thermal: of-thermal: disable passive polling when thermal zone is disabled
PATCH 1/7 thermal: of-thermal: disable passive polling when thermal zone is disabled
From: Anson Huang <[email protected]>
[ Upstream commit 152395fd03d4ce1e535a75cdbf58105e50587611 ]
When thermal zone is in passive mode, disabling its mode from sysfs is NOT taking effect at all, it is still polling the temperature of the disabled thermal zone and handling all thermal trips, it makes user confused. The disabling operation should disable the thermal zone behavior completely, for both active and passive mode, this patch clears the passive_delay when thermal zone is disabled and restores it when it is enabled.
--- drivers/thermal/of-thermal.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/thermal/of-thermal.c +5 -2
@@ -284,10 +284,13 @@ static int of_thermal_set_mode(struct thermal_zone_device *tz,mutex_lock (&tz->lock); -if (mode ==THERMAL_DEVICE_ENABLED ) +if (mode ==THERMAL_DEVICE_ENABLED ) { tz->polling_delay = data->polling_delay; -else + tz->passive_delay = data->passive_delay; + }else { tz->polling_delay =0 ; + tz->passive_delay =0 ; + }mutex_unlock (&tz->lock);
Signature · 1 line
2.17.1
PATCH 2/7 net: hns: fix length and page_offset overflow when CONFIG_ARM64_64K_PAGES
From: Huazhong Tan <[email protected]>
[ Upstream commit 3ed614dce3ca9912d22be215ff0f11104b69fe62 ]
When enable the config item "CONFIG_ARM64_64K_PAGES", the size of PAGE_SIZE is 65536(64K). But the type of length and page_offset are u16, they will overflow. So change them to u32.
--- drivers/net/ethernet/hisilicon/hns/hnae.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/net/ethernet/hisilicon/hns/hnae.h +3 -3
@@ -171,10 +171,10 @@ struct hnae_desc_cb {/* priv data for the desc, e.g. skb when use with ip stack*/ void *priv; -u16 page_offset; -u16 reuse_flag; +u32 page_offset; +u32 length;/* length of the buffer */ -u16 length;/* length of the buffer */ +u16 reuse_flag;/* desc type, used by the ring user to mark the type of the priv data */ u16 type;
Signature · 1 line
2.17.1
PATCH 3/7 e1000: check on netif_running() before calling e1000_up()
In reply to Sasha LevinFrom: Bo Chen <[email protected]>
[ Upstream commit cf1acec008f8d7761aa3fd7c4bca7e17b2d2512d ]
When the device is not up, the call to 'e1000_up()' from the error handling path of 'e1000_set_ringparam()' causes a kernel oops with a null-pointer dereference. The null-pointer dereference is triggered in function 'e1000_alloc_rx_buffers()' at line 'buffer_info = &rx_ring->buffer_info[i]'.
This bug was reported by COD, a tool for testing kernel module binaries I am building. This bug was also detected by KFI from Dr. Kai Cong.
This patch fixes the bug by checking on 'netif_running()' before calling 'e1000_up()' in 'e1000_set_ringparam()'.
--- drivers/net/ethernet/intel/e1000/e1000_ethtool.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/net/ethernet/intel/e1000/e1000_ethtool.c +2 -1
@@ -665,7 +665,8 @@ static int e1000_set_ringparam(struct net_device *netdev, err_alloc_rx:kfree (txdr); err_alloc_tx: -e1000_up (adapter); +if (netif_running (adapter->netdev)) +e1000_up (adapter); err_setup:clear_bit (__E1000_RESETTING, &adapter->flags);return err;
Signature · 1 line
2.17.1
PATCH 4/7 e1000: ensure to free old tx/rx rings in set_ringparam()
In reply to Sasha LevinFrom: Bo Chen <[email protected]>
[ Upstream commit ee400a3f1bfe7004a3e14b81c38ccc5583c26295 ]
In 'e1000_set_ringparam()', the tx_ring and rx_ring are updated with new value and the old tx/rx rings are freed only when the device is up. There are resource leaks on old tx/rx rings when the device is not up. This bug is reported by COD, a tool for testing kernel module binaries I am building.
