Skip to contentSkip to conversation

nvme: call nvme_complete_rq on NVME_MPATH failures

PATCH New James Smart 5 participants 5 messages Sep 27, 2018 – Sep 30, 2018 NVMe

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 nvme: call nvme_complete_rq on NVME_MPATH failures

When an io is rejected by nvmf_check_ready() due to validation of the controller state, the nvmf_fail_nonready_command() will normally return BLK_STS_RESOURCE to requeue and retry. However, if the controller is dying or the io is marked for NVME multipath, the io is failed so that the controller can terminate or so that the io can be issued on a different path. Unfortunately, as this reject point is before the transport has accepted the command, blk-mq ends up completing the io and never calls nvme_complete_rq(), which is where multipath may preserve/re-route the io. The end result is, the device user ends up seeing an EIO error.

Example: single path connectivity, controller is under load, and a reset is induced. An i/o is received: a) while the reset state has been set but the queues have yet to be stopped; or b) after queues are started (at end of reset) but before the reconnect has completed. The io finishes with an EIO status.

This patch makes the following changes:
- Adds the HOST_PATH_ERROR pathing status from TP4028
- Modifies the reject point such that it appears to queue successfully, but actually completes the io with the new pathing status and calls nvme_complete_rq().
- nvme_complete_rq() recognizes the new status, avoids resetting the controller (likely was already done in order to get this new status), and calls the multipather to clear the current path that errored. This allows the next command (retry or new command) to select a new path if there is one.

Signed-off-by James Smart <jsmart2021 at gmail.com>
---
 drivers/nvme/host/fabrics.c   | 7 +++++--
 drivers/nvme/host/multipath.c | 7 +++++++
 include/linux/nvme.h          | 1 +
 3 files changed, 13 insertions(+), 2 deletions(-)
drivers/nvme/host/fabrics.c +5 -2
index 206d63cb1afc..bcd09d3a44da 100644
@@ -552,8 +552,11 @@ blk_status_t nvmf_fail_nonready_command(struct nvme_ctrl *ctrl,
 	    ctrl->state != NVME_CTRL_DEAD &&
 	    !blk_noretry_request(rq) && !(rq->cmd_flags & REQ_NVME_MPATH))
 		return BLK_STS_RESOURCE;
-	nvme_req(rq)->status = NVME_SC_ABORT_REQ;
-	return BLK_STS_IOERR;
+
+	nvme_req(rq)->status = NVME_SC_HOST_PATH_ERROR;
+	blk_mq_start_request(rq);
+	nvme_complete_rq(rq);
+	return BLK_STS_OK;
 }
 EXPORT_SYMBOL_GPL(nvmf_fail_nonready_command);
 
drivers/nvme/host/multipath.c +7 -0
index 5a9562881d4e..b285648c3a7f 100644
@@ -77,6 +77,13 @@ void nvme_failover_req(struct request *req)
 			queue_work(nvme_wq, &ns->ctrl->ana_work);
 		}
 		break;
+	case NVME_SC_HOST_PATH_ERROR:
+		/*
+		 * Temporary transport disruption in talking to the controller.
+		 * Try to send on a new path.
+		 */
+		nvme_mpath_clear_current_path(ns);
+		break;
 	default:
 		/*
 		 * Reset the controller for any non-ANA error as we don't know
include/linux/nvme.h +1 -0
index 68e91ef5494c..818dbe9331be 100644
@@ -1241,6 +1241,7 @@ enum {
 	NVME_SC_ANA_PERSISTENT_LOSS	= 0x301,
 	NVME_SC_ANA_INACCESSIBLE	= 0x302,
 	NVME_SC_ANA_TRANSITION		= 0x303,
+	NVME_SC_HOST_PATH_ERROR		= 0x370,
 
 	NVME_SC_DNR			= 0x4000,
 };
Signature · 1 line
2.13.1
maintainer
#1 lore raw

PATCH v2 1/1 nvme: call nvme_complete_rq on NVME_MPATH failures

Quoted 6 lines
drivers/nvme/host/fabrics.c +0 -0
index 206d63cb1afc..bcd09d3a44da 100644

drivers/nvme/host/fabrics.c blk_status_t nvmf_fail_nonready_command(struct nvme_ctrl *ctrl, · line 557

Quoted 8 lines
drivers/nvme/host/fabrics.c +3 -2
@@ -552,8 +552,11 @@ blk_status_t nvmf_fail_nonready_command(struct nvme_ctrl *ctrl,
  	    ctrl->state != NVME_CTRL_DEAD &&
  	    !blk_noretry_request(rq) && !(rq->cmd_flags & REQ_NVME_MPATH))
  		return BLK_STS_RESOURCE;
-	nvme_req(rq)->status = NVME_SC_ABORT_REQ;
-	return BLK_STS_IOERR;
+
+	nvme_req(rq)->status = NVME_SC_HOST_PATH_ERROR;
+	blk_mq_start_request(rq);

Might be worth a comment here on why we don't call nvme_end_request

drivers/nvme/host/fabrics.c blk_status_t nvmf_fail_nonready_command(struct nvme_ctrl *ctrl, · line 562

