}.dtb';
+	setenv itbcfg "\"#\${fdt_conf}\"";
+	print itbcfg;
+	bootm '${loadaddr}${itbcfg}';"
+
+#------------------------------------------------------------
+#
+# Provide default 'bootcmd' command
+#------------------------------------------------------------
+setenv bootcmd "
+if test -e ${devtype} ${devnum}:${distro_bootpart} ${kernel_file}; then
+	echo Found kernel image: ${kernel_file};
+	if load ${devtype} ${devnum}:${distro_bootpart} ${loadaddr} \
+	   ${kernel_file}; then
+		run mmcargs;
+		run boot_fitImage;
+	fi;
+fi;"
+
+#------------------------------------------------------------
+#
+# Provide 'boot_tftp_kernel' command
+#------------------------------------------------------------
+setenv download_kernel "tftpboot ${loadaddr} ${kernel_file}"
+
+setenv boot_tftp_kernel "
+if run download_kernel; then
+	run mmcargs;
+	run boot_fitImage;
+fi"
+
+#------------------------------------------------------------
+#
+# Provide 'boot_nfs' command
+#------------------------------------------------------------
+setenv rootpath "/srv/tftp/KP/rootfs"
+setenv nfsargs "setenv bootargs root=/dev/nfs rw \
+       nfsroot=${serverip}:${rootpath},nolock,nfsvers=3"
+setenv addip "setenv bootargs ${bootargs} \
+       ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:\
+       ${hostname}:eth0:on"
+
+setenv boot_nfs "
+if run download_kernel; then
+	run nfsargs;
+	run addip;
+	setenv bootargs ${bootargs} console=${console};
+
+	run boot_fitImage;
+fi"
+
+#------------------------------------------------------------
+#
+# Set correct boot flow
+#------------------------------------------------------------
+
+setenv bcmd "
+if test ! -n ${bootcmd_force}; then
+	run bootcmd;
+fi;
+if test ${bootcmd_force} = nfs; then
+	run boot_nfs;
+else if test ${bootcmd_force} = tftp_kernel; then
+	run boot_tftp_kernel;
+     fi;
+fi"
+
+run bcmd
Signature · 1 line
2.11.0
#2 lore raw

PATCH 2/2 boot: script: The boot.scr file for K+P's boards

Quoted 107 lines · Lukasz Majewski

By using this file one can avoid cluttering <board>.h file with u-boot HUSH commands necessary for booting target device.

With such approach the commands are stored only in one place and can be reused if needed.

---

 board/k+p/bootscripts/tpcboot.cmd | 96 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 96 insertions(+)
 create mode 100644 board/k+p/bootscripts/tpcboot.cmd
board/k+p/bootscripts/tpcboot.cmd new file +86 -0
new file mode 100644
index 0000000000..f6d59a1186
@@ -0,0 +1,96 @@
+#
+# Copyright (C) 2018
+# Lukasz Majewski, DENX Software Engineering, lukma at denx.de
+#
+#
+# This is an example file to generate boot.scr - a boot script for U-Boot
+# Generate boot.scr:
+# ./tools/mkimage -c none -A arm -T script -d tpcboot.cmd boot.scr
+#
+# SPDX-License-Identifier:	GPL-2.0+
+
+
+# Input envs (to be set in environment)
+# Mandatory:
+# kernel_file = "fitImage"
+# boardname = "XXXX"  // set automatically in u-boot
+# boardsoc = "imx6q"  // set automatically in u-boot
+#
+# Optional:
+# bootcmd_force = "nfs" "tftp_kernel"
+# If not set - eMMC/SD boot
+
+# Generic setup
+setenv mmcroot "/dev/mmcblk${devnum}p2 rootwait rw"
+setenv displayargs ""
+setenv mmcargs "setenv bootargs console=${console} ${smp} root=${mmcroot} \
+	${displayargs}"
+setenv boot_fitImage "
+	setenv fdt_conf 'conf@${boardsoc}-${boardname}.dtb';
+	setenv itbcfg "\"#\${fdt_conf}\"";
+	print itbcfg;
+	bootm '${loadaddr}${itbcfg}';"
+
+#------------------------------------------------------------
+#
+# Provide default 'bootcmd' command
+#------------------------------------------------------------
+setenv bootcmd "
+if test -e ${devtype} ${devnum}:${distro_bootpart} ${kernel_file}; then
+	echo Found kernel image: ${kernel_file};
+	if load ${devtype} ${devnum}:${distro_bootpart} ${loadaddr} \
+	   ${kernel_file}; then
+		run mmcargs;
+		run boot_fitImage;
+	fi;
+fi;"
+
+#------------------------------------------------------------
+#
+# Provide 'boot_tftp_kernel' command
+#------------------------------------------------------------
+setenv download_kernel "tftpboot ${loadaddr} ${kernel_file}"
+
+setenv boot_tftp_kernel "
+if run download_kernel; then
+	run mmcargs;
+	run boot_fitImage;
+fi"
+
+#------------------------------------------------------------
+#
+# Provide 'boot_nfs' command
+#------------------------------------------------------------
+setenv rootpath "/srv/tftp/KP/rootfs"
+setenv nfsargs "setenv bootargs root=/dev/nfs rw \
+       nfsroot=${serverip}:${rootpath},nolock,nfsvers=3"
+setenv addip "setenv bootargs ${bootargs} \
+       ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:\
+       ${hostname}:eth0:on"
+
+setenv boot_nfs "
+if run download_kernel; then
+	run nfsargs;
+	run addip;
+	setenv bootargs ${bootargs} console=${console};
+
+	run boot_fitImage;
+fi"
+
+#------------------------------------------------------------
+#
+# Set correct boot flow
+#------------------------------------------------------------
+
+setenv bcmd "
+if test ! -n ${bootcmd_force}; then

board/k+p/bootscripts/tpcboot.cmd line 96

Quoted 10 lines
board/k+p/bootscripts/tpcboot.cmd new file +10 -0
+	run bootcmd;
+fi;
+if test ${bootcmd_force} = nfs; then
+	run boot_nfs;
+else if test ${bootcmd_force} = tftp_kernel; then
+	run boot_tftp_kernel;
+     fi;
+fi"
+
+run bcmd

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#3 lore raw

PATCH 1/2 imx: board: Add support for the K+P's kp_imx6q_tpc board

In reply to Lukasz Majewski

Hi Lukasz,

Quoted 3 lines · Lukasz Majewski

This commit provides support for Kieback & Peter GmbH IMX6Q based TPC board.

Maybe you can add the U-Boot output (as done by other boards) to make clear which peripherals are available.

