net: phy: mscc: factorize code for LEDs mode
Subsystems (4)
PATCH v2 1/7 net: phy: mscc: factorize code for LEDs mode
LEDs modes are set the same way, except they are offset by 4 times the index of the LED.
Let's factorize all the code so that it's easier to add support for the 4 LEDs of the VSC8584 PHY.
--- drivers/net/phy/mscc.c | 75 ++++++++++++++++++++++-------------------- 1 file changed, 39 insertions(+), 36 deletions(-)
drivers/net/phy/mscc.c +39 -36
@@ -54,9 +54,9 @@ enum rgmii_rx_clock_delay {#define HP_AUTO_MDIX_X_OVER_IND_MASK 0x2000#define MSCC_PHY_LED_MODE_SEL 29 -#define LED_1_MODE_SEL_MASK 0x00F0 -#define LED_0_MODE_SEL_MASK 0x000F -#define LED_1_MODE_SEL_POS 4 +#define LED_MODE_SEL_POS (x) ((x) * 4) +#define LED_MODE_SEL_MASK (x) (GENMASK(3, 0) << LED_MODE_SEL_POS(x)) +#define LED_MODE_SEL (x, mode) (((mode) << LED_MODE_SEL_POS(x)) & LED_MODE_SEL_MASK(x))#define MSCC_EXT_PAGE_ACCESS 31#define MSCC_PHY_PAGE_STANDARD 0x0000/* Standard registers */
@@ -103,10 +103,11 @@ enum rgmii_rx_clock_delay {#define DOWNSHIFT_COUNT_MAX 5 +#define MAX_LEDS 4struct vsc8531_private {int rate_magic; -u8 led_0_mode; -u8 led_1_mode; +u8 leds_mode[MAX_LEDS ]; +u8 nleds; };#ifdef CONFIG_OF_MDIO
@@ -140,14 +141,8 @@ static int vsc85xx_led_cntl_set(struct phy_device *phydev,mutex_lock (&phydev->lock); reg_val =phy_read (phydev,MSCC_PHY_LED_MODE_SEL ); -if (led_num) { - reg_val &= ~LED_1_MODE_SEL_MASK ; - reg_val |= (((u16 )mode <<LED_1_MODE_SEL_POS ) & -LED_1_MODE_SEL_MASK ); - }else { - reg_val &= ~LED_0_MODE_SEL_MASK ; - reg_val |= ((u16 )mode &LED_0_MODE_SEL_MASK ); - } + reg_val &= ~LED_MODE_SEL_MASK (led_num); + reg_val |=LED_MODE_SEL (led_num, (u16 )mode); rc =phy_write (phydev,MSCC_PHY_LED_MODE_SEL , reg_val);mutex_unlock (&phydev->lock);
@@ -438,6 +433,27 @@ static int vsc85xx_dt_led_mode_get(struct phy_device *phydev, }#endif /* CONFIG_OF_MDIO */ +static int vsc85xx_dt_led_modes_get (struct phy_device *phydev,u8 *default_mode) +{ +struct vsc8531_private *priv = phydev->priv; +char led_dt_prop[19 ]; +int i, ret; + +for (i =0 ; i < priv->nleds; i++) { + ret =sprintf (led_dt_prop,"vsc8531,led-%d-mode" , i); +if (ret <0 ) +return ret; + + ret =vsc85xx_dt_led_mode_get (phydev, led_dt_prop, + default_mode[i]); +if (ret <0 ) +return ret; + priv->leds_mode[i] = ret; + } + +return 0 ; +} +static int vsc85xx_edge_rate_cntl_set (struct phy_device *phydev,u8 edge_rate) {int rc;
@@ -545,7 +561,7 @@ static int vsc85xx_set_tunable(struct phy_device *phydev,static int vsc85xx_config_init (struct phy_device *phydev) { -int rc; +int rc, i;struct vsc8531_private *vsc8531 = phydev->priv; rc =vsc85xx_default_config (phydev);
@@ -560,13 +576,11 @@ static int vsc85xx_config_init(struct phy_device *phydev)if (rc)return rc; - rc =vsc85xx_led_cntl_set (phydev,1 , vsc8531->led_1_mode); -if (rc) -return rc; - - rc =vsc85xx_led_cntl_set (phydev,0 , vsc8531->led_0_mode); -if (rc) -return rc; +for (i =0 ; i < vsc8531->nleds; i++) { + rc =vsc85xx_led_cntl_set (phydev, i, vsc8531->leds_mode[i]); +if (rc) +return rc; + } rc =genphy_config_init (phydev);
