regulator: arizona-ldo1: Use correct device to get enable GPIO
PATCH 1/1 regulator: arizona-ldo1: Use correct device to get enable GPIO
Currently the enable GPIO is being looked up on the regulator device itself but that does not have its own DT node, this causes the lookup to fail and the regulator not to get its GPIO. The DT node is shared across the whole MFD and as such the lookup needs to happen on that parent device. Moving the lookup to the parent device also means devres can no longer be used as the life time would attach to the wrong device.
---
Apologies for missing this again, we should have caught this in our testing and thanks for reporting it.
Thanks,
Charles
drivers/regulator/arizona-ldo1.c | 27 ++++++++++++++++++++++++--- 1 file changed, 24 insertions(+), 3 deletions(-)
drivers/regulator/arizona-ldo1.c +24 -3
@@ -36,6 +36,8 @@ struct arizona_ldo1 {struct regulator_consumer_supply supply;struct regulator_init_data init_data; + +struct gpio_desc *ena_gpiod; }; static int arizona_ldo1_hc_list_voltage(struct regulator_dev *rdev,
@@ -253,12 +255,17 @@ static int arizona_ldo1_common_init(struct platform_device *pdev, } } -/* We assume that high output = regulator off */ - config.ena_gpiod =devm_gpiod_get_optional (&pdev->dev,"wlf,ldoena" , -GPIOD_OUT_HIGH ); +/* We assume that high output = regulator off +* Don't use devm, since we need to get against the parent device +* so clean up would happen at the wrong time +*/ + config.ena_gpiod =gpiod_get_optional (parent_dev,"wlf,ldoena" , +GPIOD_OUT_HIGH );if (IS_ERR (config.ena_gpiod))return PTR_ERR (config.ena_gpiod); + ldo1->ena_gpiod = config.ena_gpiod; +if (pdata->init_data) config.init_data = pdata->init_data;else
@@ -276,6 +283,9 @@ static int arizona_ldo1_common_init(struct platform_device *pdev,of_node_put (config.of_node);if (IS_ERR (ldo1->regulator)) { +if (config.ena_gpiod) +gpiod_put (config.ena_gpiod); + ret =PTR_ERR (ldo1->regulator);dev_err (&pdev->dev,"Failed to register LDO1 supply: %d\n" , ret);
@@ -334,8 +344,19 @@ static int arizona_ldo1_probe(struct platform_device *pdev)return ret; } +static int arizona_ldo1_remove (struct platform_device *pdev) +{ +struct arizona_ldo1 *ldo1 =platform_get_drvdata (pdev); + +if (ldo1->ena_gpiod) +gpiod_put (ldo1->ena_gpiod); + +return 0 ; +} +static struct platform_driver arizona_ldo1_driver = { .probe = arizona_ldo1_probe, + .remove = arizona_ldo1_remove, .driver = { .name ="arizona-ldo1" , },
Signature · 1 line
2.11.0
Quoted 11 lines · Charles Keepax
Currently the enable GPIO is being looked up on the regulator device itself but that does not have its own DT node, this causes the lookup to fail and the regulator not to get its GPIO. The DT node is shared across the whole MFD and as such the lookup needs to happen on that parent device. Moving the lookup to the parent device also means devres can no longer be used as the life time would attach to the wrong device.
Fixes e1739e86f0cb ("regulator: arizona-ldo1: Look up a descriptor and pass to the core")Reported-by Matthias Reichl <[email protected]>Signed-off-by Charles Keepax <[email protected]>
Quoted 2 lines
Apologies for missing this again, we should have caught this in our testing and thanks for reporting it.
No problem, and thank you a lot for the quick fix!
During testing I noticed another minor change introduced by commit e1739e86f0cb, see comment inline below.
