drm/i915/psr: Share PSR and PSR2 exit mask
Subsystems (2)
PATCH v4 1/7 drm/i915/psr: Share PSR and PSR2 exit mask
Now both PSR and PSR2 have the same exit mask, so let's share then instead of have the same code 2 times.
--- drivers/gpu/drm/i915/intel_psr.c | 34 ++++++++++++-------------------- 1 file changed, 13 insertions(+), 21 deletions(-)
drivers/gpu/drm/i915/intel_psr.c +13 -21
@@ -580,28 +580,20 @@ static void intel_psr_enable_source(struct intel_dp *intel_dp,else chicken &= ~VSC_DATA_SEL_SOFTWARE_CONTROL ;I915_WRITE (CHICKEN_TRANS (cpu_transcoder), chicken); - -I915_WRITE (EDP_PSR_DEBUG , -EDP_PSR_DEBUG_MASK_MEMUP | -EDP_PSR_DEBUG_MASK_HPD | -EDP_PSR_DEBUG_MASK_LPSP | -EDP_PSR_DEBUG_MASK_MAX_SLEEP | -EDP_PSR_DEBUG_MASK_DISP_REG_WRITE ); - }else { -/* -* Per Spec: Avoid continuous PSR exit by masking MEMUP -* and HPD. also mask LPSP to avoid dependency on other -* drivers that might block runtime_pm besides -* preventing other hw tracking issues now we can rely -* on frontbuffer tracking. -*/ -I915_WRITE (EDP_PSR_DEBUG , -EDP_PSR_DEBUG_MASK_MEMUP | -EDP_PSR_DEBUG_MASK_HPD | -EDP_PSR_DEBUG_MASK_LPSP | -EDP_PSR_DEBUG_MASK_DISP_REG_WRITE | -EDP_PSR_DEBUG_MASK_MAX_SLEEP ); } + +/* +* Per Spec: Avoid continuous PSR exit by masking MEMUP and HPD also +* mask LPSP to avoid dependency on other drivers that might block +* runtime_pm besides preventing other hw tracking issues now we +* can rely on frontbuffer tracking. +*/ +I915_WRITE (EDP_PSR_DEBUG , +EDP_PSR_DEBUG_MASK_MEMUP | +EDP_PSR_DEBUG_MASK_HPD | +EDP_PSR_DEBUG_MASK_LPSP | +EDP_PSR_DEBUG_MASK_DISP_REG_WRITE | +EDP_PSR_DEBUG_MASK_MAX_SLEEP ); } static void intel_psr_enable_locked(struct drm_i915_private *dev_priv,
Signature · 6 lines
2.19.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v4 2/7 drm/i915/psr: Make MASK_DISP_REG_WRITE reserved in PSR_MASK for ICL
ICL spec states that this bit is now reserved.
