Skip to contentSkip to conversation

i40e: move I40E_FLAG_FILTER_SYNC to a state bit

PATCH New Alice Michael 2 participants 16 messages Mar 16, 2018 – Mar 19, 2018

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/8 i40e: move I40E_FLAG_FILTER_SYNC to a state bit

From: Jacob Keller <[email protected]>

The I40E_FLAG_FILTER_SYNC flag is modified during run time possibly when the RTNL lock is not held. Thus, it should not be part of pf->flags, and instead should be using atomic bit operations in the pf->state field.

Create a __I40E_MACVLAN_SYNC_PENDING state bit, and use it instead of the old I40E_FLAG_FILTER_SYNC flag.

This is part of a larger effort to remove the need for cmpxchg64 in i40e_set_priv_flags().

---
 drivers/net/ethernet/intel/i40e/i40e.h      |  3 ++-
 drivers/net/ethernet/intel/i40e/i40e_main.c | 16 +++++++++-------
 2 files changed, 11 insertions(+), 8 deletions(-)
drivers/net/ethernet/intel/i40e/i40e.h +2 -1
index 1e1cd52..e83fb37 100644
@@ -162,6 +162,7 @@ enum i40e_state_t {
 	__I40E_RESET_FAILED,
 	__I40E_PORT_SUSPENDED,
 	__I40E_VF_DISABLE,
+	__I40E_MACVLAN_SYNC_PENDING,
 	/* This must be last as it determines the size of the BITMAP */
 	__I40E_STATE_SIZE__,
 };
@@ -516,7 +517,7 @@ struct i40e_pf {
 #define I40E_FLAG_MSIX_ENABLED			BIT_ULL(2)
 #define I40E_FLAG_RSS_ENABLED			BIT_ULL(3)
 #define I40E_FLAG_VMDQ_ENABLED			BIT_ULL(4)
-#define I40E_FLAG_FILTER_SYNC			BIT_ULL(5)
+/* Gap for BIT_ULL(5) */
 #define I40E_FLAG_SRIOV_ENABLED			BIT_ULL(6)
 #define I40E_FLAG_DCB_CAPABLE			BIT_ULL(7)
 #define I40E_FLAG_DCB_ENABLED			BIT_ULL(8)
drivers/net/ethernet/intel/i40e/i40e_main.c +9 -7
index 5a77dbf..e96c22a 100644
@@ -1382,7 +1382,7 @@ struct i40e_mac_filter *i40e_add_filter(struct i40e_vsi *vsi,
 		hash_add(vsi->mac_filter_hash, &f->hlist, key);
 
 		vsi->flags |= I40E_VSI_FLAG_FILTER_CHANGED;
-		vsi->back->flags |= I40E_FLAG_FILTER_SYNC;
+		set_bit(__I40E_MACVLAN_SYNC_PENDING, vsi->back->state);
 	}
 
 	/* If we're asked to add a filter that has been marked for removal, it
@@ -1432,7 +1432,7 @@ void __i40e_del_filter(struct i40e_vsi *vsi, struct i40e_mac_filter *f)
 	}
 
 	vsi->flags |= I40E_VSI_FLAG_FILTER_CHANGED;
-	vsi->back->flags |= I40E_FLAG_FILTER_SYNC;
+	set_bit(__I40E_MACVLAN_SYNC_PENDING, vsi->state);
 }
 
 /**
@@ -1955,7 +1955,7 @@ static void i40e_set_rx_mode(struct net_device *netdev)
 	/* check for other flag changes */
 	if (vsi->current_netdev_flags != vsi->netdev->flags) {
 		vsi->flags |= I40E_VSI_FLAG_FILTER_CHANGED;
-		vsi->back->flags |= I40E_FLAG_FILTER_SYNC;
+		set_bit(__I40E_MACVLAN_SYNC_PENDING, vsi->back->state);
 	}
 }
 
@@ -2577,9 +2577,10 @@ static void i40e_sync_filters_subtask(struct i40e_pf *pf)
 {
 	int v;
 
-	if (!pf || !(pf->flags & I40E_FLAG_FILTER_SYNC))
+	if (!pf)
+		return;
+	if (!test_and_clear_bit(__I40E_MACVLAN_SYNC_PENDING, pf->state))
 		return;
-	pf->flags &= ~I40E_FLAG_FILTER_SYNC;
 
 	for (v = 0; v < pf->num_alloc_vsi; v++) {
 		if (pf->vsi[v] &&
@@ -2588,7 +2589,8 @@ static void i40e_sync_filters_subtask(struct i40e_pf *pf)
 
 			if (ret) {
 				/* come back and try again later */
-				pf->flags |= I40E_FLAG_FILTER_SYNC;
+				set_bit(__I40E_MACVLAN_SYNC_PENDING,
+					pf->state);
 				break;
 			}
 		}
@@ -12240,7 +12242,7 @@ static int i40e_add_vsi(struct i40e_vsi *vsi)
 
 	if (f_count) {
 		vsi->flags |= I40E_VSI_FLAG_FILTER_CHANGED;
-		pf->flags |= I40E_FLAG_FILTER_SYNC;
+		set_bit(__I40E_MACVLAN_SYNC_PENDING, pf->state);
 	}
 
 	/* Update VSI BW information */
Signature · 1 line
2.9.5
#1 lore raw

PATCH 2/8 i40e: move I40E_FLAG_UDP_FILTER_SYNC to the state field

From: Jacob Keller <[email protected]>

This flag is modified during run time, possibly even when the RTNL lock is not held. Additionally it has a few places which should be using test_and_set or test_and_clear atomic bit operations.

Create a new state bit __I40E_UDP_SYNC_PENDING and use it instead of the ole I40E_FLAG_UDP_FILTER_SYNC flag.

This is part of a larger effort to remove the need for using cmpxchg64 in i40e_set_priv_flags.

