hwmon: (adm1275): Add device tree param for shunt resistor
Subsystems (3)
PATCH v2 1/1 hwmon: (adm1275): Add device tree param for shunt resistor
The ADM series of hotswap controllers support extending the current measurement range by using a sensing resistor value other than the typical 1 mOhm. For example, using a 0.5 mOhm sensing resistor doubles the maximal current can be measured.
Current driver assumes a shunt resistor value of 1 mOhm in calculation, meaning for other resistor values, hwmon will report scaled current/power measurements. This patch adds a device tree parameter so that individual boards can configure its shunt resistor value.
--- .../devicetree/bindings/hwmon/adm1275.txt | 25 +++++++++++++++++++ Documentation/hwmon/adm1275 | 3 +++ drivers/hwmon/pmbus/adm1275.c | 15 +++++++++-- 3 files changed, 41 insertions(+), 2 deletions(-) create mode 100644 Documentation/devicetree/bindings/hwmon/adm1275.txt
Documentation/devicetree/bindings/hwmon/adm1275.txt new file +25 -0
@@ -0,0 +1,25 @@ +adm1275 properties + +Required properties: +- compatible: Must be one of the supported compatible strings: + - "adi,adm1075" for adm1075 + - "adi,adm1272" for adm1272 + - "adi,adm1275" for adm1275 + - "adi,adm1276" for adm1276 + - "adi,adm1278" for adm1278 + - "adi,adm1293" for adm1293 + - "adi,adm1294" for adm1294 +- reg: I2C address + +Optional properties: + +- shunt-resistor-micro-ohms + Shunt resistor value in micro-Ohm + +Example: + +adm1272@10 { + compatible = "adi,adm1272"; + reg = <0x10>; + shunt-resistor-micro-ohms = <500>; +};
Documentation/hwmon/adm1275 +3 -0
@@ -58,6 +58,9 @@ The ADM1075, unlike many other PMBus devices, does not support internal voltage or current scaling. Reported voltages, currents, and power are raw measurements, and will typically have to be scaled. +The shunt value in micro-ohms can be set via device tree at compile-time. Please +refer to the Documentation/devicetree/bindings/hwmon/adm1275.txt for bindings +if the device tree is used. Platform data support ---------------------
drivers/hwmon/pmbus/adm1275.c +13 -2
@@ -373,6 +373,7 @@ static int adm1275_probe(struct i2c_client *client,const struct coefficients *coefficients;int vindex =-1 , voindex =-1 , cindex =-1 , pindex =-1 ;int tindex =-1 ; +u32 shunt; if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_READ_BYTE_DATA
@@ -421,6 +422,13 @@ static int adm1275_probe(struct i2c_client *client,if (!data)return -ENOMEM ; +if (of_property_read_u32 (client->dev.of_node, +"shunt-resistor-micro-ohms" , &shunt)) + shunt =1000 ;/* 1 mOhm if not set via DT */ + +if (shunt ==0 ) +return -EINVAL ; + data->id = mid->driver_data; info = &data->info;
@@ -654,12 +662,15 @@ static int adm1275_probe(struct i2c_client *client, info->R[PSC_VOLTAGE_OUT ] = coefficients[voindex].R; }if (cindex >=0 ) { - info->m[PSC_CURRENT_OUT ] = coefficients[cindex].m; +/* Scale current with sense resistor value */ + info->m[PSC_CURRENT_OUT ] = + coefficients[cindex].m * shunt /1000 ; info->b[PSC_CURRENT_OUT ] = coefficients[cindex].b; info->R[PSC_CURRENT_OUT ] = coefficients[cindex].R; }if (pindex >=0 ) { - info->m[PSC_POWER ] = coefficients[pindex].m; + info->m[PSC_POWER ] = + coefficients[pindex].m * shunt /1000 ; info->b[PSC_POWER ] = coefficients[pindex].b; info->R[PSC_POWER ] = coefficients[pindex].R; }
Signature · 1 line
2.19.0.605.g01d371f741-goog
Rob Herring
maintainerQuoted 5 lines · Kun Yi
The ADM series of hotswap controllers support extending the current measurement range by using a sensing resistor value other than the typical 1 mOhm. For example, using a 0.5 mOhm sensing resistor doubles the maximal current can be measured.
Quoted 8 lines
Current driver assumes a shunt resistor value of 1 mOhm in calculation, meaning for other resistor values, hwmon will report scaled current/power measurements. This patch adds a device tree parameter so that individual boards can configure its shunt resistor value.
Signed-off-by Kun Yi <[email protected]>--- .../devicetree/bindings/hwmon/adm1275.txt | 25 +++++++++++++++++++
This should be a separate patch. In particular, the subject doesn't really reflect that you are adding a new binding.
Otherwise, the binding looks fine.
Quoted 4 lines
Documentation/hwmon/adm1275 | 3 +++ drivers/hwmon/pmbus/adm1275.c | 15 +++++++++-- 3 files changed, 41 insertions(+), 2 deletions(-) create mode 100644 Documentation/devicetree/bindings/hwmon/adm1275.txt