Skip to contentSkip to conversation

net: dsa: b53: SGMII modes fixes

PATCH New Florian Fainelli 1 participant 4 messages Sep 22, 2018

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

cover net: dsa: b53: SGMII modes fixes

Hi David,

Here are two additional fixes that are required in order for SGMII to work correctly. This was discovered with using a copper SFP which would make us use SGMII mode, we would actually leave the HW configured in its default mode: Fiber.

Florian Fainelli (2):
net: dsa: b53: Fix B53_SERDES_DIGITAL_CONTROL offset
net: dsa: b53: Also include SGMII for mac_config and mac_link_state

 drivers/net/dsa/b53/b53_common.c | 10 ++++++----
 drivers/net/dsa/b53/b53_serdes.h |  2 +-
 2 files changed, 7 insertions(+), 5 deletions(-)
Signature · 1 line
2.17.1
#1 lore raw

PATCH 1/1 net: dsa: b53: Don't assign autonegotiation enabled

PHYLINK takes care of filing the right information into state->an_enabled, get rid of the read from the SerDes's BMCR register.

Fixes 0e01491de646 ("net: dsa: b53: Add SerDes support")
---
 drivers/net/dsa/b53/b53_serdes.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/net/dsa/b53/b53_serdes.c +1 -4
index b45c55e0b8b4..629bf14128a2 100644
@@ -100,15 +100,13 @@ int b53_serdes_link_state(struct b53_device *dev, int port,
 			  struct phylink_link_state *state)
 {
 	u8 lane = b53_serdes_map_lane(dev, port);
-	u16 dig, bmcr, bmsr;
+	u16 dig, bmsr;
 
 	if (lane == B53_INVALID_LANE)
 		return 1;
 
 	dig = b53_serdes_read(dev, lane, B53_SERDES_DIGITAL_STATUS,
 			      SERDES_DIGITAL_BLK);
-	bmcr = b53_serdes_read(dev, lane, B53_SERDES_MII_REG(MII_BMCR),
-			       SERDES_MII_BLK);
 	bmsr = b53_serdes_read(dev, lane, B53_SERDES_MII_REG(MII_BMSR),
 			       SERDES_MII_BLK);
 
@@ -129,7 +127,6 @@ int b53_serdes_link_state(struct b53_device *dev, int port,
 	}
 
 	state->duplex = dig & DUPLEX_STATUS ? DUPLEX_FULL : DUPLEX_HALF;
-	state->an_enabled = !!(bmcr & BMCR_ANENABLE);
 	state->an_complete = !!(bmsr & BMSR_ANEGCOMPLETE);
 	state->link = !!(dig & LINK_STATUS);
 	if (dig & PAUSE_RESOLUTION_RX_SIDE)
Signature · 1 line
2.17.1
#2 lore raw

PATCH 1/2 net: dsa: b53: Fix B53_SERDES_DIGITAL_CONTROL offset

In reply to Florian Fainelli

Maths went wrong, to get 0x20, we need to do 0x1e + (x) * 2, not 0x18, fix that offset so we access the correct registers. This would make us not access the correct SerDes Digital control words, status would be fine and so we would not be correctly flipping between Fiber and SGMII modes resulting in incorrect status words being pulled into the SerDes digital status register.

Fixes 0e01491de646 ("net: dsa: b53: Add SerDes support")
---
 drivers/net/dsa/b53/b53_serdes.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/dsa/b53/b53_serdes.h +1 -1
index eed7c9357091..3bb4f91aec9e 100644
@@ -20,7 +20,7 @@
 #define  SERDES_ID0_REV_LETTER_SHIFT	14
 
 #define B53_SERDES_MII_REG(x)		(0x20 + (x) * 2)
-#define B53_SERDES_DIGITAL_CONTROL(x)	(0x18 + (x) * 2)
+#define B53_SERDES_DIGITAL_CONTROL(x)	(0x1e + (x) * 2)
 #define B53_SERDES_DIGITAL_STATUS	0x28
 
 /* SERDES_DIGITAL_CONTROL1 */
Signature · 1 line
2.17.1
#3 lore raw

PATCH 2/2 net: dsa: b53: Also include SGMII for mac_config and mac_link_state

In reply to Florian Fainelli

In both 802.3z and SGMII modes we need to configure the MAC accordingly to flip between Fiber and SGMII modes, and we need to read the MAC status from the SGMII in-band control word.

Fixes 0e01491de646 ("net: dsa: b53: Add SerDes support")
---
 drivers/net/dsa/b53/b53_common.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/net/dsa/b53/b53_common.c +6 -4
index dbf5b86a07fe..700d86dd5e13 100644
@@ -1172,8 +1172,9 @@ int b53_phylink_mac_link_state(struct dsa_switch *ds, int port,
 	struct b53_device *dev = ds->priv;
 	int ret = -EOPNOTSUPP;
 
-	if (phy_interface_mode_is_8023z(state->interface) &&
-	    dev->ops->serdes_link_state)
+	if ((phy_interface_mode_is_8023z(state->interface) ||
+	     state->interface == PHY_INTERFACE_MODE_SGMII) &&
+	     dev->ops->serdes_link_state)
 		ret = dev->ops->serdes_link_state(dev, port, state);
 
 	return ret;
@@ -1195,8 +1196,9 @@ void b53_phylink_mac_config(struct dsa_switch *ds, int port,
 		return;
 	}
 
-	if (phy_interface_mode_is_8023z(state->interface) &&
-	    dev->ops->serdes_config)
+	if ((phy_interface_mode_is_8023z(state->interface) ||
+	     state->interface == PHY_INTERFACE_MODE_SGMII) &&
+	     dev->ops->serdes_config)
 		dev->ops->serdes_config(dev, port, mode, state);
 }
 EXPORT_SYMBOL(b53_phylink_mac_config);
Signature · 1 line
2.17.1