mmc: sunxi: Clarify new timing mode usage and implementation
Subsystems (2)
PATCH 1/1 mmc: sunxi: Clarify new timing mode usage and implementation
Newer sunxi mmc controller variants support what they call the "new timing mode". Support for this was implemented in two ways, according to the hardware that was seen at the time.
The first type retained the old timing mode, and both the clock and mmc controllers had switches to select which mode was used. Both switches had to be set to the same setting. This variant was denoted with the .has_timings_switch field in the sunxi_mmc_cfg structure. This hardware is only seen on the A83T.
The second type did away with the old timing mode. The clock controller no longer had the mode selection or clock delay setting bits. In some cases the mmc controller retained its mode selection bit, but this always needed to be set to the new mode, or instabilities would occur. In a few cases, such as the A64 and H6 eMMC controller, the mode selection bit is gone, but the controller still behaves like the new timing mode, requiring the module clock to be double the card clock in DDR transfer modes. This variant is denoted with the .needs_new_timings field.
This patch adds more comments explaining the two fields, as well as the possibly nonexistent mode switch in the mmc controller.
The .has_timings_switch is renamed to .ccu_has_timings_switch to clarify its meaning.
--- drivers/mmc/host/sunxi-mmc.c | 23 +++++++++++++++++------ 1 file changed, 17 insertions(+), 6 deletions(-)
drivers/mmc/host/sunxi-mmc.c +17 -6
@@ -258,11 +258,16 @@ struct sunxi_mmc_cfg {/* Does DATA0 needs to be masked while the clock is updated */ bool mask_data0; -/* hardware only supports new timing mode */ +/* +* hardware only supports new timing mode, either due to lack of +* a mode switch in the clock controller, or the mmc controller +* is permanently configured in the new timing mode, without the +* NTSR mode switch. +*/ bool needs_new_timings; -/* hardware can switch between old and new timing modes */ -bool has_timings_switch; +/* clock hardware can switch between old and new timing modes */ +bool ccu_has_timings_switch; };struct sunxi_mmc_host {
@@ -787,7 +792,7 @@ static int sunxi_mmc_clk_set_rate(struct sunxi_mmc_host *host, clock <<=1 ; } -if (host->use_new_timings && host->cfg->has_timings_switch) { +if (host->use_new_timings && host->cfg->ccu_has_timings_switch) { ret =sunxi_ccu_set_mmc_timing_mode (host->clk_mmc, true);if (ret) { dev_err(mmc_dev(mmc),
@@ -822,6 +827,12 @@ static int sunxi_mmc_clk_set_rate(struct sunxi_mmc_host *host,/* update card clock rate to account for internal divider */ rate /= div; +/* +* Configure the controller to use the new timing mode if needed. +* On controllers that only support the new timing mode, such as +* the eMMC controller on the A64, this register does not exist, +* and any writes to it are ignored. +*/ if (host->use_new_timings) {/* Don't touch the delay bits */ rval =mmc_readl (host,REG_SD_NTSR );
@@ -1145,7 +1156,7 @@ static const struct sunxi_mmc_cfg sun8i_a83t_emmc_cfg = { .idma_des_size_bits = 16, .clk_delays = sunxi_mmc_clk_delays, .can_calibrate = false, - .has_timings_switch = true, + .ccu_has_timings_switch = true, };static const struct sunxi_mmc_cfg sun9i_a80_cfg = {
@@ -1351,7 +1362,7 @@ static int sunxi_mmc_probe(struct platform_device *pdev) goto error_free_host; } -if (host->cfg->has_timings_switch) { +if (host->cfg->ccu_has_timings_switch) {/* * Supports both old and new timing modes. * Try setting the clk to new timing mode.
Signature · 1 line
2.19.0.rc1
PATCH 1/1 mmc: sunxi: Clarify new timing mode usage and implementation
Quoted 20 lines · Chen-Yu Tsai
Newer sunxi mmc controller variants support what they call the "new timing mode". Support for this was implemented in two ways, according to the hardware that was seen at the time.
The first type retained the old timing mode, and both the clock and mmc controllers had switches to select which mode was used. Both switches had to be set to the same setting. This variant was denoted with the .has_timings_switch field in the
sunxi_mmc_cfgstructure. This hardware is only seen on the A83T.The second type did away with the old timing mode. The clock controller no longer had the mode selection or clock delay setting bits. In some cases the mmc controller retained its mode selection bit, but this always needed to be set to the new mode, or instabilities would occur. In a few cases, such as the A64 and H6 eMMC controller, the mode selection bit is gone, but the controller still behaves like the new timing mode, requiring the module clock to be double the card clock in DDR transfer modes. This variant is denoted with the .needs_new_timings field.
