V4L2 fwnode rework; support for default configuration
Subsystems (27)
Sakari Ailus
maintainerv3 cover V4L2 fwnode rework; support for default configuration
Hello everyone,
I've long thought the V4L2 fwnode framework requires some work (it's buggy and it does not adequately serve common needs). This set should address in particular these matters:
- Most devices support a particular media bus type but the V4L2 fwnode framework was not able to use such information, but instead tried to guess the bus type with varying levels of success while drivers generally ignored the results. This patchset makes that possible --- setting a bus type enables parsing configuration for only that bus. Failing that check results in returning -ENXIO to be returned.
- Support specifying default configuration. If the endpoint has no configuration, the defaults set by the driver (as documented in DT bindings) will prevail. Any available configuration will still be read from the endpoint as one could expect. A common use case for this is e.g. the number of CSI-2 lanes. Few devices support lane mapping, and default 1:1 mapping is provided in absence of a valid default or configuration read OF.
- Debugging information is greatly improved.
- Recognition of the differences between CSI-2 D-PHY and C-PHY. All currently supported hardware (or at least drivers) is D-PHY only, so this change is still easy.
The smiapp driver is converted to use the new functionality. This patchset does not address remaining issues such as supporting setting defaults for e.g. bridge drivers with multiple ports, but with Steve Longerbeam's patchset we're much closer to that goal. I've rebased this set on top of Steve's. Albeit the two deal with the same files, there were only a few trivial conflicts.
Note that I've only tested parsing endpoints for the CSI-2 bus (no parallel IF hardware). Jacopo has tested an earlier version of the set with a few changes to the parallel bus handling compared to this one.
Comments are welcome.
I've pushed the patches (including Steve's) here:
<URL:https://git.linuxtv.org/sailus/media_tree.git/log/?h=v4l2-fwnode-next>
since v1:
- Rebase it all on current media tree master --- there was a conflict in drivers/media/platform/qcom/camss/camss.c in Steve's patch "media:
platform: Switch to v4l2_async_notifier_add_subdev"; I hope the resolution was fine.
- Default to Bt.656 bus in guessing the bus type if no properties suggesting otherwise are set. In v1 and error was returned, which would have been troublesome for the existing drivers.
- Set the bus_type field to zero (i.e. guess) for existing callers of v4l2_fwnode_endpoint_(alloc_)parse.
- Improved documentation for v4l2_fwnode_endpoint_parse and v4l2_fwnode_endpoint_alloc_parse.
since v2:
- Rename V4L2_MBUS_CSI2 to V4L2_MBUS_CSI2_DPHY also in drivers/gpu/ipu-v3/ipu-csi.c.
- Use 0 instead of V4L2_MBUS_UNKNOWN in v4l2_async_notifier_fwnode_parse_endpoint(). This is partially due to V4L2_MBUS_UNKNOWN being introduced after the change is done.
- Initialise bus_type to zero in quite a few V4L2 fwnode endpoints in drivers/staging/media/imx/imx-media-csi.c (thanks to Steve for the changes).
Sakari Ailus (23):
v4l: fwnode: Add debug prints for V4L2 endpoint property parsing
v4l: fwnode: Use fwnode_graph_for_each_endpoint
v4l: fwnode: The CSI-2 clock is continuous if it's not non-continuous
dt-bindings: media: Specify bus type for MIPI D-PHY, others,
explicitly
v4l: fwnode: Add definitions for CSI-2 D-PHY, parallel and Bt.656
busses
v4l: mediabus: Recognise CSI-2 D-PHY and C-PHY
v4l: fwnode: Let the caller provide V4L2 fwnode endpoint
v4l: fwnode: Detect bus type correctly
v4l: fwnode: Make use of newly specified bus types
v4l: fwnode: Read lane inversion information despite lane numbering
v4l: fwnode: Only assign configuration if there is no error
v4l: fwnode: Support driver-defined lane mapping defaults
v4l: fwnode: Support default CSI-2 lane mapping for drivers
v4l: fwnode: Parse the graph endpoint as last
v4l: fwnode: Use default parallel flags
v4l: fwnode: Initialise the V4L2 fwnode endpoints to zero
v4l: fwnode: Only zero the struct if bus type is set to
V4L2_MBUS_UNKNOWN
v4l: fwnode: Use media bus type for bus parser selection
v4l: fwnode: Print bus type
v4l: fwnode: Use V4L2 fwnode endpoint media bus type if set
v4l: fwnode: Support parsing of CSI-2 C-PHY endpoints
v4l: fwnode: Update V4L2 fwnode endpoint parsing documentation
smiapp: Query the V4L2 endpoint for a specific bus type
.../devicetree/bindings/media/video-interfaces.txt | 4 +- drivers/gpu/ipu-v3/ipu-csi.c | 6 +- drivers/media/i2c/adv7180.c | 2 +- drivers/media/i2c/adv7604.c | 2 +- drivers/media/i2c/mt9v032.c | 2 +- drivers/media/i2c/ov2659.c | 14 +- drivers/media/i2c/ov5640.c | 4 +- drivers/media/i2c/ov5645.c | 2 +- drivers/media/i2c/ov5647.c | 2 +- drivers/media/i2c/ov7251.c | 4 +- drivers/media/i2c/ov7670.c | 2 +- drivers/media/i2c/s5c73m3/s5c73m3-core.c | 4 +- drivers/media/i2c/s5k5baf.c | 6 +- drivers/media/i2c/s5k6aa.c | 2 +- drivers/media/i2c/smiapp/smiapp-core.c | 34 +- drivers/media/i2c/soc_camera/ov5642.c | 2 +- drivers/media/i2c/tc358743.c | 28 +- drivers/media/i2c/tda1997x.c | 2 +- drivers/media/i2c/tvp514x.c | 2 +- drivers/media/i2c/tvp5150.c | 2 +- drivers/media/i2c/tvp7002.c | 2 +- drivers/media/pci/intel/ipu3/ipu3-cio2.c | 2 +- drivers/media/platform/am437x/am437x-vpfe.c | 2 +- drivers/media/platform/atmel/atmel-isc.c | 3 +- drivers/media/platform/atmel/atmel-isi.c | 2 +- drivers/media/platform/cadence/cdns-csi2rx.c | 4 +- drivers/media/platform/cadence/cdns-csi2tx.c | 4 +- drivers/media/platform/davinci/vpif_capture.c | 2 +- drivers/media/platform/exynos4-is/media-dev.c | 2 +- drivers/media/platform/exynos4-is/mipi-csis.c | 2 +- drivers/media/platform/marvell-ccic/mcam-core.c | 4 +- drivers/media/platform/marvell-ccic/mmp-driver.c | 2 +- drivers/media/platform/omap3isp/isp.c | 2 +- drivers/media/platform/pxa_camera.c | 4 +- drivers/media/platform/rcar-vin/rcar-csi2.c | 4 +- drivers/media/platform/renesas-ceu.c | 3 +- drivers/media/platform/soc_camera/soc_mediabus.c | 2 +- drivers/media/platform/stm32/stm32-dcmi.c | 4 +- drivers/media/platform/ti-vpe/cal.c | 2 +- drivers/media/v4l2-core/v4l2-fwnode.c | 508 ++++++++++++++++----- drivers/staging/media/imx/imx-media-csi.c | 10 +- drivers/staging/media/imx/imx6-mipi-csi2.c | 2 +- drivers/staging/media/imx074/imx074.c | 2 +- include/media/v4l2-fwnode.h | 60 ++- include/media/v4l2-mediabus.h | 8 +- 45 files changed, 542 insertions(+), 226 deletions(-)
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 1/23 v4l: fwnode: Add debug prints for V4L2 endpoint property parsing
Print debug info as standard V4L2 endpoint are parsed.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 108 ++++++++++++++++++++++++++-------- 1 file changed, 85 insertions(+), 23 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +85 -23
@@ -66,6 +66,7 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, lanes_used |=BIT (array[i]); bus->data_lanes[i] = array[i]; +pr_debug ("lane %u position %u\n" , i, array[i]); } rval = fwnode_property_read_u32_array(fwnode,
@@ -82,8 +83,13 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,"lane-polarities" , array, 1 + bus->num_data_lanes); -for (i =0 ; i <1 + bus->num_data_lanes; i++) +for (i =0 ; i <1 + bus->num_data_lanes; i++) { bus->lane_polarities[i] = array[i]; +pr_debug ("lane %u polarity %sinverted" , + i, array[i] ?"" :"not " ); + } + }else { +pr_debug ("no lane polarities defined, assuming not inverted\n" ); } }
@@ -95,12 +101,15 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, bus->clock_lane = v; have_clk_lane = true; +pr_debug ("clock lane position %u\n" , v); } -if (fwnode_property_present (fwnode,"clock-noncontinuous" )) +if (fwnode_property_present (fwnode,"clock-noncontinuous" )) { flags |=V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK ; -else if (have_clk_lane || bus->num_data_lanes >0 ) +pr_debug ("non-continuous clock\n" ); + }else if (have_clk_lane || bus->num_data_lanes >0 ) { flags |=V4L2_MBUS_CSI2_CONTINUOUS_CLOCK ; + } bus->flags = flags; vep->bus_type =V4L2_MBUS_CSI2 ;
@@ -115,48 +124,69 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(unsigned int flags =0 ;u32 v; -if (!fwnode_property_read_u32 (fwnode,"hsync-active" , &v)) +if (!fwnode_property_read_u32 (fwnode,"hsync-active" , &v)) { flags |= v ?V4L2_MBUS_HSYNC_ACTIVE_HIGH :V4L2_MBUS_HSYNC_ACTIVE_LOW ; +pr_debug ("hsync-active %s\n" , v ?"high" :"low" ); + } -if (!fwnode_property_read_u32 (fwnode,"vsync-active" , &v)) +if (!fwnode_property_read_u32 (fwnode,"vsync-active" , &v)) { flags |= v ?V4L2_MBUS_VSYNC_ACTIVE_HIGH :V4L2_MBUS_VSYNC_ACTIVE_LOW ; +pr_debug ("vsync-active %s\n" , v ?"high" :"low" ); + } -if (!fwnode_property_read_u32 (fwnode,"field-even-active" , &v)) +if (!fwnode_property_read_u32 (fwnode,"field-even-active" , &v)) { flags |= v ?V4L2_MBUS_FIELD_EVEN_HIGH :V4L2_MBUS_FIELD_EVEN_LOW ; +pr_debug ("field-even-active %s\n" , v ?"high" :"low" ); + } +if (flags) vep->bus_type =V4L2_MBUS_PARALLEL ;else vep->bus_type =V4L2_MBUS_BT656 ; -if (!fwnode_property_read_u32 (fwnode,"pclk-sample" , &v)) +if (!fwnode_property_read_u32 (fwnode,"pclk-sample" , &v)) { flags |= v ?V4L2_MBUS_PCLK_SAMPLE_RISING :V4L2_MBUS_PCLK_SAMPLE_FALLING ; +pr_debug ("pclk-sample %s\n" , v ?"high" :"low" ); + } -if (!fwnode_property_read_u32 (fwnode,"data-active" , &v)) +if (!fwnode_property_read_u32 (fwnode,"data-active" , &v)) { flags |= v ?V4L2_MBUS_DATA_ACTIVE_HIGH :V4L2_MBUS_DATA_ACTIVE_LOW ; +pr_debug ("data-active %s\n" , v ?"high" :"low" ); + } -if (fwnode_property_present (fwnode,"slave-mode" )) +if (fwnode_property_present (fwnode,"slave-mode" )) { +pr_debug ("slave mode\n" ); flags |=V4L2_MBUS_SLAVE ; -else + }else { flags |=V4L2_MBUS_MASTER ; + } -if (!fwnode_property_read_u32 (fwnode,"bus-width" , &v)) +if (!fwnode_property_read_u32 (fwnode,"bus-width" , &v)) { bus->bus_width = v; +pr_debug ("bus-width %u\n" , v); + } -if (!fwnode_property_read_u32 (fwnode,"data-shift" , &v)) +if (!fwnode_property_read_u32 (fwnode,"data-shift" , &v)) { bus->data_shift = v; +pr_debug ("data-shift %u\n" , v); + } -if (!fwnode_property_read_u32 (fwnode,"sync-on-green-active" , &v)) +if (!fwnode_property_read_u32 (fwnode,"sync-on-green-active" , &v)) { flags |= v ?V4L2_MBUS_VIDEO_SOG_ACTIVE_HIGH :V4L2_MBUS_VIDEO_SOG_ACTIVE_LOW ; +pr_debug ("sync-on-green-active %s\n" , v ?"high" :"low" ); + } -if (!fwnode_property_read_u32 (fwnode,"data-enable-active" , &v)) +if (!fwnode_property_read_u32 (fwnode,"data-enable-active" , &v)) { flags |= v ?V4L2_MBUS_DATA_ENABLE_HIGH :V4L2_MBUS_DATA_ENABLE_LOW ; +pr_debug ("data-enable-active %s\n" , v ?"high" :"low" ); + } bus->flags = flags;
@@ -170,17 +200,25 @@ v4l2_fwnode_endpoint_parse_csi1_bus(struct fwnode_handle *fwnode,struct v4l2_fwnode_bus_mipi_csi1 *bus = &vep->bus.mipi_csi1;u32 v; -if (!fwnode_property_read_u32 (fwnode,"clock-inv" , &v)) +if (!fwnode_property_read_u32 (fwnode,"clock-inv" , &v)) { bus->clock_inv = v; +pr_debug ("clock-inv %u\n" , v); + } -if (!fwnode_property_read_u32 (fwnode,"strobe" , &v)) +if (!fwnode_property_read_u32 (fwnode,"strobe" , &v)) { bus->strobe = v; +pr_debug ("strobe %u\n" , v); + } -if (!fwnode_property_read_u32 (fwnode,"data-lanes" , &v)) +if (!fwnode_property_read_u32 (fwnode,"data-lanes" , &v)) { bus->data_lane = v; +pr_debug ("data-lanes %u\n" , v); + } -if (!fwnode_property_read_u32 (fwnode,"clock-lanes" , &v)) +if (!fwnode_property_read_u32 (fwnode,"clock-lanes" , &v)) { bus->clock_lane = v; +pr_debug ("clock-lanes %u\n" , v); + }if (bus_type ==V4L2_FWNODE_BUS_TYPE_CCP2 ) vep->bus_type =V4L2_MBUS_CCP2 ;
@@ -188,12 +226,14 @@ v4l2_fwnode_endpoint_parse_csi1_bus(struct fwnode_handle *fwnode, vep->bus_type =V4L2_MBUS_CSI1 ; } -int v4l2_fwnode_endpoint_parse (struct fwnode_handle *fwnode, -struct v4l2_fwnode_endpoint *vep) +static int __v4l2_fwnode_endpoint_parse (struct fwnode_handle *fwnode, +struct v4l2_fwnode_endpoint *vep) {u32 bus_type =0 ;int rval; +pr_debug ("===== begin V4L2 endpoint properties\n" ); +fwnode_graph_parse_endpoint (fwnode, &vep->base);/* Zero fields from bus_type to until the end */
@@ -214,16 +254,30 @@ int v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,if (vep->bus.mipi_csi2.flags ==0 )v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep); -return 0 ; +break ;case V4L2_FWNODE_BUS_TYPE_CCP2 :case V4L2_FWNODE_BUS_TYPE_CSI1 :v4l2_fwnode_endpoint_parse_csi1_bus (fwnode, vep, bus_type); -return 0 ; +break ;default :pr_warn ("unsupported bus type %u\n" , bus_type);return -EINVAL ; } + +return 0 ; +} + +int v4l2_fwnode_endpoint_parse (struct fwnode_handle *fwnode, +struct v4l2_fwnode_endpoint *vep) +{ +int ret; + + ret =__v4l2_fwnode_endpoint_parse (fwnode, vep); + +pr_debug ("===== end V4L2 endpoint properties\n" ); + +return ret; }EXPORT_SYMBOL_GPL (v4l2_fwnode_endpoint_parse);
@@ -247,13 +301,15 @@ struct v4l2_fwnode_endpoint *v4l2_fwnode_endpoint_alloc_parse(if (!vep)return ERR_PTR (-ENOMEM ); - rval =v4l2_fwnode_endpoint_parse (fwnode, vep); + rval =__v4l2_fwnode_endpoint_parse (fwnode, vep);if (rval <0 ) goto out_err; rval =fwnode_property_read_u64_array (fwnode,"link-frequencies" ,NULL ,0 );if (rval >0 ) { +unsigned int i; + vep->link_frequencies =kmalloc_array (rval,sizeof (*vep->link_frequencies),GFP_KERNEL );
@@ -269,8 +325,14 @@ struct v4l2_fwnode_endpoint *v4l2_fwnode_endpoint_alloc_parse( vep->nr_of_link_frequencies);if (rval <0 ) goto out_err; + +for (i =0 ; i < vep->nr_of_link_frequencies; i++) +pr_info ("link-frequencies %u value %llu\n" , i, + vep->link_frequencies[i]); } +pr_debug ("===== end V4L2 endpoint properties\n" ); +return vep; out_err:
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 2/23 v4l: fwnode: Use fwnode_graph_for_each_endpoint
In reply to Sakari AilusUse fwnode_graph_for_each_endpoint iterator for better readability.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +1 -2
@@ -456,8 +456,7 @@ static int __v4l2_async_notifier_parse_fwnode_endpoints(if (WARN_ON (asd_struct_size <sizeof (struct v4l2_async_subdev )))return -EINVAL ; -for (fwnode =NULL ; (fwnode =fwnode_graph_get_next_endpoint ( -dev_fwnode (dev), fwnode)); ) { +fwnode_graph_for_each_endpoint (dev_fwnode (dev), fwnode) {struct fwnode_handle *dev_fwnode;bool is_available;
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 3/23 v4l: fwnode: The CSI-2 clock is continuous if it's not non-continuous
In reply to Sakari AilusThe continuous clock flag was only set if there was a clock or data lanes. This isn't needed as such a configuration is invalid to begin with. Always set the continuous clock flag if the non-continuous property is not found.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/media/v4l2-core/v4l2-fwnode.c +1 -1
@@ -107,7 +107,7 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,if (fwnode_property_present (fwnode,"clock-noncontinuous" )) { flags |=V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK ;pr_debug ("non-continuous clock\n" ); - }else if (have_clk_lane || bus->num_data_lanes >0 ) { + }else { flags |=V4L2_MBUS_CSI2_CONTINUOUS_CLOCK ; }
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 4/23 dt-bindings: media: Specify bus type for MIPI D-PHY, others, explicitly
In reply to Sakari AilusAllow specifying the bus type explicitly for MIPI D-PHY, parallel and Bt.656 busses. This is useful for devices that can make use of different bus types. There are CSI-2 transmitters and receivers but the PHY selection needs to be made between C-PHY and D-PHY; many devices also support parallel and Bt.656 interfaces but the means to pass that information to software wasn't there.
Autodetection (value 0) is removed as an option as the property could be simply omitted in that case.