@@ -626,7 +640,8 @@ static int vsc85xx_probe(struct phy_device *phydev) {struct vsc8531_private *vsc8531;int rate_magic; -int led_mode; +u8 default_mode[2 ] = {VSC8531_LINK_1000_ACTIVITY , +VSC8531_LINK_100_ACTIVITY }; rate_magic =vsc85xx_edge_rate_magic_get (phydev);if (rate_magic <0 )
@@ -639,21 +654,9 @@ static int vsc85xx_probe(struct phy_device *phydev) phydev->priv = vsc8531; vsc8531->rate_magic = rate_magic; + vsc8531->nleds =2 ; -/* LED[0] and LED[1] mode */ - led_mode =vsc85xx_dt_led_mode_get (phydev,"vsc8531,led-0-mode" , -VSC8531_LINK_1000_ACTIVITY ); -if (led_mode <0 ) -return led_mode; - vsc8531->led_0_mode = led_mode; - - led_mode =vsc85xx_dt_led_mode_get (phydev,"vsc8531,led-1-mode" , -VSC8531_LINK_100_ACTIVITY ); -if (led_mode <0 ) -return led_mode; - vsc8531->led_1_mode = led_mode; - -return 0 ; +return vsc85xx_dt_led_modes_get (phydev, default_mode); }/* Microsemi VSC85xx PHYs */
Signature · 1 line
2.17.1
PATCH v2 2/7 net: phy: mscc: factorize function for getting LED mode from DT
Microsemi PHYs support different LED modes depending on the variant, so let's factorize the code so we just have to give the supported modes while the logic behind getting the mode remains identical.
---
added in v2
drivers/net/phy/mscc.c | 20 +++++++++++++++++++- 1 file changed, 19 insertions(+), 1 deletion(-)
drivers/net/phy/mscc.c +19 -1
@@ -104,8 +104,24 @@ enum rgmii_rx_clock_delay {#define DOWNSHIFT_COUNT_MAX 5#define MAX_LEDS 4 +#define VSC85XX_SUPP_LED_MODES (BIT(VSC8531_LINK_ACTIVITY) | \ + BIT(VSC8531_LINK_1000_ACTIVITY) | \ + BIT(VSC8531_LINK_100_ACTIVITY) | \ + BIT(VSC8531_LINK_10_ACTIVITY) | \ + BIT(VSC8531_LINK_100_1000_ACTIVITY) | \ + BIT(VSC8531_LINK_10_1000_ACTIVITY) | \ + BIT(VSC8531_LINK_10_100_ACTIVITY) | \ + BIT(VSC8531_DUPLEX_COLLISION) | \ + BIT(VSC8531_COLLISION) | \ + BIT(VSC8531_ACTIVITY) | \ + BIT(VSC8531_AUTONEG_FAULT) | \ + BIT(VSC8531_SERIAL_MODE) | \ + BIT(VSC8531_FORCE_LED_OFF) | \ + BIT(VSC8531_FORCE_LED_ON)) +struct vsc8531_private {int rate_magic; +u16 supp_led_modes;u8 leds_mode[MAX_LEDS ];u8 nleds; };
@@ -401,6 +417,7 @@ static int vsc85xx_dt_led_mode_get(struct phy_device *phydev, char *led, u8 default_mode) { +struct vsc8531_private *priv = phydev->priv;struct device *dev = &phydev->mdio.dev;struct device_node *of_node = dev->of_node;u8 led_mode;
@@ -411,7 +428,7 @@ static int vsc85xx_dt_led_mode_get(struct phy_device *phydev, led_mode = default_mode; err =of_property_read_u8 (of_node, led, &led_mode); -if (!err && (led_mode >15 || led_mode ==7 || led_mode ==11 )) { +if (!err && !(BIT (led_mode) & priv->supp_led_modes)) {phydev_err (phydev,"DT %s invalid\n" , led);return -EINVAL ; }
@@ -655,6 +672,7 @@ static int vsc85xx_probe(struct phy_device *phydev) vsc8531->rate_magic = rate_magic; vsc8531->nleds =2 ; + vsc8531->supp_led_modes =VSC85XX_SUPP_LED_MODES ;return vsc85xx_dt_led_modes_get (phydev, default_mode); }
Signature · 1 line
2.17.1
PATCH v2 3/7 net: phy: mscc: read 'vsc8531,vddmac' as an u32
In reply to Quentin SchulzIn the DT binding, it is specified nowhere that 'vsc8531,vddmac' is an u16, even though it's read as an u16 in the driver.
