EAPoL over NL80211
Subsystems (2)
v6 cover EAPoL over NL80211
This patchset adds support for running 802.11 authentication mechanisms (e.g. 802.1X, 4-Way Handshake, etc) over NL80211 instead of putting them onto the network device. This has the advantage of fixing several long-standing race conditions that result from userspace operating on multiple transports in order to manage a 802.11 connection (e.g. NL80211 and wireless netdev, wlan0, etc).
For example, userspace would sometimes see 4-Way handshake packets before NL80211 signaled that the connection has been established. Leading to ugly hacks or having the STA wait for retransmissions from the AP.
This also provides a way to mitigate a particularly nasty race condition where the encryption key could be set prior to the 4-way handshake packet 4/4 being sent. This would result in the packet being sent encrypted and discarded by the peer. The mitigation strategy for this race is for userspace to explicitly tell the kernel that a particular EAPoL packet should not be encrypted.
To make this possible this patchset introduces a new NL80211 command and several new attributes. A userspace that is capable of processing EAPoL packets over NL80211 includes a new NL80211_ATTR_CONTROL_PORT_OVER_NL80211 attribute in its NL80211_CMD_ASSOCIATE or NL80211_CMD_CONNECT requests being sent to the kernel. The previously added NL80211_ATTR_SOCKET_OWNER attribute must also be included. The latter is used by the kernel to send NL80211_CMD_CONTROL_PORT_FRAME notifications back to userspace via a netlink unicast. If the NL80211_ATTR_CONTROL_PORT_OVER_NL80211 attribute is not specified, then legacy behavior is kept and control port packets continue to flow over the network interface.
If control port over nl80211 transport is requested, then control port packets are intercepted just prior to being handed to the network device and sent over netlink via the NL80211_CMD_CONTROL_PORT_FRAME notification. NL80211_ATTR_CONTROL_PORT_ETHERTYPE and NL80211_ATTR_MAC are included to specify the control port frame protocol and source address respectively. If the control port frame was received unencrypted then NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT flag is also included. NL80211_ATTR_FRAME attribute contains the raw control port frame with all transport layer headers stripped (e.g. this would be the raw EAPoL frame).
Userspace can reply to control port frames either via legacy methods (by sending frames to the network device) or via NL80211_CMD_CONTROL_PORT_FRAME request. Userspace would included NL80211_ATTR_FRAME with the raw control port frame as well as NL80211_Attr_MAC and NL80211_ATTR_CONTROL_PORT_ETHERTYPE attributes to specify the destination address and protocol respectively. This allows Pre-Authentication (protocol 0x88c7) frames to be sent via this mechanism as well. Finally, NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT flag can be included to tell the driver to send the frame unencrypted, e.g. for 4-Way handshake 4/4 frames.
The proposed patchset has been tested in a mac80211_hwsim based environment with hostapd and iwd.
ChangeLog
v6
- Dropped AP_VLAN from supported interface types in patch 2 per mailing list discussion with Johannes
- Added GENL_SET_ERR_MSG where appropriate
- Added control_port_over_nl80211 parameter to ibss_params and mesh_config
- Last patch updated to set sdata->control_port_over_nl80211 for ibss and mesh
v5
- Johannes' main comment was that we're not handling interface types other than STATION inside tx_control_port (patch 2). This patch was modified to support all interface types that seemed relevant.
- Since tx_control_port relies on wdev->conn_owner_nlportid being set, SOCKET_OWNER support was added to JOIN_IBSS, JOIN_MESH and START_AP
- SOCKET_OWNER auto-destruction logic was updated to support interface types other than STATION/P2P_CLIENT
- Last patch was modified to support control_port_over_nl80211 for mac80211 based AP mode. It also copies necessary bits for AP_VLAN interfaces.
This version has been tested on both STATION and AP mode interfaces with SOCKET_OWNER & CONTROL_PORT_OVER_NL80211 attributes provided to CMD_CONNECT and CMD_START_AP.
TODO:
- It is unclear to me how AP_VLAN and AP interfaces should synchronize on conn_owner_nlportid. This is required for tx_control_port to work.
- JOIN_IBSS & JOIN_MESH don't seem to support control_port_ethertype or control_port_no_encrypt. Should struct cfg80211_crypto_settings parsed inside nl80211_crypto_settings be added to ibss_params or mesh_config/mesh_setup?
v4
- Reordered the patches to make sure that: when CONTROL_PORT_OVER_NL80211 is provided by userspace, nl80211 checks that both EXT_FEATURE bit is set and the tx_control_port is present in rdev ops.
- Fixed up various issues Johannes found in his review
v3
- Added ETH_P_PREAUTH to if_ether.h
- Moved NL80211 feature bit from wiphy features to ext features
- Addressed various comments from Johannes
v2
- Added WIPHY_FLAG_CONTROL_PORT_OVER_NL80211 flag. This is a capability flag used by the drivers, e.g. that the driver supports control port over nl80211 capability. This capability is now checked when CONTROL_PORT_OVER_NL80211 is requested.
- mac80211 rx path now forwards Pre-Authentication frames over NL80211 as well, if requested. Tweaked the signature of cfg80211_rx_control_port.
