Skip to contentSkip to conversation

mac80211: Run TXQ teardown code before de-registering interfaces

PATCH New Sasha Levin 1 participant 75 messages Sep 24, 2018 Stable branch

lore
Share & tools
lore
#0 lore raw

PATCH 1/76 mac80211: Run TXQ teardown code before de-registering interfaces

From: Toke Høiland-Jørgensen <[email protected]>

[ Upstream commit 77cfaf52eca5cac30ed029507e0cab065f888995 ]

The TXQ teardown code can reference the vif data structures that are stored in the netdev private memory area if there are still packets on the queue when it is being freed. Since the TXQ teardown code is run after the netdevs are freed, this can lead to a use-after-free. Fix this by moving the TXQ teardown code to earlier in ieee80211_unregister_hw().

---
 net/mac80211/main.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/mac80211/main.c +1 -1
index fb73451ed85e..0358f20b675f 100644
@@ -1182,6 +1182,7 @@ void ieee80211_unregister_hw(struct ieee80211_hw *hw)
 #if IS_ENABLED(CONFIG_IPV6)
 	unregister_inet6addr_notifier(&local->ifa6_notifier);
 #endif
+	ieee80211_txq_teardown_flows(local);
 
 	rtnl_lock();
 
@@ -1210,7 +1211,6 @@ void ieee80211_unregister_hw(struct ieee80211_hw *hw)
 	skb_queue_purge(&local->skb_queue);
 	skb_queue_purge(&local->skb_queue_unreliable);
 	skb_queue_purge(&local->skb_queue_tdls_chsw);
-	ieee80211_txq_teardown_flows(local);
 
 	destroy_workqueue(local->workqueue);
 	wiphy_unregister(local->hw.wiphy);
Signature · 1 line
2.17.1
#1 lore raw

PATCH 2/76 mac80211_hwsim: require at least one channel

From: Johannes Berg <[email protected]>

[ Upstream commit 484004339d4514fde425f6e8a9f6a6cc979bb0c3 ]

Syzbot continues to try to create mac80211_hwsim radios, and manages to pass parameters that are later checked with WARN_ON in cfg80211 - catch another one in hwsim directly.

---
 drivers/net/wireless/mac80211_hwsim.c | 5 +++++
 1 file changed, 5 insertions(+)
drivers/net/wireless/mac80211_hwsim.c +5 -0
index 18e819d964f1..fe1b0108f06d 100644
@@ -3194,6 +3194,11 @@ static int hwsim_new_radio_nl(struct sk_buff *msg, struct genl_info *info)
 	if (info->attrs[HWSIM_ATTR_CHANNELS])
 		param.channels = nla_get_u32(info->attrs[HWSIM_ATTR_CHANNELS]);
 
+	if (param.channels < 1) {
+		GENL_SET_ERR_MSG(info, "must have at least one channel");
+		return -EINVAL;
+	}
+
 	if (param.channels > CFG80211_MAX_NUM_DIFFERENT_CHANNELS) {
 		GENL_SET_ERR_MSG(info, "too many channels specified");
 		return -EINVAL;
Signature · 1 line
2.17.1
#2 lore raw

PATCH 3/76 Btrfs: fix unexpected failure of nocow buffered writes after snapshotting when low on space

In reply to Sasha Levin

From: Robbie Ko <[email protected]>

[ Upstream commit 8ecebf4d767e2307a946c8905278d6358eda35c3 ]

Commit e9894fd3e3b3 ("Btrfs: fix snapshot vs nocow writting") forced nocow writes to fallback to COW, during writeback, when a snapshot is created. This resulted in writes made before creating the snapshot to unexpectedly fail with ENOSPC during writeback when success (0) was returned to user space through the write system call.

The steps leading to this problem are:

1. When it's not possible to allocate data space for a write, the buffered write path checks if a NOCOW write is possible. If it is, it will not reserve space and success (0) is returned to user space.

2. Then when a snapshot is created, the root's will_be_snapshotted atomic is incremented and writeback is triggered for all inode's that belong to the root being snapshotted. Incrementing that atomic forces all previous writes to fallback to COW during writeback (running delalloc).

3. This results in the writeback for the inodes to fail and therefore setting the ENOSPC error in their mappings, so that a subsequent fsync on them will report the error to user space. So it's not a completely silent data loss (since fsync will report ENOSPC) but it's a very unexpected and undesirable behaviour, because if a clean shutdown/unmount of the filesystem happens without previous calls to fsync, it is expected to have the data present in the files after mounting the filesystem again.

So fix this by adding a new atomic named snapshot_force_cow to the root structure which prevents this behaviour and works the following way:

1. It is incremented when we start to create a snapshot after triggering writeback and before waiting for writeback to finish.

2. This new atomic is now what is used by writeback (running delalloc) to decide whether we need to fallback to COW or not. Because we incremented this new atomic after triggering writeback in the snapshot creation ioctl, we ensure that all buffered writes that happened before snapshot creation will succeed and not fallback to COW (which would make them fail with ENOSPC).

3. The existing atomic, will_be_snapshotted, is kept because it is used to force new buffered writes, that start after we started snapshotting, to reserve data space even when NOCOW is possible. This makes these writes fail early with ENOSPC when there's no available space to allocate, preventing the unexpected behaviour of writeback later failing with ENOSPC due to a fallback to COW mode.

Fixes e9894fd3e3b3 ("Btrfs: fix snapshot vs nocow writting")
---
 fs/btrfs/ctree.h   |  1 +
 fs/btrfs/disk-io.c |  1 +
 fs/btrfs/inode.c   | 25 ++++---------------------
 fs/btrfs/ioctl.c   | 16 ++++++++++++++++
 4 files changed, 22 insertions(+), 21 deletions(-)
fs/btrfs/ctree.h +1 -0
index 118346aceea9..663ce0518d27 100644
@@ -1277,6 +1277,7 @@ struct btrfs_root {
 	int send_in_progress;
 	struct btrfs_subvolume_writers *subv_writers;
 	atomic_t will_be_snapshotted;
+	atomic_t snapshot_force_cow;
 
 	/* For qgroup metadata reserved space */
 	spinlock_t qgroup_meta_rsv_lock;
fs/btrfs/disk-io.c +1 -0
index dfed08e70ec1..891b1aab3480 100644
@@ -1217,6 +1217,7 @@ static void __setup_root(struct btrfs_root *root, struct btrfs_fs_info *fs_info,
 	atomic_set(&root->log_batch, 0);
 	refcount_set(&root->refs, 1);
 	atomic_set(&root->will_be_snapshotted, 0);
+	atomic_set(&root->snapshot_force_cow, 0);
 	root->log_transid = 0;
 	root->log_transid_committed = -1;
 	root->last_log_commit = 0;
fs/btrfs/inode.c +4 -21
index 071d949f69ec..d3736fbf6774 100644
@@ -1275,7 +1275,7 @@ static noinline int run_delalloc_nocow(struct inode *inode,
 	u64 disk_num_bytes;
 	u64 ram_bytes;
 	int extent_type;
-	int ret, err;
+	int ret;
 	int type;
 	int nocow;
 	int check_prev = 1;
@@ -1407,11 +1407,8 @@ static noinline int run_delalloc_nocow(struct inode *inode,
 			 * if there are pending snapshots for this root,
 			 * we fall into common COW way.
 			 */
-			if (!nolock) {
-				err = btrfs_start_write_no_snapshotting(root);
-				if (!err)
-					goto out_check;
-			}
+			if (!nolock && atomic_read(&root->snapshot_force_cow))
+				goto out_check;
 			/*
 			 * force cow if csum exists in the range.
 			 * this ensure that csum for a given extent are
@@ -1420,9 +1417,6 @@ static noinline int run_delalloc_nocow(struct inode *inode,
 			ret = csum_exist_in_range(fs_info, disk_bytenr,
 						  num_bytes);
 			if (ret) {
-				if (!nolock)
-					btrfs_end_write_no_snapshotting(root);
-
 				/*
 				 * ret could be -EIO if the above fails to read
 				 * metadata.
@@ -1435,11 +1429,8 @@ static noinline int run_delalloc_nocow(struct inode *inode,
 				WARN_ON_ONCE(nolock);
 				goto out_check;
 			}
-			if (!btrfs_inc_nocow_writers(fs_info, disk_bytenr)) {
-				if (!nolock)
-					btrfs_end_write_no_snapshotting(root);
+			if (!btrfs_inc_nocow_writers(fs_info, disk_bytenr))
 				goto out_check;
-			}
 			nocow = 1;
 		} else if (extent_type == BTRFS_FILE_EXTENT_INLINE) {
 			extent_end = found_key.offset +
@@ -1453,8 +1444,6 @@ static noinline int run_delalloc_nocow(struct inode *inode,
 out_check:
 		if (extent_end <= start) {
 			path->slots[0]++;
-			if (!nolock && nocow)
-				btrfs_end_write_no_snapshotting(root);
 			if (nocow)
 				btrfs_dec_nocow_writers(fs_info, disk_bytenr);
 			goto next_slot;
@@ -1476,8 +1465,6 @@ static noinline int run_delalloc_nocow(struct inode *inode,
 					     end, page_started, nr_written, 1,
 					     NULL);
 			if (ret) {
-				if (!nolock && nocow)
-					btrfs_end_write_no_snapshotting(root);
 				if (nocow)
 					btrfs_dec_nocow_writers(fs_info,
 								disk_bytenr);
@@ -1497,8 +1484,6 @@ static noinline int run_delalloc_nocow(struct inode *inode,
 					  ram_bytes, BTRFS_COMPRESS_NONE,
 					  BTRFS_ORDERED_PREALLOC);
 			if (IS_ERR(em)) {
-				if (!nolock && nocow)
-					btrfs_end_write_no_snapshotting(root);
 				if (nocow)
 					btrfs_dec_nocow_writers(fs_info,
 								disk_bytenr);
@@ -1537,8 +1522,6 @@ static noinline int run_delalloc_nocow(struct inode *inode,
 					     EXTENT_CLEAR_DATA_RESV,
 					     PAGE_UNLOCK | PAGE_SET_PRIVATE2);
 
-		if (!nolock && nocow)
-			btrfs_end_write_no_snapshotting(root);
 		cur_offset = extent_end;
 
 		/*
fs/btrfs/ioctl.c +16 -0
index f3d6be0c657b..ef7159646615 100644
@@ -761,6 +761,7 @@ static int create_snapshot(struct btrfs_root *root, struct inode *dir,
 	struct btrfs_pending_snapshot *pending_snapshot;
 	struct btrfs_trans_handle *trans;
 	int ret;
+	bool snapshot_force_cow = false;
 
 	if (!test_bit(BTRFS_ROOT_REF_COWS, &root->state))
 		return -EINVAL;
@@ -777,6 +778,11 @@ static int create_snapshot(struct btrfs_root *root, struct inode *dir,
 		goto free_pending;
 	}
 
+	/*
+	 * Force new buffered writes to reserve space even when NOCOW is
+	 * possible. This is to avoid later writeback (running dealloc) to
+	 * fallback to COW mode and unexpectedly fail with ENOSPC.
+	 */
 	atomic_inc(&root->will_be_snapshotted);
 	smp_mb__after_atomic();
 	/* wait for no snapshot writes */
@@ -787,6 +793,14 @@ static int create_snapshot(struct btrfs_root *root, struct inode *dir,
 	if (ret)
 		goto dec_and_free;
 
+	/*
+	 * All previous writes have started writeback in NOCOW mode, so now
+	 * we force future writes to fallback to COW mode during snapshot
+	 * creation.
+	 */
+	atomic_inc(&root->snapshot_force_cow);
+	snapshot_force_cow = true;
+
 	btrfs_wait_ordered_extents(root, U64_MAX, 0, (u64)-1);
 
 	btrfs_init_block_rsv(&pending_snapshot->block_rsv,
@@ -851,6 +865,8 @@ static int create_snapshot(struct btrfs_root *root, struct inode *dir,
 fail:
 	btrfs_subvolume_release_metadata(fs_info, &pending_snapshot->block_rsv);
 dec_and_free:
+	if (snapshot_force_cow)
+		atomic_dec(&root->snapshot_force_cow);
 	if (atomic_dec_and_test(&root->will_be_snapshotted))
 		wake_up_var(&root->will_be_snapshotted);
 free_pending:
Signature · 1 line
2.17.1
#3 lore raw

PATCH 4/76 KVM: PPC: Book3S HV: Don't truncate HPTE index in xlate function

In reply to Sasha Levin

From: Paul Mackerras <[email protected]>

[ Upstream commit 46dec40fb741f00f1864580130779aeeaf24fb3d ]

This fixes a bug which causes guest virtual addresses to get translated to guest real addresses incorrectly when the guest is using the HPT MMU and has more than 256GB of RAM, or more specifically has a HPT larger than 2GB. This has showed up in testing as a failure of the host to emulate doorbell instructions correctly on POWER9 for HPT guests with more than 256GB of RAM.

The bug is that the HPTE index in kvmppc_mmu_book3s_64_hv_xlate() is stored as an int, and in forming the HPTE address, the index gets shifted left 4 bits as an int before being signed-extended to 64 bits. The simple fix is to make the variable a long int, matching the return type of kvmppc_hv_find_lock_hpte(), which is what calculates the index.

Fixes 697d3899dcb4 ("KVM: PPC: Implement MMIO emulation support for Book3S HV guests")
---
 arch/powerpc/kvm/book3s_64_mmu_hv.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/powerpc/kvm/book3s_64_mmu_hv.c +1 -1
index 7f3a8cf5d66f..4c08f42f6406 100644
@@ -359,7 +359,7 @@ static int kvmppc_mmu_book3s_64_hv_xlate(struct kvm_vcpu *vcpu, gva_t eaddr,
 	unsigned long pp, key;
 	unsigned long v, orig_v, gr;
 	__be64 *hptep;
-	int index;
+	long int index;
 	int virtmode = vcpu->arch.shregs.msr & (data ? MSR_DR : MSR_IR);
 
 	if (kvm_is_radix(vcpu->kvm))
Signature · 1 line
2.17.1
#4 lore raw

PATCH 5/76 cfg80211: remove division by size of sizeof(struct ieee80211_wmm_rule)

In reply to Sasha Levin

From: Johannes Berg <[email protected]>

[ Upstream commit 8a54d8fc160e67ad485d95a0322ce1221f80770a ]

Pointer arithmetic already adjusts by the size of the struct, so the sizeof() calculation is wrong. This is basically the same as Colin King's patch for similar code in the iwlwifi driver.

Fixes 230ebaa189af ("cfg80211: read wmm rules from regulatory database")
---
 net/wireless/reg.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
net/wireless/reg.c +1 -2
index 4fc66a117b7d..283902974fbf 100644
@@ -452,8 +452,7 @@ reg_copy_regd(const struct ieee80211_regdomain *src_regd)
 			continue;
 
 		regd->reg_rules[i].wmm_rule = d_wmm +
-			(src_regd->reg_rules[i].wmm_rule - s_wmm) /
-			sizeof(struct ieee80211_wmm_rule);
+			(src_regd->reg_rules[i].wmm_rule - s_wmm);
 	}
 	return regd;
 }
Signature · 1 line
2.17.1
#5 lore raw

PATCH 6/76 btrfs: btrfs_shrink_device should call commit transaction at the end

In reply to Sasha Levin

From: Anand Jain <[email protected]>

[ Upstream commit 801660b040d132f67fac6a95910ad307c5929b49 ]

Test case btrfs/164 reports use-after-free:

[ 6712.084324] general protection fault: 0000 [#1] PREEMPT SMP
..
[ 6712.195423]  btrfs_update_commit_device_size+0x75/0xf0 [btrfs]
[ 6712.201424]  btrfs_commit_transaction+0x57d/0xa90 [btrfs]
[ 6712.206999]  btrfs_rm_device+0x627/0x850 [btrfs]
[ 6712.211800]  btrfs_ioctl+0x2b03/0x3120 [btrfs]

Reason for this is that btrfs_shrink_device adds the resized device to the fs_devices::resized_devices after it has called the last commit transaction.

So the list fs_devices::resized_devices is not empty when btrfs_shrink_device returns. Now the parent function btrfs_rm_device calls:

        btrfs_close_bdev(device);
        call_rcu(&device->rcu, free_device_rcu);

and then does the transactio ncommit. It goes through the fs_devices::resized_devices in btrfs_update_commit_device_size and leads to use-after-free.

Fix this by making sure btrfs_shrink_device calls the last needed btrfs_commit_transaction before the return. This is consistent with what the grow counterpart does and this makes sure the on-disk state is persistent when the function returns.

---
 fs/btrfs/volumes.c | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)
fs/btrfs/volumes.c +6 -1
index 5304b8d6ceb8..1a22c0ecaf67 100644
@@ -4584,7 +4584,12 @@ int btrfs_shrink_device(struct btrfs_device *device, u64 new_size)
 
 	/* Now btrfs_update_device() will change the on-disk size. */
 	ret = btrfs_update_device(trans, device);
-	btrfs_end_transaction(trans);
+	if (ret < 0) {
+		btrfs_abort_transaction(trans, ret);
+		btrfs_end_transaction(trans);
+	} else {
+		ret = btrfs_commit_transaction(trans);
+	}
 done:
 	btrfs_free_path(path);
 	if (ret) {
Signature · 1 line
2.17.1
#6 lore raw

PATCH 7/76 scsi: csiostor: add a check for NULL pointer after kmalloc()

In reply to Sasha Levin

From: Varun Prakash <[email protected]>

[ Upstream commit 89809b028b6f54187b7d81a0c69b35d394c52e62 ]

---
 drivers/scsi/csiostor/csio_hw.c | 16 +++++++++-------
 1 file changed, 9 insertions(+), 7 deletions(-)
drivers/scsi/csiostor/csio_hw.c +9 -7
index a10cf25ee7f9..1ee255a62f1b 100644
@@ -2275,8 +2275,8 @@ static int csio_hw_prep_fw(struct csio_hw *hw, struct fw_info *fw_info,
 }
 
 /*
- * Returns -EINVAL if attempts to flash the firmware failed
- * else returns 0,
+ * Returns -EINVAL if attempts to flash the firmware failed,
+ * -ENOMEM if memory allocation failed else returns 0,
  * if flashing was not attempted because the card had the
  * latest firmware ECANCELED is returned
  */
@@ -2304,6 +2304,13 @@ csio_hw_flash_fw(struct csio_hw *hw, int *reset)
 		return -EINVAL;
 	}
 
+	/* allocate memory to read the header of the firmware on the
+	 * card
+	 */
+	card_fw = kmalloc(sizeof(*card_fw), GFP_KERNEL);
+	if (!card_fw)
+		return -ENOMEM;
+
 	if (csio_is_t5(pci_dev->device & CSIO_HW_CHIP_MASK))
 		fw_bin_file = FW_FNAME_T5;
 	else
@@ -2317,11 +2324,6 @@ csio_hw_flash_fw(struct csio_hw *hw, int *reset)
 		fw_size = fw->size;
 	}
 
-	/* allocate memory to read the header of the firmware on the
-	 * card
-	 */
-	card_fw = kmalloc(sizeof(*card_fw), GFP_KERNEL);
-
 	/* upgrade FW logic */
 	ret = csio_hw_prep_fw(hw, fw_info, fw_data, fw_size, card_fw,
 			 hw->fw_state, reset);
Signature · 1 line
2.17.1
#7 lore raw

PATCH 8/76 scsi: csiostor: fix incorrect port capabilities

In reply to Sasha Levin

From: Varun Prakash <[email protected]>

[ Upstream commit 68bdc630721c40e908d22cffe07b5ca225a69f6e ]

- use be32_to_cpu() instead of ntohs() for 32 bit port capabilities.

- add a new function fwcaps32_to_caps16() to convert 32 bit port capabilities to 16 bit port capabilities.

---
 drivers/scsi/csiostor/csio_hw.c | 55 ++++++++++++++++++++++++++-------
 drivers/scsi/csiostor/csio_hw.h |  1 +
 drivers/scsi/csiostor/csio_mb.c |  6 ++--
 3 files changed, 48 insertions(+), 14 deletions(-)
drivers/scsi/csiostor/csio_hw.c +44 -11
index 1ee255a62f1b..e4baf04ec5ea 100644
@@ -1512,6 +1512,46 @@ fw_port_cap32_t fwcaps16_to_caps32(fw_port_cap16_t caps16)
 	return caps32;
 }
 
+/**
+ *	fwcaps32_to_caps16 - convert 32-bit Port Capabilities to 16-bits
+ *	@caps32: a 32-bit Port Capabilities value
+ *
+ *	Returns the equivalent 16-bit Port Capabilities value.  Note that
+ *	not all 32-bit Port Capabilities can be represented in the 16-bit
+ *	Port Capabilities and some fields/values may not make it.
+ */
+fw_port_cap16_t fwcaps32_to_caps16(fw_port_cap32_t caps32)
+{
+	fw_port_cap16_t caps16 = 0;
+
+	#define CAP32_TO_CAP16(__cap) \
+		do { \
+			if (caps32 & FW_PORT_CAP32_##__cap) \
+				caps16 |= FW_PORT_CAP_##__cap; \
+		} while (0)
+
+	CAP32_TO_CAP16(SPEED_100M);
+	CAP32_TO_CAP16(SPEED_1G);
+	CAP32_TO_CAP16(SPEED_10G);
+	CAP32_TO_CAP16(SPEED_25G);
+	CAP32_TO_CAP16(SPEED_40G);
+	CAP32_TO_CAP16(SPEED_100G);
+	CAP32_TO_CAP16(FC_RX);
+	CAP32_TO_CAP16(FC_TX);
+	CAP32_TO_CAP16(802_3_PAUSE);
+	CAP32_TO_CAP16(802_3_ASM_DIR);
+	CAP32_TO_CAP16(ANEG);
+	CAP32_TO_CAP16(FORCE_PAUSE);
+	CAP32_TO_CAP16(MDIAUTO);
+	CAP32_TO_CAP16(MDISTRAIGHT);
+	CAP32_TO_CAP16(FEC_RS);
+	CAP32_TO_CAP16(FEC_BASER_RS);
+
+	#undef CAP32_TO_CAP16
+
+	return caps16;
+}
+
 /**
  *      lstatus_to_fwcap - translate old lstatus to 32-bit Port Capabilities
  *      @lstatus: old FW_PORT_ACTION_GET_PORT_INFO lstatus value
@@ -1670,7 +1710,7 @@ csio_enable_ports(struct csio_hw *hw)
 			val = 1;
 
 			csio_mb_params(hw, mbp, CSIO_MB_DEFAULT_TMO,
-				       hw->pfn, 0, 1, &param, &val, false,
+				       hw->pfn, 0, 1, &param, &val, true,
 				       NULL);
 
 			if (csio_mb_issue(hw, mbp)) {
@@ -1680,16 +1720,9 @@ csio_enable_ports(struct csio_hw *hw)
 				return -EINVAL;
 			}
 
-			csio_mb_process_read_params_rsp(hw, mbp, &retval, 1,
-							&val);
-			if (retval != FW_SUCCESS) {
-				csio_err(hw, "FW_PARAMS_CMD(r) port:%d failed: 0x%x\n",
-					 portid, retval);
-				mempool_free(mbp, hw->mb_mempool);
-				return -EINVAL;
-			}
-
-			fw_caps = val;
+			csio_mb_process_read_params_rsp(hw, mbp, &retval,
+							0, NULL);
+			fw_caps = retval ? FW_CAPS16 : FW_CAPS32;
 		}
 
 		/* Read PORT information */
drivers/scsi/csiostor/csio_hw.h +1 -0
index 9e73ef771eb7..e351af6e7c81 100644
@@ -639,6 +639,7 @@ int csio_handle_intr_status(struct csio_hw *, unsigned int,
 
 fw_port_cap32_t fwcap_to_fwspeed(fw_port_cap32_t acaps);
 fw_port_cap32_t fwcaps16_to_caps32(fw_port_cap16_t caps16);
+fw_port_cap16_t fwcaps32_to_caps16(fw_port_cap32_t caps32);
 fw_port_cap32_t lstatus_to_fwcap(u32 lstatus);
 
 int csio_hw_start(struct csio_hw *);
drivers/scsi/csiostor/csio_mb.c +3 -3
index c026417269c3..6f13673d6aa0 100644
@@ -368,7 +368,7 @@ csio_mb_port(struct csio_hw *hw, struct csio_mb *mbp, uint32_t tmo,
 			FW_CMD_LEN16_V(sizeof(*cmdp) / 16));
 
 	if (fw_caps == FW_CAPS16)
-		cmdp->u.l1cfg.rcap = cpu_to_be32(fc);
+		cmdp->u.l1cfg.rcap = cpu_to_be32(fwcaps32_to_caps16(fc));
 	else
 		cmdp->u.l1cfg32.rcap32 = cpu_to_be32(fc);
 }
@@ -395,8 +395,8 @@ csio_mb_process_read_port_rsp(struct csio_hw *hw, struct csio_mb *mbp,
 			*pcaps = fwcaps16_to_caps32(ntohs(rsp->u.info.pcap));
 			*acaps = fwcaps16_to_caps32(ntohs(rsp->u.info.acap));
 		} else {
-			*pcaps = ntohs(rsp->u.info32.pcaps32);
-			*acaps = ntohs(rsp->u.info32.acaps32);
+			*pcaps = be32_to_cpu(rsp->u.info32.pcaps32);
+			*acaps = be32_to_cpu(rsp->u.info32.acaps32);
 		}
 	}
 }
Signature · 1 line
2.17.1
#8 lore raw

PATCH 9/76 scsi: libata: Add missing newline at end of file

In reply to Sasha Levin

From: Geert Uytterhoeven <[email protected]>

[ Upstream commit 4e8065aa6c6f50765290be27ab8a64a4e44cb009 ]

With gcc 4.1.2:

drivers/ata/libata-core.c:7396:33: warning: no newline at end of file

Fixes 2fa4a32613c9182b ("scsi: libsas: dynamically allocate and free ata host")
---
 drivers/ata/libata-core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/ata/libata-core.c +1 -1
index 984b37647b2f..c26dba0ee3ce 100644
@@ -7393,4 +7393,4 @@ EXPORT_SYMBOL_GPL(ata_cable_unknown);
 EXPORT_SYMBOL_GPL(ata_cable_ignore);
 EXPORT_SYMBOL_GPL(ata_cable_sata);
 EXPORT_SYMBOL_GPL(ata_host_get);
-EXPORT_SYMBOL_GPL(ata_host_put);
\ No newline at end of file
+EXPORT_SYMBOL_GPL(ata_host_put);
Signature · 1 line
2.17.1
#9 lore raw

PATCH 10/76 scsi: aacraid: fix a signedness bug

In reply to Sasha Levin

From: Dan Carpenter <[email protected]>

[ Upstream commit b9eb3b14f1dbf16bf27b6c1ffe6b8c00ec945c9b ]

The problem is that ->reset_state is a u8 but it can be set to -1 or -2 in aac_tmf_callback() and the error handling in aac_eh_target_reset() relies on it to be signed.