This patch fixes the bug by always calling 'kfree()' on old tx/rx rings in 'e1000_set_ringparam()'.
--- drivers/net/ethernet/intel/e1000/e1000_ethtool.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/net/ethernet/intel/e1000/e1000_ethtool.c +2 -2
@@ -645,14 +645,14 @@ static int e1000_set_ringparam(struct net_device *netdev, adapter->tx_ring = tx_old;e1000_free_all_rx_resources (adapter);e1000_free_all_tx_resources (adapter); -kfree (tx_old); -kfree (rx_old); adapter->rx_ring = rxdr; adapter->tx_ring = txdr; err =e1000_up (adapter);if (err) goto err_setup; } +kfree (tx_old); +kfree (rx_old);clear_bit (__E1000_RESETTING, &adapter->flags);return 0 ;
Signature · 1 line
2.17.1
PATCH 5/7 hwmon: (ina2xx) fix sysfs shunt resistor read access
In reply to Sasha LevinFrom: Lothar Felten <[email protected]>
[ Upstream commit 3ad867001c91657c46dcf6656d52eb6080286fd5 ]
fix the sysfs shunt resistor read access: return the shunt resistor value, not the calibration register contents.
update email address
--- Documentation/hwmon/ina2xx | 2 +- drivers/hwmon/ina2xx.c | 13 +++++++++++-- include/linux/platform_data/ina2xx.h | 2 +- 3 files changed, 13 insertions(+), 4 deletions(-)
Documentation/hwmon/ina2xx +1 -1
@@ -32,7 +32,7 @@ Supported chips: Datasheet: Publicly available at the Texas Instruments website http://www.ti.com/ -Author: Lothar Felten <[email protected]> +Author: Lothar Felten <[email protected]> Description -----------
drivers/hwmon/ina2xx.c +11 -2
@@ -17,7 +17,7 @@* Bi-directional Current/Power Monitor with I2C Interface * Datasheet: http://www.ti.com/product/ina230 * -* Copyright (C) 2012 Lothar Felten <[email protected]> +* Copyright (C) 2012 Lothar Felten <[email protected]> * Thanks to Jan Volkering * * This program is free software; you can redistribute it and/or modify
@@ -328,6 +328,15 @@ static int ina2xx_set_shunt(struct ina2xx_data *data, long val)return 0 ; } +static ssize_t ina2xx_show_shunt (struct device *dev, +struct device_attribute *da, +char *buf) +{ +struct ina2xx_data *data =dev_get_drvdata (dev); + +return snprintf (buf,PAGE_SIZE ,"%li\n" , data->rshunt); +} +static ssize_t ina2xx_store_shunt (struct device *dev,struct device_attribute *da,const char *buf,size_t count)
@@ -402,7 +411,7 @@ static SENSOR_DEVICE_ATTR(power1_input, S_IRUGO, ina2xx_show_value, NULL,/* shunt resistance */ static SENSOR_DEVICE_ATTR(shunt_resistor, S_IRUGO | S_IWUSR, - ina2xx_show_value, ina2xx_store_shunt, + ina2xx_show_shunt, ina2xx_store_shunt, INA2XX_CALIBRATION);/* update interval (ina226 only) */
include/linux/platform_data/ina2xx.h +1 -1
@@ -1,7 +1,7 @@/* * Driver for Texas Instruments INA219, INA226 power monitor chips * -* Copyright (C) 2012 Lothar Felten <[email protected]> +* Copyright (C) 2012 Lothar Felten <[email protected]> * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as
Signature · 1 line
2.17.1
PATCH 6/7 hwmon: (adt7475) Make adt7475_read_word() return errors
In reply to Sasha LevinFrom: Dan Carpenter <[email protected]>
[ Upstream commit f196dec6d50abb2e65fb54a0621b2f1b4d922995 ]
The adt7475_read_word() function was meant to return negative error codes on failure.
