Skip to contentSkip to conversation

imx8mqevk: readme: Put switch configuration for SD card boot

PATCH New Fabio Estevam 2 participants 3 messages May 16, 2018 – May 17, 2018 Arm i.MX and Layerscape

lore
Share & tools
lore

Fabio Estevam

author reviewer
#0 lore raw

PATCH 1/2 imx8mqevk: readme: Put switch configuration for SD card boot

From: Fabio Estevam <[email protected]>

Improve the documentation by adding the configuration of SW801 and SW802 switches for SD card boot.

Signed-off-by Fabio Estevam <[email protected]>
---
 board/freescale/imx8mqevk/readme.txt | 3 +++
 1 file changed, 3 insertions(+)
board/freescale/imx8mqevk/readme.txt +3 -0
index d50dd6e..cb7e1dc 100644
@@ -63,6 +63,9 @@ Boot the i.MX8mq EVK board
 
 To boot your newly created system:
 - insert the SD card in the SD slot of the board;
+- Configure the switches as follows:
+SW801:	ON	ON	OFF	OFF
+SW802:	ON	OFF
 - put a micro USB cable into the Debug USB Port and connect using a terminal
   emulator at 115200 bps, 8n1;
 - power on the board.
Signature · 1 line
2.7.4
author reviewer
#1 lore raw

PATCH 2/2 imx8mqevk: readme: Write the SoC name in capital letters

From: Fabio Estevam <[email protected]>

Use "i.MX8MQ" (in capital letters) for the SoC name for better readability.

Signed-off-by Fabio Estevam <[email protected]>
---
 board/freescale/imx8mqevk/readme.txt | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)
board/freescale/imx8mqevk/readme.txt +4 -4
index cb7e1dc..1840290 100644
@@ -1,8 +1,8 @@
 ***************************
-Freescale i.MX8mq EVK board
+Freescale i.MX8MQ EVK board
 ***************************
 
-This file documents the Buildroot support for the Freescale i.MX8mq
+This file documents the Buildroot support for the Freescale i.MX8MQ
 EVK board.
 
 Hardware support

@@ -14,7 +14,7 @@ support for GPU, VPU and other HW features.
 Build
 =====
 
-First, configure Buildroot for the i.MX8mq EVK board:
+First, configure Buildroot for the i.MX8MQ EVK board:
 
   make freescale_imx8mqevk_defconfig
 

@@ -58,7 +58,7 @@ command as root:
 For details about the medium image layout, see the definition in
 board/freescale/common/imx/genimage.cfg.template_imx8.
 
-Boot the i.MX8mq EVK board
+Boot the i.MX8MQ EVK board
 ==========================
 
 To boot your newly created system:
Signature · 1 line
2.7.4
#2 lore raw

PATCH 1/2 imx8mqevk: readme: Put switch configuration for SD card boot

In reply to Fabio Estevam

Hello,

Quoted 9 lines · Fabio Estevam

From: Fabio Estevam <[email protected]>

Improve the documentation by adding the configuration of SW801 and SW802 switches for SD card boot.

Signed-off-by Fabio Estevam <[email protected]>
---
 board/freescale/imx8mqevk/readme.txt | 3 +++
 1 file changed, 3 insertions(+)

Both applied to master, thanks.

Thomas

Signature · 3 lines
Thomas Petazzoni, CTO, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com