Quoted 5 lines
drivers/nvme/host/fabrics.c +2 -0
+	nvme_complete_rq(rq);
+	return BLK_STS_OK;
  }
  EXPORT_SYMBOL_GPL(nvmf_fail_nonready_command);
 

Other than than, looks good,

Reviewed-by Sagi Grimberg <sagi at grimberg.me>
#3 lore raw

PATCH v2 1/1 nvme: call nvme_complete_rq on NVME_MPATH failures

In reply to James Smart
Quoted 77 lines · James Smart

When an io is rejected by nvmf_check_ready() due to validation of the controller state, the nvmf_fail_nonready_command() will normally return BLK_STS_RESOURCE to requeue and retry. However, if the controller is dying or the io is marked for NVME multipath, the io is failed so that the controller can terminate or so that the io can be issued on a different path. Unfortunately, as this reject point is before the transport has accepted the command, blk-mq ends up completing the io and never calls nvme_complete_rq(), which is where multipath may preserve/re-route the io. The end result is, the device user ends up seeing an EIO error.

Example: single path connectivity, controller is under load, and a reset is induced. An i/o is received: a) while the reset state has been set but the queues have yet to be stopped; or b) after queues are started (at end of reset) but before the reconnect has completed. The io finishes with an EIO status.

This patch makes the following changes:
- Adds the HOST_PATH_ERROR pathing status from TP4028
- Modifies the reject point such that it appears to queue successfully, but actually completes the io with the new pathing status and calls nvme_complete_rq().
- nvme_complete_rq() recognizes the new status, avoids resetting the controller (likely was already done in order to get this new status), and calls the multipather to clear the current path that errored. This allows the next command (retry or new command) to select a new path if there is one.

Signed-off-by James Smart <jsmart2021 at gmail.com>
---
 drivers/nvme/host/fabrics.c   | 7 +++++--
 drivers/nvme/host/multipath.c | 7 +++++++
 include/linux/nvme.h          | 1 +
 3 files changed, 13 insertions(+), 2 deletions(-)
drivers/nvme/host/fabrics.c +5 -2
index 206d63cb1afc..bcd09d3a44da 100644
@@ -552,8 +552,11 @@ blk_status_t nvmf_fail_nonready_command(struct nvme_ctrl *ctrl,
 	    ctrl->state != NVME_CTRL_DEAD &&
 	    !blk_noretry_request(rq) && !(rq->cmd_flags & REQ_NVME_MPATH))
 		return BLK_STS_RESOURCE;
-	nvme_req(rq)->status = NVME_SC_ABORT_REQ;
-	return BLK_STS_IOERR;
+
+	nvme_req(rq)->status = NVME_SC_HOST_PATH_ERROR;
+	blk_mq_start_request(rq);
+	nvme_complete_rq(rq);
+	return BLK_STS_OK;
 }
 EXPORT_SYMBOL_GPL(nvmf_fail_nonready_command);
 
drivers/nvme/host/multipath.c +7 -0
index 5a9562881d4e..b285648c3a7f 100644
@@ -77,6 +77,13 @@ void nvme_failover_req(struct request *req)
 			queue_work(nvme_wq, &ns->ctrl->ana_work);
 		}
 		break;
+	case NVME_SC_HOST_PATH_ERROR:
+		/*
+		 * Temporary transport disruption in talking to the controller.
+		 * Try to send on a new path.
+		 */
+		nvme_mpath_clear_current_path(ns);
+		break;
 	default:
 		/*
 		 * Reset the controller for any non-ANA error as we don't know
include/linux/nvme.h +0 -0
index 68e91ef5494c..818dbe9331be 100644

include/linux/nvme.h enum { · line 1247

Quoted 7 lines
include/linux/nvme.h +1 -0
@@ -1241,6 +1241,7 @@ enum {
 	NVME_SC_ANA_PERSISTENT_LOSS	= 0x301,
 	NVME_SC_ANA_INACCESSIBLE	= 0x302,
 	NVME_SC_ANA_TRANSITION		= 0x303,
+	NVME_SC_HOST_PATH_ERROR		= 0x370,
 
 	NVME_SC_DNR			= 0x4000,
 };

Don't we need a mapping in nvme_error_status() to map the new code into a BLK_STS_XXX code other that BLK_STS_IOERR?

Cheers,

Hannes

Signature · 5 lines
Dr. Hannes Reinecke		   Teamlead Storage & Networking
hare at suse.de			               +49 911 74053 688
SUSE LINUX GmbH, Maxfeldstr. 5, 90409 N?rnberg
GF: F. Imend?rffer, J. Smithard, J. Guild, D. Upmanyu, G. Norton
HRB 21284 (AG N?rnberg)
#4 lore raw

PATCH v2 1/1 nvme: call nvme_complete_rq on NVME_MPATH failures

Quoted 2 lines · Hannes Reinecke

Don't we need a mapping in nvme_error_status() to map the new code into a BLK_STS_XXX code other that BLK_STS_IOERR?

Under what condition and for what reason ?

IOERR is appropriate, and what it was reporting before (for NVME_SC_ABORT_REQ).
If it's for a NVME_MPATH io, it doesn't matter as the status is ignored due to the retry.

-- james