dt-bindings: add binding for Rockchip hdmi phy using an Innosilicon IP
Subsystems (3)
Heiko Stuebner
maintainerPATCH v3 1/2 dt-bindings: add binding for Rockchip hdmi phy using an Innosilicon IP
From: Zheng Yang <[email protected]>
The phy is used so far in two Rockchip socs the rk3228 and the rk3328.
---
changes in v3:
- describe both refclks supplied to the phy block
.../bindings/phy/phy-rockchip-inno-hdmi.txt | 43 +++++++++++++++++++ 1 file changed, 43 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt
Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt new file +43 -0
@@ -0,0 +1,43 @@ +ROCKCHIP HDMI PHY WITH INNO IP BLOCK + +Required properties: + - compatible : should be one of the listed compatibles: + * "rockchip,rk3228-hdmi-phy", + * "rockchip,rk3328-hdmi-phy"; + - reg : Address and length of the hdmi phy control register set + - clocks : phandle + clock specifier for the phy clocks + - clock-names : string, clock name, must contain "sysclk" for system + control and register configuration, "refoclk" for crystal- + oscillator reference PLL clock input and "refpclk" for pclk- + based refeference PLL clock input. + - #clock-cells: should be 0. + - clock-output-names : shall be the name for the output clock. + - interrupts : phandle + interrupt specified for the hdmiphy interrupt + - #phy-cells : must be 0. See ./phy-bindings.txt for details. + +Optional properties for rk3328-hdmi-phy: + - nvmem-cells = phandle + nvmem specifier for the cpu-version efuse + - nvmem-cell-names : "cpu-version" to read the chip version, required + for adjustment to some frequency settings + +Example: + hdmi_phy: hdmi-phy at 12030000 { + compatible = "rockchip,rk3228-hdmi-phy"; + reg = <0x12030000 0x10000>; + #phy-cells = <0>; + clocks = <&cru PCLK_HDMI_PHY>, <&xin24m>, <&cru DCLK_HDMIPHY>; + clock-names = "sysclk", "refoclk", "refpclk"; + #clock-cells = <0>; + clock-output-names = "hdmi_phy"; + status = "disabled"; + }; + +Then the PHY can be used in other nodes such as: + + hdmi: hdmi at 200a0000 { + compatible = "rockchip,rk3228-dw-hdmi"; + ... + phys = <&hdmi_phy>; + phy-names = "hdmi"; + ... + };
Signature · 1 line
2.17.0
Heiko Stuebner
maintainerPATCH v3 2/2 phy: add Rockchip Innosilicon hdmi phy
From: Zheng Yang <[email protected]>
Add a driver for the Innosilicon hdmi phy used on rk3228/rk3229 and rk3328 socs from Rockchip.
---
changes in v3:
- included real recalc_rate for rk3228
- claim both refclks and keep the refpclk on
to make rk3328 happy for now
- use SPDX identifier
changes in v2:
- prevent overflow in tmdsclk calculation
as reported by Martin Cerveny
- use unsigned long for all tmdsclk rate uses
- simplify tmds rate calculation
drivers/phy/rockchip/Kconfig | 7 + drivers/phy/rockchip/Makefile | 1 + drivers/phy/rockchip/phy-rockchip-inno-hdmi.c | 1275 +++++++++++++++++ 3 files changed, 1283 insertions(+) create mode 100644 drivers/phy/rockchip/phy-rockchip-inno-hdmi.c
drivers/phy/rockchip/Kconfig +7 -0
@@ -15,6 +15,13 @@ config PHY_ROCKCHIP_EMMC help Enable this to support the Rockchip EMMC PHY. +config PHY_ROCKCHIP_INNO_HDMI + tristate "Rockchip INNO HDMI PHY Driver" + depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF + select GENERIC_PHY + help + Enable this to support the Rockchip Innosilicon HDMI PHY. + config PHY_ROCKCHIP_INNO_USB2 tristate "Rockchip INNO USB2PHY Driver" depends on (ARCH_ROCKCHIP || COMPILE_TEST) && OF
drivers/phy/rockchip/Makefile +1 -0
@@ -1,6 +1,7 @@ # SPDX-License-Identifier: GPL-2.0 obj-$(CONFIG_PHY_ROCKCHIP_DP) += phy-rockchip-dp.o obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o +obj-$(CONFIG_PHY_ROCKCHIP_INNO_HDMI) += phy-rockchip-inno-hdmi.o obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2) += phy-rockchip-inno-usb2.o obj-$(CONFIG_PHY_ROCKCHIP_PCIE) += phy-rockchip-pcie.o obj-$(CONFIG_PHY_ROCKCHIP_TYPEC) += phy-rockchip-typec.o
drivers/phy/rockchip/phy-rockchip-inno-hdmi.c new file +1275 -0
1,275 lines not on this page · raw message
Signature · 1 line
2.17.0
Heiko Stuebner
maintainerPATCH v3 2/2 phy: add Rockchip Innosilicon hdmi phy
Hi Kishon,
Am Montag, 14. Mai 2018, 15:57:11 CEST schrieb Heiko Stuebner:
Quoted 8 lines
From: Zheng Yang <[email protected]>
Add a driver for the Innosilicon hdmi phy used on rk3228/rk3229 and rk3328 socs from Rockchip.
Signed-off-by Zheng Yang <[email protected]>Signed-off-by Heiko Stuebner <[email protected]>Tested-by Robin Murphy <[email protected]>
could you possibly take a look at this phy patch? It would be really nice to get it into 4.19 or so ;-)
Thanks
Heiko