kirkwood: device tree support

new file mode 100644
index 000000000000..396bcba08adb
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+	mbus at f1000000 {
+		pciec: pcie at 82000000 {
+			compatible = "marvell,kirkwood-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x04, 0xe8) 0       1 0 /* Port 0.0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x04, 0xe0) 0       1 0 /* Port 0.0 IO  */>;
+
+			pcie0: pcie at 1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x00040000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				bus-range = <0x00 0xff>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &intc 9>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gate_clk 2>;
+				status = "disabled";
+			};
+		};
+	};
+
+	ocp at f1000000 {
+		pinctrl: pin-controller at 10000 {
+			compatible = "marvell,88f6192-pinctrl";
+
+			pmx_sata0: pmx-sata0 {
+				marvell,pins = "mpp5", "mpp21", "mpp23";
+				marvell,function = "sata0";
+			};
+			pmx_sata1: pmx-sata1 {
+				marvell,pins = "mpp4", "mpp20", "mpp22";
+				marvell,function = "sata1";
+			};
+			pmx_sdio: pmx-sdio {
+				marvell,pins = "mpp12", "mpp13", "mpp14",
+					       "mpp15", "mpp16", "mpp17";
+				marvell,function = "sdio";
+			};
+		};
+
+		rtc: rtc at 10300 {
+			compatible = "marvell,kirkwood-rtc", "marvell,orion-rtc";
+			reg = <0x10300 0x20>;
+			interrupts = <53>;
+			clocks = <&gate_clk 7>;
+		};
+
+		sata: sata at 80000 {
+			compatible = "marvell,orion-sata";
+			reg = <0x80000 0x5000>;
+			interrupts = <21>;
+			clocks = <&gate_clk 14>, <&gate_clk 15>;
+			clock-names = "0", "1";
+			phys = <&sata_phy0>, <&sata_phy1>;
+			phy-names = "port0", "port1";
+			status = "disabled";
+		};
+
+		sdio: mvsdio at 90000 {
+			compatible = "marvell,orion-sdio";
+			reg = <0x90000 0x200>;
+			interrupts = <28>;
+			clocks = <&gate_clk 4>;
+			bus-width = <4>;
+			cap-sdio-irq;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			status = "disabled";
+		};
+	};
+};

90 lines not on this page · raw message

53 lines not on this page · raw message

393 lines not on this page · raw message

new file mode 100644
index 000000000000..94d9c06cbbf5
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood-dnskw.dtsi"
+
+/ {
+	model = "D-Link DNS-325 NAS (Rev A1)";
+	compatible = "dlink,dns-325-a1", "dlink,dns-325", "dlink,dns-kirkwood", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_led_power &pmx_led_red_usb_325
+			     &pmx_led_red_left_hdd &pmx_led_red_right_hdd
+			     &pmx_led_white_usb>;
+		pinctrl-names = "default";
+
+		white-power {
+			label = "dns325:white:power";
+			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+		white-usb {
+			label = "dns325:white:usb";
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; /* GPIO 43 */
+		};
+		red-l_hdd {
+			label = "dns325:red:l_hdd";
+			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+		};
+		red-r_hdd {
+			label = "dns325:red:r_hdd";
+			gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+		};
+		red-usb {
+			label = "dns325:red:usb";
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	ocp at f1000000 {
+		i2c at 11000 {
+			status = "okay";
+
+			lm75: lm75 at 48 {
+				compatible = "national,lm75";
+				reg = <0x48>;
+			};
+		};
+		serial at 12000 {
+			status = "okay";
+		};
+	};
+};

235 lines not on this page · raw message

index c46e2b447463..e010c4a42910 100644
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_DNS325=y
 CONFIG_IDENT_STRING="\nD-Link DNS-325"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dns325"
 CONFIG_BOOTDELAY=3
 CONFIG_CONSOLE_MUX=y
 # CONFIG_DISPLAY_BOARDINFO is not set

@@ -23,6 +24,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:896k(u-boot),128k(u-boot-env),5m(kernel),-(rootfs)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_MVSATA_IDE=y
 # CONFIG_MMC is not set