Bspec: 7722
v2(Dhinakaran and Jani):
- instead of remove bit in gen11 now only setting if if gen < 11
- changed commit title
--- drivers/gpu/drm/i915/i915_reg.h | 4 ++-- drivers/gpu/drm/i915/intel_psr.c | 16 ++++++++++------ 2 files changed, 12 insertions(+), 8 deletions(-)
drivers/gpu/drm/i915/i915_reg.h +2 -2
@@ -4195,7 +4195,7 @@ enum {#define EDP_PSR_DEBUG_MASK_LPSP (1 << 27)#define EDP_PSR_DEBUG_MASK_MEMUP (1 << 26)#define EDP_PSR_DEBUG_MASK_HPD (1 << 25) -#define EDP_PSR_DEBUG_MASK_DISP_REG_WRITE (1 << 16) +#define EDP_PSR_DEBUG_MASK_DISP_REG_WRITE (1 << 16)/* Reserved in ICL+ */ #define EDP_PSR_DEBUG_EXIT_ON_PIXEL_UNDERRUN (1 << 15)/* SKL+ */ #define EDP_PSR2_CTL _MMIO(0x6f900)
@@ -4232,7 +4232,7 @@ enum {#define PSR_EVENT_FRONT_BUFFER_MODIFY (1 << 9)#define PSR_EVENT_WD_TIMER_EXPIRE (1 << 8)#define PSR_EVENT_PIPE_REGISTERS_UPDATE (1 << 6) -#define PSR_EVENT_REGISTER_UPDATE (1 << 5) +#define PSR_EVENT_REGISTER_UPDATE (1 << 5)/* Reserved in ICL+ */ #define PSR_EVENT_HDCP_ENABLE (1 << 4)#define PSR_EVENT_KVMR_SESSION_ENABLE (1 << 3)#define PSR_EVENT_VBI_ENABLE (1 << 2)
drivers/gpu/drm/i915/intel_psr.c +10 -6
@@ -563,6 +563,7 @@ static void intel_psr_enable_source(struct intel_dp *intel_dp, {struct drm_i915_private *dev_priv =dp_to_i915 (intel_dp);enum transcoder cpu_transcoder = crtc_state->cpu_transcoder; +u32 mask;/* Only HSW and BDW have PSR AUX registers that need to be setup. SKL+ * use hardcoded values PSR AUX transactions
@@ -588,12 +589,15 @@ static void intel_psr_enable_source(struct intel_dp *intel_dp,* runtime_pm besides preventing other hw tracking issues now we * can rely on frontbuffer tracking. */ -I915_WRITE (EDP_PSR_DEBUG , -EDP_PSR_DEBUG_MASK_MEMUP | -EDP_PSR_DEBUG_MASK_HPD | -EDP_PSR_DEBUG_MASK_LPSP | -EDP_PSR_DEBUG_MASK_DISP_REG_WRITE | -EDP_PSR_DEBUG_MASK_MAX_SLEEP ); + mask =EDP_PSR_DEBUG_MASK_MEMUP | +EDP_PSR_DEBUG_MASK_HPD | +EDP_PSR_DEBUG_MASK_LPSP | +EDP_PSR_DEBUG_MASK_MAX_SLEEP ; + +if (INTEL_GEN (dev_priv) <11 ) + mask |=EDP_PSR_DEBUG_MASK_DISP_REG_WRITE ; + +I915_WRITE (EDP_PSR_DEBUG , mask); } static void intel_psr_enable_locked(struct drm_i915_private *dev_priv,
Signature · 6 lines
2.19.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v4 3/7 drm/i915/psr: Remove PSR2 TODO error handling
In reply to José Roberto de SouzaWe are already handling all PSR2 errors, so we can drop this TODO.
--- drivers/gpu/drm/i915/intel_psr.c | 2 -- 1 file changed, 2 deletions(-)
drivers/gpu/drm/i915/intel_psr.c +0 -2
@@ -1128,8 +1128,6 @@ void intel_psr_short_pulse(struct intel_dp *intel_dp)intel_psr_disable_locked (intel_dp);/* clear status register */ drm_dp_dpcd_writeb (&intel_dp->aux,DP_PSR_ERROR_STATUS , val); - -/* TODO: handle PSR2 errors */ exit:mutex_unlock (&psr->lock); }
Signature · 6 lines
2.19.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v4 4/7 drm/i915/psr: Use WA to force HW tracking to exit PSR2
In reply to José Roberto de SouzaThis WA also works fine for PSR2, triggering a selective update when possible.