Quoted 513 lines

---

 arch/arm/mach-imx/mx6/Kconfig             |  11 ++
 board/k+p/kp_imx6q_tpc/Kconfig            |  12 ++
 board/k+p/kp_imx6q_tpc/MAINTAINERS        |   6 +
 board/k+p/kp_imx6q_tpc/Makefile           |  11 ++
 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c     | 302 ++++++++++++++++++++++++++++++
 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c | 283 ++++++++++++++++++++++++++++
 configs/kp_imx6q_tpc_defconfig            |  42 +++++
 include/configs/kp_imx6q_tpc.h            | 128 +++++++++++++
 8 files changed, 795 insertions(+)
 create mode 100644 board/k+p/kp_imx6q_tpc/Kconfig
 create mode 100644 board/k+p/kp_imx6q_tpc/MAINTAINERS
 create mode 100644 board/k+p/kp_imx6q_tpc/Makefile
 create mode 100644 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c
 create mode 100644 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c
 create mode 100644 configs/kp_imx6q_tpc_defconfig
 create mode 100644 include/configs/kp_imx6q_tpc.h
arch/arm/mach-imx/mx6/Kconfig +11 -0
index d4ce38db8d..aa6f5facbf 100644
@@ -387,6 +387,16 @@ config TARGET_TBS2910
 config TARGET_TITANIUM
 	bool "titanium"
 
+config TARGET_KP_IMX6Q_TPC
+	bool "K+P KP_IMX6Q_TPC i.MX6 Quad"
+	select MX6QDL
+	select BOARD_LATE_INIT
+	select BOARD_EARLY_INIT_F
+	select SUPPORT_SPL
+	select DM
+	select DM_THERMAL
+	imply CMD_SPL
+
 config TARGET_TQMA6
 	bool "TQ Systems TQMa6 board"
 	select BOARD_LATE_INIT
@@ -493,6 +503,7 @@ source "board/tbs/tbs2910/Kconfig"
 source "board/tqc/tqma6/Kconfig"
 source "board/toradex/apalis_imx6/Kconfig"
 source "board/toradex/colibri_imx6/Kconfig"
+source "board/k+p/kp_imx6q_tpc/Kconfig"
 source "board/udoo/Kconfig"
 source "board/udoo/neo/Kconfig"
 source "board/wandboard/Kconfig"
board/k+p/kp_imx6q_tpc/Kconfig new file +12 -0
new file mode 100644
index 0000000000..62e34978ec
@@ -0,0 +1,12 @@
+if TARGET_KP_IMX6Q_TPC
+
+config SYS_BOARD
+	default "kp_imx6q_tpc"
+
+config SYS_VENDOR
+	default "k+p"
+
+config SYS_CONFIG_NAME
+	default "kp_imx6q_tpc"
+
+endif
board/k+p/kp_imx6q_tpc/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..6c4c8dd28e
@@ -0,0 +1,6 @@
+KP_IMX6Q_TPC BOARD
+M:	Lukasz Majewski <[email protected]>
+S:	Maintained
+F:	board/k+p/kp_imx6q_tpc/
+F:	include/configs/kp_imx6q_tpc.h
+F:	configs/kp_imx6q_tpc_defconfig
board/k+p/kp_imx6q_tpc/Makefile new file +11 -0
new file mode 100644
index 0000000000..51cbd3e843
@@ -0,0 +1,11 @@
+#
+# Copyright (C) 2018 Lukasz Majewski <[email protected]>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y	:= kp_imx6q_tpc_spl.o
+else
+obj-y	:= kp_imx6q_tpc.o
+endif
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +302 -0
new file mode 100644
index 0000000000..9a5b88029f
@@ -0,0 +1,302 @@
+/*
+ * K+P iMX6Q KP_IMX6Q_TPC board configuration
+ *
+ * Copyright (C) 2018 Lukasz Majewski <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <errno.h>
+#include <fsl_esdhc.h>
+#include <fuse.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <mmc.h>
+#include <net.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define ENET_PAD_CTRL							\
+	(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |	\
+	 PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL							\
+	(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |	\
+	PAD_CTL_HYS | PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define PC			MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+static struct i2c_pads_info kp_imx6q_tpc_i2c_pad_info0 = {
+	.scl = {
+		.i2c_mode  = MX6Q_PAD_CSI0_DAT9__I2C1_SCL | PC,
+		.gpio_mode = MX6Q_PAD_CSI0_DAT9__GPIO5_IO27 | PC,
+		.gp = IMX_GPIO_NR(5, 27)
+	},
+	.sda = {
+		 .i2c_mode = MX6Q_PAD_CSI0_DAT8__I2C1_SDA | PC,
+		 .gpio_mode = MX6Q_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
+		 .gp = IMX_GPIO_NR(5, 26)
+	}
+};
+
+static struct i2c_pads_info kp_imx6q_tpc_i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode  = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC,
+		.gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | PC,
+		.gp = IMX_GPIO_NR(4, 12)
+	},
+	.sda = {
+		 .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC,
+		 .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC,
+		 .gp = IMX_GPIO_NR(4, 13)
+	}
+};
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+	return 0;
+}
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const enet_pads[] = {
+	IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_ENET_MDC__ENET_MDC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL |
+		   MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL |
+		   MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	/* AR8031 PHY Reset */
+	IOMUX_PADS(PAD_ENET_CRS_DV__GPIO1_IO25	| MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+static void eth_phy_reset(void)
+{
+	/* Reset AR8031 PHY */
+	gpio_direction_output(IMX_GPIO_NR(1, 25), 0);
+	mdelay(10);
+	gpio_set_value(IMX_GPIO_NR(1, 25), 1);
+	udelay(100);
+}
+
+static int setup_fec_clock(void)
+{
+	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+	/* set gpr1[21] to select anatop clock */
+	clrsetbits_le32(&iomuxc_regs->gpr[1], 0x1 << 21, 0x1 << 21);
+
+	return enable_fec_anatop_clock(0, ENET_50MHZ);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	SETUP_IOMUX_PADS(enet_pads);
+	setup_fec_clock();
+	eth_phy_reset();
+
+	return cpu_eth_init(bis);
+}
+
+static int ar8031_phy_fixup(struct phy_device *phydev)
+{
+	unsigned short val;
+
+	/* To enable AR8031 output a 125MHz clk from CLK_25M */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+	val &= 0xffe3;
+	val |= 0x18;
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+	/* introduce tx clock delay */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+	val |= 0x0100;
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	ar8031_phy_fixup(phydev);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FSL_ESDHC
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{ USDHC2_BASE_ADDR },
+	{ USDHC4_BASE_ADDR },
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		return !gpio_get_value(USDHC2_CD_GPIO);
+	case USDHC4_BASE_ADDR:
+		return 1; /* eMMC/uSDHC4 is always present */
+	}
+
+	return 0;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0                    micro SD
+	 * mmc2                    eMMC
+	 */
+	gpio_direction_input(USDHC2_CD_GPIO);
+
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_USB_EHCI_MX6
+static void setup_usb(void)
+{
+	/*
+	 * Set daisy chain for otg_pin_id on MX6Q.
+	 * For MX6DL, this bit is reserved.
+	 */
+	imx_iomux_set_gpr_register(1, 13, 1, 0);
+}
+
+int board_usb_phy_mode(int port)
+{
+	if (port == 1)
+		return USB_INIT_HOST;
+	else
+		return USB_INIT_DEVICE;
+}
+
+int board_ehci_power(int port, int on)
+{
+	switch (port) {
+	case 0:
+		break;
+	case 1:
+		gpio_direction_output(IMX_GPIO_NR(3, 31), !!on);
+		break;
+	default:
+		printf("MXC USB port %d not yet supported\n", port);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+#endif
+
+int board_early_init_f(void)
+{
+#ifdef CONFIG_USB_EHCI_MX6
+	setup_usb();
+#endif
+
+	return 0;
+}
+
+int board_init(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	/* Enable eim_slow clocks */
+	setbits_le32(&mxc_ccm->CCGR6, 0x1 << MXC_CCM_CCGR6_EMI_SLOW_OFFSET);
+
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &kp_imx6q_tpc_i2c_pad_info0);
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &kp_imx6q_tpc_i2c_pad_info1);
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd2",  MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+	/* 8 bit bus width */
+	{"emmc", MAKE_CFGVAL(0x60, 0x58, 0x00, 0x00)},
+	{NULL,	 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+	env_set("boardname", "kp-tpc");
+	env_set("boardsoc", "imx6q");
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: K+P KP_IMX6Q_TPC i.MX6Q\n");
+	return 0;
+}
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +102 -0
new file mode 100644
index 0000000000..b5723b41c1
@@ -0,0 +1,283 @@
+/*
+ * K+P iMX6Q KP_IMX6Q_TPC board configuration
+ *
+ * Copyright (C) 2018 Lukasz Majewski <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <fuse.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <spl.h>
+
+#define UART_PAD_CTRL							\
+	(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |	\
+	 PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL							\
+	(PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |	\
+	 PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0x00C03F3F, &ccm->CCGR0);
+	writel(0x0030FC03, &ccm->CCGR1);
+	writel(0x0FFFC000, &ccm->CCGR2);
+	writel(0x3FF00000, &ccm->CCGR3);
+	writel(0x00FFF300, &ccm->CCGR4);
+	writel(0x0F0000C3, &ccm->CCGR5);
+	writel(0x000003FF, &ccm->CCGR6);
+}
+
+/* onboard microSD */
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_NANDF_CS3__GPIO6_IO16	| MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+/* eMMC */
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+	IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD4_CLK__SD4_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD4_CMD__SD4_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL)),
+};
+
+/* SD */
+static void setup_iomux_sd(void)
+{
+	SETUP_IOMUX_PADS(usdhc2_pads);
+	SETUP_IOMUX_PADS(usdhc4_pads);
+}
+
+/* UART */
+static iomux_v3_cfg_t const uart1_pads[] = {
+	IOMUX_PADS(PAD_SD3_DAT7__UART1_TX_DATA	| MUX_PAD_CTRL(UART_PAD_CTRL)),
+	IOMUX_PADS(PAD_SD3_DAT6__UART1_RX_DATA	| MUX_PAD_CTRL(UART_PAD_CTRL)),
+};
+
+static void setup_iomux_uart(void)
+{
+	SETUP_IOMUX_PADS(uart1_pads);
+}
+
+/* USB */
+static iomux_v3_cfg_t const usb_pads[] = {
+	IOMUX_PADS(PAD_GPIO_1__USB_OTG_ID	| MUX_PAD_CTRL(NO_PAD_CTRL)),
+	IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31	| MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+static void setup_iomux_usb(void)
+{