@@ -30,4 +32,3 @@ CONFIG_SYS_NS16550=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y

new file mode 100644
index 000000000000..6a3f1bf6d9f1
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Seagate FreeAgent Dockstar";
+	compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+		stdout-path = &uart0;
+	};
+
+	ocp at f1000000 {
+		pinctrl: pin-controller at 10000 {
+			pmx_usb_power_enable: pmx-usb-power-enable {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+			pmx_led_green: pmx-led-green {
+				marvell,pins = "mpp46";
+				marvell,function = "gpio";
+			};
+			pmx_led_orange: pmx-led-orange {
+				marvell,pins = "mpp47";
+				marvell,function = "gpio";
+			};
+		};
+		serial at 12000 {
+			status = "ok";
+		};
+	};
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_led_green &pmx_led_orange>;
+		pinctrl-names = "default";
+
+		health {
+			label = "status:green:health";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+		fault {
+			label = "status:orange:fault";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 0>;
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partition at 0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition at 100000 {
+		label = "uImage";
+		reg = <0x0100000 0x400000>;
+	};
+
+	partition at 500000 {
+		label = "data";
+		reg = <0x0500000 0xfb00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 0 {
+		compatible = "marvell,88e1116";
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};

index 88d6f596b27a..7ad184f2eb20 100644
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_DOCKSTAR=y
 CONFIG_IDENT_STRING="\nSeagate FreeAgent DockStar"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dockstar"
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_SYS_PROMPT="DockStar> "

@@ -19,10 +20,10 @@ CONFIG_CMD_JFFS2=y
 CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:1m(uboot),-(root)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 # CONFIG_MMC is not set
 CONFIG_SYS_NS16550=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y

new file mode 100644
index 000000000000..02d87e0a1061
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Seagate GoFlex Net";
+	compatible = "seagate,goflexnet", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+		stdout-path = &uart0;
+	};
+
+	ocp at f1000000 {
+		pinctrl: pin-controller at 10000 {
+			pmx_usb_power_enable: pmx-usb-power-enable {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+			pmx_led_right_cap_0: pmx-led_right_cap_0 {
+				marvell,pins = "mpp38";
+				marvell,function = "gpio";
+			};
+			pmx_led_right_cap_1: pmx-led_right_cap_1 {
+				marvell,pins = "mpp39";
+				marvell,function = "gpio";
+			};
+			pmx_led_right_cap_2: pmx-led_right_cap_2 {
+				marvell,pins = "mpp40";
+				marvell,function = "gpio";
+			};
+			pmx_led_right_cap_3: pmx-led_right_cap_3 {
+				marvell,pins = "mpp41";
+				marvell,function = "gpio";
+			};
+			pmx_led_left_cap_0: pmx-led_left_cap_0 {
+				marvell,pins = "mpp42";
+				marvell,function = "gpio";
+			};
+			pmx_led_left_cap_1: pmx-led_left_cap_1 {
+				marvell,pins = "mpp43";
+				marvell,function = "gpio";
+			};
+			pmx_led_left_cap_2: pmx-led_left_cap_2 {
+				marvell,pins = "mpp44";
+				marvell,function = "gpio";
+			};
+			pmx_led_left_cap_3: pmx-led_left_cap_3 {
+				marvell,pins = "mpp45";
+				marvell,function = "gpio";
+			};
+			pmx_led_green: pmx-led_green {
+				marvell,pins = "mpp46";
+				marvell,function = "gpio";
+			};
+			pmx_led_orange: pmx-led_orange {
+				marvell,pins = "mpp47";
+				marvell,function = "gpio";
+			};
+		};
+		serial at 12000 {
+			status = "ok";
+		};
+
+		sata at 80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+
+	};
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = < &pmx_led_orange
+			      &pmx_led_left_cap_0 &pmx_led_left_cap_1
+			      &pmx_led_left_cap_2 &pmx_led_left_cap_3
+			      &pmx_led_right_cap_0 &pmx_led_right_cap_1
+			      &pmx_led_right_cap_2 &pmx_led_right_cap_3
+			    >;
+		pinctrl-names = "default";
+
+		health {
+			label = "status:green:health";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+		fault {
+			label = "status:orange:fault";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+		left0 {
+			label = "status:white:left0";
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+		left1 {
+			label = "status:white:left1";
+			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		};
+		left2 {
+			label = "status:white:left2";
+			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		};
+		left3 {
+			label = "status:white:left3";
+			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		};
+		right0 {
+			label = "status:white:right0";
+			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		};
+		right1 {
+			label = "status:white:right1";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+		right2 {
+			label = "status:white:right2";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+		right3 {
+			label = "status:white:right3";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		};
+	};
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&nand {
+	chip-delay = <40>;
+	status = "okay";
+
+	partition at 0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition at 100000 {
+		label = "uImage";
+		reg = <0x0100000 0x400000>;
+	};
+
+	partition at 500000 {
+		label = "pogoplug";
+		reg = <0x0500000 0x2000000>;
+	};
+
+	partition at 2500000 {
+		label = "root";
+		reg = <0x02500000 0xd800000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};