---
 drivers/net/ethernet/intel/i40e/i40e.h      |  3 ++-
 drivers/net/ethernet/intel/i40e/i40e_main.c | 10 ++++------
 2 files changed, 6 insertions(+), 7 deletions(-)
drivers/net/ethernet/intel/i40e/i40e.h +2 -1
index e83fb37..ff309501 100644
@@ -163,6 +163,7 @@ enum i40e_state_t {
 	__I40E_PORT_SUSPENDED,
 	__I40E_VF_DISABLE,
 	__I40E_MACVLAN_SYNC_PENDING,
+	__I40E_UDP_FILTER_SYNC_PENDING,
 	/* This must be last as it determines the size of the BITMAP */
 	__I40E_STATE_SIZE__,
 };
@@ -526,7 +527,7 @@ struct i40e_pf {
 #define I40E_FLAG_FD_SB_AUTO_DISABLED		BIT_ULL(11)
 #define I40E_FLAG_FD_ATR_AUTO_DISABLED		BIT_ULL(12)
 #define I40E_FLAG_MFP_ENABLED			BIT_ULL(13)
-#define I40E_FLAG_UDP_FILTER_SYNC		BIT_ULL(14)
+/* Gap for BIT_ULL(14) */
 #define I40E_FLAG_HW_ATR_EVICT_ENABLED		BIT_ULL(15)
 #define I40E_FLAG_VEB_MODE_ENABLED		BIT_ULL(16)
 #define I40E_FLAG_VEB_STATS_ENABLED		BIT_ULL(17)
drivers/net/ethernet/intel/i40e/i40e_main.c +4 -6
index e96c22a..a24f99a 100644
@@ -9721,7 +9721,7 @@ static void i40e_sync_udp_filters(struct i40e_pf *pf)
 			pf->pending_udp_bitmap |= BIT_ULL(i);
 	}
 
-	pf->flags |= I40E_FLAG_UDP_FILTER_SYNC;
+	set_bit(__I40E_UDP_FILTER_SYNC_PENDING, pf->state);
 }
 
 /**
@@ -9735,11 +9735,9 @@ static void i40e_sync_udp_filters_subtask(struct i40e_pf *pf)
 	u16 port;
 	int i;
 
-	if (!(pf->flags & I40E_FLAG_UDP_FILTER_SYNC))
+	if (!test_and_clear_bit(__I40E_UDP_FILTER_SYNC_PENDING, pf->state))
 		return;
 
-	pf->flags &= ~I40E_FLAG_UDP_FILTER_SYNC;
-
 	for (i = 0; i < I40E_MAX_PF_UDP_OFFLOAD_PORTS; i++) {
 		if (pf->pending_udp_bitmap & BIT_ULL(i)) {
 			pf->pending_udp_bitmap &= ~BIT_ULL(i);
@@ -11439,7 +11437,7 @@ static void i40e_udp_tunnel_add(struct net_device *netdev,
 	/* New port: add it and mark its index in the bitmap */
 	pf->udp_ports[next_idx].port = port;
 	pf->pending_udp_bitmap |= BIT_ULL(next_idx);
-	pf->flags |= I40E_FLAG_UDP_FILTER_SYNC;
+	set_bit(__I40E_UDP_FILTER_SYNC_PENDING, pf->state);
 }
 
 /**
@@ -11480,7 +11478,7 @@ static void i40e_udp_tunnel_del(struct net_device *netdev,
 	 */
 	pf->udp_ports[idx].port = 0;
 	pf->pending_udp_bitmap |= BIT_ULL(idx);
-	pf->flags |= I40E_FLAG_UDP_FILTER_SYNC;
+	set_bit(__I40E_UDP_FILTER_SYNC_PENDING, pf->state);
 
 	return;
 not_found:
Signature · 1 line
2.9.5
#2 lore raw

PATCH 2/8 i40e: move I40E_FLAG_UDP_FILTER_SYNC to the state field

Quoted 18 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On Behalf Of Alice Michael
Sent: Friday, March 16, 2018 1:27 AM
To: Michael, Alice <[email protected]>; intel-wired- lan at lists.osuosl.org
Subject: [Intel-wired-lan] [next PATCH S89 2/8] i40e: move I40E_FLAG_UDP_FILTER_SYNC to the state field

From: Jacob Keller <[email protected]>

This flag is modified during run time, possibly even when the RTNL lock is not held. Additionally it has a few places which should be using test_and_set or test_and_clear atomic bit operations.

Create a new state bit __I40E_UDP_SYNC_PENDING and use it instead of the ole I40E_FLAG_UDP_FILTER_SYNC flag.

Quoted 8 lines

This is part of a larger effort to remove the need for using cmpxchg64 in i40e_set_priv_flags.

---
 drivers/net/ethernet/intel/i40e/i40e.h      |  3 ++-
 drivers/net/ethernet/intel/i40e/i40e_main.c | 10 ++++------
 2 files changed, 6 insertions(+), 7 deletions(-)
#3 lore raw

PATCH 3/8 i40e: move AUTO_DISABLED flags into the state field

In reply to Alice Michael

From: Jacob Keller <[email protected]>

The two Flow Directory auto disable flags are used at run time to mark when the flow director features needed to be disabled. Thus the flags could change even when the RTNL lock is not held.

They also have some code constructions which really should be test_and_set or test_and_clear using atomic bit operations.

Create new state fields to mark this, and stop including them in pf->flags.

This is part of a larger effort to remove the need for cmpxchg64 in i40e_set_priv_flags().

---
 drivers/net/ethernet/intel/i40e/i40e.h         |  5 +++--
 drivers/net/ethernet/intel/i40e/i40e_ethtool.c |  4 ++--
 drivers/net/ethernet/intel/i40e/i40e_main.c    | 23 +++++++++--------------
 drivers/net/ethernet/intel/i40e/i40e_txrx.c    | 21 +++++++++++++--------
 4 files changed, 27 insertions(+), 26 deletions(-)
drivers/net/ethernet/intel/i40e/i40e.h +3 -2
index ff309501..c41d99b 100644
@@ -159,6 +159,8 @@ enum i40e_state_t {
 	__I40E_BAD_EEPROM,
 	__I40E_DOWN_REQUESTED,
 	__I40E_FD_FLUSH_REQUESTED,
+	__I40E_FD_ATR_AUTO_DISABLED,
+	__I40E_FD_SB_AUTO_DISABLED,
 	__I40E_RESET_FAILED,
 	__I40E_PORT_SUSPENDED,
 	__I40E_VF_DISABLE,
@@ -524,8 +526,7 @@ struct i40e_pf {
 #define I40E_FLAG_DCB_ENABLED			BIT_ULL(8)
 #define I40E_FLAG_FD_SB_ENABLED			BIT_ULL(9)
 #define I40E_FLAG_FD_ATR_ENABLED		BIT_ULL(10)
-#define I40E_FLAG_FD_SB_AUTO_DISABLED		BIT_ULL(11)
-#define I40E_FLAG_FD_ATR_AUTO_DISABLED		BIT_ULL(12)
+/* Gap for BIT_ULL(11) and BIT_ULL(12) */
 #define I40E_FLAG_MFP_ENABLED			BIT_ULL(13)
 /* Gap for BIT_ULL(14) */
 #define I40E_FLAG_HW_ATR_EVICT_ENABLED		BIT_ULL(15)
drivers/net/ethernet/intel/i40e/i40e_ethtool.c +2 -2
index 722eb6b..031bc7c 100644
@@ -3951,7 +3951,7 @@ static int i40e_add_fdir_ethtool(struct i40e_vsi *vsi,
 	if (!(pf->flags & I40E_FLAG_FD_SB_ENABLED))
 		return -EOPNOTSUPP;
 