Quoted 23 lines
Thanks,
Charlesdrivers/regulator/arizona-ldo1.c | 27 ++++++++++++++++++++++++--- 1 file changed, 24 insertions(+), 3 deletions(-)drivers/regulator/arizona-ldo1.c +2
-0@@ -36,6 +36,8 @@ struct arizona_ldo1 {struct regulator_consumer_supply supply;struct regulator_init_data init_data; + +struct gpio_desc *ena_gpiod; }; static int arizona_ldo1_hc_list_voltage(struct regulator_dev *rdev,@@ -253,12 +255,17 @@ static int arizona_ldo1_common_init(struct platform_device *pdev, } }
drivers/regulator/arizona-ldo1.c static int arizona_ldo1_common_init(struct platform_device *pdev, · line 263
Quoted 10 lines
drivers/regulator/arizona-ldo1.c +6
-3-/* We assume that high output = regulator off */ - config.ena_gpiod =devm_gpiod_get_optional (&pdev->dev,"wlf,ldoena" , -GPIOD_OUT_HIGH ); +/* We assume that high output = regulator off +* Don't use devm, since we need to get against the parent device +* so clean up would happen at the wrong time +*/ + config.ena_gpiod =gpiod_get_optional (parent_dev,"wlf,ldoena" , +GPIOD_OUT_HIGH );
The WM5102 datasheet lists LDOENA as an active-high input, so GPIOD_OUT_HIGH causes arizona-ldo1 to start up enabled. Not sure about the other devices from the Arizona family.
I did some tests monitoring ldoena and reset gpios with my scope:
With commit e1739e86f0cb reverted ldoena changes from low to high about 1.6ms before reset changes from low to high.
With your patch ldoena goes high about 11.5ms before reset goes high.
With your patch and GPIOD_OUT_HIGH changed to GPIOD_OUT_LOW the delay is again about 1.6ms.
So I guess it'd be better to adjust the comment and change to gpiod flag to GPIOD_OUT_LOW.
so long,
Hias
Quoted 41 lines
drivers/regulator/arizona-ldo1.c +16
-0if (IS_ERR (config.ena_gpiod))return PTR_ERR (config.ena_gpiod); + ldo1->ena_gpiod = config.ena_gpiod; +if (pdata->init_data) config.init_data = pdata->init_data;else @@ -276,6 +283,9 @@ static int arizona_ldo1_common_init(struct platform_device *pdev,of_node_put (config.of_node);if (IS_ERR (ldo1->regulator)) { +if (config.ena_gpiod) +gpiod_put (config.ena_gpiod); + ret =PTR_ERR (ldo1->regulator);dev_err (&pdev->dev,"Failed to register LDO1 supply: %d\n" , ret);@@ -334,8 +344,19 @@ static int arizona_ldo1_probe(struct platform_device *pdev)return ret; } +static int arizona_ldo1_remove (struct platform_device *pdev) +{ +struct arizona_ldo1 *ldo1 =platform_get_drvdata (pdev); + +if (ldo1->ena_gpiod) +gpiod_put (ldo1->ena_gpiod); + +return 0 ; +} +static struct platform_driver arizona_ldo1_driver = { .probe = arizona_ldo1_probe, + .remove = arizona_ldo1_remove, .driver = { .name ="arizona-ldo1" , },Signature · 1 line
2.11.0
Quoted 8 lines · Matthias Reichl
drivers/regulator/arizona-ldo1.c static int arizona_ldo1_common_init(struct platform_device *pdev, · line 263
Quoted 2 lines · Charles Keepax
drivers/regulator/arizona-ldo1.c +2
-0+ config.ena_gpiod =gpiod_get_optional (parent_dev,"wlf,ldoena" , +GPIOD_OUT_HIGH );The WM5102 datasheet lists LDOENA as an active-high input, so
GPIOD_OUT_HIGHcauses arizona-ldo1 to start up enabled. Not sure about the other devices from the Arizona family.
Yeah all active high.
Quoted 5 lines
I did some tests monitoring ldoena and reset gpios with my scope:
With commit
e1739e86f0cbreverted ldoena changes from low to high about 1.6ms before reset changes from low to high.
Quoted 7 lines
With your patch ldoena goes high about 11.5ms before reset goes high.
With your patch and
GPIOD_OUT_HIGHchanged toGPIOD_OUT_LOWthe delay is again about 1.6ms.So I guess it'd be better to adjust the comment and change to gpiod flag to
GPIOD_OUT_LOW.
Yeah I am inclined to agree would be better to keep the behaviour the same as it has always been given these parts are fairly mature I will respin the patch to add that change too.
Thanks,
Charles