Skip to contentSkip to conversation

Watermarks small fixes/improvements

PATCH In review Paulo Zanoni 3 participants 18 messages Oct 4, 2018 – Oct 11, 2018

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

cover Watermarks small fixes/improvements

I'm investigating ICL watermarks failures and these are some of the immediate problems I was able to find in the watermarks code. I don't think they're enough to fix the problems our CI is able to reproduce, but I do think these changes are worth having.

Paulo Zanoni (6):
drm/i915: don't apply Display WAs 1125 and 1126 to GLK/CNL+ drm/i915: fix the transition minimums for gen9+ watermarks drm/i915: fix the watermark result selection on glk/gen10+ drm/i915: transition WMs ask for Selected Result Blocks drm/i915: don't write PLANE_BUF_CFG twice every time drm/i915: promote ddb update message to DRM_DEBUG_KMS

 drivers/gpu/drm/i915/intel_pm.c | 100 ++++++++++++++++++++++++----------------
 1 file changed, 61 insertions(+), 39 deletions(-)
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#1 lore raw

PATCH 1/6 drm/i915: don't apply Display WAs 1125 and 1126 to GLK/CNL+

BSpec does not show these WAs as applicable to GLK, and for CNL it only shows them applicable for a super early pre-production stepping we shouldn't be caring about anymore. Remove these so we can avoid them on ICL too.

---
 drivers/gpu/drm/i915/intel_pm.c | 43 ++++++++++++++++++++++-------------------
 1 file changed, 23 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +23 -20
index 1392aa56a55a..910551e04d16 100644
@@ -4687,28 +4687,31 @@ static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv,
 	res_lines = div_round_up_fixed16(selected_result,
 					 wp->plane_blocks_per_line);
 
-	/* Display WA #1125: skl,bxt,kbl,glk */
-	if (level == 0 && wp->rc_surface)
-		res_blocks += fixed16_to_u32_round_up(wp->y_tile_minimum);
+	if (IS_GEN9(dev_priv) && !IS_GEMINILAKE(dev_priv)) {
+		/* Display WA #1125: skl,bxt,kbl */
+		if (level == 0 && wp->rc_surface)
+			res_blocks +=
+				fixed16_to_u32_round_up(wp->y_tile_minimum);
+
+		/* Display WA #1126: skl,bxt,kbl */
+		if (level >= 1 && level <= 7) {
+			if (wp->y_tiled) {
+				res_blocks +=
+				    fixed16_to_u32_round_up(wp->y_tile_minimum);
+				res_lines += wp->y_min_scanlines;
+			} else {
+				res_blocks++;
+			}
 
-	/* Display WA #1126: skl,bxt,kbl,glk */
-	if (level >= 1 && level <= 7) {
-		if (wp->y_tiled) {
-			res_blocks += fixed16_to_u32_round_up(
-							wp->y_tile_minimum);
-			res_lines += wp->y_min_scanlines;
-		} else {
-			res_blocks++;
+			/*
+			 * Make sure result blocks for higher latency levels are
+			 * atleast as high as level below the current level.
+			 * Assumption in DDB algorithm optimization for special
+			 * cases. Also covers Display WA #1125 for RC.
+			 */
+			if (result_prev->plane_res_b > res_blocks)
+				res_blocks = result_prev->plane_res_b;
 		}
-
-		/*
-		 * Make sure result blocks for higher latency levels are atleast
-		 * as high as level below the current level.
-		 * Assumption in DDB algorithm optimization for special cases.
-		 * Also covers Display WA #1125 for RC.
-		 */
-		if (result_prev->plane_res_b > res_blocks)
-			res_blocks = result_prev->plane_res_b;
 	}
 
 	if (INTEL_GEN(dev_priv) >= 11) {
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#2 lore raw

Re: [PATCH 1/6] drm/i915: don't apply Display WAs 1125 and 1126 to GLK/CNL+

Quoted 6 lines · Paulo Zanoni

BSpec does not show these WAs as applicable to GLK, and for CNL it only shows them applicable for a super early pre-production stepping we shouldn't be caring about anymore. Remove these so we can avoid them on ICL too.

From a quick grep, it looks like there's a couple other CNL A0-specific workarounds in the codebase (in the watermark code). If we don't want to handle CNL A0 in this patch, then I think we should first land a patch that removes the others and updates intel_detect_preproduction_hw() to make it explicit that this is no longer a supported stepping.

Quoted 9 lines
---
 drivers/gpu/drm/i915/intel_pm.c | 43 ++++++++++++++++++++++-------------------
 1 file changed, 23 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +0 -0
index 1392aa56a55a..910551e04d16 100644

drivers/gpu/drm/i915/intel_pm.c static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv, · line 4691

Quoted 8 lines
drivers/gpu/drm/i915/intel_pm.c +2 -3
@@ -4687,28 +4687,31 @@ static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv,
 	res_lines = div_round_up_fixed16(selected_result,
 					 wp->plane_blocks_per_line);
 
-	/* Display WA #1125: skl,bxt,kbl,glk */
-	if (level == 0 && wp->rc_surface)
-		res_blocks += fixed16_to_u32_round_up(wp->y_tile_minimum);
+	if (IS_GEN9(dev_priv) && !IS_GEMINILAKE(dev_priv)) {
+		/* Display WA #1125: skl,bxt,kbl */

Although the code is right, should we just write "gen9" (or gen9display) in this comment (and the one for 1126)? That's how the bspec lists it (GEN9:All), and removes the ambiguity of whether "kbl" in this context is also supposed to cover CFL, AML, WHL (which it does).