-	if (pf->flags & I40E_FLAG_FD_SB_AUTO_DISABLED)
+	if (test_bit(__I40E_FD_SB_AUTO_DISABLED, pf->state))
 		return -ENOSPC;
 
 	if (test_bit(__I40E_RESET_RECOVERY_PENDING, pf->state) ||
@@ -4460,7 +4460,7 @@ static int i40e_set_priv_flags(struct net_device *dev, u32 flags)
 	/* Flush current ATR settings if ATR was disabled */
 	if ((changed_flags & I40E_FLAG_FD_ATR_ENABLED) &&
 	    !(pf->flags & I40E_FLAG_FD_ATR_ENABLED)) {
-		pf->flags |= I40E_FLAG_FD_ATR_AUTO_DISABLED;
+		set_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state);
 		set_bit(__I40E_FD_FLUSH_REQUESTED, pf->state);
 	}
 
drivers/net/ethernet/intel/i40e/i40e_main.c +9 -14
index a24f99a..44d15cf 100644
@@ -1083,13 +1083,13 @@ static void i40e_update_pf_stats(struct i40e_pf *pf)
 			   &osd->rx_lpi_count, &nsd->rx_lpi_count);
 
 	if (pf->flags & I40E_FLAG_FD_SB_ENABLED &&
-	    !(pf->flags & I40E_FLAG_FD_SB_AUTO_DISABLED))
+	    !test_bit(__I40E_FD_SB_AUTO_DISABLED, pf->state))
 		nsd->fd_sb_status = true;
 	else
 		nsd->fd_sb_status = false;
 
 	if (pf->flags & I40E_FLAG_FD_ATR_ENABLED &&
-	    !(pf->flags & I40E_FLAG_FD_ATR_AUTO_DISABLED))
+	    !test_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state))
 		nsd->fd_atr_status = true;
 	else
 		nsd->fd_atr_status = false;
@@ -8144,12 +8144,10 @@ u32 i40e_get_global_fd_count(struct i40e_pf *pf)
  **/
 static void i40e_reenable_fdir_sb(struct i40e_pf *pf)
 {
-	if (pf->flags & I40E_FLAG_FD_SB_AUTO_DISABLED) {
-		pf->flags &= ~I40E_FLAG_FD_SB_AUTO_DISABLED;
+	if (test_and_clear_bit(__I40E_FD_SB_AUTO_DISABLED, pf->state))
 		if ((pf->flags & I40E_FLAG_FD_SB_ENABLED) &&
 		    (I40E_DEBUG_FD & pf->hw.debug_mask))
 			dev_info(&pf->pdev->dev, "FD Sideband/ntuple is being enabled since we have space in the table now\n");
-	}
 }
 
 /**
@@ -8158,7 +8156,7 @@ static void i40e_reenable_fdir_sb(struct i40e_pf *pf)
  **/
 static void i40e_reenable_fdir_atr(struct i40e_pf *pf)
 {
-	if (pf->flags & I40E_FLAG_FD_ATR_AUTO_DISABLED) {
+	if (test_and_clear_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state)) {
 		/* ATR uses the same filtering logic as SB rules. It only
 		 * functions properly if the input set mask is at the default
 		 * settings. It is safe to restore the default input set
@@ -8168,7 +8166,6 @@ static void i40e_reenable_fdir_atr(struct i40e_pf *pf)
 					I40E_L3_SRC_MASK | I40E_L3_DST_MASK |
 					I40E_L4_SRC_MASK | I40E_L4_DST_MASK);
 
-		pf->flags &= ~I40E_FLAG_FD_ATR_AUTO_DISABLED;
 		if ((pf->flags & I40E_FLAG_FD_ATR_ENABLED) &&
 		    (I40E_DEBUG_FD & pf->hw.debug_mask))
 			dev_info(&pf->pdev->dev, "ATR is being enabled since we have space in the table and there are no conflicting ntuple rules\n");
@@ -8291,7 +8288,7 @@ static void i40e_fdir_flush_and_replay(struct i40e_pf *pf)
 	}
 
 	pf->fd_flush_timestamp = jiffies;
-	pf->flags |= I40E_FLAG_FD_ATR_AUTO_DISABLED;
+	set_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state);
 	/* flush all filters */
 	wr32(&pf->hw, I40E_PFQF_CTL_1,
 	     I40E_PFQF_CTL_1_CLEARFDTABLE_MASK);
@@ -8311,7 +8308,7 @@ static void i40e_fdir_flush_and_replay(struct i40e_pf *pf)
 		/* replay sideband filters */
 		i40e_fdir_filter_restore(pf->vsi[pf->lan_vsi]);
 		if (!disable_atr && !pf->fd_tcp4_filter_cnt)
-			pf->flags &= ~I40E_FLAG_FD_ATR_AUTO_DISABLED;
+			clear_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state);
 		clear_bit(__I40E_FD_FLUSH_REQUESTED, pf->state);
 		if (I40E_DEBUG_FD & pf->hw.debug_mask)
 			dev_info(&pf->pdev->dev, "FD Filter table flushed and FD-SB replayed.\n");
@@ -11291,20 +11288,18 @@ bool i40e_set_ntuple(struct i40e_pf *pf, netdev_features_t features)
 			need_reset = true;
 			i40e_fdir_filter_exit(pf);
 		}
-		pf->flags &= ~(I40E_FLAG_FD_SB_ENABLED |
-			       I40E_FLAG_FD_SB_AUTO_DISABLED);
+		pf->flags &= ~I40E_FLAG_FD_SB_ENABLED;
+		clear_bit(__I40E_FD_SB_AUTO_DISABLED, pf->state);
 		pf->flags |= I40E_FLAG_FD_SB_INACTIVE;
 