Let's update the driver to take into consideration that the 'vsc8531,vddmac' property is of the default type u32.
---
added in v2
drivers/net/phy/mscc.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/net/phy/mscc.c +3 -3
@@ -128,7 +128,7 @@ struct vsc8531_private {#ifdef CONFIG_OF_MDIO struct vsc8531_edge_rate_table { -u16 vddmac; +u32 vddmac;u8 slowdown[8 ]; };
@@ -387,7 +387,7 @@ static void vsc85xx_wol_get(struct phy_device *phydev,static int vsc85xx_edge_rate_magic_get (struct phy_device *phydev) {u8 sd; -u16 vdd; +u32 vdd;int rc, i, j;struct device *dev = &phydev->mdio.dev;struct device_node *of_node = dev->of_node;
@@ -396,7 +396,7 @@ static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)if (!of_node)return -ENODEV ; - rc =of_property_read_u16 (of_node,"vsc8531,vddmac" , &vdd); + rc =of_property_read_u32 (of_node,"vsc8531,vddmac" , &vdd);if (rc !=0 ) vdd =MSCC_VDDMAC_3300 ;
Signature · 1 line
2.17.1
PATCH v2 4/7 net: phy: mscc: read 'vsc8531,edge-slowdown' as an u32
In reply to Quentin SchulzIn the DT binding, it is specified nowhere that 'vsc8531,edge-slowdown' is an u8, even though it's read as an u8 in the driver.
Let's update the driver to take into consideration that the 'vsc8531,edge-slowdown' property is of the default type u32.
---
added in v2
drivers/net/phy/mscc.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-)
drivers/net/phy/mscc.c +3 -4
@@ -129,7 +129,7 @@ struct vsc8531_private {#ifdef CONFIG_OF_MDIO struct vsc8531_edge_rate_table {u32 vddmac; -u8 slowdown[8 ]; +u32 slowdown[8 ]; }; static const struct vsc8531_edge_rate_table edge_table[] = {
@@ -386,8 +386,7 @@ static void vsc85xx_wol_get(struct phy_device *phydev,#ifdef CONFIG_OF_MDIO static int vsc85xx_edge_rate_magic_get (struct phy_device *phydev) { -u8 sd; -u32 vdd; +u32 vdd, sd;int rc, i, j;struct device *dev = &phydev->mdio.dev;struct device_node *of_node = dev->of_node;
@@ -400,7 +399,7 @@ static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)if (rc !=0 ) vdd =MSCC_VDDMAC_3300 ; - rc =of_property_read_u8 (of_node,"vsc8531,edge-slowdown" , &sd); + rc =of_property_read_u32 (of_node,"vsc8531,edge-slowdown" , &sd);if (rc !=0 ) sd =0 ;
Signature · 1 line
2.17.1
Andrew Lunn
maintainerRe: [PATCH net-next v2 4/7] net: phy: mscc: read 'vsc8531,edge-slowdown' as an u32
Quoted 2 lines · Quentin Schulz
In the DT binding, it is specified nowhere that 'vsc8531,edge-slowdown' is an u8, even though it's read as an u8 in the driver.
Hi Quentin
of_property_read_u8() will perform bounds checking. Is that important here?
Thanks
Andrew
Re: [PATCH net-next v2 4/7] net: phy: mscc: read 'vsc8531,edge-slowdown' as an u32
Hi Andrew,
Quoted 9 lines · Andrew Lunn
Quoted 2 lines · Quentin Schulz
In the DT binding, it is specified nowhere that 'vsc8531,edge-slowdown' is an u8, even though it's read as an u8 in the driver.
Hi Quentin
of_property_read_u8()will perform bounds checking. Is that important here?
Just to be sure, we're talking here about making sure the value stored in the DT is not bigger than the specified value (here an u8)? If so, that isn't the reason why I'm suggesting those two patches.
Without /bits 8/ in the DT property, whatever were the values I put in the property, I'd always get a 0. So I need to fix it either in the DT (but Rob does not really like it) or in the driver.
Hope that makes sense.