Matt

Quoted 50 lines
drivers/gpu/drm/i915/intel_pm.c +21 -17
+		if (level == 0 && wp->rc_surface)
+			res_blocks +=
+				fixed16_to_u32_round_up(wp->y_tile_minimum);
+
+		/* Display WA #1126: skl,bxt,kbl */
+		if (level >= 1 && level <= 7) {
+			if (wp->y_tiled) {
+				res_blocks +=
+				    fixed16_to_u32_round_up(wp->y_tile_minimum);
+				res_lines += wp->y_min_scanlines;
+			} else {
+				res_blocks++;
+			}
 
-	/* Display WA #1126: skl,bxt,kbl,glk */
-	if (level >= 1 && level <= 7) {
-		if (wp->y_tiled) {
-			res_blocks += fixed16_to_u32_round_up(
-							wp->y_tile_minimum);
-			res_lines += wp->y_min_scanlines;
-		} else {
-			res_blocks++;
+			/*
+			 * Make sure result blocks for higher latency levels are
+			 * atleast as high as level below the current level.
+			 * Assumption in DDB algorithm optimization for special
+			 * cases. Also covers Display WA #1125 for RC.
+			 */
+			if (result_prev->plane_res_b > res_blocks)
+				res_blocks = result_prev->plane_res_b;
 		}
-
-		/*
-		 * Make sure result blocks for higher latency levels are atleast
-		 * as high as level below the current level.
-		 * Assumption in DDB algorithm optimization for special cases.
-		 * Also covers Display WA #1125 for RC.
-		 */
-		if (result_prev->plane_res_b > res_blocks)
-			res_blocks = result_prev->plane_res_b;
 	}
 
 	if (INTEL_GEN(dev_priv) >= 11) {
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 9 lines
Matt Roper
Graphics Software Engineer
IoTG Platform Enabling & Development
Intel Corporation
(916) 356-2795
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#3 lore raw

Re: [PATCH 1/6] drm/i915: don't apply Display WAs 1125 and 1126 to GLK/CNL+

Em Ter, 2018-10-09 às 16:55 -0700, Matt Roper escreveu:

Quoted 9 lines · Paulo Zanoni
Quoted 7 lines

BSpec does not show these WAs as applicable to GLK, and for CNL it only shows them applicable for a super early pre-production stepping
we shouldn't be caring about anymore. Remove these so we can avoid them on ICL too.

Quoted 8 lines

From a quick grep, it looks like there's a couple other CNL A0- specific
workarounds in the codebase (in the watermark code). If we don't want
to handle CNL A0 in this patch, then I think we should first land a patch that removes the others and updates intel_detect_preproduction_hw() to make it explicit that this is no longer a supported stepping.

This patch (and series) is potentially a "bug fix" due to changes in real-world not-A0 hardware (although I didn't mark this one as a fix since I doubt it will close anything in Bugzilla). The patch to remove the implementation of WAs in CNL:A0 is not a bug fix, but a rework. Fixes should always come before the reworks in order to facilitate backporting efforts.

I do intend to propose patches removing the CNL A0 watermarks code (along with other reworks I have in mind), but I wanted to sort the bugs first.

Quoted 21 lines
Quoted 21 lines
---
 drivers/gpu/drm/i915/intel_pm.c | 43 ++++++++++++++++++++++-------
------------
 1 file changed, 23 insertions(+), 20 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +0 -3
index 1392aa56a55a..910551e04d16 100644
@@ -4687,28 +4687,31 @@ static int skl_compute_plane_wm(const
 struct drm_i915_private *dev_priv,
 	res_lines = div_round_up_fixed16(selected_result,
 					 wp-
 >plane_blocks_per_line);
 
-	/* Display WA #1125: skl,bxt,kbl,glk */
-	if (level == 0 && wp->rc_surface)
-		res_blocks += fixed16_to_u32_round_up(wp-
 >y_tile_minimum);
Quoted 10 lines

drivers/gpu/drm/i915/intel_pm.c static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv, · line 4691

Quoted 2 lines
drivers/gpu/drm/i915/intel_pm.c +2 -0
+	if (IS_GEN9(dev_priv) && !IS_GEMINILAKE(dev_priv)) {
+		/* Display WA #1125: skl,bxt,kbl */

Although the code is right, should we just write "gen9" (or gen9display)
in this comment (and the one for 1126)? That's how the bspec lists it
(GEN9:All), and removes the ambiguity of whether "kbl" in this context
is also supposed to cover CFL, AML, WHL (which it does).

Although that makes sense, it doesn't seem to follow the current (undocumented?) standard we have for display WAs. I can totally do this, but I would like some more opinions first. CC'ing the maintainers.

Thanks for the reviews,
Paulo

Quoted 56 lines

Matt

Quoted 52 lines
drivers/gpu/drm/i915/intel_pm.c +15 -8
+		if (level == 0 && wp->rc_surface)
+			res_blocks +=
+				fixed16_to_u32_round_up(wp-
 >y_tile_minimum);
+
+		/* Display WA #1126: skl,bxt,kbl */
+		if (level >= 1 && level <= 7) {
+			if (wp->y_tiled) {
+				res_blocks +=
+				    fixed16_to_u32_round_up(wp-
 >y_tile_minimum);
+				res_lines += wp->y_min_scanlines;
+			} else {
+				res_blocks++;
+			}
 
-	/* Display WA #1126: skl,bxt,kbl,glk */
-	if (level >= 1 && level <= 7) {
-		if (wp->y_tiled) {
-			res_blocks += fixed16_to_u32_round_up(
-							wp-
 >y_tile_minimum);
-			res_lines += wp->y_min_scanlines;
-		} else {
-			res_blocks++;
+			/*
+			 * Make sure result blocks for higher

latency levels are

drivers/gpu/drm/i915/intel_pm.c +1 -0
+			 * atleast as high as level below the

current level.

drivers/gpu/drm/i915/intel_pm.c +1 -0
+			 * Assumption in DDB algorithm

optimization for special

drivers/gpu/drm/i915/intel_pm.c +1 -0
+			 * cases. Also covers Display WA #1125 for

RC.

