Skip to contentSkip to conversation

add support to non-uniform SFDP SPI NOR flash memories

PATCH Superseded Tudor Ambarus 1 participant 6 messages Jul 12, 2018 – Aug 20, 2018

Subsystems (2)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover add support to non-uniform SFDP SPI NOR flash memories

Backward compatibility test done on mx25l3273fm2i-08g. Non-uniform erase test done on sst26vf064b-104i/sn.

Note that in order to do the non-uniform test on the aforementioned memory you'll have to force the spi_nor_has_uniform_erase() to return false, because the erase map is tuned to come back to the uniform case. Also, you'll have to unlock the global protection on the flash. There was an attempt to unlock this protection, but for whatever reason the patch was not taken:
https://patchwork.ozlabs.org/patch/544270/. I'm taking care of the global protection lock on sst26vf064b-104i/sn, I will submit a patch soon.

Changes in v2:
- add JESD216B SFDP optional parser: Sector Map Parameter Table parser and 4-byte Address Instruction Table parser (patch 2/3 and patch 3/3).
- fix condition on finding erase regions
- fix the list command adding
- write_enable(nor); before erasing the sectors
- As Boris suggested, remove likely() because it doesn't make any difference given the time it takes to actually erase the block.
- save the Erase Types from bfpt, to determine the Erase Type sizes. Sort all the map's Erase Types in ascending order with the smallest erase size being the first member in the erase_type array. Sort Erase Type mask in regions. We sort the Erase Type by size, at init, in order to speed up the process of finding the best erase command at run-time.
- spi_nor_select_erase(): pass directly info->sector_size instead of the whole flash_info structure in order to simplify the code.
- keep the same convention as most flashes, and order erase types by size with the smallest Erase Type size starting at index 0/ BIT(0).
- return unused function: spi_nor_region_mark_end().
- fix return value of spi_nor_has_uniform_erase().
- remove setting of mtd->erasesize and nor->erase_opcode when parsing the Basic Flash Parameter Table. mtd->erasesize was set to the maximum supported Erase Type size, without verifying if that Erase Type can erase the entire flash. mtd->erasesize is now set just in spi_nor_select_erase(), after we find which Erase Types are supported in the uniform case.

Changes in v1 or what I've done on top of Cyrille's work (https://lkml.org/lkml/2017/4/15/70):
- minimize the amount of erase() calls by using the best sequence of erase
type commands depending on alignment.
- build the list of best fitted erase commands to be executed once we
validate that the erase can be performed.
- add improvements on how the erase map is handled. The regions are
consecutive in the address space, walk through the regions incrementally.
- speed up finding the best erase type command. Order erase types by
size, iterate them from the biggest to the smallest and stop when best
fitted command is found.
- determine at init if there are erase types that can erase the entire
memory
- fix support for overlaid regions.

Cyrille Pitchen (1):
mtd: spi-nor: parse SFDP 4-byte Address Instruction Table

Tudor Ambarus (2):
mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
mtd: spi-nor: parse SFDP Sector Map Parameter Table

 drivers/mtd/spi-nor/spi-nor.c | 892 +++++++++++++++++++++++++++++++++++++++---
 include/linux/mtd/spi-nor.h   | 120 ++++++
 2 files changed, 954 insertions(+), 58 deletions(-)
Signature · 1 line
2.9.4
#1 lore raw

PATCH v2 1/3 mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories

Based on Cyrille Pitchen's patch https://lkml.org/lkml/2017/3/22/935.

This patch is a transitional patch in introducing the support of SFDP SPI memories with non-uniform erase sizes like Spansion s25fs512s. Non-uniform erase maps will be used later when initialized based on the SFDP data.

Introduce the memory erase map which splits the memory array into one or many erase regions. Each erase region supports up to 4 erase types, as defined by the JEDEC JESD216B (SFDP) specification.

To be backward compatible, the erase map of uniform SPI NOR flash memories is initialized so it contains only one erase region and this erase region supports only one erase command. Hence a single size is used to erase any sector/block of the memory.

Besides, since the algorithm used to erase sectors on non-uniform SPI NOR flash memories is quite expensive, when possible, the erase map is tuned to come back to the uniform case.

The 'erase with the best command, move forward and repeat' approach was suggested by Cristian Birsan in a brainstorm session, so:

---
 drivers/mtd/spi-nor/spi-nor.c | 475 ++++++++++++++++++++++++++++++++++++++----
 include/linux/mtd/spi-nor.h   | 109 ++++++++++
 2 files changed, 542 insertions(+), 42 deletions(-)
drivers/mtd/spi-nor/spi-nor.c +433 -42
index d9c368c..899b8c1 100644
@@ -18,6 +18,7 @@
 #include <linux/math64.h>
 #include <linux/sizes.h>
 #include <linux/slab.h>
+#include <linux/sort.h>
 
 #include <linux/mtd/mtd.h>
 #include <linux/of_platform.h>
@@ -260,6 +261,18 @@ static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
 	nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode);
 	nor->program_opcode = spi_nor_convert_3to4_program(nor->program_opcode);
 	nor->erase_opcode = spi_nor_convert_3to4_erase(nor->erase_opcode);
+
+	if (!spi_nor_has_uniform_erase(nor)) {
+		struct spi_nor_erase_map *map = &nor->erase_map;
+		struct spi_nor_erase_type *erase;
+		int i;
+
+		for (i = 0; i < SNOR_ERASE_TYPE_MAX; i++) {
+			erase = &map->erase_type[i];
+			erase->opcode =
+				spi_nor_convert_3to4_erase(erase->opcode);
+		}
+	}
 }
 
 /* Enable/disable 4-byte addressing mode. */
@@ -497,6 +510,206 @@ static int spi_nor_erase_sector(struct spi_nor *nor, u32 addr)
 	return nor->write_reg(nor, nor->erase_opcode, buf, nor->addr_width);
 }
 