 		/* reset fd counters */
 		pf->fd_add_err = 0;
 		pf->fd_atr_cnt = 0;
 		/* if ATR was auto disabled it can be re-enabled. */
-		if (pf->flags & I40E_FLAG_FD_ATR_AUTO_DISABLED) {
-			pf->flags &= ~I40E_FLAG_FD_ATR_AUTO_DISABLED;
+		if (test_and_clear_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state))
 			if ((pf->flags & I40E_FLAG_FD_ATR_ENABLED) &&
 			    (I40E_DEBUG_FD & pf->hw.debug_mask))
 				dev_info(&pf->pdev->dev, "ATR re-enabled.\n");
-		}
 	}
 	return need_reset;
 }
drivers/net/ethernet/intel/i40e/i40e_txrx.c +13 -8
index 91dfe1c..c6972bd 100644
@@ -336,7 +336,7 @@ static int i40e_add_del_fdir_tcpv4(struct i40e_vsi *vsi,
 		if ((pf->flags & I40E_FLAG_FD_ATR_ENABLED) &&
 		    I40E_DEBUG_FD & pf->hw.debug_mask)
 			dev_info(&pf->pdev->dev, "Forcing ATR off, sideband rules for TCP/IPv4 flow being applied\n");
-		pf->flags |= I40E_FLAG_FD_ATR_AUTO_DISABLED;
+		set_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state);
 	} else {
 		pf->fd_tcp4_filter_cnt--;
 	}
@@ -594,8 +594,14 @@ static void i40e_fd_handle_status(struct i40e_ring *rx_ring,
 		pf->fd_atr_cnt = i40e_get_current_atr_cnt(pf);
 
 		if ((rx_desc->wb.qword0.hi_dword.fd_id == 0) &&
-		    pf->flags & I40E_FLAG_FD_SB_AUTO_DISABLED) {
-			pf->flags |= I40E_FLAG_FD_ATR_AUTO_DISABLED;
+		    test_bit(__I40E_FD_SB_AUTO_DISABLED, pf->state)) {
+			/* These set_bit() calls aren't atomic with the
+			 * test_bit() here, but worse case we potentially
+			 * disable ATR and queue a flush right after SB
+			 * support is re-enabled. That shouldn't cause an
+			 * issue in practice
+			 */
+			set_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state);
 			set_bit(__I40E_FD_FLUSH_REQUESTED, pf->state);
 		}
 
@@ -608,11 +614,10 @@ static void i40e_fd_handle_status(struct i40e_ring *rx_ring,
 		 */
 		if (fcnt_prog >= (fcnt_avail - I40E_FDIR_BUFFER_FULL_MARGIN)) {
 			if ((pf->flags & I40E_FLAG_FD_SB_ENABLED) &&
-			    !(pf->flags & I40E_FLAG_FD_SB_AUTO_DISABLED)) {
-				pf->flags |= I40E_FLAG_FD_SB_AUTO_DISABLED;
+			    !test_and_set_bit(__I40E_FD_SB_AUTO_DISABLED,
+					      pf->state))
 				if (I40E_DEBUG_FD & pf->hw.debug_mask)
 					dev_warn(&pdev->dev, "FD filter space full, new ntuple rules will not be added\n");
-			}
 		}
 	} else if (error == BIT(I40E_RX_PROG_STATUS_DESC_NO_FD_ENTRY_SHIFT)) {
 		if (I40E_DEBUG_FD & pf->hw.debug_mask)
@@ -2647,7 +2652,7 @@ static void i40e_atr(struct i40e_ring *tx_ring, struct sk_buff *skb,
 	if (!(pf->flags & I40E_FLAG_FD_ATR_ENABLED))
 		return;
 
-	if (pf->flags & I40E_FLAG_FD_ATR_AUTO_DISABLED)
+	if (test_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state))
 		return;
 
 	/* if sampling is disabled do nothing */
@@ -2687,7 +2692,7 @@ static void i40e_atr(struct i40e_ring *tx_ring, struct sk_buff *skb,
 	th = (struct tcphdr *)(hdr.network + hlen);
 
 	/* Due to lack of space, no more new filters can be programmed */
-	if (th->syn && (pf->flags & I40E_FLAG_FD_ATR_AUTO_DISABLED))
+	if (th->syn && test_bit(__I40E_FD_ATR_AUTO_DISABLED, pf->state))
 		return;
 	if (pf->flags & I40E_FLAG_HW_ATR_EVICT_ENABLED) {
 		/* HW ATR eviction will take care of removing filters on FIN
Signature · 1 line
2.9.5
#4 lore raw

PATCH 3/8 i40e: move AUTO_DISABLED flags into the state field

Quoted 24 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On Behalf Of Alice Michael
Sent: Friday, March 16, 2018 1:27 AM
To: Michael, Alice <[email protected]>; intel-wired- lan at lists.osuosl.org
Subject: [Intel-wired-lan] [next PATCH S89 3/8] i40e: move AUTO_DISABLED flags into the state field

From: Jacob Keller <[email protected]>

The two Flow Directory auto disable flags are used at run time to mark when the flow director features needed to be disabled. Thus the flags could change even when the RTNL lock is not held.

They also have some code constructions which really should be test_and_set or test_and_clear using atomic bit operations.

Create new state fields to mark this, and stop including them in pf->flags.

This is part of a larger effort to remove the need for cmpxchg64 in i40e_set_priv_flags().

Quoted 7 lines
---
 drivers/net/ethernet/intel/i40e/i40e.h         |  5 +++--
 drivers/net/ethernet/intel/i40e/i40e_ethtool.c |  4 ++--
 drivers/net/ethernet/intel/i40e/i40e_main.c    | 23 +++++++++--------------
 drivers/net/ethernet/intel/i40e/i40e_txrx.c    | 21 +++++++++++++--------
 4 files changed, 27 insertions(+), 26 deletions(-)
#5 lore raw

PATCH 4/8 i40e: move I40E_FLAG_TEMP_LINK_POLLING to state field

In reply to Alice Michael

From: Jacob Keller <[email protected]>

This flag is modified outside of the RTNL lock and thus should not be part of the pf->flags variable.

Use a state bit instead, so that we can use atomic bit operations.

This is part of a larger effort to remove cmpxchg64 in i40e_set_priv_flags()

---
 drivers/net/ethernet/intel/i40e/i40e.h      | 3 ++-
 drivers/net/ethernet/intel/i40e/i40e_main.c | 7 +++----
 2 files changed, 5 insertions(+), 5 deletions(-)
drivers/net/ethernet/intel/i40e/i40e.h +2 -1
index c41d99b..2dd89f8 100644
@@ -166,6 +166,7 @@ enum i40e_state_t {
 	__I40E_VF_DISABLE,
 	__I40E_MACVLAN_SYNC_PENDING,
 	__I40E_UDP_FILTER_SYNC_PENDING,
+	__I40E_TEMP_LINK_POLLING,
 	/* This must be last as it determines the size of the BITMAP */
 	__I40E_STATE_SIZE__,
 };
@@ -534,7 +535,7 @@ struct i40e_pf {
 #define I40E_FLAG_VEB_STATS_ENABLED		BIT_ULL(17)
 #define I40E_FLAG_LINK_POLLING_ENABLED		BIT_ULL(18)
 #define I40E_FLAG_TRUE_PROMISC_SUPPORT		BIT_ULL(19)
-#define I40E_FLAG_TEMP_LINK_POLLING		BIT_ULL(20)
+/* Gap for BIT_ULL(20) */
 #define I40E_FLAG_LEGACY_RX			BIT_ULL(21)
 #define I40E_FLAG_PTP				BIT_ULL(22)
 #define I40E_FLAG_IWARP_ENABLED			BIT_ULL(23)
drivers/net/ethernet/intel/i40e/i40e_main.c +3 -4
index 44d15cf..01ecd9d 100644
@@ -8432,13 +8432,12 @@ static void i40e_link_event(struct i40e_pf *pf)
 
 	/* On success, disable temp link polling */
 	if (status == I40E_SUCCESS) {
-		if (pf->flags & I40E_FLAG_TEMP_LINK_POLLING)
-			pf->flags &= ~I40E_FLAG_TEMP_LINK_POLLING;
+		clear_bit(__I40E_TEMP_LINK_POLLING, pf->state);
 	} else {
 		/* Enable link polling temporarily until i40e_get_link_status
 		 * returns I40E_SUCCESS
 		 */
-		pf->flags |= I40E_FLAG_TEMP_LINK_POLLING;
+		set_bit(__I40E_TEMP_LINK_POLLING, pf->state);
 		dev_dbg(&pf->pdev->dev, "couldn't get link state, status: %d\n",
 			status);
 		return;
@@ -8490,7 +8489,7 @@ static void i40e_watchdog_subtask(struct i40e_pf *pf)
 	pf->service_timer_previous = jiffies;
 
 	if ((pf->flags & I40E_FLAG_LINK_POLLING_ENABLED) ||
-	    (pf->flags & I40E_FLAG_TEMP_LINK_POLLING))
+	    test_bit(__I40E_TEMP_LINK_POLLING, pf->state))
 		i40e_link_event(pf);
 
 	/* Update the stats for active netdevs so the network stack
Signature · 1 line
2.9.5
#6 lore raw

PATCH 4/8 i40e: move I40E_FLAG_TEMP_LINK_POLLING to state field

Quoted 16 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On Behalf Of Alice Michael
Sent: Friday, March 16, 2018 1:27 AM
To: Michael, Alice <[email protected]>; intel-wired- lan at lists.osuosl.org
Subject: [Intel-wired-lan] [next PATCH S89 4/8] i40e: move I40E_FLAG_TEMP_LINK_POLLING to state field

From: Jacob Keller <[email protected]>

This flag is modified outside of the RTNL lock and thus should not be part of the pf->flags variable.

Use a state bit instead, so that we can use atomic bit operations.

Quoted 8 lines

This is part of a larger effort to remove cmpxchg64 in i40e_set_priv_flags()

---
 drivers/net/ethernet/intel/i40e/i40e.h      | 3 ++-
 drivers/net/ethernet/intel/i40e/i40e_main.c | 7 +++----
 2 files changed, 5 insertions(+), 5 deletions(-)
#7 lore raw

PATCH 5/8 i40e: move client flags into state bits

In reply to Alice Michael

From: Jacob Keller <[email protected]>

The iWarp client flags are all potentially changed when the RTNL lock is not held, so they should not be part of the pf->flags variable. Instead, move them into the state field so that we can use atomic bit operations.

This is part of a larger effort to remove cmpxchg64 in i40e_set_priv_flags()

---
 drivers/net/ethernet/intel/i40e/i40e.h        |  7 ++++---
 drivers/net/ethernet/intel/i40e/i40e_client.c |  7 +++----
 drivers/net/ethernet/intel/i40e/i40e_main.c   | 22 ++++++++++------------
 3 files changed, 17 insertions(+), 19 deletions(-)
drivers/net/ethernet/intel/i40e/i40e.h +4 -3
index 2dd89f8..029554e 100644
@@ -167,6 +167,9 @@ enum i40e_state_t {
 	__I40E_MACVLAN_SYNC_PENDING,
 	__I40E_UDP_FILTER_SYNC_PENDING,
 	__I40E_TEMP_LINK_POLLING,
+	__I40E_CLIENT_SERVICE_REQUESTED,
+	__I40E_CLIENT_L2_CHANGE,
+	__I40E_CLIENT_RESET,
 	/* This must be last as it determines the size of the BITMAP */
 	__I40E_STATE_SIZE__,
 };
@@ -539,9 +542,7 @@ struct i40e_pf {
 #define I40E_FLAG_LEGACY_RX			BIT_ULL(21)
 #define I40E_FLAG_PTP				BIT_ULL(22)
 #define I40E_FLAG_IWARP_ENABLED			BIT_ULL(23)
-#define I40E_FLAG_SERVICE_CLIENT_REQUESTED	BIT_ULL(24)
-#define I40E_FLAG_CLIENT_L2_CHANGE		BIT_ULL(25)
-#define I40E_FLAG_CLIENT_RESET			BIT_ULL(26)
+/* Gap for BIT_ULL(24) through BIT_ULL(26) */
 #define I40E_FLAG_LINK_DOWN_ON_CLOSE_ENABLED	BIT_ULL(27)
 #define I40E_FLAG_SOURCE_PRUNING_DISABLED	BIT_ULL(28)
 #define I40E_FLAG_TC_MQPRIO			BIT_ULL(29)
drivers/net/ethernet/intel/i40e/i40e_client.c +3 -4
index a04bbfc..0484c7e 100644
@@ -376,9 +376,8 @@ void i40e_client_subtask(struct i40e_pf *pf)
 	struct i40e_vsi *vsi = pf->vsi[pf->lan_vsi];
 	int ret = 0;
 
-	if (!(pf->flags & I40E_FLAG_SERVICE_CLIENT_REQUESTED))
+	if (!test_and_clear_bit(__I40E_CLIENT_SERVICE_REQUESTED, pf->state))
 		return;
-	pf->flags &= ~I40E_FLAG_SERVICE_CLIENT_REQUESTED;
 	cdev = pf->cinst;
 
 	/* If we're down or resetting, just bail */
@@ -459,7 +458,7 @@ int i40e_lan_add_device(struct i40e_pf *pf)
 	 * added, we can schedule a subtask to go initiate the clients if
 	 * they can be launched at probe time.
 	 */
-	pf->flags |= I40E_FLAG_SERVICE_CLIENT_REQUESTED;
+	set_bit(__I40E_CLIENT_SERVICE_REQUESTED, pf->state);
 	i40e_service_event_schedule(pf);
 
 out:
@@ -554,7 +553,7 @@ static void i40e_client_prepare(struct i40e_client *client)
 		pf = ldev->pf;
 		i40e_client_add_instance(pf);
 		/* Start the client subtask */
-		pf->flags |= I40E_FLAG_SERVICE_CLIENT_REQUESTED;
+		set_bit(__I40E_CLIENT_SERVICE_REQUESTED, pf->state);
 		i40e_service_event_schedule(pf);
 	}
 	mutex_unlock(&i40e_device_mutex);
drivers/net/ethernet/intel/i40e/i40e_main.c +10 -12
index 01ecd9d..debc3a3 100644
@@ -2634,8 +2634,8 @@ static int i40e_change_mtu(struct net_device *netdev, int new_mtu)
 	netdev->mtu = new_mtu;
 	if (netif_running(netdev))
 		i40e_vsi_reinit_locked(vsi);
-	pf->flags |= (I40E_FLAG_SERVICE_CLIENT_REQUESTED |
-		      I40E_FLAG_CLIENT_L2_CHANGE);
+	set_bit(__I40E_CLIENT_SERVICE_REQUESTED, pf->state);
+	set_bit(__I40E_CLIENT_L2_CHANGE, pf->state);
 	return 0;
 }
 
@@ -4722,9 +4722,9 @@ static void i40e_vsi_close(struct i40e_vsi *vsi)
 	i40e_vsi_free_tx_resources(vsi);
 	i40e_vsi_free_rx_resources(vsi);
 	vsi->current_netdev_flags = 0;
-	pf->flags |= I40E_FLAG_SERVICE_CLIENT_REQUESTED;
+	set_bit(__I40E_CLIENT_SERVICE_REQUESTED, pf->state);
 	if (test_bit(__I40E_RESET_RECOVERY_PENDING, pf->state))
-		pf->flags |=  I40E_FLAG_CLIENT_RESET;
+		set_bit(__I40E_CLIENT_RESET, pf->state);
 }
 
 /**
@@ -6495,7 +6495,7 @@ static int i40e_up_complete(struct i40e_vsi *vsi)
 	/* On the next run of the service_task, notify any clients of the new
 	 * opened netdev
 	 */
-	pf->flags |= I40E_FLAG_SERVICE_CLIENT_REQUESTED;
+	set_bit(__I40E_CLIENT_SERVICE_REQUESTED, pf->state);
 	i40e_service_event_schedule(pf);
 
 	return 0;
@@ -8037,8 +8037,8 @@ static int i40e_handle_lldp_event(struct i40e_pf *pf,
 		i40e_service_event_schedule(pf);
 	} else {
 		i40e_pf_unquiesce_all_vsi(pf);
-	pf->flags |= (I40E_FLAG_SERVICE_CLIENT_REQUESTED |
-		      I40E_FLAG_CLIENT_L2_CHANGE);
+	set_bit(__I40E_CLIENT_SERVICE_REQUESTED, pf->state);
+	set_bit(__I40E_CLIENT_L2_CHANGE, pf->state);
 	}
 
 exit:
@@ -9785,17 +9785,15 @@ static void i40e_service_task(struct work_struct *work)
 	i40e_vc_process_vflr_event(pf);
 	i40e_watchdog_subtask(pf);
 	i40e_fdir_reinit_subtask(pf);
-	if (pf->flags & I40E_FLAG_CLIENT_RESET) {
+	if (test_and_clear_bit(__I40E_CLIENT_RESET, pf->state)) {
 		/* Client subtask will reopen next time through. */
 		i40e_notify_client_of_netdev_close(pf->vsi[pf->lan_vsi], true);
-		pf->flags &= ~I40E_FLAG_CLIENT_RESET;
 	} else {
 		i40e_client_subtask(pf);
-		if (pf->flags & I40E_FLAG_CLIENT_L2_CHANGE) {
+		if (test_and_clear_bit(__I40E_CLIENT_L2_CHANGE,
+				       pf->state))
 			i40e_notify_client_of_l2_param_changes(
 							pf->vsi[pf->lan_vsi]);
-			pf->flags &= ~I40E_FLAG_CLIENT_L2_CHANGE;
-		}
 	}
 	i40e_sync_filters_subtask(pf);
 	i40e_sync_udp_filters_subtask(pf);
Signature · 1 line
2.9.5
#8 lore raw

PATCH 5/8 i40e: move client flags into state bits

Quoted 18 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On Behalf Of Alice Michael
Sent: Friday, March 16, 2018 1:27 AM
To: Michael, Alice <[email protected]>; intel-wired-
lan at lists.osuosl.org
Subject: [Intel-wired-lan] [next PATCH S89 5/8] i40e: move client flags into state bits

From: Jacob Keller <[email protected]>

The iWarp client flags are all potentially changed when the RTNL lock is not held, so they should not be part of the pf->flags variable. Instead, move them into the state field so that we can use atomic bit operations.

This is part of a larger effort to remove cmpxchg64 in i40e_set_priv_flags()

Quoted 6 lines
---
 drivers/net/ethernet/intel/i40e/i40e.h        |  7 ++++---
 drivers/net/ethernet/intel/i40e/i40e_client.c |  7 +++----
 drivers/net/ethernet/intel/i40e/i40e_main.c   | 22 ++++++++++------------
 3 files changed, 17 insertions(+), 19 deletions(-)
#9 lore raw

PATCH 6/8 i40e: hold the RTNL lock while changing interrupt schemes

In reply to Alice Michael

From: Jacob Keller <[email protected]>

When we suspend and resume, we need to clear and re-enable the interrupt scheme. This was previously not done while holding the RTNL lock, which could be problematic, because we are actually destroying and re-creating queues.

Hold the RTNL lock for the entire sequence of preparing for reset, and when resuming. This additionally protects the flags related to interrupt scheme under RTNL lock so that their modification is properly threaded.

This is part of a larger effort to remove the need for cmpxchg64 in i40e_set_priv_flags().