drivers/gpu/drm/i915/intel_pm.c +3 -0
+			 */
+			if (result_prev->plane_res_b > res_blocks)
+				res_blocks = result_prev-
Quoted 1 line

plane_res_b;

drivers/gpu/drm/i915/intel_pm.c +0 -3
 		}
-
-		/*
-		 * Make sure result blocks for higher latency

levels are atleast

drivers/gpu/drm/i915/intel_pm.c +0 -2
-		 * as high as level below the current level.
-		 * Assumption in DDB algorithm optimization for

special cases.

drivers/gpu/drm/i915/intel_pm.c +0 -4
-		 * Also covers Display WA #1125 for RC.
-		 */
-		if (result_prev->plane_res_b > res_blocks)
-			res_blocks = result_prev->plane_res_b;
 	}
Quoted 10 lines
Quoted 8 lines

if (INTEL_GEN(dev_priv) >= 11) {

Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#4 lore raw

PATCH 2/6 drm/i915: fix the transition minimums for gen9+ watermarks

In reply to Paulo Zanoni

The transition minimum is 14 blocks for gens 9 and 10, and 4 blocks for gen 11. This minimum value is supposed to be added to the configurable trans_amount. This matches both BSpec and additional information provided by our HW engineers.

---
 drivers/gpu/drm/i915/intel_pm.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +2 -2
index 910551e04d16..cab86690a0ba 100644
@@ -4878,8 +4878,8 @@ static void skl_compute_transition_wm(struct intel_crtc_state *cstate,
 	if (!dev_priv->ipc_enabled)
 		goto exit;
 
-	trans_min = 0;
-	if (INTEL_GEN(dev_priv) >= 10)
+	trans_min = 14;
+	if (INTEL_GEN(dev_priv) >= 11)
 		trans_min = 4;
 
 	trans_offset_b = trans_min + trans_amount;
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Reviewed-by on v1 2/6
#5 lore raw

Re: [PATCH 2/6] drm/i915: fix the transition minimums for gen9+ watermarks

Quoted 6 lines · Paulo Zanoni

The transition minimum is 14 blocks for gens 9 and 10, and 4 blocks for gen 11. This minimum value is supposed to be added to the configurable trans_amount. This matches both BSpec and additional information provided by our HW engineers.

Matches what I see in the bspec.

Quoted 26 lines
---
 drivers/gpu/drm/i915/intel_pm.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +2 -2
index 910551e04d16..cab86690a0ba 100644
@@ -4878,8 +4878,8 @@ static void skl_compute_transition_wm(struct intel_crtc_state *cstate,
 	if (!dev_priv->ipc_enabled)
 		goto exit;
 
-	trans_min = 0;
-	if (INTEL_GEN(dev_priv) >= 10)
+	trans_min = 14;
+	if (INTEL_GEN(dev_priv) >= 11)
 		trans_min = 4;
 
 	trans_offset_b = trans_min + trans_amount;
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 9 lines
Matt Roper
Graphics Software Engineer
IoTG Platform Enabling & Development
Intel Corporation
(916) 356-2795
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#6 lore raw

PATCH 3/6 drm/i915: fix the watermark result selection on glk/gen10+

In reply to Paulo Zanoni

On these platforms we're supposed to unconditonally pick the method 2 result instead of the minimum.

---
 drivers/gpu/drm/i915/intel_pm.c | 23 ++++++++++++++++-------
 1 file changed, 16 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +16 -7
index cab86690a0ba..40ce99c455f3 100644
@@ -4672,15 +4672,24 @@ static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv,
 	} else {
 		if ((wp->cpp * cstate->base.adjusted_mode.crtc_htotal /
 		     wp->dbuf_block_size < 1) &&
-		     (wp->plane_bytes_per_line / wp->dbuf_block_size < 1))
+		     (wp->plane_bytes_per_line / wp->dbuf_block_size < 1)) {
 			selected_result = method2;
-		else if (ddb_allocation >=
-			 fixed16_to_u32_round_up(wp->plane_blocks_per_line))
-			selected_result = min_fixed16(method1, method2);
-		else if (latency >= wp->linetime_us)
-			selected_result = min_fixed16(method1, method2);
-		else
+		} else if (ddb_allocation >=
+			 fixed16_to_u32_round_up(wp->plane_blocks_per_line)) {
+			if (INTEL_GEN(dev_priv) == 9 &&
+			    !IS_GEMINILAKE(dev_priv))
+				selected_result = min_fixed16(method1, method2);
+			else
+				selected_result = method2;
+		} else if (latency >= wp->linetime_us) {
+			if (INTEL_GEN(dev_priv) == 9 &&
+			    !IS_GEMINILAKE(dev_priv))
+				selected_result = min_fixed16(method1, method2);
+			else
+				selected_result = method2;
+		} else {
 			selected_result = method1;
+		}
 	}
 
 	res_blocks = fixed16_to_u32_round_up(selected_result) + 1;
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#7 lore raw

Re: [PATCH 3/6] drm/i915: fix the watermark result selection on glk/gen10+

Quoted 2 lines · Paulo Zanoni

On these platforms we're supposed to unconditonally pick the method 2 result instead of the minimum.

In addition to this, it looks like the calculations for method 1 and method 2 need a slight update. gen10/gen11 adds an extra "+1" to the end of the method1 calculation and also to the interm_pbpl used in various method 2 calculations.