- TX path reworked completely. tx_control_port method has been introduced to cfg80211_ops. An implementation of tx_control_port for mac80211 was added.
Denis Kenzior (11):
nl80211: Add CMD_CONTROL_PORT_FRAME API
nl80211: Implement TX of control port frames
nl80211: Add CONTROL_PORT_OVER_NL80211 attribute
cfg80211: Support all iftypes in autodisconnect_wk
nl80211: Add SOCKET_OWNER support to JOIN_IBSS
nl80211: Add SOCKET_OWNER support to JOIN_MESH
nl80211: Add SOCKET_OWNER support to START_AP
nl80211: Add control_port_over_nl80211 for ibss
nl80211: Add control_port_over_nl80211 to mesh_setup
mac80211: Add support for tx_control_port
mac80211: Send control port frames over nl80211
include/net/cfg80211.h | 40 +++++++++ include/uapi/linux/nl80211.h | 36 +++++++- net/mac80211/cfg.c | 7 ++ net/mac80211/ibss.c | 1 + net/mac80211/ieee80211_i.h | 4 + net/mac80211/iface.c | 2 + net/mac80211/main.c | 2 + net/mac80211/mlme.c | 2 + net/mac80211/rx.c | 33 ++++++-- net/mac80211/tx.c | 46 +++++++++++ net/wireless/ap.c | 1 + net/wireless/ibss.c | 1 + net/wireless/mesh.c | 1 + net/wireless/nl80211.c | 193 ++++++++++++++++++++++++++++++++++++++++++- net/wireless/rdev-ops.h | 15 ++++ net/wireless/sme.c | 43 +++++++--- net/wireless/trace.h | 47 +++++++++++ 17 files changed, 455 insertions(+), 19 deletions(-)
Signature · 1 line
2.13.5
RFC v6 1/11 nl80211: Add CMD_CONTROL_PORT_FRAME API
This commit also adds cfg80211_rx_control_port function. This is used to generate a CMD_CONTROL_PORT_FRAME event out to userspace. The conn_owner_nlportid is used as the unicast destination. This means that userspace must specify NL80211_ATTR_SOCKET_OWNER flag if control port over nl80211 routing is requested in NL80211_CMD_CONNECT, NL80211_CMD_ASSOCIATE or NL80211_CMD_START_AP
--- include/net/cfg80211.h | 22 +++++++++++++++++ include/uapi/linux/nl80211.h | 13 ++++++++++ net/wireless/nl80211.c | 58 ++++++++++++++++++++++++++++++++++++++++++++ net/wireless/trace.h | 21 ++++++++++++++++ 4 files changed, 114 insertions(+)
include/net/cfg80211.h +22 -0
@@ -5694,6 +5694,28 @@ void cfg80211_mgmt_tx_status(struct wireless_dev *wdev, u64 cookie,/** +* cfg80211_rx_control_port - notification about a received control port frame +* @dev: The device the frame matched to +* @buf: control port frame +* @len: length of the frame data +* @addr: The peer from which the frame was received +* @proto: frame protocol, typically PAE or Pre-authentication +* @unencrypted: Whether the frame was received unencrypted +* +* This function is used to inform userspace about a received control port +* frame. It should only be used if userspace indicated it wants to receive +* control port frames over NL80211. +* +* The frame is the data portion of the 802.3 or 802.11 data frame with all +* network layer headers removed (e.g. the raw EAPoL frame). +* +* Return: %true if the frame was passed to userspace +*/ +bool cfg80211_rx_control_port (struct net_device *dev, +const u8 *buf,size_t len, +const u8 *addr,u16 proto,bool unencrypted); + +/** * cfg80211_cqm_rssi_notify - connection quality monitoring rssi event * @dev: network device * @rssi_event: the triggered RSSI event
include/uapi/linux/nl80211.h +13 -0
@@ -990,6 +990,17 @@* &NL80211_CMD_CONNECT or &NL80211_CMD_ROAM. If the 4 way handshake failed * &NL80211_CMD_DISCONNECT should be indicated instead. * +* @NL80211_CMD_CONTROL_PORT_FRAME: Control Port (e.g. PAE) frame TX request +* and RX notification. This command is used both as a request to transmit +* a control port frame and as a notification that a control port frame +* has been received. %NL80211_ATTR_FRAME is used to specify the +* frame contents. The frame is the raw EAPoL data, without ethernet or +* 802.11 headers. +* When used as an event indication %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, +* %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT and %NL80211_ATTR_MAC are added +* indicating the protocol type of the received frame; whether the frame +* was received unencrypted and the MAC address of the peer respectively. +* * @NL80211_CMD_RELOAD_REGDB: Request that the regdb firmware file is reloaded. * * @NL80211_CMD_EXTERNAL_AUTH: This interface is exclusively defined for host