Quoted 7 lines
This patch adds more comments explaining the two fields, as well as the possibly nonexistent mode switch in the mmc controller.
The .has_timings_switch is renamed to .ccu_has_timings_switch to clarify its meaning.
Signed-off-by Chen-Yu Tsai <[email protected]>
Thanks!
Maxime
Signature · 10 lines
Maxime Ripard, Bootlin Embedded Linux and Kernel engineering https://bootlin.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 833 bytes Desc: not available URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20180907/24241561/attachment.sig>
PATCH 1/1 mmc: sunxi: Clarify new timing mode usage and implementation
In reply to Chen-Yu TsaiQuoted 20 lines · Chen-Yu Tsai
Newer sunxi mmc controller variants support what they call the "new timing mode". Support for this was implemented in two ways, according to the hardware that was seen at the time.
The first type retained the old timing mode, and both the clock and mmc controllers had switches to select which mode was used. Both switches had to be set to the same setting. This variant was denoted with the .has_timings_switch field in the
sunxi_mmc_cfgstructure. This hardware is only seen on the A83T.The second type did away with the old timing mode. The clock controller no longer had the mode selection or clock delay setting bits. In some cases the mmc controller retained its mode selection bit, but this always needed to be set to the new mode, or instabilities would occur. In a few cases, such as the A64 and H6 eMMC controller, the mode selection bit is gone, but the controller still behaves like the new timing mode, requiring the module clock to be double the card clock in DDR transfer modes. This variant is denoted with the .needs_new_timings field.
Quoted 7 lines
This patch adds more comments explaining the two fields, as well as the possibly nonexistent mode switch in the mmc controller.
The .has_timings_switch is renamed to .ccu_has_timings_switch to clarify its meaning.
Signed-off-by Chen-Yu Tsai <[email protected]>
Applied for next, thanks!
Kind regards
Uffe
Quoted 71 lines
--- drivers/mmc/host/sunxi-mmc.c | 23 +++++++++++++++++------ 1 file changed, 17 insertions(+), 6 deletions(-)drivers/mmc/host/sunxi-mmc.c +17
-7@@ -258,11 +258,16 @@ struct sunxi_mmc_cfg {/* Does DATA0 needs to be masked while the clock is updated */ bool mask_data0; -/* hardware only supports new timing mode */ +/* +* hardware only supports new timing mode, either due to lack of +* a mode switch in the clock controller, or the mmc controller +* is permanently configured in the new timing mode, without the +* NTSR mode switch. +*/ bool needs_new_timings; -/* hardware can switch between old and new timing modes */ -bool has_timings_switch; +/* clock hardware can switch between old and new timing modes */ +bool ccu_has_timings_switch; };struct sunxi_mmc_host {@@ -787,7 +792,7 @@ static int sunxi_mmc_clk_set_rate(struct sunxi_mmc_host *host, clock <<=1 ; } -if (host->use_new_timings && host->cfg->has_timings_switch) { +if (host->use_new_timings && host->cfg->ccu_has_timings_switch) { ret =sunxi_ccu_set_mmc_timing_mode (host->clk_mmc, true);if (ret) { dev_err(mmc_dev(mmc),@@ -822,6 +827,12 @@ static int sunxi_mmc_clk_set_rate(struct sunxi_mmc_host *host,/* update card clock rate to account for internal divider */ rate /= div; +/* +* Configure the controller to use the new timing mode if needed. +* On controllers that only support the new timing mode, such as +* the eMMC controller on the A64, this register does not exist, +* and any writes to it are ignored. +*/ if (host->use_new_timings) {/* Don't touch the delay bits */ rval =mmc_readl (host,REG_SD_NTSR );@@ -1145,7 +1156,7 @@ static const struct sunxi_mmc_cfg sun8i_a83t_emmc_cfg = { .idma_des_size_bits = 16, .clk_delays = sunxi_mmc_clk_delays, .can_calibrate = false, - .has_timings_switch = true, + .ccu_has_timings_switch = true, };static const struct sunxi_mmc_cfg sun9i_a80_cfg = {@@ -1351,7 +1362,7 @@ static int sunxi_mmc_probe(struct platform_device *pdev) goto error_free_host; } -if (host->cfg->has_timings_switch) { +if (host->cfg->ccu_has_timings_switch) {/* * Supports both old and new timing modes. * Try setting the clk to new timing mode. -- 2.19.0.rc1