[mkp: fixed typo]

Fixes 0d643ff3c353 ("scsi: aacraid: use aac_tmf_callback for reset fib")
---
 drivers/scsi/aacraid/aacraid.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/scsi/aacraid/aacraid.h +1 -1
index 29bf1e60f542..39eb415987fc 100644
@@ -1346,7 +1346,7 @@ struct fib {
 struct aac_hba_map_info {
 	__le32	rmw_nexus;		/* nexus for native HBA devices */
 	u8		devtype;	/* device type */
-	u8		reset_state;	/* 0 - no reset, 1..x - */
+	s8		reset_state;	/* 0 - no reset, 1..x - */
 					/* after xth TM LUN reset */
 	u16		qd_limit;
 	u32		scan_counter;
Signature · 1 line
2.17.1
#10 lore raw

PATCH 11/76 bpf, sockmap: fix potential use after free in bpf_tcp_close

In reply to Sasha Levin

From: Daniel Borkmann <[email protected]>

[ Upstream commit e06fa9c16ce4b740996189fa5610eabcee734e6c ]

bpf_tcp_close() we pop the psock linkage to a map via psock_map_pop(). A parallel update on the sock hash map can happen between psock_map_pop() and lookup_elem_raw() where we override the element under link->hash / link->key. In bpf_tcp_close()'s lookup_elem_raw() we subsequently only test whether an element is present, but we do not test whether the element is infact the element we were looking for.

We lock the sock in bpf_tcp_close() during that time, so do we hold the lock in sock_hash_update_elem(). However, the latter locks the sock which is newly updated, not the one we're purging from the hash table. This means that while one CPU is doing the lookup from bpf_tcp_close(), another CPU is doing the map update in parallel, dropped our sock from the hlist and released the psock.

Subsequently the first CPU will find the new sock and attempts to drop and release the old sock yet another time. Fix is that we need to check the elements for a match after lookup, similar as we do in the sock map. Note that the hash tab elems are freed via RCU, so access to their link->hash / link->key is fine since we're under RCU read side there.

Fixes e9db4ef6bf4c ("bpf: sockhash fix omitted bucket lock in sock_close")
---
 kernel/bpf/sockmap.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
kernel/bpf/sockmap.c +1 -1
index 58899601fccf..7afa2a54ee34 100644
@@ -369,7 +369,7 @@ static void bpf_tcp_close(struct sock *sk, long timeout)
 			/* If another thread deleted this object skip deletion.
 			 * The refcnt on psock may or may not be zero.
 			 */
-			if (l) {
+			if (l && l == link) {
 				hlist_del_rcu(&link->hash_node);
 				smap_release_sock(psock, link->sk);
 				free_htab_elem(htab, link);
Signature · 1 line
2.17.1
#11 lore raw

PATCH 12/76 bpf, sockmap: fix psock refcount leak in bpf_tcp_recvmsg

In reply to Sasha Levin

From: Daniel Borkmann <[email protected]>

[ Upstream commit 15c480efab01197c965ce0562a43ffedd852b8f9 ]

In bpf_tcp_recvmsg() we first took a reference on the psock, however once we find that there are skbs in the normal socket's receive queue we return with processing them through tcp_recvmsg(). Problem is that we leak the taken reference on the psock in that path. Given we don't really do anything with the psock at this point, move the skb_queue_empty() test before we fetch the psock to fix this case.

Fixes 8934ce2fd081 ("bpf: sockmap redirect ingress support")
---
 kernel/bpf/sockmap.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
kernel/bpf/sockmap.c +2 -3
index 7afa2a54ee34..e43730b52ea6 100644
@@ -915,6 +915,8 @@ static int bpf_tcp_recvmsg(struct sock *sk, struct msghdr *msg, size_t len,
 
 	if (unlikely(flags & MSG_ERRQUEUE))
 		return inet_recv_error(sk, msg, len, addr_len);
+	if (!skb_queue_empty(&sk->sk_receive_queue))
+		return tcp_recvmsg(sk, msg, len, nonblock, flags, addr_len);
 
 	rcu_read_lock();
 	psock = smap_psock_sk(sk);
@@ -925,9 +927,6 @@ static int bpf_tcp_recvmsg(struct sock *sk, struct msghdr *msg, size_t len,
 		goto out;
 	rcu_read_unlock();
 
-	if (!skb_queue_empty(&sk->sk_receive_queue))
-		return tcp_recvmsg(sk, msg, len, nonblock, flags, addr_len);
-
 	lock_sock(sk);
 bytes_ready:
 	while (copied != len) {
Signature · 1 line
2.17.1
#12 lore raw

PATCH 13/76 bpf: sockmap, decrement copied count correctly in redirect error case

In reply to Sasha Levin

From: John Fastabend <[email protected]>

[ Upstream commit 501ca81760c204ec59b73e4a00bee5971fc0f1b1 ]

Currently, when a redirect occurs in sockmap and an error occurs in the redirect call we unwind the scatterlist once in the error path of bpf_tcp_sendmsg_do_redirect() and then again in sendmsg(). Then in the error path of sendmsg we decrement the copied count by the send size.

However, its possible we partially sent data before the error was generated. This can happen if do_tcp_sendpages() partially sends the scatterlist before encountering a memory pressure error. If this happens we need to decrement the copied value (the value tracking how many bytes were actually sent to TCP stack) by the number of remaining bytes _not_ the entire send size. Otherwise we risk confusing userspace.

Also we don't need two calls to free the scatterlist one is good enough. So remove the one in bpf_tcp_sendmsg_do_redirect() and then properly reduce copied by the number of remaining bytes which may in fact be the entire send size if no bytes were sent.

To do this use bool to indicate if free_start_sg() should do mem accounting or not.

---
 kernel/bpf/sockmap.c | 45 ++++++++++++++++++++++----------------------
 1 file changed, 22 insertions(+), 23 deletions(-)
kernel/bpf/sockmap.c +22 -23
index e43730b52ea6..2ddf1501aace 100644
@@ -236,7 +236,7 @@ static int bpf_tcp_init(struct sock *sk)
 }
 
 static void smap_release_sock(struct smap_psock *psock, struct sock *sock);
-static int free_start_sg(struct sock *sk, struct sk_msg_buff *md);
+static int free_start_sg(struct sock *sk, struct sk_msg_buff *md, bool charge);
 
 static void bpf_tcp_release(struct sock *sk)
 {
@@ -248,7 +248,7 @@ static void bpf_tcp_release(struct sock *sk)
 		goto out;
 
 	if (psock->cork) {
-		free_start_sg(psock->sock, psock->cork);
+		free_start_sg(psock->sock, psock->cork, true);
 		kfree(psock->cork);
 		psock->cork = NULL;
 	}
@@ -330,14 +330,14 @@ static void bpf_tcp_close(struct sock *sk, long timeout)
 	close_fun = psock->save_close;
 
 	if (psock->cork) {
-		free_start_sg(psock->sock, psock->cork);
+		free_start_sg(psock->sock, psock->cork, true);
 		kfree(psock->cork);
 		psock->cork = NULL;
 	}
 
 	list_for_each_entry_safe(md, mtmp, &psock->ingress, list) {
 		list_del(&md->list);
-		free_start_sg(psock->sock, md);
+		free_start_sg(psock->sock, md, true);
 		kfree(md);
 	}
 
@@ -570,14 +570,16 @@ static void free_bytes_sg(struct sock *sk, int bytes,
 	md->sg_start = i;
 }
 
-static int free_sg(struct sock *sk, int start, struct sk_msg_buff *md)
+static int free_sg(struct sock *sk, int start,
+		   struct sk_msg_buff *md, bool charge)
 {
 	struct scatterlist *sg = md->sg_data;
 	int i = start, free = 0;
 
 	while (sg[i].length) {
 		free += sg[i].length;
-		sk_mem_uncharge(sk, sg[i].length);
+		if (charge)
+			sk_mem_uncharge(sk, sg[i].length);
 		if (!md->skb)
 			put_page(sg_page(&sg[i]));
 		sg[i].length = 0;
@@ -594,9 +596,9 @@ static int free_sg(struct sock *sk, int start, struct sk_msg_buff *md)
 	return free;
 }
 
-static int free_start_sg(struct sock *sk, struct sk_msg_buff *md)
+static int free_start_sg(struct sock *sk, struct sk_msg_buff *md, bool charge)
 {
-	int free = free_sg(sk, md->sg_start, md);
+	int free = free_sg(sk, md->sg_start, md, charge);
 
 	md->sg_start = md->sg_end;
 	return free;
@@ -604,7 +606,7 @@ static int free_start_sg(struct sock *sk, struct sk_msg_buff *md)
 
 static int free_curr_sg(struct sock *sk, struct sk_msg_buff *md)
 {
-	return free_sg(sk, md->sg_curr, md);
+	return free_sg(sk, md->sg_curr, md, true);
 }
 
 static int bpf_map_msg_verdict(int _rc, struct sk_msg_buff *md)
@@ -718,7 +720,7 @@ static int bpf_tcp_ingress(struct sock *sk, int apply_bytes,
 		list_add_tail(&r->list, &psock->ingress);
 		sk->sk_data_ready(sk);
 	} else {
-		free_start_sg(sk, r);
+		free_start_sg(sk, r, true);
 		kfree(r);
 	}
 
@@ -755,14 +757,10 @@ static int bpf_tcp_sendmsg_do_redirect(struct sock *sk, int send,
 		release_sock(sk);
 	}
 	smap_release_sock(psock, sk);
-	if (unlikely(err))
-		goto out;
-	return 0;
+	return err;
 out_rcu:
 	rcu_read_unlock();
-out:
-	free_bytes_sg(NULL, send, md, false);
-	return err;
+	return 0;
 }
 
 static inline void bpf_md_init(struct smap_psock *psock)
@@ -825,7 +823,7 @@ static int bpf_exec_tx_verdict(struct smap_psock *psock,
 	case __SK_PASS:
 		err = bpf_tcp_push(sk, send, m, flags, true);
 		if (unlikely(err)) {
-			*copied -= free_start_sg(sk, m);
+			*copied -= free_start_sg(sk, m, true);
 			break;
 		}
 
@@ -848,16 +846,17 @@ static int bpf_exec_tx_verdict(struct smap_psock *psock,
 		lock_sock(sk);
 
 		if (unlikely(err < 0)) {
-			free_start_sg(sk, m);
+			int free = free_start_sg(sk, m, false);
+
 			psock->sg_size = 0;
 			if (!cork)
-				*copied -= send;
+				*copied -= free;
 		} else {
 			psock->sg_size -= send;
 		}
 
 		if (cork) {
-			free_start_sg(sk, m);
+			free_start_sg(sk, m, true);
 			psock->sg_size = 0;
 			kfree(m);
 			m = NULL;
@@ -1124,7 +1123,7 @@ static int bpf_tcp_sendmsg(struct sock *sk, struct msghdr *msg, size_t size)
 		err = sk_stream_wait_memory(sk, &timeo);
 		if (err) {
 			if (m && m != psock->cork)
-				free_start_sg(sk, m);
+				free_start_sg(sk, m, true);
 			goto out_err;
 		}
 	}
@@ -1580,13 +1579,13 @@ static void smap_gc_work(struct work_struct *w)
 		bpf_prog_put(psock->bpf_tx_msg);
 
 	if (psock->cork) {
-		free_start_sg(psock->sock, psock->cork);
+		free_start_sg(psock->sock, psock->cork, true);
 		kfree(psock->cork);
 	}
 
 	list_for_each_entry_safe(md, mtmp, &psock->ingress, list) {
 		list_del(&md->list);
-		free_start_sg(psock->sock, md);
+		free_start_sg(psock->sock, md, true);
 		kfree(md);
 	}
 
Signature · 1 line
2.17.1
#13 lore raw

PATCH 14/76 mac80211: correct use of IEEE80211_VHT_CAP_RXSTBC_X

In reply to Sasha Levin

From: Danek Duvall <[email protected]>

[ Upstream commit 67d1ba8a6dc83d90cd58b89fa6cbf9ae35a0cf7f ]

The mod mask for VHT capabilities intends to say that you can override the number of STBC receive streams, and it does, but only by accident. The IEEE80211_VHT_CAP_RXSTBC_X aren't bits to be set, but values (albeit left-shifted). ORing the bits together gets the right answer, but we should use the _MASK macro here instead.

---
 net/mac80211/main.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)
net/mac80211/main.c +1 -4
index 0358f20b675f..27cd64acaf00 100644
@@ -470,10 +470,7 @@ static const struct ieee80211_vht_cap mac80211_vht_capa_mod_mask = {
 		cpu_to_le32(IEEE80211_VHT_CAP_RXLDPC |
 			    IEEE80211_VHT_CAP_SHORT_GI_80 |
 			    IEEE80211_VHT_CAP_SHORT_GI_160 |
-			    IEEE80211_VHT_CAP_RXSTBC_1 |
-			    IEEE80211_VHT_CAP_RXSTBC_2 |
-			    IEEE80211_VHT_CAP_RXSTBC_3 |
-			    IEEE80211_VHT_CAP_RXSTBC_4 |
+			    IEEE80211_VHT_CAP_RXSTBC_MASK |
 			    IEEE80211_VHT_CAP_TXSTBC |
 			    IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE |
 			    IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE |
Signature · 1 line
2.17.1
#14 lore raw

PATCH 15/76 mac80211_hwsim: correct use of IEEE80211_VHT_CAP_RXSTBC_X

In reply to Sasha Levin

From: Danek Duvall <[email protected]>

[ Upstream commit d7c863a2f65e48f442379f4ee1846d52e0c5d24d ]

The mac80211_hwsim driver intends to say that it supports up to four STBC receive streams, but instead it ends up saying something undefined. The IEEE80211_VHT_CAP_RXSTBC_X macros aren't independent bits that can be ORed together, but values. In this case, _4 is the appropriate one to use.

---
 drivers/net/wireless/mac80211_hwsim.c | 3 ---
 1 file changed, 3 deletions(-)
drivers/net/wireless/mac80211_hwsim.c +0 -3
index fe1b0108f06d..7d0b460868f9 100644
@@ -2699,9 +2699,6 @@ static int mac80211_hwsim_new_radio(struct genl_info *info,
 				IEEE80211_VHT_CAP_SHORT_GI_80 |
 				IEEE80211_VHT_CAP_SHORT_GI_160 |
 				IEEE80211_VHT_CAP_TXSTBC |
-				IEEE80211_VHT_CAP_RXSTBC_1 |
-				IEEE80211_VHT_CAP_RXSTBC_2 |
-				IEEE80211_VHT_CAP_RXSTBC_3 |
 				IEEE80211_VHT_CAP_RXSTBC_4 |
 				IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK;
 			sband->vht_cap.vht_mcs.rx_mcs_map =
Signature · 1 line
2.17.1
#15 lore raw

PATCH 16/76 cfg80211: make wmm_rule part of the reg_rule structure

In reply to Sasha Levin

From: Stanislaw Gruszka <[email protected]>

[ Upstream commit 38cb87ee47fb825f6c9d645c019f75b3905c0ab2 ]

Make wmm_rule be part of the reg_rule structure. This simplifies the code a lot at the cost of having bigger memory usage. However in most cases we have only few reg_rule's and when we do have many like in iwlwifi we do not save memory as it allocates a separate wmm_rule for each channel anyway.

This also fixes a bug reported in various places where somewhere the pointers were corrupted and we ended up doing a null-dereference.

Fixes 230ebaa189af ("cfg80211: read wmm rules from regulatory database")
[rephrase commit message slightly]
---
 .../wireless/intel/iwlwifi/iwl-nvm-parse.c    | 50 ++---------
 include/net/cfg80211.h                        |  4 +-
 include/net/regulatory.h                      |  4 +-
 net/mac80211/util.c                           |  8 +-
 net/wireless/nl80211.c                        | 10 +--
 net/wireless/reg.c                            | 90 +++----------------
 6 files changed, 31 insertions(+), 135 deletions(-)
drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c +5 -45
index b815ba38dbdb..88121548eb9f 100644
@@ -877,15 +877,12 @@ iwl_parse_nvm_mcc_info(struct device *dev, const struct iwl_cfg *cfg,
 	const u8 *nvm_chan = cfg->nvm_type == IWL_NVM_EXT ?
 			     iwl_ext_nvm_channels : iwl_nvm_channels;
 	struct ieee80211_regdomain *regd, *copy_rd;
-	int size_of_regd, regd_to_copy, wmms_to_copy;
-	int size_of_wmms = 0;
+	int size_of_regd, regd_to_copy;
 	struct ieee80211_reg_rule *rule;
-	struct ieee80211_wmm_rule *wmm_rule, *d_wmm, *s_wmm;
 	struct regdb_ptrs *regdb_ptrs;
 	enum nl80211_band band;
 	int center_freq, prev_center_freq = 0;
-	int valid_rules = 0, n_wmms = 0;
-	int i;
+	int valid_rules = 0;
 	bool new_rule;
 	int max_num_ch = cfg->nvm_type == IWL_NVM_EXT ?
 			 IWL_NVM_NUM_CHANNELS_EXT : IWL_NVM_NUM_CHANNELS;
@@ -904,11 +901,7 @@ iwl_parse_nvm_mcc_info(struct device *dev, const struct iwl_cfg *cfg,
 		sizeof(struct ieee80211_regdomain) +
 		num_of_ch * sizeof(struct ieee80211_reg_rule);
 
-	if (geo_info & GEO_WMM_ETSI_5GHZ_INFO)
-		size_of_wmms =
-			num_of_ch * sizeof(struct ieee80211_wmm_rule);
-
-	regd = kzalloc(size_of_regd + size_of_wmms, GFP_KERNEL);
+	regd = kzalloc(size_of_regd, GFP_KERNEL);
 	if (!regd)
 		return ERR_PTR(-ENOMEM);
 
@@ -922,8 +915,6 @@ iwl_parse_nvm_mcc_info(struct device *dev, const struct iwl_cfg *cfg,
 	regd->alpha2[0] = fw_mcc >> 8;
 	regd->alpha2[1] = fw_mcc & 0xff;
 
-	wmm_rule = (struct ieee80211_wmm_rule *)((u8 *)regd + size_of_regd);
-
 	for (ch_idx = 0; ch_idx < num_of_ch; ch_idx++) {
 		ch_flags = (u16)__le32_to_cpup(channels + ch_idx);
 		band = (ch_idx < NUM_2GHZ_CHANNELS) ?
@@ -977,26 +968,10 @@ iwl_parse_nvm_mcc_info(struct device *dev, const struct iwl_cfg *cfg,
 		    band == NL80211_BAND_2GHZ)
 			continue;
 
-		if (!reg_query_regdb_wmm(regd->alpha2, center_freq,
-					 &regdb_ptrs[n_wmms].token, wmm_rule)) {
-			/* Add only new rules */
-			for (i = 0; i < n_wmms; i++) {
-				if (regdb_ptrs[i].token ==
-				    regdb_ptrs[n_wmms].token) {
-					rule->wmm_rule = regdb_ptrs[i].rule;
-					break;
-				}
-			}
-			if (i == n_wmms) {
-				rule->wmm_rule = wmm_rule;
-				regdb_ptrs[n_wmms++].rule = wmm_rule;
-				wmm_rule++;
-			}
-		}
+		reg_query_regdb_wmm(regd->alpha2, center_freq, rule);
 	}
 
 	regd->n_reg_rules = valid_rules;
-	regd->n_wmm_rules = n_wmms;
 
 	/*
 	 * Narrow down regdom for unused regulatory rules to prevent hole
@@ -1005,28 +980,13 @@ iwl_parse_nvm_mcc_info(struct device *dev, const struct iwl_cfg *cfg,
 	regd_to_copy = sizeof(struct ieee80211_regdomain) +
 		valid_rules * sizeof(struct ieee80211_reg_rule);
 
-	wmms_to_copy = sizeof(struct ieee80211_wmm_rule) * n_wmms;
-
-	copy_rd = kzalloc(regd_to_copy + wmms_to_copy, GFP_KERNEL);
+	copy_rd = kzalloc(regd_to_copy, GFP_KERNEL);
 	if (!copy_rd) {
 		copy_rd = ERR_PTR(-ENOMEM);
 		goto out;
 	}
 
 	memcpy(copy_rd, regd, regd_to_copy);
-	memcpy((u8 *)copy_rd + regd_to_copy, (u8 *)regd + size_of_regd,
-	       wmms_to_copy);
-
-	d_wmm = (struct ieee80211_wmm_rule *)((u8 *)copy_rd + regd_to_copy);
-	s_wmm = (struct ieee80211_wmm_rule *)((u8 *)regd + size_of_regd);
-
-	for (i = 0; i < regd->n_reg_rules; i++) {
-		if (!regd->reg_rules[i].wmm_rule)
-			continue;
-
-		copy_rd->reg_rules[i].wmm_rule = d_wmm +
-			(regd->reg_rules[i].wmm_rule - s_wmm);
-	}
 
 out:
 	kfree(regdb_ptrs);
include/net/cfg80211.h +2 -2
index 1beb3ead0385..7229c186d199 100644
@@ -4763,8 +4763,8 @@ const char *reg_initiator_name(enum nl80211_reg_initiator initiator);
  *
  * Return: 0 on success. -ENODATA.
  */
-int reg_query_regdb_wmm(char *alpha2, int freq, u32 *ptr,
-			struct ieee80211_wmm_rule *rule);
+int reg_query_regdb_wmm(char *alpha2, int freq,
+			struct ieee80211_reg_rule *rule);
 
 /*
  * callbacks for asynchronous cfg80211 methods, notification
include/net/regulatory.h +2 -2
index 60f8cc86a447..3469750df0f4 100644
@@ -217,15 +217,15 @@ struct ieee80211_wmm_rule {
 struct ieee80211_reg_rule {
 	struct ieee80211_freq_range freq_range;
 	struct ieee80211_power_rule power_rule;
-	struct ieee80211_wmm_rule *wmm_rule;
+	struct ieee80211_wmm_rule wmm_rule;
 	u32 flags;
 	u32 dfs_cac_ms;
+	bool has_wmm;
 };
 
 struct ieee80211_regdomain {
 	struct rcu_head rcu_head;
 	u32 n_reg_rules;
-	u32 n_wmm_rules;
 	char alpha2[3];
 	enum nl80211_dfs_regions dfs_region;
 	struct ieee80211_reg_rule reg_rules[];
net/mac80211/util.c +4 -4
index d02fbfec3783..c80187d6e6bb 100644
@@ -1120,7 +1120,7 @@ void ieee80211_regulatory_limit_wmm_params(struct ieee80211_sub_if_data *sdata,
 {
 	struct ieee80211_chanctx_conf *chanctx_conf;
 	const struct ieee80211_reg_rule *rrule;
-	struct ieee80211_wmm_ac *wmm_ac;
+	const struct ieee80211_wmm_ac *wmm_ac;
 	u16 center_freq = 0;
 
 	if (sdata->vif.type != NL80211_IFTYPE_AP &&
@@ -1139,15 +1139,15 @@ void ieee80211_regulatory_limit_wmm_params(struct ieee80211_sub_if_data *sdata,
 
 	rrule = freq_reg_info(sdata->wdev.wiphy, MHZ_TO_KHZ(center_freq));
 
-	if (IS_ERR_OR_NULL(rrule) || !rrule->wmm_rule) {
+	if (IS_ERR_OR_NULL(rrule) || !rrule->has_wmm) {
 		rcu_read_unlock();
 		return;
 	}
 
 	if (sdata->vif.type == NL80211_IFTYPE_AP)
-		wmm_ac = &rrule->wmm_rule->ap[ac];
+		wmm_ac = &rrule->wmm_rule.ap[ac];
 	else
-		wmm_ac = &rrule->wmm_rule->client[ac];
+		wmm_ac = &rrule->wmm_rule.client[ac];
 	qparam->cw_min = max_t(u16, qparam->cw_min, wmm_ac->cw_min);
 	qparam->cw_max = max_t(u16, qparam->cw_max, wmm_ac->cw_max);
 	qparam->aifs = max_t(u8, qparam->aifs, wmm_ac->aifsn);
net/wireless/nl80211.c +5 -5
index 80bc986c79e5..e3dcffd96919 100644
@@ -667,13 +667,13 @@ static int nl80211_msg_put_wmm_rules(struct sk_buff *msg,
 			goto nla_put_failure;
 
 		if (nla_put_u16(msg, NL80211_WMMR_CW_MIN,
-				rule->wmm_rule->client[j].cw_min) ||
+				rule->wmm_rule.client[j].cw_min) ||
 		    nla_put_u16(msg, NL80211_WMMR_CW_MAX,
-				rule->wmm_rule->client[j].cw_max) ||
+				rule->wmm_rule.client[j].cw_max) ||
 		    nla_put_u8(msg, NL80211_WMMR_AIFSN,
-			       rule->wmm_rule->client[j].aifsn) ||
+			       rule->wmm_rule.client[j].aifsn) ||
 		    nla_put_u8(msg, NL80211_WMMR_TXOP,
-			       rule->wmm_rule->client[j].cot))
+			       rule->wmm_rule.client[j].cot))
 			goto nla_put_failure;
 
 		nla_nest_end(msg, nl_wmm_rule);
@@ -766,7 +766,7 @@ static int nl80211_msg_put_channel(struct sk_buff *msg, struct wiphy *wiphy,
 		const struct ieee80211_reg_rule *rule =
 			freq_reg_info(wiphy, chan->center_freq);
 
-		if (!IS_ERR(rule) && rule->wmm_rule) {
+		if (!IS_ERR_OR_NULL(rule) && rule->has_wmm) {
 			if (nl80211_msg_put_wmm_rules(msg, rule))
 				goto nla_put_failure;
 		}
net/wireless/reg.c +13 -77

173 lines not on this page · raw message

Signature · 1 line
2.17.1
#16 lore raw

PATCH 17/76 mac80211_hwsim: Fix possible Spectre-v1 for hwsim_world_regdom_custom

In reply to Sasha Levin

From: Jinbum Park <[email protected]>

[ Upstream commit 3a2af7cccbbaf2362db9053a946a6084e12bfa73 ]

User controls @idx which to be used as index of hwsim_world_regdom_custom. So, It can be exploited via Spectre-like attack. (speculative execution)

This kind of attack leaks address of hwsim_world_regdom_custom, It leads an attacker to bypass security mechanism such as KASLR.