@@ -1228,6 +1239,8 @@ enum nl80211_commands {NL80211_CMD_STA_OPMODE_CHANGED , + NL80211_CMD_CONTROL_PORT_FRAME, +/* add new commands above here */ /* used to define NL80211_CMD_MAX below */
net/wireless/nl80211.c +58 -0
64 lines not on this page · raw message
net/wireless/trace.h +21 -0
@@ -2600,6 +2600,27 @@ TRACE_EVENT(cfg80211_mgmt_tx_status, WDEV_PR_ARG, __entry->cookie, BOOL_TO_STR(__entry->ack)) ); +TRACE_EVENT (cfg80211_rx_control_port, + TP_PROTO(struct net_device *netdev, const u8 *buf, size_t len, + const u8 *addr, u16 proto, bool unencrypted), +TP_ARGS (netdev, buf, len, addr, proto, unencrypted), +TP_STRUCT__entry ( + NETDEV_ENTRY + MAC_ENTRY(addr) + __field(u16, proto) +__field (bool, unencrypted) + ), +TP_fast_assign ( + NETDEV_ASSIGN; + MAC_ASSIGN(addr, addr); + __entry->proto = proto; + __entry->unencrypted = unencrypted; + ), +TP_printk (NETDEV_PR_FMT ", " MAC_PR_FMT " proto: %x, unencrypted: %s" , +NETDEV_PR_ARG ,MAC_PR_ARG (addr), + __entry->proto,BOOL_TO_STR (__entry->unencrypted)) +); + TRACE_EVENT(cfg80211_cqm_rssi_notify, TP_PROTO(struct net_device *netdev, enum nl80211_cqm_rssi_threshold_event rssi_event,
Signature · 1 line
2.13.5
RFC v6 2/11 nl80211: Implement TX of control port frames
In reply to Denis KenziorThis commit implements the TX side of NL80211_CMD_CONTROL_PORT_FRAME. Userspace provides the raw EAPoL frame using NL80211_ATTR_FRAME. Userspace should also provide the destination address and the protocol type to use when sending the frame. This is used to implement TX of Pre-authentication frames. If CONTROL_PORT_ETHERTYPE_NO_ENCRYPT is specified, then the driver will be asked not to encrypt the outgoing frame.
A new EXT_FEATURE flag is introduced so that nl80211 code can check whether a given wiphy has capability to pass EAPoL frames over NL80211.
--- include/net/cfg80211.h | 9 ++++++ include/uapi/linux/nl80211.h | 3 ++ net/wireless/nl80211.c | 71 +++++++++++++++++++++++++++++++++++++++++++- net/wireless/rdev-ops.h | 15 ++++++++++ net/wireless/trace.h | 26 ++++++++++++++++ 5 files changed, 123 insertions(+), 1 deletion(-)
include/net/cfg80211.h +9 -0
@@ -2960,6 +2960,9 @@ struct cfg80211_external_auth_params {* * @external_auth: indicates result of offloaded authentication processing from * user space +* +* @tx_control_port: TX a control port frame (EAPoL). The noencrypt parameter +* tells the driver that the frame should not be encrypted. */ struct cfg80211_ops {int (*suspend)(struct wiphy *wiphy,struct cfg80211_wowlan *wow);
@@ -3255,6 +3258,12 @@ struct cfg80211_ops { const u8 *aa);int (*external_auth)(struct wiphy *wiphy,struct net_device *dev,struct cfg80211_external_auth_params *params); + +int (*tx_control_port)(struct wiphy *wiphy, +struct net_device *dev, +const u8 *buf,size_t len, +const u8 *dest,const __be16 proto, +const bool noencrypt); };/*
include/uapi/linux/nl80211.h +3 -0
@@ -5012,6 +5012,8 @@ enum nl80211_feature_flags {* @NL80211_EXT_FEATURE_LOW_SPAN_SCAN: Driver supports low span scan. * @NL80211_EXT_FEATURE_LOW_POWER_SCAN: Driver supports low power scan. * @NL80211_EXT_FEATURE_HIGH_ACCURACY_SCAN: Driver supports high accuracy scan. +* @NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211: Driver supports sending and +* receiving control port frames over NL80211 instead of the netdevice. * * @NUM_NL80211_EXT_FEATURES: number of extended features. * @MAX_NL80211_EXT_FEATURES: highest extended feature index.