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c line 112

Quoted 10 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +10 -0
+	SETUP_IOMUX_PADS(usb_pads);
+}
+
+/*
+ * This code has been extracted from mx6q_8x_mt41K256.cfg DCD
+ * NXP's BSP u-boot mx6q_8x_mt41K256.cfg rel_imx_4.1.15_2.1.0_ga
+ */
+static int mx6q_dcd_table[] = {
+	0x020e0798, 0x000C0000,
+	0x020e0758, 0x00000000,

Well.....

This is a Quad, well supported, we have a nice framework to setup the DDR. I do not like to see this dump of table in code. Which is the added value compared to the DCD table using the i.MX header ?

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c line 122

Quoted 10 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +10 -0
+	0x020e0588, 0x00000030,
+	0x020e0594, 0x00000030,
+	0x020e056c, 0x00000030,
+	0x020e0578, 0x00000030,
+	0x020e074c, 0x00000030,
+	0x020e057c, 0x00000030,
+	0x020e058c, 0x00000000,
+	0x020e059c, 0x00000030,
+	0x020e05a0, 0x00000030,
+	0x020e078c, 0x00000030,

There are structure and function to set these.

Quoted 37 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +37 -0
+	0x020e0750, 0x00020000,
+	0x020e05a8, 0x00000018,
+	0x020e05b0, 0x00000018,
+	0x020e0524, 0x00000018,
+	0x020e051c, 0x00000018,
+	0x020e0518, 0x00000018,
+	0x020e050c, 0x00000018,
+	0x020e05b8, 0x00000018,
+	0x020e05c0, 0x00000018,
+	0x020e0774, 0x00020000,
+	0x020e0784, 0x00000018,
+	0x020e0788, 0x00000018,
+	0x020e0794, 0x00000018,
+	0x020e079c, 0x00000018,
+	0x020e07a0, 0x00000018,
+	0x020e07a4, 0x00000018,
+	0x020e07a8, 0x00000018,
+	0x020e0748, 0x00000018,
+	0x020e05ac, 0x00000018,
+	0x020e05b4, 0x00000018,
+	0x020e0528, 0x00000018,
+	0x020e0520, 0x00000018,
+	0x020e0514, 0x00000018,
+	0x020e0510, 0x00000018,
+	0x020e05bc, 0x00000018,
+	0x020e05c4, 0x00000018,
+	0x021b0800, 0xa1390003,
+	0x021b080c, 0x001F001F,
+	0x021b0810, 0x001F001F,
+	0x021b480c, 0x001F001F,
+	0x021b4810, 0x001F001F,
+	0x021b083c, 0x43270338,
+	0x021b0840, 0x03200314,
+	0x021b483c, 0x431A032F,
+	0x021b4840, 0x03200263,
+	0x021b0848, 0x4B434748,
+	0x021b4848, 0x4445404C,