+/* JEDEC JESD216B Standard imposes erase sizes to be power of 2. */
+static inline u64
+spi_nor_div_by_erase_size(const struct spi_nor_erase_type *erase,
+			  u64 dividend, u32 *remainder)
+{
+	*remainder = (u32)dividend & erase->size_mask;
+	return dividend >> erase->size_shift;
+}
+
+static const struct spi_nor_erase_type *
+spi_nor_find_best_erase_type(const struct spi_nor_erase_map *map,
+			     const struct spi_nor_erase_region *region,
+			     u64 addr, u32 len)
+{
+	const struct spi_nor_erase_type *erase;
+	u32 rem;
+	int i;
+	u8 erase_mask = region->offset & SNOR_ERASE_TYPE_MASK;
+
+	/*
+	 * Erase types are ordered by size, with the biggest erase type at
+	 * index 0.
+	 */
+	for (i = SNOR_ERASE_TYPE_MAX - 1; i >= 0; i--) {
+		/* Does the erase region support the tested erase type? */
+		if (!(erase_mask & BIT(i)))
+			continue;
+
+		erase = &map->erase_type[i];
+
+		/* Don't erase more than what the user has asked for. */
+		if (erase->size > len)
+			continue;
+
+		/* Alignment is not mandatory for overlaid regions */
+		if (region->offset & SNOR_OVERLAID_REGION)
+			return erase;
+
+		spi_nor_div_by_erase_size(erase, addr, &rem);
+		if (rem)
+			continue;
+		else
+			return erase;
+	}
+
+	return NULL;
+}
+
+static struct spi_nor_erase_region *
+spi_nor_region_next(struct spi_nor_erase_region *region)
+{
+	if (spi_nor_region_is_last(region))
+		return NULL;
+	return ++region;
+}
+
+static struct spi_nor_erase_region *
+spi_nor_find_erase_region(const struct spi_nor_erase_map *map, u64 addr,
+			  u32 len)
+{
+	struct spi_nor_erase_region *region = map->regions;
+	u64 region_start = region->offset & ~SNOR_ERASE_FLAGS_MASK;
+	u64 region_end = region_start + region->size;
+
+	while (addr < region_start || addr >= region_end) {
+		region = spi_nor_region_next(region);
+		if (!region)
+			return ERR_PTR(-EINVAL);
+
+		region_start = region->offset & ~SNOR_ERASE_FLAGS_MASK;
+		region_end = region_start + region->size;
+	}
+
+	return region;
+}
+
+static struct spi_nor_erase_command *
+spi_nor_init_erase_cmd(const struct spi_nor_erase_region *region,
+		       const struct spi_nor_erase_type *erase, u64 addr)
+{
+	struct spi_nor_erase_command *cmd;
+
+	cmd = kmalloc(sizeof(*cmd), GFP_KERNEL);
+	if (!cmd)
+		return ERR_PTR(-ENOMEM);
+
+	INIT_LIST_HEAD(&cmd->list);
+	cmd->opcode = erase->opcode;
+	cmd->count = 1;
+
+	if (region->offset & SNOR_OVERLAID_REGION)
+		cmd->size = region->size;
+	else
+		cmd->size = erase->size;
+
+	return cmd;
+}
+
+static void spi_nor_destroy_erase_cmd_list(struct list_head *erase_list)
+{
+	struct spi_nor_erase_command *cmd, *next;
+
+	list_for_each_entry_safe(cmd, next, erase_list, list) {
+		list_del(&cmd->list);
+		kfree(cmd);
+	}
+}
+
+static int spi_nor_init_erase_cmd_list(struct spi_nor *nor,
+				       struct list_head *erase_list,
+				       u64 addr, u32 len)
+{
+	const struct spi_nor_erase_map *map = &nor->erase_map;
+	const struct spi_nor_erase_type *erase, *prev_erase = NULL;
+	struct spi_nor_erase_region *region;
+	struct spi_nor_erase_command *cmd = NULL;
+	u64 region_end;
+	int ret = -EINVAL;
+
+	region = spi_nor_find_erase_region(map, addr, len);
+	if (IS_ERR(region))
+		return PTR_ERR(region);
+
+	region_end = spi_nor_region_end(region);
+
+	while (len) {
+		erase = spi_nor_find_best_erase_type(map, region, addr, len);
+		if (!erase)
+			goto destroy_erase_cmd_list;
+
+		if (prev_erase != erase ||
+		    region->offset & SNOR_OVERLAID_REGION) {
+			cmd = spi_nor_init_erase_cmd(region, erase, addr);
+			if (IS_ERR(cmd)) {
+				ret = PTR_ERR(cmd);
+				goto destroy_erase_cmd_list;
+			}
+
+			list_add_tail(&cmd->list, erase_list);
+		} else {
+			cmd->count++;
+		}
+
+		addr += cmd->size;
+		len -= cmd->size;
+
+		if (len && addr >= region_end) {
+			region = spi_nor_region_next(region);
+			if (!region)
+				goto destroy_erase_cmd_list;
+			region_end = spi_nor_region_end(region);
+		}
+
+		prev_erase = erase;
+	}
+
+	return 0;
+
+destroy_erase_cmd_list:
+	spi_nor_destroy_erase_cmd_list(erase_list);
+	return ret;
+}
+
+static int spi_nor_erase_multi_sectors(struct spi_nor *nor, u64 addr, u32 len)
+{
+	LIST_HEAD(erase_list);
+	struct spi_nor_erase_command *cmd, *next;
+	int ret;
+
+	ret = spi_nor_init_erase_cmd_list(nor, &erase_list, addr, len);
+	if (ret)
+		return ret;
+
+	list_for_each_entry_safe(cmd, next, &erase_list, list) {
+		nor->erase_opcode = cmd->opcode;
+		while (cmd->count) {
+			write_enable(nor);
+
+			ret = spi_nor_erase_sector(nor, addr);
+			if (ret)
+				goto destroy_erase_cmd_list;
+
+			addr += cmd->size;
+			cmd->count--;
+
+			ret = spi_nor_wait_till_ready(nor);
+			if (ret)
+				goto destroy_erase_cmd_list;
+		}
+		list_del(&cmd->list);
+		kfree(cmd);
+	}
+
+	return 0;
+
+destroy_erase_cmd_list:
+	spi_nor_destroy_erase_cmd_list(&erase_list);
+	return ret;
+}
+
 /*
  * Erase an address range on the nor chip.  The address range may extend
  * one or more erase sectors.  Return an error is there is a problem erasing.
@@ -511,9 +724,11 @@ static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
 	dev_dbg(nor->dev, "at 0x%llx, len %lld\n", (long long)instr->addr,
 			(long long)instr->len);
 
-	div_u64_rem(instr->len, mtd->erasesize, &rem);
-	if (rem)
-		return -EINVAL;
+	if (spi_nor_has_uniform_erase(nor)) {
+		div_u64_rem(instr->len, mtd->erasesize, &rem);
+		if (rem)
+			return -EINVAL;
+	}
 
 	addr = instr->addr;
 	len = instr->len;
@@ -552,7 +767,7 @@ static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
 	 */
 