--- Documentation/devicetree/bindings/media/video-interfaces.txt | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/media/video-interfaces.txt +3 -1
@@ -100,10 +100,12 @@ Optional endpoint properties slave device (data source) by the master device (data sink). In the master mode the data source device is also the source of the synchronization signals. - bus-type: data bus type. Possible values are: - 0 - autodetect based on other properties (MIPI CSI-2 D-PHY, parallel or Bt656) 1 - MIPI CSI-2 C-PHY 2 - MIPI CSI1 3 - CCP2 + 4 - MIPI CSI-2 D-PHY + 5 - Parallel + 6 - Bt.656 - bus-width: number of data lines actively used, valid for the parallel busses. - data-shift: on the parallel data busses, if bus-width is used to specify the number of data lines, data-shift can be used to specify which data lines are
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 5/23 v4l: fwnode: Add definitions for CSI-2 D-PHY, parallel and Bt.656 busses
In reply to Sakari AilusAdd definitions corresponding to DT bindings to the CSI-2 D-PHY, parallel and Bt.656 busses.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 3 +++ 1 file changed, 3 insertions(+)
drivers/media/v4l2-core/v4l2-fwnode.c +3 -0
@@ -36,6 +36,9 @@ enum v4l2_fwnode_bus_type {V4L2_FWNODE_BUS_TYPE_CSI2_CPHY ,V4L2_FWNODE_BUS_TYPE_CSI1 ,V4L2_FWNODE_BUS_TYPE_CCP2 , +V4L2_FWNODE_BUS_TYPE_CSI2_DPHY , +V4L2_FWNODE_BUS_TYPE_PARALLEL , +V4L2_FWNODE_BUS_TYPE_BT656 , NR_OF_V4L2_FWNODE_BUS_TYPE, };
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 6/23 v4l: mediabus: Recognise CSI-2 D-PHY and C-PHY
In reply to Sakari AilusThe CSI-2 bus may use either D-PHY or C-PHY. Make this visible in media bus enum.
--- drivers/gpu/ipu-v3/ipu-csi.c | 6 +++--- drivers/media/i2c/adv7180.c | 2 +- drivers/media/i2c/ov5640.c | 4 ++-- drivers/media/i2c/ov5645.c | 2 +- drivers/media/i2c/ov7251.c | 4 ++-- drivers/media/i2c/s5c73m3/s5c73m3-core.c | 2 +- drivers/media/i2c/s5k5baf.c | 4 ++-- drivers/media/i2c/s5k6aa.c | 2 +- drivers/media/i2c/smiapp/smiapp-core.c | 2 +- drivers/media/i2c/soc_camera/ov5642.c | 2 +- drivers/media/i2c/tc358743.c | 4 ++-- drivers/media/pci/intel/ipu3/ipu3-cio2.c | 2 +- drivers/media/platform/cadence/cdns-csi2rx.c | 2 +- drivers/media/platform/cadence/cdns-csi2tx.c | 2 +- drivers/media/platform/marvell-ccic/mcam-core.c | 4 ++-- drivers/media/platform/marvell-ccic/mmp-driver.c | 2 +- drivers/media/platform/omap3isp/isp.c | 2 +- drivers/media/platform/pxa_camera.c | 2 +- drivers/media/platform/rcar-vin/rcar-csi2.c | 2 +- drivers/media/platform/soc_camera/soc_mediabus.c | 2 +- drivers/media/platform/stm32/stm32-dcmi.c | 2 +- drivers/media/platform/ti-vpe/cal.c | 2 +- drivers/media/v4l2-core/v4l2-fwnode.c | 2 +- drivers/staging/media/imx/imx-media-csi.c | 2 +- drivers/staging/media/imx/imx6-mipi-csi2.c | 2 +- drivers/staging/media/imx074/imx074.c | 2 +- include/media/v4l2-mediabus.h | 6 ++++-- 27 files changed, 37 insertions(+), 35 deletions(-)
drivers/gpu/ipu-v3/ipu-csi.c +3 -3
@@ -232,7 +232,7 @@ static int mbus_code_to_bus_cfg(struct ipu_csi_bus_config *cfg, u32 mbus_code,case MEDIA_BUS_FMT_BGR565_2X8_LE :case MEDIA_BUS_FMT_RGB565_2X8_BE :case MEDIA_BUS_FMT_RGB565_2X8_LE : -if (mbus_type ==V4L2_MBUS_CSI2 ) +if (mbus_type ==V4L2_MBUS_CSI2_DPHY ) cfg->data_fmt =CSI_SENS_CONF_DATA_FMT_RGB565 ;else cfg->data_fmt =CSI_SENS_CONF_DATA_FMT_BAYER ;
@@ -359,7 +359,7 @@ static int fill_csi_bus_cfg(struct ipu_csi_bus_config *csicfg,else csicfg->clk_mode =IPU_CSI_CLK_MODE_CCIR656_PROGRESSIVE ;break ; -case V4L2_MBUS_CSI2 : +case V4L2_MBUS_CSI2_DPHY :/* * MIPI CSI-2 requires non gated clock mode, all other * parameters are not applicable for MIPI CSI-2 bus.
@@ -611,7 +611,7 @@ int ipu_csi_set_mipi_datatype(struct ipu_csi *csi, u32 vc,if (vc >3 )return -EINVAL ; - ret =mbus_code_to_bus_cfg (&cfg, mbus_fmt->code,V4L2_MBUS_CSI2 ); + ret =mbus_code_to_bus_cfg (&cfg, mbus_fmt->code,V4L2_MBUS_CSI2_DPHY );if (ret <0 )return ret;
drivers/media/i2c/adv7180.c +1 -1
@@ -761,7 +761,7 @@ static int adv7180_g_mbus_config(struct v4l2_subdev *sd,struct adv7180_state *state =to_state (sd);if (state->chip_info->flags &ADV7180_FLAG_MIPI_CSI2 ) { - cfg->type =V4L2_MBUS_CSI2 ; + cfg->type =V4L2_MBUS_CSI2_DPHY ; cfg->flags =V4L2_MBUS_CSI2_1_LANE |V4L2_MBUS_CSI2_CHANNEL_0 |V4L2_MBUS_CSI2_CONTINUOUS_CLOCK ;
drivers/media/i2c/ov5640.c +2 -2
@@ -1787,7 +1787,7 @@ static int ov5640_set_power(struct ov5640_dev *sensor, bool on)if (ret) goto power_off; -if (sensor->ep.bus_type ==V4L2_MBUS_CSI2 ) { +if (sensor->ep.bus_type ==V4L2_MBUS_CSI2_DPHY ) {/* * start streaming briefly followed by stream off in * order to coax the clock lane into LP-11 state.
@@ -2557,7 +2557,7 @@ static int ov5640_s_stream(struct v4l2_subdev *sd, int enable) sensor->pending_fmt_change = false; } -if (sensor->ep.bus_type ==V4L2_MBUS_CSI2 ) +if (sensor->ep.bus_type ==V4L2_MBUS_CSI2_DPHY ) ret =ov5640_set_stream_mipi (sensor, enable);else ret =ov5640_set_stream_dvp (sensor, enable);
drivers/media/i2c/ov5645.c +1 -1
@@ -1127,7 +1127,7 @@ static int ov5645_probe(struct i2c_client *client,return ret; } -if (ov5645->ep.bus_type !=V4L2_MBUS_CSI2 ) { +if (ov5645->ep.bus_type !=V4L2_MBUS_CSI2_DPHY ) {dev_err (dev,"invalid bus type, must be CSI2\n" );return -EINVAL ; }
drivers/media/i2c/ov7251.c +2 -2
@@ -1279,9 +1279,9 @@ static int ov7251_probe(struct i2c_client *client)return ret; } -if (ov7251->ep.bus_type !=V4L2_MBUS_CSI2 ) { +if (ov7251->ep.bus_type !=V4L2_MBUS_CSI2_DPHY ) {dev_err (dev,"invalid bus type (%u), must be CSI2 (%u)\n" , - ov7251->ep.bus_type,V4L2_MBUS_CSI2 ); + ov7251->ep.bus_type,V4L2_MBUS_CSI2_DPHY );return -EINVAL ; }
drivers/media/i2c/s5c73m3/s5c73m3-core.c +1 -1
@@ -1644,7 +1644,7 @@ static int s5c73m3_get_platform_data(struct s5c73m3 *state)if (ret)return ret; -if (ep.bus_type !=V4L2_MBUS_CSI2 ) { +if (ep.bus_type !=V4L2_MBUS_CSI2_DPHY ) {dev_err (dev,"unsupported bus type\n" );return -EINVAL ; }
drivers/media/i2c/s5k5baf.c +2 -2
@@ -766,7 +766,7 @@ static int s5k5baf_hw_set_video_bus(struct s5k5baf *state) {u16 en_pkts; -if (state->bus_type ==V4L2_MBUS_CSI2 ) +if (state->bus_type ==V4L2_MBUS_CSI2_DPHY ) en_pkts =EN_PACKETS_CSI2 ;else en_pkts =0 ;
@@ -1875,7 +1875,7 @@ static int s5k5baf_parse_device_node(struct s5k5baf *state, struct device *dev) state->bus_type = ep.bus_type;switch (state->bus_type) { -case V4L2_MBUS_CSI2 : +case V4L2_MBUS_CSI2_DPHY : state->nlanes = ep.bus.mipi_csi2.num_data_lanes;break ;case V4L2_MBUS_PARALLEL :
drivers/media/i2c/s5k6aa.c +1 -1
@@ -688,7 +688,7 @@ static int s5k6aa_configure_video_bus(struct s5k6aa *s5k6aa,* but there is nothing indicating how to switch between both * in the datasheet. For now default BT.601 interface is assumed. */ -if (bus_type ==V4L2_MBUS_CSI2 ) +if (bus_type ==V4L2_MBUS_CSI2_DPHY ) cfg = nlanes;else if (bus_type !=V4L2_MBUS_PARALLEL )return -EINVAL ;
drivers/media/i2c/smiapp/smiapp-core.c +1 -1
@@ -2784,7 +2784,7 @@ static struct smiapp_hwconfig *smiapp_get_hwconfig(struct device *dev) goto out_err;switch (bus_cfg->bus_type) { -case V4L2_MBUS_CSI2 : +case V4L2_MBUS_CSI2_DPHY : hwcfg->csi_signalling_mode =SMIAPP_CSI_SIGNALLING_MODE_CSI2 ; hwcfg->lanes = bus_cfg->bus.mipi_csi2.num_data_lanes;break ;
drivers/media/i2c/soc_camera/ov5642.c +1 -1
@@ -913,7 +913,7 @@ static int ov5642_get_selection(struct v4l2_subdev *sd,static int ov5642_g_mbus_config (struct v4l2_subdev *sd,struct v4l2_mbus_config *cfg) { - cfg->type =V4L2_MBUS_CSI2 ; + cfg->type =V4L2_MBUS_CSI2_DPHY ; cfg->flags =V4L2_MBUS_CSI2_2_LANE |V4L2_MBUS_CSI2_CHANNEL_0 |V4L2_MBUS_CSI2_CONTINUOUS_CLOCK ;
drivers/media/i2c/tc358743.c +2 -2
@@ -1607,7 +1607,7 @@ static int tc358743_g_mbus_config(struct v4l2_subdev *sd, {struct tc358743_state *state =to_state (sd); - cfg->type =V4L2_MBUS_CSI2 ; + cfg->type =V4L2_MBUS_CSI2_DPHY ;/* Support for non-continuous CSI-2 clock is missing in the driver */ cfg->flags =V4L2_MBUS_CSI2_CONTINUOUS_CLOCK ;
@@ -1922,7 +1922,7 @@ static int tc358743_probe_of(struct tc358743_state *state) goto put_node; } -if (endpoint->bus_type !=V4L2_MBUS_CSI2 || +if (endpoint->bus_type !=V4L2_MBUS_CSI2_DPHY || endpoint->bus.mipi_csi2.num_data_lanes ==0 || endpoint->nr_of_link_frequencies ==0 ) {dev_err (dev,"missing CSI-2 properties in endpoint\n" );
drivers/media/pci/intel/ipu3/ipu3-cio2.c +1 -1
@@ -1482,7 +1482,7 @@ static int cio2_fwnode_parse(struct device *dev,struct sensor_async_subdev *s_asd = container_of(asd, struct sensor_async_subdev, asd); -if (vep->bus_type !=V4L2_MBUS_CSI2 ) { +if (vep->bus_type !=V4L2_MBUS_CSI2_DPHY ) {dev_err (dev,"Only CSI2 bus type is currently supported\n" );return -EINVAL ; }
drivers/media/platform/cadence/cdns-csi2rx.c +1 -1
@@ -378,7 +378,7 @@ static int csi2rx_parse_dt(struct csi2rx_priv *csi2rx)return ret; } -if (v4l2_ep.bus_type !=V4L2_MBUS_CSI2 ) { +if (v4l2_ep.bus_type !=V4L2_MBUS_CSI2_DPHY ) {dev_err (csi2rx->dev,"Unsupported media bus type: 0x%x\n" , v4l2_ep.bus_type);of_node_put (ep);
drivers/media/platform/cadence/cdns-csi2tx.c +1 -1
@@ -446,7 +446,7 @@ static int csi2tx_check_lanes(struct csi2tx_priv *csi2tx) goto out; } -if (v4l2_ep.bus_type !=V4L2_MBUS_CSI2 ) { +if (v4l2_ep.bus_type !=V4L2_MBUS_CSI2_DPHY ) {dev_err (csi2tx->dev,"Unsupported media bus type: 0x%x\n" , v4l2_ep.bus_type); ret = -EINVAL ;
drivers/media/platform/marvell-ccic/mcam-core.c +2 -2
@@ -794,7 +794,7 @@ static void mcam_ctlr_image(struct mcam_camera *cam)/* * This field controls the generation of EOF(DVP only) */ -if (cam->bus_type !=V4L2_MBUS_CSI2 ) +if (cam->bus_type !=V4L2_MBUS_CSI2_DPHY )mcam_reg_set_bit (cam,REG_CTRL0 ,C0_EOF_VSYNC |C0_VEDGE_CTRL ); }
@@ -1023,7 +1023,7 @@ static int mcam_read_setup(struct mcam_camera *cam) cam->calc_dphy (cam);cam_dbg (cam,"camera: DPHY sets: dphy3=0x%x, dphy5=0x%x, dphy6=0x%x\n" , cam->dphy[0 ], cam->dphy[1 ], cam->dphy[2 ]); -if (cam->bus_type ==V4L2_MBUS_CSI2 ) +if (cam->bus_type ==V4L2_MBUS_CSI2_DPHY )mcam_enable_mipi (cam);else mcam_disable_mipi (cam);
drivers/media/platform/marvell-ccic/mmp-driver.c +1 -1
@@ -362,7 +362,7 @@ static int mmpcam_probe(struct platform_device *pdev) mcam->mclk_div = pdata->mclk_div; mcam->bus_type = pdata->bus_type; mcam->dphy = pdata->dphy; -if (mcam->bus_type ==V4L2_MBUS_CSI2 ) { +if (mcam->bus_type ==V4L2_MBUS_CSI2_DPHY ) { cam->mipi_clk =devm_clk_get (mcam->dev,"mipi" );if ((IS_ERR (cam->mipi_clk) && mcam->dphy[2 ] ==0 ))return PTR_ERR (cam->mipi_clk);
drivers/media/platform/omap3isp/isp.c +1 -1
@@ -2054,7 +2054,7 @@ static int isp_fwnode_parse(struct device *dev,dev_dbg (dev,"CSI-1/CCP-2 configuration\n" ); csi1 = true;break ; -case V4L2_MBUS_CSI2 : +case V4L2_MBUS_CSI2_DPHY :dev_dbg (dev,"CSI-2 configuration\n" ); csi1 = false;break ;
drivers/media/platform/pxa_camera.c +1 -1
@@ -633,7 +633,7 @@ static unsigned int pxa_mbus_config_compatible(const struct v4l2_mbus_config *cf mode = common_flags & (V4L2_MBUS_MASTER |V4L2_MBUS_SLAVE );return (!hsync || !vsync || !pclk || !data || !mode) ?0 : common_flags; -case V4L2_MBUS_CSI2 : +case V4L2_MBUS_CSI2_DPHY : mipi_lanes = common_flags &V4L2_MBUS_CSI2_LANES ; mipi_clock = common_flags & (V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK |V4L2_MBUS_CSI2_CONTINUOUS_CLOCK );
drivers/media/platform/rcar-vin/rcar-csi2.c +1 -1
@@ -714,7 +714,7 @@ static int rcsi2_parse_v4l2(struct rcar_csi2 *priv,if (vep->base.port || vep->base.id)return -ENOTCONN ; -if (vep->bus_type !=V4L2_MBUS_CSI2 ) { +if (vep->bus_type !=V4L2_MBUS_CSI2_DPHY ) {dev_err (priv->dev,"Unsupported bus: %u\n" , vep->bus_type);return -EINVAL ; }
drivers/media/platform/soc_camera/soc_mediabus.c +1 -1
@@ -503,7 +503,7 @@ unsigned int soc_mbus_config_compatible(const struct v4l2_mbus_config *cfg, mode = common_flags & (V4L2_MBUS_MASTER |V4L2_MBUS_SLAVE );return (!hsync || !vsync || !pclk || !data || !mode) ?0 : common_flags; -case V4L2_MBUS_CSI2 : +case V4L2_MBUS_CSI2_DPHY : mipi_lanes = common_flags &V4L2_MBUS_CSI2_LANES ; mipi_clock = common_flags & (V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK |V4L2_MBUS_CSI2_CONTINUOUS_CLOCK );
drivers/media/platform/stm32/stm32-dcmi.c +1 -1
@@ -1660,7 +1660,7 @@ static int dcmi_probe(struct platform_device *pdev)return -ENODEV ; } -if (ep.bus_type ==V4L2_MBUS_CSI2 ) { +if (ep.bus_type ==V4L2_MBUS_CSI2_DPHY ) {dev_err (&pdev->dev,"CSI bus not supported\n" );return -ENODEV ; }
drivers/media/platform/ti-vpe/cal.c +1 -1
@@ -1710,7 +1710,7 @@ static int of_cal_create_instance(struct cal_ctx *ctx, int inst) }v4l2_fwnode_endpoint_parse (of_fwnode_handle (remote_ep), endpoint); -if (endpoint->bus_type !=V4L2_MBUS_CSI2 ) { +if (endpoint->bus_type !=V4L2_MBUS_CSI2_DPHY ) {ctx_err (ctx,"Port:%d sub-device %s is not a CSI2 device\n" , inst, sensor_node->name); goto err_put_remote_ep;
drivers/media/v4l2-core/v4l2-fwnode.c +1 -1
@@ -115,7 +115,7 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, } bus->flags = flags; - vep->bus_type =V4L2_MBUS_CSI2 ; + vep->bus_type =V4L2_MBUS_CSI2_DPHY ;return 0 ; }
drivers/staging/media/imx/imx-media-csi.c +1 -1
@@ -124,7 +124,7 @@ static inline struct csi_priv *sd_to_dev(struct v4l2_subdev *sdev)static inline bool is_parallel_bus (struct v4l2_fwnode_endpoint *ep) { -return ep->bus_type !=V4L2_MBUS_CSI2 ; +return ep->bus_type !=V4L2_MBUS_CSI2_DPHY ; }static inline bool is_parallel_16bit_bus (struct v4l2_fwnode_endpoint *ep)
drivers/staging/media/imx/imx6-mipi-csi2.c +1 -1
@@ -563,7 +563,7 @@ static int csi2_parse_endpoint(struct device *dev,return -EINVAL ; } -if (vep->bus_type !=V4L2_MBUS_CSI2 ) { +if (vep->bus_type !=V4L2_MBUS_CSI2_DPHY ) {v4l2_err (&csi2->sd,"invalid bus type, must be MIPI CSI2\n" );return -EINVAL ; }
drivers/staging/media/imx074/imx074.c +1 -1
@@ -263,7 +263,7 @@ static int imx074_s_power(struct v4l2_subdev *sd, int on)static int imx074_g_mbus_config (struct v4l2_subdev *sd,struct v4l2_mbus_config *cfg) { - cfg->type =V4L2_MBUS_CSI2 ; + cfg->type =V4L2_MBUS_CSI2_DPHY ; cfg->flags =V4L2_MBUS_CSI2_2_LANE |V4L2_MBUS_CSI2_CHANNEL_0 |V4L2_MBUS_CSI2_CONTINUOUS_CLOCK ;
include/media/v4l2-mediabus.h +4 -2
@@ -75,14 +75,16 @@* also be used for BT.1120 * @V4L2_MBUS_CSI1: MIPI CSI-1 serial interface * @V4L2_MBUS_CCP2: CCP2 (Compact Camera Port 2) -* @V4L2_MBUS_CSI2: MIPI CSI-2 serial interface +* @V4L2_MBUS_CSI2_DPHY: MIPI CSI-2 serial interface, with D-PHY +* @V4L2_MBUS_CSI2_CPHY: MIPI CSI-2 serial interface, with C-PHY */ enum v4l2_mbus_type {V4L2_MBUS_PARALLEL ,V4L2_MBUS_BT656 ,V4L2_MBUS_CSI1 ,V4L2_MBUS_CCP2 , -V4L2_MBUS_CSI2 , +V4L2_MBUS_CSI2_DPHY , +V4L2_MBUS_CSI2_CPHY , };/**
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 7/23 v4l: fwnode: Let the caller provide V4L2 fwnode endpoint
In reply to Sakari AilusInstead of allocating the V4L2 fwnode endpoint in v4l2_fwnode_endpoint_alloc_parse, let the caller to do this. This allows setting default parameters for the endpoint which is a very common need for drivers.