Quentin
Andrew Lunn
maintainerRe: [PATCH net-next v2 4/7] net: phy: mscc: read 'vsc8531,edge-slowdown' as an u32
Quoted 7 lines
Just to be sure, we're talking here about making sure the value stored in the DT is not bigger than the specified value (here an u8)? If so, that isn't the reason why I'm suggesting those two patches.
Without /bits 8/ in the DT property, whatever were the values I put in the property, I'd always get a 0. So I need to fix it either in the DT (but Rob does not really like it) or in the driver.
Hi Quentin
Ah, you are fixing endian issues. That was not clear to me from the commit message.
I don't know enough about how DT stores values in the blob. Is there type info? Can the DT core tell if a value in the blob is a u8 or a u32? It would be nice if it warned about reading a u8 from a u32 blob.
Anyway, this change still removes some bounds checking. Are they important? Do they need to be added back?
Thanks
Andrew
Re: [PATCH net-next v2 4/7] net: phy: mscc: read 'vsc8531,edge-slowdown' as an u32
Hi Andrew,
Quoted 10 lines · Andrew Lunn
Quoted 7 lines
Just to be sure, we're talking here about making sure the value stored in the DT is not bigger than the specified value (here an u8)? If so, that isn't the reason why I'm suggesting those two patches.
Without /bits 8/ in the DT property, whatever were the values I put in the property, I'd always get a 0. So I need to fix it either in the DT (but Rob does not really like it) or in the driver.
Hi Quentin
Quoted 8 lines
Ah, you are fixing endian issues. That was not clear to me from the commit message.
I don't know enough about how DT stores values in the blob. Is there type info? Can the DT core tell if a value in the blob is a u8 or a u32? It would be nice if it warned about reading a u8 from a u32 blob.
From my quick research, the lower bound checking is performed by of_property_read_u* functions but not the higher bound checking (the internal function of_find_property_value_of_size allows higher bound checking but it seems it's never used by those functions (see 0 in sz_max of of_property_read_variable_u*_array)).
sz_max is used by of_property_read_variable_u*_array to copy at a maximum of sz_max values in the output buffer. If sz_max is 0, it takes sz_min so it's an array of definite size.
So since sz_max is 0 for all calls to of_property_read_variable_u*_array by of_property_read_u*_array, we basically know we'll get a buffer of sz_min values but we don't actually make use of the higher bound checking of of_find_property_value_of_size.
We could enforce this higher bound check by, instead of setting sz_max to 0, setting sz_max to sz_min in calls to of_property_read_u*_array.
But I guess there is a reason for sz_max being 0. Rob, Richard (commit signer of this code) do you know why? Could you explain?
Quoted 3 lines
Anyway, this change still removes some bounds checking. Are they important? Do they need to be added back?
The edge-slowdown and the vddmac values are compared against a const array so we´re fine with those ones.
For the led-X-mode, I added a constant for supported modes that gets checked when retrieving the DT property. So we´re fine here too.
Quentin
Re: [PATCH net-next v2 4/7] net: phy: mscc: read 'vsc8531,edge-slowdown' as an u32 [UNSCANNED]
Quoted 28 lines · Quentin Schulz
Hi Andrew,
Quoted 10 lines · Andrew Lunn
Quoted 7 lines
Just to be sure, we're talking here about making sure the value stored in the DT is not bigger than the specified value (here an u8)? If so, that isn't the reason why I'm suggesting those two patches.
Without /bits 8/ in the DT property, whatever were the values I put in the property, I'd always get a 0. So I need to fix it either in the DT (but Rob does not really like it) or in the driver.
Hi Quentin
Quoted 8 lines
Ah, you are fixing endian issues. That was not clear to me from the commit message.
I don't know enough about how DT stores values in the blob. Is there type info? Can the DT core tell if a value in the blob is a u8 or a u32? It would be nice if it warned about reading a u8 from a u32 blob.
From my quick research, the lower bound checking is performed by
of_property_read_u* functions but not the higher bound checking (the internal functionof_find_property_value_of_sizeallows higher bound checking but it seems it's never used by those functions (see 0 insz_maxof of_property_read_variable_u*_array)).
Quoted 8 lines
sz_maxis used by of_property_read_variable_u*_array to copy at a maximum ofsz_maxvalues in the output buffer. Ifsz_maxis 0, it takessz_minso it's an array of definite size.
So sincesz_maxis 0 for all calls to of_property_read_variable_u*_array by of_property_read_u*_array, we basically know we'll get a buffer ofsz_minvalues but we don't actually make use of the higher bound checking ofof_find_property_value_of_size.