---
 drivers/net/ethernet/intel/i40e/i40e_main.c | 19 +++++++++++++++++--
 1 file changed, 17 insertions(+), 2 deletions(-)
drivers/net/ethernet/intel/i40e/i40e_main.c +17 -2
index debc3a3..79ab522 100644
@@ -14348,7 +14348,13 @@ static int __maybe_unused i40e_suspend(struct device *dev)
 	if (pf->wol_en && (pf->hw_features & I40E_HW_WOL_MC_MAGIC_PKT_WAKE))
 		i40e_enable_mc_magic_wake(pf);
 
-	i40e_prep_for_reset(pf, false);
+	/* Since we're going to destroy queues during the
+	 * i40e_clear_interrupt_scheme() we should hold the RTNL lock for this
+	 * whole section
+	 */
+	rtnl_lock();
+
+	i40e_prep_for_reset(pf, true);
 
 	wr32(hw, I40E_PFPM_APM, (pf->wol_en ? I40E_PFPM_APM_APME_MASK : 0));
 	wr32(hw, I40E_PFPM_WUFC, (pf->wol_en ? I40E_PFPM_WUFC_MAG_MASK : 0));
@@ -14360,6 +14366,8 @@ static int __maybe_unused i40e_suspend(struct device *dev)
 	 */
 	i40e_clear_interrupt_scheme(pf);
 
+	rtnl_unlock();
+
 	return 0;
 }
 
@@ -14377,6 +14385,11 @@ static int __maybe_unused i40e_resume(struct device *dev)
 	if (!test_bit(__I40E_SUSPENDED, pf->state))
 		return 0;
 
+	/* We need to hold the RTNL lock prior to restoring interrupt schemes,
+	 * since we're going to be restoring queues
+	 */
+	rtnl_lock();
+
 	/* We cleared the interrupt scheme when we suspended, so we need to
 	 * restore it now to resume device functionality.
 	 */
@@ -14387,7 +14400,9 @@ static int __maybe_unused i40e_resume(struct device *dev)
 	}
 
 	clear_bit(__I40E_DOWN, pf->state);
-	i40e_reset_and_rebuild(pf, false, false);
+	i40e_reset_and_rebuild(pf, false, true);
+
+	rtnl_unlock();
 
 	/* Clear suspended state last after everything is recovered */
 	clear_bit(__I40E_SUSPENDED, pf->state);
Signature · 1 line
2.9.5
#10 lore raw

PATCH 6/8 i40e: hold the RTNL lock while changing interrupt schemes

Quoted 20 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On Behalf Of Alice Michael
Sent: Friday, March 16, 2018 1:27 AM
To: Michael, Alice <[email protected]>; intel-wired-
lan at lists.osuosl.org
Subject: [Intel-wired-lan] [next PATCH S89 6/8] i40e: hold the RTNL lock while changing interrupt schemes

From: Jacob Keller <[email protected]>

When we suspend and resume, we need to clear and re-enable the interrupt scheme. This was previously not done while holding the RTNL lock, which could be problematic, because we are actually destroying and re-creating queues.

Hold the RTNL lock for the entire sequence of preparing for reset, and when resuming. This additionally protects the flags related to interrupt scheme under RTNL lock so that their modification is properly threaded.

Quoted 7 lines

This is part of a larger effort to remove the need for cmpxchg64 in i40e_set_priv_flags().

---
 drivers/net/ethernet/intel/i40e/i40e_main.c | 19 +++++++++++++++++--
 1 file changed, 17 insertions(+), 2 deletions(-)
#11 lore raw

PATCH 7/8 i40e: stop using cmpxchg flow in i40e_set_priv_flags()

In reply to Alice Michael

From: Jacob Keller <[email protected]>

Now that the only places which modify flags are either (a) during initialization prior to creating a netdevice, or (b) while holding the rtnl lock, we no longer need the cmpxchg64 call in i40e_set_priv_flags.

---
 drivers/net/ethernet/intel/i40e/i40e_ethtool.c | 19 +++++--------------
 1 file changed, 5 insertions(+), 14 deletions(-)
drivers/net/ethernet/intel/i40e/i40e_ethtool.c +5 -14
index 031bc7c..9a97f3f 100644
@@ -4436,21 +4436,12 @@ static int i40e_set_priv_flags(struct net_device *dev, u32 flags)
 		}
 	}
 
-	/* Compare and exchange the new flags into place. If we failed, that
-	 * is if cmpxchg returns anything but the old value, this means that
-	 * something else has modified the flags variable since we copied it
-	 * originally. We'll just punt with an error and log something in the
-	 * message buffer.
-	 *
-	 * This is the point of no return for this function.  We need to have
-	 * checked any discrepancies or misconfigurations and returned
-	 * EOPNOTSUPP before updating pf->flags here.
+	/* Now that we've checked to ensure that the new flags are valid, load
+	 * them into place. Since we only modify flags either (a) during
+	 * initialization or (b) while holding the RTNL lock, we don't need
+	 * anything fancy here.
 	 */
-	if (cmpxchg64(&pf->flags, orig_flags, new_flags) != orig_flags) {
-		dev_warn(&pf->pdev->dev,
-			 "Unable to update pf->flags as it was modified by another thread...\n");
-		return -EAGAIN;
-	}
+	pf->flags = new_flags;
 
 	/* Process any additional changes needed as a result of flag changes.
 	 * The changed_flags value reflects the list of bits that were
Signature · 1 line
2.9.5
#12 lore raw

PATCH 7/8 i40e: stop using cmpxchg flow in i40e_set_priv_flags()

Quoted 11 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On Behalf Of Alice Michael
Sent: Friday, March 16, 2018 1:27 AM
To: Michael, Alice <[email protected]>; intel-wired-
lan at lists.osuosl.org
Subject: [Intel-wired-lan] [next PATCH S89 7/8] i40e: stop using cmpxchg flow in i40e_set_priv_flags()

From: Jacob Keller <[email protected]>

Quoted 8 lines

Now that the only places which modify flags are either (a) during initialization prior to creating a netdevice, or (b) while holding the rtnl lock, we no longer need the cmpxchg64 call in i40e_set_priv_flags.

---
 drivers/net/ethernet/intel/i40e/i40e_ethtool.c | 19 +++++--------------
 1 file changed, 5 insertions(+), 14 deletions(-)
#13 lore raw

PATCH 8/8 i40e: re-number feature flags to remove gaps

In reply to Alice Michael

From: Jacob Keller <[email protected]>

Remove the gaps created by the recent refactor of various feature flags that have moved to the state field. Use only a u32 now that we have fewer than 32 flags in the field.