 	/* "sector"-at-a-time erase */
-	} else {
+	} else if (spi_nor_has_uniform_erase(nor)) {
 		while (len) {
 			write_enable(nor);
 
@@ -567,6 +782,12 @@ static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
 			if (ret)
 				goto erase_err;
 		}
+
+	/* erase multiple sectors */
+	} else {
+		ret = spi_nor_erase_multi_sectors(nor, addr, len);
+		if (ret)
+			goto erase_err;
 	}
 
 	write_disable(nor);
@@ -2165,6 +2386,83 @@ static const struct sfdp_bfpt_erase sfdp_bfpt_erases[] = {
 
 static int spi_nor_hwcaps_read2cmd(u32 hwcaps);
 
+/* JEDEC JESD216B Standard imposes erase sizes to be power of 2. */
+static inline void
+spi_nor_set_erase_type(struct spi_nor_erase_type *erase,  u32 size, u8 opcode)
+{
+	erase->size = size;
+	erase->opcode = opcode;
+	erase->size_shift = ffs(erase->size) - 1;
+	erase->size_mask = (1 << erase->size_shift) - 1;
+}
+
+static inline void
+spi_nor_set_erase_settings_from_bfpt(struct spi_nor_erase_type *erase,
+				     u32 size, u8 opcode, u8 i)
+{
+	/*
+	 * The supported Erase Types will be sorted at init in ascending order,
+	 * with the smallest Erase Type size being the first member
+	 * in the erase_type array of the spi_nor_erase_map structure.
+	 * Save the Erase Type index as sorted in the Basic Flash Parameter
+	 * Table since it will be used later on to synchronize with the
+	 * supported Erase Types defined in SFDP optional tables.
+	 */
+	erase->idx = i;
+	spi_nor_set_erase_type(erase, size, opcode);
+}
+
+static int spi_nor_cmp_erase_type(const void *a, const void *b)
+{
+	const struct spi_nor_erase_type *erase1 = a;
+	const struct spi_nor_erase_type *erase2 = b;
+
+	return erase1->size - erase2->size;
+}
+
+static void spi_nor_regions_sort_erase_types(struct spi_nor_erase_map *map)
+{
+	struct spi_nor_erase_region *region = map->regions;
+	struct spi_nor_erase_type *erase_type = map->erase_type;
+	int i;
+	u8 region_erase_mask, ordered_erase_mask;
+
+	/*
+	 * Sort each region's Erase Types in ascending order with the smallest
+	 * Erase Type size starting at BIT(0).
+	 */
+	while (region) {
+		region_erase_mask = region->offset & SNOR_ERASE_TYPE_MASK;
+
+		/*
+		 * The region's erase mask indicates which erase types are
+		 * supported from the erase types defined in the map.
+		 */
+		ordered_erase_mask = 0;
+		for (i = 0; i < SNOR_ERASE_TYPE_MAX; i++)
+			if (erase_type[i].size &&
+			    region_erase_mask & BIT(erase_type[i].idx))
+				ordered_erase_mask |= BIT(i);
+
+		/* Overwrite erase mask. */
+		region->offset = (region->offset & ~SNOR_ERASE_TYPE_MASK) |
+				 ordered_erase_mask;
+
+		region = spi_nor_region_next(region);
+	}
+}
+
+static inline void
+spi_nor_init_uniform_erase_map(struct spi_nor_erase_map *map,
+			       u8 erase_mask, u64 flash_size)
+{
+	map->uniform_region.offset = SNOR_ERASE_FLAGS_OFFSET(erase_mask, 1, 0,
+							     0);
+	map->uniform_region.size = flash_size;
+	map->regions = &map->uniform_region;
+	map->uniform_erase_type = erase_mask;
+}
+
 /**
  * spi_nor_parse_bfpt() - read and parse the Basic Flash Parameter Table.
  * @nor:		pointer to a 'struct spi_nor'
@@ -2199,12 +2497,14 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
 			      const struct sfdp_parameter_header *bfpt_header,
 			      struct spi_nor_flash_parameter *params)
 {
-	struct mtd_info *mtd = &nor->mtd;
+	struct spi_nor_erase_map *map = &nor->erase_map;
+	struct spi_nor_erase_type *erase_type = map->erase_type;
 	struct sfdp_bfpt bfpt;
 	size_t len;
 	int i, cmd, err;
 	u32 addr;
 	u16 half;
+	u8 erase_mask;
 
 	/* JESD216 Basic Flash Parameter Table length is at least 9 DWORDs. */
 	if (bfpt_header->length < BFPT_DWORD_MAX_JESD216)
@@ -2273,7 +2573,12 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
 		spi_nor_set_read_settings_from_bfpt(read, half, rd->proto);
 	}
 
-	/* Sector Erase settings. */
+	/*
+	 * Sector Erase settings. Reinitialize the uniform erase map using the
+	 * Erase Types defined in the bfpt table.
+	 */
+	erase_mask = 0;
+	memset(&nor->erase_map, 0, sizeof(nor->erase_map));
 	for (i = 0; i < ARRAY_SIZE(sfdp_bfpt_erases); i++) {
 		const struct sfdp_bfpt_erase *er = &sfdp_bfpt_erases[i];
 		u32 erasesize;
@@ -2288,18 +2593,18 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
 
 		erasesize = 1U << erasesize;
 		opcode = (half >> 8) & 0xff;
-#ifdef CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
-		if (erasesize == SZ_4K) {
-			nor->erase_opcode = opcode;
-			mtd->erasesize = erasesize;
-			break;
-		}
-#endif
-		if (!mtd->erasesize || mtd->erasesize < erasesize) {
-			nor->erase_opcode = opcode;
-			mtd->erasesize = erasesize;
-		}
+		erase_mask |= BIT(i);
+		spi_nor_set_erase_settings_from_bfpt(&erase_type[i], erasesize,
+						     opcode, i);
 	}
+	spi_nor_init_uniform_erase_map(map, erase_mask, params->size);
+	/*
+	 * Sort all the map's Erase Types in ascending order with the smallest
+	 * erase size being the first member in the erase_type array.
+	 */
+	sort(erase_type, SNOR_ERASE_TYPE_MAX, sizeof(erase_type[0]),
+	     spi_nor_cmp_erase_type, NULL);
+	spi_nor_regions_sort_erase_types(map);
 