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c line 169

Quoted 10 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +10 -0
+	0x021b0850, 0x38444542,
+	0x021b4850, 0x4935493A,
+	0x021b081c, 0x33333333,
+	0x021b0820, 0x33333333,
+	0x021b0824, 0x33333333,
+	0x021b0828, 0x33333333,
+	0x021b481c, 0x33333333,
+	0x021b4820, 0x33333333,
+	0x021b4824, 0x33333333,
+	0x021b4828, 0x33333333,

Like calibration and so on. Please change this as done by other board, using structures ( mx6_ddr3_cfg, mx6dq_iomux_grp_regs) and calling mx6dq_dram_iocfg() and mx6_dram_cfg() - thanks !

Quoted 22 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +22 -0
+	0x021b08b8, 0x00000800,
+	0x021b48b8, 0x00000800,
+	0x021b0004, 0x00020036,
+	0x021b0008, 0x09444040,
+	0x021b000c, 0x8A8F7955,
+	0x021b0010, 0xFF328F64,
+	0x021b0014, 0x01FF00DB,
+	0x021b0018, 0x00001740,
+	0x021b001c, 0x00008000,
+	0x021b002c, 0x000026d2,
+	0x021b0030, 0x008F1023,
+	0x021b0040, 0x00000047,
+	0x021b0000, 0x841A0000,
+	0x021b001c, 0x04088032,
+	0x021b001c, 0x00008033,
+	0x021b001c, 0x00048031,
+	0x021b001c, 0x09408030,
+	0x021b001c, 0x04008040,
+	0x021b0020, 0x00005800,
+	0x021b0818, 0x00011117,
+	0x021b4818, 0x00011117,
+	0x021b0004, 0x00025576,

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c line 201

Quoted 10 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +10 -0
+	0x021b0404, 0x00011006,
+	0x021b001c, 0x00000000,
+};
+
+static void ddr_init(int *table, int size)
+{
+	int i;
+
+	for (i = 0; i < size / 2 ; i++)
+		writel(table[2 * i + 1], table[2 * i]);

Quite nasty....

Quoted 255 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +82 -0
+}
+
+struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{USDHC2_BASE_ADDR},
+	{USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	case USDHC4_BASE_ADDR:
+		ret = 1; /* eMMC/uSDHC4 is always present */
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bd)
+{
+	struct src *psrc = (struct src *)SRC_BASE_ADDR;
+	unsigned int reg = readl(&psrc->sbmr1) >> 11;
+	/*
+	 * Upon reading BOOT_CFG register the following map is done:
+	 * Bit 11 and 12 of BOOT_CFG register can determine the current
+	 * mmc port
+	 * 0x1                  SD1
+	 * 0x3                  SD4
+	 */
+
+	switch (reg & 0x3) {
+	case 0x1:
+		SETUP_IOMUX_PADS(usdhc2_pads);
+		usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	case 0x3:
+		SETUP_IOMUX_PADS(usdhc4_pads);
+		usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	}
+
+	return fsl_esdhc_initialize(bd, &usdhc_cfg[0]);
+}
+
+void board_init_f(ulong dummy)
+{
+	/* Setup DDR3 from NXP's BSP DCD file */
+	ddr_init(mx6q_dcd_table, ARRAY_SIZE(mx6q_dcd_table));
+
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+	gpr_init();
+
+	/* setup GP timer */
+	timer_init();
+
+	setup_iomux_sd();
+	setup_iomux_uart();
+	setup_iomux_usb();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
configs/kp_imx6q_tpc_defconfig new file +42 -0
new file mode 100644
index 0000000000..d2c6e2e6ba
@@ -0,0 +1,42 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x17800000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_MX6_DDRCAL=y
+CONFIG_TARGET_KP_IMX6Q_TPC=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
+# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
+CONFIG_SPL=y
+CONFIG_SPL_RAW_IMAGE_SUPPORT=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_STOP_STR="."
+# CONFIG_CMD_BOOTEFI_HELLO_COMPILE is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT4_WRITE=y
+# CONFIG_ISO_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_NETDEVICES=y
+CONFIG_FEC_MXC=y
+CONFIG_IMX_THERMAL=y
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_OF_LIBFDT=y
include/configs/kp_imx6q_tpc.h new file +118 -0
new file mode 100644
index 0000000000..74143a2dba
@@ -0,0 +1,128 @@
+/*
+ * K+P iMX6Q KP_IMX6Q_TPC board configuration
+ *
+ * Copyright (C) 2018 Lukasz Majewski <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __KP_IMX6Q_TPC_IMX6_CONFIG_H_
+#define __KP_IMX6Q_TPC_IMX6_CONFIG_H_
+
+#include <asm/arch/imx-regs.h>
+
+#include "mx6_common.h"
+
+/* SPL */
+#include "imx6_spl.h"			/* common IMX6 SPL configuration */
+
+/* Miscellaneous configurable options */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+#define CONFIG_BOUNCE_BUFFER
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(4 * SZ_1M)
+
+/* FEC ethernet */
+#define CONFIG_MII
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_ETHPRIME			"FEC"
+#define CONFIG_FEC_MXC_PHYADDR		0
+#define CONFIG_ARP_TIMEOUT		200UL
+
+/* Fuses */
+#ifdef CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+#endif
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+#define CONFIG_SYS_MMC_ENV_DEV		1 /* 0 = SDHC2, 1 = SDHC4 (eMMC) */
+
+/* UART */
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+
+/* USB Configs */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS		0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT	2 /* Enabled USB controller number */
+#endif
+
+/* Watchdog */
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT_MSECS	60000
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_LOADADDR			0x12000000
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS	\
+	"console=ttymxc0,115200\0"	\
+	"fdt_addr=0x18000000\0"		\
+	"fdt_high=0xffffffff\0"		\
+	"initrd_high=0xffffffff\0"	\
+	"kernel_addr_r=0x10008000\0"	\
+	"fdt_addr_r=0x13000000\0"	\
+	"ramdisk_addr_r=0x18000000\0"	\
+	"scriptaddr=0x14000000\0"	\
+	"kernel_file=fitImage\0"\
+	BOOTENV
+
+#define CONFIG_BOOTCOMMAND		"run distro_bootcmd"
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 0) \
+	func(MMC, mmc, 1) \
+	func(USB, usb, 0) \
+	func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+#endif
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+

include/configs/kp_imx6q_tpc.h line 128

Quoted 10 lines
include/configs/kp_imx6q_tpc.h new file +10 -0
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* Environment */
+#define CONFIG_ENV_SIZE	(SZ_8K)
+#define CONFIG_ENV_OFFSET       0x100000
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+
+#endif	/* __KP_IMX6Q_TPC_IMX6_CONFIG_H_ */

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#4 lore raw

PATCH 1/2 imx: board: Add support for the K+P's kp_imx6q_tpc board

Hi Stefano,

Quoted 9 lines

Hi Lukasz,

Quoted 3 lines · Lukasz Majewski

This commit provides support for Kieback & Peter GmbH IMX6Q based TPC board.