Matt

Quoted 49 lines
---
 drivers/gpu/drm/i915/intel_pm.c | 23 ++++++++++++++++-------
 1 file changed, 16 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +16 -7
index cab86690a0ba..40ce99c455f3 100644
@@ -4672,15 +4672,24 @@ static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv,
 	} else {
 		if ((wp->cpp * cstate->base.adjusted_mode.crtc_htotal /
 		     wp->dbuf_block_size < 1) &&
-		     (wp->plane_bytes_per_line / wp->dbuf_block_size < 1))
+		     (wp->plane_bytes_per_line / wp->dbuf_block_size < 1)) {
 			selected_result = method2;
-		else if (ddb_allocation >=
-			 fixed16_to_u32_round_up(wp->plane_blocks_per_line))
-			selected_result = min_fixed16(method1, method2);
-		else if (latency >= wp->linetime_us)
-			selected_result = min_fixed16(method1, method2);
-		else
+		} else if (ddb_allocation >=
+			 fixed16_to_u32_round_up(wp->plane_blocks_per_line)) {
+			if (INTEL_GEN(dev_priv) == 9 &&
+			    !IS_GEMINILAKE(dev_priv))
+				selected_result = min_fixed16(method1, method2);
+			else
+				selected_result = method2;
+		} else if (latency >= wp->linetime_us) {
+			if (INTEL_GEN(dev_priv) == 9 &&
+			    !IS_GEMINILAKE(dev_priv))
+				selected_result = min_fixed16(method1, method2);
+			else
+				selected_result = method2;
+		} else {
 			selected_result = method1;
+		}
 	}
 
 	res_blocks = fixed16_to_u32_round_up(selected_result) + 1;
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 9 lines
Matt Roper
Graphics Software Engineer
IoTG Platform Enabling & Development
Intel Corporation
(916) 356-2795
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Reviewed-by
#8 lore raw

Re: [PATCH 3/6] drm/i915: fix the watermark result selection on glk/gen10+

Quoted 9 lines · Matt Roper
Quoted 2 lines · Paulo Zanoni

On these platforms we're supposed to unconditonally pick the method 2 result instead of the minimum.

In addition to this, it looks like the calculations for method 1 and method 2 need a slight update. gen10/gen11 adds an extra "+1" to the end of the method1 calculation and also to the interm_pbpl used in various method 2 calculations.

Actually, it looks like you've already made these updates in a previous patch; disregard this comment.

The rest of this patch looks good.

Quoted 63 lines

Matt

Quoted 49 lines
---
 drivers/gpu/drm/i915/intel_pm.c | 23 ++++++++++++++++-------
 1 file changed, 16 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +16 -7
index cab86690a0ba..40ce99c455f3 100644
@@ -4672,15 +4672,24 @@ static int skl_compute_plane_wm(const struct drm_i915_private *dev_priv,
 	} else {
 		if ((wp->cpp * cstate->base.adjusted_mode.crtc_htotal /
 		     wp->dbuf_block_size < 1) &&
-		     (wp->plane_bytes_per_line / wp->dbuf_block_size < 1))
+		     (wp->plane_bytes_per_line / wp->dbuf_block_size < 1)) {
 			selected_result = method2;
-		else if (ddb_allocation >=
-			 fixed16_to_u32_round_up(wp->plane_blocks_per_line))
-			selected_result = min_fixed16(method1, method2);
-		else if (latency >= wp->linetime_us)
-			selected_result = min_fixed16(method1, method2);
-		else
+		} else if (ddb_allocation >=
+			 fixed16_to_u32_round_up(wp->plane_blocks_per_line)) {
+			if (INTEL_GEN(dev_priv) == 9 &&
+			    !IS_GEMINILAKE(dev_priv))
+				selected_result = min_fixed16(method1, method2);
+			else
+				selected_result = method2;
+		} else if (latency >= wp->linetime_us) {
+			if (INTEL_GEN(dev_priv) == 9 &&
+			    !IS_GEMINILAKE(dev_priv))
+				selected_result = min_fixed16(method1, method2);
+			else
+				selected_result = method2;
+		} else {
 			selected_result = method1;
+		}
 	}
 
 	res_blocks = fixed16_to_u32_round_up(selected_result) + 1;
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 9 lines
Matt Roper
Graphics Software Engineer
IoTG Platform Enabling & Development
Intel Corporation
(916) 356-2795
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 9 lines
Matt Roper
Graphics Software Engineer
IoTG Platform Enabling & Development
Intel Corporation
(916) 356-2795
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#9 lore raw

PATCH 4/6 drm/i915: transition WMs ask for Selected Result Blocks

In reply to Paulo Zanoni

The transition watermarks ask for Selected Result Blocks (the real value), not Result Blocks (the integer value). Given how ceilings are applied in both the non-transition and the transition watermarks calculations, we can get away with assuming that Selected Result Blocks is actually Result Blocks minus 1 without any rounding errors.

---
 drivers/gpu/drm/i915/intel_pm.c | 18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +15 -3
index 40ce99c455f3..14f13a371989 100644
@@ -4874,7 +4874,7 @@ static void skl_compute_transition_wm(struct intel_crtc_state *cstate,
 	const struct drm_i915_private *dev_priv = to_i915(dev);
 	uint16_t trans_min, trans_y_tile_min;
 	const uint16_t trans_amount = 10; /* This is configurable amount */
-	uint16_t trans_offset_b, res_blocks;
+	uint16_t wm0_sel_res_b, trans_offset_b, res_blocks;
 
 	if (!cstate->base.active)
 		goto exit;
@@ -4893,13 +4893,25 @@ static void skl_compute_transition_wm(struct intel_crtc_state *cstate,
 
 	trans_offset_b = trans_min + trans_amount;
 
+	/*
+	 * The spec asks for Selected Result Blocks for wm0 (the real value),
+	 * not Result Blocks (the integer value). Pay attention to the capital
+	 * letters. The value wm_l0->plane_res_b is actually Result Blocks, but
+	 * since Result Blocks is the ceiling of Selected Result Blocks plus 1,
+	 * and since we later will have to get the ceiling of the sum in the
+	 * transition watermarks calculation, we can just pretend Selected
+	 * Result Blocks is Result Blocks minus 1 and it should work for the
+	 * current platforms.
+	 */
+	wm0_sel_res_b = wm_l0->plane_res_b - 1;
+
 	if (wp->y_tiled) {
 		trans_y_tile_min = (uint16_t) mul_round_up_u32_fixed16(2,
 							wp->y_tile_minimum);
-		res_blocks = max(wm_l0->plane_res_b, trans_y_tile_min) +
+		res_blocks = max(wm0_sel_res_b, trans_y_tile_min) +
 				trans_offset_b;
 	} else {
-		res_blocks = wm_l0->plane_res_b + trans_offset_b;
+		res_blocks = wm0_sel_res_b + trans_offset_b;
 