@@ -5042,6 +5044,7 @@ enum nl80211_ext_feature_index {NL80211_EXT_FEATURE_LOW_SPAN_SCAN ,NL80211_EXT_FEATURE_LOW_POWER_SCAN ,NL80211_EXT_FEATURE_HIGH_ACCURACY_SCAN , +NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211 ,/* add new features before the definition below */ NUM_NL80211_EXT_FEATURES,
net/wireless/nl80211.c +70 -1
83 lines not on this page · raw message
net/wireless/rdev-ops.h +15 -0
@@ -714,6 +714,21 @@ static inline int rdev_mgmt_tx(struct cfg80211_registered_device *rdev,return ret; } +static inline int rdev_tx_control_port (struct cfg80211_registered_device *rdev, +struct net_device *dev, +const void *buf,size_t len, +const u8 *dest,__be16 proto, +const bool noencrypt) +{ +int ret; +trace_rdev_tx_control_port (&rdev->wiphy, dev, buf, len, + dest, proto, noencrypt); + ret = rdev->ops->tx_control_port (&rdev->wiphy, dev, buf, len, + dest, proto, noencrypt); +trace_rdev_return_int (&rdev->wiphy, ret); +return ret; +} +static inline int rdev_mgmt_tx_cancel_wait (struct cfg80211_registered_device *rdev,struct wireless_dev *wdev,u64 cookie)
net/wireless/trace.h +26 -0
@@ -1882,6 +1882,32 @@ TRACE_EVENT(rdev_mgmt_tx, BOOL_TO_STR(__entry->dont_wait_for_ack)) ); +TRACE_EVENT (rdev_tx_control_port, + TP_PROTO(struct wiphy *wiphy, struct net_device *netdev, + const u8 *buf, size_t len, const u8 *dest, __be16 proto, + bool unencrypted), +TP_ARGS (wiphy, netdev, buf, len, dest, proto, unencrypted), +TP_STRUCT__entry ( + WIPHY_ENTRY + NETDEV_ENTRY + MAC_ENTRY(dest) + __field(__be16, proto) +__field (bool, unencrypted) + ), +TP_fast_assign ( + WIPHY_ASSIGN; + NETDEV_ASSIGN; + MAC_ASSIGN(dest, dest); + __entry->proto = proto; + __entry->unencrypted = unencrypted; + ), +TP_printk (WIPHY_PR_FMT ", " NETDEV_PR_FMT ", " MAC_PR_FMT "," +" proto: %x, unencrypted: %s" , +WIPHY_PR_ARG ,NETDEV_PR_ARG ,MAC_PR_ARG (dest), +be16_to_cpu (__entry->proto), +BOOL_TO_STR (__entry->unencrypted)) +); + TRACE_EVENT(rdev_set_noack_map, TP_PROTO(struct wiphy *wiphy, struct net_device *netdev, u16 noack_map),
Signature · 1 line
2.13.5
RFC v6 3/11 nl80211: Add CONTROL_PORT_OVER_NL80211 attribute
In reply to Denis Kenzior--- include/net/cfg80211.h | 3 +++ include/uapi/linux/nl80211.h | 14 +++++++++++++- net/wireless/nl80211.c | 26 ++++++++++++++++++++++++++ 3 files changed, 42 insertions(+), 1 deletion(-)
include/net/cfg80211.h +3 -0
@@ -646,6 +646,8 @@ struct survey_info {* allowed through even on unauthorized ports * @control_port_no_encrypt: TRUE to prevent encryption of control port * protocol frames. +* @control_port_over_nl80211: TRUE if userspace expects to exchange control +* port frames over NL80211 instead of the network interface. * @wep_keys: static WEP keys, if not NULL points to an array of * CFG80211_MAX_WEP_KEYS WEP keys * @wep_tx_key: key index (0..3) of the default TX static WEP key
@@ -661,6 +663,7 @@ struct cfg80211_crypto_settings {bool control_port;__be16 control_port_ethertype;bool control_port_no_encrypt; +bool control_port_over_nl80211;struct key_params *wep_keys;int wep_tx_key;const u8 *psk;
include/uapi/linux/nl80211.h +13 -1
@@ -542,7 +542,8 @@* IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP, * %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, -* %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT, %NL80211_ATTR_MAC_HINT, and +* %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT, +* %NL80211_ATTR_CONTROL_PORT_OVER_NL80211, %NL80211_ATTR_MAC_HINT, and * %NL80211_ATTR_WIPHY_FREQ_HINT. * If included, %NL80211_ATTR_MAC and %NL80211_ATTR_WIPHY_FREQ are * restrictions on BSS selection, i.e., they effectively prevent roaming
@@ -1488,6 +1489,15 @@ enum nl80211_commands {* @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom * ethertype frames used for key negotiation must not be encrypted. +* @NL80211_ATTR_CONTROL_PORT_OVER_NL80211: A flag indicating whether control +* port frames (e.g. of type given in %NL80211_ATTR_CONTROL_PORT_ETHERTYPE) +* will be sent directly to the network interface or sent via the NL80211 +* socket. If this attribute is missing, then legacy behavior of sending +* control port frames directly to the network interface is used. If the +* flag is included, then control port frames are sent over NL80211 instead +* using %CMD_CONTROL_PORT_FRAME. If control port routing over NL80211 is +* to be used then userspace must also use the %NL80211_ATTR_SOCKET_OWNER +* flag. * * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver. * We recommend using nested, driver-specific attributes within this.
@@ -2641,6 +2651,8 @@ enum nl80211_attrs {NL80211_ATTR_NSS ,NL80211_ATTR_ACK_SIGNAL , +NL80211_ATTR_CONTROL_PORT_OVER_NL80211 , +/* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST,
net/wireless/nl80211.c +26 -0
@@ -287,6 +287,7 @@ static const struct nla_policy nl80211_policy[NUM_NL80211_ATTR] = { [NL80211_ATTR_CONTROL_PORT] = { .type = NLA_FLAG }, [NL80211_ATTR_CONTROL_PORT_ETHERTYPE] = { .type = NLA_U16 }, [NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT] = { .type = NLA_FLAG }, + [NL80211_ATTR_CONTROL_PORT_OVER_NL80211] = { .type = NLA_FLAG }, [NL80211_ATTR_PRIVACY] = { .type = NLA_FLAG }, [NL80211_ATTR_CIPHER_SUITE_GROUP] = { .type = NLA_U32 }, [NL80211_ATTR_WPA_VERSIONS] = { .type = NLA_U32 },
@@ -8204,6 +8205,22 @@ static int nl80211_authenticate(struct sk_buff *skb, struct genl_info *info)return err; } +static int validate_pae_over_nl80211 (struct cfg80211_registered_device *rdev, +struct genl_info *info) +{ +if (!info->attrs[NL80211_ATTR_SOCKET_OWNER ]) { +GENL_SET_ERR_MSG (info,"SOCKET_OWNER not set" ); +return -EINVAL ; + } + +if (!rdev->ops->tx_control_port || + !wiphy_ext_feature_isset (&rdev->wiphy, +NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211 )) +return -EOPNOTSUPP ; + +return 0 ; +} + static int nl80211_crypto_settings(struct cfg80211_registered_device *rdev, struct genl_info *info, struct cfg80211_crypto_settings *settings,
@@ -8227,6 +8244,15 @@ static int nl80211_crypto_settings(struct cfg80211_registered_device *rdev, }else settings->control_port_ethertype =cpu_to_be16 (ETH_P_PAE ); +if (info->attrs[NL80211_ATTR_CONTROL_PORT_OVER_NL80211 ]) { +int r =validate_pae_over_nl80211 (rdev, info); + +if (r <0 ) +return r; + + settings->control_port_over_nl80211 = true; + } +if (info->attrs[NL80211_ATTR_CIPHER_SUITES_PAIRWISE ]) {void *data;int len, i;
Signature · 1 line
2.13.5
RFC v6 4/11 cfg80211: Support all iftypes in autodisconnect_wk
In reply to Denis KenziorCurrently autodisconnect_wk assumes that only interface types of P2P_CLIENT and STATION use conn_owner_nlportid. Change this so all interface types are supported.
--- net/wireless/sme.c | 43 ++++++++++++++++++++++++++++++++----------- 1 file changed, 32 insertions(+), 11 deletions(-)
net/wireless/sme.c +32 -11
@@ -1239,17 +1239,38 @@ void cfg80211_autodisconnect_wk(struct work_struct *work)wdev_lock (wdev);if (wdev->conn_owner_nlportid) { -/* -* Use disconnect_bssid if still connecting and ops->disconnect -* not implemented. Otherwise we can use cfg80211_disconnect. -*/ -if (rdev->ops->disconnect || wdev->current_bss) -cfg80211_disconnect (rdev, wdev->netdev, -WLAN_REASON_DEAUTH_LEAVING , true); -else -cfg80211_mlme_deauth (rdev, wdev->netdev, - wdev->disconnect_bssid,NULL ,0 , -WLAN_REASON_DEAUTH_LEAVING , false); +switch (wdev->iftype) { +case NL80211_IFTYPE_ADHOC : +cfg80211_leave_ibss (rdev, wdev->netdev, false); +break ; +case NL80211_IFTYPE_AP : +case NL80211_IFTYPE_P2P_GO : +cfg80211_stop_ap (rdev, wdev->netdev, false); +break ; +case NL80211_IFTYPE_MESH_POINT : +cfg80211_leave_mesh (rdev, wdev->netdev); +break ; +case NL80211_IFTYPE_STATION : +case NL80211_IFTYPE_P2P_CLIENT : +/* +* Use disconnect_bssid if still connecting and +* ops->disconnect not implemented. Otherwise we can +* use cfg80211_disconnect. +*/ +if (rdev->ops->disconnect || wdev->current_bss) +cfg80211_disconnect (rdev, wdev->netdev, +WLAN_REASON_DEAUTH_LEAVING , + true); +else +cfg80211_mlme_deauth (rdev, wdev->netdev, + wdev->disconnect_bssid, +NULL ,0 , +WLAN_REASON_DEAUTH_LEAVING , + false); +break ; +default : +break ; + } }wdev_unlock (wdev);
Signature · 1 line
2.13.5
RFC v6 5/11 nl80211: Add SOCKET_OWNER support to JOIN_IBSS
In reply to Denis Kenzior--- include/uapi/linux/nl80211.h | 2 ++ net/wireless/ibss.c | 1 + net/wireless/nl80211.c | 6 ++++++ 3 files changed, 9 insertions(+)
include/uapi/linux/nl80211.h +2 -0
@@ -1985,6 +1985,8 @@ enum nl80211_commands {* multicast group. * If set during %NL80211_CMD_ASSOCIATE or %NL80211_CMD_CONNECT the * station will deauthenticate when the socket is closed. +* If set during %NL80211_CMD_JOIN_IBSS the IBSS will be automatically +* torn down when the socket is closed. * * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is * the TDLS link initiator.