index d87d308ac097..7f85c4fa17bb 100644
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_GOFLEXHOME=y
 CONFIG_IDENT_STRING="\nSeagate GoFlex Home"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-goflexnet"
 CONFIG_BOOTDELAY=3
 CONFIG_CONSOLE_MUX=y
 # CONFIG_DISPLAY_BOARDINFO is not set

@@ -24,6 +25,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:1m(uboot),6M(uImage),-(root)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_MVSATA_IDE=y
 # CONFIG_MMC is not set

@@ -31,4 +33,3 @@ CONFIG_SYS_NS16550=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y

new file mode 100644
index 000000000000..ff1260ee3fe8
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Globalscale Technologies Guruplug Server Plus";
+	compatible = "globalscale,guruplug-server-plus", "globalscale,guruplug", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	ocp at f1000000 {
+		pinctrl: pin-controller at 10000 {
+			pmx_led_health_r: pmx-led-health-r {
+				marvell,pins = "mpp46";
+				marvell,function = "gpio";
+			};
+			pmx_led_health_g: pmx-led-health-g {
+				marvell,pins = "mpp47";
+				marvell,function = "gpio";
+			};
+			pmx_led_wmode_r: pmx-led-wmode-r {
+				marvell,pins = "mpp48";
+				marvell,function = "gpio";
+			};
+			pmx_led_wmode_g: pmx-led-wmode-g {
+				marvell,pins = "mpp49";
+				marvell,function = "gpio";
+			};
+		};
+		serial at 12000 {
+			status = "ok";
+		};
+
+		sata at 80000 {
+			status = "okay";
+			nr-ports = <1>;
+		};
+
+		/* AzureWave AW-GH381 WiFi/BT */
+		mvsdio at 90000 {
+			status = "okay";
+			non-removable;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g
+			      &pmx_led_wmode_r &pmx_led_wmode_g >;
+		pinctrl-names = "default";
+
+		health-r {
+			label = "guruplug:red:health";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+		health-g {
+			label = "guruplug:green:health";
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+		wmode-r {
+			label = "guruplug:red:wmode";
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+		};
+		wmode-g {
+			label = "guruplug:green:wmode";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partition at 0 {
+		label = "u-boot";
+		reg = <0x00000000 0x00100000>;
+		read-only;
+	};
+
+	partition at 100000 {
+		label = "uImage";
+		reg = <0x00100000 0x00400000>;
+	};
+
+	partition at 500000 {
+		label = "data";
+		reg = <0x00500000 0x1fb00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 0 {
+		/* Marvell 88E1121R */
+		compatible = "ethernet-phy-id0141.0cb0",
+		             "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+
+	ethphy1: ethernet-phy at 1 {
+		/* Marvell 88E1121R */
+		compatible = "ethernet-phy-id0141.0cb0",
+		             "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+		phy-connection-type = "rgmii-id";
+	};
+};
+
+&eth1 {
+	status = "okay";
+	ethernet1-port at 0 {
+		phy-handle = <&ethphy1>;
+		phy-connection-type = "rgmii-id";
+	};
+};

index c4889910687f..66c34fcc34bc 100644
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_GURUPLUG=y
 CONFIG_IDENT_STRING="\nMarvell-GuruPlug"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-guruplug-server-plus"
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_HUSH_PARSER=y

@@ -24,6 +25,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:896K(uboot),128K(uboot_env),- at 1M(root)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_MVSATA_IDE=y
 # CONFIG_MMC is not set