 	/* Stop here if not JESD216 rev A or later. */
 	if (bfpt_header->length < BFPT_DWORD_MAX)
@@ -2455,6 +2760,9 @@ static int spi_nor_init_params(struct spi_nor *nor,
 			       const struct flash_info *info,
 			       struct spi_nor_flash_parameter *params)
 {
+	struct spi_nor_erase_map *map = &nor->erase_map;
+	u8 i, erase_mask;
+
 	/* Set legacy flash parameters as default. */
 	memset(params, 0, sizeof(*params));
 
@@ -2494,6 +2802,28 @@ static int spi_nor_init_params(struct spi_nor *nor,
 	spi_nor_set_pp_settings(&params->page_programs[SNOR_CMD_PP],
 				SPINOR_OP_PP, SNOR_PROTO_1_1_1);
 
+	/*
+	 * Sector Erase settings. Sort Erase Types in ascending order, with the
+	 * smallest erase size starting at BIT(0).
+	 */
+	erase_mask = 0;
+	i = 0;
+	if (info->flags & SECT_4K_PMC) {
+		erase_mask |= BIT(i);
+		spi_nor_set_erase_type(&map->erase_type[i], 4096u,
+				       SPINOR_OP_BE_4K_PMC);
+		i++;
+	} else if (info->flags & SECT_4K) {
+		erase_mask |= BIT(i);
+		spi_nor_set_erase_type(&map->erase_type[i], 4096u,
+				       SPINOR_OP_BE_4K);
+		i++;
+	}
+	erase_mask |= BIT(i);
+	spi_nor_set_erase_type(&map->erase_type[i], info->sector_size,
+			       SPINOR_OP_SE);
+	spi_nor_init_uniform_erase_map(map, erase_mask, params->size);
+
 	/* Select the procedure to set the Quad Enable bit. */
 	if (params->hwcaps.mask & (SNOR_HWCAPS_READ_QUAD |
 				   SNOR_HWCAPS_PP_QUAD)) {
@@ -2521,20 +2851,20 @@ static int spi_nor_init_params(struct spi_nor *nor,
 			params->quad_enable = info->quad_enable;
 	}
 
-	/* Override the parameters with data read from SFDP tables. */
-	nor->addr_width = 0;
-	nor->mtd.erasesize = 0;
 	if ((info->flags & (SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)) &&
 	    !(info->flags & SPI_NOR_SKIP_SFDP)) {
 		struct spi_nor_flash_parameter sfdp_params;
+		struct spi_nor_erase_map prev_map;
 
 		memcpy(&sfdp_params, params, sizeof(sfdp_params));
-		if (spi_nor_parse_sfdp(nor, &sfdp_params)) {
-			nor->addr_width = 0;
-			nor->mtd.erasesize = 0;
-		} else {
+		memcpy(&prev_map, &nor->erase_map, sizeof(prev_map));
+
+		if (spi_nor_parse_sfdp(nor, &sfdp_params))
+			/* restore previous erase map */
+			memcpy(&nor->erase_map, &prev_map,
+			       sizeof(nor->erase_map));
+		else
 			memcpy(params, &sfdp_params, sizeof(*params));
-		}
 	}
 
 	return 0;
@@ -2643,29 +2973,90 @@ static int spi_nor_select_pp(struct spi_nor *nor,
 	return 0;
 }
 
-static int spi_nor_select_erase(struct spi_nor *nor,
-				const struct flash_info *info)
+static const struct spi_nor_erase_type *
+spi_nor_select_uniform_erase(struct spi_nor_erase_map *map,
+			     const u32 sector_size)
 {
-	struct mtd_info *mtd = &nor->mtd;
+	const struct spi_nor_erase_type *tested_erase, *erase = NULL;
+	int i;
+	u8 uniform_erase_type = map->uniform_erase_type;
 
-	/* Do nothing if already configured from SFDP. */
-	if (mtd->erasesize)
-		return 0;
+	for (i = SNOR_ERASE_TYPE_MAX - 1; i >= 0; i--) {
+		if (!(uniform_erase_type & BIT(i)))
+			continue;
+
+		tested_erase = &map->erase_type[i];
+
+		/*
+		 * If the current erase size is the one, stop here:
+		 * we have found the right uniform Sector Erase command.
+		 */
+		if (tested_erase->size == sector_size) {
+			erase = tested_erase;
+			break;
+		}
+
+		/*
+		 * Otherwise, the current erase size is still a valid canditate.
+		 * Select the biggest valid candidate.
+		 */
+		if (!erase && tested_erase->size)
+			erase = tested_erase;
+	}
 
+	if (!erase)
+		return ERR_PTR(-EINVAL);
+
+	/* Disable all other Sector Erase commands. */
+	map->uniform_erase_type &= ~SNOR_ERASE_TYPE_MASK;
+	map->uniform_erase_type |= BIT(erase - map->erase_type);
+	return erase;
+}
+
+static int spi_nor_select_erase(struct spi_nor *nor, u32 sector_size)
+{
+	struct spi_nor_erase_map *map = &nor->erase_map;
+	const struct spi_nor_erase_type *erase = NULL;
+	struct mtd_info *mtd = &nor->mtd;
+	int i;
+
+	/*
+	 * The previous implementation handling Sector Erase commands assumed
+	 * that the SPI flash memory has an uniform layout then used only one
+	 * of the supported erase sizes for all Sector Erase commands.
+	 * So to be backward compatible, the new implementation also tries to
+	 * manage the SPI flash memory as uniform with a single erase sector
+	 * size, when possible.
+	 */
 #ifdef CONFIG_MTD_SPI_NOR_USE_4K_SECTORS
 	/* prefer "small sector" erase if possible */
-	if (info->flags & SECT_4K) {
-		nor->erase_opcode = SPINOR_OP_BE_4K;
-		mtd->erasesize = 4096;
-	} else if (info->flags & SECT_4K_PMC) {
-		nor->erase_opcode = SPINOR_OP_BE_4K_PMC;
-		mtd->erasesize = 4096;
-	} else
+	sector_size = 4096u;
 #endif
-	{
-		nor->erase_opcode = SPINOR_OP_SE;
-		mtd->erasesize = info->sector_size;
+
+	if (spi_nor_has_uniform_erase(nor)) {
+		erase = spi_nor_select_uniform_erase(map, sector_size);
+		if (IS_ERR(erase))
+			return PTR_ERR(erase);
+		nor->erase_opcode = erase->opcode;
+		mtd->erasesize = erase->size;
+		return 0;
 	}
+
+	/*
+	 * For non-uniform SPI flash memory, set mtd->erasesize to the
+	 * maximum erase sector size. No need to set nor->erase_opcode.
+	 */
+	for (i = SNOR_ERASE_TYPE_MAX - 1; i >= 0; i--) {
+		if (map->erase_type[i].size) {
+			erase = &map->erase_type[i];
+			break;
+		}
+	}
+
+	if (!erase)
+		return -EINVAL;
+
+	mtd->erasesize = erase->size;
 	return 0;
 }
 