--- drivers/gpu/drm/i915/intel_psr.c | 24 ++++++++++-------------- 1 file changed, 10 insertions(+), 14 deletions(-)
drivers/gpu/drm/i915/intel_psr.c +10 -14
@@ -1027,20 +1027,16 @@ void intel_psr_flush(struct drm_i915_private *dev_priv,/* By definition flush = invalidate + flush */ if (frontbuffer_bits) { -if (dev_priv->psr.psr2_enabled) { -intel_psr_exit (dev_priv); - }else { -/* -* Display WA #0884: all -* This documented WA for bxt can be safely applied -* broadly so we can force HW tracking to exit PSR -* instead of disabling and re-enabling. -* Workaround tells us to write 0 to CUR_SURFLIVE_A, -* but it makes more sense write to the current active -* pipe. -*/ -I915_WRITE (CURSURFLIVE (pipe),0 ); - } +/* +* Display WA #0884: all +* This documented WA for bxt can be safely applied +* broadly so we can force HW tracking to exit PSR +* instead of disabling and re-enabling. +* Workaround tells us to write 0 to CUR_SURFLIVE_A, +* but it makes more sense write to the current active +* pipe. +*/ +I915_WRITE (CURSURFLIVE (pipe),0 ); }if (!dev_priv->psr.active && !dev_priv->psr.busy_frontbuffer_bits)
Signature · 6 lines
2.19.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v4 5/7 drm/i915/psr: Remove main link standby mode from debugfs
In reply to José Roberto de SouzaMain link stand by is only valid for PSR1 as it is not possible to enable PSR2 and keep main link on but even for PSR1 it is not useful information and it can be removed without any drawbacks. But if someone still wants to check that this patch is providing the full PSR_CTL register value so user can check if bit 27 is set, this will also expose more information about how PSR1 and PSR2 was configured in source.
--- drivers/gpu/drm/i915/i915_debugfs.c | 25 ++++++++++++------------- 1 file changed, 12 insertions(+), 13 deletions(-)
drivers/gpu/drm/i915/i915_debugfs.c +12 -13
@@ -2712,8 +2712,8 @@ psr_source_status(struct drm_i915_private *dev_priv, struct seq_file *m)static int i915_edp_psr_status (struct seq_file *m,void *data) {struct drm_i915_private *dev_priv =node_to_i915 (m->private); -u32 psrperf =0 ; -bool enabled = false; +u32 val; +bool enabled;bool sink_support;if (!HAS_PSR (dev_priv))
@@ -2733,24 +2733,23 @@ static int i915_edp_psr_status(struct seq_file *m, void *data)seq_printf (m,"Busy frontbuffer bits: 0x%03x\n" , dev_priv->psr.busy_frontbuffer_bits); -if (dev_priv->psr.psr2_enabled) - enabled =I915_READ (EDP_PSR2_CTL ) &EDP_PSR2_ENABLE ; -else - enabled =I915_READ (EDP_PSR_CTL ) &EDP_PSR_ENABLE ; - -seq_printf (m,"Main link in standby mode: %s\n" , -yesno (dev_priv->psr.link_standby)); +if (dev_priv->psr.psr2_enabled) { + val =I915_READ (EDP_PSR2_CTL ); + enabled = val &EDP_PSR2_ENABLE ; + }else { + val =I915_READ (EDP_PSR_CTL ); + enabled = val &EDP_PSR_ENABLE ; + } -seq_printf (m,"HW Enabled & Active bit: %s\n" ,yesno (enabled)); +seq_printf (m,"HW enabled: %s [0x%x]\n" ,yesno (enabled), val);/* * SKL+ Perf counter is reset to 0 everytime DC state is entered */ if (IS_HASWELL (dev_priv) ||IS_BROADWELL (dev_priv)) { - psrperf =I915_READ (EDP_PSR_PERF_CNT ) & -EDP_PSR_PERF_CNT_MASK ; + val =I915_READ (EDP_PSR_PERF_CNT ) &EDP_PSR_PERF_CNT_MASK ; -seq_printf (m,"Performance_Counter: %u\n" , psrperf); +seq_printf (m,"Performance_Counter: %u\n" , val); }psr_source_status (dev_priv, m);
Signature · 6 lines
2.19.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH v4 5/7] drm/i915/psr: Remove main link standby mode from debugfs
Quoted 7 lines · PDT José Roberto de Souza
Main link stand by is only valid for PSR1 as it is not possible to enable PSR2 and keep main link on but even for PSR1 it is not useful information and it can be removed without any drawbacks. But if someone still wants to check that this patch is providing the full
PSR_CTLregister value so user can check if bit 27 is set, this will also expose more information about how PSR1 and PSR2 was configured in source.