net/wireless/ibss.c +1 -0
@@ -224,6 +224,7 @@ int __cfg80211_leave_ibss(struct cfg80211_registered_device *rdev,if (err)return err; + wdev->conn_owner_nlportid =0 ;__cfg80211_clear_ibss (dev, nowext);return 0 ;
net/wireless/nl80211.c +6 -0
@@ -8704,6 +8704,12 @@ static int nl80211_join_ibss(struct sk_buff *skb, struct genl_info *info) err =cfg80211_join_ibss (rdev, dev, &ibss, connkeys);if (err)kzfree (connkeys); +else if (info->attrs[NL80211_ATTR_SOCKET_OWNER ]) { +wdev_lock (dev->ieee80211_ptr); + dev->ieee80211_ptr->conn_owner_nlportid = info->snd_portid; +wdev_unlock (dev->ieee80211_ptr); + } +return err; }
Signature · 1 line
2.13.5
RFC v6 6/11 nl80211: Add SOCKET_OWNER support to JOIN_MESH
In reply to Denis Kenzior--- include/uapi/linux/nl80211.h | 2 ++ net/wireless/mesh.c | 1 + net/wireless/nl80211.c | 10 +++++++++- 3 files changed, 12 insertions(+), 1 deletion(-)
include/uapi/linux/nl80211.h +2 -0
@@ -1987,6 +1987,8 @@ enum nl80211_commands {* station will deauthenticate when the socket is closed. * If set during %NL80211_CMD_JOIN_IBSS the IBSS will be automatically * torn down when the socket is closed. +* If set during %NL80211_CMD_JOIN_MESH the mesh setup will be +* automatically torn down when the socket is closed. * * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is * the TDLS link initiator.
net/wireless/mesh.c +1 -0
@@ -286,6 +286,7 @@ int __cfg80211_leave_mesh(struct cfg80211_registered_device *rdev, err =rdev_leave_mesh (rdev, dev);if (!err) { + wdev->conn_owner_nlportid =0 ; wdev->mesh_id_len =0 ; wdev->beacon_interval =0 ;memset (&wdev->chandef,0 ,sizeof (wdev->chandef));
net/wireless/nl80211.c +9 -1
@@ -10153,7 +10153,15 @@ static int nl80211_join_mesh(struct sk_buff *skb, struct genl_info *info) setup.userspace_handles_dfs =nla_get_flag (info->attrs[NL80211_ATTR_HANDLE_DFS ]); -return cfg80211_join_mesh (rdev, dev, &setup, &cfg); + err =cfg80211_join_mesh (rdev, dev, &setup, &cfg); + +if (!err && info->attrs[NL80211_ATTR_SOCKET_OWNER ]) { +wdev_lock (dev->ieee80211_ptr); + dev->ieee80211_ptr->conn_owner_nlportid = info->snd_portid; +wdev_unlock (dev->ieee80211_ptr); + } + +return err; }static int nl80211_leave_mesh (struct sk_buff *skb,struct genl_info *info)
Signature · 1 line
2.13.5
RFC v6 7/11 nl80211: Add SOCKET_OWNER support to START_AP
In reply to Denis Kenzior--- include/uapi/linux/nl80211.h | 2 ++ net/wireless/ap.c | 1 + net/wireless/nl80211.c | 4 ++++ 3 files changed, 7 insertions(+)
include/uapi/linux/nl80211.h +2 -0
@@ -1989,6 +1989,8 @@ enum nl80211_commands {* torn down when the socket is closed. * If set during %NL80211_CMD_JOIN_MESH the mesh setup will be * automatically torn down when the socket is closed. +* If set during %NL80211_CMD_START_AP the AP will be automatically +* disabled when the socket is closed. * * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is * the TDLS link initiator.
net/wireless/ap.c +1 -0
@@ -27,6 +27,7 @@ int __cfg80211_stop_ap(struct cfg80211_registered_device *rdev, err =rdev_stop_ap (rdev, dev);if (!err) { + wdev->conn_owner_nlportid =0 ; wdev->beacon_interval =0 ;memset (&wdev->chandef,0 ,sizeof (wdev->chandef)); wdev->ssid_len =0 ;
net/wireless/nl80211.c +4 -0
@@ -4135,6 +4135,10 @@ static int nl80211_start_ap(struct sk_buff *skb, struct genl_info *info) wdev->chandef = params.chandef; wdev->ssid_len = params.ssid_len;memcpy (wdev->ssid, params.ssid, wdev->ssid_len); + +if (info->attrs[NL80211_ATTR_SOCKET_OWNER ]) + wdev->conn_owner_nlportid = info->snd_portid; + }wdev_unlock (wdev);
Signature · 1 line
2.13.5
RFC v6 8/11 nl80211: Add control_port_over_nl80211 for ibss
In reply to Denis Kenzior--- include/net/cfg80211.h | 3 +++ net/wireless/nl80211.c | 9 +++++++++ 2 files changed, 12 insertions(+)
include/net/cfg80211.h +3 -0
@@ -2033,6 +2033,8 @@ struct cfg80211_disassoc_request {* sets/clears %NL80211_STA_FLAG_AUTHORIZED. If true, the driver is * required to assume that the port is unauthorized until authorized by * user space. Otherwise, port is marked authorized by default. +* @control_port_over_nl80211: TRUE if userspace expects to exchange control +* port frames over NL80211 instead of the network interface. * @userspace_handles_dfs: whether user space controls DFS operation, i.e. * changes the channel when a radar is detected. This is required * to operate on DFS channels.
@@ -2056,6 +2058,7 @@ struct cfg80211_ibss_params {bool channel_fixed;bool privacy;bool control_port; +bool control_port_over_nl80211;bool userspace_handles_dfs;int mcast_rate[NUM_NL80211_BANDS ];struct ieee80211_ht_cap ht_capa;
net/wireless/nl80211.c +9 -0
@@ -8702,6 +8702,15 @@ static int nl80211_join_ibss(struct sk_buff *skb, struct genl_info *info) ibss.control_port =nla_get_flag (info->attrs[NL80211_ATTR_CONTROL_PORT ]); +if (info->attrs[NL80211_ATTR_CONTROL_PORT_OVER_NL80211 ]) { +int r =validate_pae_over_nl80211 (rdev, info); + +if (r <0 ) +return r; + + ibss.control_port_over_nl80211 = true; + } + ibss.userspace_handles_dfs =nla_get_flag (info->attrs[NL80211_ATTR_HANDLE_DFS ]);
Signature · 1 line
2.13.5
RFC v6 9/11 nl80211: Add control_port_over_nl80211 to mesh_setup
In reply to Denis Kenzior--- include/net/cfg80211.h | 3 +++ net/wireless/nl80211.c | 9 +++++++++ 2 files changed, 12 insertions(+)
include/net/cfg80211.h +3 -0
@@ -1453,6 +1453,8 @@ struct mesh_config {* @userspace_handles_dfs: whether user space controls DFS operation, i.e. * changes the channel when a radar is detected. This is required * to operate on DFS channels. +* @control_port_over_nl80211: TRUE if userspace expects to exchange control +* port frames over NL80211 instead of the network interface. * * These parameters are fixed when the mesh is created. */
@@ -1475,6 +1477,7 @@ struct mesh_setup {u32 basic_rates;struct cfg80211_bitrate_mask beacon_rate;bool userspace_handles_dfs; +bool control_port_over_nl80211; };/**
net/wireless/nl80211.c +9 -0
@@ -10166,6 +10166,15 @@ static int nl80211_join_mesh(struct sk_buff *skb, struct genl_info *info) setup.userspace_handles_dfs =nla_get_flag (info->attrs[NL80211_ATTR_HANDLE_DFS ]); +if (info->attrs[NL80211_ATTR_CONTROL_PORT_OVER_NL80211 ]) { +int r =validate_pae_over_nl80211 (rdev, info); + +if (r <0 ) +return r; + + setup.control_port_over_nl80211 = true; + } + err =cfg80211_join_mesh (rdev, dev, &setup, &cfg);if (!err && info->attrs[NL80211_ATTR_SOCKET_OWNER ]) {
Signature · 1 line
2.13.5
RFC v6 10/11 mac80211: Add support for tx_control_port
In reply to Denis Kenzior--- net/mac80211/cfg.c | 1 + net/mac80211/ieee80211_i.h | 3 +++ net/mac80211/tx.c | 46 ++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 50 insertions(+)
net/mac80211/cfg.c +1 -0
@@ -3786,4 +3786,5 @@ const struct cfg80211_ops mac80211_config_ops = { .add_nan_func = ieee80211_add_nan_func, .del_nan_func = ieee80211_del_nan_func, .set_multicast_to_unicast = ieee80211_set_multicast_to_unicast, + .tx_control_port = ieee80211_tx_control_port, };
net/mac80211/ieee80211_i.h +3 -0
@@ -1734,6 +1734,9 @@ void ieee80211_check_fast_xmit(struct sta_info *sta);void ieee80211_check_fast_xmit_all (struct ieee80211_local *local);void ieee80211_check_fast_xmit_iface (struct ieee80211_sub_if_data *sdata);void ieee80211_clear_fast_xmit (struct sta_info *sta); +int ieee80211_tx_control_port (struct wiphy *wiphy,struct net_device *dev, +const u8 *buf,size_t len, +const u8 *dest,__be16 proto,bool unencrypted);/* HT */ void ieee80211_apply_htcap_overrides(struct ieee80211_sub_if_data *sdata,
net/mac80211/tx.c +46 -0
49 lines not on this page · raw message
Signature · 1 line
2.13.5
RFC v6 11/11 mac80211: Send control port frames over nl80211
In reply to Denis KenziorIf userspace requested control port frames to go over 80211, then do so. The control packets are intercepted just prior to delivery of the packet to the underlying network device.
Pre-authentication type frames (protocol: 0x88c7) are also forwarded over nl80211.