So sanitize @idx before using it to prevent attack.

I leveraged strategy [1] to find and exploit this gadget.

[1] https://github.com/jinb-park/linux-exploit/tree/master/exploit-remaining-spectre-gadget/

---
 drivers/net/wireless/mac80211_hwsim.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/net/wireless/mac80211_hwsim.c +4 -0
index 7d0b460868f9..80e2c8595c7c 100644
@@ -33,6 +33,7 @@
 #include <net/net_namespace.h>
 #include <net/netns/generic.h>
 #include <linux/rhashtable.h>
+#include <linux/nospec.h>
 #include "mac80211_hwsim.h"
 
 #define WARN_QUEUE 100
@@ -3229,6 +3230,9 @@ static int hwsim_new_radio_nl(struct sk_buff *msg, struct genl_info *info)
 			kfree(hwname);
 			return -EINVAL;
 		}
+
+		idx = array_index_nospec(idx,
+					 ARRAY_SIZE(hwsim_world_regdom_custom));
 		param.regd = hwsim_world_regdom_custom[idx];
 	}
 
Signature · 1 line
2.17.1
#17 lore raw

PATCH 18/76 nl80211: Fix nla_put_u8 to u16 for NL80211_WMMR_TXOP

In reply to Sasha Levin

From: Haim Dreyfuss <[email protected]>

[ Upstream commit d3c89bbc7491d5e288ca2993e999d24ba9ff52ad ]

TXOP (also known as Channel Occupancy Time) is u16 and should be added using nla_put_u16 instead of u8, fix that.

Fixes 50f32718e125 ("nl80211: Add wmm rule attribute to NL80211_CMD_GET_WIPHY dump command")
---
 net/wireless/nl80211.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
net/wireless/nl80211.c +2 -2
index e3dcffd96919..3f7ffbe6c634 100644
@@ -672,8 +672,8 @@ static int nl80211_msg_put_wmm_rules(struct sk_buff *msg,
 				rule->wmm_rule.client[j].cw_max) ||
 		    nla_put_u8(msg, NL80211_WMMR_AIFSN,
 			       rule->wmm_rule.client[j].aifsn) ||
-		    nla_put_u8(msg, NL80211_WMMR_TXOP,
-			       rule->wmm_rule.client[j].cot))
+		    nla_put_u16(msg, NL80211_WMMR_TXOP,
+			        rule->wmm_rule.client[j].cot))
 			goto nla_put_failure;
 
 		nla_nest_end(msg, nl_wmm_rule);
Signature · 1 line
2.17.1
#18 lore raw

PATCH 19/76 nl80211: Pass center frequency in kHz instead of MHz

In reply to Sasha Levin

From: Haim Dreyfuss <[email protected]>

[ Upstream commit b88d26d97c41680f7327e5fb8061ad0037877f40 ]

freq_reg_info expects to get the frequency in kHz. Instead we accidently pass it in MHz. Thus, currently the function always return ERR rule. Fix that.

Fixes 50f32718e125 ("nl80211: Add wmm rule attribute to NL80211_CMD_GET_WIPHY dump command")
[fix kHz/MHz in commit message]
---
 net/wireless/nl80211.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/wireless/nl80211.c +1 -1
index 3f7ffbe6c634..ce0149a86c13 100644
@@ -764,7 +764,7 @@ static int nl80211_msg_put_channel(struct sk_buff *msg, struct wiphy *wiphy,
 
 	if (large) {
 		const struct ieee80211_reg_rule *rule =
-			freq_reg_info(wiphy, chan->center_freq);
+			freq_reg_info(wiphy, MHZ_TO_KHZ(chan->center_freq));
 
 		if (!IS_ERR_OR_NULL(rule) && rule->has_wmm) {
 			if (nl80211_msg_put_wmm_rules(msg, rule))
Signature · 1 line
2.17.1
#19 lore raw

PATCH 20/76 bpf: fix several offset tests in bpf_msg_pull_data

In reply to Sasha Levin

From: Daniel Borkmann <[email protected]>

[ Upstream commit 5b24109b0563d45094c470684c1f8cea1af269f8 ]

While recently going over bpf_msg_pull_data(), I noticed three issues which are fixed in here:

1) When we attempt to find the first scatterlist element (sge) for the start offset, we add len to the offset before we check for start < offset + len, whereas it should come after when we iterate to the next sge to accumulate the offsets. For example, given a start offset of 12 with a sge length of 8 for the first sge in the list would lead us to determine this sge as the first sge thinking it covers first 16 bytes where start is located, whereas start sits in subsequent sges so we would end up pulling in the wrong data.

2) After figuring out the starting sge, we have a short-cut test in !msg->sg_copy[i] && bytes <= len. This checks whether it's not needed to make the page at the sge private where we can just exit by updating msg->data and msg->data_end. However, the length test is not fully correct. bytes <= len checks whether the requested bytes (end - start offsets) fit into the sge's length. The part that is missing is that start must not be sge length aligned. Meaning, the start offset into the sge needs to be accounted as well on top of the requested bytes as otherwise we can access the sge out of bounds. For example the sge could have length of 8, our requested bytes could have length of 8, but at a start offset of 4, so we also would need to pull in 4 bytes of the next sge, when we jump to the out label we do set msg->data to sg_virt(&sg[i]) + start - offset and msg->data_end to msg->data + bytes which would be oob.

3) The subsequent bytes < copy test for finding the last sge has the same issue as in point 2) but also it tests for less than rather than less or equal to. Meaning if the sge length is of 8 and requested bytes of 8 while having the start aligned with the sge, we would unnecessarily go and pull in the next sge as well to make it private.

Fixes 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
---
 net/core/filter.c | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
net/core/filter.c +9 -5
index 9dfd145eedcc..a9f8d71575c7 100644
@@ -2276,10 +2276,10 @@ BPF_CALL_4(bpf_msg_pull_data,
 	   struct sk_msg_buff *, msg, u32, start, u32, end, u64, flags)
 {
 	unsigned int len = 0, offset = 0, copy = 0;
+	int bytes = end - start, bytes_sg_total;
 	struct scatterlist *sg = msg->sg_data;
 	int first_sg, last_sg, i, shift;
 	unsigned char *p, *to, *from;
-	int bytes = end - start;
 	struct page *page;
 
 	if (unlikely(flags || end <= start))
@@ -2289,9 +2289,9 @@ BPF_CALL_4(bpf_msg_pull_data,
 	i = msg->sg_start;
 	do {
 		len = sg[i].length;
-		offset += len;
 		if (start < offset + len)
 			break;
+		offset += len;
 		i++;
 		if (i == MAX_SKB_FRAGS)
 			i = 0;
@@ -2300,7 +2300,11 @@ BPF_CALL_4(bpf_msg_pull_data,
 	if (unlikely(start >= offset + len))
 		return -EINVAL;
 
-	if (!msg->sg_copy[i] && bytes <= len)
+	/* The start may point into the sg element so we need to also
+	 * account for the headroom.
+	 */
+	bytes_sg_total = start - offset + bytes;
+	if (!msg->sg_copy[i] && bytes_sg_total <= len)
 		goto out;
 
 	first_sg = i;
@@ -2320,12 +2324,12 @@ BPF_CALL_4(bpf_msg_pull_data,
 		i++;
 		if (i == MAX_SKB_FRAGS)
 			i = 0;
-		if (bytes < copy)
+		if (bytes_sg_total <= copy)
 			break;
 	} while (i != msg->sg_end);
 	last_sg = i;
 
-	if (unlikely(copy < end - start))
+	if (unlikely(bytes_sg_total > copy))
 		return -EINVAL;
 
 	page = alloc_pages(__GFP_NOWARN | GFP_ATOMIC, get_order(copy));
Signature · 1 line
2.17.1
#20 lore raw

PATCH 21/76 gpio: adp5588: Fix sleep-in-atomic-context bug

In reply to Sasha Levin

From: Michael Hennerich <[email protected]>

[ Upstream commit 6537886cdc9a637711fd6da980dbb87c2c87c9aa ]

This fixes:
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug

                          in adp5588_gpio_write()
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
                          in adp5588_gpio_direction_input()
---
 drivers/gpio/gpio-adp5588.c | 24 ++++++++++++++++++++----
 1 file changed, 20 insertions(+), 4 deletions(-)
drivers/gpio/gpio-adp5588.c +20 -4
index 3530ccd17e04..da9781a2ef4a 100644
@@ -41,6 +41,8 @@ struct adp5588_gpio {
 	uint8_t int_en[3];
 	uint8_t irq_mask[3];
 	uint8_t irq_stat[3];
+	uint8_t int_input_en[3];
+	uint8_t int_lvl_cached[3];
 };
 
 static int adp5588_gpio_read(struct i2c_client *client, u8 reg)
@@ -173,12 +175,28 @@ static void adp5588_irq_bus_sync_unlock(struct irq_data *d)
 	struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
 	int i;
 
-	for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++)
+	for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) {
+		if (dev->int_input_en[i]) {
+			mutex_lock(&dev->lock);
+			dev->dir[i] &= ~dev->int_input_en[i];
+			dev->int_input_en[i] = 0;
+			adp5588_gpio_write(dev->client, GPIO_DIR1 + i,
+					   dev->dir[i]);
+			mutex_unlock(&dev->lock);
+		}
+
+		if (dev->int_lvl_cached[i] != dev->int_lvl[i]) {
+			dev->int_lvl_cached[i] = dev->int_lvl[i];
+			adp5588_gpio_write(dev->client, GPIO_INT_LVL1 + i,
+					   dev->int_lvl[i]);
+		}
+
 		if (dev->int_en[i] ^ dev->irq_mask[i]) {
 			dev->int_en[i] = dev->irq_mask[i];
 			adp5588_gpio_write(dev->client, GPIO_INT_EN1 + i,
 					   dev->int_en[i]);
 		}
+	}
 
 	mutex_unlock(&dev->irq_lock);
 }
@@ -221,9 +239,7 @@ static int adp5588_irq_set_type(struct irq_data *d, unsigned int type)
 	else
 		return -EINVAL;
 
-	adp5588_gpio_direction_input(&dev->gpio_chip, gpio);
-	adp5588_gpio_write(dev->client, GPIO_INT_LVL1 + bank,
-			   dev->int_lvl[bank]);
+	dev->int_input_en[bank] |= bit;
 
 	return 0;
 }
Signature · 1 line
2.17.1
#21 lore raw

PATCH 22/76 mac80211: mesh: fix HWMP sequence numbering to follow standard

In reply to Sasha Levin

From: Yuan-Chi Pang <[email protected]>

[ Upstream commit 1f631c3201fe5491808df143d8fcba81b3197ffd ]

IEEE 802.11-2016 14.10.8.3 HWMP sequence numbering says:
If it is a target mesh STA, it shall update its own HWMP SN to maximum (current HWMP SN, target HWMP SN in the PREQ element) + 1 immediately before it generates a PREP element in response to a PREQ element.

---
 net/mac80211/mesh_hwmp.c | 4 ++++
 1 file changed, 4 insertions(+)
net/mac80211/mesh_hwmp.c +4 -0
index 35ad3983ae4b..daf9db3c8f24 100644
@@ -572,6 +572,10 @@ static void hwmp_preq_frame_process(struct ieee80211_sub_if_data *sdata,
 		forward = false;
 		reply = true;
 		target_metric = 0;
+
+		if (SN_GT(target_sn, ifmsh->sn))
+			ifmsh->sn = target_sn;
+
 		if (time_after(jiffies, ifmsh->last_sn_update +
 					net_traversal_jiffies(sdata)) ||
 		    time_before(jiffies, ifmsh->last_sn_update)) {
Signature · 1 line
2.17.1
#22 lore raw

PATCH 23/76 mac80211: avoid kernel panic when building AMSDU from non-linear SKB

In reply to Sasha Levin

From: Sara Sharon <[email protected]>

[ Upstream commit 166ac9d55b0ab70b644e429be1f217fe8393cbd7 ]

When building building AMSDU from non-linear SKB, we hit a kernel panic when trying to push the padding to the tail. Instead, put the padding at the head of the next subframe. This also fixes the A-MSDU subframes to not have the padding accounted in the length field and not have pad at all for the last subframe, both required by the spec.

Fixes 6e0456b54545 ("mac80211: add A-MSDU tx support")
---
 net/mac80211/tx.c | 38 +++++++++++++++++++++-----------------
 1 file changed, 21 insertions(+), 17 deletions(-)
net/mac80211/tx.c +21 -17
index fa1f1e63a264..667a73d6eb5c 100644
@@ -3073,27 +3073,18 @@ void ieee80211_clear_fast_xmit(struct sta_info *sta)
 }
 
 static bool ieee80211_amsdu_realloc_pad(struct ieee80211_local *local,
-					struct sk_buff *skb, int headroom,
-					int *subframe_len)
+					struct sk_buff *skb, int headroom)
 {
-	int amsdu_len = *subframe_len + sizeof(struct ethhdr);
-	int padding = (4 - amsdu_len) & 3;
-
-	if (skb_headroom(skb) < headroom || skb_tailroom(skb) < padding) {
+	if (skb_headroom(skb) < headroom) {
 		I802_DEBUG_INC(local->tx_expand_skb_head);
 
-		if (pskb_expand_head(skb, headroom, padding, GFP_ATOMIC)) {
+		if (pskb_expand_head(skb, headroom, 0, GFP_ATOMIC)) {
 			wiphy_debug(local->hw.wiphy,
 				    "failed to reallocate TX buffer\n");
 			return false;
 		}
 	}
 
-	if (padding) {
-		*subframe_len += padding;
-		skb_put_zero(skb, padding);
-	}
-
 	return true;
 }
 
@@ -3117,8 +3108,7 @@ static bool ieee80211_amsdu_prepare_head(struct ieee80211_sub_if_data *sdata,
 	if (info->control.flags & IEEE80211_TX_CTRL_AMSDU)
 		return true;
 
-	if (!ieee80211_amsdu_realloc_pad(local, skb, sizeof(*amsdu_hdr),
-					 &subframe_len))
+	if (!ieee80211_amsdu_realloc_pad(local, skb, sizeof(*amsdu_hdr)))
 		return false;
 
 	data = skb_push(skb, sizeof(*amsdu_hdr));
@@ -3184,7 +3174,8 @@ static bool ieee80211_amsdu_aggregate(struct ieee80211_sub_if_data *sdata,
 	void *data;
 	bool ret = false;
 	unsigned int orig_len;
-	int n = 1, nfrags;
+	int n = 1, nfrags, pad = 0;
+	u16 hdrlen;
 
 	if (!ieee80211_hw_check(&local->hw, TX_AMSDU))
 		return false;
@@ -3235,8 +3226,19 @@ static bool ieee80211_amsdu_aggregate(struct ieee80211_sub_if_data *sdata,
 	if (max_frags && nfrags > max_frags)
 		goto out;
 
-	if (!ieee80211_amsdu_realloc_pad(local, skb, sizeof(rfc1042_header) + 2,
-					 &subframe_len))
+	/*
+	 * Pad out the previous subframe to a multiple of 4 by adding the
+	 * padding to the next one, that's being added. Note that head->len
+	 * is the length of the full A-MSDU, but that works since each time
+	 * we add a new subframe we pad out the previous one to a multiple
+	 * of 4 and thus it no longer matters in the next round.
+	 */
+	hdrlen = fast_tx->hdr_len - sizeof(rfc1042_header);
+	if ((head->len - hdrlen) & 3)
+		pad = 4 - ((head->len - hdrlen) & 3);
+
+	if (!ieee80211_amsdu_realloc_pad(local, skb, sizeof(rfc1042_header) +
+						     2 + pad))
 		goto out;
 
 	ret = true;
@@ -3248,6 +3250,8 @@ static bool ieee80211_amsdu_aggregate(struct ieee80211_sub_if_data *sdata,
 	memcpy(data, &len, 2);
 	memcpy(data + 2, rfc1042_header, sizeof(rfc1042_header));
 
+	memset(skb_push(skb, pad), 0, pad);
+
 	head->len += skb->len;
 	head->data_len += skb->len;
 	*frag_tail = skb;
Signature · 1 line
2.17.1
#23 lore raw

PATCH 24/76 gpiolib: acpi: Switch to cansleep version of GPIO library call

In reply to Sasha Levin

From: Andy Shevchenko <[email protected]>

[ Upstream commit 993b9bc5c47fda86f8ab4e53d68c6fea5ff2764a ]

The commit ca876c7483b6

("gpiolib-acpi: make sure we trigger edge events at least once on boot")

added a initial value check for pin which is about to be locked as IRQ. Unfortunately, not all GPIO drivers can do that atomically. Thus, switch to cansleep version of the call. Otherwise we have a warning:

...

  WARNING: CPU: 2 PID: 1408 at drivers/gpio/gpiolib.c:2883 gpiod_get_value+0x46/0x50
...
  RIP: 0010:gpiod_get_value+0x46/0x50

...

The change tested on Intel Broxton with Whiskey Cove PMIC GPIO controller.

Fixes ca876c7483b6 ("gpiolib-acpi: make sure we trigger edge events at least once on boot")
Cc Hans de Goede <[email protected]>
Cc Benjamin Tissoires <[email protected]>
---
 drivers/gpio/gpiolib-acpi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpio/gpiolib-acpi.c +1 -1
index addd9fecc198..7da51b5186c0 100644
@@ -186,7 +186,7 @@ static acpi_status acpi_gpiochip_request_interrupt(struct acpi_resource *ares,
 
 	gpiod_direction_input(desc);
 
-	value = gpiod_get_value(desc);
+	value = gpiod_get_value_cansleep(desc);
 
 	ret = gpiochip_lock_as_irq(chip, pin);
 	if (ret) {
Signature · 1 line
2.17.1
#24 lore raw

PATCH 25/76 gpiolib-acpi: Register GpioInt ACPI event handlers from a late_initcall

In reply to Sasha Levin

From: Hans de Goede <[email protected]>

[ Upstream commit 78d3a92edbfb02e8cb83173cad84c3f2d5e1f070 ]

GpioInt ACPI event handlers may see there IRQ triggered immediately after requesting the IRQ (esp. level triggered ones). This means that they may run before any other (builtin) drivers have had a chance to register their OpRegion handlers, leading to errors like this:

[    1.133274] ACPI Error: No handler for Region [PMOP] ((____ptrval____)) [UserDefinedRegion] (20180531/evregion-132)
[    1.133286] ACPI Error: Region UserDefinedRegion (ID=141) has no handler (20180531/exfldio-265)
[    1.133297] ACPI Error: Method parse/execution failed \_SB.GPO2._L01, AE_NOT_EXIST (20180531/psparse-516)

We already defer the manual initial trigger of edge triggered interrupts by running it from a late_initcall handler, this commit replaces this with deferring the entire acpi_gpiochip_request_interrupts() call till then, fixing the problem of some OpRegions not being registered yet.

Note that this removes the need to have a list of edge triggered handlers which need to run, since the entire acpi_gpiochip_request_interrupts() call is now delayed, acpi_gpiochip_request_interrupt() can call these directly now.