--- drivers/media/i2c/ov2659.c | 14 +++++----- drivers/media/i2c/smiapp/smiapp-core.c | 26 +++++++++--------- drivers/media/i2c/tc358743.c | 26 +++++++++--------- drivers/media/v4l2-core/v4l2-fwnode.c | 49 +++++++++++++--------------------- include/media/v4l2-fwnode.h | 10 ++++--- 5 files changed, 60 insertions(+), 65 deletions(-)
drivers/media/i2c/ov2659.c +8 -6
@@ -1347,8 +1347,9 @@ static struct ov2659_platform_data * ov2659_get_pdata(struct i2c_client *client) {struct ov2659_platform_data *pdata; -struct v4l2_fwnode_endpoint *bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *endpoint; +int ret;if (!IS_ENABLED (CONFIG_OF ) || !client->dev.of_node)return client->dev.platform_data;
@@ -1357,8 +1358,9 @@ ov2659_get_pdata(struct i2c_client *client)if (!endpoint)return NULL ; - bus_cfg =v4l2_fwnode_endpoint_alloc_parse (of_fwnode_handle (endpoint)); -if (IS_ERR (bus_cfg)) { + ret =v4l2_fwnode_endpoint_alloc_parse (of_fwnode_handle (endpoint), + &bus_cfg); +if (ret) { pdata =NULL ; goto done; }
@@ -1367,17 +1369,17 @@ ov2659_get_pdata(struct i2c_client *client)if (!pdata) goto done; -if (!bus_cfg->nr_of_link_frequencies) { +if (!bus_cfg.nr_of_link_frequencies) {dev_err (&client->dev,"link-frequencies property not found or too many\n" ); pdata =NULL ; goto done; } - pdata->link_frequency = bus_cfg->link_frequencies[0 ]; + pdata->link_frequency = bus_cfg.link_frequencies[0 ]; done: -v4l2_fwnode_endpoint_free (bus_cfg); +v4l2_fwnode_endpoint_free (&bus_cfg);of_node_put (endpoint);return pdata; }
drivers/media/i2c/smiapp/smiapp-core.c +13 -13
@@ -2761,7 +2761,7 @@ static int __maybe_unused smiapp_resume(struct device *dev)static struct smiapp_hwconfig *smiapp_get_hwconfig (struct device *dev) {struct smiapp_hwconfig *hwcfg; -struct v4l2_fwnode_endpoint *bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct fwnode_handle *ep;struct fwnode_handle *fwnode =dev_fwnode (dev);u32 rotation;
@@ -2775,27 +2775,27 @@ static struct smiapp_hwconfig *smiapp_get_hwconfig(struct device *dev)if (!ep)return NULL ; - bus_cfg =v4l2_fwnode_endpoint_alloc_parse (ep); -if (IS_ERR (bus_cfg)) + rval =v4l2_fwnode_endpoint_alloc_parse (ep, &bus_cfg); +if (rval) goto out_err; hwcfg =devm_kzalloc (dev,sizeof (*hwcfg),GFP_KERNEL );if (!hwcfg) goto out_err; -switch (bus_cfg->bus_type) { +switch (bus_cfg.bus_type) {case V4L2_MBUS_CSI2_DPHY : hwcfg->csi_signalling_mode =SMIAPP_CSI_SIGNALLING_MODE_CSI2 ; - hwcfg->lanes = bus_cfg->bus.mipi_csi2.num_data_lanes; + hwcfg->lanes = bus_cfg.bus.mipi_csi2.num_data_lanes;break ;case V4L2_MBUS_CCP2 : - hwcfg->csi_signalling_mode = (bus_cfg->bus.mipi_csi1.strobe) ? + hwcfg->csi_signalling_mode = (bus_cfg.bus.mipi_csi1.strobe) ?SMIAPP_CSI_SIGNALLING_MODE_CCP2_DATA_STROBE :SMIAPP_CSI_SIGNALLING_MODE_CCP2_DATA_CLOCK ; hwcfg->lanes =1 ;break ;default : -dev_err (dev,"unsupported bus %u\n" , bus_cfg->bus_type); +dev_err (dev,"unsupported bus %u\n" , bus_cfg.bus_type); goto out_err; }
@@ -2827,28 +2827,28 @@ static struct smiapp_hwconfig *smiapp_get_hwconfig(struct device *dev)dev_dbg (dev,"nvm %d, clk %d, mode %d\n" , hwcfg->nvm_size, hwcfg->ext_clk, hwcfg->csi_signalling_mode); -if (!bus_cfg->nr_of_link_frequencies) { +if (!bus_cfg.nr_of_link_frequencies) {dev_warn (dev,"no link frequencies defined\n" ); goto out_err; } hwcfg->op_sys_clock =devm_kcalloc ( - dev, bus_cfg->nr_of_link_frequencies +1 /* guardian */ , + dev, bus_cfg.nr_of_link_frequencies +1 /* guardian */ ,sizeof (*hwcfg->op_sys_clock),GFP_KERNEL );if (!hwcfg->op_sys_clock) goto out_err; -for (i =0 ; i < bus_cfg->nr_of_link_frequencies; i++) { - hwcfg->op_sys_clock[i] = bus_cfg->link_frequencies[i]; +for (i =0 ; i < bus_cfg.nr_of_link_frequencies; i++) { + hwcfg->op_sys_clock[i] = bus_cfg.link_frequencies[i];dev_dbg (dev,"freq %d: %lld\n" , i, hwcfg->op_sys_clock[i]); } -v4l2_fwnode_endpoint_free (bus_cfg); +v4l2_fwnode_endpoint_free (&bus_cfg);fwnode_handle_put (ep);return hwcfg; out_err: -v4l2_fwnode_endpoint_free (bus_cfg); +v4l2_fwnode_endpoint_free (&bus_cfg);fwnode_handle_put (ep);return NULL ; }
drivers/media/i2c/tc358743.c +14 -12
@@ -1895,11 +1895,11 @@ static void tc358743_gpio_reset(struct tc358743_state *state)static int tc358743_probe_of (struct tc358743_state *state) {struct device *dev = &state->i2c_client->dev; -struct v4l2_fwnode_endpoint *endpoint; +struct v4l2_fwnode_endpoint endpoint = { .bus_type =0 };struct device_node *ep;struct clk *refclk;u32 bps_pr_lane; -int ret = -EINVAL ; +int ret; refclk =devm_clk_get (dev,"refclk" );if (IS_ERR (refclk)) {
@@ -1915,26 +1915,28 @@ static int tc358743_probe_of(struct tc358743_state *state)return -EINVAL ; } - endpoint =v4l2_fwnode_endpoint_alloc_parse (of_fwnode_handle (ep)); -if (IS_ERR (endpoint)) { + ret =v4l2_fwnode_endpoint_alloc_parse (of_fwnode_handle (ep), &endpoint); +if (ret) {dev_err (dev,"failed to parse endpoint\n" ); - ret =PTR_ERR (endpoint); + ret = ret; goto put_node; } -if (endpoint->bus_type !=V4L2_MBUS_CSI2_DPHY || - endpoint->bus.mipi_csi2.num_data_lanes ==0 || - endpoint->nr_of_link_frequencies ==0 ) { +if (endpoint.bus_type !=V4L2_MBUS_CSI2_DPHY || + endpoint.bus.mipi_csi2.num_data_lanes ==0 || + endpoint.nr_of_link_frequencies ==0 ) {dev_err (dev,"missing CSI-2 properties in endpoint\n" ); + ret = -EINVAL ; goto free_endpoint; } -if (endpoint->bus.mipi_csi2.num_data_lanes >4 ) { +if (endpoint.bus.mipi_csi2.num_data_lanes >4 ) {dev_err (dev,"invalid number of lanes\n" ); + ret = -EINVAL ; goto free_endpoint; } - state->bus = endpoint->bus.mipi_csi2; + state->bus = endpoint.bus.mipi_csi2; ret =clk_prepare_enable (refclk);if (ret) {
@@ -1967,7 +1969,7 @@ static int tc358743_probe_of(struct tc358743_state *state)* The CSI bps per lane must be between 62.5 Mbps and 1 Gbps. * The default is 594 Mbps for 4-lane 1080p60 or 2-lane 720p60. */ - bps_pr_lane =2 * endpoint->link_frequencies[0 ]; + bps_pr_lane =2 * endpoint.link_frequencies[0 ];if (bps_pr_lane <62500000U || bps_pr_lane >1000000000U ) {dev_err (dev,"unsupported bps per lane: %u bps\n" , bps_pr_lane); goto disable_clk;
@@ -2013,7 +2015,7 @@ static int tc358743_probe_of(struct tc358743_state *state) disable_clk:clk_disable_unprepare (refclk); free_endpoint: -v4l2_fwnode_endpoint_free (endpoint); +v4l2_fwnode_endpoint_free (&endpoint); put_node:of_node_put (ep);return ret;
drivers/media/v4l2-core/v4l2-fwnode.c +19 -30
103 lines not on this page · raw message
include/media/v4l2-fwnode.h +6 -4
@@ -161,6 +161,7 @@ void v4l2_fwnode_endpoint_free(struct v4l2_fwnode_endpoint *vep);/** * v4l2_fwnode_endpoint_alloc_parse() - parse all fwnode node properties * @fwnode: pointer to the endpoint's fwnode handle +* @vep: pointer to the V4L2 fwnode data structure * * All properties are optional. If none are found, we don't set any flags. This * means the port has a static configuration and no properties have to be
@@ -170,6 +171,8 @@ void v4l2_fwnode_endpoint_free(struct v4l2_fwnode_endpoint *vep);* set the V4L2_MBUS_CSI2_CONTINUOUS_CLOCK flag. The caller should hold a * reference to @fwnode. * +* The caller must set the bus_type field of @vep to zero. +* * v4l2_fwnode_endpoint_alloc_parse() has two important differences to * v4l2_fwnode_endpoint_parse(): *
@@ -178,11 +181,10 @@ void v4l2_fwnode_endpoint_free(struct v4l2_fwnode_endpoint *vep);* 2. The memory it has allocated to store the variable size data must be freed * using v4l2_fwnode_endpoint_free() when no longer needed. * -* Return: Pointer to v4l2_fwnode_endpoint if successful, on an error pointer -* on error. +* Return: 0 on success or a negative error code on failure. */ -struct v4l2_fwnode_endpoint *v4l2_fwnode_endpoint_alloc_parse ( -struct fwnode_handle *fwnode); +int v4l2_fwnode_endpoint_alloc_parse ( +struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep);/** * v4l2_fwnode_parse_link() - parse a link between two endpoints
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 8/23 v4l: fwnode: Detect bus type correctly
In reply to Sakari AilusIn case the device supports multiple video bus types on an endpoint, the V4L2 fwnode framework attempts to detect the type based on the available information. This wasn't working really well, and sometimes could lead to the V4L2 fwnode endpoint struct as being mishandled between the bus types.
Default to Bt.656 if no properties suggesting a bus type are found.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 31 +++++++++++++++++-------------- include/media/v4l2-mediabus.h | 2 ++ 2 files changed, 19 insertions(+), 14 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +17 -14
@@ -114,8 +114,11 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, flags |=V4L2_MBUS_CSI2_CONTINUOUS_CLOCK ; } - bus->flags = flags; - vep->bus_type =V4L2_MBUS_CSI2_DPHY ; +if (lanes_used || have_clk_lane || + (flags & ~V4L2_MBUS_CSI2_CONTINUOUS_CLOCK )) { + bus->flags = flags; + vep->bus_type =V4L2_MBUS_CSI2_DPHY ; + }return 0 ; }
@@ -145,11 +148,6 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(pr_debug ("field-even-active %s\n" , v ?"high" :"low" ); } -if (flags) - vep->bus_type =V4L2_MBUS_PARALLEL ; -else - vep->bus_type =V4L2_MBUS_BT656 ; -if (!fwnode_property_read_u32 (fwnode,"pclk-sample" , &v)) { flags |= v ?V4L2_MBUS_PCLK_SAMPLE_RISING :V4L2_MBUS_PCLK_SAMPLE_FALLING ;
@@ -192,13 +190,21 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus( } bus->flags = flags; - +if (flags & (V4L2_MBUS_HSYNC_ACTIVE_HIGH | +V4L2_MBUS_HSYNC_ACTIVE_LOW | +V4L2_MBUS_VSYNC_ACTIVE_HIGH | +V4L2_MBUS_VSYNC_ACTIVE_LOW | +V4L2_MBUS_FIELD_EVEN_HIGH | +V4L2_MBUS_FIELD_EVEN_LOW )) + vep->bus_type =V4L2_MBUS_PARALLEL ; +else + vep->bus_type =V4L2_MBUS_BT656 ; }static void v4l2_fwnode_endpoint_parse_csi1_bus (struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep, -u32 bus_type) +enum v4l2_fwnode_bus_type bus_type) {struct v4l2_fwnode_bus_mipi_csi1 *bus = &vep->bus.mipi_csi1;u32 v;
@@ -250,11 +256,8 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode, rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep);if (rval)return rval; -/* -* Parse the parallel video bus properties only if none -* of the MIPI CSI-2 specific properties were found. -*/ -if (vep->bus.mipi_csi2.flags ==0 ) + +if (vep->bus_type ==V4L2_MBUS_UNKNOWN )v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep);break ;
include/media/v4l2-mediabus.h +2 -0
@@ -70,6 +70,7 @@/** * enum v4l2_mbus_type - media bus type +* @V4L2_MBUS_UNKNOWN: unknown bus type, no V4L2 mediabus configuration * @V4L2_MBUS_PARALLEL: parallel interface with hsync and vsync * @V4L2_MBUS_BT656: parallel interface with embedded synchronisation, can * also be used for BT.1120
@@ -79,6 +80,7 @@* @V4L2_MBUS_CSI2_CPHY: MIPI CSI-2 serial interface, with C-PHY */ enum v4l2_mbus_type { +V4L2_MBUS_UNKNOWN ,V4L2_MBUS_PARALLEL ,V4L2_MBUS_BT656 ,V4L2_MBUS_CSI1 ,
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 9/23 v4l: fwnode: Make use of newly specified bus types
In reply to Sakari AilusAdd support for parsing CSI-2 D-PHY, parallel or Bt.656 bus explicitly.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 53 ++++++++++++++++++++++++++++------- 1 file changed, 43 insertions(+), 10 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +43 -10
@@ -123,8 +123,16 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,return 0 ; } +#define PARALLEL_MBUS_FLAGS (V4L2_MBUS_HSYNC_ACTIVE_HIGH | \ + V4L2_MBUS_HSYNC_ACTIVE_LOW | \ + V4L2_MBUS_VSYNC_ACTIVE_HIGH | \ + V4L2_MBUS_VSYNC_ACTIVE_LOW | \ + V4L2_MBUS_FIELD_EVEN_HIGH | \ + V4L2_MBUS_FIELD_EVEN_LOW) +static void v4l2_fwnode_endpoint_parse_parallel_bus ( -struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep) +struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep, +enum v4l2_fwnode_bus_type bus_type) {struct v4l2_fwnode_bus_parallel *bus = &vep->bus.parallel;unsigned int flags =0 ;
@@ -189,16 +197,28 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(pr_debug ("data-enable-active %s\n" , v ?"high" :"low" ); } - bus->flags = flags; -if (flags & (V4L2_MBUS_HSYNC_ACTIVE_HIGH | -V4L2_MBUS_HSYNC_ACTIVE_LOW | -V4L2_MBUS_VSYNC_ACTIVE_HIGH | -V4L2_MBUS_VSYNC_ACTIVE_LOW | -V4L2_MBUS_FIELD_EVEN_HIGH | -V4L2_MBUS_FIELD_EVEN_LOW )) +switch (bus_type) { +default : + bus->flags = flags; +if (flags & (V4L2_MBUS_HSYNC_ACTIVE_HIGH | +V4L2_MBUS_HSYNC_ACTIVE_LOW | +V4L2_MBUS_VSYNC_ACTIVE_HIGH | +V4L2_MBUS_VSYNC_ACTIVE_LOW | +V4L2_MBUS_FIELD_EVEN_HIGH | +V4L2_MBUS_FIELD_EVEN_LOW )) + vep->bus_type =V4L2_MBUS_PARALLEL ; +else + vep->bus_type =V4L2_MBUS_BT656 ; +break ; +case V4L2_FWNODE_BUS_TYPE_PARALLEL : vep->bus_type =V4L2_MBUS_PARALLEL ; -else + bus->flags = flags; +break ; +case V4L2_FWNODE_BUS_TYPE_BT656 : vep->bus_type =V4L2_MBUS_BT656 ; + bus->flags = flags & ~PARALLEL_MBUS_FLAGS ; +break ; + } } static void
@@ -258,7 +278,8 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,return rval;if (vep->bus_type ==V4L2_MBUS_UNKNOWN ) -v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep); +v4l2_fwnode_endpoint_parse_parallel_bus ( + fwnode, vep,V4L2_MBUS_UNKNOWN );break ;case V4L2_FWNODE_BUS_TYPE_CCP2 :
@@ -266,6 +287,18 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,v4l2_fwnode_endpoint_parse_csi1_bus (fwnode, vep, bus_type);break ; +case V4L2_FWNODE_BUS_TYPE_CSI2_DPHY : + vep->bus_type =V4L2_MBUS_CSI2_DPHY ; + rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep); +if (rval) +return rval; + +break ; +case V4L2_FWNODE_BUS_TYPE_PARALLEL : +case V4L2_FWNODE_BUS_TYPE_BT656 : +v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep, bus_type); + +break ;default :pr_warn ("unsupported bus type %u\n" , bus_type);return -EINVAL ;
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v3 09/23] v4l: fwnode: Make use of newly specified bus types
Hi Sakari,
Quoted 40 lines · Sakari Ailus
Add support for parsing CSI-2 D-PHY, parallel or Bt.656 bus explicitly.
Signed-off-by Sakari Ailus <[email protected]>Tested-by Steve Longerbeam <[email protected]>--- drivers/media/v4l2-core/v4l2-fwnode.c | 53 ++++++++++++++++++++++++++++------- 1 file changed, 43 insertions(+), 10 deletions(-)drivers/media/v4l2-core/v4l2-fwnode.c +9
-7@@ -123,8 +123,16 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,return 0 ; } +#define PARALLEL_MBUS_FLAGS (V4L2_MBUS_HSYNC_ACTIVE_HIGH | \ + V4L2_MBUS_HSYNC_ACTIVE_LOW | \ + V4L2_MBUS_VSYNC_ACTIVE_HIGH | \ + V4L2_MBUS_VSYNC_ACTIVE_LOW | \ + V4L2_MBUS_FIELD_EVEN_HIGH | \ + V4L2_MBUS_FIELD_EVEN_LOW) +static void v4l2_fwnode_endpoint_parse_parallel_bus ( -struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep) +struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep, +enum v4l2_fwnode_bus_type bus_type) {struct v4l2_fwnode_bus_parallel *bus = &vep->bus.parallel;unsigned int flags =0 ;@@ -189,16 +197,28 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(pr_debug ("data-enable-active %s\n" , v ?"high" :"low" ); } - bus->flags = flags; - if (flags & (V4L2_MBUS_HSYNC_ACTIVE_HIGH | - V4L2_MBUS_HSYNC_ACTIVE_LOW | - V4L2_MBUS_VSYNC_ACTIVE_HIGH | - V4L2_MBUS_VSYNC_ACTIVE_LOW | - V4L2_MBUS_FIELD_EVEN_HIGH |
drivers/media/v4l2-core/v4l2-fwnode.c static void v4l2_fwnode_endpoint_parse_parallel_bus( · line 208
Quoted 10 lines
drivers/media/v4l2-core/v4l2-fwnode.c +9
-1- V4L2_MBUS_FIELD_EVEN_LOW)) +switch (bus_type) { +default : + bus->flags = flags; +if (flags & (V4L2_MBUS_HSYNC_ACTIVE_HIGH | +V4L2_MBUS_HSYNC_ACTIVE_LOW | +V4L2_MBUS_VSYNC_ACTIVE_HIGH | +V4L2_MBUS_VSYNC_ACTIVE_LOW | +V4L2_MBUS_FIELD_EVEN_HIGH | +V4L2_MBUS_FIELD_EVEN_LOW ))
I guess you could use V4L2_MBUS_PARALLEL here.
Apart from this:
Thanks
j
Quoted 47 lines
drivers/media/v4l2-core/v4l2-fwnode.c +25
-3+ vep->bus_type =V4L2_MBUS_PARALLEL ; + else + vep->bus_type = V4L2_MBUS_BT656; +break ; +case V4L2_FWNODE_BUS_TYPE_PARALLEL : vep->bus_type =V4L2_MBUS_PARALLEL ; - else + bus->flags = flags; +break ; +case V4L2_FWNODE_BUS_TYPE_BT656 : vep->bus_type =V4L2_MBUS_BT656 ; + bus->flags = flags & ~PARALLEL_MBUS_FLAGS ; +break ; + } } static void@@ -258,7 +278,8 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,return rval;if (vep->bus_type ==V4L2_MBUS_UNKNOWN ) -v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep); +v4l2_fwnode_endpoint_parse_parallel_bus ( + fwnode, vep,V4L2_MBUS_UNKNOWN );break ;case V4L2_FWNODE_BUS_TYPE_CCP2 :@@ -266,6 +287,18 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,v4l2_fwnode_endpoint_parse_csi1_bus (fwnode, vep, bus_type);break ; +case V4L2_FWNODE_BUS_TYPE_CSI2_DPHY : + vep->bus_type =V4L2_MBUS_CSI2_DPHY ; + rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep); +if (rval) +return rval; + +break ; +case V4L2_FWNODE_BUS_TYPE_PARALLEL : +case V4L2_FWNODE_BUS_TYPE_BT656 : +v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep, bus_type); + +break ;default :pr_warn ("unsupported bus type %u\n" , bus_type);return -EINVAL ; --
Quoted 2 lines
2.11.0
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 9/23 v4l: fwnode: Make use of newly specified bus types
Add support for parsing CSI-2 D-PHY, parallel or Bt.656 bus explicitly.
---
since v3:
- Use PARALLEL_MBUS_FLAGS where appropriate --- thanks, Jacopo!
drivers/media/v4l2-core/v4l2-fwnode.c | 48 +++++++++++++++++++++++++++-------- 1 file changed, 38 insertions(+), 10 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +38 -10
@@ -123,8 +123,16 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,return 0 ; } +#define PARALLEL_MBUS_FLAGS (V4L2_MBUS_HSYNC_ACTIVE_HIGH | \ + V4L2_MBUS_HSYNC_ACTIVE_LOW | \ + V4L2_MBUS_VSYNC_ACTIVE_HIGH | \ + V4L2_MBUS_VSYNC_ACTIVE_LOW | \ + V4L2_MBUS_FIELD_EVEN_HIGH | \ + V4L2_MBUS_FIELD_EVEN_LOW) +static void v4l2_fwnode_endpoint_parse_parallel_bus ( -struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep) +struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep, +enum v4l2_fwnode_bus_type bus_type) {struct v4l2_fwnode_bus_parallel *bus = &vep->bus.parallel;unsigned int flags =0 ;
@@ -189,16 +197,23 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(pr_debug ("data-enable-active %s\n" , v ?"high" :"low" ); } - bus->flags = flags; -if (flags & (V4L2_MBUS_HSYNC_ACTIVE_HIGH | -V4L2_MBUS_HSYNC_ACTIVE_LOW | -V4L2_MBUS_VSYNC_ACTIVE_HIGH | -V4L2_MBUS_VSYNC_ACTIVE_LOW | -V4L2_MBUS_FIELD_EVEN_HIGH | -V4L2_MBUS_FIELD_EVEN_LOW )) +switch (bus_type) { +default : + bus->flags = flags; +if (flags &PARALLEL_MBUS_FLAGS ) + vep->bus_type =V4L2_MBUS_PARALLEL ; +else + vep->bus_type =V4L2_MBUS_BT656 ; +break ; +case V4L2_FWNODE_BUS_TYPE_PARALLEL : vep->bus_type =V4L2_MBUS_PARALLEL ; -else + bus->flags = flags; +break ; +case V4L2_FWNODE_BUS_TYPE_BT656 : vep->bus_type =V4L2_MBUS_BT656 ; + bus->flags = flags & ~PARALLEL_MBUS_FLAGS ; +break ; + } } static void
@@ -258,7 +273,8 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,return rval;if (vep->bus_type ==V4L2_MBUS_UNKNOWN ) -v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep); +v4l2_fwnode_endpoint_parse_parallel_bus ( + fwnode, vep,V4L2_MBUS_UNKNOWN );break ;case V4L2_FWNODE_BUS_TYPE_CCP2 :
@@ -266,6 +282,18 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,v4l2_fwnode_endpoint_parse_csi1_bus (fwnode, vep, bus_type);break ; +case V4L2_FWNODE_BUS_TYPE_CSI2_DPHY : + vep->bus_type =V4L2_MBUS_CSI2_DPHY ; + rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep); +if (rval) +return rval; + +break ; +case V4L2_FWNODE_BUS_TYPE_PARALLEL : +case V4L2_FWNODE_BUS_TYPE_BT656 : +v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep, bus_type); + +break ;default :pr_warn ("unsupported bus type %u\n" , bus_type);return -EINVAL ;
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 10/23 v4l: fwnode: Read lane inversion information despite lane numbering
In reply to Sakari AilusRead the lane inversion independently of whether the "data-lanes" property exists. This makes sense since the caller may pass the number of lanes as the default configuration while the lane inversion configuration may still be available in firmware.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 65 +++++++++++++++++++---------------- 1 file changed, 35 insertions(+), 30 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +35 -30
@@ -43,26 +43,31 @@ enum v4l2_fwnode_bus_type { };static int v4l2_fwnode_endpoint_parse_csi2_bus (struct fwnode_handle *fwnode, -struct v4l2_fwnode_endpoint *vep) +struct v4l2_fwnode_endpoint *vep, +enum v4l2_fwnode_bus_type bus_type) {struct v4l2_fwnode_bus_mipi_csi2 *bus = &vep->bus.mipi_csi2;bool have_clk_lane = false;unsigned int flags =0 , lanes_used =0 ; +u32 array[1 +V4L2_FWNODE_CSI2_MAX_DATA_LANES ]; +unsigned int num_data_lanes =0 ;unsigned int i;u32 v;int rval; +if (bus_type ==V4L2_FWNODE_BUS_TYPE_CSI2_DPHY ) + num_data_lanes =min_t (u32, bus->num_data_lanes, +V4L2_FWNODE_CSI2_MAX_DATA_LANES ); + rval =fwnode_property_read_u32_array (fwnode,"data-lanes" ,NULL ,0 );if (rval >0 ) { -u32 array[1 +V4L2_FWNODE_CSI2_MAX_DATA_LANES ]; - - bus->num_data_lanes = + num_data_lanes =min_t (int,V4L2_FWNODE_CSI2_MAX_DATA_LANES , rval);fwnode_property_read_u32_array (fwnode,"data-lanes" , array, - bus->num_data_lanes); + num_data_lanes); -for (i =0 ; i < bus->num_data_lanes; i++) { +for (i =0 ; i < num_data_lanes; i++) {if (lanes_used &BIT (array[i]))pr_warn ("duplicated lane %u in data-lanes\n" , array[i]);
@@ -71,30 +76,27 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, bus->data_lanes[i] = array[i];pr_debug ("lane %u position %u\n" , i, array[i]); } + } - rval =fwnode_property_read_u32_array (fwnode, -"lane-polarities" ,NULL , -0 ); -if (rval >0 ) { -if (rval !=1 + bus->num_data_lanes/* clock+data */ ) { -pr_warn ("invalid number of lane-polarities entries (need %u, got %u)\n" , -1 + bus->num_data_lanes, rval); -return -EINVAL ; - } + rval =fwnode_property_read_u32_array (fwnode,"lane-polarities" ,NULL , +0 ); +if (rval >0 ) { +if (rval !=1 + num_data_lanes/* clock+data */ ) { +pr_warn ("invalid number of lane-polarities entries (need %u, got %u)\n" , +1 + num_data_lanes, rval); +return -EINVAL ; + } -fwnode_property_read_u32_array (fwnode, -"lane-polarities" , array, -1 + bus->num_data_lanes); +fwnode_property_read_u32_array (fwnode,"lane-polarities" , array, +1 + num_data_lanes); -for (i =0 ; i <1 + bus->num_data_lanes; i++) { - bus->lane_polarities[i] = array[i]; -pr_debug ("lane %u polarity %sinverted" , - i, array[i] ?"" :"not " ); - } - }else { -pr_debug ("no lane polarities defined, assuming not inverted\n" ); +for (i =0 ; i <1 + num_data_lanes; i++) { + bus->lane_polarities[i] = array[i]; +pr_debug ("lane %u polarity %sinverted" , + i, array[i] ?"" :"not " ); } - + }else { +pr_debug ("no lane polarities defined, assuming not inverted\n" ); }if (!fwnode_property_read_u32 (fwnode,"clock-lanes" , &v)) {
@@ -114,10 +116,11 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, flags |=V4L2_MBUS_CSI2_CONTINUOUS_CLOCK ; } -if (lanes_used || have_clk_lane || - (flags & ~V4L2_MBUS_CSI2_CONTINUOUS_CLOCK )) { +if (bus_type ==V4L2_FWNODE_BUS_TYPE_CSI2_DPHY || lanes_used || + have_clk_lane || (flags & ~V4L2_MBUS_CSI2_CONTINUOUS_CLOCK )) { bus->flags = flags; vep->bus_type =V4L2_MBUS_CSI2_DPHY ; + bus->num_data_lanes = num_data_lanes; }return 0 ;
@@ -273,7 +276,8 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,switch (bus_type) {case V4L2_FWNODE_BUS_TYPE_GUESS : - rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep); + rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep, + bus_type);if (rval)return rval;
@@ -289,7 +293,8 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,break ;case V4L2_FWNODE_BUS_TYPE_CSI2_DPHY : vep->bus_type =V4L2_MBUS_CSI2_DPHY ; - rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep); + rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep, + bus_type);if (rval)return rval;
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 11/23 v4l: fwnode: Only assign configuration if there is no error
In reply to Sakari AilusOnly assign endpoint configuration if the endpoint is parsed successfully.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 30 ++++++++++++++++++------------ 1 file changed, 18 insertions(+), 12 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +18 -12
@@ -47,7 +47,7 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, enum v4l2_fwnode_bus_type bus_type) {struct v4l2_fwnode_bus_mipi_csi2 *bus = &vep->bus.mipi_csi2; -bool have_clk_lane = false; +bool have_clk_lane = false, have_lane_polarities = false;unsigned int flags =0 , lanes_used =0 ;u32 array[1 +V4L2_FWNODE_CSI2_MAX_DATA_LANES ];unsigned int num_data_lanes =0 ;
@@ -73,7 +73,6 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, array[i]); lanes_used |=BIT (array[i]); - bus->data_lanes[i] = array[i];pr_debug ("lane %u position %u\n" , i, array[i]); } }
@@ -87,16 +86,7 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,return -EINVAL ; } -fwnode_property_read_u32_array (fwnode,"lane-polarities" , array, -1 + num_data_lanes); - -for (i =0 ; i <1 + num_data_lanes; i++) { - bus->lane_polarities[i] = array[i]; -pr_debug ("lane %u polarity %sinverted" , - i, array[i] ?"" :"not " ); - } - }else { -pr_debug ("no lane polarities defined, assuming not inverted\n" ); + have_lane_polarities = true; }if (!fwnode_property_read_u32 (fwnode,"clock-lanes" , &v)) {
@@ -121,6 +111,22 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, bus->flags = flags; vep->bus_type =V4L2_MBUS_CSI2_DPHY ; bus->num_data_lanes = num_data_lanes; +for (i =0 ; i < num_data_lanes; i++) + bus->data_lanes[i] = array[i]; + +if (have_lane_polarities) { +fwnode_property_read_u32_array (fwnode, +"lane-polarities" , array, +1 + num_data_lanes); + +for (i =0 ; i <1 + num_data_lanes; i++) { + bus->lane_polarities[i] = array[i]; +pr_debug ("lane %u polarity %sinverted" , + i, array[i] ?"" :"not " ); + } + }else { +pr_debug ("no lane polarities defined, assuming not inverted\n" ); + } }return 0 ;
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 12/23 v4l: fwnode: Support driver-defined lane mapping defaults
In reply to Sakari AilusMake use of the default CSI-2 lane mapping from caller-passed configuration.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 20 ++++++++++++-------- 1 file changed, 12 insertions(+), 8 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +12 -8
@@ -55,10 +55,14 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,u32 v;int rval; -if (bus_type ==V4L2_FWNODE_BUS_TYPE_CSI2_DPHY ) +if (bus_type ==V4L2_FWNODE_BUS_TYPE_CSI2_DPHY ) { num_data_lanes =min_t (u32, bus->num_data_lanes,V4L2_FWNODE_CSI2_MAX_DATA_LANES ); +for (i =0 ; i < num_data_lanes; i++) + array[i] = bus->data_lanes[i]; + } + rval =fwnode_property_read_u32_array (fwnode,"data-lanes" ,NULL ,0 );if (rval >0 ) { num_data_lanes =
@@ -66,15 +70,15 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,fwnode_property_read_u32_array (fwnode,"data-lanes" , array, num_data_lanes); + } -for (i =0 ; i < num_data_lanes; i++) { -if (lanes_used &BIT (array[i])) -pr_warn ("duplicated lane %u in data-lanes\n" , - array[i]); - lanes_used |=BIT (array[i]); +for (i =0 ; i < num_data_lanes; i++) { +if (lanes_used &BIT (array[i])) +pr_warn ("duplicated lane %u in data-lanes\n" , + array[i]); + lanes_used |=BIT (array[i]); -pr_debug ("lane %u position %u\n" , i, array[i]); - } +pr_debug ("lane %u position %u\n" , i, array[i]); } rval = fwnode_property_read_u32_array(fwnode, "lane-polarities", NULL,
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 13/23 v4l: fwnode: Support default CSI-2 lane mapping for drivers
In reply to Sakari AilusMost hardware doesn't support re-mapping of the CSI-2 lanes. Especially sensor drivers have a default number of lanes. Instead of requiring the caller (the driver) to provide such a unit mapping, provide one if no mapping is configured.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 60 +++++++++++++++++++++++++++-------- 1 file changed, 46 insertions(+), 14 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +46 -14
@@ -47,20 +47,35 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, enum v4l2_fwnode_bus_type bus_type) {struct v4l2_fwnode_bus_mipi_csi2 *bus = &vep->bus.mipi_csi2; -bool have_clk_lane = false, have_lane_polarities = false; +bool have_clk_lane = false, have_data_lanes = false, + have_lane_polarities = false;unsigned int flags =0 , lanes_used =0 ;u32 array[1 +V4L2_FWNODE_CSI2_MAX_DATA_LANES ]; +u32 clock_lane =0 ;unsigned int num_data_lanes =0 ; +bool use_default_lane_mapping = false;unsigned int i;u32 v;int rval;if (bus_type ==V4L2_FWNODE_BUS_TYPE_CSI2_DPHY ) { + use_default_lane_mapping = true; + num_data_lanes =min_t (u32, bus->num_data_lanes,V4L2_FWNODE_CSI2_MAX_DATA_LANES ); -for (i =0 ; i < num_data_lanes; i++) + clock_lane = bus->clock_lane; +if (clock_lane) + use_default_lane_mapping = false; + +for (i =0 ; i < num_data_lanes; i++) { array[i] = bus->data_lanes[i]; +if (array[i]) + use_default_lane_mapping = false; + } + +if (use_default_lane_mapping) +pr_debug ("using default lane mapping\n" ); } rval =fwnode_property_read_u32_array (fwnode,"data-lanes" ,NULL ,0 );
@@ -70,15 +85,21 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,fwnode_property_read_u32_array (fwnode,"data-lanes" , array, num_data_lanes); + + have_data_lanes = true; }for (i =0 ; i < num_data_lanes; i++) { -if (lanes_used &BIT (array[i])) -pr_warn ("duplicated lane %u in data-lanes\n" , - array[i]); +if (lanes_used &BIT (array[i])) { +if (have_data_lanes || !use_default_lane_mapping) +pr_warn ("duplicated lane %u in data-lanes, using defaults\n" , + array[i]); + use_default_lane_mapping = true; + } lanes_used |=BIT (array[i]); -pr_debug ("lane %u position %u\n" , i, array[i]); +if (have_data_lanes) +pr_debug ("lane %u position %u\n" , i, array[i]); } rval = fwnode_property_read_u32_array(fwnode, "lane-polarities", NULL,