 		/* WA BUG:1938466 add one block for non y-tile planes */
 		if (IS_CNL_REVID(dev_priv, CNL_REVID_A0, CNL_REVID_A0))
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Reviewed-by on v1 4/6
#10 lore raw

Re: [PATCH 4/6] drm/i915: transition WMs ask for Selected Result Blocks

Quoted 7 lines · Paulo Zanoni

The transition watermarks ask for Selected Result Blocks (the real value), not Result Blocks (the integer value). Given how ceilings are applied in both the non-transition and the transition watermarks calculations, we can get away with assuming that Selected Result Blocks is actually Result Blocks minus 1 without any rounding errors.

Matches current bspec.

I wonder if we should make trans_amount configurable via debugfs so that we can experiment with the impact of transitional watermarks.

Matt

Quoted 52 lines
---
 drivers/gpu/drm/i915/intel_pm.c | 18 +++++++++++++++---
 1 file changed, 15 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +15 -3
index 40ce99c455f3..14f13a371989 100644
@@ -4874,7 +4874,7 @@ static void skl_compute_transition_wm(struct intel_crtc_state *cstate,
 	const struct drm_i915_private *dev_priv = to_i915(dev);
 	uint16_t trans_min, trans_y_tile_min;
 	const uint16_t trans_amount = 10; /* This is configurable amount */
-	uint16_t trans_offset_b, res_blocks;
+	uint16_t wm0_sel_res_b, trans_offset_b, res_blocks;
 
 	if (!cstate->base.active)
 		goto exit;
@@ -4893,13 +4893,25 @@ static void skl_compute_transition_wm(struct intel_crtc_state *cstate,
 
 	trans_offset_b = trans_min + trans_amount;
 
+	/*
+	 * The spec asks for Selected Result Blocks for wm0 (the real value),
+	 * not Result Blocks (the integer value). Pay attention to the capital
+	 * letters. The value wm_l0->plane_res_b is actually Result Blocks, but
+	 * since Result Blocks is the ceiling of Selected Result Blocks plus 1,
+	 * and since we later will have to get the ceiling of the sum in the
+	 * transition watermarks calculation, we can just pretend Selected
+	 * Result Blocks is Result Blocks minus 1 and it should work for the
+	 * current platforms.
+	 */
+	wm0_sel_res_b = wm_l0->plane_res_b - 1;
+
 	if (wp->y_tiled) {
 		trans_y_tile_min = (uint16_t) mul_round_up_u32_fixed16(2,
 							wp->y_tile_minimum);
-		res_blocks = max(wm_l0->plane_res_b, trans_y_tile_min) +
+		res_blocks = max(wm0_sel_res_b, trans_y_tile_min) +
 				trans_offset_b;
 	} else {
-		res_blocks = wm_l0->plane_res_b + trans_offset_b;
+		res_blocks = wm0_sel_res_b + trans_offset_b;
 
 		/* WA BUG:1938466 add one block for non y-tile planes */
 		if (IS_CNL_REVID(dev_priv, CNL_REVID_A0, CNL_REVID_A0))
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 9 lines
Matt Roper
Graphics Software Engineer
IoTG Platform Enabling & Development
Intel Corporation
(916) 356-2795
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#11 lore raw

PATCH 5/6 drm/i915: don't write PLANE_BUF_CFG twice every time

In reply to Paulo Zanoni

We were writing to PLANE_BUF_CFG(pipe, plane_id) twice for every platform, and we were even using different values on the gen10- planar case. The first write is useless since it just gets replaced with the next one, so kill it.

There's a lot to improve in the DDB code, but let's start by avoiding the double write.

---
 drivers/gpu/drm/i915/intel_pm.c | 2 --
 1 file changed, 2 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +0 -2
index 14f13a371989..53b4a9a2de69 100644
@@ -5040,8 +5040,6 @@ static void skl_write_plane_wm(struct intel_crtc *intel_crtc,
 	skl_write_wm_level(dev_priv, PLANE_WM_TRANS(pipe, plane_id),
 			   &wm->trans_wm);
 
-	skl_ddb_entry_write(dev_priv, PLANE_BUF_CFG(pipe, plane_id),
-			    &ddb->plane[pipe][plane_id]);
 	/* FIXME: add proper NV12 support for ICL. */
 	if (INTEL_GEN(dev_priv) >= 11)
 		return skl_ddb_entry_write(dev_priv,
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Reviewed-by on v1 5/6
#12 lore raw

Re: [PATCH 5/6] drm/i915: don't write PLANE_BUF_CFG twice every time

Quoted 9 lines · Paulo Zanoni

We were writing to PLANE_BUF_CFG(pipe, plane_id) twice for every platform, and we were even using different values on the gen10- planar case. The first write is useless since it just gets replaced with the next one, so kill it.

There's a lot to improve in the DDB code, but let's start by avoiding the double write.

Looks like leftover code that was intended for removal in commit b879d58ff31ba ("drm/i915/skl+: refactor WM calculation for NV12").

One other comment below.