---
 drivers/gpio/gpiolib-acpi.c | 84 +++++++++++++++++++++----------------
 1 file changed, 49 insertions(+), 35 deletions(-)
drivers/gpio/gpiolib-acpi.c +49 -35
index 7da51b5186c0..a3e43cacd78e 100644
@@ -25,7 +25,6 @@
 
 struct acpi_gpio_event {
 	struct list_head node;
-	struct list_head initial_sync_list;
 	acpi_handle handle;
 	unsigned int pin;
 	unsigned int irq;
@@ -49,10 +48,19 @@ struct acpi_gpio_chip {
 	struct mutex conn_lock;
 	struct gpio_chip *chip;
 	struct list_head events;
+	struct list_head deferred_req_irqs_list_entry;
 };
 
-static LIST_HEAD(acpi_gpio_initial_sync_list);
-static DEFINE_MUTEX(acpi_gpio_initial_sync_list_lock);
+/*
+ * For gpiochips which call acpi_gpiochip_request_interrupts() before late_init
+ * (so builtin drivers) we register the ACPI GpioInt event handlers from a
+ * late_initcall_sync handler, so that other builtin drivers can register their
+ * OpRegions before the event handlers can run.  This list contains gpiochips
+ * for which the acpi_gpiochip_request_interrupts() has been deferred.
+ */
+static DEFINE_MUTEX(acpi_gpio_deferred_req_irqs_lock);
+static LIST_HEAD(acpi_gpio_deferred_req_irqs_list);
+static bool acpi_gpio_deferred_req_irqs_done;
 
 static int acpi_gpiochip_find(struct gpio_chip *gc, void *data)
 {
@@ -89,21 +97,6 @@ static struct gpio_desc *acpi_get_gpiod(char *path, int pin)
 	return gpiochip_get_desc(chip, pin);
 }
 
-static void acpi_gpio_add_to_initial_sync_list(struct acpi_gpio_event *event)
-{
-	mutex_lock(&acpi_gpio_initial_sync_list_lock);
-	list_add(&event->initial_sync_list, &acpi_gpio_initial_sync_list);
-	mutex_unlock(&acpi_gpio_initial_sync_list_lock);
-}
-
-static void acpi_gpio_del_from_initial_sync_list(struct acpi_gpio_event *event)
-{
-	mutex_lock(&acpi_gpio_initial_sync_list_lock);
-	if (!list_empty(&event->initial_sync_list))
-		list_del_init(&event->initial_sync_list);
-	mutex_unlock(&acpi_gpio_initial_sync_list_lock);
-}
-
 static irqreturn_t acpi_gpio_irq_handler(int irq, void *data)
 {
 	struct acpi_gpio_event *event = data;
@@ -229,7 +222,6 @@ static acpi_status acpi_gpiochip_request_interrupt(struct acpi_resource *ares,
 	event->irq = irq;
 	event->pin = pin;
 	event->desc = desc;
-	INIT_LIST_HEAD(&event->initial_sync_list);
 
 	ret = request_threaded_irq(event->irq, NULL, handler, irqflags,
 				   "ACPI:Event", event);
@@ -251,10 +243,9 @@ static acpi_status acpi_gpiochip_request_interrupt(struct acpi_resource *ares,
 	 * may refer to OperationRegions from other (builtin) drivers which
 	 * may be probed after us.
 	 */
-	if (handler == acpi_gpio_irq_handler &&
-	    (((irqflags & IRQF_TRIGGER_RISING) && value == 1) ||
-	     ((irqflags & IRQF_TRIGGER_FALLING) && value == 0)))
-		acpi_gpio_add_to_initial_sync_list(event);
+	if (((irqflags & IRQF_TRIGGER_RISING) && value == 1) ||
+	    ((irqflags & IRQF_TRIGGER_FALLING) && value == 0))
+		handler(event->irq, event);
 
 	return AE_OK;
 
@@ -283,6 +274,7 @@ void acpi_gpiochip_request_interrupts(struct gpio_chip *chip)
 	struct acpi_gpio_chip *acpi_gpio;
 	acpi_handle handle;
 	acpi_status status;
+	bool defer;
 
 	if (!chip->parent || !chip->to_irq)
 		return;
@@ -295,6 +287,16 @@ void acpi_gpiochip_request_interrupts(struct gpio_chip *chip)
 	if (ACPI_FAILURE(status))
 		return;
 
+	mutex_lock(&acpi_gpio_deferred_req_irqs_lock);
+	defer = !acpi_gpio_deferred_req_irqs_done;
+	if (defer)
+		list_add(&acpi_gpio->deferred_req_irqs_list_entry,
+			 &acpi_gpio_deferred_req_irqs_list);
+	mutex_unlock(&acpi_gpio_deferred_req_irqs_lock);
+
+	if (defer)
+		return;
+
 	acpi_walk_resources(handle, "_AEI",
 			    acpi_gpiochip_request_interrupt, acpi_gpio);
 }
@@ -325,11 +327,14 @@ void acpi_gpiochip_free_interrupts(struct gpio_chip *chip)
 	if (ACPI_FAILURE(status))
 		return;
 
+	mutex_lock(&acpi_gpio_deferred_req_irqs_lock);
+	if (!list_empty(&acpi_gpio->deferred_req_irqs_list_entry))
+		list_del_init(&acpi_gpio->deferred_req_irqs_list_entry);
+	mutex_unlock(&acpi_gpio_deferred_req_irqs_lock);
+
 	list_for_each_entry_safe_reverse(event, ep, &acpi_gpio->events, node) {
 		struct gpio_desc *desc;
 
-		acpi_gpio_del_from_initial_sync_list(event);
-
 		if (irqd_is_wakeup_set(irq_get_irq_data(event->irq)))
 			disable_irq_wake(event->irq);
 
@@ -1049,6 +1054,7 @@ void acpi_gpiochip_add(struct gpio_chip *chip)
 
 	acpi_gpio->chip = chip;
 	INIT_LIST_HEAD(&acpi_gpio->events);
+	INIT_LIST_HEAD(&acpi_gpio->deferred_req_irqs_list_entry);
 
 	status = acpi_attach_data(handle, acpi_gpio_chip_dh, acpi_gpio);
 	if (ACPI_FAILURE(status)) {
@@ -1195,20 +1201,28 @@ bool acpi_can_fallback_to_crs(struct acpi_device *adev, const char *con_id)
 	return con_id == NULL;
 }
 
-/* Sync the initial state of handlers after all builtin drivers have probed */
-static int acpi_gpio_initial_sync(void)
+/* Run deferred acpi_gpiochip_request_interrupts() */
+static int acpi_gpio_handle_deferred_request_interrupts(void)
 {
-	struct acpi_gpio_event *event, *ep;
+	struct acpi_gpio_chip *acpi_gpio, *tmp;
+
+	mutex_lock(&acpi_gpio_deferred_req_irqs_lock);
+	list_for_each_entry_safe(acpi_gpio, tmp,
+				 &acpi_gpio_deferred_req_irqs_list,
+				 deferred_req_irqs_list_entry) {
+		acpi_handle handle;
 
-	mutex_lock(&acpi_gpio_initial_sync_list_lock);
-	list_for_each_entry_safe(event, ep, &acpi_gpio_initial_sync_list,
-				 initial_sync_list) {
-		acpi_evaluate_object(event->handle, NULL, NULL, NULL);
-		list_del_init(&event->initial_sync_list);
+		handle = ACPI_HANDLE(acpi_gpio->chip->parent);
+		acpi_walk_resources(handle, "_AEI",
+				    acpi_gpiochip_request_interrupt, acpi_gpio);
+
+		list_del_init(&acpi_gpio->deferred_req_irqs_list_entry);
 	}
-	mutex_unlock(&acpi_gpio_initial_sync_list_lock);
+
+	acpi_gpio_deferred_req_irqs_done = true;
+	mutex_unlock(&acpi_gpio_deferred_req_irqs_lock);
 
 	return 0;
 }
 /* We must use _sync so that this runs after the first deferred_probe run */
-late_initcall_sync(acpi_gpio_initial_sync);
+late_initcall_sync(acpi_gpio_handle_deferred_request_interrupts);
Signature · 1 line
2.17.1
#25 lore raw

PATCH 26/76 gpio: dwapb: Fix error handling in dwapb_gpio_probe()

In reply to Sasha Levin

From: Alexey Khoroshilov <[email protected]>

[ Upstream commit a618cf4800970d260871c159b7eec014a1da2e81 ]

If dwapb_gpio_add_port() fails in dwapb_gpio_probe(), gpio->clk is left undisabled.

Found by Linux Driver Verification project (linuxtesting.org).

---
 drivers/gpio/gpio-dwapb.c | 1 +
 1 file changed, 1 insertion(+)
drivers/gpio/gpio-dwapb.c +1 -0
index 7a2de3de6571..5b12d6fdd448 100644
@@ -726,6 +726,7 @@ static int dwapb_gpio_probe(struct platform_device *pdev)
 out_unregister:
 	dwapb_gpio_unregister(gpio);
 	dwapb_irq_teardown(gpio);
+	clk_disable_unprepare(gpio->clk);
 
 	return err;
 }
Signature · 1 line
2.17.1
#26 lore raw

PATCH 27/76 bpf: fix msg->data/data_end after sg shift repair in bpf_msg_pull_data

In reply to Sasha Levin

From: Daniel Borkmann <[email protected]>

[ Upstream commit 0e06b227c5221dd51b5569de93f3b9f532be4a32 ]

In the current code, msg->data is set as sg_virt(&sg[i]) + start - offset and msg->data_end relative to it as msg->data + bytes. Using iterator i to point to the updated starting scatterlist element holds true for some cases, however not for all where we'd end up pointing out of bounds. It is /correct/ for these ones:

1) When first finding the starting scatterlist element (sge) where we find that the page is already privately owned by the msg and where the requested bytes and headroom fit into the sge's length.

However, it's /incorrect/ for the following ones:

2) After we made the requested area private and updated the newly allocated page into first_sg slot of the scatterlist ring; when we find that no shift repair of the ring is needed where we bail out updating msg->data and msg->data_end. At that point i will point to last_sg, which in this case is the next elem of first_sg in the ring. The sge at that point might as well be invalid (e.g. i == msg->sg_end), which we use for setting the range of sg_virt(&sg[i]). The correct one would have been first_sg.

3) Similar as in 2) but when we find that a shift repair of the ring is needed. In this case we fix up all sges and stop once we've reached the end. In this case i will point to will point to the new msg->sg_end, and the sge at that point will be invalid. Again here the requested range sits in first_sg.

Fixes 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
---
 net/core/filter.c | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)
net/core/filter.c +2 -3
index a9f8d71575c7..e713a8791815 100644
@@ -2300,6 +2300,7 @@ BPF_CALL_4(bpf_msg_pull_data,
 	if (unlikely(start >= offset + len))
 		return -EINVAL;
 
+	first_sg = i;
 	/* The start may point into the sg element so we need to also
 	 * account for the headroom.
 	 */
@@ -2307,8 +2308,6 @@ BPF_CALL_4(bpf_msg_pull_data,
 	if (!msg->sg_copy[i] && bytes_sg_total <= len)
 		goto out;
 
-	first_sg = i;
-
 	/* At this point we need to linearize multiple scatterlist
 	 * elements or a single shared page. Either way we need to
 	 * copy into a linear buffer exclusively owned by BPF. Then
@@ -2390,7 +2389,7 @@ BPF_CALL_4(bpf_msg_pull_data,
 	if (msg->sg_end < 0)
 		msg->sg_end += MAX_SKB_FRAGS;
 out:
-	msg->data = sg_virt(&sg[i]) + start - offset;
+	msg->data = sg_virt(&sg[first_sg]) + start - offset;
 	msg->data_end = msg->data + bytes;
 
 	return 0;
Signature · 1 line
2.17.1
#27 lore raw

PATCH 28/76 bpf: fix shift upon scatterlist ring wrap-around in bpf_msg_pull_data

In reply to Sasha Levin

From: Daniel Borkmann <[email protected]>

[ Upstream commit 2e43f95dd8ee62bc8bf57f2afac37fbd70c8d565 ]

If first_sg and last_sg wraps around in the scatterlist ring, then we need to account for that in the shift as well. E.g. crafting such msgs where this is the case leads to a hang as shift becomes negative. E.g. consider the following scenario:

  first_sg := 14     |=>    shift := -12     msg->sg_start := 10
  last_sg  :=  3     |                       msg->sg_end   :=  5
round  1:  i := 15, move_from :=   3, sg[15] := sg[  3]
round  2:  i :=  0, move_from := -12, sg[ 0] := sg[-12]
round  3:  i :=  1, move_from := -11, sg[ 1] := sg[-11]
round  4:  i :=  2, move_from := -10, sg[ 2] := sg[-10]
[...]
round 13:  i := 11, move_from :=  -1, sg[ 2] := sg[ -1]
round 14:  i := 12, move_from :=   0, sg[ 2] := sg[  0]
round 15:  i := 13, move_from :=   1, sg[ 2] := sg[  1]
round 16:  i := 14, move_from :=   2, sg[ 2] := sg[  2]
round 17:  i := 15, move_from :=   3, sg[ 2] := sg[  3]

[...]

This means we will loop forever and never hit the msg->sg_end condition to break out of the loop. When we see that the ring wraps around, then the shift should be MAX_SKB_FRAGS - first_sg + last_sg - 1. Meaning, the remainder slots from the tail of the ring and the head until last_sg combined.

Fixes 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
---
 net/core/filter.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
net/core/filter.c +4 -1
index e713a8791815..cc4d660aafe1 100644
@@ -2360,7 +2360,10 @@ BPF_CALL_4(bpf_msg_pull_data,
 	 * had a single entry though we can just replace it and
 	 * be done. Otherwise walk the ring and shift the entries.
 	 */
-	shift = last_sg - first_sg - 1;
+	WARN_ON_ONCE(last_sg == first_sg);
+	shift = last_sg > first_sg ?
+		last_sg - first_sg - 1 :
+		MAX_SKB_FRAGS - first_sg + last_sg - 1;
 	if (!shift)
 		goto out;
 
Signature · 1 line
2.17.1
#28 lore raw

PATCH 29/76 bpf: fix sg shift repair start offset in bpf_msg_pull_data

In reply to Sasha Levin

From: Daniel Borkmann <[email protected]>

[ Upstream commit a8cf76a9023bc6709b1361d06bb2fae5227b9d68 ]

When we perform the sg shift repair for the scatterlist ring, we currently start out at i = first_sg + 1. However, this is not correct since the first_sg could point to the sge sitting at slot MAX_SKB_FRAGS - 1, and a subsequent i = MAX_SKB_FRAGS will access the scatterlist ring (sg) out of bounds. Add the sk_msg_iter_var() helper for iterating through the ring, and apply the same rule for advancing to the next ring element as we do elsewhere. Later work will use this helper also in other places.

Fixes 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
---
 net/core/filter.c | 26 +++++++++++++-------------
 1 file changed, 13 insertions(+), 13 deletions(-)
net/core/filter.c +13 -13
index cc4d660aafe1..a80b57e4aaed 100644
@@ -2272,6 +2272,13 @@ static const struct bpf_func_proto bpf_msg_cork_bytes_proto = {
 	.arg2_type      = ARG_ANYTHING,
 };
 
+#define sk_msg_iter_var(var)			\
+	do {					\
+		var++;				\
+		if (var == MAX_SKB_FRAGS)	\
+			var = 0;		\
+	} while (0)
+
 BPF_CALL_4(bpf_msg_pull_data,
 	   struct sk_msg_buff *, msg, u32, start, u32, end, u64, flags)
 {
@@ -2292,9 +2299,7 @@ BPF_CALL_4(bpf_msg_pull_data,
 		if (start < offset + len)
 			break;
 		offset += len;
-		i++;
-		if (i == MAX_SKB_FRAGS)
-			i = 0;
+		sk_msg_iter_var(i);
 	} while (i != msg->sg_end);
 
 	if (unlikely(start >= offset + len))
@@ -2320,9 +2325,7 @@ BPF_CALL_4(bpf_msg_pull_data,
 	 */
 	do {
 		copy += sg[i].length;
-		i++;
-		if (i == MAX_SKB_FRAGS)
-			i = 0;
+		sk_msg_iter_var(i);
 		if (bytes_sg_total <= copy)
 			break;
 	} while (i != msg->sg_end);
@@ -2348,9 +2351,7 @@ BPF_CALL_4(bpf_msg_pull_data,
 		sg[i].length = 0;
 		put_page(sg_page(&sg[i]));
 
-		i++;
-		if (i == MAX_SKB_FRAGS)
-			i = 0;
+		sk_msg_iter_var(i);
 	} while (i != last_sg);
 
 	sg[first_sg].length = copy;
@@ -2367,7 +2368,8 @@ BPF_CALL_4(bpf_msg_pull_data,
 	if (!shift)
 		goto out;
 
-	i = first_sg + 1;
+	i = first_sg;
+	sk_msg_iter_var(i);
 	do {
 		int move_from;
 
@@ -2384,9 +2386,7 @@ BPF_CALL_4(bpf_msg_pull_data,
 		sg[move_from].page_link = 0;
 		sg[move_from].offset = 0;
 
-		i++;
-		if (i == MAX_SKB_FRAGS)
-			i = 0;
+		sk_msg_iter_var(i);
 	} while (1);
 	msg->sg_end -= shift;
 	if (msg->sg_end < 0)
Signature · 1 line
2.17.1
#29 lore raw

PATCH 31/76 net: hns: add the code for cleaning pkt in chip

In reply to Sasha Levin

From: Peng Li <[email protected]>

[ Upstream commit 31fabbee8f5c658c3fa1603c66e9e4f51ea8c2c6 ]

If there are packets in hardware when changing the speed or duplex, it may cause hardware hang up.

This patch adds the code for waiting chip to clean the all pkts(TX & RX) in chip when the driver uses the function named "adjust link".

This patch cleans the pkts as follows:
1) close rx of chip, close tx of protocol stack.
2) wait rcb, ppe, mac to clean.
3) adjust link
4) open rx of chip, open tx of protocol stack.

---
 drivers/net/ethernet/hisilicon/hns/hnae.h     |  2 +
 .../net/ethernet/hisilicon/hns/hns_ae_adapt.c | 67 ++++++++++++++++++-
 .../ethernet/hisilicon/hns/hns_dsaf_gmac.c    | 36 ++++++++++
 .../net/ethernet/hisilicon/hns/hns_dsaf_mac.c | 44 ++++++++++++
 .../net/ethernet/hisilicon/hns/hns_dsaf_mac.h |  8 +++
 .../ethernet/hisilicon/hns/hns_dsaf_main.c    | 29 ++++++++
 .../ethernet/hisilicon/hns/hns_dsaf_main.h    |  3 +
 .../net/ethernet/hisilicon/hns/hns_dsaf_ppe.c | 23 +++++++
 .../net/ethernet/hisilicon/hns/hns_dsaf_ppe.h |  1 +
 .../net/ethernet/hisilicon/hns/hns_dsaf_rcb.c | 23 +++++++
 .../net/ethernet/hisilicon/hns/hns_dsaf_rcb.h |  1 +
 .../net/ethernet/hisilicon/hns/hns_dsaf_reg.h |  1 +
 drivers/net/ethernet/hisilicon/hns/hns_enet.c | 21 +++++-
 13 files changed, 255 insertions(+), 4 deletions(-)
drivers/net/ethernet/hisilicon/hns/hnae.h +2 -0
index fa5b30f547f6..427866b9564e 100644
@@ -486,6 +486,8 @@ struct hnae_ae_ops {
 			u8 *auto_neg, u16 *speed, u8 *duplex);
 	void (*toggle_ring_irq)(struct hnae_ring *ring, u32 val);
 	void (*adjust_link)(struct hnae_handle *handle, int speed, int duplex);
+	bool (*need_adjust_link)(struct hnae_handle *handle,
+				 int speed, int duplex);
 	int (*set_loopback)(struct hnae_handle *handle,
 			    enum hnae_loop loop_mode, int en);
 	void (*get_ring_bdnum_limit)(struct hnae_queue *queue,
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c +66 -1

90 lines not on this page · raw message

drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c +36 -0
index 74bd260ca02a..8c7bc5cf193c 100644
@@ -257,6 +257,16 @@ static void hns_gmac_get_pausefrm_cfg(void *mac_drv, u32 *rx_pause_en,
 	*tx_pause_en = dsaf_get_bit(pause_en, GMAC_PAUSE_EN_TX_FDFC_B);
 }
 
+static bool hns_gmac_need_adjust_link(void *mac_drv, enum mac_speed speed,
+				      int duplex)
+{
+	struct mac_driver *drv = (struct mac_driver *)mac_drv;
+	struct hns_mac_cb *mac_cb = drv->mac_cb;
+
+	return (mac_cb->speed != speed) ||
+		(mac_cb->half_duplex == duplex);
+}
+
 static int hns_gmac_adjust_link(void *mac_drv, enum mac_speed speed,
 				u32 full_duplex)
 {
@@ -309,6 +319,30 @@ static void hns_gmac_set_promisc(void *mac_drv, u8 en)
 		hns_gmac_set_uc_match(mac_drv, en);
 }
 
+int hns_gmac_wait_fifo_clean(void *mac_drv)
+{
+	struct mac_driver *drv = (struct mac_driver *)mac_drv;
+	int wait_cnt;
+	u32 val;
+
+	wait_cnt = 0;
+	while (wait_cnt++ < HNS_MAX_WAIT_CNT) {
+		val = dsaf_read_dev(drv, GMAC_FIFO_STATE_REG);
+		/* bit5~bit0 is not send complete pkts */
+		if ((val & 0x3f) == 0)
+			break;
+		usleep_range(100, 200);
+	}
+
+	if (wait_cnt >= HNS_MAX_WAIT_CNT) {
+		dev_err(drv->dev,
+			"hns ge %d fifo was not idle.\n", drv->mac_id);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
 static void hns_gmac_init(void *mac_drv)
 {
 	u32 port;
@@ -690,6 +724,7 @@ void *hns_gmac_config(struct hns_mac_cb *mac_cb, struct mac_params *mac_param)
 	mac_drv->mac_disable = hns_gmac_disable;
 	mac_drv->mac_free = hns_gmac_free;
 	mac_drv->adjust_link = hns_gmac_adjust_link;
+	mac_drv->need_adjust_link = hns_gmac_need_adjust_link;
 	mac_drv->set_tx_auto_pause_frames = hns_gmac_set_tx_auto_pause_frames;
 	mac_drv->config_max_frame_length = hns_gmac_config_max_frame_length;
 	mac_drv->mac_pausefrm_cfg = hns_gmac_pause_frm_cfg;
@@ -717,6 +752,7 @@ void *hns_gmac_config(struct hns_mac_cb *mac_cb, struct mac_params *mac_param)
 	mac_drv->get_strings = hns_gmac_get_strings;
 	mac_drv->update_stats = hns_gmac_update_stats;
 	mac_drv->set_promiscuous = hns_gmac_set_promisc;
+	mac_drv->wait_fifo_clean = hns_gmac_wait_fifo_clean;
 
 	return (void *)mac_drv;
 }
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c +44 -0

62 lines not on this page · raw message

drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.h +8 -0
index bbc0a98e7ca3..fbc75341bef7 100644
@@ -356,6 +356,9 @@ struct mac_driver {
 	/*adjust mac mode of port,include speed and duplex*/
 	int (*adjust_link)(void *mac_drv, enum mac_speed speed,
 			   u32 full_duplex);
+	/* need adjust link */
+	bool (*need_adjust_link)(void *mac_drv, enum mac_speed speed,
+				 int duplex);
 	/* config autoegotaite mode of port*/
 	void (*set_an_mode)(void *mac_drv, u8 enable);
 	/* config loopbank mode */
@@ -394,6 +397,7 @@ struct mac_driver {
 	void (*get_info)(void *mac_drv, struct mac_info *mac_info);
 
 	void (*update_stats)(void *mac_drv);
+	int (*wait_fifo_clean)(void *mac_drv);
 
 	enum mac_mode mac_mode;
 	u8 mac_id;
@@ -427,6 +431,7 @@ void *hns_xgmac_config(struct hns_mac_cb *mac_cb,
 
 int hns_mac_init(struct dsaf_device *dsaf_dev);
 void mac_adjust_link(struct net_device *net_dev);
+bool hns_mac_need_adjust_link(struct hns_mac_cb *mac_cb, int speed, int duplex);
 void hns_mac_get_link_status(struct hns_mac_cb *mac_cb,	u32 *link_status);
 int hns_mac_change_vf_addr(struct hns_mac_cb *mac_cb, u32 vmid, char *addr);
 int hns_mac_set_multi(struct hns_mac_cb *mac_cb,
@@ -463,5 +468,8 @@ int hns_mac_add_uc_addr(struct hns_mac_cb *mac_cb, u8 vf_id,
 int hns_mac_rm_uc_addr(struct hns_mac_cb *mac_cb, u8 vf_id,
 		       const unsigned char *addr);
 int hns_mac_clr_multicast(struct hns_mac_cb *mac_cb, int vfn);
+void hns_mac_enable(struct hns_mac_cb *mac_cb, enum mac_commom_mode mode);
+void hns_mac_disable(struct hns_mac_cb *mac_cb, enum mac_commom_mode mode);
+int hns_mac_wait_fifo_clean(struct hns_mac_cb *mac_cb);
 
 #endif /* _HNS_DSAF_MAC_H */
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c +29 -0
index 0ce07f6eb1e6..0ef6d429308f 100644
@@ -2733,6 +2733,35 @@ void hns_dsaf_set_promisc_tcam(struct dsaf_device *dsaf_dev,
 	soft_mac_entry->index = enable ? entry_index : DSAF_INVALID_ENTRY_IDX;
 }
 
+int hns_dsaf_wait_pkt_clean(struct dsaf_device *dsaf_dev, int port)
+{
+	u32 val, val_tmp;
+	int wait_cnt;
+
+	if (port >= DSAF_SERVICE_NW_NUM)
+		return 0;
+
+	wait_cnt = 0;
+	while (wait_cnt++ < HNS_MAX_WAIT_CNT) {
+		val = dsaf_read_dev(dsaf_dev, DSAF_VOQ_IN_PKT_NUM_0_REG +
+			(port + DSAF_XGE_NUM) * 0x40);
+		val_tmp = dsaf_read_dev(dsaf_dev, DSAF_VOQ_OUT_PKT_NUM_0_REG +
+			(port + DSAF_XGE_NUM) * 0x40);
+		if (val == val_tmp)
+			break;
+
+		usleep_range(100, 200);
+	}
+
+	if (wait_cnt >= HNS_MAX_WAIT_CNT) {
+		dev_err(dsaf_dev->dev, "hns dsaf clean wait timeout(%u - %u).\n",
+			val, val_tmp);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
 /**
  * dsaf_probe - probo dsaf dev
  * @pdev: dasf platform device
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.h +3 -0
index 4507e8222683..0e1cd99831a6 100644
@@ -44,6 +44,8 @@ struct hns_mac_cb;
 #define DSAF_ROCE_CREDIT_CHN	8
 #define DSAF_ROCE_CHAN_MODE	3
 
+#define HNS_MAX_WAIT_CNT 10000
+
 enum dsaf_roce_port_mode {
 	DSAF_ROCE_6PORT_MODE,
 	DSAF_ROCE_4PORT_MODE,
@@ -463,5 +465,6 @@ int hns_dsaf_rm_mac_addr(
 
 int hns_dsaf_clr_mac_mc_port(struct dsaf_device *dsaf_dev,
 			     u8 mac_id, u8 port_num);
+int hns_dsaf_wait_pkt_clean(struct dsaf_device *dsaf_dev, int port);
 
 #endif /* __HNS_DSAF_MAIN_H__ */
drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c +23 -0
index 93e71e27401b..a19932aeb9d7 100644
@@ -274,6 +274,29 @@ static void hns_ppe_exc_irq_en(struct hns_ppe_cb *ppe_cb, int en)
 	dsaf_write_dev(ppe_cb, PPE_INTEN_REG, msk_vlue & vld_msk);
 }
 
+int hns_ppe_wait_tx_fifo_clean(struct hns_ppe_cb *ppe_cb)
+{
+	int wait_cnt;
+	u32 val;
+
+	wait_cnt = 0;
+	while (wait_cnt++ < HNS_MAX_WAIT_CNT) {
+		val = dsaf_read_dev(ppe_cb, PPE_CURR_TX_FIFO0_REG) & 0x3ffU;
+		if (!val)
+			break;
+
+		usleep_range(100, 200);
+	}
+
+	if (wait_cnt >= HNS_MAX_WAIT_CNT) {
+		dev_err(ppe_cb->dev, "hns ppe tx fifo clean wait timeout, still has %u pkt.\n",
+			val);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
 /**
  * ppe_init_hw - init ppe
  * @ppe_cb: ppe device
drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.h +1 -0
index 9d8e643e8aa6..f670e63a5a01 100644
@@ -100,6 +100,7 @@ struct ppe_common_cb {
 
 };
 
+int hns_ppe_wait_tx_fifo_clean(struct hns_ppe_cb *ppe_cb);
 int hns_ppe_init(struct dsaf_device *dsaf_dev);
 
 void hns_ppe_uninit(struct dsaf_device *dsaf_dev);
drivers/net/ethernet/hisilicon/hns/hns_dsaf_rcb.c +23 -0
index e2e28532e4dc..1e43d7a3ca86 100644
@@ -66,6 +66,29 @@ void hns_rcb_wait_fbd_clean(struct hnae_queue **qs, int q_num, u32 flag)
 			"queue(%d) wait fbd(%d) clean fail!!\n", i, fbd_num);
 }
 
+int hns_rcb_wait_tx_ring_clean(struct hnae_queue *qs)
+{
+	u32 head, tail;
+	int wait_cnt;
+
+	tail = dsaf_read_dev(&qs->tx_ring, RCB_REG_TAIL);
+	wait_cnt = 0;
+	while (wait_cnt++ < HNS_MAX_WAIT_CNT) {
+		head = dsaf_read_dev(&qs->tx_ring, RCB_REG_HEAD);
+		if (tail == head)
+			break;
+
+		usleep_range(100, 200);
+	}
+
+	if (wait_cnt >= HNS_MAX_WAIT_CNT) {
+		dev_err(qs->dev->dev, "rcb wait timeout, head not equal to tail.\n");
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
 /**
  *hns_rcb_reset_ring_hw - ring reset
  *@q: ring struct pointer
drivers/net/ethernet/hisilicon/hns/hns_dsaf_rcb.h +1 -0
index 602816498c8d..2319b772a271 100644
@@ -136,6 +136,7 @@ void hns_rcbv2_int_clr_hw(struct hnae_queue *q, u32 flag);
 void hns_rcb_init_hw(struct ring_pair_cb *ring);
 void hns_rcb_reset_ring_hw(struct hnae_queue *q);
 void hns_rcb_wait_fbd_clean(struct hnae_queue **qs, int q_num, u32 flag);
+int hns_rcb_wait_tx_ring_clean(struct hnae_queue *qs);
 u32 hns_rcb_get_rx_coalesced_frames(
 	struct rcb_common_cb *rcb_common, u32 port_idx);
 u32 hns_rcb_get_tx_coalesced_frames(
drivers/net/ethernet/hisilicon/hns/hns_dsaf_reg.h +1 -0
index 886cbbf25761..74d935d82cbc 100644
@@ -464,6 +464,7 @@
 #define RCB_RING_INTMSK_TX_OVERTIME_REG		0x000C4
 #define RCB_RING_INTSTS_TX_OVERTIME_REG		0x000C8
 
+#define GMAC_FIFO_STATE_REG			0x0000UL
 #define GMAC_DUPLEX_TYPE_REG			0x0008UL
 #define GMAC_FD_FC_TYPE_REG			0x000CUL
 #define GMAC_TX_WATER_LINE_REG			0x0010UL
drivers/net/ethernet/hisilicon/hns/hns_enet.c +18 -3
index ef9ef703d13a..48397d4e180f 100644
@@ -1212,11 +1212,26 @@ static void hns_nic_adjust_link(struct net_device *ndev)
 	struct hnae_handle *h = priv->ae_handle;
 	int state = 1;
 
+	/* If there is no phy, do not need adjust link */
 	if (ndev->phydev) {
-		h->dev->ops->adjust_link(h, ndev->phydev->speed,
-					 ndev->phydev->duplex);
-		state = ndev->phydev->link;
+		/* When phy link down, do nothing */
+		if (ndev->phydev->link == 0)
+			return;
+
+		if (h->dev->ops->need_adjust_link(h, ndev->phydev->speed,
+						  ndev->phydev->duplex)) {
+			/* because Hi161X chip don't support to change gmac
+			 * speed and duplex with traffic. Delay 200ms to
+			 * make sure there is no more data in chip FIFO.
+			 */
+			netif_carrier_off(ndev);
+			msleep(200);
+			h->dev->ops->adjust_link(h, ndev->phydev->speed,
+						 ndev->phydev->duplex);
+			netif_carrier_on(ndev);
+		}
 	}
+
 	state = state && h->dev->ops->get_status(h);
 
 	if (state != priv->link) {
Signature · 1 line
2.17.1
#30 lore raw

PATCH 32/76 net: hns: add netif_carrier_off before change speed and duplex

In reply to Sasha Levin

From: Peng Li <[email protected]>

[ Upstream commit 455c4401fe7a538facaffb35b906ce19f1ece474 ]

If there are packets in hardware when changing the speed or duplex, it may cause hardware hang up.

This patch adds netif_carrier_off before change speed and duplex in ethtool_ops.set_link_ksettings, and adds netif_carrier_on after complete the change.

---
 drivers/net/ethernet/hisilicon/hns/hns_ethtool.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c +2 -0
index 2e14a3ae1d8b..c1e947bb852f 100644
@@ -243,7 +243,9 @@ static int hns_nic_set_link_ksettings(struct net_device *net_dev,
 	}
 
 	if (h->dev->ops->adjust_link) {
+		netif_carrier_off(net_dev);
 		h->dev->ops->adjust_link(h, (int)speed, cmd->base.duplex);
+		netif_carrier_on(net_dev);
 		return 0;
 	}
 
Signature · 1 line
2.17.1
#31 lore raw

PATCH 33/76 sh_eth: Add R7S9210 support

In reply to Sasha Levin

From: Chris Brandt <[email protected]>

[ Upstream commit 6e0bb04d0e4f597d8d8f4f21401a9636f2809fd1 ]

Add support for the R7S9210 which is part of the RZ/A2 series.

---
 .../devicetree/bindings/net/sh_eth.txt        |  1 +
 drivers/net/ethernet/renesas/sh_eth.c         | 36 +++++++++++++++++++
 2 files changed, 37 insertions(+)
Documentation/devicetree/bindings/net/sh_eth.txt +1 -0
index 82a4cf2c145d..a62fe3b613fc 100644
@@ -16,6 +16,7 @@ Required properties:
 	      "renesas,ether-r8a7794"  if the device is a part of R8A7794 SoC.
 	      "renesas,gether-r8a77980" if the device is a part of R8A77980 SoC.
 	      "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC.
+	      "renesas,ether-r7s9210" if the device is a part of R7S9210 SoC.
 	      "renesas,rcar-gen1-ether" for a generic R-Car Gen1 device.
 	      "renesas,rcar-gen2-ether" for a generic R-Car Gen2 or RZ/G1
 	                                device.
drivers/net/ethernet/renesas/sh_eth.c +36 -0
index 5614fd231bbe..6520379b390e 100644
@@ -807,6 +807,41 @@ static struct sh_eth_cpu_data r8a77980_data = {
 	.magic		= 1,
 	.cexcr		= 1,
 };
+
+/* R7S9210 */
+static struct sh_eth_cpu_data r7s9210_data = {
+	.soft_reset	= sh_eth_soft_reset,
+
+	.set_duplex	= sh_eth_set_duplex,
+	.set_rate	= sh_eth_set_rate_rcar,
+
+	.register_type	= SH_ETH_REG_FAST_SH4,
+
+	.edtrr_trns	= EDTRR_TRNS_ETHER,
+	.ecsr_value	= ECSR_ICD,
+	.ecsipr_value	= ECSIPR_ICDIP,
+	.eesipr_value	= EESIPR_TWBIP | EESIPR_TABTIP | EESIPR_RABTIP |
+			  EESIPR_RFCOFIP | EESIPR_ECIIP | EESIPR_FTCIP |
+			  EESIPR_TDEIP | EESIPR_TFUFIP | EESIPR_FRIP |
+			  EESIPR_RDEIP | EESIPR_RFOFIP | EESIPR_CNDIP |
+			  EESIPR_DLCIP | EESIPR_CDIP | EESIPR_TROIP |
+			  EESIPR_RMAFIP | EESIPR_RRFIP | EESIPR_RTLFIP |
+			  EESIPR_RTSFIP | EESIPR_PREIP | EESIPR_CERFIP,
+
+	.tx_check	= EESR_FTC | EESR_CND | EESR_DLC | EESR_CD | EESR_TRO,
+	.eesr_err_check	= EESR_TWB | EESR_TABT | EESR_RABT | EESR_RFE |
+			  EESR_RDE | EESR_RFRMER | EESR_TFE | EESR_TDE,
+
+	.fdr_value	= 0x0000070f,
+
+	.apr		= 1,
+	.mpr		= 1,
+	.tpauser	= 1,
+	.hw_swap	= 1,
+	.rpadir		= 1,
+	.no_ade		= 1,
+	.xdfar_rw	= 1,
+};
 #endif /* CONFIG_OF */
 
 static void sh_eth_set_rate_sh7724(struct net_device *ndev)
@@ -3131,6 +3166,7 @@ static const struct of_device_id sh_eth_match_table[] = {
 	{ .compatible = "renesas,ether-r8a7794", .data = &rcar_gen2_data },
 	{ .compatible = "renesas,gether-r8a77980", .data = &r8a77980_data },
 	{ .compatible = "renesas,ether-r7s72100", .data = &r7s72100_data },
+	{ .compatible = "renesas,ether-r7s9210", .data = &r7s9210_data },
 	{ .compatible = "renesas,rcar-gen1-ether", .data = &rcar_gen1_data },
 	{ .compatible = "renesas,rcar-gen2-ether", .data = &rcar_gen2_data },
 	{ }
Signature · 1 line
2.17.1
#32 lore raw

PATCH 34/76 net: mvpp2: initialize port of_node pointer

In reply to Sasha Levin

From: Baruch Siach <[email protected]>

[ Upstream commit c4053ef322081554765e1b708d6cdd8855e1d72d ]

Without a valid of_node in struct device we can't find the mvpp2 port device by its DT node. Specifically, this breaks of_find_net_device_by_node().

For example, the Armada 8040 based Clearfog GT-8K uses Marvell 88E6141 switch connected to the &cp1_eth2 port:

&cp1_mdio {
	...

	switch0: switch0@4 {
		compatible = "marvell,mv88e6085";
		...

		ports {
			...

			port@5 {
				reg = <5>;
				label = "cpu";
				ethernet = <&cp1_eth2>;
			};
		};
	};
};

Without this patch, dsa_register_switch() returns -EPROBE_DEFER because of_find_net_device_by_node() can't find the device_node of the &cp1_eth2 device.

---
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c +1 -0
index 0319ed9ef8b8..189fd1fe4ace 100644
@@ -4694,6 +4694,7 @@ static int mvpp2_port_probe(struct platform_device *pdev,
 	dev->min_mtu = ETH_MIN_MTU;
 	/* 9704 == 9728 - 20 and rounding to 8 */
 	dev->max_mtu = MVPP2_BM_JUMBO_PKT_SIZE;
+	dev->dev.of_node = port_node;
 
 	/* Phylink isn't used w/ ACPI as of now */
 	if (port_node) {
Signature · 1 line
2.17.1
#33 lore raw

PATCH 35/76 tc-testing: add test-cases for numeric and invalid control action

In reply to Sasha Levin

From: Paolo Abeni <[email protected]>

[ Upstream commit 25a8238f4cc8425d4aade4f9041be468d0e8aa2e ]

Only the police action allows us to specify an arbitrary numeric value for the control action. This change introduces an explicit test case for the above feature and then leverage it for testing the kernel behavior for invalid control actions (reject).

---
 .../tc-testing/tc-tests/actions/police.json   | 48 +++++++++++++++++++
 1 file changed, 48 insertions(+)
tools/testing/selftests/tc-testing/tc-tests/actions/police.json +48 -0
index f03763d81617..30f9b54bd666 100644
@@ -312,6 +312,54 @@
             "$TC actions flush action police"
         ]
     },
+    {
+        "id": "6aaf",
+        "name": "Add police actions with conform-exceed control pass/pipe [with numeric values]",
+        "category": [
+            "actions",
+            "police"
+        ],
+        "setup": [
+            [
+                "$TC actions flush action police",
+                0,
+                1,
+                255
+            ]
+        ],
+        "cmdUnderTest": "$TC actions add action police rate 3mbit burst 250k conform-exceed 0/3 index 1",
+        "expExitCode": "0",
+        "verifyCmd": "$TC actions get action police index 1",
+        "matchPattern": "action order [0-9]*:  police 0x1 rate 3Mbit burst 250Kb mtu 2Kb action pass/pipe",
+        "matchCount": "1",
+        "teardown": [
+            "$TC actions flush action police"
+        ]
+    },
+    {
+        "id": "29b1",
+        "name": "Add police actions with conform-exceed control <invalid>/drop",
+        "category": [
+            "actions",
+            "police"
+        ],
+        "setup": [
+            [
+                "$TC actions flush action police",
+                0,
+                1,
+                255
+            ]
+        ],
+        "cmdUnderTest": "$TC actions add action police rate 3mbit burst 250k conform-exceed 10/drop index 1",
+        "expExitCode": "255",
+        "verifyCmd": "$TC actions ls action police",
+        "matchPattern": "action order [0-9]*:  police 0x1 rate 3Mbit burst 250Kb mtu 2Kb action ",
+        "matchCount": "0",
+        "teardown": [
+            "$TC actions flush action police"
+        ]
+    },
     {
         "id": "c26f",
         "name": "Add police action with invalid peakrate value",
Signature · 1 line
2.17.1
#34 lore raw

PATCH 36/76 cfg80211: nl80211_update_ft_ies() to validate NL80211_ATTR_IE

In reply to Sasha Levin

From: Arunk Khandavalli <[email protected]>

[ Upstream commit 4f0223bfe9c3e62d8f45a85f1ef1b18a8a263ef9 ]

nl80211_update_ft_ies() tried to validate NL80211_ATTR_IE with is_valid_ie_attr() before dereferencing it, but that helper function returns true in case of NULL pointer (i.e., attribute not included). This can result to dereferencing a NULL pointer. Fix that by explicitly checking that NL80211_ATTR_IE is included.

Fixes 355199e02b83 ("cfg80211: Extend support for IEEE 802.11r Fast BSS Transition")
---
 net/wireless/nl80211.c | 1 +
 1 file changed, 1 insertion(+)
net/wireless/nl80211.c +1 -0
index ce0149a86c13..733ccf867972 100644
@@ -12099,6 +12099,7 @@ static int nl80211_update_ft_ies(struct sk_buff *skb, struct genl_info *info)
 		return -EOPNOTSUPP;
 
 	if (!info->attrs[NL80211_ATTR_MDID] ||
+	    !info->attrs[NL80211_ATTR_IE] ||
 	    !is_valid_ie_attr(info->attrs[NL80211_ATTR_IE]))
 		return -EINVAL;
 
Signature · 1 line
2.17.1
#35 lore raw

PATCH 37/76 mac80211: do not convert to A-MSDU if frag/subframe limited

In reply to Sasha Levin

From: Lorenzo Bianconi <[email protected]>

[ Upstream commit 1eb507903665442360a959136dfa3234c43db085 ]

Do not start to aggregate packets in a A-MSDU frame (converting the first subframe to A-MSDU, adding the header) if max_tx_fragments or max_amsdu_subframes limits are already exceeded by it. In particular, this happens when drivers set the limit to 1 to avoid A-MSDUs at all.

[reword commit message to be more precise]
---
 net/mac80211/tx.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
net/mac80211/tx.c +3 -3
index 667a73d6eb5c..1aac5e3c7eee 100644
@@ -3208,9 +3208,6 @@ static bool ieee80211_amsdu_aggregate(struct ieee80211_sub_if_data *sdata,
 	if (skb->len + head->len > max_amsdu_len)
 		goto out;
 
-	if (!ieee80211_amsdu_prepare_head(sdata, fast_tx, head))
-		goto out;
-
 	nfrags = 1 + skb_shinfo(skb)->nr_frags;
 	nfrags += 1 + skb_shinfo(head)->nr_frags;
 	frag_tail = &skb_shinfo(head)->frag_list;
@@ -3226,6 +3223,9 @@ static bool ieee80211_amsdu_aggregate(struct ieee80211_sub_if_data *sdata,
 	if (max_frags && nfrags > max_frags)
 		goto out;
 
+	if (!ieee80211_amsdu_prepare_head(sdata, fast_tx, head))
+		goto out;
+
 	/*
 	 * Pad out the previous subframe to a multiple of 4 by adding the
 	 * padding to the next one, that's being added. Note that head->len
Signature · 1 line
2.17.1
#36 lore raw

PATCH 38/76 mac80211: always account for A-MSDU header changes

In reply to Sasha Levin

From: Johannes Berg <[email protected]>

[ Upstream commit aa58acf325b4aadeecae2bfc90658273b47dbace ]

In the error path of changing the SKB headroom of the second A-MSDU subframe, we would not account for the already-changed length of the first frame that just got converted to be in A-MSDU format and thus is a bit longer now.

Fix this by doing the necessary accounting.

It would be possible to reorder the operations, but that would make the code more complex (to calculate the necessary pad), and the headroom expansion should not fail frequently enough to make that worthwhile.

Fixes 6e0456b54545 ("mac80211: add A-MSDU tx support")
---
 net/mac80211/tx.c | 12 +++++++-----
 1 file changed, 7 insertions(+), 5 deletions(-)
net/mac80211/tx.c +7 -5
index 1aac5e3c7eee..6ca0865de945 100644
@@ -3239,7 +3239,7 @@ static bool ieee80211_amsdu_aggregate(struct ieee80211_sub_if_data *sdata,
 
 	if (!ieee80211_amsdu_realloc_pad(local, skb, sizeof(rfc1042_header) +
 						     2 + pad))
-		goto out;
+		goto out_recalc;
 
 	ret = true;
 	data = skb_push(skb, ETH_ALEN + 2);
@@ -3256,11 +3256,13 @@ static bool ieee80211_amsdu_aggregate(struct ieee80211_sub_if_data *sdata,
 	head->data_len += skb->len;
 	*frag_tail = skb;
 
-	flow->backlog += head->len - orig_len;
-	tin->backlog_bytes += head->len - orig_len;
-
-	fq_recalc_backlog(fq, tin, flow);
+out_recalc:
+	if (head->len != orig_len) {
+		flow->backlog += head->len - orig_len;
+		tin->backlog_bytes += head->len - orig_len;
 
+		fq_recalc_backlog(fq, tin, flow);
+	}
 out:
 	spin_unlock_bh(&fq->lock);
 
Signature · 1 line
2.17.1
#37 lore raw

PATCH 39/76 tools/kvm_stat: fix python3 issues

In reply to Sasha Levin

From: Stefan Raspl <[email protected]>

[ Upstream commit 58f33cfe73076b6497bada4f7b5bda961ed68083 ]

Python3 returns a float for a regular division - switch to a division operator that returns an integer.
Furthermore, filters return a generator object instead of the actual list - wrap result in yet another list, which makes it still work in both, Python2 and 3.

---
 tools/kvm/kvm_stat/kvm_stat | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
tools/kvm/kvm_stat/kvm_stat +3 -3
index 56c4b3f8a01b..e10b90a8917a 100755
@@ -759,7 +759,7 @@ class DebugfsProvider(Provider):
             if len(vms) == 0:
                 self.do_read = False
 
-            self.paths = filter(lambda x: "{}-".format(pid) in x, vms)
+            self.paths = list(filter(lambda x: "{}-".format(pid) in x, vms))
 
         else:
             self.paths = []
@@ -1219,10 +1219,10 @@ class Tui(object):
         (x, term_width) = self.screen.getmaxyx()
         row = 2
         for line in text:
-            start = (term_width - len(line)) / 2
+            start = (term_width - len(line)) // 2
             self.screen.addstr(row, start, line)
             row += 1
-        self.screen.addstr(row + 1, (term_width - len(hint)) / 2, hint,
+        self.screen.addstr(row + 1, (term_width - len(hint)) // 2, hint,
                            curses.A_STANDOUT)
         self.screen.getkey()
 
Signature · 1 line
2.17.1
#38 lore raw

PATCH 40/76 tools/kvm_stat: fix handling of invalid paths in debugfs provider

In reply to Sasha Levin

From: Stefan Raspl <[email protected]>

[ Upstream commit 617c66b9f236d20f11cecbb3f45e6d5675b2fae1 ]

When filtering by guest, kvm_stat displays garbage when the guest is destroyed - see sample output below.
We add code to remove the invalid paths from the providers, so at least no more garbage is displayed.
Here's a sample output to illustrate:

kvm statistics - pid 13986 (foo)

Event Total %Total CurAvg/s

   diagnose_258                                     -2    0.0        0
   deliver_program_interruption                     -3    0.0        0
   diagnose_308                                     -4    0.0        0
   halt_poll_invalid                               -91    0.0       -6
   deliver_service_signal                         -244    0.0      -16
   halt_successful_poll                           -250    0.1      -17
   exit_pei                                       -285    0.1      -19
   exit_external_request                          -312    0.1      -21
   diagnose_9c                                    -328    0.1      -22
   userspace_handled                              -713    0.1      -47
   halt_attempted_poll                            -939    0.2      -62
   deliver_emergency_signal                      -3126    0.6     -208
   halt_wakeup                                   -7199    1.5     -481
   exit_wait_state                               -7379    1.5     -493
   diagnose_500                                 -56499   11.5    -3757
   exit_null                                    -85491   17.4    -5685
   diagnose_44                                 -133300   27.1    -8874
   exit_instruction                            -195898   39.8   -13037

Total -492063

---
 tools/kvm/kvm_stat/kvm_stat | 8 ++++++++
 1 file changed, 8 insertions(+)
tools/kvm/kvm_stat/kvm_stat +8 -0
index e10b90a8917a..b9e8d0def1ab 100755
@@ -766,6 +766,13 @@ class DebugfsProvider(Provider):
             self.do_read = True
         self.reset()
 
+    def _verify_paths(self):
+        """Remove invalid paths"""
+        for path in self.paths:
+            if not os.path.exists(os.path.join(PATH_DEBUGFS_KVM, path)):
+                self.paths.remove(path)
+                continue
+
     def read(self, reset=0, by_guest=0):
         """Returns a dict with format:'file name / field -> current value'.
 
@@ -780,6 +787,7 @@ class DebugfsProvider(Provider):
         # If no debugfs filtering support is available, then don't read.
         if not self.do_read:
             return results
+        self._verify_paths()
 
         paths = self.paths
         if self._pid == 0:
Signature · 1 line
2.17.1
#39 lore raw

PATCH 41/76 tools/kvm_stat: fix updates for dead guests

In reply to Sasha Levin

From: Stefan Raspl <[email protected]>

[ Upstream commit 710ab11ad9329d2d4b044405e328c994b19a2aa9 ]

With pid filtering active, when a guest is removed e.g. via virsh shutdown, successive updates produce garbage.
Therefore, we add code to detect this case and prevent further body updates. Note that when displaying the help dialog via 'h' in this case, once we exit we're stuck with the 'Collecting data...' message till we remove the filter.

---
 tools/kvm/kvm_stat/kvm_stat | 11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)
tools/kvm/kvm_stat/kvm_stat +10 -1
index b9e8d0def1ab..7c92545931e3 100755
@@ -1170,6 +1170,9 @@ class Tui(object):
 
             return sorted_items
 
+        if not self._is_running_guest(self.stats.pid_filter):
+            # leave final data on screen
+            return
         row = 3
         self.screen.move(row, 0)
         self.screen.clrtobot()
@@ -1327,6 +1330,12 @@ class Tui(object):
                 msg = '"' + str(val) + '": Invalid value'
         self._refresh_header()
 
+    def _is_running_guest(self, pid):
+        """Check if pid is still a running process."""
+        if not pid:
+            return True
+        return os.path.isdir(os.path.join('/proc/', str(pid)))
+
     def _show_vm_selection_by_guest(self):
         """Draws guest selection mask.
 
@@ -1354,7 +1363,7 @@ class Tui(object):
             if not guest or guest == '0':
                 break
             if guest.isdigit():
-                if not os.path.isdir(os.path.join('/proc/', guest)):
+                if not self._is_running_guest(guest):
                     msg = '"' + guest + '": Not a running process'
                     continue
                 pid = int(guest)
Signature · 1 line
2.17.1
#40 lore raw

PATCH 42/76 gpio: Fix crash due to registration race

In reply to Sasha Levin

From: Vincent Whitchurch <[email protected]>

[ Upstream commit d49b48f088c323dbacae44dfbe56d9c985c8a2a1 ]

gpiochip_add_data_with_key() adds the gpiochip to the gpio_devices list before of_gpiochip_add() is called, but it's only the latter which sets the ->of_xlate function pointer. gpiochip_find() can be called by someone else between these two actions, and it can find the chip and call of_gpiochip_match_node_and_xlate() which leads to the following crash due to a NULL ->of_xlate().

Unhandled prefetch abort: page domain fault (0x01b) at 0x00000000

 Modules linked in: leds_gpio(+) gpio_generic(+)
 CPU: 0 PID: 830 Comm: insmod Not tainted 4.18.0+ #43
 Hardware name: ARM-Versatile Express
 PC is at   (null)
 LR is at of_gpiochip_match_node_and_xlate+0x2c/0x38
 Process insmod (pid: 830, stack limit = 0x(ptrval))
  (of_gpiochip_match_node_and_xlate) from  (gpiochip_find+0x48/0x84)
  (gpiochip_find) from  (of_get_named_gpiod_flags+0xa8/0x238)
  (of_get_named_gpiod_flags) from  (gpiod_get_from_of_node+0x2c/0xc8)
  (gpiod_get_from_of_node) from  (devm_fwnode_get_index_gpiod_from_child+0xb8/0x144)
  (devm_fwnode_get_index_gpiod_from_child) from  (gpio_led_probe+0x208/0x3c4 [leds_gpio])
  (gpio_led_probe [leds_gpio]) from  (platform_drv_probe+0x48/0x9c)
  (platform_drv_probe) from  (really_probe+0x1d0/0x3d4)
  (really_probe) from  (driver_probe_device+0x78/0x1c0)
  (driver_probe_device) from  (__driver_attach+0x120/0x13c)
  (__driver_attach) from  (bus_for_each_dev+0x68/0xb4)
  (bus_for_each_dev) from  (bus_add_driver+0x1a8/0x268)
  (bus_add_driver) from  (driver_register+0x78/0x10c)
  (driver_register) from  (do_one_initcall+0x54/0x1fc)
  (do_one_initcall) from  (do_init_module+0x64/0x1f4)
  (do_init_module) from  (load_module+0x2198/0x26ac)
  (load_module) from  (sys_finit_module+0xe0/0x110)
  (sys_finit_module) from  (ret_fast_syscall+0x0/0x54)

One way to fix this would be to rework the hairy registration sequence in gpiochip_add_data_with_key(), but since I'd probably introduce a couple of new bugs if I attempted that, simply add a check for a non-NULL of_xlate function pointer in of_gpiochip_match_node_and_xlate(). This works since the driver looking for the gpio will simply fail to find the gpio and defer its probe and be reprobed when the driver which is registering the gpiochip has fully completed its probe.

---
 drivers/gpio/gpiolib-of.c | 1 +
 1 file changed, 1 insertion(+)
drivers/gpio/gpiolib-of.c +1 -0
index 53a14ee8ad6d..a704d2e74421 100644
@@ -31,6 +31,7 @@ static int of_gpiochip_match_node_and_xlate(struct gpio_chip *chip, void *data)
 	struct of_phandle_args *gpiospec = data;
 
 	return chip->gpiodev->dev.of_node == gpiospec->np &&
+				chip->of_xlate &&
 				chip->of_xlate(chip, gpiospec, NULL) >= 0;
 }
 
Signature · 1 line
2.17.1
#41 lore raw

PATCH 43/76 ARC: atomics: unbork atomic_fetch_##op()

In reply to Sasha Levin

From: Will Deacon <[email protected]>

[ Upstream commit 3fcbb8260a87efb691d837e8cd24e81f65b3eb70 ]

In 4.19-rc1, Eugeniy reported weird boot and IO errors on ARC HSDK

| INFO: task syslogd:77 blocked for more than 10 seconds.
|       Not tainted 4.19.0-rc1-00007-gf213acea4e88 #40
| "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this
| message.
| syslogd         D    0    77     76 0x00000000
|
| Stack Trace:
|  __switch_to+0x0/0xac
|  __schedule+0x1b2/0x730
|  io_schedule+0x5c/0xc0
|  __lock_page+0x98/0xdc
|  find_lock_entry+0x38/0x100
|  shmem_getpage_gfp.isra.3+0x82/0xbfc
|  shmem_fault+0x46/0x138
|  handle_mm_fault+0x5bc/0x924
|  do_page_fault+0x100/0x2b8
|  ret_from_exception+0x0/0x8

He bisected to 84c6591103db ("locking/atomics, asm-generic/bitops/lock.h: Rewrite using atomic_fetch_*()")

This commit however only unmasked the real issue introduced by commit 4aef66c8ae9 ("locking/atomic, arch/arc: Fix build") which missed the retry-if-scond-failed branch in atomic_fetch_##op() macros.

The bisected commit started using atomic_fetch_##op() macros for building the rest of atomics.

Fixes 4aef66c8ae9 ("locking/atomic, arch/arc: Fix build")
[vgupta: wrote changelog]
---
 arch/arc/include/asm/atomic.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arc/include/asm/atomic.h +1 -1
index 11859287c52a..c98b59ac0612 100644
@@ -84,7 +84,7 @@ static inline int atomic_fetch_##op(int i, atomic_t *v)			\
 	"1:	llock   %[orig], [%[ctr]]		\n"		\
 	"	" #asm_op " %[val], %[orig], %[i]	\n"		\
 	"	scond   %[val], [%[ctr]]		\n"		\
-	"						\n"		\
+	"	bnz     1b				\n"		\
 	: [val]	"=&r"	(val),						\
 	  [orig] "=&r" (orig)						\
 	: [ctr]	"r"	(&v->counter),					\
Signature · 1 line
2.17.1
#42 lore raw

PATCH 44/76 Revert "blk-throttle: fix race between blkcg_bio_issue_check() and cgroup_rmdir()"

In reply to Sasha Levin

From: "Dennis Zhou (Facebook)" <[email protected]>

[ Upstream commit 6b06546206868f723f2061d703a3c3c378dcbf4c ]

This reverts commit 4c6994806f708559c2812b73501406e21ae5dcd0.

Destroying blkgs is tricky because of the nature of the relationship. A blkg should go away when either a blkcg or a request_queue goes away. However, blkg's pin the blkcg to ensure they remain valid. To break this cycle, when a blkcg is offlined, blkgs put back their css ref. This eventually lets css_free() get called which frees the blkcg.

The above commit (4c6994806f70) breaks this order of events by trying to destroy blkgs in css_free(). As the blkgs still hold references to the blkcg, css_free() is never called.

The race between blkcg_bio_issue_check() and cgroup_rmdir() will be addressed in the following patch by delaying destruction of a blkg until all writeback associated with the blkcg has been finished.

Fixes 4c6994806f70 ("blk-throttle: fix race between blkcg_bio_issue_check() and cgroup_rmdir()")
Cc Jiufei Xue <[email protected]>
Cc Joseph Qi <[email protected]>
Cc Tejun Heo <[email protected]>
Cc Jens Axboe <[email protected]>
---
 block/blk-cgroup.c         | 78 ++++++++------------------------------
 include/linux/blk-cgroup.h |  1 -
 2 files changed, 16 insertions(+), 63 deletions(-)
block/blk-cgroup.c +16 -62
index eb85cb87c40f..ec868373b11b 100644
@@ -307,28 +307,11 @@ struct blkcg_gq *blkg_lookup_create(struct blkcg *blkcg,
 	}
 }
 
-static void blkg_pd_offline(struct blkcg_gq *blkg)
-{
-	int i;
-
-	lockdep_assert_held(blkg->q->queue_lock);
-	lockdep_assert_held(&blkg->blkcg->lock);
-
-	for (i = 0; i < BLKCG_MAX_POLS; i++) {
-		struct blkcg_policy *pol = blkcg_policy[i];
-
-		if (blkg->pd[i] && !blkg->pd[i]->offline &&
-		    pol->pd_offline_fn) {
-			pol->pd_offline_fn(blkg->pd[i]);
-			blkg->pd[i]->offline = true;
-		}
-	}
-}
-
 static void blkg_destroy(struct blkcg_gq *blkg)
 {
 	struct blkcg *blkcg = blkg->blkcg;
 	struct blkcg_gq *parent = blkg->parent;
+	int i;
 
 	lockdep_assert_held(blkg->q->queue_lock);
 	lockdep_assert_held(&blkcg->lock);
@@ -337,6 +320,13 @@ static void blkg_destroy(struct blkcg_gq *blkg)
 	WARN_ON_ONCE(list_empty(&blkg->q_node));
 	WARN_ON_ONCE(hlist_unhashed(&blkg->blkcg_node));
 
+	for (i = 0; i < BLKCG_MAX_POLS; i++) {
+		struct blkcg_policy *pol = blkcg_policy[i];
+
+		if (blkg->pd[i] && pol->pd_offline_fn)
+			pol->pd_offline_fn(blkg->pd[i]);
+	}
+
 	if (parent) {
 		blkg_rwstat_add_aux(&parent->stat_bytes, &blkg->stat_bytes);
 		blkg_rwstat_add_aux(&parent->stat_ios, &blkg->stat_ios);
@@ -379,7 +369,6 @@ static void blkg_destroy_all(struct request_queue *q)
 		struct blkcg *blkcg = blkg->blkcg;
 
 		spin_lock(&blkcg->lock);
-		blkg_pd_offline(blkg);
 		blkg_destroy(blkg);
 		spin_unlock(&blkcg->lock);
 	}
@@ -1006,54 +995,21 @@ static struct cftype blkcg_legacy_files[] = {
  * @css: css of interest
  *
  * This function is called when @css is about to go away and responsible
- * for offlining all blkgs pd and killing all wbs associated with @css.
- * blkgs pd offline should be done while holding both q and blkcg locks.
- * As blkcg lock is nested inside q lock, this function performs reverse
- * double lock dancing.
+ * for shooting down all blkgs associated with @css.  blkgs should be
+ * removed while holding both q and blkcg locks.  As blkcg lock is nested
+ * inside q lock, this function performs reverse double lock dancing.
  *
  * This is the blkcg counterpart of ioc_release_fn().
  */
 static void blkcg_css_offline(struct cgroup_subsys_state *css)
 {
 	struct blkcg *blkcg = css_to_blkcg(css);
-	struct blkcg_gq *blkg;
 
 	spin_lock_irq(&blkcg->lock);
 
-	hlist_for_each_entry(blkg, &blkcg->blkg_list, blkcg_node) {
-		struct request_queue *q = blkg->q;
-
-		if (spin_trylock(q->queue_lock)) {
-			blkg_pd_offline(blkg);
-			spin_unlock(q->queue_lock);
-		} else {
-			spin_unlock_irq(&blkcg->lock);
-			cpu_relax();
-			spin_lock_irq(&blkcg->lock);
-		}
-	}
-
-	spin_unlock_irq(&blkcg->lock);
-
-	wb_blkcg_offline(blkcg);
-}
-
-/**
- * blkcg_destroy_all_blkgs - destroy all blkgs associated with a blkcg
- * @blkcg: blkcg of interest
- *
- * This function is called when blkcg css is about to free and responsible for
- * destroying all blkgs associated with @blkcg.
- * blkgs should be removed while holding both q and blkcg locks. As blkcg lock
- * is nested inside q lock, this function performs reverse double lock dancing.
- */
-static void blkcg_destroy_all_blkgs(struct blkcg *blkcg)
-{
-	spin_lock_irq(&blkcg->lock);
 	while (!hlist_empty(&blkcg->blkg_list)) {
 		struct blkcg_gq *blkg = hlist_entry(blkcg->blkg_list.first,
-						    struct blkcg_gq,
-						    blkcg_node);
+						struct blkcg_gq, blkcg_node);
 		struct request_queue *q = blkg->q;
 
 		if (spin_trylock(q->queue_lock)) {
@@ -1065,7 +1021,10 @@ static void blkcg_destroy_all_blkgs(struct blkcg *blkcg)
 			spin_lock_irq(&blkcg->lock);
 		}
 	}
+
 	spin_unlock_irq(&blkcg->lock);
+
+	wb_blkcg_offline(blkcg);
 }
 
 static void blkcg_css_free(struct cgroup_subsys_state *css)
@@ -1073,8 +1032,6 @@ static void blkcg_css_free(struct cgroup_subsys_state *css)
 	struct blkcg *blkcg = css_to_blkcg(css);
 	int i;
 
-	blkcg_destroy_all_blkgs(blkcg);
-
 	mutex_lock(&blkcg_pol_mutex);
 
 	list_del(&blkcg->all_blkcgs_node);
@@ -1412,11 +1369,8 @@ void blkcg_deactivate_policy(struct request_queue *q,
 
 	list_for_each_entry(blkg, &q->blkg_list, q_node) {
 		if (blkg->pd[pol->plid]) {
-			if (!blkg->pd[pol->plid]->offline &&
-			    pol->pd_offline_fn) {
+			if (pol->pd_offline_fn)
 				pol->pd_offline_fn(blkg->pd[pol->plid]);
-				blkg->pd[pol->plid]->offline = true;
-			}
 			pol->pd_free_fn(blkg->pd[pol->plid]);
 			blkg->pd[pol->plid] = NULL;
 		}
include/linux/blk-cgroup.h +0 -1
index 0fce47d5acb1..5d46b83d4820 100644
@@ -88,7 +88,6 @@ struct blkg_policy_data {
 	/* the blkg and policy id this per-policy data belongs to */
 	struct blkcg_gq			*blkg;
 	int				plid;
-	bool				offline;
 };
 
 /*
Signature · 1 line
2.17.1
#43 lore raw

PATCH 45/76 md/raid5-cache: disable reshape completely

In reply to Sasha Levin

From: Shaohua Li <[email protected]>

[ Upstream commit e254de6bcf3f5b6e78a92ac95fb91acef8adfe1a ]

We don't support reshape yet if an array supports log device. Previously we determine the fact by checking ->log. However, ->log could be NULL after a log device is removed, but the array is still marked to support log device. Don't allow reshape in this case too. User can disable log device support by setting 'consistency_policy' to 'resync' then do reshape.

---
 drivers/md/raid5-log.h | 5 +++++
 drivers/md/raid5.c     | 6 +++---
 2 files changed, 8 insertions(+), 3 deletions(-)
drivers/md/raid5-log.h +5 -0
index a001808a2b77..bfb811407061 100644
@@ -46,6 +46,11 @@ extern int ppl_modify_log(struct r5conf *conf, struct md_rdev *rdev, bool add);
 extern void ppl_quiesce(struct r5conf *conf, int quiesce);
 extern int ppl_handle_flush_request(struct r5l_log *log, struct bio *bio);
 
+static inline bool raid5_has_log(struct r5conf *conf)
+{
+	return test_bit(MD_HAS_JOURNAL, &conf->mddev->flags);
+}
+
 static inline bool raid5_has_ppl(struct r5conf *conf)
 {
 	return test_bit(MD_HAS_PPL, &conf->mddev->flags);
drivers/md/raid5.c +3 -3
index 49107c52c8e6..9050bfc71309 100644
@@ -735,7 +735,7 @@ static bool stripe_can_batch(struct stripe_head *sh)
 {
 	struct r5conf *conf = sh->raid_conf;
 
-	if (conf->log || raid5_has_ppl(conf))
+	if (raid5_has_log(conf) || raid5_has_ppl(conf))
 		return false;
 	return test_bit(STRIPE_BATCH_READY, &sh->state) &&
 		!test_bit(STRIPE_BITMAP_PENDING, &sh->state) &&
@@ -7739,7 +7739,7 @@ static int raid5_resize(struct mddev *mddev, sector_t sectors)
 	sector_t newsize;
 	struct r5conf *conf = mddev->private;
 
-	if (conf->log || raid5_has_ppl(conf))
+	if (raid5_has_log(conf) || raid5_has_ppl(conf))
 		return -EINVAL;
 	sectors &= ~((sector_t)conf->chunk_sectors - 1);
 	newsize = raid5_size(mddev, sectors, mddev->raid_disks);
@@ -7790,7 +7790,7 @@ static int check_reshape(struct mddev *mddev)
 {
 	struct r5conf *conf = mddev->private;
 
-	if (conf->log || raid5_has_ppl(conf))
+	if (raid5_has_log(conf) || raid5_has_ppl(conf))
 		return -EINVAL;
 	if (mddev->delta_disks == 0 &&
 	    mddev->new_layout == mddev->layout &&
Signature · 1 line
2.17.1
#44 lore raw

PATCH 46/76 RAID10 BUG_ON in raise_barrier when force is true and conf->barrier is 0

In reply to Sasha Levin

From: Xiao Ni <[email protected]>

[ Upstream commit 1d0ffd264204eba1861865560f1f7f7a92919384 ]

In raid10 reshape_request it gets max_sectors in read_balance. If the underlayer disks have bad blocks, the max_sectors is less than last. It will call goto read_more many times. It calls raise_barrier(conf, sectors_done != 0) every time. In this condition sectors_done is not 0. So the value passed to the argument force of raise_barrier is true.

In raise_barrier it checks conf->barrier when force is true. If force is true and conf->barrier is 0, it panic. In this case reshape_request submits bio to under layer disks. And in the callback function of the bio it calls lower_barrier. If the bio finishes before calling raise_barrier again, it can trigger the BUG_ON.

Add one pair of raise_barrier/lower_barrier to fix this bug.

---
 drivers/md/raid10.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/md/raid10.c +4 -1
index 35bd3a62451b..8c93d44a052c 100644
@@ -4531,11 +4531,12 @@ static sector_t reshape_request(struct mddev *mddev, sector_t sector_nr,
 		allow_barrier(conf);
 	}
 
+	raise_barrier(conf, 0);
 read_more:
 	/* Now schedule reads for blocks from sector_nr to last */
 	r10_bio = raid10_alloc_init_r10buf(conf);
 	r10_bio->state = 0;
-	raise_barrier(conf, sectors_done != 0);
+	raise_barrier(conf, 1);
 	atomic_set(&r10_bio->remaining, 0);
 	r10_bio->mddev = mddev;
 	r10_bio->sector = sector_nr;
@@ -4631,6 +4632,8 @@ static sector_t reshape_request(struct mddev *mddev, sector_t sector_nr,
 	if (sector_nr <= last)
 		goto read_more;
 
+	lower_barrier(conf);
+
 	/* Now that we have done the whole section we can
 	 * update reshape_progress
 	 */
Signature · 1 line
2.17.1
#45 lore raw

PATCH 47/76 selftests: pmtu: maximum MTU for vti4 is 2^16-1-20

In reply to Sasha Levin

From: Sabrina Dubroca <[email protected]>

[ Upstream commit 902b5417f28d955cdb4898df6ffaab15f56c5cff ]

Since commit 82612de1c98e ("ip_tunnel: restore binding to ifaces with a large mtu"), the maximum MTU for vti4 is based on IP_MAX_MTU instead of the mysterious constant 0xFFF8. This makes this selftest fail.

Fixes 82612de1c98e ("ip_tunnel: restore binding to ifaces with a large mtu")
---
 tools/testing/selftests/net/pmtu.sh | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
tools/testing/selftests/net/pmtu.sh +1 -1
index f8cc38afffa2..0ecf2609b9a4 100755
@@ -334,7 +334,7 @@ test_pmtu_vti4_link_add_mtu() {
 	fail=0
 
 	min=68
-	max=$((65528 - 20))
+	max=$((65535 - 20))
 	# Check invalid values first
 	for v in $((min - 1)) $((max + 1)); do
 		${ns_a} ip link add vti4_a mtu ${v} type vti local ${veth4_a_addr} remote ${veth4_b_addr} key 10 2>/dev/null
Signature · 1 line
2.17.1
#46 lore raw

PATCH 48/76 selftests: pmtu: detect correct binary to ping ipv6 addresses

In reply to Sasha Levin

From: Sabrina Dubroca <[email protected]>

[ Upstream commit c81c7012e0c769b5704c2b07bd5224965e76fb70 ]

Some systems don't have the ping6 binary anymore, and use ping for everything. Detect the absence of ping6 and try to use ping instead.

Fixes d1f1b9cbf34c ("selftests: net: Introduce first PMTU test")
---
 tools/testing/selftests/net/pmtu.sh | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
tools/testing/selftests/net/pmtu.sh +4 -1
index 0ecf2609b9a4..32a194e3e07a 100755
@@ -46,6 +46,9 @@
 # Kselftest framework requirement - SKIP code is 4.
 ksft_skip=4
 
+# Some systems don't have a ping6 binary anymore
+which ping6 > /dev/null 2>&1 && ping6=$(which ping6) || ping6=$(which ping)
+
 tests="
 	pmtu_vti6_exception		vti6: PMTU exceptions
 	pmtu_vti4_exception		vti4: PMTU exceptions
@@ -274,7 +277,7 @@ test_pmtu_vti6_exception() {
 	mtu "${ns_b}" veth_b 4000
 	mtu "${ns_a}" vti6_a 5000
 	mtu "${ns_b}" vti6_b 5000
-	${ns_a} ping6 -q -i 0.1 -w 2 -s 60000 ${vti6_b_addr} > /dev/null
+	${ns_a} ${ping6} -q -i 0.1 -w 2 -s 60000 ${vti6_b_addr} > /dev/null
 
 	# Check that exception was created
 	if [ "$(route_get_dst_pmtu_from_exception "${ns_a}" ${vti6_b_addr})" = "" ]; then
Signature · 1 line
2.17.1
#47 lore raw

PATCH 49/76 ibmvnic: Include missing return code checks in reset function

In reply to Sasha Levin

From: Thomas Falcon <[email protected]>

[ Upstream commit f611a5b4a51fa36a0aa792be474f5d6aacaef7e3 ]

Check the return codes of these functions and halt reset in case of failure. The driver will remain in a dormant state until the next reset event, when device initialization will be re-attempted.

---
 drivers/net/ethernet/ibm/ibmvnic.c | 12 +++++++++---
 1 file changed, 9 insertions(+), 3 deletions(-)
drivers/net/ethernet/ibm/ibmvnic.c +9 -3
index ffe7acbeaa22..d834308adf95 100644
@@ -1841,11 +1841,17 @@ static int do_reset(struct ibmvnic_adapter *adapter,
 			adapter->map_id = 1;
 			release_rx_pools(adapter);
 			release_tx_pools(adapter);
-			init_rx_pools(netdev);
-			init_tx_pools(netdev);
+			rc = init_rx_pools(netdev);
+			if (rc)
+				return rc;
+			rc = init_tx_pools(netdev);
+			if (rc)
+				return rc;
 
 			release_napi(adapter);
-			init_napi(adapter);
+			rc = init_napi(adapter);
+			if (rc)
+				return rc;
 		} else {
 			rc = reset_tx_pools(adapter);
 			if (rc)
Signature · 1 line
2.17.1
#48 lore raw

PATCH 50/76 bpf: Fix bpf_msg_pull_data()

In reply to Sasha Levin

From: Tushar Dave <[email protected]>

[ Upstream commit 9db39f4d4f94b61e4b64b077f6ddb2bdfb533a88 ]

Helper bpf_msg_pull_data() mistakenly reuses variable 'offset' while linearizing multiple scatterlist elements. Variable 'offset' is used to find first starting scatterlist element

    i.e. msg->data = sg_virt(&sg[first_sg]) + start - offset"

Use different variable name while linearizing multiple scatterlist elements so that value contained in variable 'offset' won't get overwritten.

Fixes 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data")
---
 net/core/filter.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)
net/core/filter.c +3 -4
index a80b57e4aaed..963ee2e88861 100644
@@ -2282,7 +2282,7 @@ static const struct bpf_func_proto bpf_msg_cork_bytes_proto = {
 BPF_CALL_4(bpf_msg_pull_data,
 	   struct sk_msg_buff *, msg, u32, start, u32, end, u64, flags)
 {
-	unsigned int len = 0, offset = 0, copy = 0;
+	unsigned int len = 0, offset = 0, copy = 0, poffset = 0;
 	int bytes = end - start, bytes_sg_total;
 	struct scatterlist *sg = msg->sg_data;
 	int first_sg, last_sg, i, shift;
@@ -2338,16 +2338,15 @@ BPF_CALL_4(bpf_msg_pull_data,
 	if (unlikely(!page))
 		return -ENOMEM;
 	p = page_address(page);
-	offset = 0;
 
 	i = first_sg;
 	do {
 		from = sg_virt(&sg[i]);
 		len = sg[i].length;
-		to = p + offset;
+		to = p + poffset;
 
 		memcpy(to, from, len);
-		offset += len;
+		poffset += len;
 		sg[i].length = 0;
 		put_page(sg_page(&sg[i]));
 
Signature · 1 line
2.17.1
#49 lore raw

PATCH 51/76 bpf: avoid misuse of psock when TCP_ULP_BPF collides with another ULP

In reply to Sasha Levin

From: John Fastabend <[email protected]>

[ Upstream commit 597222f72a94118f593e4f32bf58ae7e049a0df1 ]

Currently we check sk_user_data is non NULL to determine if the sk exists in a map. However, this is not sufficient to ensure the psock or the ULP ops are not in use by another user, such as kcm or TLS. To avoid this when adding a sock to a map also verify it is of the correct ULP type. Additionally, when releasing a psock verify that it is the TCP_ULP_BPF type before releasing the ULP. The error case where we abort an update due to ULP collision can cause this error path.

For example,

__sock_map_ctx_update_elem()
[...]
err = tcp_set_ulp_id(sock, TCP_ULP_BPF) <- collides with TLS
if (err) <- so err out here
goto out_free
[...]
out_free:
smap_release_sock() <- calling tcp_cleanup_ulp releases the
TLS ULP incorrectly.

Fixes 2f857d04601a ("bpf: sockmap, remove STRPARSER map_flags and add multi-map support")
---
 kernel/bpf/sockmap.c | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)
kernel/bpf/sockmap.c +11 -1
index 2ddf1501aace..9463e135812e 100644
@@ -1462,10 +1462,16 @@ static void smap_destroy_psock(struct rcu_head *rcu)
 	schedule_work(&psock->gc_work);
 }
 
+static bool psock_is_smap_sk(struct sock *sk)
+{
+	return inet_csk(sk)->icsk_ulp_ops == &bpf_tcp_ulp_ops;
+}
+
 static void smap_release_sock(struct smap_psock *psock, struct sock *sock)
 {
 	if (refcount_dec_and_test(&psock->refcnt)) {
-		tcp_cleanup_ulp(sock);
+		if (psock_is_smap_sk(sock))
+			tcp_cleanup_ulp(sock);
 		write_lock_bh(&sock->sk_callback_lock);
 		smap_stop_sock(psock, sock);
 		write_unlock_bh(&sock->sk_callback_lock);
@@ -1892,6 +1898,10 @@ static int __sock_map_ctx_update_elem(struct bpf_map *map,
 	 * doesn't update user data.
 	 */
 	if (psock) {
+		if (!psock_is_smap_sk(sock)) {
+			err = -EBUSY;
+			goto out_progs;
+		}
 		if (READ_ONCE(psock->bpf_parse) && parse) {
 			err = -EBUSY;
 			goto out_progs;
Signature · 1 line
2.17.1
#50 lore raw

PATCH 52/76 net: ethernet: cpsw-phy-sel: prefer phandle for phy sel

In reply to Sasha Levin

From: Tony Lindgren <[email protected]>

[ Upstream commit 18eb8aea7fb2fb4490e578b1b8a1096c34b2fc48 ]

The cpsw-phy-sel device is not a child of the cpsw interconnect target module. It lives in the system control module.

Let's fix this issue by trying to use cpsw-phy-sel phandle first if it exists and if not fall back to current usage of trying to find the cpsw-phy-sel child. That way the phy sel driver can be a child of the system control module where it belongs in the device tree.

Without this fix, we cannot have a proper interconnect target module hierarchy in device tree for things like genpd.

Note that deferred probe is mostly not supported by cpsw and this patch does not attempt to fix that. In case deferred probe support is needed, this could be added to cpsw_slave_open() and phy_connect() so they start handling and returning errors.

For documenting it, looks like the cpsw-phy-sel is used for all cpsw device tree nodes. It's missing the related binding documentation, so let's also update the binding documentation accordingly.

Cc Andrew Lunn <[email protected]>
Cc Grygorii Strashko <[email protected]>
Cc Ivan Khoronzhuk <[email protected]>
Cc Mark Rutland <[email protected]>
Cc Murali Karicheri <[email protected]>
Cc Rob Herring <[email protected]>
---
 drivers/net/ethernet/ti/cpsw-phy-sel.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)
drivers/net/ethernet/ti/cpsw-phy-sel.c +6 -3
index 0c1adad7415d..396e1cd10667 100644
@@ -170,10 +170,13 @@ void cpsw_phy_sel(struct device *dev, phy_interface_t phy_mode, int slave)
 	struct device_node *node;
 	struct cpsw_phy_sel_priv *priv;
 
-	node = of_get_child_by_name(dev->of_node, "cpsw-phy-sel");
+	node = of_parse_phandle(dev->of_node, "cpsw-phy-sel", 0);
 	if (!node) {
-		dev_err(dev, "Phy mode driver DT not found\n");
-		return;
+		node = of_get_child_by_name(dev->of_node, "cpsw-phy-sel");
+		if (!node) {
+			dev_err(dev, "Phy mode driver DT not found\n");
+			return;
+		}
 	}
 
 	dev = bus_find_device(&platform_bus_type, NULL, node, match);
Signature · 1 line
2.17.1
#51 lore raw

PATCH 53/76 i2c: uniphier: issue STOP only for last message or I2C_M_STOP

In reply to Sasha Levin

From: Masahiro Yamada <[email protected]>

[ Upstream commit 38f5d8d8cbb2ffa2b54315118185332329ec891c ]

This driver currently emits a STOP if the next message is not I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR ioctl, where read/write transactions are combined without STOP between.

Issue STOP only when the message is the last one _or_ flagged with I2C_M_STOP.

Fixes dd6fd4a32793 ("i2c: uniphier: add UniPhier FIFO-less I2C driver")
---
 drivers/i2c/busses/i2c-uniphier.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)
drivers/i2c/busses/i2c-uniphier.c +2 -5
index bb181b088291..454f914ae66d 100644
@@ -248,11 +248,8 @@ static int uniphier_i2c_master_xfer(struct i2c_adapter *adap,
 		return ret;
 
 	for (msg = msgs; msg < emsg; msg++) {
-		/* If next message is read, skip the stop condition */
-		bool stop = !(msg + 1 < emsg && msg[1].flags & I2C_M_RD);
-		/* but, force it if I2C_M_STOP is set */
-		if (msg->flags & I2C_M_STOP)
-			stop = true;
+		/* Emit STOP if it is the last message or I2C_M_STOP is set. */
+		bool stop = (msg + 1 == emsg) || (msg->flags & I2C_M_STOP);
 
 		ret = uniphier_i2c_master_xfer_one(adap, msg, stop);
 		if (ret)
Signature · 1 line
2.17.1
#52 lore raw

PATCH 54/76 i2c: uniphier-f: issue STOP only for last message or I2C_M_STOP

In reply to Sasha Levin

From: Masahiro Yamada <[email protected]>

[ Upstream commit 4c85609b08c4761eca0a40fd7beb06bc650f252d ]

This driver currently emits a STOP if the next message is not I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR ioctl, where read/write transactions are combined without STOP between.

Issue STOP only when the message is the last one _or_ flagged with I2C_M_STOP.

Fixes 6a62974b667f ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
---
 drivers/i2c/busses/i2c-uniphier-f.c | 7 ++-----
 1 file changed, 2 insertions(+), 5 deletions(-)
drivers/i2c/busses/i2c-uniphier-f.c +2 -5
index 9918bdd81619..a403e8579b65 100644
@@ -401,11 +401,8 @@ static int uniphier_fi2c_master_xfer(struct i2c_adapter *adap,
 		return ret;
 
 	for (msg = msgs; msg < emsg; msg++) {
-		/* If next message is read, skip the stop condition */
-		bool stop = !(msg + 1 < emsg && msg[1].flags & I2C_M_RD);
-		/* but, force it if I2C_M_STOP is set */
-		if (msg->flags & I2C_M_STOP)
-			stop = true;
+		/* Emit STOP if it is the last message or I2C_M_STOP is set. */
+		bool stop = (msg + 1 == emsg) || (msg->flags & I2C_M_STOP);
 
 		ret = uniphier_fi2c_master_xfer_one(adap, msg, stop);
 		if (ret)
Signature · 1 line
2.17.1
#53 lore raw

PATCH 55/76 net: cadence: Fix a sleep-in-atomic-context bug in macb_halt_tx()

In reply to Sasha Levin

From: Jia-Ju Bai <[email protected]>

[ Upstream commit 16fe10cf92783ed9ceb182d6ea2b8adf5e8ec1b8 ]

The kernel module may sleep with holding a spinlock.

The function call paths (from bottom to top) in Linux-4.16 are:

[FUNC] usleep_range drivers/net/ethernet/cadence/macb_main.c, 648:
usleep_range in macb_halt_tx
drivers/net/ethernet/cadence/macb_main.c, 730:
macb_halt_tx in macb_tx_error_task
drivers/net/ethernet/cadence/macb_main.c, 721:
_raw_spin_lock_irqsave in macb_tx_error_task

To fix this bug, usleep_range() is replaced with udelay().

This bug is found by my static analysis tool DSAC.

---
 drivers/net/ethernet/cadence/macb_main.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/cadence/macb_main.c +1 -1
index 515d96e32143..c4d7479938e2 100644
@@ -648,7 +648,7 @@ static int macb_halt_tx(struct macb *bp)
 		if (!(status & MACB_BIT(TGO)))
 			return 0;
 
-		usleep_range(10, 250);
+		udelay(250);
 	} while (time_before(halt_time, timeout));
 
 	return -ETIMEDOUT;
Signature · 1 line
2.17.1
#54 lore raw

PATCH 56/76 fs/cifs: don't translate SFM_SLASH (U+F026) to backslash

In reply to Sasha Levin

From: Jon Kuhn <[email protected]>

[ Upstream commit c15e3f19a6d5c89b1209dc94b40e568177cb0921 ]

When a Mac client saves an item containing a backslash to a file server the backslash is represented in the CIFS/SMB protocol as as U+F026. Before this change, listing a directory containing an item with a backslash in its name will return that item with the backslash represented with a true backslash character (U+005C) because convert_sfm_character mapped U+F026 to U+005C when interpretting the CIFS/SMB protocol response. However, attempting to open or stat the path using a true backslash will result in an error because convert_to_sfm_char does not map U+005C back to U+F026 causing the CIFS/SMB request to be made with the backslash represented as U+005C.

This change simply prevents the U+F026 to U+005C conversion from happenning. This is analogous to how the code does not do any translation of UNI_SLASH (U+F000).

---
 fs/cifs/cifs_unicode.c | 3 ---
 1 file changed, 3 deletions(-)
fs/cifs/cifs_unicode.c +0 -3
index b380e0871372..a2b2355e7f01 100644
@@ -105,9 +105,6 @@ convert_sfm_char(const __u16 src_char, char *target)
 	case SFM_LESSTHAN:
 		*target = '<';
 		break;
-	case SFM_SLASH:
-		*target = '\\';
-		break;
 	case SFM_SPACE:
 		*target = ' ';
 		break;
Signature · 1 line
2.17.1
#55 lore raw

PATCH 57/76 mac80211: fix an off-by-one issue in A-MSDU max_subframe computation

In reply to Sasha Levin

From: Lorenzo Bianconi <[email protected]>

[ Upstream commit 66eb02d839e8495ae6b612e2d09ff599374b80e2 ]

Initialize 'n' to 2 in order to take into account also the first packet in the estimation of max_subframe limit for a given A-MSDU since frag_tail pointer is NULL when ieee80211_amsdu_aggregate routine analyzes the second frame.

Fixes 6e0456b54545 ("mac80211: add A-MSDU tx support")
---
 net/mac80211/tx.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/mac80211/tx.c +1 -1
index 6ca0865de945..9b3b069e418a 100644
@@ -3174,7 +3174,7 @@ static bool ieee80211_amsdu_aggregate(struct ieee80211_sub_if_data *sdata,
 	void *data;
 	bool ret = false;
 	unsigned int orig_len;
-	int n = 1, nfrags, pad = 0;
+	int n = 2, nfrags, pad = 0;
 	u16 hdrlen;
 
 	if (!ieee80211_hw_check(&local->hw, TX_AMSDU))
Signature · 1 line
2.17.1
#56 lore raw

PATCH 58/76 cfg80211: fix a type issue in ieee80211_chandef_to_operating_class()

In reply to Sasha Levin

From: Dan Carpenter <[email protected]>

[ Upstream commit 8442938c3a2177ba16043b3a935f2c78266ad399 ]

The "chandef->center_freq1" variable is a u32 but "freq" is a u16 so we are truncating away the high bits. I noticed this bug because in commit 9cf0a0b4b64a ("cfg80211: Add support for 60GHz band channels 5 and 6") we made "freq <= 56160 + 2160 * 6" a valid requency when before it was only "freq <= 56160 + 2160 * 4" that was valid. It introduces a static checker warning:

    net/wireless/util.c:1571 ieee80211_chandef_to_operating_class()
    warn: always true condition '(freq <= 56160 + 2160 * 6) => (0-u16max <= 69120)'

But really we probably shouldn't have been truncating the high bits away to begin with.

---
 net/wireless/util.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
net/wireless/util.c +1 -1
index 3c654cd7ba56..908bf5b6d89e 100644
@@ -1374,7 +1374,7 @@ bool ieee80211_chandef_to_operating_class(struct cfg80211_chan_def *chandef,
 					  u8 *op_class)
 {
 	u8 vht_opclass;
-	u16 freq = chandef->center_freq1;
+	u32 freq = chandef->center_freq1;
 
 	if (freq >= 2412 && freq <= 2472) {
 		if (chandef->width > NL80211_CHAN_WIDTH_40)
Signature · 1 line
2.17.1
#57 lore raw

PATCH 59/76 mac80211: fix WMM TXOP calculation

In reply to Sasha Levin

From: "Dreyfuss, Haim" <[email protected]>

[ Upstream commit abd76d255d69d70206c01b9cb19ba36a9c1df6a1 ]

In commit 9236c4523e5b ("mac80211: limit wmm params to comply with ETSI requirements"), we have limited the WMM parameters to comply with 802.11 and ETSI standard. Mistakenly the TXOP value was caluclated wrong. Fix it by taking the minimum between 802.11 to ETSI to make sure we are not violating both.

Fixes e552af058148 ("mac80211: limit wmm params to comply with ETSI requirements")
---
 net/mac80211/util.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
net/mac80211/util.c +1 -2
index c80187d6e6bb..93b5bb849ad7 100644
@@ -1151,8 +1151,7 @@ void ieee80211_regulatory_limit_wmm_params(struct ieee80211_sub_if_data *sdata,
 	qparam->cw_min = max_t(u16, qparam->cw_min, wmm_ac->cw_min);
 	qparam->cw_max = max_t(u16, qparam->cw_max, wmm_ac->cw_max);
 	qparam->aifs = max_t(u8, qparam->aifs, wmm_ac->aifsn);
-	qparam->txop = !qparam->txop ? wmm_ac->cot / 32 :
-		min_t(u16, qparam->txop, wmm_ac->cot / 32);
+	qparam->txop = min_t(u16, qparam->txop, wmm_ac->cot / 32);
 	rcu_read_unlock();
 }
 
Signature · 1 line
2.17.1
#58 lore raw

PATCH 60/76 mac80211: fix a race between restart and CSA flows

In reply to Sasha Levin

From: Emmanuel Grumbach <[email protected]>

[ Upstream commit f3ffb6c3a28963657eb8b02a795d75f2ebbd5ef4 ]

We hit a problem with iwlwifi that was caused by a bug in mac80211. A bug in iwlwifi caused the firwmare to crash in certain cases in channel switch. Because of that bug, drv_pre_channel_switch would fail and trigger the restart flow.
Now we had the hw restart worker which runs on the system's workqueue and the csa_connection_drop_work worker that runs on mac80211's workqueue that can run together. This is obviously problematic since the restart work wants to reconfigure the connection, while the csa_connection_drop_work worker does the exact opposite: it tries to disconnect.

Fix this by cancelling the csa_connection_drop_work worker in the restart worker.

Note that this can sound racy: we could have:

driver iface_work CSA_work restart_work
+++++++++++++++++++++++++++++++++++++++++++++

              |
 <--drv_cs ---|
<FW CRASH!>
-CS FAILED-->
              |                       |
              |                 cancel_work(CSA)
           schedule                   |
           CSA work                   |
                         |            |

Race between those 2

But this is not possible because we flush the workqueue in the restart worker before we cancel the CSA worker. That would be bullet proof if we could guarantee that we schedule the CSA worker only from the iface_work which runs on the workqueue (and not on the system's workqueue), but unfortunately we do have an instance in which we schedule the CSA work outside the context of the workqueue (ieee80211_chswitch_done).

Note also that we should probably cancel other workers like beacon_connection_loss_work and possibly others for different types of interfaces, at the very least, IBSS should suffer from the exact same problem, but for now, do the minimum to fix the actual bug that was actually experienced and reproduced.

---
 net/mac80211/main.c | 21 ++++++++++++++++++++-
 1 file changed, 20 insertions(+), 1 deletion(-)
net/mac80211/main.c +20 -1
index 27cd64acaf00..66cbddd65b47 100644
@@ -255,8 +255,27 @@ static void ieee80211_restart_work(struct work_struct *work)
 
 	flush_work(&local->radar_detected_work);
 	rtnl_lock();
-	list_for_each_entry(sdata, &local->interfaces, list)
+	list_for_each_entry(sdata, &local->interfaces, list) {
+		/*
+		 * XXX: there may be more work for other vif types and even
+		 * for station mode: a good thing would be to run most of
+		 * the iface type's dependent _stop (ieee80211_mg_stop,
+		 * ieee80211_ibss_stop) etc...
+		 * For now, fix only the specific bug that was seen: race
+		 * between csa_connection_drop_work and us.
+		 */
+		if (sdata->vif.type == NL80211_IFTYPE_STATION) {
+			/*
+			 * This worker is scheduled from the iface worker that
+			 * runs on mac80211's workqueue, so we can't be
+			 * scheduling this worker after the cancel right here.
+			 * The exception is ieee80211_chswitch_done.
+			 * Then we can have a race...
+			 */
+			cancel_work_sync(&sdata->u.mgd.csa_connection_drop_work);
+		}
 		flush_delayed_work(&sdata->dec_tailroom_needed_wk);
+	}
 	ieee80211_scan_cancel(local);
 
 	/* make sure any new ROC will consider local->in_reconfig */
Signature · 1 line
2.17.1
#59 lore raw

PATCH 61/76 mac80211: Fix station bandwidth setting after channel switch

In reply to Sasha Levin

From: Ilan Peer <[email protected]>

[ Upstream commit 0007e94355fdb71a1cf5dba0754155cba08f0666 ]

When performing a channel switch flow for a managed interface, the flow did not update the bandwidth of the AP station and the rate scale algorithm. In case of a channel width downgrade, this would result with the rate scale algorithm using a bandwidth that does not match the interface channel configuration.

Fix this by updating the AP station bandwidth and rate scaling algorithm before the actual channel change in case of a bandwidth downgrade, or after the actual channel change in case of a bandwidth upgrade.

---
 net/mac80211/mlme.c | 53 +++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)
net/mac80211/mlme.c +53 -0
index a59187c016e0..22b699460176 100644
@@ -978,6 +978,10 @@ static void ieee80211_chswitch_work(struct work_struct *work)
 	 */
 
 	if (sdata->reserved_chanctx) {
+		struct ieee80211_supported_band *sband = NULL;
+		struct sta_info *mgd_sta = NULL;
+		enum ieee80211_sta_rx_bandwidth bw = IEEE80211_STA_RX_BW_20;
+
 		/*
 		 * with multi-vif csa driver may call ieee80211_csa_finish()
 		 * many times while waiting for other interfaces to use their
@@ -986,6 +990,48 @@ static void ieee80211_chswitch_work(struct work_struct *work)
 		if (sdata->reserved_ready)
 			goto out;
 
+		if (sdata->vif.bss_conf.chandef.width !=
+		    sdata->csa_chandef.width) {
+			/*
+			 * For managed interface, we need to also update the AP
+			 * station bandwidth and align the rate scale algorithm
+			 * on the bandwidth change. Here we only consider the
+			 * bandwidth of the new channel definition (as channel
+			 * switch flow does not have the full HT/VHT/HE
+			 * information), assuming that if additional changes are
+			 * required they would be done as part of the processing
+			 * of the next beacon from the AP.
+			 */
+			switch (sdata->csa_chandef.width) {
+			case NL80211_CHAN_WIDTH_20_NOHT:
+			case NL80211_CHAN_WIDTH_20:
+			default:
+				bw = IEEE80211_STA_RX_BW_20;
+				break;
+			case NL80211_CHAN_WIDTH_40:
+				bw = IEEE80211_STA_RX_BW_40;
+				break;
+			case NL80211_CHAN_WIDTH_80:
+				bw = IEEE80211_STA_RX_BW_80;
+				break;
+			case NL80211_CHAN_WIDTH_80P80:
+			case NL80211_CHAN_WIDTH_160:
+				bw = IEEE80211_STA_RX_BW_160;
+				break;
+			}
+
+			mgd_sta = sta_info_get(sdata, ifmgd->bssid);
+			sband =
+				local->hw.wiphy->bands[sdata->csa_chandef.chan->band];
+		}
+
+		if (sdata->vif.bss_conf.chandef.width >
+		    sdata->csa_chandef.width) {
+			mgd_sta->sta.bandwidth = bw;
+			rate_control_rate_update(local, sband, mgd_sta,
+						 IEEE80211_RC_BW_CHANGED);
+		}
+
 		ret = ieee80211_vif_use_reserved_context(sdata);
 		if (ret) {
 			sdata_info(sdata,
@@ -996,6 +1042,13 @@ static void ieee80211_chswitch_work(struct work_struct *work)
 			goto out;
 		}
 
+		if (sdata->vif.bss_conf.chandef.width <
+		    sdata->csa_chandef.width) {
+			mgd_sta->sta.bandwidth = bw;
+			rate_control_rate_update(local, sband, mgd_sta,
+						 IEEE80211_RC_BW_CHANGED);
+		}
+
 		goto out;
 	}
 
Signature · 1 line
2.17.1
#60 lore raw

PATCH 62/76 mac80211: don't Tx a deauth frame if the AP forbade Tx

In reply to Sasha Levin

From: Emmanuel Grumbach <[email protected]>

[ Upstream commit 6c18b27d6e5c6a7206364eae2b47bc8d8b2fa68f ]

If the driver fails to properly prepare for the channel switch, mac80211 will disconnect. If the CSA IE had mode set to 1, it means that the clients are not allowed to send any Tx on the current channel, and that includes the deauthentication frame.

Make sure that we don't send the deauthentication frame in this case.

In iwlwifi, this caused a failure to flush queues since the firmware already closed the queues after having parsed the CSA IE. Then mac80211 would wait until the deauthentication frame would go out (drv_flush(drop=false)) and that would never happen.

---
 net/mac80211/mlme.c | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)
net/mac80211/mlme.c +15 -2
index 22b699460176..b046bf95eb3c 100644
@@ -1270,6 +1270,16 @@ ieee80211_sta_process_chanswitch(struct ieee80211_sub_if_data *sdata,
 					 cbss->beacon_interval));
 	return;
  drop_connection:
+	/*
+	 * This is just so that the disconnect flow will know that
+	 * we were trying to switch channel and failed. In case the
+	 * mode is 1 (we are not allowed to Tx), we will know not to
+	 * send a deauthentication frame. Those two fields will be
+	 * reset when the disconnection worker runs.
+	 */
+	sdata->vif.csa_active = true;
+	sdata->csa_block_tx = csa_ie.mode;
+
 	ieee80211_queue_work(&local->hw, &ifmgd->csa_connection_drop_work);
 	mutex_unlock(&local->chanctx_mtx);
 	mutex_unlock(&local->mtx);
@@ -2453,6 +2463,7 @@ static void __ieee80211_disconnect(struct ieee80211_sub_if_data *sdata)
 	struct ieee80211_local *local = sdata->local;
 	struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
 	u8 frame_buf[IEEE80211_DEAUTH_FRAME_LEN];
+	bool tx;
 
 	sdata_lock(sdata);
 	if (!ifmgd->associated) {
@@ -2460,6 +2471,8 @@ static void __ieee80211_disconnect(struct ieee80211_sub_if_data *sdata)
 		return;
 	}
 
+	tx = !sdata->csa_block_tx;
+
 	/* AP is probably out of range (or not reachable for another reason) so
 	 * remove the bss struct for that AP.
 	 */
@@ -2467,7 +2480,7 @@ static void __ieee80211_disconnect(struct ieee80211_sub_if_data *sdata)
 
 	ieee80211_set_disassoc(sdata, IEEE80211_STYPE_DEAUTH,
 			       WLAN_REASON_DISASSOC_DUE_TO_INACTIVITY,
-			       true, frame_buf);
+			       tx, frame_buf);
 	mutex_lock(&local->mtx);
 	sdata->vif.csa_active = false;
 	ifmgd->csa_waiting_bcn = false;
@@ -2478,7 +2491,7 @@ static void __ieee80211_disconnect(struct ieee80211_sub_if_data *sdata)
 	}
 	mutex_unlock(&local->mtx);
 
-	ieee80211_report_disconnect(sdata, frame_buf, sizeof(frame_buf), true,
+	ieee80211_report_disconnect(sdata, frame_buf, sizeof(frame_buf), tx,
 				    WLAN_REASON_DISASSOC_DUE_TO_INACTIVITY);
 
 	sdata_unlock(sdata);
Signature · 1 line
2.17.1
#61 lore raw

PATCH 63/76 mac80211: shorten the IBSS debug messages

In reply to Sasha Levin

From: Emmanuel Grumbach <[email protected]>

[ Upstream commit c6e57b3896fc76299913b8cfd82d853bee8a2c84 ]

When tracing is enabled, all the debug messages are recorded and must not exceed MAX_MSG_LEN (100) columns. Longer debug messages grant the user with:

WARNING: CPU: 3 PID: 32642 at /tmp/wifi-core-20180806094828/src/iwlwifi-stack-dev/net/mac80211/./trace_msg.h:32 trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Workqueue: phy1 ieee80211_iface_work [mac80211]
 RIP: 0010:trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
 Call Trace:
  __sdata_dbg+0xbd/0x120 [mac80211]
  ieee80211_ibss_rx_queued_mgmt+0x15f/0x510 [mac80211]
  ieee80211_iface_work+0x21d/0x320 [mac80211]
---
 net/mac80211/ibss.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)
net/mac80211/ibss.c +11 -11
index 6449a1c2283b..f0f5fedb8caa 100644
@@ -947,8 +947,8 @@ static void ieee80211_rx_mgmt_deauth_ibss(struct ieee80211_sub_if_data *sdata,
 	if (len < IEEE80211_DEAUTH_FRAME_LEN)
 		return;
 
-	ibss_dbg(sdata, "RX DeAuth SA=%pM DA=%pM BSSID=%pM (reason: %d)\n",
-		 mgmt->sa, mgmt->da, mgmt->bssid, reason);
+	ibss_dbg(sdata, "RX DeAuth SA=%pM DA=%pM\n", mgmt->sa, mgmt->da);
+	ibss_dbg(sdata, "\tBSSID=%pM (reason: %d)\n", mgmt->bssid, reason);
 	sta_info_destroy_addr(sdata, mgmt->sa);
 }
 
@@ -966,9 +966,9 @@ static void ieee80211_rx_mgmt_auth_ibss(struct ieee80211_sub_if_data *sdata,
 	auth_alg = le16_to_cpu(mgmt->u.auth.auth_alg);
 	auth_transaction = le16_to_cpu(mgmt->u.auth.auth_transaction);
 
-	ibss_dbg(sdata,
-		 "RX Auth SA=%pM DA=%pM BSSID=%pM (auth_transaction=%d)\n",
-		 mgmt->sa, mgmt->da, mgmt->bssid, auth_transaction);
+	ibss_dbg(sdata, "RX Auth SA=%pM DA=%pM\n", mgmt->sa, mgmt->da);
+	ibss_dbg(sdata, "\tBSSID=%pM (auth_transaction=%d)\n",
+		 mgmt->bssid, auth_transaction);
 
 	if (auth_alg != WLAN_AUTH_OPEN || auth_transaction != 1)
 		return;
@@ -1175,10 +1175,10 @@ static void ieee80211_rx_bss_info(struct ieee80211_sub_if_data *sdata,
 		rx_timestamp = drv_get_tsf(local, sdata);
 	}
 
-	ibss_dbg(sdata,
-		 "RX beacon SA=%pM BSSID=%pM TSF=0x%llx BCN=0x%llx diff=%lld @%lu\n",
+	ibss_dbg(sdata, "RX beacon SA=%pM BSSID=%pM TSF=0x%llx\n",
 		 mgmt->sa, mgmt->bssid,
-		 (unsigned long long)rx_timestamp,
+		 (unsigned long long)rx_timestamp);
+	ibss_dbg(sdata, "\tBCN=0x%llx diff=%lld @%lu\n",
 		 (unsigned long long)beacon_timestamp,
 		 (unsigned long long)(rx_timestamp - beacon_timestamp),
 		 jiffies);
@@ -1537,9 +1537,9 @@ static void ieee80211_rx_mgmt_probe_req(struct ieee80211_sub_if_data *sdata,
 
 	tx_last_beacon = drv_tx_last_beacon(local);
 
-	ibss_dbg(sdata,
-		 "RX ProbeReq SA=%pM DA=%pM BSSID=%pM (tx_last_beacon=%d)\n",
-		 mgmt->sa, mgmt->da, mgmt->bssid, tx_last_beacon);
+	ibss_dbg(sdata, "RX ProbeReq SA=%pM DA=%pM\n", mgmt->sa, mgmt->da);
+	ibss_dbg(sdata, "\tBSSID=%pM (tx_last_beacon=%d)\n",
+		 mgmt->bssid, tx_last_beacon);
 
 	if (!tx_last_beacon && is_multicast_ether_addr(mgmt->da))
 		return;
Signature · 1 line
2.17.1
#62 lore raw

PATCH 64/76 fsnotify: fix ignore mask logic in fsnotify()

In reply to Sasha Levin

From: Amir Goldstein <[email protected]>

[ Upstream commit 9bdda4e9cf2dcecb60a0683b10ffb8cd7e5f2f45 ]

Commit 92183a42898d ("fsnotify: fix ignore mask logic in send_to_group()") acknoledges the use case of ignoring an event on an inode mark, because of an ignore mask on a mount mark of the same group (i.e. I want to get all events on this file, except for the events that came from that mount).