--- drivers/hwmon/adt7475.c | 14 +++++++++----- 1 file changed, 9 insertions(+), 5 deletions(-)
drivers/hwmon/adt7475.c +9 -5
@@ -274,14 +274,18 @@ static inline u16 volt2reg(int channel, long volt, u8 bypass_attn)return clamp_val (reg,0 ,1023 ) & (0xff <<2 ); } -static u16 adt7475_read_word (struct i2c_client *client,int reg) +static int adt7475_read_word (struct i2c_client *client,int reg) { -u16 val; +int val1, val2; - val =i2c_smbus_read_byte_data (client, reg); - val |= (i2c_smbus_read_byte_data (client, reg +1 ) <<8 ); + val1 =i2c_smbus_read_byte_data (client, reg); +if (val1 <0 ) +return val1; + val2 =i2c_smbus_read_byte_data (client, reg +1 ); +if (val2 <0 ) +return val2; -return val; +return val1 | (val2 <<8 ); }static void adt7475_write_word (struct i2c_client *client,int reg,u16 val)
Signature · 1 line
2.17.1
PATCH 7/7 i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus
In reply to Sasha LevinFrom: Mika Westerberg <[email protected]>
[ Upstream commit 7fd6d98b89f382d414e1db528e29a67bbd749457 ]
Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR") made it possible for AML code to access SMBus I/O ports by installing custom SystemIO OpRegion handler and blocking i80i driver access upon first AML read/write to this OpRegion.
However, while ThinkPad T560 does have SystemIO OpRegion declared under the SMBus device, it does not access any of the SMBus registers:
Device (SMBU)
{
...
OperationRegion (SMBP, PCI_Config, 0x50, 0x04)
Field (SMBP, DWordAcc, NoLock, Preserve)
{
, 5,
TCOB, 11,
Offset (0x04)
}
Name (TCBV, 0x00)
Method (TCBS, 0, NotSerialized)
{
If ((TCBV == 0x00))
{
TCBV = (\_SB.PCI0.SMBU.TCOB << 0x05)
}
Return (TCBV) /* \_SB_.PCI0.SMBU.TCBV */
}
OperationRegion (TCBA, SystemIO, TCBS (), 0x10)
Field (TCBA, ByteAcc, NoLock, Preserve)
{
Offset (0x04),
, 9,
CPSC, 1
}
}Problem with the current approach is that it blocks all I/O port access and because this system has touchpad connected to the SMBus controller after first AML access (happens during suspend/resume cycle) the touchpad fails to work anymore.
Fix this so that we allow ACPI AML I/O port access if it does not touch the region reserved for the SMBus.
--- drivers/i2c/busses/i2c-i801.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-)
drivers/i2c/busses/i2c-i801.c +8 -1
@@ -1267,6 +1267,13 @@ static void i801_add_tco(struct i801_priv *priv) }#ifdef CONFIG_ACPI +static bool i801_acpi_is_smbus_ioport (const struct i801_priv *priv, +acpi_physical_address address) +{ +return address >= priv->smba && + address <=pci_resource_end (priv->pci_dev,SMBBAR ); +} +static acpi_status i801_acpi_io_handler (u32 function,acpi_physical_address address,u32 bits,u64 *value,void *handler_context,void *region_context)
@@ -1282,7 +1289,7 @@ i801_acpi_io_handler(u32 function, acpi_physical_address address, u32 bits,*/ mutex_lock (&priv->acpi_lock); -if (!priv->acpi_reserved) { +if (!priv->acpi_reserved &&i801_acpi_is_smbus_ioport (priv, address)) { priv->acpi_reserved = true;dev_warn (&pdev->dev,"BIOS is accessing SMBus registers\n" );
Signature · 1 line
2.17.1