Yes, knowing the full configuration (idle frames, training pattern ) is very useful for debug.
Quoted 36 lines
Cc Dhinakaran Pandiyan <[email protected]>Suggested-by Dhinakaran Pandiyan <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/i915_debugfs.c | 25 ++++++++++++------------- 1 file changed, 12 insertions(+), 13 deletions(-)(quoted diff) +0
-0
b/drivers/gpu/drm/i915/i915_debugfs.cindexf42e93b71e67..48e65becd035100644drivers/gpu/drm/i915/i915_debugfs.c +0
-0@@ -2712,8 +2712,8 @@ psr_source_status(struct drm_i915_private *dev_priv,struct
seq_file*m) static inti915_edp_psr_status(struct seq_file *m, void *data)
{drivers/gpu/drm/i915/i915_debugfs.c +2
-9struct drm_i915_private *dev_priv =node_to_i915 (m->private); -u32 psrperf =0 ; -bool enabled = false; +u32 val; +bool enabled;bool sink_support;if (!HAS_PSR (dev_priv))@@ -2733,24 +2733,23 @@ static int i915_edp_psr_status(struct seq_file *m, void *data) seq_printf(m, "Busy frontbuffer bits: 0x%03x\n", dev_priv->psr.busy_frontbuffer_bits); -if (dev_priv->psr.psr2_enabled) - enabled =I915_READ (EDP_PSR2_CTL ) &EDP_PSR2_ENABLE ; -else - enabled =I915_READ (EDP_PSR_CTL ) &EDP_PSR_ENABLE ; - -seq_printf (m,"Main link in standby mode: %s\n" , -yesno (dev_priv->psr.link_standby));
drivers/gpu/drm/i915/i915_debugfs.c static int i915_edp_psr_status(struct seq_file *m, · line 2744
Quoted 10 lines
drivers/gpu/drm/i915/i915_debugfs.c +8
-1+if (dev_priv->psr.psr2_enabled) { + val =I915_READ (EDP_PSR2_CTL ); + enabled = val &EDP_PSR2_ENABLE ; + }else { + val =I915_READ (EDP_PSR_CTL ); + enabled = val &EDP_PSR_ENABLE ; + } -seq_printf (m,"HW Enabled & Active bit: %s\n" ,yesno (enabled)); +seq_printf (m,"HW enabled: %s [0x%x]\n" ,yesno (enabled), val);
The status register is printed as <hex reg value>[<mapped string>]. Can we please keep this interface consistent? Also, this change will need changes in IGTs.
With the print format changed
Quoted 4 lines
drivers/gpu/drm/i915/i915_debugfs.c +0
-0/* * SKL+ Perf counter is reset to 0 everytime DC state is entered */
drivers/gpu/drm/i915/i915_debugfs.c static int i915_edp_psr_status(struct seq_file *m, void *data) · line 2755
Quoted 10 lines
drivers/gpu/drm/i915/i915_debugfs.c +2
-3if (IS_HASWELL (dev_priv) ||IS_BROADWELL (dev_priv)) { - psrperf =I915_READ (EDP_PSR_PERF_CNT ) & -EDP_PSR_PERF_CNT_MASK ; + val =I915_READ (EDP_PSR_PERF_CNT ) &EDP_PSR_PERF_CNT_MASK ; -seq_printf (m,"Performance_Counter: %u\n" , psrperf); +seq_printf (m,"Performance_Counter: %u\n" , val); }psr_source_status (dev_priv, m);
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v4 6/7 drm/i915/psr: Don't tell sink that main link will be active while is active PSR2
In reply to José Roberto de SouzaFor PSR2 there is no register to tell HW to keep main link enabled while PSR2 is active, so don't configure sink DPCD with a wrong value.