This change depends on correctly merging the inode marks and mount marks group lists, so that the mount mark ignore mask would be tested in send_to_group(). Alas, the merging of the lists did not take into account the case where event in question is not in the mask of any of the mount marks.

To fix this, completely remove the tests for inode and mount event masks from the lists merging code.

Fixes 92183a42898d ("fsnotify: fix ignore mask logic in send_to_group")
---
 fs/notify/fsnotify.c | 13 +++----------
 1 file changed, 3 insertions(+), 10 deletions(-)
fs/notify/fsnotify.c +3 -10
index f174397b63a0..ababdbfab537 100644
@@ -351,16 +351,9 @@ int fsnotify(struct inode *to_tell, __u32 mask, const void *data, int data_is,
 
 	iter_info.srcu_idx = srcu_read_lock(&fsnotify_mark_srcu);
 
-	if ((mask & FS_MODIFY) ||
-	    (test_mask & to_tell->i_fsnotify_mask)) {
-		iter_info.marks[FSNOTIFY_OBJ_TYPE_INODE] =
-			fsnotify_first_mark(&to_tell->i_fsnotify_marks);
-	}
-
-	if (mnt && ((mask & FS_MODIFY) ||
-		    (test_mask & mnt->mnt_fsnotify_mask))) {
-		iter_info.marks[FSNOTIFY_OBJ_TYPE_INODE] =
-			fsnotify_first_mark(&to_tell->i_fsnotify_marks);
+	iter_info.marks[FSNOTIFY_OBJ_TYPE_INODE] =
+		fsnotify_first_mark(&to_tell->i_fsnotify_marks);
+	if (mnt) {
 		iter_info.marks[FSNOTIFY_OBJ_TYPE_VFSMOUNT] =
 			fsnotify_first_mark(&mnt->mnt_fsnotify_marks);
 	}
Signature · 1 line
2.17.1
#63 lore raw

PATCH 65/76 net/ibm/emac: wrong emac_calc_base call was used by typo

In reply to Sasha Levin

From: Ivan Mikhaylov <[email protected]>

[ Upstream commit bf68066fccb10fce6bbffdda24ee2ae314c9c5b2 ]

__emac_calc_base_mr1 was used instead of __emac4_calc_base_mr1 by copy-paste mistake for emac4syn.

Fixes 45d6e545505fd32edb812f085be7de45b6a5c0af ("net/ibm/emac: add 8192 rx/tx fifo size")
---
 drivers/net/ethernet/ibm/emac/core.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/net/ethernet/ibm/emac/core.c +3 -3
index 354c0982847b..372664686309 100644
@@ -494,9 +494,6 @@ static u32 __emac_calc_base_mr1(struct emac_instance *dev, int tx_size, int rx_s
 	case 16384:
 		ret |= EMAC_MR1_RFS_16K;
 		break;
-	case 8192:
-		ret |= EMAC4_MR1_RFS_8K;
-		break;
 	case 4096:
 		ret |= EMAC_MR1_RFS_4K;
 		break;
@@ -537,6 +534,9 @@ static u32 __emac4_calc_base_mr1(struct emac_instance *dev, int tx_size, int rx_
 	case 16384:
 		ret |= EMAC4_MR1_RFS_16K;
 		break;
+	case 8192:
+		ret |= EMAC4_MR1_RFS_8K;
+		break;
 	case 4096:
 		ret |= EMAC4_MR1_RFS_4K;
 		break;
Signature · 1 line
2.17.1
#64 lore raw

PATCH 66/76 nds32: fix logic for module

In reply to Sasha Levin

From: Greentime Hu <[email protected]>

[ Upstream commit 1dfdf99106668679b0de5a62fd4f42c1a11c9445 ]

This bug is report by Dan Carpenter. We shall use ~loc_mask instead of !loc_mask because we need to and(&) the bits of ~loc_mask.

Fixes c9a4a8da6baa ("nds32: Loadable modules")
---
 arch/nds32/kernel/module.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/nds32/kernel/module.c +2 -2
index 4167283d8293..1e31829cbc2a 100644
@@ -40,7 +40,7 @@ void do_reloc16(unsigned int val, unsigned int *loc, unsigned int val_mask,
 
 	tmp2 = tmp & loc_mask;
 	if (partial_in_place) {
-		tmp &= (!loc_mask);
+		tmp &= (~loc_mask);
 		tmp =
 		    tmp2 | ((tmp + ((val & val_mask) >> val_shift)) & val_mask);
 	} else {
@@ -70,7 +70,7 @@ void do_reloc32(unsigned int val, unsigned int *loc, unsigned int val_mask,
 
 	tmp2 = tmp & loc_mask;
 	if (partial_in_place) {
-		tmp &= (!loc_mask);
+		tmp &= (~loc_mask);
 		tmp =
 		    tmp2 | ((tmp + ((val & val_mask) >> val_shift)) & val_mask);
 	} else {
Signature · 1 line
2.17.1
#65 lore raw

PATCH 67/76 nds32: add NULL entry to the end of_device_id array

In reply to Sasha Levin

From: YueHaibing <[email protected]>

[ Upstream commit 1944a50859ec2b570b42b459ac25d607fc7c31f0 ]

Make sure of_device_id tables are NULL terminated. Found by coccinelle spatch "misc/of_table.cocci"

---
 arch/nds32/kernel/atl2c.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
arch/nds32/kernel/atl2c.c +2 -1
index 0c6d031a1c4a..0c5386e72098 100644
@@ -9,7 +9,8 @@
 
 void __iomem *atl2c_base;
 static const struct of_device_id atl2c_ids[] __initconst = {
-	{.compatible = "andestech,atl2c",}
+	{.compatible = "andestech,atl2c",},
+	{}
 };
 
 static int __init atl2c_of_init(void)
Signature · 1 line
2.17.1
#66 lore raw

PATCH 68/76 nds32: Fix empty call trace

In reply to Sasha Levin

From: Zong Li <[email protected]>

[ Upstream commit c17df7960534357fb74074c2f514c831d4a9cf5a ]

The compiler predefined macro 'NDS32_ABI_2' had been removed, it should use the '__NDS32_ABI_2' here.

---
 arch/nds32/kernel/traps.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/nds32/kernel/traps.c +1 -1
index a6205fd4db52..f0e974347c26 100644
@@ -137,7 +137,7 @@ static void __dump(struct task_struct *tsk, unsigned long *base_reg)
 		       !((unsigned long)base_reg & 0x3) &&
 		       ((unsigned long)base_reg >= TASK_SIZE)) {
 			unsigned long next_fp;
-#if !defined(NDS32_ABI_2)
+#if !defined(__NDS32_ABI_2)
 			ret_addr = base_reg[0];
 			next_fp = base_reg[1];
 #else
Signature · 1 line
2.17.1
#67 lore raw

PATCH 69/76 nds32: Fix get_user/put_user macro expand pointer problem

In reply to Sasha Levin

From: Zong Li <[email protected]>

[ Upstream commit 6cce95a6c7d288ac2126eee4b95df448b9015b84 ]

The pointer argument of macro need to be taken out once first, and then use the new pointer in the macro body.

In kernel/trace/trace.c, get_user(ch, ubuf++) causes the unexpected increment after expand the macro.

---
 arch/nds32/include/asm/uaccess.h | 26 ++++++++++++++------------
 1 file changed, 14 insertions(+), 12 deletions(-)
arch/nds32/include/asm/uaccess.h +14 -12
index 18a009f3804d..3f771e0595e8 100644
@@ -78,8 +78,9 @@ static inline void set_fs(mm_segment_t fs)
 #define get_user(x,p)							\
 ({									\
 	long __e = -EFAULT;						\
-	if(likely(access_ok(VERIFY_READ,  p, sizeof(*p)))) {		\
-		__e = __get_user(x,p);					\
+	const __typeof__(*(p)) __user *__p = (p);			\
+	if(likely(access_ok(VERIFY_READ, __p, sizeof(*__p)))) {		\
+		__e = __get_user(x, __p);				\
 	} else								\
 		x = 0;							\
 	__e;								\
@@ -99,10 +100,10 @@ static inline void set_fs(mm_segment_t fs)
 
 #define __get_user_err(x,ptr,err)					\
 do {									\
-	unsigned long __gu_addr = (unsigned long)(ptr);			\
+	const __typeof__(*(ptr)) __user *__gu_addr = (ptr);		\
 	unsigned long __gu_val;						\
-	__chk_user_ptr(ptr);						\
-	switch (sizeof(*(ptr))) {					\
+	__chk_user_ptr(__gu_addr);					\
+	switch (sizeof(*(__gu_addr))) {					\
 	case 1:								\
 		__get_user_asm("lbi",__gu_val,__gu_addr,err);		\
 		break;							\
@@ -119,7 +120,7 @@ do {									\
 		BUILD_BUG(); 						\
 		break;							\
 	}								\
-	(x) = (__typeof__(*(ptr)))__gu_val;				\
+	(x) = (__typeof__(*(__gu_addr)))__gu_val;			\
 } while (0)
 
 #define __get_user_asm(inst,x,addr,err)					\
@@ -169,8 +170,9 @@ do {									\
 #define put_user(x,p)							\
 ({									\
 	long __e = -EFAULT;						\
-	if(likely(access_ok(VERIFY_WRITE,  p, sizeof(*p)))) {		\
-		__e = __put_user(x,p);					\
+	__typeof__(*(p)) __user *__p = (p);				\
+	if(likely(access_ok(VERIFY_WRITE, __p, sizeof(*__p)))) {	\
+		__e = __put_user(x, __p);				\
 	}								\
 	__e;								\
 })
@@ -189,10 +191,10 @@ do {									\
 
 #define __put_user_err(x,ptr,err)					\
 do {									\
-	unsigned long __pu_addr = (unsigned long)(ptr);			\
-	__typeof__(*(ptr)) __pu_val = (x);				\
-	__chk_user_ptr(ptr);						\
-	switch (sizeof(*(ptr))) {					\
+	__typeof__(*(ptr)) __user *__pu_addr = (ptr);			\
+	__typeof__(*(__pu_addr)) __pu_val = (x);			\
+	__chk_user_ptr(__pu_addr);					\
+	switch (sizeof(*(__pu_addr))) {					\
 	case 1:								\
 		__put_user_asm("sbi",__pu_val,__pu_addr,err);		\
 		break;							\
Signature · 1 line
2.17.1
#68 lore raw

PATCH 70/76 nds32: fix build error because of wrong semicolon

In reply to Sasha Levin

From: Greentime Hu <[email protected]>

[ Upstream commit ec865393292f5ad8d52da20788b3685ebce44c48 ]

It shall be removed in the define usage. We shall not put a semicolon there.

/kisskb/src/arch/nds32/include/asm/elf.h:126:29: error: expected '}' before ';' token

 #define ELF_DATA ELFDATA2LSB;
                             ^
/kisskb/src/fs/proc/kcore.c:318:17: note: in expansion of macro 'ELF_DATA'
     [EI_DATA] = ELF_DATA,
                 ^~~~~~~~
/kisskb/src/fs/proc/kcore.c:312:15: note: to match this '{'
    .e_ident = {
               ^

/kisskb/src/scripts/Makefile.build:307: recipe for target 'fs/proc/kcore.o' failed

---
 arch/nds32/include/asm/elf.h | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
arch/nds32/include/asm/elf.h +2 -2
index 56c479058802..f5f9cf7e0544 100644
@@ -121,9 +121,9 @@ struct elf32_hdr;
  */
 #define ELF_CLASS	ELFCLASS32
 #ifdef __NDS32_EB__
-#define ELF_DATA	ELFDATA2MSB;
+#define ELF_DATA	ELFDATA2MSB
 #else
-#define ELF_DATA	ELFDATA2LSB;
+#define ELF_DATA	ELFDATA2LSB
 #endif
 #define ELF_ARCH	EM_NDS32
 #define USE_ELF_CORE_DUMP
Signature · 1 line
2.17.1
#69 lore raw

PATCH 71/76 tools/vm/slabinfo.c: fix sign-compare warning

In reply to Sasha Levin

From: Naoya Horiguchi <[email protected]>

[ Upstream commit 904506562e0856f2535d876407d087c9459d345b ]

Currently we get the following compiler warning:

    slabinfo.c:854:22: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
       if (s->object_size < min_objsize)
                          ^

due to the mismatch of signed/unsigned comparison. ->object_size and ->slab_size are never expected to be negative, so let's define them as unsigned int.

---
 tools/vm/slabinfo.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
tools/vm/slabinfo.c +2 -2
index f82c2eaa859d..334b16db0ebb 100644
@@ -30,8 +30,8 @@ struct slabinfo {
 	int alias;
 	int refs;
 	int aliases, align, cache_dma, cpu_slabs, destroy_by_rcu;
-	int hwcache_align, object_size, objs_per_slab;
-	int sanity_checks, slab_size, store_user, trace;
+	unsigned int hwcache_align, object_size, objs_per_slab;
+	unsigned int sanity_checks, slab_size, store_user, trace;
 	int order, poison, reclaim_account, red_zone;
 	unsigned long partial, objects, slabs, objects_partial, objects_total;
 	unsigned long alloc_fastpath, alloc_slowpath;
Signature · 1 line
2.17.1
#70 lore raw

PATCH 72/76 tools/vm/page-types.c: fix "defined but not used" warning

In reply to Sasha Levin

From: Naoya Horiguchi <[email protected]>

[ Upstream commit 7ab660f8baecfe26c1c267fa8e64d2073feae2bb ]

debugfs_known_mountpoints[] is not used any more, so let's remove it.

---
 tools/vm/page-types.c | 6 ------
 1 file changed, 6 deletions(-)
tools/vm/page-types.c +0 -6
index cce853dca691..a4c31fb2887b 100644
@@ -156,12 +156,6 @@ static const char * const page_flag_names[] = {
 };
 
 
-static const char * const debugfs_known_mountpoints[] = {
-	"/sys/kernel/debug",
-	"/debug",
-	0,
-};
-
 /*
  * data structures
  */
Signature · 1 line
2.17.1
#71 lore raw

PATCH 73/76 nds32: linker script: GCOV kernel may refers data in __exit

In reply to Sasha Levin

From: Greentime Hu <[email protected]>

[ Upstream commit 3350139c0ff3c95724b784f7109987d533cb3ecd ]

This patch is used to fix nds32 allmodconfig/allyesconfig build error because GCOV kernel embeds counters in the kernel for each line and a part of that embed in __exit text. So we need to keep the EXIT_TEXT and EXIT_DATA if CONFIG_GCOV_KERNEL=y.

---
 arch/nds32/kernel/vmlinux.lds.S | 12 ++++++++++++
 1 file changed, 12 insertions(+)
arch/nds32/kernel/vmlinux.lds.S +12 -0
index 288313b886ef..9e90f30a181d 100644
@@ -13,14 +13,26 @@ OUTPUT_ARCH(nds32)
 ENTRY(_stext_lma)
 jiffies = jiffies_64;
 
+#if defined(CONFIG_GCOV_KERNEL)
+#define NDS32_EXIT_KEEP(x)	x
+#else
+#define NDS32_EXIT_KEEP(x)
+#endif
+
 SECTIONS
 {
 	_stext_lma = TEXTADDR - LOAD_OFFSET;
 	. = TEXTADDR;
 	__init_begin = .;
 	HEAD_TEXT_SECTION
+	.exit.text : {
+		NDS32_EXIT_KEEP(EXIT_TEXT)
+	}
 	INIT_TEXT_SECTION(PAGE_SIZE)
 	INIT_DATA_SECTION(16)
+	.exit.data : {
+		NDS32_EXIT_KEEP(EXIT_DATA)
+	}
 	PERCPU_SECTION(L1_CACHE_BYTES)
 	__init_end = .;
 
Signature · 1 line
2.17.1
#72 lore raw

PATCH 74/76 ceph: avoid a use-after-free in ceph_destroy_options()

In reply to Sasha Levin

From: Ilya Dryomov <[email protected]>

[ Upstream commit 8aaff15168cfbc7c8980fdb0e8a585f1afe56ec0 ]

syzbot reported a use-after-free in ceph_destroy_options(), called from ceph_mount(). The problem was that create_fs_client() consumed the opt pointer on some errors, but not on all of them. Make sure it always consumes both libceph and ceph options.

---
 fs/ceph/super.c | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)
fs/ceph/super.c +11 -5
index 95a3b3ac9b6e..60f81ac369b5 100644
@@ -603,6 +603,8 @@ static int extra_mon_dispatch(struct ceph_client *client, struct ceph_msg *msg)
 
 /*
  * create a new fs client
+ *
+ * Success or not, this function consumes @fsopt and @opt.
  */
 static struct ceph_fs_client *create_fs_client(struct ceph_mount_options *fsopt,
 					struct ceph_options *opt)
@@ -610,17 +612,20 @@ static struct ceph_fs_client *create_fs_client(struct ceph_mount_options *fsopt,
 	struct ceph_fs_client *fsc;
 	int page_count;
 	size_t size;
-	int err = -ENOMEM;
+	int err;
 
 	fsc = kzalloc(sizeof(*fsc), GFP_KERNEL);
-	if (!fsc)
-		return ERR_PTR(-ENOMEM);
+	if (!fsc) {
+		err = -ENOMEM;
+		goto fail;
+	}
 
 	fsc->client = ceph_create_client(opt, fsc);
 	if (IS_ERR(fsc->client)) {
 		err = PTR_ERR(fsc->client);
 		goto fail;
 	}
+	opt = NULL; /* fsc->client now owns this */
 
 	fsc->client->extra_mon_dispatch = extra_mon_dispatch;
 	fsc->client->osdc.abort_on_full = true;
@@ -678,6 +683,9 @@ static struct ceph_fs_client *create_fs_client(struct ceph_mount_options *fsopt,
 	ceph_destroy_client(fsc->client);
 fail:
 	kfree(fsc);
+	if (opt)
+		ceph_destroy_options(opt);
+	destroy_mount_options(fsopt);
 	return ERR_PTR(err);
 }
 
@@ -1042,8 +1050,6 @@ static struct dentry *ceph_mount(struct file_system_type *fs_type,
 	fsc = create_fs_client(fsopt, opt);
 	if (IS_ERR(fsc)) {
 		res = ERR_CAST(fsc);
-		destroy_mount_options(fsopt);
-		ceph_destroy_options(opt);
 		goto out_final;
 	}
 
Signature · 1 line
2.17.1
#73 lore raw

PATCH 75/76 firmware: arm_scmi: fix divide by zero when sustained_perf_level is zero

In reply to Sasha Levin

From: Sudeep Holla <[email protected]>

[ Upstream commit 96d529bac562574600eda85726fcfa3eef6dde8e ]

Firmware can provide zero as values for sustained performance level and corresponding sustained frequency in kHz in order to hide the actual frequencies and provide only abstract values. It may endup with divide by zero scenario resulting in kernel panic.

Let's set the multiplication factor to one if either one or both of them (sustained_perf_level and sustained_freq) are set to zero.

Fixes a9e3fbfaa0ff ("firmware: arm_scmi: add initial support for performance protocol")
---
 drivers/firmware/arm_scmi/perf.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
drivers/firmware/arm_scmi/perf.c +7 -1
index 2a219b1261b1..49cb74f54a10 100644
@@ -166,7 +166,13 @@ scmi_perf_domain_attributes_get(const struct scmi_handle *handle, u32 domain,
 					le32_to_cpu(attr->sustained_freq_khz);
 		dom_info->sustained_perf_level =
 					le32_to_cpu(attr->sustained_perf_level);
-		dom_info->mult_factor =	(dom_info->sustained_freq_khz * 1000) /
+		if (!dom_info->sustained_freq_khz ||
+		    !dom_info->sustained_perf_level)
+			/* CPUFreq converts to kHz, hence default 1000 */
+			dom_info->mult_factor =	1000;
+		else
+			dom_info->mult_factor =
+					(dom_info->sustained_freq_khz * 1000) /
 					dom_info->sustained_perf_level;
 		memcpy(dom_info->name, attr->name, SCMI_MAX_STR_SIZE);
 	}
Signature · 1 line
2.17.1
#74 lore raw

PATCH 76/76 afs: Fix cell specification to permit an empty address list

In reply to Sasha Levin

From: David Howells <[email protected]>

[ Upstream commit ecfe951f0c1b169ea4b7dd6f3a404dfedd795bc2 ]

Fix the cell specification mechanism to allow cells to be pre-created without having to specify at least one address (the addresses will be upcalled for).

This allows the cell information preload service to avoid the need to issue loads of DNS lookups during boot to get the addresses for each cell (500+ lookups for the 'standard' cell list[*]). The lookups can be done later as each cell is accessed through the filesystem.

Also remove the print statement that prints a line every time a new cell is added.

[*] There are 144 cells in the list. Each cell is first looked up for an
SRV record, and if that fails, for an AFSDB record. These get a list of server names, each of which then has to be looked up to get the addresses for that server. E.g.:

dig srv _afs3-vlserver._udp.grand.central.org

---
 fs/afs/proc.c | 15 +++++++--------
 1 file changed, 7 insertions(+), 8 deletions(-)
fs/afs/proc.c +7 -8
index 0c3285c8db95..476dcbb79713 100644
@@ -98,13 +98,13 @@ static int afs_proc_cells_write(struct file *file, char *buf, size_t size)
 		goto inval;
 
 	args = strchr(name, ' ');
-	if (!args)
-		goto inval;
-	do {
-		*args++ = 0;
-	} while(*args == ' ');
-	if (!*args)
-		goto inval;
+	if (args) {
+		do {
+			*args++ = 0;
+		} while(*args == ' ');
+		if (!*args)
+			goto inval;
+	}
 
 	/* determine command to perform */
 	_debug("cmd=%s name=%s args=%s", buf, name, args);
@@ -120,7 +120,6 @@ static int afs_proc_cells_write(struct file *file, char *buf, size_t size)
 
 		if (test_and_set_bit(AFS_CELL_FL_NO_GC, &cell->flags))
 			afs_put_cell(net, cell);
-		printk("kAFS: Added new cell '%s'\n", name);
 	} else {
 		goto inval;
 	}
Signature · 1 line
2.17.1