--- net/mac80211/cfg.c | 6 ++++++ net/mac80211/ibss.c | 1 + net/mac80211/ieee80211_i.h | 1 + net/mac80211/iface.c | 2 ++ net/mac80211/main.c | 2 ++ net/mac80211/mlme.c | 2 ++ net/mac80211/rx.c | 33 ++++++++++++++++++++++++++++----- 7 files changed, 42 insertions(+), 5 deletions(-)
net/mac80211/cfg.c +6 -0
@@ -925,6 +925,8 @@ static int ieee80211_start_ap(struct wiphy *wiphy, struct net_device *dev,*/ sdata->control_port_protocol = params->crypto.control_port_ethertype; sdata->control_port_no_encrypt = params->crypto.control_port_no_encrypt; + sdata->control_port_over_nl80211 = + params->crypto.control_port_over_nl80211; sdata->encrypt_headroom =ieee80211_cs_headroom (sdata->local, ¶ms->crypto, sdata->vif.type);
@@ -934,6 +936,8 @@ static int ieee80211_start_ap(struct wiphy *wiphy, struct net_device *dev, params->crypto.control_port_ethertype; vlan->control_port_no_encrypt = params->crypto.control_port_no_encrypt; + vlan->control_port_over_nl80211 = + params->crypto.control_port_over_nl80211; vlan->encrypt_headroom = ieee80211_cs_headroom(sdata->local, ¶ms->crypto,
@@ -2019,6 +2023,8 @@ static int ieee80211_join_mesh(struct wiphy *wiphy, struct net_device *dev,if (err)return err; + sdata->control_port_over_nl80211 = setup.control_port_over_nl80211; +/* can mesh use other SMPS modes? */ sdata->smps_mode =IEEE80211_SMPS_OFF ; sdata->needed_rx_chains = sdata->local->rx_chains;
net/mac80211/ibss.c +1 -0
@@ -1844,6 +1844,7 @@ int ieee80211_ibss_join(struct ieee80211_sub_if_data *sdata, sdata->smps_mode =IEEE80211_SMPS_OFF ; sdata->needed_rx_chains = local->rx_chains; + sdata->control_port_over_nl80211 = params->control_port_over_nl80211;ieee80211_queue_work (&local->hw, &sdata->work);
net/mac80211/ieee80211_i.h +1 -0
@@ -899,6 +899,7 @@ struct ieee80211_sub_if_data {u16 sequence_number;__be16 control_port_protocol;bool control_port_no_encrypt; +bool control_port_over_nl80211;int encrypt_headroom;atomic_t num_tx_queued;
net/mac80211/iface.c +2 -0
@@ -519,6 +519,8 @@ int ieee80211_do_open(struct wireless_dev *wdev, bool coming_up) master->control_port_protocol; sdata->control_port_no_encrypt = master->control_port_no_encrypt; + sdata->control_port_over_nl80211 = + master->control_port_over_nl80211; sdata->vif.cab_queue = master->vif.cab_queue;memcpy (sdata->vif.hw_queue, master->vif.hw_queue,sizeof (sdata->vif.hw_queue));
net/mac80211/main.c +2 -0
@@ -554,6 +554,8 @@ struct ieee80211_hw *ieee80211_alloc_hw_nm(size_t priv_data_len,NL80211_FEATURE_USERSPACE_MPM |NL80211_FEATURE_FULL_AP_CLIENT_STATE ;wiphy_ext_feature_set (wiphy,NL80211_EXT_FEATURE_FILS_STA ); +wiphy_ext_feature_set (wiphy, +NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211 );if (!ops->hw_scan) wiphy->features |= NL80211_FEATURE_LOW_PRIORITY_SCAN |
net/mac80211/mlme.c +2 -0
@@ -4844,6 +4844,8 @@ int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata, sdata->control_port_protocol = req->crypto.control_port_ethertype; sdata->control_port_no_encrypt = req->crypto.control_port_no_encrypt; + sdata->control_port_over_nl80211 = + req->crypto.control_port_over_nl80211; sdata->encrypt_headroom =ieee80211_cs_headroom (local, &req->crypto, sdata->vif.type);
net/mac80211/rx.c +28 -5
@@ -2245,6 +2245,32 @@ static bool ieee80211_frame_allowed(struct ieee80211_rx_data *rx, __le16 fc)return true; } +static void ieee80211_deliver_skb_to_local_stack (struct sk_buff *skb, +struct ieee80211_rx_data *rx) +{ +struct ieee80211_sub_if_data *sdata = rx->sdata; +struct net_device *dev = sdata->dev; + +if (unlikely ((skb->protocol == sdata->control_port_protocol || + skb->protocol ==cpu_to_be16 (ETH_P_PREAUTH )) && + sdata->control_port_over_nl80211)) { +struct ieee80211_rx_status *status =IEEE80211_SKB_RXCB (skb); +bool noencrypt = status->flag &RX_FLAG_DECRYPTED ; +struct ethhdr *ehdr =eth_hdr (skb); + +cfg80211_rx_control_port (dev, skb->data, skb->len, + ehdr->h_source, +be16_to_cpu (skb->protocol), noencrypt); +dev_kfree_skb (skb); + }else { +/* deliver to local stack */ +if (rx->napi) +napi_gro_receive (rx->napi, skb); +else +netif_receive_skb (skb); + } +} +/* * requires that rx->skb is a frame with ethernet header */
@@ -2329,13 +2355,10 @@ ieee80211_deliver_skb(struct ieee80211_rx_data *rx)#endif if (skb) { -/* deliver to local stack */ skb->protocol =eth_type_trans (skb, dev);memset (skb->cb,0 ,sizeof (skb->cb)); -if (rx->napi) -napi_gro_receive (rx->napi, skb); -else -netif_receive_skb (skb); + +ieee80211_deliver_skb_to_local_stack (skb, rx); }if (xmit_skb) {
Signature · 1 line
2.13.5