Quoted 9 lines
---
 drivers/gpu/drm/i915/intel_pm.c | 2 --
 1 file changed, 2 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +0 -0
index 14f13a371989..53b4a9a2de69 100644

drivers/gpu/drm/i915/intel_pm.c static void skl_write_plane_wm(struct intel_crtc *intel_crtc, · line 5045

Quoted 8 lines
drivers/gpu/drm/i915/intel_pm.c +0 -2
@@ -5040,8 +5040,6 @@ static void skl_write_plane_wm(struct intel_crtc *intel_crtc,
 	skl_write_wm_level(dev_priv, PLANE_WM_TRANS(pipe, plane_id),
 			   &wm->trans_wm);
 
-	skl_ddb_entry_write(dev_priv, PLANE_BUF_CFG(pipe, plane_id),
-			    &ddb->plane[pipe][plane_id]);
 	/* FIXME: add proper NV12 support for ICL. */
 	if (INTEL_GEN(dev_priv) >= 11)
 		return skl_ddb_entry_write(dev_priv,

Neither this function nor skl_ddb_entry_write() have return values, so I'm surprised this doesn't raise a compiler warning. Maybe while we're touching this area of the code we should drop the 'return' here and convert the next 'if' to an 'else if.'

Matt

Quoted 7 lines
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 9 lines
Matt Roper
Graphics Software Engineer
IoTG Platform Enabling & Development
Intel Corporation
(916) 356-2795
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#13 lore raw

PATCH 6/6 drm/i915: promote ddb update message to DRM_DEBUG_KMS

In reply to Paulo Zanoni

This message is currently marked as DRM_DEBUG_ATOMIC. I would like it to be DRM_DEBUG_KMS since it is more KMS than atomic, and this will also make the message appear in the CI logs, which may or may not help us with some FIFO underrun bugs.

---
 drivers/gpu/drm/i915/intel_pm.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +5 -5
index 53b4a9a2de69..6cacddd16010 100644
@@ -5233,11 +5233,11 @@ skl_print_wm_changes(const struct drm_atomic_state *state)
 			if (skl_ddb_entry_equal(old, new))
 				continue;
 
-			DRM_DEBUG_ATOMIC("[PLANE:%d:%s] ddb (%d - %d) -> (%d - %d)\n",
-					 intel_plane->base.base.id,
-					 intel_plane->base.name,
-					 old->start, old->end,
-					 new->start, new->end);
+			DRM_DEBUG_KMS("[PLANE:%d:%s] ddb (%d - %d) -> (%d - %d)\n",
+				      intel_plane->base.base.id,
+				      intel_plane->base.name,
+				      old->start, old->end,
+				      new->start, new->end);
 		}
 	}
 }
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Reviewed-by on v1 6/6
#14 lore raw

Re: [PATCH 6/6] drm/i915: promote ddb update message to DRM_DEBUG_KMS

Quoted 6 lines · Paulo Zanoni

This message is currently marked as DRM_DEBUG_ATOMIC. I would like it to be DRM_DEBUG_KMS since it is more KMS than atomic, and this will also make the message appear in the CI logs, which may or may not help us with some FIFO underrun bugs.

Quoted 32 lines
---
 drivers/gpu/drm/i915/intel_pm.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/gpu/drm/i915/intel_pm.c +5 -5
index 53b4a9a2de69..6cacddd16010 100644
@@ -5233,11 +5233,11 @@ skl_print_wm_changes(const struct drm_atomic_state *state)
 			if (skl_ddb_entry_equal(old, new))
 				continue;
 
-			DRM_DEBUG_ATOMIC("[PLANE:%d:%s] ddb (%d - %d) -> (%d - %d)\n",
-					 intel_plane->base.base.id,
-					 intel_plane->base.name,
-					 old->start, old->end,
-					 new->start, new->end);
+			DRM_DEBUG_KMS("[PLANE:%d:%s] ddb (%d - %d) -> (%d - %d)\n",
+				      intel_plane->base.base.id,
+				      intel_plane->base.name,
+				      old->start, old->end,
+				      new->start, new->end);
 		}
 	}
 }
Signature · 6 lines
2.14.4

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Signature · 9 lines
Matt Roper
Graphics Software Engineer
IoTG Platform Enabling & Development
Intel Corporation
(916) 356-2795
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#15 lore raw

✗ Fi.CI.SPARSE: warning for Watermarks small fixes/improvements

In reply to Paulo Zanoni
== Series Details ==

== Series Details ==

Series: Watermarks small fixes/improvements
URL : https://patchwork.freedesktop.org/series/50579/
State : warning

== Summary ==

$ dim sparse origin/drm-tip
Commit: drm/i915: don't apply Display WAs 1125 and 1126 to GLK/CNL+
Okay!

Commit: drm/i915: fix the transition minimums for gen9+ watermarks Okay!

Commit: drm/i915: fix the watermark result selection on glk/gen10+ Okay!

Commit: drm/i915: transition WMs ask for Selected Result Blocks -O:drivers/gpu/drm/i915/intel_pm.c:4899:30: warning: expression using sizeof(void) -O:drivers/gpu/drm/i915/intel_pm.c:4899:30: warning: expression using sizeof(void) +drivers/gpu/drm/i915/intel_pm.c:4911:30: warning: expression using sizeof(void) +drivers/gpu/drm/i915/intel_pm.c:4911:30: warning: expression using sizeof(void)

Commit: drm/i915: don't write PLANE_BUF_CFG twice every time Okay!

Commit: drm/i915: promote ddb update message to DRM_DEBUG_KMS Okay!

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#16 lore raw

✓ Fi.CI.BAT: success for Watermarks small fixes/improvements

In reply to Paulo Zanoni
== Series Details ==

== Series Details ==

Series: Watermarks small fixes/improvements
URL : https://patchwork.freedesktop.org/series/50579/
State : success

== Summary ==

= CI Bug Log - changes from CI_DRM_4933 -> Patchwork_10368 =

== Summary - SUCCESS ==

No regressions found.

