Skip to contentSkip to conversation

USB: serial: cp210x: make line-speed quantisation data driven

PATCH New Johan Hovold 1 participant 1 message Jul 5, 2018

Subsystems (2)
USB USB serial
lore
Share & tools
lore

Johan Hovold

author maintainer
#0 lore raw

PATCH 1/2 USB: serial: cp210x: make line-speed quantisation data driven

Older cp210x devices only support a fixed set of line speeds to which a requested speed is mapped. Reimplement this mapping using a table instead of a long if-else construct.

Signed-off-by Johan Hovold <[email protected]>
---
 drivers/usb/serial/cp210x.c | 99 +++++++++++++++++++++----------------
 1 file changed, 56 insertions(+), 43 deletions(-)
drivers/usb/serial/cp210x.c +56 -43
index 626a29d9aa58..e1a4d4b3d3aa 100644
@@ -767,48 +767,6 @@ static int cp210x_get_line_ctl(struct usb_serial_port *port, u16 *ctl)
 	return 0;
 }
 
-/*
- * cp210x_quantise_baudrate
- * Quantises the baud rate as per AN205 Table 1
- */
-static unsigned int cp210x_quantise_baudrate(unsigned int baud)
-{
-	if (baud <= 300)
-		baud = 300;
-	else if (baud <= 600)      baud = 600;
-	else if (baud <= 1200)     baud = 1200;
-	else if (baud <= 1800)     baud = 1800;
-	else if (baud <= 2400)     baud = 2400;
-	else if (baud <= 4000)     baud = 4000;
-	else if (baud <= 4803)     baud = 4800;
-	else if (baud <= 7207)     baud = 7200;
-	else if (baud <= 9612)     baud = 9600;
-	else if (baud <= 14428)    baud = 14400;
-	else if (baud <= 16062)    baud = 16000;
-	else if (baud <= 19250)    baud = 19200;
-	else if (baud <= 28912)    baud = 28800;
-	else if (baud <= 38601)    baud = 38400;
-	else if (baud <= 51558)    baud = 51200;
-	else if (baud <= 56280)    baud = 56000;
-	else if (baud <= 58053)    baud = 57600;
-	else if (baud <= 64111)    baud = 64000;
-	else if (baud <= 77608)    baud = 76800;
-	else if (baud <= 117028)   baud = 115200;
-	else if (baud <= 129347)   baud = 128000;
-	else if (baud <= 156868)   baud = 153600;
-	else if (baud <= 237832)   baud = 230400;
-	else if (baud <= 254234)   baud = 250000;
-	else if (baud <= 273066)   baud = 256000;
-	else if (baud <= 491520)   baud = 460800;
-	else if (baud <= 567138)   baud = 500000;
-	else if (baud <= 670254)   baud = 576000;
-	else if (baud < 1000000)
-		baud = 921600;
-	else if (baud > 2000000)
-		baud = 2000000;
-	return baud;
-}
-
 static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port)
 {
 	int result;

@@ -1028,6 +986,58 @@ static void cp210x_get_termios_port(struct usb_serial_port *port,
 	*cflagp = cflag;
 }
 
+struct cp210x_rate {
+	speed_t rate;
+	speed_t high;
+};
+
+static const struct cp210x_rate cp210x_an205_table1[] = {
+	{ 300, 300 },
+	{ 600, 600 },
+	{ 1200, 1200 },
+	{ 1800, 1800 },
+	{ 2400, 2400 },
+	{ 4000, 4000 },
+	{ 4800, 4803 },
+	{ 7200, 7207 },
+	{ 9600, 9612 },
+	{ 14400, 14428 },
+	{ 16000, 16062 },
+	{ 19200, 19250 },
+	{ 28800, 28912 },
+	{ 38400, 38601 },
+	{ 51200, 51558 },
+	{ 56000, 56280 },
+	{ 57600, 58053 },
+	{ 64000, 64111 },
+	{ 76800, 77608 },
+	{ 115200, 117028 },
+	{ 128000, 129347 },
+	{ 153600, 156868 },
+	{ 230400, 237832 },
+	{ 250000, 254234 },
+	{ 256000, 273066 },
+	{ 460800, 491520 },
+	{ 500000, 567138 },
+	{ 576000, 670254 },
+	{ 921600, UINT_MAX }
+};
+
+/*
+ * Quantises the baud rate as per AN205 Table 1
+ */
+static speed_t cp210x_get_an205_rate(speed_t baud)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(cp210x_an205_table1); ++i) {
+		if (baud <= cp210x_an205_table1[i].high)
+			break;
+	}
+
+	return cp210x_an205_table1[i].rate;
+}
+
 /*
  * CP2101 supports the following baud rates:
  *

@@ -1066,7 +1076,10 @@ static void cp210x_change_speed(struct tty_struct *tty,
 	 *
 	 * NOTE: B0 is not implemented.
 	 */
-	baud = cp210x_quantise_baudrate(baud);
+	if (baud < 1000000)
+		baud = cp210x_get_an205_rate(baud);
+	else if (baud > 2000000)
+		baud = 2000000;
 
 	dev_dbg(&port->dev, "%s - setting baud rate to %u\n", __func__, baud);
 	if (cp210x_write_u32_reg(port, CP210X_SET_BAUDRATE, baud)) {