Maybe you can add the U-Boot output (as done by other boards) to make clear which peripherals are available.

Ok.

Quoted 574 lines
Quoted 561 lines

---

 arch/arm/mach-imx/mx6/Kconfig             |  11 ++
 board/k+p/kp_imx6q_tpc/Kconfig            |  12 ++
 board/k+p/kp_imx6q_tpc/MAINTAINERS        |   6 +
 board/k+p/kp_imx6q_tpc/Makefile           |  11 ++
 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c     | 302

++++++++++++++++++++++++++++++
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c | 283
++++++++++++++++++++++++++++
configs/kp_imx6q_tpc_defconfig | 42 +++++
include/configs/kp_imx6q_tpc.h | 128 +++++++++++++ 8
files changed, 795 insertions(+) create mode 100644 board/k+p/kp_imx6q_tpc/Kconfig create mode 100644 board/k+p/kp_imx6q_tpc/MAINTAINERS create mode 100644 board/k+p/kp_imx6q_tpc/Makefile create mode 100644 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c create mode 100644 board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c create mode 100644 configs/kp_imx6q_tpc_defconfig create mode 100644 include/configs/kp_imx6q_tpc.h

(quoted diff) +0 -0

b/arch/arm/mach-imx/mx6/Kconfig index d4ce38db8d..aa6f5facbf 100644

arch/arm/mach-imx/mx6/Kconfig +11 -0
@@ -387,6 +387,16 @@ config TARGET_TBS2910
 config TARGET_TITANIUM
 	bool "titanium"
 
+config TARGET_KP_IMX6Q_TPC
+	bool "K+P KP_IMX6Q_TPC i.MX6 Quad"
+	select MX6QDL
+	select BOARD_LATE_INIT
+	select BOARD_EARLY_INIT_F
+	select SUPPORT_SPL
+	select DM
+	select DM_THERMAL
+	imply CMD_SPL
+
 config TARGET_TQMA6
 	bool "TQ Systems TQMa6 board"
 	select BOARD_LATE_INIT
@@ -493,6 +503,7 @@ source "board/tbs/tbs2910/Kconfig"
 source "board/tqc/tqma6/Kconfig"
 source "board/toradex/apalis_imx6/Kconfig"
 source "board/toradex/colibri_imx6/Kconfig"
+source "board/k+p/kp_imx6q_tpc/Kconfig"
 source "board/udoo/Kconfig"
 source "board/udoo/neo/Kconfig"
 source "board/wandboard/Kconfig"
(quoted diff) +0 -0

b/board/k+p/kp_imx6q_tpc/Kconfig new file mode 100644 index 0000000000..62e34978ec

board/k+p/kp_imx6q_tpc/Kconfig new file +12 -0
@@ -0,0 +1,12 @@
+if TARGET_KP_IMX6Q_TPC
+
+config SYS_BOARD
+	default "kp_imx6q_tpc"
+
+config SYS_VENDOR
+	default "k+p"
+
+config SYS_CONFIG_NAME
+	default "kp_imx6q_tpc"
+
+endif
(quoted diff) +0 -0

b/board/k+p/kp_imx6q_tpc/MAINTAINERS new file mode 100644 index 0000000000..6c4c8dd28e

board/k+p/kp_imx6q_tpc/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@
+KP_IMX6Q_TPC BOARD
+M:	Lukasz Majewski <[email protected]>
+S:	Maintained
+F:	board/k+p/kp_imx6q_tpc/
+F:	include/configs/kp_imx6q_tpc.h
+F:	configs/kp_imx6q_tpc_defconfig
(quoted diff) +0 -0

b/board/k+p/kp_imx6q_tpc/Makefile new file mode 100644 index 0000000000..51cbd3e843

board/k+p/kp_imx6q_tpc/Makefile new file +11 -0
@@ -0,0 +1,11 @@
+#
+# Copyright (C) 2018 Lukasz Majewski <[email protected]>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y	:= kp_imx6q_tpc_spl.o
+else
+obj-y	:= kp_imx6q_tpc.o
+endif
(quoted diff) +0 -0

b/board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file mode 100644 index 0000000000..9a5b88029f

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +34 -0
@@ -0,0 +1,302 @@
+/*
+ * K+P iMX6Q KP_IMX6Q_TPC board configuration
+ *
+ * Copyright (C) 2018 Lukasz Majewski <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <errno.h>
+#include <fsl_esdhc.h>
+#include <fuse.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <mmc.h>
+#include <net.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define

ENET_PAD_CTRL
\

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |

PAD_CTL_DSE_40ohm | \

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +3 -0
+	 PAD_CTL_HYS)
+
+#define

I2C_PAD_CTRL
\

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |

PAD_CTL_DSE_40ohm | \

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +48 -0
+	PAD_CTL_HYS | PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define PC			MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+static struct i2c_pads_info kp_imx6q_tpc_i2c_pad_info0 = {
+	.scl = {
+		.i2c_mode  = MX6Q_PAD_CSI0_DAT9__I2C1_SCL | PC,
+		.gpio_mode = MX6Q_PAD_CSI0_DAT9__GPIO5_IO27 | PC,
+		.gp = IMX_GPIO_NR(5, 27)
+	},
+	.sda = {
+		 .i2c_mode = MX6Q_PAD_CSI0_DAT8__I2C1_SDA | PC,
+		 .gpio_mode = MX6Q_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
+		 .gp = IMX_GPIO_NR(5, 26)
+	}
+};
+
+static struct i2c_pads_info kp_imx6q_tpc_i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode  = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC,
+		.gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | PC,
+		.gp = IMX_GPIO_NR(4, 12)
+	},
+	.sda = {
+		 .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC,
+		 .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC,
+		 .gp = IMX_GPIO_NR(4, 13)
+	}
+};
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+	return 0;
+}
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const enet_pads[] = {
+	IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_ENET_MDC__ENET_MDC	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +3 -0
+	IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL |
+		   MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK |

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3	|

MUX_PAD_CTRL(ENET_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +4 -0
+	IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL |
+		   MUX_PAD_CTRL(ENET_PAD_CTRL)),
+	/* AR8031 PHY Reset */
+	IOMUX_PADS(PAD_ENET_CRS_DV__GPIO1_IO25	|

MUX_PAD_CTRL(NO_PAD_CTRL)), +};

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +13 -0
+
+static void eth_phy_reset(void)
+{
+	/* Reset AR8031 PHY */
+	gpio_direction_output(IMX_GPIO_NR(1, 25), 0);
+	mdelay(10);
+	gpio_set_value(IMX_GPIO_NR(1, 25), 1);
+	udelay(100);
+}
+
+static int setup_fec_clock(void)
+{
+	struct iomuxc *iomuxc_regs = (struct iomuxc

*)IOMUXC_BASE_ADDR; +

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +2 -0
+	/* set gpr1[21] to select anatop clock */
+	clrsetbits_le32(&iomuxc_regs->gpr[1], 0x1 << 21, 0x1 <<

21); +

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +57 -0
+	return enable_fec_anatop_clock(0, ENET_50MHZ);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	SETUP_IOMUX_PADS(enet_pads);
+	setup_fec_clock();
+	eth_phy_reset();
+
+	return cpu_eth_init(bis);
+}
+
+static int ar8031_phy_fixup(struct phy_device *phydev)
+{
+	unsigned short val;
+
+	/* To enable AR8031 output a 125MHz clk from CLK_25M */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+	val &= 0xffe3;
+	val |= 0x18;
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+	/* introduce tx clock delay */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+	val |= 0x0100;
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	ar8031_phy_fixup(phydev);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FSL_ESDHC
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{ USDHC2_BASE_ADDR },
+	{ USDHC4_BASE_ADDR },
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg

*)mmc->priv; +

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +16 -0
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		return !gpio_get_value(USDHC2_CD_GPIO);
+	case USDHC4_BASE_ADDR:
+		return 1; /* eMMC/uSDHC4 is always present */
+	}
+
+	return 0;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+
+	/*
+	 * According to the board_mmc_init() the following map is

done:

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +47 -0
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0                    micro SD
+	 * mmc2                    eMMC
+	 */
+	gpio_direction_input(USDHC2_CD_GPIO);
+
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_USB_EHCI_MX6
+static void setup_usb(void)
+{
+	/*
+	 * Set daisy chain for otg_pin_id on MX6Q.
+	 * For MX6DL, this bit is reserved.
+	 */
+	imx_iomux_set_gpr_register(1, 13, 1, 0);
+}
+
+int board_usb_phy_mode(int port)
+{
+	if (port == 1)
+		return USB_INIT_HOST;
+	else
+		return USB_INIT_DEVICE;
+}
+
+int board_ehci_power(int port, int on)
+{
+	switch (port) {
+	case 0:
+		break;
+	case 1:
+		gpio_direction_output(IMX_GPIO_NR(3, 31), !!on);
+		break;
+	default:
+		printf("MXC USB port %d not yet supported\n",

port);

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +19 -0
+		return -EINVAL;
+	}
+
+	return 0;
+}
+#endif
+
+int board_early_init_f(void)
+{
+#ifdef CONFIG_USB_EHCI_MX6
+	setup_usb();
+#endif
+
+	return 0;
+}
+
+int board_init(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg

*)CCM_BASE_ADDR; +

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +5 -0
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	/* Enable eim_slow clocks */
+	setbits_le32(&mxc_ccm->CCGR6, 0x1 <<

MXC_CCM_CCGR6_EMI_SLOW_OFFSET); +

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f,

&kp_imx6q_tpc_i2c_pad_info0);

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +1 -0
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f,

&kp_imx6q_tpc_i2c_pad_info1); +

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc.c new file +29 -0
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd2",  MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+	/* 8 bit bus width */
+	{"emmc", MAKE_CFGVAL(0x60, 0x58, 0x00, 0x00)},
+	{NULL,	 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+	env_set("boardname", "kp-tpc");
+	env_set("boardsoc", "imx6q");
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: K+P KP_IMX6Q_TPC i.MX6Q\n");
+	return 0;
+}
(quoted diff) +0 -0

b/board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file mode 100644 index 0000000000..b5723b41c1

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +29 -0
@@ -0,0 +1,283 @@
+/*
+ * K+P iMX6Q KP_IMX6Q_TPC board configuration
+ *
+ * Copyright (C) 2018 Lukasz Majewski <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <fuse.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <spl.h>
+
+#define

UART_PAD_CTRL
\

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |

PAD_CTL_DSE_40ohm | \

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +3 -0
+	 PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define

USDHC_PAD_CTRL
\

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	(PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW |

PAD_CTL_DSE_80ohm | \

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +7 -0
+	 PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg

*)CCM_BASE_ADDR; +

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +12 -0
+	writel(0x00C03F3F, &ccm->CCGR0);
+	writel(0x0030FC03, &ccm->CCGR1);
+	writel(0x0FFFC000, &ccm->CCGR2);
+	writel(0x3FF00000, &ccm->CCGR3);
+	writel(0x00FFF300, &ccm->CCGR4);
+	writel(0x0F0000C3, &ccm->CCGR5);
+	writel(0x000003FF, &ccm->CCGR6);
+}
+
+/* onboard microSD */
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD2_CLK__SD2_CLK	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD2_CMD__SD2_CMD	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_NANDF_CS3__GPIO6_IO16	|

MUX_PAD_CTRL(NO_PAD_CTRL)), +};

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +4 -0
+
+/* eMMC */
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+	IOMUX_PADS(PAD_SD4_DAT0__SD4_DATA0	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD4_DAT1__SD4_DATA1	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD4_DAT2__SD4_DATA2	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD4_DAT3__SD4_DATA3	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD4_DAT4__SD4_DATA4	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD4_DAT5__SD4_DATA5	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD4_DAT6__SD4_DATA6	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD4_DAT7__SD4_DATA7	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD4_CLK__SD4_CLK	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD4_CMD__SD4_CMD	|

MUX_PAD_CTRL(USDHC_PAD_CTRL)), +};

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +11 -0
+
+/* SD */
+static void setup_iomux_sd(void)
+{
+	SETUP_IOMUX_PADS(usdhc2_pads);
+	SETUP_IOMUX_PADS(usdhc4_pads);
+}
+
+/* UART */
+static iomux_v3_cfg_t const uart1_pads[] = {
+	IOMUX_PADS(PAD_SD3_DAT7__UART1_TX_DATA	|

MUX_PAD_CTRL(UART_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_SD3_DAT6__UART1_RX_DATA	|

MUX_PAD_CTRL(UART_PAD_CTRL)), +};

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +9 -0
+
+static void setup_iomux_uart(void)
+{
+	SETUP_IOMUX_PADS(uart1_pads);
+}
+
+/* USB */
+static iomux_v3_cfg_t const usb_pads[] = {
+	IOMUX_PADS(PAD_GPIO_1__USB_OTG_ID	|

MUX_PAD_CTRL(NO_PAD_CTRL)),

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31	|

MUX_PAD_CTRL(NO_PAD_CTRL)), +};

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +3 -0
+
+static void setup_iomux_usb(void)
+{

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c line 112

Quoted 10 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +10 -0
+	SETUP_IOMUX_PADS(usb_pads);
+}
+
+/*
+ * This code has been extracted from mx6q_8x_mt41K256.cfg DCD
+ * NXP's BSP u-boot mx6q_8x_mt41K256.cfg rel_imx_4.1.15_2.1.0_ga
+ */
+static int mx6q_dcd_table[] = {
+	0x020e0798, 0x000C0000,
+	0x020e0758, 0x00000000,  

Well.....

Quoted 3 lines

This is a Quad, well supported, we have a nice framework to setup the DDR. I do not like to see this dump of table in code. Which is the added value compared to the DCD table using the i.MX header ?

If I may explain, why I decided to use DCD table from the outset :-).

1. This board is based on sabresd port. It uses the same approach as presented here:

board/freescale/mxsabresd/mxsabresd.c [1]

2. This board's old BSP uses identical DCD code - in that way I do avoid problems with DDR3 debugging and instability issues.

Quoted 57 lines

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c line 122

Quoted 11 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +10 -0
+	0x020e0588, 0x00000030,
+	0x020e0594, 0x00000030,
+	0x020e056c, 0x00000030,
+	0x020e0578, 0x00000030,
+	0x020e074c, 0x00000030,
+	0x020e057c, 0x00000030,
+	0x020e058c, 0x00000000,
+	0x020e059c, 0x00000030,
+	0x020e05a0, 0x00000030,
+	0x020e078c, 0x00000030,  

There are structure and function to set these.

Quoted 43 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +43 -0
+	0x020e0750, 0x00020000,
+	0x020e05a8, 0x00000018,
+	0x020e05b0, 0x00000018,
+	0x020e0524, 0x00000018,
+	0x020e051c, 0x00000018,
+	0x020e0518, 0x00000018,
+	0x020e050c, 0x00000018,
+	0x020e05b8, 0x00000018,
+	0x020e05c0, 0x00000018,
+	0x020e0774, 0x00020000,
+	0x020e0784, 0x00000018,
+	0x020e0788, 0x00000018,
+	0x020e0794, 0x00000018,
+	0x020e079c, 0x00000018,
+	0x020e07a0, 0x00000018,
+	0x020e07a4, 0x00000018,
+	0x020e07a8, 0x00000018,
+	0x020e0748, 0x00000018,
+	0x020e05ac, 0x00000018,
+	0x020e05b4, 0x00000018,
+	0x020e0528, 0x00000018,
+	0x020e0520, 0x00000018,
+	0x020e0514, 0x00000018,
+	0x020e0510, 0x00000018,
+	0x020e05bc, 0x00000018,
+	0x020e05c4, 0x00000018,
+	0x021b0800, 0xa1390003,
+	0x021b080c, 0x001F001F,
+	0x021b0810, 0x001F001F,
+	0x021b480c, 0x001F001F,
+	0x021b4810, 0x001F001F,
+	0x021b083c, 0x43270338,
+	0x021b0840, 0x03200314,
+	0x021b483c, 0x431A032F,
+	0x021b4840, 0x03200263,
+	0x021b0848, 0x4B434748,
+	0x021b4848, 0x4445404C,
+	0x021b0850, 0x38444542,
+	0x021b4850, 0x4935493A,
+	0x021b081c, 0x33333333,
+	0x021b0820, 0x33333333,
+	0x021b0824, 0x33333333,
+	0x021b0828, 0x33333333,
Quoted 8 lines

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c line 169

Quoted 4 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +4 -0
+	0x021b481c, 0x33333333,
+	0x021b4820, 0x33333333,
+	0x021b4824, 0x33333333,
+	0x021b4828, 0x33333333,  

Like calibration and so on. Please change this as done by other board, using structures ( mx6_ddr3_cfg, mx6dq_iomux_grp_regs) and calling mx6dq_dram_iocfg() and mx6_dram_cfg() - thanks !

Yes. I do know that API.

In v2. I will try to convert this board to use it.

Quoted 27 lines
Quoted 27 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +26 -0
+	0x021b08b8, 0x00000800,
+	0x021b48b8, 0x00000800,
+	0x021b0004, 0x00020036,
+	0x021b0008, 0x09444040,
+	0x021b000c, 0x8A8F7955,
+	0x021b0010, 0xFF328F64,
+	0x021b0014, 0x01FF00DB,
+	0x021b0018, 0x00001740,
+	0x021b001c, 0x00008000,
+	0x021b002c, 0x000026d2,
+	0x021b0030, 0x008F1023,
+	0x021b0040, 0x00000047,
+	0x021b0000, 0x841A0000,
+	0x021b001c, 0x04088032,
+	0x021b001c, 0x00008033,
+	0x021b001c, 0x00048031,
+	0x021b001c, 0x09408030,
+	0x021b001c, 0x04008040,
+	0x021b0020, 0x00005800,
+	0x021b0818, 0x00011117,
+	0x021b4818, 0x00011117,
+	0x021b0004, 0x00025576,
+	0x021b0404, 0x00011006,
+	0x021b001c, 0x00000000,
+};
+
Quoted 8 lines

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c line 201

Quoted 6 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +6 -0
+static void ddr_init(int *table, int size)
+{
+	int i;
+
+	for (i = 0; i < size / 2 ; i++)
+		writel(table[2 * i + 1], table[2 * i]);  

Quite nasty....

As in [1]...