External URL: https://patchwork.freedesktop.org/api/1.0/series/50579/revisions/1/mbox/

== Known issues ==

Here are the changes found in Patchwork_10368 that come from known issues:

=== IGT changes ===

    ==== Issues hit ====

    igt@gem_exec_suspend@basic-s4-devices:
      fi-kbl-7500u:       PASS -> DMESG-WARN (fdo#105128, fdo#107139)

    igt@kms_flip@basic-plain-flip:
      fi-ilk-650:         PASS -> DMESG-WARN (fdo#106387)

    igt@kms_frontbuffer_tracking@basic:
      fi-byt-clapper:     PASS -> FAIL (fdo#103167)

    igt@kms_pipe_crc_basic@suspend-read-crc-pipe-a:
      fi-byt-clapper:     PASS -> FAIL (fdo#103191, fdo#107362)

    
    ==== Possible fixes ====

    igt@kms_pipe_crc_basic@nonblocking-crc-pipe-a:
      fi-byt-clapper:     FAIL (fdo#107362) -> PASS

fdo#103167 https://bugs.freedesktop.org/show_bug.cgi?id=103167
fdo#103191 https://bugs.freedesktop.org/show_bug.cgi?id=103191
fdo#105128 https://bugs.freedesktop.org/show_bug.cgi?id=105128
fdo#106387 https://bugs.freedesktop.org/show_bug.cgi?id=106387
fdo#107139 https://bugs.freedesktop.org/show_bug.cgi?id=107139
fdo#107362 https://bugs.freedesktop.org/show_bug.cgi?id=107362

== Participating hosts (44 -> 40) ==

Additional (2): fi-glk-j4005 fi-snb-2520m
Missing (6): fi-ilk-m540 fi-byt-squawks fi-bsw-cyan fi-icl-u2 fi-ctg-p8600 fi-pnv-d510

== Build changes ==

* Linux: CI_DRM_4933 -> Patchwork_10368

CI_DRM_4933: 6b7a44d1597791524f46d7ea17620db54dffdc8c @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4669: 5f40e617cd9c1e089f4a2d79c53a417d891e3e3c @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_10368: cb6ffc487ae82bef586cce9617a7f4b150118efc @ git://anongit.freedesktop.org/gfx-ci/linux

== Linux commits ==

cb6ffc487ae8 drm/i915: promote ddb update message to DRM_DEBUG_KMS ba4585dfc75c drm/i915: don't write PLANE_BUF_CFG twice every time bc9212a3b57e drm/i915: transition WMs ask for Selected Result Blocks c1245720e828 drm/i915: fix the watermark result selection on glk/gen10+ 47839a11088f drm/i915: fix the transition minimums for gen9+ watermarks 99b1569417cb drm/i915: don't apply Display WAs 1125 and 1126 to GLK/CNL+

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10368/issues.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#17 lore raw

✓ Fi.CI.IGT: success for Watermarks small fixes/improvements

In reply to Paulo Zanoni
== Series Details ==

== Series Details ==

Series: Watermarks small fixes/improvements
URL : https://patchwork.freedesktop.org/series/50579/
State : success

== Summary ==

= CI Bug Log - changes from CI_DRM_4933_full -> Patchwork_10368_full =

== Summary - WARNING ==

Minor unknown changes coming with Patchwork_10368_full need to be verified manually.

If you think the reported changes have nothing to do with the changes introduced in Patchwork_10368_full, please notify your bug team to allow them to document this new failure mode, which will reduce false positives in CI.

== Possible new issues ==

Here are the unknown changes that may have been introduced in Patchwork_10368_full:

=== IGT changes ===

    ==== Warnings ====

    igt@kms_frontbuffer_tracking@fbc-2p-primscrn-pri-shrfb-draw-blt:
      shard-hsw:          PASS -> SKIP

    igt@pm_rc6_residency@rc6-accuracy:
      shard-snb:          PASS -> SKIP

== Known issues ==

Here are the changes found in Patchwork_10368_full that come from known issues:

=== IGT changes ===

    ==== Issues hit ====

    igt@gem_ppgtt@blt-vs-render-ctxn:
      shard-skl:          NOTRUN -> TIMEOUT (fdo#108039)

    igt@gem_userptr_blits@readonly-unsync:
      shard-skl:          PASS -> INCOMPLETE (fdo#108074)

    igt@kms_busy@extended-modeset-hang-newfb-with-reset-render-a:
      shard-skl:          NOTRUN -> DMESG-WARN (fdo#107956)

    igt@kms_busy@extended-pageflip-hang-newfb-render-a:
      shard-apl:          PASS -> DMESG-WARN (fdo#107956)

    igt@kms_color@pipe-a-ctm-max:
      shard-apl:          PASS -> FAIL (fdo#108147)

    igt@kms_cursor_legacy@2x-long-cursor-vs-flip-legacy:
      shard-hsw:          PASS -> FAIL (fdo#105767)

    igt@kms_cursor_legacy@cursorb-vs-flipb-toggle:
      shard-glk:          PASS -> DMESG-WARN (fdo#106538, fdo#105763)

    igt@kms_frontbuffer_tracking@fbc-1p-offscren-pri-indfb-draw-mmap-wc:
      shard-skl:          PASS -> FAIL (fdo#105682) +2

    igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-draw-pwrite:
      shard-apl:          PASS -> FAIL (fdo#103167) +3

    igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-fullscreen:
      shard-glk:          PASS -> FAIL (fdo#103167) +2

    igt@kms_plane@pixel-format-pipe-a-planes:
      shard-skl:          NOTRUN -> DMESG-WARN (fdo#106885)

    {igt@kms_plane_alpha_blend@pipe-a-coverage-7efc}:
      shard-skl:          PASS -> FAIL (fdo#108145)

    {igt@kms_plane_alpha_blend@pipe-b-coverage-7efc}:
      shard-skl:          NOTRUN -> FAIL (fdo#108146)