v4: rebased on top of the patch removing link standby from debugfs
--- drivers/gpu/drm/i915/intel_psr.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/intel_psr.c +6 -4
@@ -346,12 +346,14 @@ static void intel_psr_enable_sink(struct intel_dp *intel_dp)drm_dp_dpcd_writeb (&intel_dp->aux,DP_RECEIVER_ALPM_CONFIG ,DP_ALPM_ENABLE ); dpcd_val |=DP_PSR_ENABLE_PSR2 ; + }else { +if (dev_priv->psr.link_standby) + dpcd_val |=DP_PSR_MAIN_LINK_ACTIVE ; + +if (INTEL_GEN (dev_priv) >=8 ) + dpcd_val |=DP_PSR_CRC_VERIFICATION ; } -if (dev_priv->psr.link_standby) - dpcd_val |=DP_PSR_MAIN_LINK_ACTIVE ; -if (!dev_priv->psr.psr2_enabled &&INTEL_GEN (dev_priv) >=8 ) - dpcd_val |=DP_PSR_CRC_VERIFICATION ;drm_dp_dpcd_writeb (&intel_dp->aux,DP_PSR_EN_CFG , dpcd_val);drm_dp_dpcd_writeb (&intel_dp->aux,DP_SET_POWER ,DP_SET_POWER_D0 );
Signature · 6 lines
2.19.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Re: [PATCH v4 6/7] drm/i915/psr: Don't tell sink that main link will be active while is active PSR2
Quoted 5 lines · PDT José Roberto de Souza
For PSR2 there is no register to tell HW to keep main link enabled while PSR2 is active, so don't configure sink DPCD with a wrong value.
v4: rebased on top of the patch removing link standby from debugfs
Quoted 20 lines
Cc Dhinakaran Pandiyan <[email protected]>Signed-off-by José Roberto de Souza <[email protected]>--- drivers/gpu/drm/i915/intel_psr.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-)(quoted diff) +0
-0
b/drivers/gpu/drm/i915/intel_psr.cindex423cdf84059c..26317a4e03d2100644drivers/gpu/drm/i915/intel_psr.c +5
-0@@ -346,12 +346,14 @@ static void intel_psr_enable_sink(struct intel_dp *intel_dp) drm_dp_dpcd_writeb(&intel_dp->aux, DP_RECEIVER_ALPM_CONFIG,DP_ALPM_ENABLE ); dpcd_val |=DP_PSR_ENABLE_PSR2 ; + }else { +if (dev_priv->psr.link_standby) + dpcd_val |=DP_PSR_MAIN_LINK_ACTIVE ; + +if (INTEL_GEN (dev_priv) >=8 )
drivers/gpu/drm/i915/intel_psr.c static void intel_psr_enable_sink(struct intel_dp · line 359
Quoted 10 lines
drivers/gpu/drm/i915/intel_psr.c +1
-4+ dpcd_val |=DP_PSR_CRC_VERIFICATION ; } -if (dev_priv->psr.link_standby) - dpcd_val |=DP_PSR_MAIN_LINK_ACTIVE ; -if (!dev_priv->psr.psr2_enabled &&INTEL_GEN (dev_priv) >=8 ) - dpcd_val |=DP_PSR_CRC_VERIFICATION ;drm_dp_dpcd_writeb (&intel_dp->aux,DP_PSR_EN_CFG , dpcd_val);drm_dp_dpcd_writeb (&intel_dp->aux,DP_SET_POWER ,DP_SET_POWER_D0 );
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
PATCH v4 7/7 drm/i915/psr: Remove alpm from i915_psr
In reply to José Roberto de SouzaALPM is a requirement and we don't need to keep it's cached, what were done in commit 97c9de66ca80
("drm/i915/psr: Fix ALPM cap check for PSR2") but the alpm was not removed from i915_psr.