Quoted 267 lines
Quoted 267 lines
board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +11 -0
+}
+
+struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{USDHC2_BASE_ADDR},
+	{USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg

*)mmc->priv;

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +20 -0
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	case USDHC4_BASE_ADDR:
+		ret = 1; /* eMMC/uSDHC4 is always present */
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bd)
+{
+	struct src *psrc = (struct src *)SRC_BASE_ADDR;
+	unsigned int reg = readl(&psrc->sbmr1) >> 11;
+	/*
+	 * Upon reading BOOT_CFG register the following map is

done:

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +1 -0
+	 * Bit 11 and 12 of BOOT_CFG register can determine the

current

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +10 -0
+	 * mmc port
+	 * 0x1                  SD1
+	 * 0x3                  SD4
+	 */
+
+	switch (reg & 0x3) {
+	case 0x1:
+		SETUP_IOMUX_PADS(usdhc2_pads);
+		usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk =

mxc_get_clock(MXC_ESDHC2_CLK);

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +6 -0
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	case 0x3:
+		SETUP_IOMUX_PADS(usdhc4_pads);
+		usdhc_cfg[0].esdhc_base = USDHC4_BASE_ADDR;
+		usdhc_cfg[0].sdhc_clk =

mxc_get_clock(MXC_ESDHC4_CLK);

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +26 -0
+		gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
+		break;
+	}
+
+	return fsl_esdhc_initialize(bd, &usdhc_cfg[0]);
+}
+
+void board_init_f(ulong dummy)
+{
+	/* Setup DDR3 from NXP's BSP DCD file */
+	ddr_init(mx6q_dcd_table, ARRAY_SIZE(mx6q_dcd_table));
+
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+	gpr_init();
+
+	/* setup GP timer */
+	timer_init();
+
+	setup_iomux_sd();
+	setup_iomux_uart();
+	setup_iomux_usb();
+
+	/* UART clocks enabled and gd valid - init serial console

*/

board/k+p/kp_imx6q_tpc/kp_imx6q_tpc_spl.c new file +8 -0
+	preloader_console_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
(quoted diff) +0 -0

b/configs/kp_imx6q_tpc_defconfig new file mode 100644 index 0000000000..d2c6e2e6ba

configs/kp_imx6q_tpc_defconfig new file +42 -0
@@ -0,0 +1,42 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x17800000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_MX6_DDRCAL=y
+CONFIG_TARGET_KP_IMX6Q_TPC=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_WATCHDOG_SUPPORT=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
+# CONFIG_USE_BOOTCOMMAND is not set
+CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE=y
+CONFIG_SPL=y
+CONFIG_SPL_RAW_IMAGE_SUPPORT=y
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_STOP_STR="."
+# CONFIG_CMD_BOOTEFI_HELLO_COMPILE is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_EXT4_WRITE=y
+# CONFIG_ISO_PARTITION is not set
+# CONFIG_EFI_PARTITION is not set
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ATHEROS=y
+CONFIG_NETDEVICES=y
+CONFIG_FEC_MXC=y
+CONFIG_IMX_THERMAL=y
+CONFIG_USB=y
+CONFIG_USB_STORAGE=y
+CONFIG_OF_LIBFDT=y
(quoted diff) +0 -0

b/include/configs/kp_imx6q_tpc.h new file mode 100644 index 0000000000..74143a2dba

include/configs/kp_imx6q_tpc.h new file +17 -0
@@ -0,0 +1,128 @@
+/*
+ * K+P iMX6Q KP_IMX6Q_TPC board configuration
+ *
+ * Copyright (C) 2018 Lukasz Majewski <[email protected]>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __KP_IMX6Q_TPC_IMX6_CONFIG_H_
+#define __KP_IMX6Q_TPC_IMX6_CONFIG_H_
+
+#include <asm/arch/imx-regs.h>
+
+#include "mx6_common.h"
+
+/* SPL */
+#include "imx6_spl.h"			/* common IMX6 SPL

configuration */ +

include/configs/kp_imx6q_tpc.h new file +28 -0
+/* Miscellaneous configurable options */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
+
+#define CONFIG_BOUNCE_BUFFER
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(4 * SZ_1M)
+
+/* FEC ethernet */
+#define CONFIG_MII
+#define IMX_FEC_BASE			ENET_BASE_ADDR
+#define CONFIG_FEC_XCV_TYPE		RGMII
+#define CONFIG_ETHPRIME			"FEC"
+#define CONFIG_FEC_MXC_PHYADDR		0
+#define CONFIG_ARP_TIMEOUT		200UL
+
+/* Fuses */
+#ifdef CONFIG_CMD_FUSE
+#define CONFIG_MXC_OCOTP
+#endif
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1

*/ +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C
bus 2 */ +#define CONFIG_SYS_I2C_SPEED 100000

include/configs/kp_imx6q_tpc.h new file +7 -0
+
+/* MMC Configs */
+#define CONFIG_FSL_ESDHC
+#define CONFIG_FSL_USDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	0
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+#define CONFIG_SYS_MMC_ENV_DEV		1 /* 0 = SDHC2, 1 =

SDHC4 (eMMC) */ +

include/configs/kp_imx6q_tpc.h new file +12 -0
+/* UART */
+#define CONFIG_MXC_UART
+#define CONFIG_MXC_UART_BASE		UART1_BASE
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+
+/* USB Configs */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI |

PORT_PTS_PTW) +#define CONFIG_MXC_USB_FLAGS 0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 /* Enabled USB
controller number */ +#endif

include/configs/kp_imx6q_tpc.h new file +53 -0
+
+/* Watchdog */
+#define CONFIG_HW_WATCHDOG
+#define CONFIG_IMX_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT_MSECS	60000
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_LOADADDR			0x12000000
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS	\
+	"console=ttymxc0,115200\0"	\
+	"fdt_addr=0x18000000\0"		\
+	"fdt_high=0xffffffff\0"		\
+	"initrd_high=0xffffffff\0"	\
+	"kernel_addr_r=0x10008000\0"	\
+	"fdt_addr_r=0x13000000\0"	\
+	"ramdisk_addr_r=0x18000000\0"	\
+	"scriptaddr=0x14000000\0"	\
+	"kernel_file=fitImage\0"\
+	BOOTENV
+
+#define CONFIG_BOOTCOMMAND		"run distro_bootcmd"
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 0) \
+	func(MMC, mmc, 1) \
+	func(USB, usb, 0) \
+	func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+#endif
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
+
+/* Environment */
+#define CONFIG_ENV_SIZE	(SZ_8K)
+#define CONFIG_ENV_OFFSET       0x100000
Quoted 9 lines

include/configs/kp_imx6q_tpc.h line 128

Quoted 5 lines

+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT

include/configs/kp_imx6q_tpc.h new file +2 -0
+
+#endif	/* __KP_IMX6Q_TPC_IMX6_CONFIG_H_ */

Best regards,
Stefano Babic

Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de -------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20180329/ad970c84/attachment.sig>