This was the original behaviour of the of_property_read_u*_array functions. If you look back at the of_property_read_u*_array implementations before my patch they passed max=0 to of_find_property_value_of_size.
To avoid duplicating code I reimplemented the of_property_read_u*_array to use the new of_property_read_variable_u*_array hence they pass sz_max=0 to preserve the original behaviour that max=0 to of_find_property_value_of_size, so that I didn't break any code that might depend on that.
Quoted 19 lines
We could enforce this higher bound check by, instead of setting
sz_maxto 0, settingsz_maxtosz_minin calls to of_property_read_u*_array.But I guess there is a reason for
sz_maxbeing 0. Rob, Richard (commit signer of this code) do you know why? Could you explain?Quoted 3 lines
Anyway, this change still removes some bounds checking. Are they important? Do they need to be added back?
The edge-slowdown and the vddmac values are compared against a const array so we´re fine with those ones.
For the led-X-mode, I added a constant for supported modes that gets checked when retrieving the DT property. So we´re fine here too.
Quentin
PATCH v2 5/7 net: phy: mscc: read 'vsc8531,led-%d-mode' as an u32
In reply to Quentin SchulzIn the DT binding, it is specified nowhere that 'vsc8531,led-%d-mode' is an u8, even though it's read as an u8 in the driver.
Let's update the driver to take into consideration that the 'vsc8531,led-%d-mode' property is of the default type u32.
---
added in v2 in lieu of the DT binding patch for adding /bits 8/ to the vsc8531,led-N-mode property
drivers/net/phy/mscc.c | 13 +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-)
drivers/net/phy/mscc.c +7 -6
@@ -122,7 +122,7 @@ enum rgmii_rx_clock_delay {struct vsc8531_private {int rate_magic;u16 supp_led_modes; -u8 leds_mode[MAX_LEDS ]; +u32 leds_mode[MAX_LEDS ];u8 nleds; };
@@ -414,19 +414,19 @@ static int vsc85xx_edge_rate_magic_get(struct phy_device *phydev)static int vsc85xx_dt_led_mode_get (struct phy_device *phydev,char *led, -u8 default_mode) +u32 default_mode) {struct vsc8531_private *priv = phydev->priv;struct device *dev = &phydev->mdio.dev;struct device_node *of_node = dev->of_node; -u8 led_mode; +u32 led_mode;int err;if (!of_node)return -ENODEV ; led_mode = default_mode; - err =of_property_read_u8 (of_node, led, &led_mode); + err =of_property_read_u32 (of_node, led, &led_mode);if (!err && !(BIT (led_mode) & priv->supp_led_modes)) {phydev_err (phydev,"DT %s invalid\n" , led);return -EINVAL ;
@@ -449,7 +449,8 @@ static int vsc85xx_dt_led_mode_get(struct phy_device *phydev, }#endif /* CONFIG_OF_MDIO */ -static int vsc85xx_dt_led_modes_get (struct phy_device *phydev,u8 *default_mode) +static int vsc85xx_dt_led_modes_get (struct phy_device *phydev, +u32 *default_mode) {struct vsc8531_private *priv = phydev->priv;char led_dt_prop[19 ];
@@ -656,7 +657,7 @@ static int vsc85xx_probe(struct phy_device *phydev) {struct vsc8531_private *vsc8531;int rate_magic; -u8 default_mode[2 ] = {VSC8531_LINK_1000_ACTIVITY , +u32 default_mode[2 ] = {VSC8531_LINK_1000_ACTIVITY ,VSC8531_LINK_100_ACTIVITY }; rate_magic =vsc85xx_edge_rate_magic_get (phydev);
Signature · 1 line
2.17.1
PATCH v2 6/7 dt-bindings: net: phy: mscc: vsc8531: remove compatible from required properties
In reply to Quentin SchulzCompatible isn't a required property for PHYs so let's remove it from the binding DT of the VSC8531 PHYs.
--- Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt | 5 ----- 1 file changed, 5 deletions(-)
Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt +0 -5
@@ -1,10 +1,5 @@ * Microsemi - vsc8531 Giga bit ethernet phy -Required properties: -- compatible : Should contain phy id as "ethernet-phy-idAAAA.BBBB" - The PHY device uses the binding described in - Documentation/devicetree/bindings/net/phy.txt - Optional properties: - vsc8531,vddmac : The vddmac in mV. Allowed values is listed in the first row of Table 1 (below).