@@ -94,13 +115,16 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, }if (!fwnode_property_read_u32 (fwnode,"clock-lanes" , &v)) { -if (lanes_used &BIT (v)) -pr_warn ("duplicated lane %u in clock-lanes\n" , v); - lanes_used |=BIT (v); - - bus->clock_lane = v; - have_clk_lane = true; + clock_lane = v;pr_debug ("clock lane position %u\n" , v); + have_clk_lane = true; + } + +if (lanes_used &BIT (clock_lane)) { +if (have_clk_lane || !use_default_lane_mapping) +pr_warn ("duplicated lane %u in clock-lanes, using defaults\n" , + v); + use_default_lane_mapping = true; }if (fwnode_property_present (fwnode,"clock-noncontinuous" )) {
@@ -115,8 +139,16 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, bus->flags = flags; vep->bus_type =V4L2_MBUS_CSI2_DPHY ; bus->num_data_lanes = num_data_lanes; -for (i =0 ; i < num_data_lanes; i++) - bus->data_lanes[i] = array[i]; + +if (use_default_lane_mapping) { + bus->clock_lane =0 ; +for (i =0 ; i < num_data_lanes; i++) + bus->data_lanes[i] =1 + i; + }else { + bus->clock_lane = clock_lane; +for (i =0 ; i < num_data_lanes; i++) + bus->data_lanes[i] = array[i]; + }if (have_lane_polarities) { fwnode_property_read_u32_array(fwnode,
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 14/23 v4l: fwnode: Parse the graph endpoint as last
In reply to Sakari AilusParsing the graph endpoint is always successful; therefore parse it as last.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-)
drivers/media/v4l2-core/v4l2-fwnode.c +7 -1
@@ -308,7 +308,11 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,pr_debug ("===== begin V4L2 endpoint properties\n" ); -fwnode_graph_parse_endpoint (fwnode, &vep->base); +/* +* Zero the fwnode graph endpoint memory in case we don't end up parsing +* the endpoint. +*/ +memset (&vep->base,0 ,sizeof (vep->base));/* Zero fields from bus_type to until the end */ memset(&vep->bus_type, 0, sizeof(*vep) -
@@ -351,6 +355,8 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,return -EINVAL ; } +fwnode_graph_parse_endpoint (fwnode, &vep->base); +return 0 ; }
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 15/23 v4l: fwnode: Use default parallel flags
In reply to Sakari AilusThe caller may provide default flags for the endpoint. Change the configuration based on what is available through the fwnode property API.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
drivers/media/v4l2-core/v4l2-fwnode.c +19 -0
@@ -183,31 +183,44 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(unsigned int flags =0 ;u32 v; +if (bus_type ==V4L2_MBUS_PARALLEL || bus_type ==V4L2_MBUS_BT656 ) + flags = bus->flags; +if (!fwnode_property_read_u32 (fwnode,"hsync-active" , &v)) { + flags &= ~(V4L2_MBUS_HSYNC_ACTIVE_HIGH | +V4L2_MBUS_HSYNC_ACTIVE_LOW ); flags |= v ?V4L2_MBUS_HSYNC_ACTIVE_HIGH :V4L2_MBUS_HSYNC_ACTIVE_LOW ;pr_debug ("hsync-active %s\n" , v ?"high" :"low" ); }if (!fwnode_property_read_u32 (fwnode,"vsync-active" , &v)) { + flags &= ~(V4L2_MBUS_VSYNC_ACTIVE_HIGH | +V4L2_MBUS_VSYNC_ACTIVE_LOW ); flags |= v ?V4L2_MBUS_VSYNC_ACTIVE_HIGH :V4L2_MBUS_VSYNC_ACTIVE_LOW ;pr_debug ("vsync-active %s\n" , v ?"high" :"low" ); }if (!fwnode_property_read_u32 (fwnode,"field-even-active" , &v)) { + flags &= ~(V4L2_MBUS_FIELD_EVEN_HIGH | +V4L2_MBUS_FIELD_EVEN_LOW ); flags |= v ?V4L2_MBUS_FIELD_EVEN_HIGH :V4L2_MBUS_FIELD_EVEN_LOW ;pr_debug ("field-even-active %s\n" , v ?"high" :"low" ); }if (!fwnode_property_read_u32 (fwnode,"pclk-sample" , &v)) { + flags &= ~(V4L2_MBUS_PCLK_SAMPLE_RISING | +V4L2_MBUS_PCLK_SAMPLE_FALLING ); flags |= v ?V4L2_MBUS_PCLK_SAMPLE_RISING :V4L2_MBUS_PCLK_SAMPLE_FALLING ;pr_debug ("pclk-sample %s\n" , v ?"high" :"low" ); }if (!fwnode_property_read_u32 (fwnode,"data-active" , &v)) { + flags &= ~(V4L2_MBUS_PCLK_SAMPLE_RISING | +V4L2_MBUS_PCLK_SAMPLE_FALLING ); flags |= v ?V4L2_MBUS_DATA_ACTIVE_HIGH :V4L2_MBUS_DATA_ACTIVE_LOW ;pr_debug ("data-active %s\n" , v ?"high" :"low" );
@@ -215,8 +228,10 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(if (fwnode_property_present (fwnode,"slave-mode" )) {pr_debug ("slave mode\n" ); + flags &= ~V4L2_MBUS_MASTER ; flags |=V4L2_MBUS_SLAVE ; }else { + flags &= ~V4L2_MBUS_SLAVE ; flags |=V4L2_MBUS_MASTER ; }
@@ -231,12 +246,16 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus( }if (!fwnode_property_read_u32 (fwnode,"sync-on-green-active" , &v)) { + flags &= ~(V4L2_MBUS_VIDEO_SOG_ACTIVE_HIGH | +V4L2_MBUS_VIDEO_SOG_ACTIVE_LOW ); flags |= v ?V4L2_MBUS_VIDEO_SOG_ACTIVE_HIGH :V4L2_MBUS_VIDEO_SOG_ACTIVE_LOW ;pr_debug ("sync-on-green-active %s\n" , v ?"high" :"low" ); }if (!fwnode_property_read_u32 (fwnode,"data-enable-active" , &v)) { + flags &= ~(V4L2_MBUS_DATA_ENABLE_HIGH | +V4L2_MBUS_DATA_ENABLE_LOW ); flags |= v ?V4L2_MBUS_DATA_ENABLE_HIGH :V4L2_MBUS_DATA_ENABLE_LOW ;pr_debug ("data-enable-active %s\n" , v ?"high" :"low" );
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Re: [PATCH v3 15/23] v4l: fwnode: Use default parallel flags
Hi Sakari,
Quoted 5 lines · Sakari Ailus
The caller may provide default flags for the endpoint. Change the configuration based on what is available through the fwnode property API.
Signed-off-by Sakari Ailus <[email protected]>Tested-by Steve Longerbeam <[email protected]>
Thanks
j
Quoted 82 lines
--- drivers/media/v4l2-core/v4l2-fwnode.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)drivers/media/v4l2-core/v4l2-fwnode.c +19
-1@@ -183,31 +183,44 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(unsigned int flags =0 ;u32 v; +if (bus_type ==V4L2_MBUS_PARALLEL || bus_type ==V4L2_MBUS_BT656 ) + flags = bus->flags; +if (!fwnode_property_read_u32 (fwnode,"hsync-active" , &v)) { + flags &= ~(V4L2_MBUS_HSYNC_ACTIVE_HIGH | +V4L2_MBUS_HSYNC_ACTIVE_LOW ); flags |= v ?V4L2_MBUS_HSYNC_ACTIVE_HIGH :V4L2_MBUS_HSYNC_ACTIVE_LOW ;pr_debug ("hsync-active %s\n" , v ?"high" :"low" ); }if (!fwnode_property_read_u32 (fwnode,"vsync-active" , &v)) { + flags &= ~(V4L2_MBUS_VSYNC_ACTIVE_HIGH | +V4L2_MBUS_VSYNC_ACTIVE_LOW ); flags |= v ?V4L2_MBUS_VSYNC_ACTIVE_HIGH :V4L2_MBUS_VSYNC_ACTIVE_LOW ;pr_debug ("vsync-active %s\n" , v ?"high" :"low" ); }if (!fwnode_property_read_u32 (fwnode,"field-even-active" , &v)) { + flags &= ~(V4L2_MBUS_FIELD_EVEN_HIGH | +V4L2_MBUS_FIELD_EVEN_LOW ); flags |= v ?V4L2_MBUS_FIELD_EVEN_HIGH :V4L2_MBUS_FIELD_EVEN_LOW ;pr_debug ("field-even-active %s\n" , v ?"high" :"low" ); }if (!fwnode_property_read_u32 (fwnode,"pclk-sample" , &v)) { + flags &= ~(V4L2_MBUS_PCLK_SAMPLE_RISING | +V4L2_MBUS_PCLK_SAMPLE_FALLING ); flags |= v ?V4L2_MBUS_PCLK_SAMPLE_RISING :V4L2_MBUS_PCLK_SAMPLE_FALLING ;pr_debug ("pclk-sample %s\n" , v ?"high" :"low" ); }if (!fwnode_property_read_u32 (fwnode,"data-active" , &v)) { + flags &= ~(V4L2_MBUS_PCLK_SAMPLE_RISING | +V4L2_MBUS_PCLK_SAMPLE_FALLING ); flags |= v ?V4L2_MBUS_DATA_ACTIVE_HIGH :V4L2_MBUS_DATA_ACTIVE_LOW ;pr_debug ("data-active %s\n" , v ?"high" :"low" );@@ -215,8 +228,10 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(if (fwnode_property_present (fwnode,"slave-mode" )) {pr_debug ("slave mode\n" ); + flags &= ~V4L2_MBUS_MASTER ; flags |=V4L2_MBUS_SLAVE ; }else { + flags &= ~V4L2_MBUS_SLAVE ; flags |=V4L2_MBUS_MASTER ; }@@ -231,12 +246,16 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus( }if (!fwnode_property_read_u32 (fwnode,"sync-on-green-active" , &v)) { + flags &= ~(V4L2_MBUS_VIDEO_SOG_ACTIVE_HIGH | +V4L2_MBUS_VIDEO_SOG_ACTIVE_LOW ); flags |= v ?V4L2_MBUS_VIDEO_SOG_ACTIVE_HIGH :V4L2_MBUS_VIDEO_SOG_ACTIVE_LOW ;pr_debug ("sync-on-green-active %s\n" , v ?"high" :"low" ); }if (!fwnode_property_read_u32 (fwnode,"data-enable-active" , &v)) { + flags &= ~(V4L2_MBUS_DATA_ENABLE_HIGH | +V4L2_MBUS_DATA_ENABLE_LOW ); flags |= v ?V4L2_MBUS_DATA_ENABLE_HIGH :V4L2_MBUS_DATA_ENABLE_LOW ;pr_debug ("data-enable-active %s\n" , v ?"high" :"low" ); --
Quoted 2 lines
2.11.0
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 16/23 v4l: fwnode: Initialise the V4L2 fwnode endpoints to zero
In reply to Sakari AilusInitialise the V4L2 fwnode endpoints to zero in all drivers using v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint flags as well as the bus type. Setting bus type to zero will continue to guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).
--- drivers/media/i2c/adv7604.c | 2 +- drivers/media/i2c/mt9v032.c | 2 +- drivers/media/i2c/ov5647.c | 2 +- drivers/media/i2c/ov7670.c | 2 +- drivers/media/i2c/s5c73m3/s5c73m3-core.c | 2 +- drivers/media/i2c/s5k5baf.c | 2 +- drivers/media/i2c/tda1997x.c | 2 +- drivers/media/i2c/tvp514x.c | 2 +- drivers/media/i2c/tvp5150.c | 2 +- drivers/media/i2c/tvp7002.c | 2 +- drivers/media/platform/am437x/am437x-vpfe.c | 2 +- drivers/media/platform/atmel/atmel-isc.c | 3 ++- drivers/media/platform/atmel/atmel-isi.c | 2 +- drivers/media/platform/cadence/cdns-csi2rx.c | 2 +- drivers/media/platform/cadence/cdns-csi2tx.c | 2 +- drivers/media/platform/davinci/vpif_capture.c | 2 +- drivers/media/platform/exynos4-is/media-dev.c | 2 +- drivers/media/platform/exynos4-is/mipi-csis.c | 2 +- drivers/media/platform/pxa_camera.c | 2 +- drivers/media/platform/rcar-vin/rcar-csi2.c | 2 +- drivers/media/platform/renesas-ceu.c | 3 ++- drivers/media/platform/stm32/stm32-dcmi.c | 2 +- drivers/staging/media/imx/imx-media-csi.c | 8 ++++---- include/media/v4l2-fwnode.h | 2 ++ 24 files changed, 30 insertions(+), 26 deletions(-)
drivers/media/i2c/adv7604.c +1 -1
@@ -3093,7 +3093,7 @@ MODULE_DEVICE_TABLE(of, adv76xx_of_id);static int adv76xx_parse_dt (struct adv76xx_state *state) { -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *endpoint;struct device_node *np;unsigned int flags;
drivers/media/i2c/mt9v032.c +1 -1
@@ -989,7 +989,7 @@ static struct mt9v032_platform_data * mt9v032_get_pdata(struct i2c_client *client) {struct mt9v032_platform_data *pdata =NULL ; -struct v4l2_fwnode_endpoint endpoint; +struct v4l2_fwnode_endpoint endpoint = { .bus_type =0 };struct device_node *np;struct property *prop;
drivers/media/i2c/ov5647.c +1 -1
@@ -532,7 +532,7 @@ static const struct v4l2_subdev_internal_ops ov5647_subdev_internal_ops = {static int ov5647_parse_dt (struct device_node *np) { -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *ep;int ret;
drivers/media/i2c/ov7670.c +1 -1
@@ -1728,7 +1728,7 @@ static int ov7670_parse_dt(struct device *dev, struct ov7670_info *info) {struct fwnode_handle *fwnode =dev_fwnode (dev); -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct fwnode_handle *ep;int ret;
drivers/media/i2c/s5c73m3/s5c73m3-core.c +1 -1
@@ -1603,7 +1603,7 @@ static int s5c73m3_get_platform_data(struct s5c73m3 *state)const struct s5c73m3_platform_data *pdata = dev->platform_data;struct device_node *node = dev->of_node;struct device_node *node_ep; -struct v4l2_fwnode_endpoint ep; +struct v4l2_fwnode_endpoint ep = { .bus_type =0 };int ret;if (!node) {
drivers/media/i2c/s5k5baf.c +1 -1
@@ -1841,7 +1841,7 @@ static int s5k5baf_parse_device_node(struct s5k5baf *state, struct device *dev) {struct device_node *node = dev->of_node;struct device_node *node_ep; -struct v4l2_fwnode_endpoint ep; +struct v4l2_fwnode_endpoint ep = { .bus_type =0 };int ret;if (!node) {
drivers/media/i2c/tda1997x.c +1 -1
@@ -2265,7 +2265,7 @@ MODULE_DEVICE_TABLE(of, tda1997x_of_id);static int tda1997x_parse_dt (struct tda1997x_state *state) {struct tda1997x_platform_data *pdata = &state->pdata; -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *ep;struct device_node *np;unsigned int flags;
drivers/media/i2c/tvp514x.c +1 -1
@@ -989,7 +989,7 @@ static struct tvp514x_platform_data * tvp514x_get_pdata(struct i2c_client *client) {struct tvp514x_platform_data *pdata =NULL ; -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *endpoint;unsigned int flags;
drivers/media/i2c/tvp5150.c +1 -1
@@ -1362,7 +1362,7 @@ static int tvp5150_init(struct i2c_client *c)static int tvp5150_parse_dt (struct tvp5150 *decoder,struct device_node *np) { -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *ep;#ifdef CONFIG_MEDIA_CONTROLLER struct device_node *connectors, *child;
drivers/media/i2c/tvp7002.c +1 -1
@@ -889,7 +889,7 @@ static const struct v4l2_subdev_ops tvp7002_ops = {static struct tvp7002_config *tvp7002_get_pdata (struct i2c_client *client) { -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct tvp7002_config *pdata =NULL ;struct device_node *endpoint;unsigned int flags;
drivers/media/platform/am437x/am437x-vpfe.c +1 -1
@@ -2426,7 +2426,6 @@ static struct vpfe_config * vpfe_get_pdata(struct vpfe_device *vpfe) {struct device_node *endpoint =NULL ; -struct v4l2_fwnode_endpoint bus_cfg;struct device *dev = vpfe->pdev;struct vpfe_subdev_info *sdinfo;struct vpfe_config *pdata;
@@ -2446,6 +2445,7 @@ vpfe_get_pdata(struct vpfe_device *vpfe)return NULL ;for (i =0 ; ; i++) { +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *rem; endpoint =of_graph_get_next_endpoint (dev->of_node, endpoint);
drivers/media/platform/atmel/atmel-isc.c +2 -1
@@ -2028,7 +2028,6 @@ static int isc_parse_dt(struct device *dev, struct isc_device *isc) {struct device_node *np = dev->of_node;struct device_node *epn =NULL , *rem; -struct v4l2_fwnode_endpoint v4l2_epn;struct isc_subdev_entity *subdev_entity;unsigned int flags;int ret;
@@ -2036,6 +2035,8 @@ static int isc_parse_dt(struct device *dev, struct isc_device *isc)INIT_LIST_HEAD (&isc->subdev_entities);while (1 ) { +struct v4l2_fwnode_endpoint v4l2_epn = { .bus_type =0 }; + epn =of_graph_get_next_endpoint (np, epn);if (!epn)return 0 ;
drivers/media/platform/atmel/atmel-isi.c +1 -1
@@ -790,7 +790,7 @@ static int atmel_isi_parse_dt(struct atmel_isi *isi, struct platform_device *pdev) {struct device_node *np = pdev->dev.of_node; -struct v4l2_fwnode_endpoint ep; +struct v4l2_fwnode_endpoint ep = { .bus_type =0 };int err;/* Default settings for ISI */
drivers/media/platform/cadence/cdns-csi2rx.c +1 -1
@@ -361,7 +361,7 @@ static int csi2rx_get_resources(struct csi2rx_priv *csi2rx,static int csi2rx_parse_dt (struct csi2rx_priv *csi2rx) { -struct v4l2_fwnode_endpoint v4l2_ep; +struct v4l2_fwnode_endpoint v4l2_ep = { .bus_type =0 };struct fwnode_handle *fwh;struct device_node *ep;int ret;
drivers/media/platform/cadence/cdns-csi2tx.c +1 -1
@@ -432,7 +432,7 @@ static int csi2tx_get_resources(struct csi2tx_priv *csi2tx,static int csi2tx_check_lanes (struct csi2tx_priv *csi2tx) { -struct v4l2_fwnode_endpoint v4l2_ep; +struct v4l2_fwnode_endpoint v4l2_ep = { .bus_type =0 };struct device_node *ep;int ret;
drivers/media/platform/davinci/vpif_capture.c +1 -1
@@ -1511,7 +1511,6 @@ static struct vpif_capture_config * vpif_capture_get_pdata(struct platform_device *pdev) {struct device_node *endpoint =NULL ; -struct v4l2_fwnode_endpoint bus_cfg;struct vpif_capture_config *pdata;struct vpif_subdev_info *sdinfo;struct vpif_capture_chan_config *chan;
@@ -1541,6 +1540,7 @@ vpif_capture_get_pdata(struct platform_device *pdev)return NULL ;for (i =0 ; i <VPIF_CAPTURE_NUM_CHANNELS ; i++) { +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *rem;unsigned int flags;int err;
drivers/media/platform/exynos4-is/media-dev.c +1 -1
@@ -390,7 +390,7 @@ static int fimc_md_parse_port_node(struct fimc_md *fmd, {struct fimc_source_info *pd = &fmd->sensor[index].pdata;struct device_node *rem, *ep, *np; -struct v4l2_fwnode_endpoint endpoint; +struct v4l2_fwnode_endpoint endpoint = { .bus_type =0 };int ret;/* Assume here a port node can have only one endpoint node. */
drivers/media/platform/exynos4-is/mipi-csis.c +1 -1
@@ -718,7 +718,7 @@ static int s5pcsis_parse_dt(struct platform_device *pdev, struct csis_state *state) {struct device_node *node = pdev->dev.of_node; -struct v4l2_fwnode_endpoint endpoint; +struct v4l2_fwnode_endpoint endpoint = { .bus_type =0 };int ret; if (of_property_read_u32(node, "clock-frequency",
drivers/media/platform/pxa_camera.c +1 -1
@@ -2298,7 +2298,7 @@ static int pxa_camera_pdata_from_dt(struct device *dev, {u32 mclk_rate;struct device_node *remote, *np = dev->of_node; -struct v4l2_fwnode_endpoint ep; +struct v4l2_fwnode_endpoint ep = { .bus_type =0 };int err =of_property_read_u32 (np,"clock-frequency" , &mclk_rate);if (!err) {
drivers/media/platform/rcar-vin/rcar-csi2.c +1 -1
@@ -743,7 +743,7 @@ static int rcsi2_parse_v4l2(struct rcar_csi2 *priv,static int rcsi2_parse_dt (struct rcar_csi2 *priv) {struct device_node *ep; -struct v4l2_fwnode_endpoint v4l2_ep; +struct v4l2_fwnode_endpoint v4l2_ep = { .bus_type =0 };int ret; ep =of_graph_get_endpoint_by_regs (priv->dev->of_node,0 ,0 );
drivers/media/platform/renesas-ceu.c +2 -1
@@ -1536,7 +1536,6 @@ static int ceu_parse_platform_data(struct ceu_device *ceudev,static int ceu_parse_dt (struct ceu_device *ceudev) {struct device_node *of = ceudev->dev->of_node; -struct v4l2_fwnode_endpoint fw_ep;struct device_node *ep, *remote;struct ceu_subdev *ceu_sd;unsigned int i;
@@ -1552,6 +1551,8 @@ static int ceu_parse_dt(struct ceu_device *ceudev)return ret;for (i =0 ; i < num_ep; i++) { +struct v4l2_fwnode_endpoint fw_ep = { .bus_type =0 }; + ep =of_graph_get_endpoint_by_regs (of,0 , i);if (!ep) { dev_err(ceudev->dev,
drivers/media/platform/stm32/stm32-dcmi.c +1 -1
@@ -1621,7 +1621,7 @@ static int dcmi_probe(struct platform_device *pdev) {struct device_node *np = pdev->dev.of_node;const struct of_device_id *match =NULL ; -struct v4l2_fwnode_endpoint ep; +struct v4l2_fwnode_endpoint ep = { .bus_type =0 };struct stm32_dcmi *dcmi;struct vb2_queue *q;struct dma_chan *chan;
drivers/staging/media/imx/imx-media-csi.c +4 -4
@@ -1050,7 +1050,7 @@ static int csi_link_validate(struct v4l2_subdev *sd, struct v4l2_subdev_format *sink_fmt) {struct csi_priv *priv =v4l2_get_subdevdata (sd); -struct v4l2_fwnode_endpoint upstream_ep = {}; +struct v4l2_fwnode_endpoint upstream_ep = { .bus_type =0 };bool is_csi2;int ret;
@@ -1164,7 +1164,7 @@ static int csi_enum_mbus_code(struct v4l2_subdev *sd, struct v4l2_subdev_mbus_code_enum *code) {struct csi_priv *priv =v4l2_get_subdevdata (sd); -struct v4l2_fwnode_endpoint upstream_ep; +struct v4l2_fwnode_endpoint upstream_ep = { .bus_type =0 };const struct imx_media_pixfmt *incc;struct v4l2_mbus_framefmt *infmt;int ret =0 ;
@@ -1403,7 +1403,7 @@ static int csi_set_fmt(struct v4l2_subdev *sd, {struct csi_priv *priv =v4l2_get_subdevdata (sd);struct imx_media_video_dev *vdev = priv->vdev; -struct v4l2_fwnode_endpoint upstream_ep; +struct v4l2_fwnode_endpoint upstream_ep = { .bus_type =0 };const struct imx_media_pixfmt *cc;struct v4l2_pix_format vdev_fmt;struct v4l2_mbus_framefmt *fmt;
@@ -1542,7 +1542,7 @@ static int csi_set_selection(struct v4l2_subdev *sd, struct v4l2_subdev_selection *sel) {struct csi_priv *priv =v4l2_get_subdevdata (sd); -struct v4l2_fwnode_endpoint upstream_ep; +struct v4l2_fwnode_endpoint upstream_ep = { .bus_type =0 };struct v4l2_mbus_framefmt *infmt;struct v4l2_rect *crop, *compose;int pad, ret;
include/media/v4l2-fwnode.h +2 -0
@@ -139,6 +139,8 @@ struct v4l2_fwnode_link {* set the V4L2_MBUS_CSI2_CONTINUOUS_CLOCK flag. The caller should hold a * reference to @fwnode. * +* The caller must set the bus_type field of @vep to zero. +* * NOTE: This function does not parse properties the size of which is variable * without a low fixed limit. Please use v4l2_fwnode_endpoint_alloc_parse() in * new drivers instead.
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
jacopo mondi
maintainerRe: [PATCH v3 16/23] v4l: fwnode: Initialise the V4L2 fwnode endpoints to zero
Hi Sakari,
Quoted 5 lines · Sakari Ailus
Initialise the V4L2 fwnode endpoints to zero in all drivers using
v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint flags as well as the bus type. Setting bus type to zero will continue to guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).
I've played around with this patch, trying to use defaults in the renesas-ceu driver.
This is the resulting patch, if you want I can send it as follow-up or send it so that you can include it in your series if it's correct):
https://paste.debian.net/hidden/a7795d3e/
Thanks
j
Quoted 399 lines
Signed-off-by Sakari Ailus <[email protected]>Tested-by Steve Longerbeam <[email protected]>--- drivers/media/i2c/adv7604.c | 2 +- drivers/media/i2c/mt9v032.c | 2 +- drivers/media/i2c/ov5647.c | 2 +- drivers/media/i2c/ov7670.c | 2 +- drivers/media/i2c/s5c73m3/s5c73m3-core.c | 2 +- drivers/media/i2c/s5k5baf.c | 2 +- drivers/media/i2c/tda1997x.c | 2 +- drivers/media/i2c/tvp514x.c | 2 +- drivers/media/i2c/tvp5150.c | 2 +- drivers/media/i2c/tvp7002.c | 2 +- drivers/media/platform/am437x/am437x-vpfe.c | 2 +- drivers/media/platform/atmel/atmel-isc.c | 3 ++- drivers/media/platform/atmel/atmel-isi.c | 2 +- drivers/media/platform/cadence/cdns-csi2rx.c | 2 +- drivers/media/platform/cadence/cdns-csi2tx.c | 2 +- drivers/media/platform/davinci/vpif_capture.c | 2 +- drivers/media/platform/exynos4-is/media-dev.c | 2 +- drivers/media/platform/exynos4-is/mipi-csis.c | 2 +- drivers/media/platform/pxa_camera.c | 2 +- drivers/media/platform/rcar-vin/rcar-csi2.c | 2 +- drivers/media/platform/renesas-ceu.c | 3 ++- drivers/media/platform/stm32/stm32-dcmi.c | 2 +- drivers/staging/media/imx/imx-media-csi.c | 8 ++++---- include/media/v4l2-fwnode.h | 2 ++ 24 files changed, 30 insertions(+), 26 deletions(-)drivers/media/i2c/adv7604.c +1
-1@@ -3093,7 +3093,7 @@ MODULE_DEVICE_TABLE(of, adv76xx_of_id);static int adv76xx_parse_dt (struct adv76xx_state *state) { -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *endpoint;struct device_node *np;unsigned int flags;drivers/media/i2c/mt9v032.c +1
-1@@ -989,7 +989,7 @@ static struct mt9v032_platform_data * mt9v032_get_pdata(struct i2c_client *client) {struct mt9v032_platform_data *pdata =NULL ; -struct v4l2_fwnode_endpoint endpoint; +struct v4l2_fwnode_endpoint endpoint = { .bus_type =0 };struct device_node *np;struct property *prop;drivers/media/i2c/ov5647.c +1
-1@@ -532,7 +532,7 @@ static const struct v4l2_subdev_internal_ops ov5647_subdev_internal_ops = {static int ov5647_parse_dt (struct device_node *np) { -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *ep;int ret;drivers/media/i2c/ov7670.c +1
-1@@ -1728,7 +1728,7 @@ static int ov7670_parse_dt(struct device *dev, struct ov7670_info *info) {struct fwnode_handle *fwnode =dev_fwnode (dev); -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct fwnode_handle *ep;int ret;drivers/media/i2c/s5c73m3/s5c73m3-core.c +1
-1@@ -1603,7 +1603,7 @@ static int s5c73m3_get_platform_data(struct s5c73m3 *state)const struct s5c73m3_platform_data *pdata = dev->platform_data;struct device_node *node = dev->of_node;struct device_node *node_ep; -struct v4l2_fwnode_endpoint ep; +struct v4l2_fwnode_endpoint ep = { .bus_type =0 };int ret;if (!node) {drivers/media/i2c/s5k5baf.c +1
-1@@ -1841,7 +1841,7 @@ static int s5k5baf_parse_device_node(struct s5k5baf *state, struct device *dev) {struct device_node *node = dev->of_node;struct device_node *node_ep; -struct v4l2_fwnode_endpoint ep; +struct v4l2_fwnode_endpoint ep = { .bus_type =0 };int ret;if (!node) {drivers/media/i2c/tda1997x.c +1
-1@@ -2265,7 +2265,7 @@ MODULE_DEVICE_TABLE(of, tda1997x_of_id);static int tda1997x_parse_dt (struct tda1997x_state *state) {struct tda1997x_platform_data *pdata = &state->pdata; -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *ep;struct device_node *np;unsigned int flags;drivers/media/i2c/tvp514x.c +1
-1@@ -989,7 +989,7 @@ static struct tvp514x_platform_data * tvp514x_get_pdata(struct i2c_client *client) {struct tvp514x_platform_data *pdata =NULL ; -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *endpoint;unsigned int flags;drivers/media/i2c/tvp5150.c +1
-1@@ -1362,7 +1362,7 @@ static int tvp5150_init(struct i2c_client *c)static int tvp5150_parse_dt (struct tvp5150 *decoder,struct device_node *np) { -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *ep;#ifdef CONFIG_MEDIA_CONTROLLER struct device_node *connectors, *child;drivers/media/i2c/tvp7002.c +1
-1@@ -889,7 +889,7 @@ static const struct v4l2_subdev_ops tvp7002_ops = {static struct tvp7002_config *tvp7002_get_pdata (struct i2c_client *client) { -struct v4l2_fwnode_endpoint bus_cfg; +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct tvp7002_config *pdata =NULL ;struct device_node *endpoint;unsigned int flags;drivers/media/platform/am437x/am437x-vpfe.c +1
-1@@ -2426,7 +2426,6 @@ static struct vpfe_config * vpfe_get_pdata(struct vpfe_device *vpfe) {struct device_node *endpoint =NULL ; -struct v4l2_fwnode_endpoint bus_cfg;struct device *dev = vpfe->pdev;struct vpfe_subdev_info *sdinfo;struct vpfe_config *pdata;@@ -2446,6 +2445,7 @@ vpfe_get_pdata(struct vpfe_device *vpfe)return NULL ;for (i =0 ; ; i++) { +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *rem; endpoint =of_graph_get_next_endpoint (dev->of_node, endpoint);drivers/media/platform/atmel/atmel-isc.c +2
-1@@ -2028,7 +2028,6 @@ static int isc_parse_dt(struct device *dev, struct isc_device *isc) {struct device_node *np = dev->of_node;struct device_node *epn =NULL , *rem; -struct v4l2_fwnode_endpoint v4l2_epn;struct isc_subdev_entity *subdev_entity;unsigned int flags;int ret;@@ -2036,6 +2035,8 @@ static int isc_parse_dt(struct device *dev, struct isc_device *isc)INIT_LIST_HEAD (&isc->subdev_entities);while (1 ) { +struct v4l2_fwnode_endpoint v4l2_epn = { .bus_type =0 }; + epn =of_graph_get_next_endpoint (np, epn);if (!epn)return 0 ;drivers/media/platform/atmel/atmel-isi.c +1
-1@@ -790,7 +790,7 @@ static int atmel_isi_parse_dt(struct atmel_isi *isi, struct platform_device *pdev) {struct device_node *np = pdev->dev.of_node; -struct v4l2_fwnode_endpoint ep; +struct v4l2_fwnode_endpoint ep = { .bus_type =0 };int err;/* Default settings for ISI */ drivers/media/platform/cadence/cdns-csi2rx.c +1
-1@@ -361,7 +361,7 @@ static int csi2rx_get_resources(struct csi2rx_priv *csi2rx,static int csi2rx_parse_dt (struct csi2rx_priv *csi2rx) { -struct v4l2_fwnode_endpoint v4l2_ep; +struct v4l2_fwnode_endpoint v4l2_ep = { .bus_type =0 };struct fwnode_handle *fwh;struct device_node *ep;int ret;drivers/media/platform/cadence/cdns-csi2tx.c +1
-1@@ -432,7 +432,7 @@ static int csi2tx_get_resources(struct csi2tx_priv *csi2tx,static int csi2tx_check_lanes (struct csi2tx_priv *csi2tx) { -struct v4l2_fwnode_endpoint v4l2_ep; +struct v4l2_fwnode_endpoint v4l2_ep = { .bus_type =0 };struct device_node *ep;int ret;drivers/media/platform/davinci/vpif_capture.c +1
-1@@ -1511,7 +1511,6 @@ static struct vpif_capture_config * vpif_capture_get_pdata(struct platform_device *pdev) {struct device_node *endpoint =NULL ; -struct v4l2_fwnode_endpoint bus_cfg;struct vpif_capture_config *pdata;struct vpif_subdev_info *sdinfo;struct vpif_capture_chan_config *chan;@@ -1541,6 +1540,7 @@ vpif_capture_get_pdata(struct platform_device *pdev)return NULL ;for (i =0 ; i <VPIF_CAPTURE_NUM_CHANNELS ; i++) { +struct v4l2_fwnode_endpoint bus_cfg = { .bus_type =0 };struct device_node *rem;unsigned int flags;int err;drivers/media/platform/exynos4-is/media-dev.c +1
-1@@ -390,7 +390,7 @@ static int fimc_md_parse_port_node(struct fimc_md *fmd, {struct fimc_source_info *pd = &fmd->sensor[index].pdata;struct device_node *rem, *ep, *np; -struct v4l2_fwnode_endpoint endpoint; +struct v4l2_fwnode_endpoint endpoint = { .bus_type =0 };int ret;/* Assume here a port node can have only one endpoint node. */ drivers/media/platform/exynos4-is/mipi-csis.c +1
-1@@ -718,7 +718,7 @@ static int s5pcsis_parse_dt(struct platform_device *pdev, struct csis_state *state) {struct device_node *node = pdev->dev.of_node; -struct v4l2_fwnode_endpoint endpoint; +struct v4l2_fwnode_endpoint endpoint = { .bus_type =0 };int ret; if (of_property_read_u32(node, "clock-frequency",drivers/media/platform/pxa_camera.c +1
-1@@ -2298,7 +2298,7 @@ static int pxa_camera_pdata_from_dt(struct device *dev, {u32 mclk_rate;struct device_node *remote, *np = dev->of_node; -struct v4l2_fwnode_endpoint ep; +struct v4l2_fwnode_endpoint ep = { .bus_type =0 };int err =of_property_read_u32 (np,"clock-frequency" , &mclk_rate);if (!err) {drivers/media/platform/rcar-vin/rcar-csi2.c +1
-1@@ -743,7 +743,7 @@ static int rcsi2_parse_v4l2(struct rcar_csi2 *priv,static int rcsi2_parse_dt (struct rcar_csi2 *priv) {struct device_node *ep; -struct v4l2_fwnode_endpoint v4l2_ep; +struct v4l2_fwnode_endpoint v4l2_ep = { .bus_type =0 };int ret; ep =of_graph_get_endpoint_by_regs (priv->dev->of_node,0 ,0 );drivers/media/platform/renesas-ceu.c +2
-1@@ -1536,7 +1536,6 @@ static int ceu_parse_platform_data(struct ceu_device *ceudev,static int ceu_parse_dt (struct ceu_device *ceudev) {struct device_node *of = ceudev->dev->of_node; -struct v4l2_fwnode_endpoint fw_ep;struct device_node *ep, *remote;struct ceu_subdev *ceu_sd;unsigned int i;@@ -1552,6 +1551,8 @@ static int ceu_parse_dt(struct ceu_device *ceudev)return ret;for (i =0 ; i < num_ep; i++) { +struct v4l2_fwnode_endpoint fw_ep = { .bus_type =0 }; + ep =of_graph_get_endpoint_by_regs (of,0 , i);if (!ep) { dev_err(ceudev->dev,drivers/media/platform/stm32/stm32-dcmi.c +1
-1@@ -1621,7 +1621,7 @@ static int dcmi_probe(struct platform_device *pdev) {struct device_node *np = pdev->dev.of_node;const struct of_device_id *match =NULL ; -struct v4l2_fwnode_endpoint ep; +struct v4l2_fwnode_endpoint ep = { .bus_type =0 };struct stm32_dcmi *dcmi;struct vb2_queue *q;struct dma_chan *chan;drivers/staging/media/imx/imx-media-csi.c +4
-4@@ -1050,7 +1050,7 @@ static int csi_link_validate(struct v4l2_subdev *sd, struct v4l2_subdev_format *sink_fmt) {struct csi_priv *priv =v4l2_get_subdevdata (sd); -struct v4l2_fwnode_endpoint upstream_ep = {}; +struct v4l2_fwnode_endpoint upstream_ep = { .bus_type =0 };bool is_csi2;int ret;@@ -1164,7 +1164,7 @@ static int csi_enum_mbus_code(struct v4l2_subdev *sd, struct v4l2_subdev_mbus_code_enum *code) {struct csi_priv *priv =v4l2_get_subdevdata (sd); -struct v4l2_fwnode_endpoint upstream_ep; +struct v4l2_fwnode_endpoint upstream_ep = { .bus_type =0 };const struct imx_media_pixfmt *incc;struct v4l2_mbus_framefmt *infmt;int ret =0 ;@@ -1403,7 +1403,7 @@ static int csi_set_fmt(struct v4l2_subdev *sd, {struct csi_priv *priv =v4l2_get_subdevdata (sd);struct imx_media_video_dev *vdev = priv->vdev; -struct v4l2_fwnode_endpoint upstream_ep; +struct v4l2_fwnode_endpoint upstream_ep = { .bus_type =0 };const struct imx_media_pixfmt *cc;struct v4l2_pix_format vdev_fmt;struct v4l2_mbus_framefmt *fmt;@@ -1542,7 +1542,7 @@ static int csi_set_selection(struct v4l2_subdev *sd, struct v4l2_subdev_selection *sel) {struct csi_priv *priv =v4l2_get_subdevdata (sd); -struct v4l2_fwnode_endpoint upstream_ep; +struct v4l2_fwnode_endpoint upstream_ep = { .bus_type =0 };struct v4l2_mbus_framefmt *infmt;struct v4l2_rect *crop, *compose;int pad, ret;include/media/v4l2-fwnode.h +2
-1@@ -139,6 +139,8 @@ struct v4l2_fwnode_link {* set the V4L2_MBUS_CSI2_CONTINUOUS_CLOCK flag. The caller should hold a * reference to @fwnode. * +* The caller must set the bus_type field of @vep to zero. +* * NOTE: This function does not parse properties the size of which is variable * without a low fixed limit. Please use v4l2_fwnode_endpoint_alloc_parse() in * new drivers instead. --
Quoted 2 lines
2.11.0
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerRe: [PATCH v3 16/23] v4l: fwnode: Initialise the V4L2 fwnode endpoints to zero
Hi Jacopo,
Quoted 9 lines · jacopo mondi
Hi Sakari,
Quoted 5 lines · Sakari Ailus
Initialise the V4L2 fwnode endpoints to zero in all drivers using
v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint flags as well as the bus type. Setting bus type to zero will continue to guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).
Quoted 6 lines
I've played around with this patch, trying to use defaults in the renesas-ceu driver.
This is the resulting patch, if you want I can send it as follow-up or send it so that you can include it in your series if it's correct):
https://paste.debian.net/hidden/a7795d3e/
Looks nice; could you send it out to the list for review?
The bus width default isn't specified in DT bindings; could you write a patch that defines it?
Thanks.
Signature · 6 lines
Sakari Ailus [email protected] _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerRe: [PATCH v3 16/23] v4l: fwnode: Initialise the V4L2 fwnode endpoints to zero
Quoted 15 lines · Sakari Ailus
Hi Jacopo,
Quoted 12 lines · jacopo mondi
Hi Sakari,
Quoted 5 lines · Sakari Ailus
Initialise the V4L2 fwnode endpoints to zero in all drivers using
v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint flags as well as the bus type. Setting bus type to zero will continue to guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).I've played around with this patch, trying to use defaults in the renesas-ceu driver.
Quoted 8 lines
Quoted 3 lines
This is the resulting patch, if you want I can send it as follow-up or send it so that you can include it in your series if it's correct):
https://paste.debian.net/hidden/a7795d3e/Looks nice; could you send it out to the list for review?
The bus width default isn't specified in DT bindings; could you write a patch that defines it?
Same for "pclk-sample". DT bindings do not document that; it should go to the same patch.
Signature · 6 lines
Sakari Ailus [email protected] _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
jacopo mondi
maintainerRe: [PATCH v3 16/23] v4l: fwnode: Initialise the V4L2 fwnode endpoints to zero
Hi Sakari,
Quoted 20 lines · Sakari Ailus
Quoted 19 lines · Sakari Ailus
Hi Jacopo,
Quoted 15 lines · jacopo mondi
Hi Sakari,
Quoted 5 lines · Sakari Ailus
Initialise the V4L2 fwnode endpoints to zero in all drivers using
v4l2_fwnode_endpoint_parse(). This prepares for setting default endpoint flags as well as the bus type. Setting bus type to zero will continue to guess the bus among the guessable set (parallel, Bt.656 and CSI-2 D-PHY).I've played around with this patch, trying to use defaults in the renesas-ceu driver.
This is the resulting patch, if you want I can send it as follow-up or send it so that you can include it in your series if it's correct):
https://paste.debian.net/hidden/a7795d3e/
Quoted 7 lines
Quoted 4 lines
Looks nice; could you send it out to the list for review?
The bus width default isn't specified in DT bindings; could you write a patch that defines it?
Same for "pclk-sample". DT bindings do not document that; it should go to the same patch.
Actually it is 'wrong' to specify it in the default configuration in first place, as the interface does not support configuring the pixel clock edge on which to sample data.
Same for data-shift, as the interface supports 8 or 16 bits only capture modes.
I'll document bus_width restricting the accepted values to 8 and 16 and field-even-active as even if they're not actually implemented in the driver, they are configurable for the interface.
Thanks
j
Quoted 4 lines
--
Sakari Ailus
[email protected]
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 17/23 v4l: fwnode: Only zero the struct if bus type is set to V4L2_MBUS_UNKNOWN
In reply to Sakari AilusIn order to prepare for allowing drivers to set the defaults for a given bus, make zeroing the struct conditional based on detecting the bus. All callers now set the bus type to zero which allows only zeroing the remaining bus union.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +6 -4
@@ -325,6 +325,12 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,u32 bus_type =0 ;int rval; +if (vep->bus_type ==V4L2_MBUS_UNKNOWN ) { +/* Zero fields from bus union to until the end */ +memset (&vep->bus,0 , + sizeof(*vep) - offsetof(typeof(*vep), bus)); + } +pr_debug ("===== begin V4L2 endpoint properties\n" );/*
@@ -333,10 +339,6 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,*/ memset (&vep->base,0 ,sizeof (vep->base)); -/* Zero fields from bus_type to until the end */ -memset (&vep->bus_type,0 ,sizeof (*vep) - - offsetof(typeof(*vep), bus_type)); -fwnode_property_read_u32 (fwnode,"bus-type" , &bus_type);switch (bus_type) {
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 18/23 v4l: fwnode: Use media bus type for bus parser selection
In reply to Sakari AilusUse the media bus types instead of the fwnode bus types internally. This is the interface to the drivers as well, making the use of the fwnode bus types more localised to the V4L2 fwnode framework.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 100 +++++++++++++++++++++++++++------- 1 file changed, 80 insertions(+), 20 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +80 -20
@@ -42,9 +42,66 @@ enum v4l2_fwnode_bus_type { NR_OF_V4L2_FWNODE_BUS_TYPE, }; +static const struct v4l2_fwnode_bus_conv { +enum v4l2_fwnode_bus_type fwnode_bus_type; +enum v4l2_mbus_type mbus_type; +const char *name; +} busses[] = { + { +V4L2_FWNODE_BUS_TYPE_GUESS , +V4L2_MBUS_UNKNOWN , +"not specified" , + }, { +V4L2_FWNODE_BUS_TYPE_CSI2_CPHY , +V4L2_MBUS_CSI2_CPHY , +"MIPI CSI-2 C-PHY" , + }, { +V4L2_FWNODE_BUS_TYPE_CSI1 , +V4L2_MBUS_CSI1 , +"MIPI CSI-1" , + }, { +V4L2_FWNODE_BUS_TYPE_CCP2 , +V4L2_MBUS_CCP2 , +"compact camera port 2" , + }, { +V4L2_FWNODE_BUS_TYPE_CSI2_DPHY , +V4L2_MBUS_CSI2_DPHY , +"MIPI CSI-2 D-PHY" , + }, { +V4L2_FWNODE_BUS_TYPE_PARALLEL , +V4L2_MBUS_PARALLEL , +"parallel" , + }, { +V4L2_FWNODE_BUS_TYPE_BT656 , +V4L2_MBUS_BT656 , +"Bt.656" , + } +}; + +static const struct v4l2_fwnode_bus_conv * +get_v4l2_fwnode_bus_conv_by_fwnode_bus (enum v4l2_fwnode_bus_type type) +{ +unsigned int i; + +for (i =0 ; i <ARRAY_SIZE (busses); i++) +if (busses[i].fwnode_bus_type == type) +return &busses[i]; + +return NULL ; +} + +static enum v4l2_mbus_type +v4l2_fwnode_bus_type_to_mbus (enum v4l2_fwnode_bus_type type) +{ +const struct v4l2_fwnode_bus_conv *conv = +get_v4l2_fwnode_bus_conv_by_fwnode_bus (type); + +return conv ? conv->mbus_type :V4L2_MBUS_UNKNOWN ; +} +static int v4l2_fwnode_endpoint_parse_csi2_bus (struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep, -enum v4l2_fwnode_bus_type bus_type) +enum v4l2_mbus_type bus_type) {struct v4l2_fwnode_bus_mipi_csi2 *bus = &vep->bus.mipi_csi2; bool have_clk_lane = false, have_data_lanes = false,
@@ -58,7 +115,7 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,u32 v;int rval; -if (bus_type ==V4L2_FWNODE_BUS_TYPE_CSI2_DPHY ) { +if (bus_type ==V4L2_MBUS_CSI2_DPHY ) { use_default_lane_mapping = true; num_data_lanes = min_t(u32, bus->num_data_lanes,
@@ -134,7 +191,7 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, flags |=V4L2_MBUS_CSI2_CONTINUOUS_CLOCK ; } -if (bus_type ==V4L2_FWNODE_BUS_TYPE_CSI2_DPHY || lanes_used || +if (bus_type ==V4L2_MBUS_CSI2_DPHY || lanes_used || have_clk_lane || (flags & ~V4L2_MBUS_CSI2_CONTINUOUS_CLOCK )) { bus->flags = flags; vep->bus_type =V4L2_MBUS_CSI2_DPHY ;
@@ -177,7 +234,7 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,static void v4l2_fwnode_endpoint_parse_parallel_bus (struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep, -enum v4l2_fwnode_bus_type bus_type) +enum v4l2_mbus_type bus_type) {struct v4l2_fwnode_bus_parallel *bus = &vep->bus.parallel;unsigned int flags =0 ;
@@ -274,11 +331,11 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(else vep->bus_type =V4L2_MBUS_BT656 ;break ; -case V4L2_FWNODE_BUS_TYPE_PARALLEL : +case V4L2_MBUS_PARALLEL : vep->bus_type =V4L2_MBUS_PARALLEL ; bus->flags = flags;break ; -case V4L2_FWNODE_BUS_TYPE_BT656 : +case V4L2_MBUS_BT656 : vep->bus_type =V4L2_MBUS_BT656 ; bus->flags = flags & ~PARALLEL_MBUS_FLAGS ;break ;
@@ -288,7 +345,7 @@ static void v4l2_fwnode_endpoint_parse_parallel_bus(static void v4l2_fwnode_endpoint_parse_csi1_bus (struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep, -enum v4l2_fwnode_bus_type bus_type) +enum v4l2_mbus_type bus_type) {struct v4l2_fwnode_bus_mipi_csi1 *bus = &vep->bus.mipi_csi1;u32 v;
@@ -313,7 +370,7 @@ v4l2_fwnode_endpoint_parse_csi1_bus(struct fwnode_handle *fwnode,pr_debug ("clock-lanes %u\n" , v); } -if (bus_type ==V4L2_FWNODE_BUS_TYPE_CCP2 ) +if (bus_type ==V4L2_MBUS_CCP2 ) vep->bus_type =V4L2_MBUS_CCP2 ;else vep->bus_type =V4L2_MBUS_CSI1 ;
@@ -323,6 +380,7 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode, struct v4l2_fwnode_endpoint *vep) {u32 bus_type =0 ; +enum v4l2_mbus_type mbus_type;int rval;if (vep->bus_type ==V4L2_MBUS_UNKNOWN ) {
@@ -341,10 +399,12 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,fwnode_property_read_u32 (fwnode,"bus-type" , &bus_type); -switch (bus_type) { -case V4L2_FWNODE_BUS_TYPE_GUESS : + mbus_type =v4l2_fwnode_bus_type_to_mbus (bus_type); + +switch (mbus_type) { +case V4L2_MBUS_UNKNOWN : rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep, - bus_type); + mbus_type);if (rval)return rval;
@@ -353,26 +413,26 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode, fwnode, vep, V4L2_MBUS_UNKNOWN);break ; -case V4L2_FWNODE_BUS_TYPE_CCP2 : -case V4L2_FWNODE_BUS_TYPE_CSI1 : -v4l2_fwnode_endpoint_parse_csi1_bus (fwnode, vep, bus_type); +case V4L2_MBUS_CCP2 : +case V4L2_MBUS_CSI1 : +v4l2_fwnode_endpoint_parse_csi1_bus (fwnode, vep, mbus_type);break ; -case V4L2_FWNODE_BUS_TYPE_CSI2_DPHY : +case V4L2_MBUS_CSI2_DPHY : vep->bus_type =V4L2_MBUS_CSI2_DPHY ; rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep, - bus_type); + mbus_type);if (rval)return rval;break ; -case V4L2_FWNODE_BUS_TYPE_PARALLEL : -case V4L2_FWNODE_BUS_TYPE_BT656 : -v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep, bus_type); +case V4L2_MBUS_PARALLEL : +case V4L2_MBUS_BT656 : +v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep, mbus_type);break ;default : -pr_warn ("unsupported bus type %u\n" , bus_type); +pr_warn ("unsupported bus type %u\n" , mbus_type);return -EINVAL ; }
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 19/23 v4l: fwnode: Print bus type
In reply to Sakari AilusPrint bus type either as set by the driver or as parsed from the bus-type property, as well as the guessed V4L2 media bus type.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 38 +++++++++++++++++++++++++++++++++++ 1 file changed, 38 insertions(+)
drivers/media/v4l2-core/v4l2-fwnode.c +38 -0
@@ -99,6 +99,36 @@ v4l2_fwnode_bus_type_to_mbus(enum v4l2_fwnode_bus_type type)return conv ? conv->mbus_type :V4L2_MBUS_UNKNOWN ; } +static const char * +v4l2_fwnode_bus_type_to_string (enum v4l2_fwnode_bus_type type) +{ +const struct v4l2_fwnode_bus_conv *conv = +get_v4l2_fwnode_bus_conv_by_fwnode_bus (type); + +return conv ? conv->name :"not found" ; +} + +static const struct v4l2_fwnode_bus_conv * +get_v4l2_fwnode_bus_conv_by_mbus (enum v4l2_mbus_type type) +{ +unsigned int i; + +for (i =0 ; i <ARRAY_SIZE (busses); i++) +if (busses[i].mbus_type == type) +return &busses[i]; + +return NULL ; +} + +static const char * +v4l2_fwnode_mbus_type_to_string (enum v4l2_mbus_type type) +{ +const struct v4l2_fwnode_bus_conv *conv = +get_v4l2_fwnode_bus_conv_by_mbus (type); + +return conv ? conv->name :"not found" ; +} +static int v4l2_fwnode_endpoint_parse_csi2_bus (struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep,enum v4l2_mbus_type bus_type)
@@ -398,6 +428,10 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,memset (&vep->base,0 ,sizeof (vep->base));fwnode_property_read_u32 (fwnode,"bus-type" , &bus_type); +pr_debug ("fwnode video bus type %s (%u), mbus type %s (%u)\n" , +v4l2_fwnode_bus_type_to_string (bus_type), bus_type, +v4l2_fwnode_mbus_type_to_string (vep->bus_type), + vep->bus_type); mbus_type =v4l2_fwnode_bus_type_to_mbus (bus_type);
@@ -412,6 +446,10 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,v4l2_fwnode_endpoint_parse_parallel_bus ( fwnode, vep,V4L2_MBUS_UNKNOWN ); +pr_debug ("assuming media bus type %s (%u)\n" , +v4l2_fwnode_mbus_type_to_string (vep->bus_type), + vep->bus_type); +break ;case V4L2_MBUS_CCP2 :case V4L2_MBUS_CSI1 :
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 20/23 v4l: fwnode: Use V4L2 fwnode endpoint media bus type if set
In reply to Sakari AilusUse the given media bus type set by the caller. If none is given (i.e. the mbus type is V4L2_MBUS_UNKNOWN, or 0), fall back to the old behaviour. This is to obtain the information from the DT or try to guess the bus type.