@@ -32,4 +34,3 @@ CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
 CONFIG_LZMA=y
-CONFIG_OF_LIBFDT=y

new file mode 100644
index 000000000000..962a910a6f5c
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)";
+	compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	ocp at f1000000 {
+		pinctrl: pin-controller at 10000 {
+			pmx_led_os_red: pmx-led-os-red {
+				marvell,pins = "mpp22";
+				marvell,function = "gpio";
+			};
+			pmx_power_off: pmx-power-off {
+				marvell,pins = "mpp24";
+				marvell,function = "gpio";
+			};
+			pmx_led_os_green: pmx-led-os-green {
+				marvell,pins = "mpp25";
+				marvell,function = "gpio";
+			};
+			pmx_led_usb_transfer: pmx-led-usb-transfer {
+				marvell,pins = "mpp27";
+				marvell,function = "gpio";
+			};
+			pmx_button_reset: pmx-button-reset {
+				marvell,pins = "mpp28";
+				marvell,function = "gpio";
+			};
+			pmx_button_usb_copy: pmx-button-usb-copy {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+		};
+
+		serial at 12000 {
+			status = "okay";
+		};
+
+		sata at 80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_button_reset &pmx_button_usb_copy>;
+		pinctrl-names = "default";
+
+		copy {
+			label = "USB Copy";
+			linux,code = <KEY_COPY>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		};
+		reset {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_led_os_red &pmx_led_os_green
+			     &pmx_led_usb_transfer>;
+		pinctrl-names = "default";
+
+		green-os {
+			label = "ib62x0:green:os";
+			gpios = <&gpio0 25 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+		red-os {
+			label = "ib62x0:red:os";
+			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+		};
+		usb-copy {
+			label = "ib62x0:red:usb_copy";
+			gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio_poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&pmx_power_off>;
+		pinctrl-names = "default";
+		gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partition at 0 {
+		label = "u-boot";
+		reg = <0x0000000 0xe0000>;
+	};
+
+	partition at e0000 {
+		label = "u-boot environment";
+		reg = <0xe0000 0x20000>;
+	};
+
+	partition at 100000 {
+		label = "uImage";
+		reg = <0x0100000 0x600000>;
+	};
+
+	partition at 700000 {
+		label = "root";
+		reg = <0x0700000 0xf900000>;
+	};
+
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 8 {
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};

index 9a067e36cc00..1dd6b419d1ea 100644
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_IB62X0=y
 CONFIG_IDENT_STRING=" RaidSonic ICY BOX IB-NAS62x0"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ib62x0"
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_HUSH_PARSER=y

@@ -22,6 +23,7 @@ CONFIG_CMD_JFFS2=y
 CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0xe0000 at 0x0(uboot),0x20000 at 0xe0000(uboot_env),- at 0x100000(root)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_MVSATA_IDE=y
 # CONFIG_MMC is not set

@@ -30,4 +32,3 @@ CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
 CONFIG_LZMA=y
-CONFIG_OF_LIBFDT=y

new file mode 100644
index 000000000000..4a512d80912c
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Iomega Iconnect";
+	compatible = "iom,iconnect-1.1", "iom,iconnect", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+		linux,initrd-start = <0x4500040>;
+		linux,initrd-end   = <0x4800000>;
+	};
+
+	ocp at f1000000 {
+		pinctrl: pin-controller at 10000 {
+			pmx_button_reset: pmx-button-reset {
+				marvell,pins = "mpp12";
+				marvell,function = "gpio";
+			};
+			pmx_button_otb: pmx-button-otb {
+				marvell,pins = "mpp35";
+				marvell,function = "gpio";
+			};
+			pmx_led_level: pmx-led-level {
+				marvell,pins = "mpp41";
+				marvell,function = "gpio";
+			};
+			pmx_led_power_blue: pmx-led-power-blue {
+				marvell,pins = "mpp42";
+				marvell,function = "gpio";
+			};
+			pmx_led_power_red: pmx-power-red {
+				marvell,pins = "mpp43";
+				marvell,function = "gpio";
+			};
+			pmx_led_usb1: pmx-led-usb1 {
+				marvell,pins = "mpp44";
+				marvell,function = "gpio";
+			};
+			pmx_led_usb2: pmx-led-usb2 {
+				marvell,pins = "mpp45";
+				marvell,function = "gpio";
+			};
+			pmx_led_usb3: pmx-led-usb3 {
+				marvell,pins = "mpp46";
+				marvell,function = "gpio";
+			};
+			pmx_led_usb4: pmx-led-usb4 {
+				marvell,pins = "mpp47";
+				marvell,function = "gpio";
+			};
+			pmx_led_otb: pmx-led-otb {
+				marvell,pins = "mpp48";
+				marvell,function = "gpio";
+			};
+		};
+		i2c at 11000 {
+			status = "okay";
+
+			lm63: lm63 at 4c {
+				compatible = "national,lm63";
+				reg = <0x4c>;
+			};
+		};
+		serial at 12000 {
+			status = "ok";
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = < &pmx_led_level &pmx_led_power_blue
+			      &pmx_led_power_red &pmx_led_usb1
+			      &pmx_led_usb2 &pmx_led_usb3
+			      &pmx_led_usb4 &pmx_led_otb >;
+		pinctrl-names = "default";
+
+		led-level {
+			label = "led_level";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+		power-blue {
+			label = "power:blue";
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+		power-red {
+			label = "power:red";
+			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+		};
+		usb1 {
+			label = "usb1:blue";
+			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		};
+		usb2 {
+			label = "usb2:blue";
+			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+		};
+		usb3 {
+			label = "usb3:blue";
+			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		};
+		usb4 {
+			label = "usb4:blue";
+			gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+		};
+		otb {
+			label = "otb:blue";
+			gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = < &pmx_button_reset &pmx_button_otb >;
+		pinctrl-names = "default";
+
+		otb {
+			label = "OTB Button";
+			linux,code = <KEY_COPY>;
+			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+			debounce-interval = <100>;
+		};
+		reset {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+			debounce-interval = <100>;
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partition at 0 {
+		label = "uboot";
+		reg = <0x0000000 0xc0000>;
+	};
+
+	partition at a0000 {
+		label = "env";
+		reg = <0xa0000 0x20000>;
+	};
+
+	partition at 100000 {
+		label = "zImage";
+		reg = <0x100000 0x300000>;
+	};
+
+	partition at 540000 {
+		label = "initrd";
+		reg = <0x540000 0x300000>;
+	};
+
+	partition at 980000 {
+		label = "boot";
+		reg = <0x980000 0x1f400000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 11 {
+		reg = <11>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};
+
+&pciec {
+        status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};

index 80b8ff999a55..236b91df45e6 100644
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_ICONNECT=y
 CONFIG_IDENT_STRING=" Iomega iConnect"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-iconnect"
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_SYS_PROMPT="iconnect => "

@@ -18,6 +19,7 @@ CONFIG_CMD_JFFS2=y
 CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0x80000 at 0x0(uboot),0x20000 at 0x80000(uboot_env),- at 0xa0000(rootfs)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 # CONFIG_MMC is not set
 CONFIG_SYS_NS16550=y

@@ -25,4 +27,3 @@ CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
 CONFIG_LZMA=y
-CONFIG_OF_LIBFDT=y

new file mode 100644
index 000000000000..07fbfca444d5
@@ -0,0 +1,172 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Device Tree file for Seagate Blackarmor NAS220
+ *
+ * Copyright (C) 2014 Evgeni Dobrev <[email protected]>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "kirkwood.dtsi"
+#include "kirkwood-6192.dtsi"
+
+/ {
+	model = "Seagate Blackarmor NAS220";
+	compatible = "seagate,blackarmor-nas220","marvell,kirkwood-88f6192",
+		     "marvell,kirkwood";
+
+	memory { /* 128 MB */
+		device_type = "memory";
+		reg = <0x00000000 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	gpio_poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "Reset";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+
+		button {
+			label = "Power";
+			linux,code = <KEY_SLEEP>;
+			gpios = <&gpio0 26 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		blue-power {
+			label = "nas220:blue:power";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_power_sata0 &pmx_power_sata1>;
+		pinctrl-names = "default";
+
+		sata0_power: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "SATA0 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 24 GPIO_ACTIVE_LOW>;
+		};
+
+		sata1_power: regulator at 2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "SATA1 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/*
+ * Serial port routed to connector CN5
+ *
+ * pin 1 - TX (CPU's TX)
+ * pin 4 - RX (CPU's RX)
+ * pin 6 - GND
+ */
+&uart0 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-0 = <&pmx_button_reset &pmx_button_power>;
+	pinctrl-names = "default";
+
+	pmx_act_sata0: pmx-act-sata0 {
+		marvell,pins = "mpp15";
+		marvell,function = "sata0";
+	};
+
+	pmx_act_sata1: pmx-act-sata1 {
+		marvell,pins = "mpp16";
+		marvell,function = "sata1";
+	};
+
+	pmx_power_sata0: pmx-power-sata0 {
+		marvell,pins = "mpp24";
+		marvell,function = "gpio";
+	};
+
+	pmx_power_sata1: pmx-power-sata1 {
+		marvell,pins = "mpp28";
+		marvell,function = "gpio";
+	};
+
+	pmx_button_reset: pmx-button-reset {
+		marvell,pins = "mpp29";
+		marvell,function = "gpio";
+	};
+
+	pmx_button_power: pmx-button-power {
+		marvell,pins = "mpp26";
+		marvell,function = "gpio";
+	};
+};
+
+&sata {
+	status = "okay";
+	nr-ports = <2>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	adt7476: thermal at 2e {
+		compatible = "adi,adt7476";
+		reg = <0x2e>;
+	};
+};
+
+&nand {
+	status = "okay";
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 8 {
+		 reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};

index 75ea85bad4c6..06918eee2334 100644
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_NAS220=y
 CONFIG_IDENT_STRING="\nNAS 220"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-blackarmor-nas220"
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_HUSH_PARSER=y

@@ -24,6 +25,7 @@ CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
 CONFIG_EFI_PARTITION=y
 # CONFIG_PARTITION_UUIDS is not set
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_MVSATA_IDE=y
 # CONFIG_MMC is not set

@@ -31,4 +33,3 @@ CONFIG_SYS_NS16550=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y

new file mode 100644
index 000000000000..9b861c2e76c5
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood-nsa3x0-common.dtsi"
+
+/ {
+	compatible = "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+
+	ocp at f1000000 {
+		pinctrl: pin-controller at 10000 {
+			pinctrl-0 = <&pmx_unknown>;
+			pinctrl-names = "default";
+
+			pmx_led_esata_green: pmx-led-esata-green {
+				marvell,pins = "mpp12";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_esata_red: pmx-led-esata-red {
+				marvell,pins = "mpp13";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_usb_green: pmx-led-usb-green {
+				marvell,pins = "mpp15";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_usb_red: pmx-led-usb-red {
+				marvell,pins = "mpp16";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_green: pmx-led-sys-green {
+				marvell,pins = "mpp28";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_sys_red: pmx-led-sys-red {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd_green: pmx-led-hdd-green {
+				marvell,pins = "mpp41";
+				marvell,function = "gpio";
+			};
+
+			pmx_led_hdd_red: pmx-led-hdd-red {
+				marvell,pins = "mpp42";
+				marvell,function = "gpio";
+			};
+
+			pmx_unknown: pmx-unknown {
+				marvell,pins = "mpp44";
+				marvell,function = "gpio";
+			};
+
+		};
+
+		i2c at 11000 {
+			status = "okay";
+
+			adt7476: adt7476a at 2e {
+				compatible = "adi,adt7476";
+				reg = <0x2e>;
+			};
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_led_esata_green &pmx_led_esata_red
+			     &pmx_led_usb_green &pmx_led_usb_red
+			     &pmx_led_sys_green &pmx_led_sys_red
+			     &pmx_led_copy_green &pmx_led_copy_red
+			     &pmx_led_hdd_green &pmx_led_hdd_red>;
+		pinctrl-names = "default";
+
+		green-sys {
+			label = "nsa310:green:sys";
+			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+		};
+		red-sys {
+			label = "nsa310:red:sys";
+			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+		green-hdd {
+			label = "nsa310:green:hdd";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		};
+		red-hdd {
+			label = "nsa310:red:hdd";
+			gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		};
+		green-esata {
+			label = "nsa310:green:esata";
+			gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		};
+		red-esata {
+			label = "nsa310:red:esata";
+			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+		green-usb {
+			label = "nsa310:green:usb";
+			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+		};
+		red-usb {
+			label = "nsa310:red:usb";
+			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+		};
+		green-copy {
+			label = "nsa310:green:copy";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+		red-copy {
+			label = "nsa310:red:copy";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pciec {
+        status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};

158 lines not on this page · raw message

index 2529687414fa..d3ea933d378b 100644
@@ -2,6 +2,7 @@ CONFIG_ARM=y
 CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_NSA310S=y
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-nsa310"
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_HUSH_PARSER=y

@@ -21,6 +22,7 @@ CONFIG_CMD_JFFS2=y
 CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:0xe0000 at 0x0(uboot),0x20000 at 0xe0000(uboot_env),0x100000 at 0x100000(second_stage_uboot),- at 0x200000(root)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_MVSATA_IDE=y
 # CONFIG_MMC is not set

@@ -29,4 +31,3 @@ CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
 CONFIG_LZMA=y
-CONFIG_OF_LIBFDT=y

new file mode 100644
index 000000000000..094191ece3d7
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Marvell OpenRD Base Board Description
+ *
+ * Andrew Lunn <[email protected]>
+ *
+ * This file contains the definitions that are specific to OpenRD
+ * base variant of the Marvell Kirkwood Development Board.
+ */
+
+/dts-v1/;
+
+#include "kirkwood-openrd.dtsi"
+
+/ {
+	model = "OpenRD Base";
+	compatible = "marvell,openrd-base", "marvell,openrd", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	ocp at f1000000 {
+		serial at 12100 {
+			status = "okay";
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 8 {
+		reg = <8>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};

73 lines not on this page · raw message

55 lines not on this page · raw message

122 lines not on this page · raw message

index 75ebb22f2d3e..650ac5766e4e 100644
@@ -4,6 +4,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_OPENRD=y
 CONFIG_IDENT_STRING="\nOpenRD-Base"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-openrd-base"
 CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_BASE"
 CONFIG_BOOTDELAY=3
 CONFIG_LOGLEVEL=2

@@ -24,6 +25,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=nand_mtd"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=nand_mtd:0x100000 at 0x000000(uboot),0x400000 at 0x100000(uImage),0x1fb00000 at 0x500000(rootfs)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_MVSATA_IDE=y
 # CONFIG_MMC_HW_PARTITIONING is not set

@@ -31,4 +33,3 @@ CONFIG_SYS_NS16550=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y

index 533a4032488f..b139994f0a0c 100644
@@ -4,6 +4,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_OPENRD=y
 CONFIG_IDENT_STRING="\nOpenRD-Client"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-openrd-client"
 CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_CLIENT"
 CONFIG_BOOTDELAY=3
 CONFIG_LOGLEVEL=2

@@ -24,6 +25,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=nand_mtd"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=nand_mtd:0x100000 at 0x000000(uboot),0x400000 at 0x100000(uImage),0x1fb00000 at 0x500000(rootfs)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_MVSATA_IDE=y
 # CONFIG_MMC_HW_PARTITIONING is not set

@@ -31,4 +33,3 @@ CONFIG_SYS_NS16550=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y

index db90072978f1..dfadcca9d9f6 100644
@@ -4,6 +4,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_OPENRD=y
 CONFIG_IDENT_STRING="\nOpenRD-Ultimate"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-openrd-ultimate"
 CONFIG_SYS_EXTRA_OPTIONS="BOARD_IS_OPENRD_ULTIMATE"
 CONFIG_BOOTDELAY=3
 CONFIG_LOGLEVEL=2

@@ -24,6 +25,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=nand_mtd"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=nand_mtd:0x100000 at 0x000000(uboot),0x400000 at 0x100000(uImage),0x1fb00000 at 0x500000(rootfs)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_MVSATA_IDE=y
 # CONFIG_MMC_HW_PARTITIONING is not set

@@ -31,4 +33,3 @@ CONFIG_SYS_NS16550=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y

new file mode 100644
index 000000000000..f9e95e55f36d
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * kirkwood-pogo_e02.dts - Device tree file for Pogoplug E02
+ *
+ * Copyright (C) 2015 Christoph Junghans <[email protected]>
+ *
+ * based on information of dts files from
+ *  Arch Linux ARM by Oleg Rakhmanov <[email protected]>
+ *  OpenWrt by Felix Kaechele <[email protected]>
+ *
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	model = "Cloud Engines Pogoplug E02";
+	compatible = "cloudengines,pogoe02", "marvell,kirkwood-88f6281",
+		     "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+
+		health {
+			label = "pogo_e02:green:health";
+			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+		fault {
+			label = "pogo_e02:orange:fault";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pinctrl {
+	pinctrl-0 = < &pmx_usb_power_enable &pmx_led_orange
+		      &pmx_led_green >;
+	pinctrl-names = "default";
+
+	pmx_usb_power_enable: pmx-usb-power-enable {
+		marvell,pins = "mpp29";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_green: pmx-led-green {
+		marvell,pins = "mpp48";
+		marvell,function = "gpio";
+	};
+
+	pmx_led_orange: pmx-led-orange {
+		marvell,pins = "mpp49";
+		marvell,function = "gpio";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&nand {
+	chip-delay = <40>;
+	status = "okay";
+
+	partition at 0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition at 100000 {
+		label = "uImage";
+		reg = <0x0100000 0x400000>;
+	};
+
+	partition at 500000 {
+		label = "pogoplug";
+		reg = <0x0500000 0x2000000>;
+	};
+
+	partition at 2500000 {
+		label = "root";
+		reg = <0x02500000 0x5b00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};

index 8e01582b5565..94a3b1aedb76 100644
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_POGO_E02=y
 CONFIG_IDENT_STRING="\nPogo E02"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-pogo_e02"
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_SYS_PROMPT="PogoE02> "

@@ -18,10 +19,10 @@ CONFIG_CMD_FAT=y
 CONFIG_CMD_JFFS2=y
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 # CONFIG_MMC is not set
 CONFIG_SYS_NS16550=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
-CONFIG_OF_LIBFDT=y

new file mode 100644
index 000000000000..0a698d3b7393
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * kirkwood-sheevaplug-common.dtsi - Common parts for Sheevaplugs
+ *
+ * Copyright (C) 2013 Simon Baatz <[email protected]>
+ */
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	ocp at f1000000 {
+		pinctrl: pin-controller at 10000 {
+
+			pmx_usb_power_enable: pmx-usb-power-enable {
+				marvell,pins = "mpp29";
+				marvell,function = "gpio";
+			};
+			pmx_led_red: pmx-led-red {
+				marvell,pins = "mpp46";
+				marvell,function = "gpio";
+			};
+			pmx_led_blue: pmx-led-blue {
+				marvell,pins = "mpp49";
+				marvell,function = "gpio";
+			};
+			pmx_sdio_cd: pmx-sdio-cd {
+				marvell,pins = "mpp44";
+				marvell,function = "gpio";
+			};
+			pmx_sdio_wp: pmx-sdio-wp {
+				marvell,pins = "mpp47";
+				marvell,function = "gpio";
+			};
+		};
+		serial at 12000 {
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_usb_power_enable>;
+		pinctrl-names = "default";
+
+		usb_power: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "USB Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 29 0>;
+		};
+	};
+};
+
+&nand {
+	status = "okay";
+
+	partition at 0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+	};
+
+	partition at 100000 {
+		label = "uImage";
+		reg = <0x0100000 0x400000>;
+	};
+
+	partition at 500000 {
+		label = "root";
+		reg = <0x0500000 0x1fb00000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy at 0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port at 0 {
+		phy-handle = <&ethphy0>;
+	};
+};

42 lines not on this page · raw message

index d921666ae846..1e4068bf9c36 100644
@@ -3,6 +3,7 @@ CONFIG_KIRKWOOD=y
 CONFIG_SYS_TEXT_BASE=0x600000
 CONFIG_TARGET_SHEEVAPLUG=y
 CONFIG_IDENT_STRING="\nMarvell-Sheevaplug"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-sheevaplug"
 CONFIG_BOOTDELAY=3
 # CONFIG_DISPLAY_BOARDINFO is not set
 CONFIG_HUSH_PARSER=y

@@ -25,6 +26,7 @@ CONFIG_MTDIDS_DEFAULT="nand0=orion_nand"
 CONFIG_MTDPARTS_DEFAULT="mtdparts=orion_nand:512K(uboot),512K(env),4M(kernel),-(rootfs)"
 CONFIG_CMD_UBI=y
 CONFIG_ISO_PARTITION=y
+CONFIG_OF_CONTROL=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_MVSATA_IDE=y
 CONFIG_SYS_NS16550=y

@@ -32,4 +34,3 @@ CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_STORAGE=y
 CONFIG_LZMA=y
-CONFIG_OF_LIBFDT=y