--- drivers/gpu/drm/i915/i915_drv.h | 1 - 1 file changed, 1 deletion(-)
drivers/gpu/drm/i915/i915_drv.h +0 -1
@@ -634,7 +634,6 @@ struct i915_psr {bool sink_psr2_support;bool link_standby;bool colorimetry_support; -bool alpm;bool psr2_enabled;u8 sink_sync_latency;ktime_t last_entry_attempt;
Signature · 6 lines
2.19.0 _______________________________________________ Intel-gfx mailing list [email protected] https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✗ Fi.CI.SPARSE: warning for series starting with [v4,1/7] drm/i915/psr: Share PSR and PSR2 exit mask
In reply to José Roberto de Souza== Series Details ==
== Series Details ==
Series: series starting with [v4,1/7] drm/i915/psr: Share PSR and PSR2 exit mask
URL : https://patchwork.freedesktop.org/series/50526/
State : warning
== Summary ==
$ dim sparse origin/drm-tip Commit: drm/i915/psr: Share PSR and PSR2 exit mask Okay!
Commit: drm/i915/psr: Make MASK_DISP_REG_WRITE reserved in PSR_MASK for ICL Okay!
Commit: drm/i915/psr: Remove PSR2 TODO error handling Okay!
Commit: drm/i915/psr: Use WA to force HW tracking to exit PSR2 Okay!
Commit: drm/i915/psr: Remove main link standby mode from debugfs Okay!
Commit: drm/i915/psr: Don't tell sink that main link will be active while is active PSR2 Okay!
Commit: drm/i915/psr: Remove alpm from i915_psr -drivers/gpu/drm/i915/selftests/../i915_drv.h:3726:16: warning: expression using sizeof(void) +drivers/gpu/drm/i915/selftests/../i915_drv.h:3725:16: warning: expression using sizeof(void)
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.BAT: success for series starting with [v4,1/7] drm/i915/psr: Share PSR and PSR2 exit mask
In reply to José Roberto de Souza== Series Details ==
== Series Details ==
Series: series starting with [v4,1/7] drm/i915/psr: Share PSR and PSR2 exit mask
URL : https://patchwork.freedesktop.org/series/50526/
State : success
== Summary ==
= CI Bug Log - changes from CI_DRM_4925 -> Patchwork_10351 =
== Summary - SUCCESS ==
No regressions found.
External URL: https://patchwork.freedesktop.org/api/1.0/series/50526/revisions/1/mbox/
== Known issues ==
Here are the changes found in Patchwork_10351 that come from known issues:
=== IGT changes ===
==== Issues hit ====
igt@gem_ctx_switch@basic-default-heavy:
fi-glk-j4005: PASS -> DMESG-WARN (fdo#105719)
igt@gem_exec_suspend@basic-s4-devices:
fi-blb-e6850: PASS -> INCOMPLETE (fdo#107718)
igt@kms_pipe_crc_basic@suspend-read-crc-pipe-b:
fi-byt-clapper: PASS -> FAIL (fdo#107362, fdo#103191)
igt@kms_psr@cursor_plane_move:
fi-kbl-r: PASS -> FAIL (fdo#107383) +3
fi-whl-u: PASS -> FAIL (fdo#107383) +3
igt@kms_psr@primary_mmap_gtt:
fi-kbl-7560u: NOTRUN -> FAIL (fdo#107383) +3
fi-cnl-u: PASS -> FAIL (fdo#107383) +3
igt@kms_psr@primary_page_flip:
fi-skl-6600u: PASS -> FAIL (fdo#107383) +3
==== Possible fixes ====
igt@kms_flip@basic-flip-vs-modeset:
fi-glk-j4005: DMESG-WARN (fdo#106000) -> PASS
igt@kms_flip@basic-plain-flip:
fi-glk-j4005: DMESG-WARN (fdo#106097) -> PASS
igt@kms_pipe_crc_basic@suspend-read-crc-pipe-a:
fi-byt-clapper: FAIL (fdo#107362, fdo#103191) -> PASS fdo#103191 https://bugs.freedesktop.org/show_bug.cgi?id=103191
fdo#105719 https://bugs.freedesktop.org/show_bug.cgi?id=105719
fdo#106000 https://bugs.freedesktop.org/show_bug.cgi?id=106000
fdo#106097 https://bugs.freedesktop.org/show_bug.cgi?id=106097
fdo#107362 https://bugs.freedesktop.org/show_bug.cgi?id=107362
fdo#107383 https://bugs.freedesktop.org/show_bug.cgi?id=107383
fdo#107718 https://bugs.freedesktop.org/show_bug.cgi?id=107718
== Participating hosts (48 -> 38) ==
Additional (1): fi-kbl-7560u
Missing (11): fi-ilk-m540 fi-hsw-4200u fi-skl-6770hq fi-skl-guc fi-byt-squawks fi-icl-u2 fi-bsw-cyan fi-ctg-p8600 fi-cfl-s3 fi-icl-u fi-skl-6700hq
== Build changes ==
* Linux: CI_DRM_4925 -> Patchwork_10351
CI_DRM_4925: b652f33e63e1aafb7fc1cb2a9648a14d66f0d35f @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4665: 267870165d9ef66b4ab423e4efe7bacba023d75e @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_10351: 514e604a2b9a7a2422d760c87651585b6896a1c5 @ git://anongit.freedesktop.org/gfx-ci/linux
== Linux commits ==
514e604a2b9a drm/i915/psr: Remove alpm from i915_psr665311b03a29 drm/i915/psr: Don't tell sink that main link will be active while is active PSR2 1537843c8c69 drm/i915/psr: Remove main link standby mode from debugfs bfceeb76d06e drm/i915/psr: Use WA to force HW tracking to exit PSR2 5fa7ea20efba drm/i915/psr: Remove PSR2 TODO error handling357c03ffd698 drm/i915/psr: Make MASK_DISP_REG_WRITE reserved in PSR_MASK for ICL f91c986fb9b7 drm/i915/psr: Share PSR and PSR2 exit mask
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10351/issues.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Patchwork
CI✓ Fi.CI.IGT: success for series starting with [v4,1/7] drm/i915/psr: Share PSR and PSR2 exit mask
In reply to José Roberto de Souza== Series Details ==
== Series Details ==
Series: series starting with [v4,1/7] drm/i915/psr: Share PSR and PSR2 exit mask
URL : https://patchwork.freedesktop.org/series/50526/
State : success
== Summary ==
= CI Bug Log - changes from CI_DRM_4925_full -> Patchwork_10351_full =
== Summary - SUCCESS ==
No regressions found.
== Known issues ==
Here are the changes found in Patchwork_10351_full that come from known issues:
=== IGT changes ===
==== Issues hit ====
igt@drv_suspend@shrink:
shard-apl: PASS -> INCOMPLETE (fdo#106886, fdo#103927)
igt@gem_ppgtt@blt-vs-render-ctx0:
shard-skl: NOTRUN -> TIMEOUT (fdo#108039, fdo#108130)
igt@kms_available_modes_crc@available_mode_test_crc:
shard-skl: NOTRUN -> FAIL (fdo#106641)
igt@kms_busy@extended-pageflip-modeset-hang-oldfb-render-b:
shard-skl: NOTRUN -> DMESG-WARN (fdo#107956)
igt@kms_cursor_crc@cursor-128x42-sliding:
shard-apl: PASS -> FAIL (fdo#103232) +2
igt@kms_cursor_crc@cursor-64x64-suspend:
shard-apl: PASS -> FAIL (fdo#103232, fdo#103191)
igt@kms_fbcon_fbt@psr-suspend:
shard-skl: NOTRUN -> FAIL (fdo#103833)
igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-fullscreen:
shard-apl: PASS -> FAIL (fdo#103167)
