drivers: esdhc: add support for ColdFire mcf5441x family

index 4528345c67..315c24527d 100644
@@ -382,6 +382,25 @@ static void check_and_invalidate_dcache_range
 	invalidate_dcache_range(start, end);
 }
 
+#ifdef CONFIG_MCF5441x
+/*
+ * Swaps 32-bit words to little-endian byte order.
+ */
+static inline void sd_swap_dma_buff(struct mmc_data *data)
+{
+	int i, size = data->blocksize >> 2;
+	u32 *buffer = (u32 *)data->dest;
+	u32 sw;
+
+	while (data->blocks--) {
+		for (i = 0; i < size; i++) {
+			sw = __sw32(*buffer);
+			*buffer++ = sw;
+		}
+	}
+}
+#endif
+
 /*
  * Sends a command out on the bus.  Takes the mmc pointer,
  * a command pointer, and an optional data pointer.

@@ -538,8 +557,12 @@ static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc,
 		 * cache-fill during the DMA operations such as the
 		 * speculative pre-fetching etc.
 		 */
-		if (data->flags & MMC_DATA_READ)
+		if (data->flags & MMC_DATA_READ) {
 			check_and_invalidate_dcache_range(cmd, data);
+#ifdef CONFIG_MCF5441x
+			sd_swap_dma_buff(data);
+#endif
+		}
 #endif
 	}
 

@@ -987,8 +1010,12 @@ static int esdhc_init_common(struct fsl_esdhc_priv *priv, struct mmc *mmc)
 	/* Disable the BRR and BWR bits in IRQSTAT */
 	esdhc_clrbits32(&regs->irqstaten, IRQSTATEN_BRR | IRQSTATEN_BWR);
 
+#ifdef CONFIG_MCF5441x
+	esdhc_write32(&regs->proctl, PROCTL_INIT | PROCTL_D3CD);
+#else
 	/* Put the PROCTL reg back to the default */
 	esdhc_write32(&regs->proctl, PROCTL_INIT);
+#endif
 
 	/* Set timout to the maximum value */
 	esdhc_clrsetbits32(&regs->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16);

@@ -1096,6 +1123,11 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
 	if (ret)
 		return ret;
 
+#ifdef CONFIG_MCF5441x
+	/* ColdFire, using SDHC_DATA[3] for card detection */
+	esdhc_write32(&regs->proctl, PROCTL_INIT | PROCTL_D3CD);
+#endif
+
 #ifndef CONFIG_FSL_USDHC
 	esdhc_setbits32(&regs->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
 				| SYSCTL_IPGEN | SYSCTL_CKEN);

@@ -1120,6 +1152,15 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
 	voltage_caps = 0;
 	caps = esdhc_read32(&regs->hostcapblt);
 
+#ifdef CONFIG_MCF5441x
+	/*
+	 * MCF5441x RM declares in more points that sdhc clock speed must
+	 * never exceed 25 Mhz. From this, the HS bit needs to be disabled
+	 * from host capabilities.
+	 */
+	caps &= ~ESDHC_HOSTCAPBLT_HSS;
+#endif
+
 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC135
 	caps = caps & ~(ESDHC_HOSTCAPBLT_SRS |
 			ESDHC_HOSTCAPBLT_VS18 | ESDHC_HOSTCAPBLT_VS30);

index acd8dd06f8..8dbd5249a7 100644
@@ -106,6 +106,7 @@
 #define PROCTL_INIT		0x00000020
 #define PROCTL_DTW_4		0x00000002
 #define PROCTL_DTW_8		0x00000004
+#define PROCTL_D3CD		0x00000008
 
 #define CMDARG			0x0002e008