@@ -2712,7 +3103,7 @@ static int spi_nor_setup(struct spi_nor *nor, const struct flash_info *info,
 	}
 
 	/* Select the Sector Erase command. */
-	err = spi_nor_select_erase(nor, info);
+	err = spi_nor_select_erase(nor, info->sector_size);
 	if (err) {
 		dev_err(nor->dev,
 			"can't select erase settings supported by both the SPI controller and memory.\n");
include/linux/mtd/spi-nor.h +109 -0

133 lines not on this page · raw message

Signature · 1 line
2.9.4
#2 lore raw

PATCH v2 2/3 mtd: spi-nor: parse SFDP Sector Map Parameter Table

In reply to Tudor Ambarus

Add support for the SFDP (JESD216B) Sector Map Parameter Table. This table is optional, but when available, we parse it to identify the location and size of sectors within the main data array of the flash memory device and to identify which Erase Types are supported by each sector.

---
 drivers/mtd/spi-nor/spi-nor.c | 269 +++++++++++++++++++++++++++++++++++++++---
 include/linux/mtd/spi-nor.h   |  11 ++
 2 files changed, 264 insertions(+), 16 deletions(-)
drivers/mtd/spi-nor/spi-nor.c +253 -16
index 899b8c1..7c6291c 100644
@@ -2085,6 +2085,35 @@ spi_nor_set_pp_settings(struct spi_nor_pp_command *pp,
  */
 
 /**
+ * spi_nor_read_raw() - raw read of serial flash memory. read_opcode,
+ * addr_width and read_dummy members of the struct spi_nor should be previously
+ * set.
+ * @nor:	pointer to a 'struct spi_nor'
+ * @addr:	offset in the serial flash memory
+ * @len:	number of bytes to read
+ * @buf:	buffer where the data is copied into
+ *
+ * Return: 0 on success, -errno otherwise.
+ */
+static int spi_nor_read_raw(struct spi_nor *nor, u32 addr, size_t len, u8 *buf)
+{
+	int ret;
+
+	while (len) {
+		ret = nor->read(nor, addr, len, buf);
+		if (!ret || ret > len)
+			return -EIO;
+		if (ret < 0)
+			return ret;
+
+		buf += ret;
+		addr += ret;
+		len -= ret;
+	}
+	return 0;
+}
+
+/**
  * spi_nor_read_sfdp() - read Serial Flash Discoverable Parameters.
  * @nor:	pointer to a 'struct spi_nor'
  * @addr:	offset in the SFDP area to start reading data from
@@ -2111,22 +2140,8 @@ static int spi_nor_read_sfdp(struct spi_nor *nor, u32 addr,
 	nor->addr_width = 3;
 	nor->read_dummy = 8;
 
-	while (len) {
-		ret = nor->read(nor, addr, len, (u8 *)buf);
-		if (!ret || ret > len) {
-			ret = -EIO;
-			goto read_err;
-		}
-		if (ret < 0)
-			goto read_err;
+	ret = spi_nor_read_raw(nor, addr, len, buf);
 
-		buf += ret;
-		addr += ret;
-		len -= ret;
-	}
-	ret = 0;
-
-read_err:
 	nor->read_opcode = read_opcode;
 	nor->addr_width = addr_width;
 	nor->read_dummy = read_dummy;
@@ -2646,6 +2661,228 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
 	return 0;
 }
 
+#define SMPT_CMD_ADDRESS_LEN_MASK		GENMASK(23, 22)
+#define SMPT_CMD_ADDRESS_LEN_0			(0x0UL << 22)
+#define SMPT_CMD_ADDRESS_LEN_3			(0x1UL << 22)
+#define SMPT_CMD_ADDRESS_LEN_4			(0x2UL << 22)
+#define SMPT_CMD_ADDRESS_LEN_USE_CURRENT	(0x3UL << 22)
+
+#define SMPT_CMD_READ_DUMMY_MASK		GENMASK(19, 16)
+#define SMPT_CMD_READ_DUMMY_SHIFT		16
+#define SMPT_CMD_READ_DUMMY(_cmd) \
+	((_cmd & SMPT_CMD_READ_DUMMY_MASK) >> SMPT_CMD_READ_DUMMY_SHIFT)
+#define SMPT_CMD_READ_DUMMY_IS_VARIABLE		0xfUL
+
+#define SMPT_CMD_READ_DATA_MASK			GENMASK(31, 24)
+#define SMPT_CMD_READ_DATA_SHIFT		24
+#define SMPT_CMD_READ_DATA(_cmd) \
+	((_cmd & SMPT_CMD_READ_DATA_MASK) >> SMPT_CMD_READ_DATA_SHIFT)
+
+#define SMPT_CMD_OPCODE_MASK			GENMASK(15, 8)
+#define SMPT_CMD_OPCODE_SHIFT			8
+#define SMPT_CMD_OPCODE(_cmd) \
+	((_cmd & SMPT_CMD_OPCODE_MASK) >> SMPT_CMD_OPCODE_SHIFT)
+
+#define SMPT_MAP_REGION_COUNT_MASK		GENMASK(23, 16)
+#define SMPT_MAP_REGION_COUNT_SHIFT		16
+#define SMPT_MAP_REGION_COUNT(_header) \
+	(((_header & SMPT_MAP_REGION_COUNT_MASK) >> \
+	  SMPT_MAP_REGION_COUNT_SHIFT) + 1)
+
+#define SMPT_MAP_ID_MASK			GENMASK(15, 8)
+#define SMPT_MAP_ID_SHIFT			8
+#define SMPT_MAP_ID(_header) ((_header & SMPT_MAP_ID_MASK) >> SMPT_MAP_ID_SHIFT)
+
+#define SMPT_MAP_REGION_SIZE_MASK		GENMASK(31, 8)
+#define SMPT_MAP_REGION_SIZE_SHIFT		8
+#define SMPT_MAP_REGION_SIZE(_region) \
+	((((_region & SMPT_MAP_REGION_SIZE_MASK) >> \
+	   SMPT_MAP_REGION_SIZE_SHIFT) + 1) * 256)
+
+#define SMPT_MAP_REGION_ERASE_TYPE_MASK		GENMASK(3, 0)
+#define SMPT_MAP_REGION_ERASE_TYPE(_region) \
+	(_region & SMPT_MAP_REGION_ERASE_TYPE_MASK)
+
+#define SMPT_DESC_TYPE_MAP			BIT(1)
+#define SMPT_DESC_END				BIT(0)
+
+static u8 spi_nor_smpt_addr_width(const struct spi_nor *nor, const u32 settings)
+{
+	switch (settings & SMPT_CMD_ADDRESS_LEN_MASK) {
+	case SMPT_CMD_ADDRESS_LEN_0:
+		return 0;
+	case SMPT_CMD_ADDRESS_LEN_3:
+		return 3;
+	case SMPT_CMD_ADDRESS_LEN_4:
+		return 4;
+	case SMPT_CMD_ADDRESS_LEN_USE_CURRENT:
+		/* fall through */
+	default:
+		return nor->addr_width;
+	}
+}
+
+static u8 spi_nor_smpt_read_dummy(const struct spi_nor *nor, const u32 settings)
+{
+	u8 read_dummy = SMPT_CMD_READ_DUMMY(settings);
+
+	if (read_dummy == SMPT_CMD_READ_DUMMY_IS_VARIABLE)
+		return nor->read_dummy;
+	return read_dummy;
+}
+
+static const u32 *spi_nor_get_map_in_use(struct spi_nor *nor, const u32 *smpt)
+{
+	const u32 *ret = NULL;
+	u32 i, addr;
+	int err;
+	u8 addr_width, read_opcode, read_dummy;
+	u8 read_data_mask, data_byte, map_id;
+
+	addr_width = nor->addr_width;
+	read_dummy = nor->read_dummy;
+	read_opcode = nor->read_opcode;
+
+	map_id = 0;
+	i = 0;
+	/* Determine if there are any optional Detection Command Descriptors */
+	while (!(smpt[i] & SMPT_DESC_TYPE_MAP)) {
+		read_data_mask = SMPT_CMD_READ_DATA(smpt[i]);
+		nor->addr_width = spi_nor_smpt_addr_width(nor, smpt[i]);
+		nor->read_dummy = spi_nor_smpt_read_dummy(nor, smpt[i]);
+		nor->read_opcode = SMPT_CMD_OPCODE(smpt[i]);
+		addr = smpt[i + 1];
+
+		err = spi_nor_read_raw(nor, addr, 1, &data_byte);
+		if (err)
+			goto out;
+
+		/*
+		 * Build an index value that is used to select the Sector Map
+		 * Configuration that is currently in use.
+		 */
+		map_id = map_id << 1 | (!(data_byte & read_data_mask) ? 0 : 1);
+		i = i + 2;
+	}
+
+	/* Find the matching configuration map */
+	while (SMPT_MAP_ID(smpt[i]) != map_id) {
+		if (smpt[i] & SMPT_DESC_END)
+			goto out;
+		/* increment the table index to the next map */
+		i += SMPT_MAP_REGION_COUNT(smpt[i]) + 1;
+	}
+
+	ret = smpt + i;
+	/* fall through */
+out:
+	nor->addr_width = addr_width;
+	nor->read_dummy = read_dummy;
+	nor->read_opcode = read_opcode;
+	return ret;
+}
+
+static void
+spi_nor_region_check_overlay(struct spi_nor_erase_region *region,
+			     const struct spi_nor_erase_type *erase,
+			     const u8 erase_type)
+{
+	int i;
+
+	for (i = 0; i < SNOR_ERASE_TYPE_MAX; i++) {
+		if (!(erase_type & BIT(i)))
+			continue;
+		if (region->size & erase[i].size_mask) {
+			spi_nor_region_mark_overlay(region);
+			return;
+		}
+	}
+}
+
+static int spi_nor_init_non_uniform_erase_map(struct spi_nor *nor,
+					      const u32 *smpt)
+{
+	struct spi_nor_erase_map *map = &nor->erase_map;
+	const struct spi_nor_erase_type *erase = map->erase_type;
+	struct spi_nor_erase_region *region;
+	u64 offset;
+	u32 region_count;
+	int i, j;
+	u8 erase_type;
+
+	region_count = SMPT_MAP_REGION_COUNT(*smpt);
+	region = devm_kcalloc(nor->dev, region_count, sizeof(*region),
+			      GFP_KERNEL);
+	if (!region)
+		return -ENOMEM;
+	map->regions = region;
+
+	map->uniform_erase_type = 0xff;
+	offset = 0;
+	for (i = 0; i < region_count; i++) {
+		j = i + 1; /* index for the region dword */
+		region[i].size = SMPT_MAP_REGION_SIZE(smpt[j]);
+		erase_type = SMPT_MAP_REGION_ERASE_TYPE(smpt[j]);
+		region[i].offset = offset | erase_type;
+
+		spi_nor_region_check_overlay(&region[i], erase, erase_type);
+
+		/*
+		 * Save the erase types that are supported in all regions and
+		 * can erase the entire flash memory.
+		 */
+		map->uniform_erase_type &= erase_type;
+
+		offset = (region[i].offset & ~SNOR_ERASE_FLAGS_MASK) +
+			 region[i].size;
+	}
+
+	spi_nor_region_mark_end(&region[i - 1]);
+
+	return 0;
+}
+
+static int spi_nor_parse_smpt(struct spi_nor *nor,
+			      const struct sfdp_parameter_header *smpt_header)
+{
+	const u32 *sector_map;
+	u32 *smpt;
+	size_t len;
+	u32 addr;
+	int i, ret;
+
+	/* Read the Sector Map Parameter Table. */
+	len = smpt_header->length * sizeof(*smpt);
+	smpt = kzalloc(len, GFP_KERNEL);
+	if (!smpt)
+		return -ENOMEM;
+
+	addr = SFDP_PARAM_HEADER_PTP(smpt_header);
+	ret = spi_nor_read_sfdp(nor, addr, len, smpt);
+	if (ret)
+		goto out;
+
+	/* Fix endianness of the SMPT DWORDs. */
+	for (i = 0; i < smpt_header->length; i++)
+		smpt[i] = le32_to_cpu(smpt[i]);
+
+	sector_map = spi_nor_get_map_in_use(nor, smpt);
+	if (!sector_map) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ret = spi_nor_init_non_uniform_erase_map(nor, sector_map);
+	if (ret)
+		goto out;
+
+	spi_nor_regions_sort_erase_types(&nor->erase_map);
+	/* fall through */
+out:
+	kfree(smpt);
+	return ret;
+}
+
 /**
  * spi_nor_parse_sfdp() - parse the Serial Flash Discoverable Parameters.
  * @nor:		pointer to a 'struct spi_nor'
@@ -2740,7 +2977,7 @@ static int spi_nor_parse_sfdp(struct spi_nor *nor,
 
 		switch (SFDP_PARAM_HEADER_ID(param_header)) {
 		case SFDP_SECTOR_MAP_ID:
-			dev_info(dev, "non-uniform erase sector maps are not supported yet.\n");
+			err = spi_nor_parse_smpt(nor, param_header);
 			break;
 
 		default:
include/linux/mtd/spi-nor.h +11 -0
index 2131963..25941ea 100644
@@ -420,6 +420,17 @@ static inline u64 spi_nor_region_end(const struct spi_nor_erase_region *region)
 	return (region->offset & ~SNOR_ERASE_FLAGS_MASK) + region->size;
 }
 
+static inline void spi_nor_region_mark_end(struct spi_nor_erase_region *region)
+{
+	region->offset |= SNOR_LAST_REGION;
+}
+
+static inline void
+spi_nor_region_mark_overlay(struct spi_nor_erase_region *region)
+{
+	region->offset |= SNOR_OVERLAID_REGION;
+}
+
 static inline bool spi_nor_has_uniform_erase(const struct spi_nor *nor)
 {
 	return !!nor->erase_map.uniform_erase_type;
Signature · 1 line
2.9.4
#3 lore raw

PATCH v2 3/3 mtd: spi-nor: parse SFDP 4-byte Address Instruction Table

In reply to Tudor Ambarus

From: Cyrille Pitchen <[email protected]>

Add support for SFDP (JESD216B) 4-byte Address Instruction Table. This table is optional but when available, we parse it to get the 4-byte address op codes supported by the memory.
Using these op codes is stateless as opposed to entering the 4-byte address mode or setting the Base Address Register (BAR).

---
 drivers/mtd/spi-nor/spi-nor.c | 148 ++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 148 insertions(+)
drivers/mtd/spi-nor/spi-nor.c +148 -0
index 7c6291c..74f9b46 100644
@@ -2196,6 +2196,7 @@ struct sfdp_parameter_header {
 
 #define SFDP_BFPT_ID		0xff00	/* Basic Flash Parameter Table */
 #define SFDP_SECTOR_MAP_ID	0xff81	/* Sector Map Table */
+#define SFDP_4BAIT_ID		0xff84u	/* 4-byte Address Instruction Table */
 
 #define SFDP_SIGNATURE		0x50444653U
 #define SFDP_JESD216_MAJOR	1
@@ -2883,6 +2884,149 @@ static int spi_nor_parse_smpt(struct spi_nor *nor,
 	return ret;
 }
 
+struct sfdp_4bait {
+	/* The hardware capability. */
+	u32		hwcaps;
+
+	/*
+	 * The <supported_bit> bit in DWORD1 of the 4BAIT tells us whether
+	 * the associated 4-byte address op code is supported.
+	 */
+	u32		supported_bit;
+};
+
+static int spi_nor_parse_4bait(struct spi_nor *nor,
+			       const struct sfdp_parameter_header *param_header,
+			       struct spi_nor_flash_parameter *params)
+{
+	static const struct sfdp_4bait reads[] = {
+		{ SNOR_HWCAPS_READ,		BIT(0) },
+		{ SNOR_HWCAPS_READ_FAST,	BIT(1) },
+		{ SNOR_HWCAPS_READ_1_1_2,	BIT(2) },
+		{ SNOR_HWCAPS_READ_1_2_2,	BIT(3) },
+		{ SNOR_HWCAPS_READ_1_1_4,	BIT(4) },
+		{ SNOR_HWCAPS_READ_1_4_4,	BIT(5) },
+		{ SNOR_HWCAPS_READ_1_1_1_DTR,	BIT(13) },
+		{ SNOR_HWCAPS_READ_1_2_2_DTR,	BIT(14) },
+		{ SNOR_HWCAPS_READ_1_4_4_DTR,	BIT(15) },
+	};
+	static const struct sfdp_4bait programs[] = {
+		{ SNOR_HWCAPS_PP,		BIT(6) },
+		{ SNOR_HWCAPS_PP_1_1_4,		BIT(7) },
+		{ SNOR_HWCAPS_PP_1_4_4,		BIT(8) },
+	};
+	static const struct sfdp_4bait erases[SNOR_ERASE_TYPE_MAX] = {
+		{ 0u /* not used */,		BIT(9) },
+		{ 0u /* not used */,		BIT(10) },
+		{ 0u /* not used */,		BIT(11) },
+		{ 0u /* not used */,		BIT(12) },
+	};
+	u32 dwords[2], addr, discard_hwcaps, read_hwcaps, pp_hwcaps, erase_mask;
+	struct spi_nor_erase_map *map = &nor->erase_map;
+	int i, err;
+
+	if (param_header->major != SFDP_JESD216_MAJOR ||
+	    param_header->length < ARRAY_SIZE(dwords))
+		return -EINVAL;
+
+	/* Read the 4-byte Address Instruction Table. */
+	addr = SFDP_PARAM_HEADER_PTP(param_header);
+	err = spi_nor_read_sfdp(nor, addr, sizeof(dwords), dwords);
+	if (err)
+		return err;
+
+	/* Fix endianness of the 4BAIT DWORDs. */
+	for (i = 0; i < ARRAY_SIZE(dwords); i++)
+		dwords[i] = le32_to_cpu(dwords[i]);
+
+	/*
+	 * Compute the subset of (Fast) Read commands for which the 4-byte
+	 * version is supported.
+	 */
+	discard_hwcaps = 0;
+	read_hwcaps = 0;
+	for (i = 0; i < ARRAY_SIZE(reads); i++) {
+		const struct sfdp_4bait *read = &reads[i];
+
+		discard_hwcaps |= read->hwcaps;
+		if ((params->hwcaps.mask & read->hwcaps) &&
+		    (dwords[0] & read->supported_bit))
+			read_hwcaps |= read->hwcaps;
+	}
+
+	/*
+	 * Compute the subset of Page Program commands for which the 4-byte
+	 * version is supported.
+	 */
+	pp_hwcaps = 0;
+	for (i = 0; i < ARRAY_SIZE(programs); i++) {
+		const struct sfdp_4bait *program = &programs[i];
+
+		discard_hwcaps |= program->hwcaps;
+		if ((params->hwcaps.mask & program->hwcaps) &&
+		    (dwords[0] & program->supported_bit))
+			pp_hwcaps |= program->hwcaps;
+	}
+
+	/*
+	 * Compute the subet of Sector Erase commands for which the 4-byte
+	 * version is supported.
+	 */
+	erase_mask = 0;
+	for (i = 0; i < SNOR_ERASE_TYPE_MAX; i++) {
+		const struct sfdp_4bait *erase = &erases[i];
+
+		if (map->erase_type[i].size > 0 &&
+		    (dwords[0] & erase->supported_bit))
+			erase_mask |= BIT(i);
+	}
+
+	/*
+	 * We need at least one 4-byte op code per read, program and erase
+	 * operation; the .read(), .write() and .erase() hooks share the
+	 * nor->addr_width value.
+	 */
+	if (!read_hwcaps || !pp_hwcaps || !erase_mask)
+		return 0;
+
+	/*
+	 * Discard all operations from the 4-byte instruction set which are
+	 * not supported by this memory.
+	 */
+	params->hwcaps.mask &= ~discard_hwcaps;
+	params->hwcaps.mask |= (read_hwcaps | pp_hwcaps);
+
+	/* Use the 4-byte address instruction set. */
+	for (i = 0; i < SNOR_CMD_READ_MAX; i++) {
+		struct spi_nor_read_command *read_cmd = &params->reads[i];
+
+		read_cmd->opcode = spi_nor_convert_3to4_read(read_cmd->opcode);
+	}
+	for (i = 0; i < SNOR_CMD_PP_MAX; i++) {
+		struct spi_nor_pp_command *pp_cmd = &params->page_programs[i];
+
+		pp_cmd->opcode = spi_nor_convert_3to4_program(pp_cmd->opcode);
+	}
+	for (i = 0; i < SNOR_ERASE_TYPE_MAX; i++) {
+		struct spi_nor_erase_type *erase = &map->erase_type[i];
+
+		if (erase_mask & BIT(erase->idx))
+			erase->opcode = (dwords[1] >> (erase->idx * 8)) & 0xFF;
+		else
+			spi_nor_set_erase_type(erase, 0u, 0xFF);
+	}
+
+	/*
+	 * We set nor->addr_width here to skip spi_nor_set_4byte_opcodes()
+	 * later because this latest function implements a legacy quirk for
+	 * the erase size of Spansion memory. However this quirk is no longer
+	 * needed with new SFDP compliant memories.
+	 */
+	nor->addr_width = 4;
+	nor->flags |= SPI_NOR_4B_OPCODES;
+	return 0;
+}
+
 /**
  * spi_nor_parse_sfdp() - parse the Serial Flash Discoverable Parameters.
  * @nor:		pointer to a 'struct spi_nor'
@@ -2980,6 +3124,10 @@ static int spi_nor_parse_sfdp(struct spi_nor *nor,
 			err = spi_nor_parse_smpt(nor, param_header);
 			break;
 
+		case SFDP_4BAIT_ID:
+			err = spi_nor_parse_4bait(nor, param_header, params);
+			break;
+
 		default:
 			break;
 		}
Signature · 1 line
2.9.4
#4 lore raw
In reply to Tudor Ambarus

As a side note, the SFDP code increases its size, it would make sense to move all SFDP logic into a spi-nor-sfdp.c file. I'm volunteering to do this after this patch set gets applied.

Best,
ta

#5 lore raw
In reply to Tudor Ambarus

Hi, Marek,

Did you have the chance to look over these patches? Please advise how can I move forward with the non-uniform erase support.

Thanks,
ta

Quoted 61 lines · Tudor Ambarus

Backward compatibility test done on mx25l3273fm2i-08g. Non-uniform erase test done on sst26vf064b-104i/sn.

Note that in order to do the non-uniform test on the aforementioned memory you'll have to force the spi_nor_has_uniform_erase() to return false, because the erase map is tuned to come back to the uniform case. Also, you'll have to unlock the global protection on the flash. There was an attempt to unlock this protection, but for whatever reason the patch was not taken:
https://patchwork.ozlabs.org/patch/544270/. I'm taking care of the global protection lock on sst26vf064b-104i/sn, I will submit a patch soon.

Changes in v2:
- add JESD216B SFDP optional parser: Sector Map Parameter Table parser and 4-byte Address Instruction Table parser (patch 2/3 and patch 3/3).
- fix condition on finding erase regions
- fix the list command adding
- write_enable(nor); before erasing the sectors
- As Boris suggested, remove likely() because it doesn't make any difference given the time it takes to actually erase the block.
- save the Erase Types from bfpt, to determine the Erase Type sizes. Sort all the map's Erase Types in ascending order with the smallest erase size being the first member in the erase_type array. Sort Erase Type mask in regions. We sort the Erase Type by size, at init, in order to speed up the process of finding the best erase command at run-time.
- spi_nor_select_erase(): pass directly info->sector_size instead of the whole flash_info structure in order to simplify the code.
- keep the same convention as most flashes, and order erase types by size with the smallest Erase Type size starting at index 0/ BIT(0).
- return unused function: spi_nor_region_mark_end().
- fix return value of spi_nor_has_uniform_erase().
- remove setting of mtd->erasesize and nor->erase_opcode when parsing the Basic Flash Parameter Table. mtd->erasesize was set to the maximum supported Erase Type size, without verifying if that Erase Type can erase the entire flash. mtd->erasesize is now set just in spi_nor_select_erase(), after we find which Erase Types are supported in the uniform case.

Changes in v1 or what I've done on top of Cyrille's work (https://lkml.org/lkml/2017/4/15/70):
- minimize the amount of erase() calls by using the best sequence of erase
type commands depending on alignment.
- build the list of best fitted erase commands to be executed once we
validate that the erase can be performed.
- add improvements on how the erase map is handled. The regions are
consecutive in the address space, walk through the regions incrementally.
- speed up finding the best erase type command. Order erase types by
size, iterate them from the biggest to the smallest and stop when best
fitted command is found.
- determine at init if there are erase types that can erase the entire
memory
- fix support for overlaid regions.

Cyrille Pitchen (1):
mtd: spi-nor: parse SFDP 4-byte Address Instruction Table

Tudor Ambarus (2):
mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
mtd: spi-nor: parse SFDP Sector Map Parameter Table

 drivers/mtd/spi-nor/spi-nor.c | 892 +++++++++++++++++++++++++++++++++++++++---
 include/linux/mtd/spi-nor.h   | 120 ++++++
 2 files changed, 954 insertions(+), 58 deletions(-)