igt@kms_frontbuffer_tracking@fbc-1p-rte:
shard-apl: PASS -> FAIL (fdo#105682, fdo#103167)
igt@kms_frontbuffer_tracking@fbcpsr-1p-offscren-pri-indfb-draw-mmap-cpu:
shard-skl: PASS -> FAIL (fdo#107719) +43
igt@kms_frontbuffer_tracking@fbcpsr-1p-rte:
shard-skl: NOTRUN -> FAIL (fdo#105682, fdo#107719)
igt@kms_frontbuffer_tracking@fbcpsr-rgb565-draw-render:
shard-skl: SKIP -> FAIL (fdo#107719)
igt@kms_frontbuffer_tracking@psr-1p-primscrn-indfb-pgflip-blt:
shard-skl: NOTRUN -> FAIL (fdo#107719) +19
{igt@kms_plane_alpha_blend@pipe-c-constant-alpha-min}:
shard-skl: NOTRUN -> FAIL (fdo#108145) +1
igt@kms_plane_multiple@atomic-pipe-a-tiling-y:
shard-apl: PASS -> FAIL (fdo#103166) +1
igt@kms_psr@cursor_mmap_cpu:
shard-skl: PASS -> FAIL (fdo#107383) +4
igt@kms_psr@sprite_blt:
shard-skl: NOTRUN -> FAIL (fdo#107383) +3
igt@kms_setmode@basic:
shard-snb: NOTRUN -> FAIL (fdo#99912)
igt@kms_sysfs_edid_timing:
shard-skl: NOTRUN -> FAIL (fdo#100047)
==== Possible fixes ====
igt@kms_plane@plane-panning-bottom-right-suspend-pipe-c-planes:
shard-kbl: INCOMPLETE (fdo#103665) -> PASS
igt@kms_setmode@basic:
shard-apl: FAIL (fdo#99912) -> PASS
shard-kbl: FAIL (fdo#99912) -> PASS
igt@kms_universal_plane@universal-plane-pipe-a-functional:
shard-apl: FAIL (fdo#103166) -> PASS {name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).
fdo#100047 https://bugs.freedesktop.org/show_bug.cgi?id=100047
fdo#103166 https://bugs.freedesktop.org/show_bug.cgi?id=103166
fdo#103167 https://bugs.freedesktop.org/show_bug.cgi?id=103167
fdo#103191 https://bugs.freedesktop.org/show_bug.cgi?id=103191
fdo#103232 https://bugs.freedesktop.org/show_bug.cgi?id=103232
fdo#103665 https://bugs.freedesktop.org/show_bug.cgi?id=103665
fdo#103833 https://bugs.freedesktop.org/show_bug.cgi?id=103833
fdo#103927 https://bugs.freedesktop.org/show_bug.cgi?id=103927
fdo#105682 https://bugs.freedesktop.org/show_bug.cgi?id=105682
fdo#106641 https://bugs.freedesktop.org/show_bug.cgi?id=106641
fdo#106886 https://bugs.freedesktop.org/show_bug.cgi?id=106886
fdo#107383 https://bugs.freedesktop.org/show_bug.cgi?id=107383
fdo#107719 https://bugs.freedesktop.org/show_bug.cgi?id=107719
fdo#107956 https://bugs.freedesktop.org/show_bug.cgi?id=107956
fdo#108039 https://bugs.freedesktop.org/show_bug.cgi?id=108039
fdo#108130 https://bugs.freedesktop.org/show_bug.cgi?id=108130
fdo#108145 https://bugs.freedesktop.org/show_bug.cgi?id=108145
fdo#99912 https://bugs.freedesktop.org/show_bug.cgi?id=99912
== Participating hosts (6 -> 4) ==
Missing (2): shard-glk shard-hsw
== Build changes ==
* Linux: CI_DRM_4925 -> Patchwork_10351
CI_DRM_4925: b652f33e63e1aafb7fc1cb2a9648a14d66f0d35f @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4665: 267870165d9ef66b4ab423e4efe7bacba023d75e @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_10351: 514e604a2b9a7a2422d760c87651585b6896a1c5 @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit
== Logs ==
For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10351/shards.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx