dmaengine: mcf-edma: add ColdFire mcf5441x eDMA support
Subsystems (3)
This patch adds dma support for NXP mcf5441x (ColdFire) family.
ColdFire mcf5441x implements an edma hw module similar to the one implemented in Vybrid VFxxx controllers, but with a slightly different register set, more dma channels (64 instead of 32), a different interrupt mechanism and some other minor differences.
For the above reasons, modfying fsl-edma.c was too complex and likely too ugly. From here, the decision to create a different driver, but starting from fsl-edma.
The driver has been tested with mcf5441x (stmark2 board) and dspi driver, it worked fine and seems reliable at least as a first initial version.
Signed-off-by Angelo Dureghello <[email protected]>
--- arch/m68k/configs/stmark2_defconfig | 2 + drivers/dma/Kconfig | 11 + drivers/dma/Makefile | 1 + drivers/dma/mcf-edma.c | 847 +++++++++++++++++++++ include/linux/platform_data/dma-mcf-edma.h | 38 + 5 files changed, 899 insertions(+) create mode 100644 drivers/dma/mcf-edma.c create mode 100644 include/linux/platform_data/dma-mcf-edma.h
arch/m68k/configs/stmark2_defconfig +2 -0
@@ -71,6 +71,8 @@ CONFIG_GPIO_GENERIC_PLATFORM=y # CONFIG_HWMON is not set # CONFIG_HID is not set # CONFIG_USB_SUPPORT is not set +CONFIG_DMADEVICES=y +CONFIG_MCF_EDMA=y # CONFIG_FILE_LOCKING is not set # CONFIG_DNOTIFY is not set # CONFIG_INOTIFY_USER is not set
drivers/dma/Kconfig +11 -0
@@ -225,6 +225,17 @@ config FSL_EDMA multiplexing capability for DMA request sources(slot). This module can be found on Freescale Vybrid and LS-1 SoCs. +config MCF_EDMA + tristate "Freescale eDMA engine support, ColdFire mcf5441x SoCs" + depends on M5441x + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + help + Support the Freescale ColdFire eDMA engine, 64-channel + implementation that performs complex data transfers with + minimal intervention from a host processor. + This module can be found on Freescale ColdFire mcf5441x SoCs. + config FSL_RAID tristate "Freescale RAID engine Support" depends on FSL_SOC && !ASYNC_TX_ENABLE_CHANNEL_SWITCH
drivers/dma/Makefile +1 -0
@@ -33,6 +33,7 @@ obj-$(CONFIG_DW_DMAC_CORE) += dw/ obj-$(CONFIG_EP93XX_DMA) += ep93xx_dma.o obj-$(CONFIG_FSL_DMA) += fsldma.o obj-$(CONFIG_FSL_EDMA) += fsl-edma.o +obj-$(CONFIG_MCF_EDMA) += mcf-edma.o obj-$(CONFIG_FSL_RAID) += fsl_raid.o obj-$(CONFIG_HSU_DMA) += hsu/ obj-$(CONFIG_IMG_MDC_DMA) += img-mdc-dma.o
drivers/dma/mcf-edma.c new file +847 -0
847 lines not on this page · raw message
include/linux/platform_data/dma-mcf-edma.h new file +38 -0
@@ -0,0 +1,38 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* +* Freescale eDMA platform data, ColdFire SoC's family. +* +* Copyright (c) 2017 Angelo Dureghello <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +*/ + +#ifndef __MACH_MCF_EDMA_H__ +#define __MACH_MCF_EDMA_H__ + +struct dma_slave_map ; + +bool mcf_edma_filter_fn (struct dma_chan *chan,void *param); + +#define MCF_EDMA_FILTER_PARAM (ch) ((void *)ch) + +/** +* struct mcf_edma_platform_data - platform specific data for eDMA engine +* +* @ver The eDMA module version. +* @dma_channels The number of eDMA channels. +*/ +struct mcf_edma_platform_data { +int dma_channels; +const struct dma_slave_map *slave_map; +int slavecnt; +}; + +#endif /* __MACH_MCF_EDMA_H__ */