    {igt@kms_plane_alpha_blend@pipe-c-alpha-transparant-fb}:
      shard-skl:          NOTRUN -> FAIL (fdo#108145) +3

    igt@kms_plane_multiple@atomic-pipe-b-tiling-yf:
      shard-apl:          PASS -> FAIL (fdo#103166)

    igt@kms_rotation_crc@exhaust-fences:
      shard-skl:          NOTRUN -> DMESG-WARN (fdo#105748)

    igt@kms_setmode@basic:
      shard-kbl:          PASS -> FAIL (fdo#99912)

    igt@kms_sysfs_edid_timing:
      shard-skl:          NOTRUN -> FAIL (fdo#100047)

    
    ==== Possible fixes ====

    igt@gem_cpu_reloc@full:
      shard-skl:          INCOMPLETE (fdo#108073) -> PASS

    igt@kms_busy@extended-modeset-hang-oldfb-with-reset-render-b:
      shard-apl:          DMESG-WARN (fdo#103558, fdo#105602) -> PASS +1

    igt@kms_cursor_crc@cursor-128x128-random:
      shard-glk:          FAIL (fdo#103232) -> PASS

    igt@kms_cursor_crc@cursor-128x128-suspend:
      shard-apl:          FAIL (fdo#103191, fdo#103232) -> PASS

    igt@kms_cursor_crc@cursor-64x64-random:
      shard-apl:          FAIL (fdo#103232) -> PASS +1

    igt@kms_cursor_legacy@2x-long-nonblocking-modeset-vs-cursor-atomic:
      shard-glk:          FAIL (fdo#105454, fdo#106509) -> PASS

    igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-draw-mmap-wc:
      shard-glk:          FAIL (fdo#103167) -> PASS

    igt@kms_frontbuffer_tracking@fbc-1p-primscrn-spr-indfb-fullscreen:
      shard-apl:          FAIL (fdo#103167) -> PASS +1

    igt@kms_plane@plane-position-covered-pipe-b-planes:
      shard-apl:          FAIL (fdo#103166) -> PASS

    {igt@kms_plane_alpha_blend@pipe-c-alpha-opaque-fb}:
      shard-glk:          FAIL (fdo#108145) -> PASS

    igt@kms_plane_multiple@atomic-pipe-a-tiling-x:
      shard-glk:          DMESG-WARN (fdo#106538, fdo#105763) -> PASS +3

    igt@kms_plane_multiple@atomic-pipe-b-tiling-yf:
      shard-glk:          FAIL (fdo#103166) -> PASS

    igt@kms_setmode@basic:
      shard-apl:          FAIL (fdo#99912) -> PASS

    igt@pm_rpm@pm-tiling:
      shard-skl:          INCOMPLETE (fdo#107807) -> PASS +1

{name}: This element is suppressed. This means it is ignored when computing
the status of the difference (SUCCESS, WARNING, or FAILURE).

fdo#100047 https://bugs.freedesktop.org/show_bug.cgi?id=100047
fdo#103166 https://bugs.freedesktop.org/show_bug.cgi?id=103166
fdo#103167 https://bugs.freedesktop.org/show_bug.cgi?id=103167
fdo#103191 https://bugs.freedesktop.org/show_bug.cgi?id=103191
fdo#103232 https://bugs.freedesktop.org/show_bug.cgi?id=103232
fdo#103558 https://bugs.freedesktop.org/show_bug.cgi?id=103558
fdo#105454 https://bugs.freedesktop.org/show_bug.cgi?id=105454
fdo#105602 https://bugs.freedesktop.org/show_bug.cgi?id=105602
fdo#105682 https://bugs.freedesktop.org/show_bug.cgi?id=105682
fdo#105748 https://bugs.freedesktop.org/show_bug.cgi?id=105748
fdo#105763 https://bugs.freedesktop.org/show_bug.cgi?id=105763
fdo#105767 https://bugs.freedesktop.org/show_bug.cgi?id=105767
fdo#106509 https://bugs.freedesktop.org/show_bug.cgi?id=106509
fdo#106538 https://bugs.freedesktop.org/show_bug.cgi?id=106538
fdo#106885 https://bugs.freedesktop.org/show_bug.cgi?id=106885
fdo#107807 https://bugs.freedesktop.org/show_bug.cgi?id=107807
fdo#107956 https://bugs.freedesktop.org/show_bug.cgi?id=107956
fdo#108039 https://bugs.freedesktop.org/show_bug.cgi?id=108039
fdo#108073 https://bugs.freedesktop.org/show_bug.cgi?id=108073
fdo#108074 https://bugs.freedesktop.org/show_bug.cgi?id=108074
fdo#108145 https://bugs.freedesktop.org/show_bug.cgi?id=108145
fdo#108146 https://bugs.freedesktop.org/show_bug.cgi?id=108146
fdo#108147 https://bugs.freedesktop.org/show_bug.cgi?id=108147
fdo#99912 https://bugs.freedesktop.org/show_bug.cgi?id=99912

== Participating hosts (6 -> 6) ==

No changes in participating hosts

== Build changes ==

* Linux: CI_DRM_4933 -> Patchwork_10368

CI_DRM_4933: 6b7a44d1597791524f46d7ea17620db54dffdc8c @ git://anongit.freedesktop.org/gfx-ci/linux
IGT_4669: 5f40e617cd9c1e089f4a2d79c53a417d891e3e3c @ git://anongit.freedesktop.org/xorg/app/intel-gpu-tools
Patchwork_10368: cb6ffc487ae82bef586cce9617a7f4b150118efc @ git://anongit.freedesktop.org/gfx-ci/linux
piglit_4509: fdc5a4ca11124ab8413c7988896eec4c97336694 @ git://anongit.freedesktop.org/piglit

== Logs ==

For more details see: https://intel-gfx-ci.01.org/tree/drm-tip/Patchwork_10368/shards.html
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx