4.17-rcX delays during boot and memory mapping errors
Apologies for not having more in the way of diagnostic info.
Every one of the 4.17-rcX series has hung during boot at the point where "acpid" starts up. Beginning with -rc5, the boot actually proceeds to completion after an "uncomfortably" long delay.
Attempting to run the X11 server results in the following diagnostic output in "/var/log/Xorg.0.log":
(...)
[ 109.951] (--) Depth 24 pixmap format is 32 bpp
[ 109.951] (II) RADEON(0): [DRI2] Setup complete
[ 109.951] (II) RADEON(0): [DRI2] DRI driver: r600
[ 109.951] (II) RADEON(0): [DRI2] VDPAU driver: r600
[ 109.951] Failed to map cursor buffer memory
[ 109.951] Failed to map cursor buffer memory
[ 109.951] Failed to map cursor buffer memory
[ 109.952] Failed to map cursor buffer memory
[ 109.952] Failed to map cursor buffer memory
[ 109.952] Failed to map cursor buffer memory
[ 109.952] (II) RADEON(0): Front buffer size: 8160K
[ 109.952] (II) RADEON(0): VRAM usage limit set to 218167K
[ 109.952] (==) RADEON(0): DRI3 disabled
[ 109.952] (==) RADEON(0): Backing store enabled
[ 109.952] (II) RADEON(0): Direct rendering enabled
[ 109.952] (II) EXA(0): Driver allocated offscreen pixmaps
[ 109.952] (II) EXA(0): Driver registered support for the following
operations:
[ 109.952] (II) Solid
[ 109.952] (II) Copy
[ 109.952] (II) Composite (RENDER acceleration)
[ 109.952] (II) UploadToScreen
[ 109.952] (II) DownloadFromScreen
[ 109.952] (EE)
Fatal server error:
[ 109.952] (EE) failed to map shader -75
[ 109.952] (EE)
[ 109.952] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 109.952] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 109.952] (EE)
[ 109.971] (EE) Server terminated with error (1). Closing log file.Everything works normally with a 4.16 kernel.
--Bob
Quoted 6 lines · Bob Tracy
Every one of the 4.17-rcX series has hung during boot at the point where "acpid" starts up. Beginning with -rc5, the boot actually proceeds to completion after an "uncomfortably" long delay.
Attempting to run the X11 server results in the following diagnostic output in "
/var/log/Xorg.0.log":
v4.17-rc6 took care of the X11 server startup issue. The "uncomfortably" long delay issue persists. An observation as far as differences between 4.16 and 4.17-rc6 during startup...
In v4.16 and earlier kernels, I wouldn't see the "random: crng init done" message until moments after the system was done transitioning to multi- user mode ("login" prompt on the console). In the v4.17-rcX series, I don't see a login prompt until all the events represented in the "dmesg" output below have occurred:
(...)
[ 7.314001] NET: Registered protocol family 10 [ 7.315781] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 7.317359] Segment Routing with IPv6 [ 8.667444] NET: Registered protocol family 17 [ 9.130872] e1000e: eth0 NIC Link is Up 10 Mbps Half Duplex, Flow Control: None [ 9.131839] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO [ 9.136947] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 78.567150] random: crng init done [ 102.974609] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 102.982063] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 102.983716] r8152 2-1.5:1.0 eth1: carrier on
(end of dmesg output)
As far as what I see on the console during bootup, I see the "IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready" message, then the system "hangs" until the "random: crng init done" message appears. Then "acpid" startup and other events proceed normally.
Any idea what's going on here?
--Bob