---
 drivers/net/ethernet/intel/i40e/i40e.h | 57 ++++++++++++++++------------------
 1 file changed, 26 insertions(+), 31 deletions(-)
drivers/net/ethernet/intel/i40e/i40e.h +26 -31
index 029554e..c6dcbe3 100644
@@ -518,37 +518,32 @@ struct i40e_pf {
 #define I40E_HW_RESTART_AUTONEG			BIT(18)
 #define I40E_HW_STOPPABLE_FW_LLDP		BIT(19)
 
-	u64 flags;
-#define I40E_FLAG_RX_CSUM_ENABLED		BIT_ULL(0)
-#define I40E_FLAG_MSI_ENABLED			BIT_ULL(1)
-#define I40E_FLAG_MSIX_ENABLED			BIT_ULL(2)
-#define I40E_FLAG_RSS_ENABLED			BIT_ULL(3)
-#define I40E_FLAG_VMDQ_ENABLED			BIT_ULL(4)
-/* Gap for BIT_ULL(5) */
-#define I40E_FLAG_SRIOV_ENABLED			BIT_ULL(6)
-#define I40E_FLAG_DCB_CAPABLE			BIT_ULL(7)
-#define I40E_FLAG_DCB_ENABLED			BIT_ULL(8)
-#define I40E_FLAG_FD_SB_ENABLED			BIT_ULL(9)
-#define I40E_FLAG_FD_ATR_ENABLED		BIT_ULL(10)
-/* Gap for BIT_ULL(11) and BIT_ULL(12) */
-#define I40E_FLAG_MFP_ENABLED			BIT_ULL(13)
-/* Gap for BIT_ULL(14) */
-#define I40E_FLAG_HW_ATR_EVICT_ENABLED		BIT_ULL(15)
-#define I40E_FLAG_VEB_MODE_ENABLED		BIT_ULL(16)
-#define I40E_FLAG_VEB_STATS_ENABLED		BIT_ULL(17)
-#define I40E_FLAG_LINK_POLLING_ENABLED		BIT_ULL(18)
-#define I40E_FLAG_TRUE_PROMISC_SUPPORT		BIT_ULL(19)
-/* Gap for BIT_ULL(20) */
-#define I40E_FLAG_LEGACY_RX			BIT_ULL(21)
-#define I40E_FLAG_PTP				BIT_ULL(22)
-#define I40E_FLAG_IWARP_ENABLED			BIT_ULL(23)
-/* Gap for BIT_ULL(24) through BIT_ULL(26) */
-#define I40E_FLAG_LINK_DOWN_ON_CLOSE_ENABLED	BIT_ULL(27)
-#define I40E_FLAG_SOURCE_PRUNING_DISABLED	BIT_ULL(28)
-#define I40E_FLAG_TC_MQPRIO			BIT_ULL(29)
-#define I40E_FLAG_FD_SB_INACTIVE		BIT_ULL(30)
-#define I40E_FLAG_FD_SB_TO_CLOUD_FILTER		BIT_ULL(31)
-#define I40E_FLAG_DISABLE_FW_LLDP		BIT_ULL(32)
+	u32 flags;
+#define I40E_FLAG_RX_CSUM_ENABLED		BIT(0)
+#define I40E_FLAG_MSI_ENABLED			BIT(1)
+#define I40E_FLAG_MSIX_ENABLED			BIT(2)
+#define I40E_FLAG_RSS_ENABLED			BIT(3)
+#define I40E_FLAG_VMDQ_ENABLED			BIT(4)
+#define I40E_FLAG_SRIOV_ENABLED			BIT(5)
+#define I40E_FLAG_DCB_CAPABLE			BIT(6)
+#define I40E_FLAG_DCB_ENABLED			BIT(7)
+#define I40E_FLAG_FD_SB_ENABLED			BIT(8)
+#define I40E_FLAG_FD_ATR_ENABLED		BIT(9)
+#define I40E_FLAG_MFP_ENABLED			BIT(10)
+#define I40E_FLAG_HW_ATR_EVICT_ENABLED		BIT(11)
+#define I40E_FLAG_VEB_MODE_ENABLED		BIT(12)
+#define I40E_FLAG_VEB_STATS_ENABLED		BIT(13)
+#define I40E_FLAG_LINK_POLLING_ENABLED		BIT(14)
+#define I40E_FLAG_TRUE_PROMISC_SUPPORT		BIT(15)
+#define I40E_FLAG_LEGACY_RX			BIT(16)
+#define I40E_FLAG_PTP				BIT(17)
+#define I40E_FLAG_IWARP_ENABLED			BIT(18)
+#define I40E_FLAG_LINK_DOWN_ON_CLOSE_ENABLED	BIT(19)
+#define I40E_FLAG_SOURCE_PRUNING_DISABLED       BIT(20)
+#define I40E_FLAG_TC_MQPRIO			BIT(21)
+#define I40E_FLAG_FD_SB_INACTIVE		BIT(22)
+#define I40E_FLAG_FD_SB_TO_CLOUD_FILTER		BIT(23)
+#define I40E_FLAG_DISABLE_FW_LLDP		BIT(24)
 
 	struct i40e_client_instance *cinst;
 	bool stat_offsets_loaded;
Signature · 1 line
2.9.5
#14 lore raw

PATCH 8/8 i40e: re-number feature flags to remove gaps

Quoted 15 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On Behalf Of Alice Michael
Sent: Friday, March 16, 2018 1:27 AM
To: Michael, Alice <[email protected]>; intel-wired-
lan at lists.osuosl.org
Subject: [Intel-wired-lan] [next PATCH S89 8/8] i40e: re-number feature flags to remove gaps

From: Jacob Keller <[email protected]>

Remove the gaps created by the recent refactor of various feature flags that have moved to the state field. Use only a u32 now that we have fewer than 32 flags in the field.

Quoted 5 lines
---
 drivers/net/ethernet/intel/i40e/i40e.h | 57 ++++++++++++++++--------------
----
 1 file changed, 26 insertions(+), 31 deletions(-)
#15 lore raw

PATCH 1/8 i40e: move I40E_FLAG_FILTER_SYNC to a state bit

In reply to Alice Michael
Quoted 18 lines

-----Original Message-----
From: Intel-wired-lan [mailto:intel-wired-lan-bounces at osuosl.org] On Behalf Of Alice Michael
Sent: Friday, March 16, 2018 1:27 AM
To: Michael, Alice <[email protected]>; intel-wired- lan at lists.osuosl.org
Subject: [Intel-wired-lan] [next PATCH S89 1/8] i40e: move I40E_FLAG_FILTER_SYNC to a state bit

From: Jacob Keller <[email protected]>

The I40E_FLAG_FILTER_SYNC flag is modified during run time possibly when the RTNL lock is not held. Thus, it should not be part of pf->flags, and instead should be using atomic bit operations in the pf->state field.

Create a __I40E_MACVLAN_SYNC_PENDING state bit, and use it instead of the old I40E_FLAG_FILTER_SYNC flag.

Quoted 8 lines

This is part of a larger effort to remove the need for cmpxchg64 in i40e_set_priv_flags().

---
 drivers/net/ethernet/intel/i40e/i40e.h      |  3 ++-
 drivers/net/ethernet/intel/i40e/i40e_main.c | 16 +++++++++-------
 2 files changed, 11 insertions(+), 8 deletions(-)