-ENXIO is returned if the caller sets the bus type but that does not match with what's in DT. Also return -ENXIO if bus type detection failed to separate this from the rest of the errors.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 27 +++++++++++++++++++-------- 1 file changed, 19 insertions(+), 8 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +19 -8
@@ -409,7 +409,7 @@ v4l2_fwnode_endpoint_parse_csi1_bus(struct fwnode_handle *fwnode,static int __v4l2_fwnode_endpoint_parse (struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep) { -u32 bus_type =0 ; +u32 bus_type =V4L2_FWNODE_BUS_TYPE_GUESS ;enum v4l2_mbus_type mbus_type;int rval;
@@ -432,13 +432,24 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,v4l2_fwnode_bus_type_to_string (bus_type), bus_type,v4l2_fwnode_mbus_type_to_string (vep->bus_type), vep->bus_type); - mbus_type =v4l2_fwnode_bus_type_to_mbus (bus_type); -switch (mbus_type) { +if (vep->bus_type !=V4L2_MBUS_UNKNOWN ) { +if (mbus_type !=V4L2_MBUS_UNKNOWN && + vep->bus_type != mbus_type) { +pr_debug ("expecting bus type %s\n" , +v4l2_fwnode_mbus_type_to_string ( + vep->bus_type)); +return -ENXIO ; + } + }else { + vep->bus_type = mbus_type; + } + +switch (vep->bus_type) {case V4L2_MBUS_UNKNOWN : rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep, - mbus_type); +V4L2_MBUS_UNKNOWN );if (rval)return rval;
@@ -453,20 +464,20 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,break ;case V4L2_MBUS_CCP2 :case V4L2_MBUS_CSI1 : -v4l2_fwnode_endpoint_parse_csi1_bus (fwnode, vep, mbus_type); +v4l2_fwnode_endpoint_parse_csi1_bus (fwnode, vep, vep->bus_type);break ;case V4L2_MBUS_CSI2_DPHY : - vep->bus_type =V4L2_MBUS_CSI2_DPHY ; rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep, - mbus_type); + vep->bus_type);if (rval)return rval;break ;case V4L2_MBUS_PARALLEL :case V4L2_MBUS_BT656 : -v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep, mbus_type); +v4l2_fwnode_endpoint_parse_parallel_bus (fwnode, vep, + vep->bus_type);break ;default :
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 21/23 v4l: fwnode: Support parsing of CSI-2 C-PHY endpoints
In reply to Sakari AilusThe V4L2 fwnode framework only parsed CSI-2 D-PHY endpoints while C-PHY support wasn't there. Also parse endpoints for media bus type V4L2_MBUS_CSI2_CPHY.
--- drivers/media/v4l2-core/v4l2-fwnode.c | 10 +++++++--- 1 file changed, 7 insertions(+), 3 deletions(-)
drivers/media/v4l2-core/v4l2-fwnode.c +7 -3
@@ -145,7 +145,8 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode,u32 v;int rval; -if (bus_type ==V4L2_MBUS_CSI2_DPHY ) { +if (bus_type ==V4L2_MBUS_CSI2_DPHY || + bus_type ==V4L2_MBUS_CSI2_CPHY ) { use_default_lane_mapping = true; num_data_lanes = min_t(u32, bus->num_data_lanes,
@@ -221,10 +222,12 @@ static int v4l2_fwnode_endpoint_parse_csi2_bus(struct fwnode_handle *fwnode, flags |=V4L2_MBUS_CSI2_CONTINUOUS_CLOCK ; } -if (bus_type ==V4L2_MBUS_CSI2_DPHY || lanes_used || +if (bus_type ==V4L2_MBUS_CSI2_DPHY || + bus_type ==V4L2_MBUS_CSI2_CPHY || lanes_used || have_clk_lane || (flags & ~V4L2_MBUS_CSI2_CONTINUOUS_CLOCK )) { bus->flags = flags; - vep->bus_type =V4L2_MBUS_CSI2_DPHY ; +if (bus_type ==V4L2_MBUS_UNKNOWN ) + vep->bus_type =V4L2_MBUS_CSI2_DPHY ; bus->num_data_lanes = num_data_lanes;if (use_default_lane_mapping) {
@@ -468,6 +471,7 @@ static int __v4l2_fwnode_endpoint_parse(struct fwnode_handle *fwnode,break ;case V4L2_MBUS_CSI2_DPHY : +case V4L2_MBUS_CSI2_CPHY : rval =v4l2_fwnode_endpoint_parse_csi2_bus (fwnode, vep, vep->bus_type);if (rval)
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 22/23 v4l: fwnode: Update V4L2 fwnode endpoint parsing documentation
In reply to Sakari AilusThe semantics of v4l2_fwnode_endpoint_parse() and v4l2_fwnode_endpoint_alloc_parse() have changed slightly: they now take the bus type from the user as well as a default configuration for the bus that shall reflect the DT binding defaults. Document this.
--- include/media/v4l2-fwnode.h | 56 ++++++++++++++++++++++++++++++--------------- 1 file changed, 37 insertions(+), 19 deletions(-)
include/media/v4l2-fwnode.h +37 -19
@@ -131,21 +131,30 @@ struct v4l2_fwnode_link {* @fwnode: pointer to the endpoint's fwnode handle * @vep: pointer to the V4L2 fwnode data structure * -* All properties are optional. If none are found, we don't set any flags. This -* means the port has a static configuration and no properties have to be -* specified explicitly. If any properties that identify the bus as parallel -* are found and slave-mode isn't set, we set V4L2_MBUS_MASTER. Similarly, if -* we recognise the bus as serial CSI-2 and clock-noncontinuous isn't set, we -* set the V4L2_MBUS_CSI2_CONTINUOUS_CLOCK flag. The caller should hold a -* reference to @fwnode. -* -* The caller must set the bus_type field of @vep to zero. +* This function parses the V4L2 fwnode endpoint specific parameters from the +* firmware. The caller is responsible for assigning @vep.bus_type to a valid +* media bus type. The caller may also set the default configuration for the +* endpoint --- a configuration that shall be in line with the DT binding +* documentation. Should a device support multiple bus types, the caller may +* call this function once the correct type is found --- with a default +* configuration valid for that type. +* +* As a compatibility means guessing the bus type is also supported by setting +* @vep.bus_type to V4L2_MBUS_UNKNOWN. The caller may not provide a default +* configuration in this case as the defaults are specific to a given bus type. +* This functionality is deprecated and should not be used in new drivers and it +* is only supported for CSI-2 D-PHY, parallel and Bt.656 busses. +* +* The function does not change the V4L2 fwnode endpoint state if it fails. * * NOTE: This function does not parse properties the size of which is variable * without a low fixed limit. Please use v4l2_fwnode_endpoint_alloc_parse() in * new drivers instead. * -* Return: 0 on success or a negative error code on failure. +* Return: %0 on success or a negative error code on failure: +* %-ENOMEM on memory allocation failure +* %-EINVAL on parsing failure +* %-ENXIO on mismatching bus types */ int v4l2_fwnode_endpoint_parse (struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep);
@@ -165,15 +174,21 @@ void v4l2_fwnode_endpoint_free(struct v4l2_fwnode_endpoint *vep);* @fwnode: pointer to the endpoint's fwnode handle * @vep: pointer to the V4L2 fwnode data structure * -* All properties are optional. If none are found, we don't set any flags. This -* means the port has a static configuration and no properties have to be -* specified explicitly. If any properties that identify the bus as parallel -* are found and slave-mode isn't set, we set V4L2_MBUS_MASTER. Similarly, if -* we recognise the bus as serial CSI-2 and clock-noncontinuous isn't set, we -* set the V4L2_MBUS_CSI2_CONTINUOUS_CLOCK flag. The caller should hold a -* reference to @fwnode. +* This function parses the V4L2 fwnode endpoint specific parameters from the +* firmware. The caller is responsible for assigning @vep.bus_type to a valid +* media bus type. The caller may also set the default configuration for the +* endpoint --- a configuration that shall be in line with the DT binding +* documentation. Should a device support multiple bus types, the caller may +* call this function once the correct type is found --- with a default +* configuration valid for that type. +* +* As a compatibility means guessing the bus type is also supported by setting +* @vep.bus_type to V4L2_MBUS_UNKNOWN. The caller may not provide a default +* configuration in this case as the defaults are specific to a given bus type. +* This functionality is deprecated and should not be used in new drivers and it +* is only supported for CSI-2 D-PHY, parallel and Bt.656 busses. * -* The caller must set the bus_type field of @vep to zero. +* The function does not change the V4L2 fwnode endpoint state if it fails. * * v4l2_fwnode_endpoint_alloc_parse() has two important differences to * v4l2_fwnode_endpoint_parse():
@@ -183,7 +198,10 @@ void v4l2_fwnode_endpoint_free(struct v4l2_fwnode_endpoint *vep);* 2. The memory it has allocated to store the variable size data must be freed * using v4l2_fwnode_endpoint_free() when no longer needed. * -* Return: 0 on success or a negative error code on failure. +* Return: %0 on success or a negative error code on failure: +* %-ENOMEM on memory allocation failure +* %-EINVAL on parsing failure +* %-ENXIO on mismatching bus types */ int v4l2_fwnode_endpoint_alloc_parse (struct fwnode_handle *fwnode,struct v4l2_fwnode_endpoint *vep);
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Sakari Ailus
maintainerPATCH v3 23/23 smiapp: Query the V4L2 endpoint for a specific bus type
In reply to Sakari AilusInstead of opportunistically trying to gather some information from the V4L2 endpoint, set the bus type and let the V4L2 fwnode framework figure out the configuration.
--- drivers/media/i2c/smiapp/smiapp-core.c | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/media/i2c/smiapp/smiapp-core.c +6 -0
@@ -2775,7 +2775,13 @@ static struct smiapp_hwconfig *smiapp_get_hwconfig(struct device *dev)if (!ep)return NULL ; + bus_cfg.bus_type =V4L2_MBUS_CSI2_DPHY ; rval =v4l2_fwnode_endpoint_alloc_parse (ep, &bus_cfg); +if (rval == -ENXIO ) { + bus_cfg = (struct v4l2_fwnode_endpoint ) + { .bus_type =V4L2_MBUS_CCP2 }; + rval =v4l2_fwnode_endpoint_alloc_parse (ep, &bus_cfg); + }if (rval) goto out_err;
Signature · 6 lines
2.11.0 _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel
Hi Sakari,
Quoted 34 lines · Sakari Ailus
Hello everyone,
I've long thought the V4L2 fwnode framework requires some work (it's buggy and it does not adequately serve common needs). This set should address in particular these matters:
- Most devices support a particular media bus type but the V4L2 fwnode framework was not able to use such information, but instead tried to guess the bus type with varying levels of success while drivers generally ignored the results. This patchset makes that possible --- setting a bus type enables parsing configuration for only that bus. Failing that check results in returning
-ENXIOto be returned.- Support specifying default configuration. If the endpoint has no configuration, the defaults set by the driver (as documented in DT bindings) will prevail. Any available configuration will still be read from the endpoint as one could expect. A common use case for this is e.g. the number of CSI-2 lanes. Few devices support lane mapping, and default 1:1 mapping is provided in absence of a valid default or configuration read OF.
- Debugging information is greatly improved.
- Recognition of the differences between CSI-2 D-PHY and C-PHY. All currently supported hardware (or at least drivers) is D-PHY only, so this change is still easy.
The smiapp driver is converted to use the new functionality. This patchset does not address remaining issues such as supporting setting defaults for e.g. bridge drivers with multiple ports, but with Steve Longerbeam's patchset we're much closer to that goal. I've rebased this set on top of Steve's. Albeit the two deal with the same files, there were only a few trivial conflicts.
Quoted 3 lines
Note that I've only tested parsing endpoints for the CSI-2 bus (no parallel IF hardware). Jacopo has tested an earlier version of the set with a few changes to the parallel bus handling compared to this one.
I've tested on parallel bus with CEU and MT9V111.
You can add my:
to this version too.
Thanks
j
Quoted 112 lines
Comments are welcome.
I've pushed the patches (including Steve's) here:
<URL:https://git.linuxtv.org/sailus/media_tree.git/log/?h=v4l2-fwnode-next>
since v1:
- Rebase it all on current media tree master --- there was a conflict in
drivers/media/platform/qcom/camss/camss.cin Steve's patch "media:
platform: Switch tov4l2_async_notifier_add_subdev"; I hope the resolution was fine.- Default to Bt.656 bus in guessing the bus type if no properties suggesting otherwise are set. In v1 and error was returned, which would have been troublesome for the existing drivers.
- Set the
bus_typefield to zero (i.e. guess) for existing callers of v4l2_fwnode_endpoint_(alloc_)parse.- Improved documentation for
v4l2_fwnode_endpoint_parseandv4l2_fwnode_endpoint_alloc_parse.since v2:
- Rename
V4L2_MBUS_CSI2toV4L2_MBUS_CSI2_DPHYalso indrivers/gpu/ipu-v3/ipu-csi.c.- Use 0 instead of
V4L2_MBUS_UNKNOWNinv4l2_async_notifier_fwnode_parse_endpoint(). This is partially due toV4L2_MBUS_UNKNOWNbeing introduced after the change is done.- Initialise
bus_typeto zero in quite a few V4L2 fwnode endpoints indrivers/staging/media/imx/imx-media-csi.c(thanks to Steve for the changes).Sakari Ailus (23):
v4l: fwnode: Add debug prints for V4L2 endpoint property parsing
v4l: fwnode: Usefwnode_graph_for_each_endpoint
v4l: fwnode: The CSI-2 clock is continuous if it's not non-continuous
dt-bindings: media: Specify bus type for MIPI D-PHY, others,
explicitly
v4l: fwnode: Add definitions for CSI-2 D-PHY, parallel and Bt.656
busses
v4l: mediabus: Recognise CSI-2 D-PHY and C-PHY
v4l: fwnode: Let the caller provide V4L2 fwnode endpoint
v4l: fwnode: Detect bus type correctly
v4l: fwnode: Make use of newly specified bus types
v4l: fwnode: Read lane inversion information despite lane numbering
v4l: fwnode: Only assign configuration if there is no error
v4l: fwnode: Support driver-defined lane mapping defaults
v4l: fwnode: Support default CSI-2 lane mapping for drivers
v4l: fwnode: Parse the graph endpoint as last
v4l: fwnode: Use default parallel flags
v4l: fwnode: Initialise the V4L2 fwnode endpoints to zero
v4l: fwnode: Only zero the struct if bus type is set to
V4L2_MBUS_UNKNOWN
v4l: fwnode: Use media bus type for bus parser selection
v4l: fwnode: Print bus type
v4l: fwnode: Use V4L2 fwnode endpoint media bus type if set
v4l: fwnode: Support parsing of CSI-2 C-PHY endpoints
v4l: fwnode: Update V4L2 fwnode endpoint parsing documentation
smiapp: Query the V4L2 endpoint for a specific bus type.../devicetree/bindings/media/video-interfaces.txt | 4 +- drivers/gpu/ipu-v3/ipu-csi.c | 6 +- drivers/media/i2c/adv7180.c | 2 +- drivers/media/i2c/adv7604.c | 2 +- drivers/media/i2c/mt9v032.c | 2 +- drivers/media/i2c/ov2659.c | 14 +- drivers/media/i2c/ov5640.c | 4 +- drivers/media/i2c/ov5645.c | 2 +- drivers/media/i2c/ov5647.c | 2 +- drivers/media/i2c/ov7251.c | 4 +- drivers/media/i2c/ov7670.c | 2 +- drivers/media/i2c/s5c73m3/s5c73m3-core.c | 4 +- drivers/media/i2c/s5k5baf.c | 6 +- drivers/media/i2c/s5k6aa.c | 2 +- drivers/media/i2c/smiapp/smiapp-core.c | 34 +- drivers/media/i2c/soc_camera/ov5642.c | 2 +- drivers/media/i2c/tc358743.c | 28 +- drivers/media/i2c/tda1997x.c | 2 +- drivers/media/i2c/tvp514x.c | 2 +- drivers/media/i2c/tvp5150.c | 2 +- drivers/media/i2c/tvp7002.c | 2 +- drivers/media/pci/intel/ipu3/ipu3-cio2.c | 2 +- drivers/media/platform/am437x/am437x-vpfe.c | 2 +- drivers/media/platform/atmel/atmel-isc.c | 3 +- drivers/media/platform/atmel/atmel-isi.c | 2 +- drivers/media/platform/cadence/cdns-csi2rx.c | 4 +- drivers/media/platform/cadence/cdns-csi2tx.c | 4 +- drivers/media/platform/davinci/vpif_capture.c | 2 +- drivers/media/platform/exynos4-is/media-dev.c | 2 +- drivers/media/platform/exynos4-is/mipi-csis.c | 2 +- drivers/media/platform/marvell-ccic/mcam-core.c | 4 +- drivers/media/platform/marvell-ccic/mmp-driver.c | 2 +- drivers/media/platform/omap3isp/isp.c | 2 +- drivers/media/platform/pxa_camera.c | 4 +- drivers/media/platform/rcar-vin/rcar-csi2.c | 4 +- drivers/media/platform/renesas-ceu.c | 3 +- drivers/media/platform/soc_camera/soc_mediabus.c | 2 +- drivers/media/platform/stm32/stm32-dcmi.c | 4 +- drivers/media/platform/ti-vpe/cal.c | 2 +- drivers/media/v4l2-core/v4l2-fwnode.c | 508 ++++++++++++++++----- drivers/staging/media/imx/imx-media-csi.c | 10 +- drivers/staging/media/imx/imx6-mipi-csi2.c | 2 +- drivers/staging/media/imx074/imx074.c | 2 +- include/media/v4l2-fwnode.h | 60 ++- include/media/v4l2-mediabus.h | 8 +- 45 files changed, 542 insertions(+), 226 deletions(-)
Quoted 3 lines
--
2.11.0
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Quoted 41 lines · jacopo mondi
Hi Sakari,
Quoted 34 lines · Sakari Ailus
Hello everyone,
I've long thought the V4L2 fwnode framework requires some work (it's buggy and it does not adequately serve common needs). This set should address in particular these matters:
- Most devices support a particular media bus type but the V4L2 fwnode framework was not able to use such information, but instead tried to guess the bus type with varying levels of success while drivers generally ignored the results. This patchset makes that possible --- setting a bus type enables parsing configuration for only that bus. Failing that check results in returning
-ENXIOto be returned.- Support specifying default configuration. If the endpoint has no configuration, the defaults set by the driver (as documented in DT bindings) will prevail. Any available configuration will still be read from the endpoint as one could expect. A common use case for this is e.g. the number of CSI-2 lanes. Few devices support lane mapping, and default 1:1 mapping is provided in absence of a valid default or configuration read OF.
- Debugging information is greatly improved.
- Recognition of the differences between CSI-2 D-PHY and C-PHY. All currently supported hardware (or at least drivers) is D-PHY only, so this change is still easy.
The smiapp driver is converted to use the new functionality. This patchset does not address remaining issues such as supporting setting defaults for e.g. bridge drivers with multiple ports, but with Steve Longerbeam's patchset we're much closer to that goal. I've rebased this set on top of Steve's. Albeit the two deal with the same files, there were only a few trivial conflicts.
Quoted 3 lines
Note that I've only tested parsing endpoints for the CSI-2 bus (no parallel IF hardware). Jacopo has tested an earlier version of the set with a few changes to the parallel bus handling compared to this one.
Quoted 5 lines
I've tested on parallel bus with CEU and MT9V111.
You can add my:
Tested-by Jacopo Mondi <[email protected]>to this version too.
Thanks!
I'll put your ack on the DT binding documentation patch as Tested-by: isn't really meaningful in that case.
Signature · 6 lines
Sakari Ailus e-mail: [email protected] _______________________________________________ dri-devel mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/dri-devel