Signature · 1 line
2.17.1
Andrew Lunn
maintainerRe: [PATCH net-next v2 6/7] dt-bindings: net: phy: mscc: vsc8531: remove compatible from required properties
Quoted 2 lines · Quentin Schulz
Compatible isn't a required property for PHYs so let's remove it from the binding DT of the VSC8531 PHYs.
Hi Quentin
It is actually a optional property. So you could move it into that section of the binding documentation. But removing it is also O.K.
Andrew
Re: [PATCH net-next v2 6/7] dt-bindings: net: phy: mscc: vsc8531: remove compatible from required properties
Hi Andrew,
Quoted 9 lines · Andrew Lunn
Quoted 2 lines · Quentin Schulz
Compatible isn't a required property for PHYs so let's remove it from the binding DT of the VSC8531 PHYs.
Hi Quentin
It is actually a optional property. So you could move it into that section of the binding documentation. But removing it is also O.K.
It's a property that is already defined inDocumentation/devicetree/bindings/net/phy.txt
I don't think it's actually useful to redefine it there (on the same principle that we don't redefine/re-explain the reg property).
What do we do? Do I put it in optional properties and refer to the aforementioned doc or do I just remove it as it's done in this patch?
Thanks,
Quentin
Andrew Lunn
maintainerRe: [PATCH net-next v2 6/7] dt-bindings: net: phy: mscc: vsc8531: remove compatible from required properties
Quoted 2 lines
What do we do? Do I put it in optional properties and refer to the aforementioned doc or do I just remove it as it's done in this patch?
Just remove it.
Andrew
PATCH v2 7/7 dt-bindings: net: phy: mscc: vsc8531: factorize vsc8531,led-N-mode
In reply to Quentin SchulzVSC8584 supports 4 LEDs while VSC8531 only supports 2. Let's factorize the documentation for LED mode properties and give the 4 default values (the first two being shared between VSC8531 and VSC8584).
--- .../devicetree/bindings/net/mscc-phy-vsc8531.txt | 16 +++++++++------- 1 file changed, 9 insertions(+), 7 deletions(-)
Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt +9 -7
@@ -22,14 +22,16 @@ Optional properties: 'vddmac'. Default value is 0%. Ref: Table:1 - Edge rate change (below). -- vsc8531,led-0-mode : LED mode. Specify how the LED[0] should behave. - Allowed values are define in +- vsc8531,led-[N]-mode : LED mode. Specify how the LED[N] should behave. + N depends on the number of LEDs supported by a + PHY. + Allowed values are defined in "include/dt-bindings/net/mscc-phy-vsc8531.h". - Default value is VSC8531_LINK_1000_ACTIVITY (1). -- vsc8531,led-1-mode : LED mode. Specify how the LED[1] should behave. - Allowed values are define in - "include/dt-bindings/net/mscc-phy-vsc8531.h". - Default value is VSC8531_LINK_100_ACTIVITY (2). + Default values are VSC8531_LINK_1000_ACTIVITY (1), + VSC8531_LINK_100_ACTIVITY (2), + VSC8531_LINK_ACTIVITY (0) and + VSC8531_DUPLEX_COLLISION (8). + Table: 1 - Edge rate change ----------------------------------------------------------------|
Signature · 1 line
2.17.1
David Miller
maintainerFrom: Quentin Schulz <[email protected]>
Date: Mon, 3 Sep 2018 10:48:47 +0200
Quoted 7 lines
LEDs modes are set the same way, except they are offset by 4 times the index of the LED.
Let's factorize all the code so that it's easier to add support for the 4 LEDs of the VSC8584 PHY.
Signed-off-by Quentin Schulz <[email protected]>
Entire series applied to net-next.
Please provide a proper "0/N ..." cover letter next time.
Thank you.
Hi David,
Quoted 6 lines · David Miller
From: Quentin Schulz <[email protected]>
Date: Mon, 3 Sep 2018 10:48:47 +0200Quoted 3 lines
LEDs modes are set the same way, except they are offset by 4 times the index of the LED.
Quoted 7 lines
Quoted 4 lines
Let's factorize all the code so that it's easier to add support for the 4 LEDs of the VSC8584 PHY.
Signed-off-by Quentin Schulz <[email protected]>Entire series applied to net-next.
Thanks!
Quoted 2 lines
Please provide a proper "0/N ..." cover letter next time.
Sure, will do.
Quentin